Testkings.ACMP_ questions. Aruba ACMP_6.3. Aruba Certified Mobility Professional 6.3

Transcription

1 Testkings.ACMP_ questions Number: ACMP_6.3 Passing Score: 800 Time Limit: 120 min File Version: Aruba ACMP_6.3 Aruba Certified Mobility Professional 6.3 My problem had solved because the products of it was very reliable This dumps is valid and awesome, I passed by just 2 days practice. A questions are all in the dump file and there is the additional question It was one and only which took me towards the biggest success without finding too much issues or worries in any way.

2 It guided me step by step through the course. After studying for a month using it I achieved the highest in the whole city

3 Exam A QUESTION 1 Which of the following Aruba controllers is able to provide IEEE 802.3af? (Choose two) A B. 620 C. 650 D with M3 E Correct Answer: BC /Reference: : QUESTION 2 What is the maximum number of remote APs supported by a 3600 controller? A. 512 B C. 128 D. 256 E Correct Answer: A /Reference: correct answer. QUESTION 3 What is the first role a user is given when a user associates to an open WLAN?

4 A. The guest post authentication role B. The initial role in the captive portal profile C. The role in the server group profile D. The initial role in the AAA profile E. The initial role in the 802.1x profile Correct Answer: D /Reference: : QUESTION 4 Which of the following could be used to set a user's post-authentication role or VLAN association? (Choose two) A. AAA default role for authentication method B. Server Derivation Rule C. Vendor Specific Attributes D. AP Derivation Rule E. The Global AAA profile Correct Answer: BC /Reference: : QUESTION 5

5 Which describe "roles" as used on Aruba Mobility Controllers? (Choose two) A. Roles are assigned to users. B. Roles are applied to interfaces. C. Policies are built from roles. D. A user can belong to only one role at a time. E. Roles are a set of authentication rules Correct Answer: AD /Reference: : Real 8 QUESTION 6 Which netdestination aliases are built into the controller? (Choose three) A. logon B. any C. user D. guest E. localip Correct Answer: BCE /Reference: properly answered. QUESTION 7 What are aliases used for?

6 A. Improve controller performance B. Simplify the configuration process C. Tie IP addresses to ports D. Assign rules to policies E. Assign policies to roles Correct Answer: B /Reference: : QUESTION 8 Which of the following firewall rules allows a user to initiate an ICMP session to other devices? (Choose two) A. localip any svc-icmp permit B. user any svc-icmp permit C. user user svc-icmp permit D. any any svc-icmp permit E. mswitch any svc-icmp permit Correct Answer: BD /Reference: Real 9

7 : QUESTION 9 The Aruba Policy Enforcement Firewall (PEF-NG) module supports destination network address translation (dst-nat). Which is the default use of this statement in an Aruba controller configuration? A. Source the IP addresses of users to specific IP address B. Redirect HTTP sessions to Captive Portal C. Redirect Access Points to another Aruba controller D. Provide a telnet connection to the controller E. Redirect a SSH session to terminate on the controller Correct Answer: B /Reference: : QUESTION 10 The Aruba Policy Enforcement Firewall (PEF) module supports source network address translation (src-nat). Which is a use of this statement in an Aruba configuration? A. Provide a single source IP address for users in a role B. Redirect Captive Portal HTTP sessions C. Redirect Access Points to another Aruba controller D. Provide IP addresses to clients E. Redirects clients to Aruba Firewall Correct Answer: A /Reference: : QUESTION 11

8 The network administrator wishes to terminate the VPN encryption on the Aruba controller. Real 10 When writing a firewall rule to accomplish the task of automatically moving the VPN traffic for the wireless clients from a third party VPN concentrator to an Aruba controller, which action needs to be configured in the rule? A. redirect to IPSec Group B. source NAT C. destination NAT D. redirect to tunnel E. redirect to GRE Correct Answer: C /Reference: : QUESTION 12 Review the following truncated output from an Aruba controller for this item. (example) #show rights logon access-list List Position Name Location logon-control 2 captiveportal logon-control

9 Priority Source Destination Service Action user any udp 68 deny 2 any any svc-icmp permit 3 any any svc-dns permit Real 11 4 any any svc-dhcp permit 5 any any svc-natt permit captiveportal Priority Source Destination Service Action user controller svc-https dst-nat user any svc-http dst-nat user any svc-https dst-nat user any svc-http-proxy1 dst-nat user any svc-http-proxy2 dst-nat user any svc-http-proxy3 dst-nat 8088 Based on the above output from an Aruba controller, an unauthenticated user assigned to the logon role attempts to start an http session to IP address What will happen? A. the user's traffic will be passed to the IP address because of the policy statement:

10 user any svc-http dst-nat 8080 B. the user's traffic will be passed to the IP address because of the policy statement: user any svc-https dst-nat 8081 C. the user's traffic will be passed to the IP address because of the policy statement: user any svc-http-proxy1 dst-nat 8088 D. the user will not reach the IP address because of the policy statement: user any svc-http dst-nat 8080 E. the user will not reach the IP address because of the implicit deny any any at the end of the policy. Correct Answer: D /Reference: : QUESTION 13 View the Server group screen shot above.

11 A company has provisioned the same VAP, AAA and SSID profiles at both its Miami and NY offices. This Server Group is applied for 802.1x authentication at both locations. The user's credentials are only found in the Miami Radius server "RadiusMiami". There is no Radius synchronization and both servers are reachable. What happens when the user attempts to authenticate? A. The controller recognizes the users Domain and sends the authentication request directly to RadiusMiami. B. The request is initially sent to RadiusNY1 then RadiusNY1 redirects the controller to send the authentication request to RadiusMiami C. RadiusNY1 receives the request and returns a deny. No other action is taken. D. RadiusNY1 receives the request and returns a deny. The authentication request will then be sent to RadiusMiami. E. The RadiusNY1 sends the request to RadiusMiami that replies to the controller Correct Answer: C /Reference: Real 17 QUESTION 14 View the Server group and User Roles screen shots above.

12 A user associated to an SSID with 802.1x using this server group. RadiusNY returned a standard radius attribute of filter-id with a value of "employee". The user was placed in the guest Role.

13 What statements below are correct? (Choose two) A. The user was placed in the 802.1x authentication default Role guest B. The user was placed in the initial Role guest C. Role derivation failed because roles are case sensitive D. Role derivation failed because the incorrect operation "value-of" was used E x authentication failed so the user was automatically placed in the guest Role Correct Answer: AC /Reference: : QUESTION 15 View the Server group and User Roles screen shots above. Real 18

14 A user associated to an SSID with 802.1x using this server group. RadiusNY returned a standard radius attribute of filter-id with a value of "employee".

15 What Role will the user get? A. The User will get the Emp Role B. The User will get the 802.1x authentication default Role C. The User will get the employee Role D. The User will get the Employee Role E. The User will get the initial Role Correct Answer: B /Reference: : QUESTION 16 Which profiles are required in an AP Group to enable an SSID with VLAN 1, WPA2 and LMSIP? (Choose three) A. Virtual-AP profile B. WLAN profile C x authentication profile D. AP System Profile E. SSID Profile Correct Answer: ADE /Reference: Real 19 : QUESTION 17 A user connected to a Captive Portal VAP successfully. When the user opens their browser and tries to access their homepage, they get redirected as expected to another URL on the Aruba Controller. However, they see an error message that web authentication has been disabled. What might be a cause of this? A. Captive Portal has not been assigned in the SSID profile.

16 B. The Captive portal profile has not been assigned to the AAA profile. C. A server group has not been assigned to the captive portal profile. D. An initial role has not been assigned to the AAA profile. E. The Captive portal profile has not been assigned to the initial role. Correct Answer: E /Reference: real answer. QUESTION 18 Which of the following will accept named VLANs as a parameter? (Choose three) A. Virtual AP profile B. User derivation rule for a single VLAN C. Server derivation rule for a single VLAN D. Server derivation rule for a VLAN Pool E. Access VLAN for a VLAN Pool Correct Answer: ABC /Reference: : QUESTION 19 A customer has a remote AP deployment, where each remote AP has an IPSEC VPN tunnel with L2TP to the controller. 1 of the remote APs is stuck in the user table and hasn't yet transitioned to the AP active table in the controller. The customer suspects that the AP is not setting up its VPN connection successfully. Which

17 of the following commands might be useful in troubleshooting this? (Choose three) Real 20 A. Logging level debugging security process localdb B. Logging level debugging security process l2tp C. Logging level debugging security process dot1x D. Logging level debugging security process crypto E. Logging level debugging security process vpn Correct Answer: ABD /Reference: : QUESTION 20 The screen captures below show the 802.1X authentication profile and AAA profile settings for a VAP.

18

19 If machine authentication fails and user authentication passes, which role will be assigned? Real 21 A. employee B. guest C. contractor D. logon E. no role is assigned Correct Answer: B /Reference: :

20 QUESTION 21 The screen captures above show the 802.1X authentication profile and AAA profile settings for a VAP.

21 Real 22 If machine authentication passes and user authentication fails, which role will be assigned? A. employee B. guest C. contractor D. logon E. no role is assigned Correct Answer: B /Reference: : QUESTION 22

22 The screen captures above show the 802.1X authentication profile and AAA profile settings for a VAP.

23 Real 23 If machine authentication fails and user authentication fails, which role will be assigned? A. Employee B. Guest C. Captive Portal D. Logon E. No role will be assigned Correct Answer: E /Reference: : QUESTION 23

24 What can NOT be configured from the Aruba controller configuration wizards? A. Controller IP B. Boot Partition C. User firewall policy. D. User derivation rules. E. Radius Servers Correct Answer: B /Reference: good answer. QUESTION 24 An administrator is setting up a factory default controller. No new AP groups were created. When adding a WLAN SSID in the Campus WLAN wizard what AP group is available? A. The air-monitors AP group B. The logon AP group C. The default AP group D. The initial AP group E. The Spectrum AP group Correct Answer: C /Reference: : Real 24 QUESTION 25 The reusable Aruba Controller wizards are accessible in what way? A. Only on startup through the CLI

25 B. Through the CLI, after the initial CLI wizard has been completed C. In the Web UI under maintenance. D. In the Web UI under configuration. E. Must be initialized from CLI first. Correct Answer: D /Reference: : QUESTION 26 The Contrtoller wizard enables which of the following controller clock configurations? (Choose three) A. NTP to a time server B. Set time zone C. Daylight savings time D. Only GMT can be configured E. Manual configuration of date and time Correct Answer: ABE /Reference: : QUESTION 27 When configuring ports in the Controller wizard, which of the following are NOT configuration options? (Choose two)

26 A. Inter-VLAN routing B. Speed C. Trusted D. LACP E. Trunk Correct Answer: AD /Reference: : Real 25 QUESTION 28 By default, which CLI based remote access method is enabled on Aruba controllers? A. RSH B. Telnet C. SSH D. Telnet and SSH E. Telnet, SSH and RSH Correct Answer: C /Reference: appropriate answer. QUESTION 29 An Aruba controller can be accessed with which CLI based remote access methods? (Choose two) A. RSH B. Telnet C. SSH

27 D. SFTP E. SCP Correct Answer: BC /Reference: : QUESTION 30 As an admin/root user, what other type of role-based management users can be created on Aruba controllers? A. Auditing-compliance user B. AirWave management user C. Reporting Generation user D. Guest provisioning user Real 26 E. Maintenance user Correct Answer: D /Reference: : QUESTION 31 Which log type should be enabled to troubleshoot IPSec authentication issues on Aruba Controllers? A. Security Logs B. Management Logs C. Wireless Logs D. IDS Logs E. System Logs Correct Answer: A

28 /Reference: fine answer. QUESTION 32 Exhibit: Real 27

29

30 Real 28 Referring to the above screen capture, if an administrator desires to change a specific AP into a Spectrum Monitor without assigning the AP to a new group, which menus could be used? A. Network > Controller B. Wireless > AP Configuration C. Wireless > AP Installation D. Advanced Services > Wireless E. Wizards > WIP Wizard Correct Answer: B /Reference: : QUESTION 33 A customer forgot all passwords for a controller. What method could you use to reset the passwords? A. Telnet to the controller and login to the password recovery account B. SSH to the controller and login to the password recovery account C. Connect directly to the serial console and login to the password recovery account D. Interrupt the boot process at CP-boot and select password recovery E. Open the controller and press the reset switch Correct Answer: C /Reference: : QUESTION 34 With CPSec disabled, which tunnel protocol is used between APs and Controllers in an Aruba environment?

31 A. Basic IP B. GRE C. IPinIP D. Mobile IP E. IPSec Correct Answer: B /Reference: : Real 29 QUESTION 35 In an Aruba controller based system, the L3 mobility tunnel exists between the home agent and which other element? A. the default gateway B. the remote AP C. the foreign agent D. the mobile node E. the foreign switch Correct Answer: C /Reference:

32 : QUESTION 36 When an client roams what device decides when to move the client to another AP? A. Aruba AP B. Aruba controller C. Client D. Radius Server E. Router Correct Answer: C /Reference: actual answer. QUESTION 37 Exhibit: Real 30

33 The above diagram has one master and three local controllers. AP1 GRE terminates on controller Local 1. All controllers are configured with the wireless user VLAN 201. A wireless user associates with AP 1. Only L2 mobility is enabled. Which elements will know about this association? A. Local 1 only B. Local 1 and the Master C. Local 1 and Local 2 and the Master D. Local 1 and AP1 E. All Controllers Correct Answer: B

34 /Reference: : QUESTION 38 Which command will show all client association history? A. Aruba-6000# show mobile trail current (ip address) B. Aruba-6000# show ip mobile trail (ip address) C. Aruba-6000# show ap client status (mac address) D. Aruba-6000# show current client ip (ip address) E. Aruba-6000# show client ip (ip address) mobility Real 31 Correct Answer: B /Reference: : QUESTION 39 With CPSec enabled, which tunnel protocol is used between APs and Controllers in an Aruba environment? A. EAP B. SSH C. IPinIP D. Mobile IP E. IPSec Correct Answer: E /Reference: :

35 QUESTION 40 By default, how long will an AP scan a single channel when ARM is enabled? A. 80 milliseconds B. 90 milliseconds C. 100 milliseconds D. 110 milliseconds E. 200 milliseconds Correct Answer: D /Reference: : QUESTION 41 Which actions does ARM (Adaptive Radio Management) perform? (Choose two) A. Allows controllers to provision the AP Radio type B. Allows controllers to provision the best channel for APs C. Allows controllers to provision the best power setting for APs D. Allows controllers to provision allowed Radio bands Real 32 E. Allows controllers to provision lower power when unauthorized APs are detected Correct Answer: BC /Reference: reliable answer QUESTION 42 Which of the following metrics does the ARM feature use to calculate the optimal channel and power level for Access Points? (Choose two) A. RF Spectrum Index B. Priority Index

36 C. Interference Index D. Coverage Index E. Frequency Index Correct Answer: CD /Reference: : QUESTION 43 How does the ARM Band Steering feature encourage 5GHz capable clients to move/connect to the 5GHz radios of Aruba APs? A. ARM suppresses the probe response on the 2.4 GHz radio B. ARM utilizes third party software on the wireless clients C. Current Wi-Fi chipset firmware supports this by default D. It's not possible the move clients to 5GHz radios when they can see both 2.4 and 5GHz APs E. ARM disables the 2.4Ghz radio for the specified client Correct Answer: A /Reference: : QUESTION 44 Which of the statements below are TRUE regarding ARM's Spectrum Load Balancing feature? (Choose two)

37 A. Available only on 5GHz radios B. Disabled by default C. Balances client load across available channels/aps D. Enabled by default E. Available only on 2.4GHz radios Correct Answer: BC /Reference: : QUESTION 45 What is the function of Band Steering? A. Balancing clients across APs on different channels within the same band B. Encourages clients, 5GHz capable, to connect on the 5GHz spectrum C. Coordinate access to the same channel across multiple APs D. Enables selection of 20 vs. 40 MHz mode of operation per band E. Enables acceptable coverage index on both the "b/g" and "a" spectrums Correct Answer: B /Reference: : QUESTION 46 What are the Airtime Allocation Policy options for Airtime Fairness? (Choose three) A. Default Access B. Priority Access C. Fair Access D. Preferred Access E. Distributed Access

38 Correct Answer: ACD /Reference: right answer. QUESTION 47 Which of the following statements is true of Spectrum Mode? Real 34 A. No licenses are required to run an AP in Spectrum mode B. Spectrum mode can only be configured for one AP at a time C. An AP can be in spectrum mode for both 2.4 and 5G bands at the same time D. An AP can be placed in Spectrum Mode via the Spectrum Profile E. Spectrum mode can be configured from the GUI under AP installation Correct Answer: C /Reference: : QUESTION 48 Which ARM feature addresses the issue of sticky clients by moving clients to associate to APs with better signal quality? A. Co-Channel interference mitigation B. Airtime Fairness C. ClientMatch D. Coordinated access to a single channel E. Band Steering Correct Answer: C

39 /Reference: : QUESTION 49 Aruba Client Match does NOT use which of the following parameters to determine the best AP for a client connection? (Choose two) A. Device type B. Location C. Signal to Noise Ratio D. Access Point load E. Spectrum Analysis Correct Answer: CD /Reference: : QUESTION 50 Real 35 Which settings cannot be modified directly from a local controller? A. Port VLAN setting B. Switch Time Zone C. Port trusted D. Roles E. SNMP Enable Trap Generation Correct Answer: D /Reference: properly answered. QUESTION 51 Masters communicate configuration information with locals using which tunnel type?

40 A. GRE B. IP in IP C. Provision Tunnel Protocol D. IPSec E. PPTP Correct Answer: D /Reference: : QUESTION 52 In the above screen capture: Real 36

41 The administrator notes that most of the configuration options are grayed out and have no action. What is the cause of the problem? A. attempting to make global changes on a Master Controller B. attempting to make global changes on a Local Controller C. this change can only be performed via the CLI D. does not have the correct software license

42 E. there is an error in the configuration Correct Answer: B /Reference: : QUESTION 53 Exhibit: Referring to the above screen capture, on which Controller can you create a vlan? A. Controller only B. Controller and only C. All three Controllers D. None of the Controllers E. Controller only

43 Correct Answer: C /Reference: : QUESTION 54 Exhibit: Referring to the above screen capture, on which controller can you add an administrative user and assign a controller management role? A. Controller only B. Controller and only C. All three Controllers D. Must be done in the RADIUS server E. Controller only Real 38 Correct Answer: C /Reference: : QUESTION 55

44 Refer to the above screen capture. By default, which controller's internal database will be used for user authentication? A. Controller only B. Controller and only C. All three Controllers D. You can't tell from this screen E. The Controller with the user session Correct Answer: A /Reference: fine answer. QUESTION 56 Real 44 How many Aruba controllers can be added to a single mobility domain? A. 64 controllers of any type B. 128 controllers supporting 2000 users C. 256 controllers with no more than 1024 subnets D. Controllers supporting up to 6000 AP's E. There is no controller limit

45 Correct Answer: E /Reference: : QUESTION 57 In a master-local controller scenario, where is the mobility domain defined? A. the AP group B. the master controller C. the local controller D. the master and the local controllers E. the master and the local controllers where roaming is needed Correct Answer: B /Reference: genuine answer. QUESTION 58 A university has 2 departments. Department 1 has its own mobility domain with one controller. Department 2 has multiple controllers configured in a second domain. The university is planning on offering a new application and needs users to be able to roam between both mobility domains. What is the best way to accomplish this? A. The 2 existing domains should be left as they are. A 3rd mobility domain should then be created and all 3 controllers need to be added to it B. Merge the controllers into the same mobility domain C. The IP subnets of all controllers need to be configured to match D. This cannot be accomplished E. Create a new domain between a department 1 controller and one of the department 2 controllers Real 45 Correct Answer: B

46 /Reference: : QUESTION 59 A port firewall policy is applied to a trunk port that denies controller access. An "allow all" Vlan firewall policy is applied to VLAN 33 on the same port. A user connected to VLAN 33 on that port attempts to gain access to the controller. Which of the following statements is true? A. The Port policy is applied, therefore no controller access B. The Vlan policy is applied, then the port policy, therefore no controller access C. The Vlan policy is applied, therefore access to the controller is allowed D. You cannot place a firewall policy on a Ports Vlan when the Port already has a policy, therefore no controller access E. When locally connected to a controller's port you always have controller access Correct Answer: C /Reference: : QUESTION 60 An access port has been placed in trusted mode. The Vlan on the port is in Untrusted mode. Which of the following statements is true? A. The traffic is trusted since the port is trusted B. The traffic is untrusted since the VLAN is untrusted C. This is an invalid configuration, both must be set the same D. You cannot set Vlans as trusted or untrusted E. Only traffic from that specific port is trusted, all other traffic is untrusted Correct Answer: B /Reference: :

47 QUESTION 61 A wired device is connected to an untrusted port on a controller. How can a role be assigned to the device? Real 46 A. An initial Role can be assigned directly to the VLAN B. Roles are assigned to devices connected to a trusted port C. A default Role can be directly assigned to an untrusted port D. Adding a wired AAA profile to a VLAN on the untrusted port E. The Role assigned to the untrusted port Correct Answer: D /Reference: : QUESTION 62 A port on a controller has been configured as untrusted. No wired access AAA profile or Global AAA profile is configured. When a user connects to that port which of the following statements is true? A. Since there is no wired access AAA profile, only port policies will be applied B. The user will fall into the default wired access AAA profile and will be given the initial role. C. Since there is no wired access AAA profile or Global AAA profile the user will be given the logon role. D. When configuring the port as untrusted, an error message of "no wired access AAA profile exists" Therefore this is an invalid configuration. E. the user is denied all access automatically because no wired access AAA or Global AAA profile is assigned. Correct Answer: C /Reference: actual answer. QUESTION 63 Which method can APs use to discover a controller?

48 A. DHCP B. Dynamic DNS (DDNS) C. PnP D. PAPI E. HTTPS Correct Answer: A /Reference: : Real 47 QUESTION 64 Which of the following configurations can accept a VLAN pool? (Choose two) A. Trunk native VLAN B. Virtual AP profile C. User Role D. Server derived role E. FW Policies Correct Answer: BC /Reference: : QUESTION 65 What does Aruba Layer 3 redundancy require to operate? A. LMS-IP B. Backup LMS-IP C. VRRP

49 D. Backup AP group E. ARM Correct Answer: B /Reference: : Real 53 QUESTION 66 Exhibit:

50 In the diagram provided for this question, the client laptop is associated with the Aruba AP. The Aruba controller is configured to perform L2 switching for this SSID. What will be the client laptop default gateway? A. A B. B

51 C. C D. D E. E Correct Answer: C /Reference: : QUESTION 67 Real 54 In the diagram provided for this question, the Aruba controller terminates one end of a GRE tunnel that carries wireless user traffic.

52 Where does the other end terminate? A. A B. B C. C D. D E. A or B Correct Answer: A

53 /Reference: : QUESTION 68 In the above diagram, the system shows two Aruba access points and a wired user. Real 55 Which VLAN(s) do NOT need to be configured on link A between the L2 switch and router to support the wireless users? A. 101 and 102 B. 101 and 103 C. 102 and 103 D. only 101 E. only 103 Correct Answer: A

54 /Reference: : QUESTION 69 In the above diagram, the system shows two Aruba access points. Real 56 Which VLANs must be configured on trunk link D between the router and Aruba controller to support wireless users when the controller is provisioned for L2 operations?

55 A. 10, 101 and 102 B. 101 and 102 C. 101, 102 and 103 D. 10, 101,102 and 103 E. 10 and 103 Correct Answer: A /Reference: : QUESTION 70 Exhibit: Real 57

56 Referring to the diagram provided for this question, if the Aruba controller is configured to perform L3 switching, what will be the wireless client laptop default gateway? A. A

57 B. B C. C D. D E. E Correct Answer: D /Reference: answer is suitable. QUESTION 71 When configuring Captive Portal, which protocols are supported when accessing the Captive Portal? (Choose two) A. HTTPS B. VPN C. HTTP D. TELNET E. SSH Real 58 Correct Answer: AC /Reference: : QUESTION 72 When the controller is configured for Captive Portal and the user is only required to provide an address for authentication, which option is configured in the GUI? A. enable termination B. enable guest logon C. enable user logon D. eap method

58 E. disable CP Login Correct Answer: B /Reference: : QUESTION 73 A user logged in with the Captive Portal settings shown in the above screen capture. Real 59

59 What does the user need to do to logout?

60 A. wait 30 minutes then logout B. wait 60 minutes then logout C. click Logout on the browser screen D. he cannot logout E. wait 10 seconds for redirect Correct Answer: C /Reference: : QUESTION 74 Screenshots of the Captive Portal authentication profile and server group of a guest network are displayed above. Real 60

61

62 How was the user authenticated? A. with a radius server called Radius01 B. with the Internal database C. with a radius server called Internal D. with another form of authentication E. user wasn't authenticated against any server Correct Answer: E /Reference: : Real 61 QUESTION 75 Where should mobility domains be enabled in a network with 1 master, 1 backup master and 5 local controllers?

63 A. Only on the master controller B. All the local controllers in the network C. All the controllers where the client is allowed to roam D. Master and backup master E. Only on the backup master Correct Answer: C /Reference: : QUESTION 76 What are two different methods of configuring AP redundancy between 2 local controllers? (Choose two) A. Fast-Failover B. Configure the locals as remote nodes C. Use named VLANS D. LMS and Backup LMS IP E. AP Redundancy can only be configured between a Master and Local Correct Answer: AD /Reference: sophisticated answer. QUESTION 77

64 An Aruba 650 controller is functioning as a standby Master. How many APs can it control while in standby mode? A. 0 B. 16 C. 24 D. 128 E. 256 Correct Answer: A /Reference: Real 62 : QUESTION 78 Aruba pair of 3200XM controllers are licensed to their maximum and are configured as a VRRP pair. Each controller terminates 24 APs. One of the controllers fails. How many of the APs from the failed controller can fail over to the remaining controller? A. 8 B. 16 C. 32 D. 48 E. 96 Correct Answer: A /Reference: : QUESTION 79 Which protocol does the Aruba controller utilize for controller redundancy? A. HSRP

65 B. VRRP C. VPN D. GRE E. IP-IP Correct Answer: B /Reference: : QUESTION 80 With Fast-Failover disabled, to which IP address should the Aruba AP terminate its GRE tunnel for layer 2 controller redundancy to work and to support failover of access points? A. VRRP IP address B. management IP of an Aruba controller C. management IP of the backup Aruba controller Real 63 D. HSRP IP address E. Loopback IP address of backup Aruba controller Correct Answer: A /Reference: : QUESTION 81 When an Aruba 6000 controller has two M3 modules installed, for which uses may the modules be used? (Choose two) A. hot standby operations B. VRRP backup C. higher AP density per switch chassis D. Active-Active masters

66 E. Active-Active master-backup Correct Answer: BC /Reference: : QUESTION 82 Referring to the diagram provided for this question, an employee brought an unauthorized AP from home and attached the LAN port to the cubicle Ethernet port. All Aruba APs and AMs as well as the employee AP are in VLAN 80 and within RF range of each other. No traffic from the wired or wireless network has passed through the unauthorized AP yet, but the AP began wireless broadcasts. Real 64

67

68 How will the Aruba system initially classify the employee's non-aruba AP? A. a valid AP B. an AM C. a Rogue AP D. an interfering AP E. a known interfering AP Correct Answer: D /Reference: : QUESTION 83 Referring to the diagram provided for this question, an employee brought an unauthorized AP from home and attached it to the cubicle Ethernet port as shown in the diagram. The APs are in VLANs as shown in the diagram. Only AP1 is within RF range.

69

70 How will the Aruba controller classify this AP? A. an AP B. an AM C. a Rogue AP D. an Interfering AP E. a workstation Correct Answer: D /Reference: : QUESTION 84 Referring to the diagram provided for this question, an employee brought an unauthorized AP from home, but did not attach it to the LAN infrastructure. The APs are in the VLANs as shown in the diagram. Only AP1 is within RF range of the employee AP. Real 66

71

72 By default, how will the Aruba system classify the employee's AP? A. an AP B. an AM C. a Rogue AP D. an Interfering AP E. a valid workstation Correct Answer: D /Reference: : QUESTION 85 What can an AM do that an AP cannot do? A. Detect rogue APs B. Detect an AP failure C. Scans all channels in under 1 minute D. Detect interfering APs E. Scan all valid channels Correct Answer: C /Reference: Real 67 : QUESTION 86 (group8) #show ap active Active AP Table

73 Name Group IP Address 11g Clients 11g Ch/EIRP/MaxEIRP 11a Clients 11a Ch/EIRP/MaxEIRP AP1 building AM 0 AM AP2 building AM 0 AM A user called technical support because they cannot see any of their APs in building one. You perform the "show" command as illustrated above. What can you conclude about these two APs from this output? A. the GRE for the APs terminate on two different controllers: and B. the system will not function because there is no building1 group defined C. the building1 APs will not accept any user connections D. the user needs to configure his client to use the b/g band E. the user needs to configure his client to use the a band Correct Answer: C /Reference: : QUESTION 87 Exhibit: Real 68

74 Based on the above screen capture for Interfering APs, what can you conclude? A. The APs must be connected to the Aruba network. B. The APs are classified as interfering because they are all transmitting on channel 6. C. There must not be any evidence that the APs are attached to the wired corporate network. D. These APs are classified as interfering because they are not Aruba APs. E. They are classified as interfering because they are running in g mode. Correct Answer: C /Reference: : QUESTION 88

75 As illustrated in the above diagram and screen capture, a wireless hacker injects messages into your network to detach a client from your Aruba AP.

76 Real 69 What action should you take to identify and prevent the Intruder from connecting to your system? (Choose two) A. Enable Detect disconnect Station Attack B. Enable Spoofed Deauth Blacklist C. Take no action as there is no protection against this form of attack D. Take no action as the Aruba system ignores this attack because it is against the client E. Enable Detect EAP rate Anomaly Correct Answer: AB /Reference: : QUESTION 89 (group8) #show ap arm history ap-name AP1 Interface :wifi0 ARM History Time of Change Old Channel New Channel Old Power New Power Reason :58: I :52: M :16: I Interface :wifi1 ARM History

77 Time of Change Old Channel New Channel Old Power New Power Reason :52: I Referring to the output above. What can you conclude about AP1? Real 70 A. This device is scanning channels. B. This device is unstable because the channel assignment changed. C. The device changed channels recently. D. The device changed channels and power levels recently. E. The device is transmitting at maximum power levels. Correct Answer: C /Reference: : QUESTION 90 An Aruba controller is configured with the correct IP address and gateway information and is connected to the corporate LAN via a core layer 2 switch. Control Plane Security is not enabled on the network. An access point is provisioned with AP name and group and connected to a different Layer 2 switch on the corporate LAN that has IP connectivity to the core layer 2 switch. The AP powers on and layer 2 connects to the network, but the wireless radios do not power on. Which could cause this condition? (Choose two) A. the layer 2 switches have ACLs that block GRE traffic B. the layer 2 switches are configured to block IPSec traffic C. a DHCP server is not configured for the segment to which the AP is connected D. the AP's mac address needs to be configured in the Aruba controller whitelist. E. the AP and controller are in different subnets

78 Correct Answer: AC /Reference: : QUESTION 91 In the diagram provided for this question, four buildings are identified on a college campus. Most of the wireless LAN traffic will be from students accessing the internet. Real 74

79

80 According to Aruba best practices, which building is the best location to install the Aruba mobility controller? A. data center B. dormitory C. server farm D. library E. 3rd party site Correct Answer: A /Reference: : QUESTION 92 Referring to the diagram provided for this question, representing an office wireless LAN deployment, there will be approximately 250 users in the offices section of the building. All Switches are setup as L3 routers. Real 75

81 According to Aruba best practice, which network device is the best choice for the wireless clients' default gateway? A. device 'A' B. device 'B' C. device 'C' D. device 'D' E. device 'C or D' Correct Answer: B

82 /Reference: exact answer. QUESTION 93 One hundred (100) additional APs were deployed in an existing network. But some APs are not able to connect to the lms-ip address, even though all of the APs belong to the same AP group. Which of the following are NOT potential causes? (Choose two) A. The problem APs are not getting an IP address. B. The problem APs have the wrong lms-ip address setting. C. There is a firewall between the problem APs and the controller blocking PAPI. D. The controller does not support that many APs in a single AP-Group. E. There are not enough AP licenses to support the additional quantity of APs. Real 76 Correct Answer: BD /Reference: : QUESTION 94 IEEE r provides support for which of the following: A. radio measurements within a WLAN B. radio measurement within an ESS C. fast roaming within an ESS

83 D. fast roaming within a BSS E. roaming across controllers Correct Answer: C /Reference: : QUESTION 95 If a Remote AP (RAP) is attempting to contact a controller that is behind a NAT device what protocol must be allowed through the NAT/Firewall? A. PAPI B. NATT C. IPSec D. SSH E. GRE Correct Answer: B /Reference: : QUESTION 96 Which of the following are NOT valid RAP forwarding modes? (Choose two) A. Tunnel B. Bridge C. Split-Tunnel D. Backup Real 77 E. Standard Correct Answer: DE

84 /Reference: : QUESTION 97 Which of the following are valid RAP operating modes? A. Always, Backup, Standard, Persistent B. Always, Backup, Tunnel, Persistent C. Always, Hotel-Connect, Tunnel, Standard D. Backup, Hotel-Connect, Standard, Persistent E. Backup, Normal, Tunnel, Always Correct Answer: A /Reference: best asnwer. QUESTION 98 When configuring split tunnel mode on a Remote AP (RAP) where is the routing function for the split tunnel defined? A. On the IP routing tab in the configuration screen. B. On the AP provisioning screen. C. In the RAP static routing tables D. In the Firewall policy E. In the RAP whitelist Correct Answer: D /Reference: : QUESTION 99 When does a RAP's backup SSID begin broadcasting?

85 A. When the GRE tunnel to the controller is established. B. When the IPSec tunnel to the controller is established. Real 78 C. When the controller cannot be reached with PAPI D. When bridging is required for guest users. E. When the controller cannot be reached with SSL Correct Answer: C /Reference: : QUESTION 100 A Remote AP provisioned in "Split-Tunnel" Forwarding mode has which characteristic? A. Local traffic first goes to the controller and is then spilt back to the local network. B. Traffic is IPSec encrypted before it is sent to the controller. C. The user role must have a "Permit" statement in order to locally bridge the traffic. D. The user role must have a "route dst-nat" statement to locally bridge the traffic. E. The RAP uses PAPI to send data traffic to the controller. Correct Answer: B /Reference: : QUESTION 101 A Remote AP was properly functioning before losing it's internet connection and now cannot communicate with the controller. What SSID is the AP broadcasting? A. The SSID in Operational mode Always and Forwarding mode Backup B. The SSID in Operational mode Split Tunnel and Forwarding mode Bridge C. The SSID in Operational mode Always and Forwarding mode Tunnel

86 D. The SSID in Operational mode Standard and Forwarding mode Tunnel E. The SSID in Operational mode Persistent and Forwarding mode Bridge Correct Answer: E /Reference: : QUESTION 102 A Remote AP provisioned with an SSID in "Bridged" forwarding mode has which one of the following characteristics? Real 79 A. The client obtains its IP address from the controller. B. The client's default gateway must be the controller. C. The client traffic is forwarded through a GRE tunnel to the controller. D. The client's default gateway may be the Access Point or a local gateway. E. The client's authentication must be 802.1X. Correct Answer: D /Reference: : QUESTION 103 An AP 105 was converted into a RAP. The RAP can authenticate its IPSec tunnel to a controller using which of the following methods? (Choose two) A X/EAP authentication B. Captive Portal authentication C. IP address authentication D. Username/Password authentication. E. Certificate/MAC address authentication. Correct Answer: DE

87 /Reference: : QUESTION 104 Which of the following describes a Remote AP provisioned in "Split-Tunnel" Forwarding mode? A. Local user traffic first goes to the controller and is then spilt back to the local network. B. All data and control traffic goes to the controller unsecured. C. The user role must have a "Permit" statement in order to locally bridge the traffic. D. The user role must have a "route src-nat" statement to locally bridge the traffic. E. The RAP uses PAPI to send data traffic to the controller. Correct Answer: D /Reference: selected answer is accurate. QUESTION 105 A Remote AP provisioned in "Split-Tunnel" Forwarding mode has which of the following Real 80 characteristics? A. Local traffic first goes to the controller and is then spilt back to the local network. B. User Traffic is CPSec encrypted before it is sent to the controller.

88 C. The user role must have a "Permit" statement in order to locally bridge the traffic. D. The user role must have a "permit dst-nat" statement to locally bridge the traffic. E. The RAP uses UDP 4500 to send traffic to the controller. Correct Answer: E /Reference: : QUESTION 106 What is the purpose of Mesh Clusters? A. To separate Mesh points from Mesh Portals. B. To ensure that mesh APs with the same VAPs are not in the same cluster. C. To define a group of mesh APs that create mesh links with each other. D. To cluster mesh APs of the same model together. E. To enable mesh APs to join the nearest mesh portal cluster. Correct Answer: C /Reference: : QUESTION 107 A company purchased an indoor mesh deployment using the 620 controller and the AP 105 models, where 5 APs will be deployed on a floor to provide wireless internet access for users. Users may open VPN tunnels using software clients over the wireless network to a 3rd party VPN concentrator overseas. The company wants to limit wireless user access to TCP traffic locally and VPN traffic overseas. In addition to the base AOS, which licenses will be necessary for this deployment? A. VPN, PEF-NG B. AP Capacity, PEF-NG C. AP Capacity, PEF-NG, VPN D. AP Capacity

89 E. PEF-NG, PEF-V Real 81 Correct Answer: B /Reference: appropriate answer. QUESTION 108 When deploying Remote Mesh Portals, what is one of the purposes of the Mesh Private VLAN? A. To separate wireless user traffic coming from mesh networks from non-mesh networks B. To tag mesh wireless user traffic on a particular AP C. To allow Mesh Points to form private vlan networks with certain users D. To tag control plane traffic from Mesh points to the controller E. To tag clients high priority traffic Correct Answer: D /Reference: : QUESTION 109 How does an Aruba infrastructure calculate a wireless device's location? A. GPS B. RF Fingerprinting C. RSSI triangulation D. TDOA E. LBS Correct Answer: C

90 /Reference: Real 82 QUESTION 110 Which dual radio access point models support concurrent operations in the 2.4Ghz band as well as the 5Ghz band? (Choose three) A. AP-92 B. AP-93 C. AP-105 D. AP-224 E. AP-135 Correct Answer: CDE /Reference: : Real 2 QUESTION 111 Which of the following APs do NOT support dual radio operations? (Choose two) A. AP 93 B. AP 105 C. RAP 3WN D. AP 224 E. AP 135 Correct Answer: AC /Reference: :

91 QUESTION 112 Centralized licensing is not in use on an Aruba based network which has a Master and three local controllers. No APs terminate on the Master controller. Roles and Firewall policies need to be created and applied, hence PEF-NG license is required On which controller should the license be installed? A. Only the master controller since role and firewall policies are created here. B. Only the local controllers since firewall policies are applied here C. The master and all three local controllers D. This isn't the correct license for this purpose, use PEF-VPN license E. This is not needed because PEF-NG is part of base OS Correct Answer: C /Reference: : QUESTION 113 What information do you need to generate a feature license key for an Aruba controller? A. The controller's MAC address and the feature description. B. Controller's MAC address and the certificate number C. Controller's Serial Number and the feature description D. Controller's Serial Number and the certificate number Real 3 E. Controller's MAC address and Serial Number Correct Answer: D /Reference: : QUESTION 114 What are the PEF-NG license limits based on?

92 A. Number of APs B. One license per controller C. Number of users D. Number of local controllers E. Master Controller total user count Correct Answer: A /Reference: suitable answer. QUESTION 115 Which of the following licenses are consumed by Mesh APs advertising an SSIDs? A. AP license B. Mesh license C. PEF-V license D. No license is required E. RAP License Correct Answer: A /Reference: : QUESTION 116 The permanent licenses on the controller will be deleted with the use of which command? A. Delete license B. Write erase C. Licenses cannot be deleted once activated Real 4 D. Write erase all

93 E. Reboot delete all Correct Answer: D /Reference: : QUESTION 117 A network administrator wants to terminate VPN sessions on a local controller in the DMZ. Which statement is true about the PEF-VPN license? A. It is only applied to the master controller B. It is only applied to the DMZ controller. C. It is based on the number of APs D. One license is needed on the master and the DMZ local E. It is distributed by the license server as needed Correct Answer: D /Reference: : QUESTION 118 Which of the following parameters can be specified in a rule for AP classification? (Choose three) A. SSID of an AP B. Number of clients connected to an AP. C. SNR of an AP.

94 D. Operating mode of an AP E. Discovering APs Correct Answer: ACE /Reference: : QUESTION 119 Which of the following functions can be configured in the Controller WIP wizard? (Choose three) A. Configure APs as Air Monitors B. Configure rules for AP classification. C. Configure preset levels for intrusion detection D. Blacklisting Rules for clients E. Identify encryption method used in your network. Correct Answer: BCE /Reference: : QUESTION 120 A client device associates with an SSID provisioned with 802.1X authentication. The client is set Real 71 for PEAP authentication. EAP termination (AAA Fastconnect) is disabled on the controller. But the client continuously cycles through the authentication process. Which of the following could cause this? (Choose two) A. The client is provisioned with the wrong EAP type. B. The client has an expired or revoked server certificate. C. The DHCP server is not enabled. D. The VLAN is missing for the SSID. E. The controller does not support PEAP in this mode.

95 Correct Answer: AB /Reference: : QUESTION 121 A client device associates with an SSID provisioned with 802.1X authentication. The client is set for LEAP authentication. EAP termination (AAA Fastconnect) is enabled on the controller. But the client continuously cycles through the authentication process. Which of the following could cause this? A. The Radius server is rejecting the client credentials. B. The client has an expired or revoked server certificate. C. The DHCP server is not enabled. D. The VLAN is missing for the SSID. E. The controller does not support LEAP in this mode. Correct Answer: E /Reference: accurate answer. QUESTION 122 A client attaches to a secure jack interface set to untrusted. But when the client tries to access the captive portal page, the following message appears, "Web Authentication is not enabled." What might be wrong? A. The client has the browser provisioned with proxy settings. B. The controller port needs to be set to trusted. C. A "aaa" profile needs to be selected on the Wired Access page. D. A Captive Portal profile needs to be assigned to the initial role. E. Web Authentication cannot be used in this way. Real 72 Correct Answer: D

96 /Reference: : QUESTION 123 Which command, when executed on a master controller, will show the APs connected to all controllers? A. show stm connectivity B. show ap active C. show ap database D. show ap bss-table E. show ap controller-lms Correct Answer: C /Reference: : QUESTION 124 Which of the following commands is most useful in showing the traffic of an individual user? A. show datapath session table B. show acl hits C. show rights D. show firewall E. show traffic client Correct Answer: A /Reference: : QUESTION 125 When direct consoled to an AP, what is the command sequence to factory default the AP and re- bootstrap?

97 A. setenv bootstat init B. setenv master init, boot C. purge, save, boot D. init, save, boot E. print, purge, boot Correct Answer: C /Reference: perfectly answered. QUESTION 126 What settings need to be changed on a factory default AP in order for it to use ADP to discover the Aruba Controller? A. DNS of the controller B. Static route C. AP group D. enable multicast E. no changes needed Correct Answer: E /Reference: : Real 43 QUESTION 127 As illustrated in the above diagram, a company has two campus locations and a building headquarters all located in different cities.

98 Following best practices, what would be the best way to construct mobility domains for the company? A. Buildings (1, 2) in one domain and Buildings (3, 4, 5, 6) in one domain B. Buildings (1, 2) in one domain, Building (3) in one domain, and Buildings (4, 5, 6) in one domain C. Buildings (1, 2, 4, 5, 6) in one domain and Building (3) in one domain D. Buildings (1, 2, 3, 4, 5, 6) in one domain E. Buildings (1) in one domain building (4) in one domain Correct Answer: B

99 /Reference: : QUESTION 128 When APs boot up, in which order do they discover a controller? A. DNS, DHCP, ADP multicast, ADP unicast, static B. static, DNS, DHCP, ADP broadcast, ADP multicast C. static, DHCP, ADP multicast, ADP broadcast, DNS D. static, DHCP, DNS, ADP multicast, ADP broadcast E. DNS, static, ADP multicast, ADP broadcast Correct Answer: C /Reference: : QUESTION 129 An AP is not communicating with the controller. Upon investigation you find that the AP is not discovering its controller through DNS. Instead, it received a DHCP reply with option 43 specifying the SIP server's IP address. How do you resolve this problem? A. Statically configure the AP to ignore Option 43 B. Remove the option 43 configuration on the DHCP server C. Statically configure the AP to only use DNS resolution and not other dynamic discovery methods D. After failing option 43 the AP should have proceeded with ADP, therefore the AP is faulty and needs to be replaced E. The AP should be purged Correct Answer: B /Reference: : QUESTION 130 How is an AP redirected to a Local controller after DNS resolution returns the Master's IP address?

100 A. Master looks at the AP-Group and CONTROLLER-IP attributes B. Master looks at the AP-Group and LMS-IP attributes C. In the AP-provisioning screen, the LMS-IP attribute must be set D. The AP must be statically configured to find the local controller E. In the AP-provisioning screen, set the CONTROLLER-IP attribute Real 48 Correct Answer: B /Reference: : QUESTION 131 An AP was configured and assigned to an AP group then powered off for over a week. When the AP is redeployed, what previous configuration will it retain? A. It's AP name and AP Group B. It's Serial Number C. The controller's IP address D. After a few days all configurations are lost E. The controller IP address and the AP Group Correct Answer: A /Reference: correct answer. QUESTION 132 A 3600 controller has 64 PEF-NG license, 128 AP licenses and 1 RFProtect license. How many AP's can terminate on the controller?

101 A. 1 Campus APs B. 64 Campus APs C. 128 Remote APs D. 256 Remote APs E. 512 Remote APs Correct Answer: A /Reference: : QUESTION 133 A 3200 controller has 16 AP licenses,16 PEF-NG licenses, 16 RFProtect licenses. There are 10 Campus APs terminating on the controller. How many remote AP's can terminate on the controller? A. 6 Real 49 B. 12 C. 16 D. 24 E. 32 Correct Answer: A /Reference:

102 : QUESTION 134 Centralized licensing is not enabled in a network of 1 Master and 2 Local controllers, what should be the license count on all controllers to terminate 8 APs on each Local controller and support Local redundancy? A. 16 AP license on all controllers B. 8 AP license on Master and 16 AP license on both locals C. 8 AP license on all controllers D. 1 AP license on Master and 16 AP license on both locals E. 16 AP licenses on the Locals Correct Answer: D /Reference: : QUESTION 135 An 7240 controller is Licensed for 560 APs. The controller has 500 Campus APs terminating on the controller. How many Remote APs can terminate on this controller? A. 12 B. 24 C. 48 D. 60 E. 120 Correct Answer: D /Reference: best answer. QUESTION 136 Real 50

103 An Aruba Controller is configured with VLAN 1,5, 200, and All VLANs have IP addresses assigned. Which is the default management VLAN on the Aruba controller? A. VLAN 5 B. VLAN 1 C. VLAN 200 D. None, it must be defined E. VLAN 4095 Correct Answer: B /Reference: : QUESTION 137 Which of the following statements is true? A. Aruba Campus APs must be physically attached to the Aruba Controller. B. Aruba Campus APs must be in the same broadcast domain as the Controller. C. Aruba Campus APs can be in different subnets from the Controller. D. Aruba Campus APs must be physically attached to the same Layer 3 switch. E. Aruba Campus APs can be connected directly to the public internet. Correct Answer: C /Reference: : QUESTION 138 Exhibit: Real 51

104 Referring to the diagram provided for this question, in which locations must you define the new data VLANs for wireless client traffic? (Choose two) A. in all L2 switches where an Aruba AP is physically connected B. in all APs and the L2 switches to which they are connected C. in the Aruba controller and the router it's connected to in an L2 deployment D. in the routers and switches where the APs are physically connected E. only on the Aruba controller in an L3 deployment Correct Answer: CE /Reference: : QUESTION 139 A controller is provisioned in L3 Mode for Wireless Users. What must be configured on the controller to enable DHCP requests to an external DHCP server?

105 A. an IP helper command B. the IP address of the DNS server C. the IP address of the APs D. the subnet address of the DHCP server E. the DHCP server IPSEC Key Correct Answer: A /Reference: : Real 52 QUESTION 140 Which parameter(s) does a Master controller use to determine where a provisioned AP should terminate its GRE tunnel? A. the IP address of the AP B. the MAC address of the AP C. the IP address of the switch nearest to the AP D. the name and group settings of the AP E. the VLAN the AP is attached to Correct Answer: D /Reference: : QUESTION 141 What is the best practice regarding licensing for a backup master to support Master Redundancy in a network without centralized licensing? A. Backup master only requires the AP license B. Supported limits and installed licenses should be the same on primary master and backup Master C. Licenses are pushed from the primary to the backup Master along with the configuration

106 D. The Backup Master does not require licenses to support master redundancy E. On the backup only one license of each typeis needed. Correct Answer: B /Reference: : QUESTION 142 Which of the following licenses can be included in the licensing pool for centralized licensing? (Choose three) Real 5 A. Factory default licenses B. PEFNG license C. Evaluation licenses D. RFProtect license E. PEFV license Correct Answer: BCD /Reference: : QUESTION 143 By default Centralized licensing messages between master controllers are sent. A. In the clear unencrypted B. Using CPSec C. Using IPSec site to site VPN tunnels D. Encrypted using GRE E. PAPI Correct Answer: A

107 /Reference: reliable answer. QUESTION 144 Which of the following will occur if a master license server fails with no standby server present? (Choose two) A. Local controllers licenses will continue to be valid for 30 days B. Local controllers will immediately remove all installed licenses C. No licenses will be sent to any new controllers that come online D. All licenses go back into the pool for redistribution E. A Local Controller elects itself master license server Correct Answer: AC /Reference: : QUESTION 145 Real 6 Which may be applied directly to an VLAN interface? (Choose three) A. Access List (ACL) B. Firewall Policy C. Roles D. AAA profiles

108 E. RF Plan Map Correct Answer: ABD /Reference: : QUESTION 146 When creating a firewall rule on an Aruba controller, which parameter is optional? A. Destination B. Service C. Source D. Log E. Action Correct Answer: D /Reference: : QUESTION 147 An administrator creates a WLAN with an unmodified default AAA profile. What is the default role the user is placed in? A. default-logon B. logon C. guest-logon D. default-ap E. AP-Role Correct Answer: B /Reference:

109 : Real 7 QUESTION 148 An Aruba based network has a Master and four local controllers deployed. But one of the locals, a new installation, is not seen by the Master. What might be wrong? (Choose two) A. PAPI is not enabled on the local controller. B. The master controller can only support three local controllers. C. IPSec is blocked by the internal network between the local and the master controllers. Real 73 D. The passphrase does not match on the master and local controllers. E. GRE is blocked between the master and local controllers. Correct Answer: CD /Reference: : QUESTION 149 Exhibit: Real 39