VLANs over IP Unnumbered SubInterfaces
|
|
|
- Aldous Rogers
- 5 years ago
- Views:
Transcription
1 The VLANs over IP Unnumbered Subinterfaces feature allows IP unnumbered interface support to be configured on Ethernet VLAN subinterfaces. This feature also provides support for DHCP on VLAN subinterfaces. Configuring Ethernet VLANs on IP unnumbered subinterfaces can save IPv4 address space and simplify configuration management, address management, and migration for DSL providers from ATM networks to IP. Finding Feature Information, page 1 Prerequisites for VLANs over IP Unnumbered Subinterfaces, page 1 Restrictions for VLANs over IP Unnumbered Subinterfaces, page 2 Information About VLANs over IP Unnumbered Subinterfaces, page 2 How to Configure VLANs over IP Unnumbered Subinterfaces, page 4 Configuration Examples for VLANs over IP Unnumbered Subinterfaces, page 7 Additional References for VLANs over IP Unnumbered Subinterfaces, page 7 Feature Information for VLANs over IP Unnumbered Subinterfaces, page 8 Finding Feature Information Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table. Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to An account on Cisco.com is not required. Prerequisites for VLANs over IP Unnumbered Subinterfaces Configure DHCP and ensure that it is operational. 1
2 Restrictions for VLANs over IP Unnumbered Subinterfaces Restrictions for VLANs over IP Unnumbered Subinterfaces Only Ethernet VLAN subinterfaces, in addition to serial interfaces, can be configured as IP unnumbered interfaces. Interface ranges (the interface range command) are not supported in Cisco IOS Release 12.2(18)SXE. Information About VLANs over IP Unnumbered Subinterfaces Support for VLANs over IP Unnumbered Subinterfaces The VLANs over IP Unnumbered Subinterfaces feature enables Ethernet VLANs to be configured on IP unnumbered subinterfaces. The IP unnumbered interface configuration enables IP processing on an interface without assigning an IP address to the interface. The IP unnumbered interface borrows an IP address from another interface that is already configured on the device to conserve network and address space. Figure 1 shows the implementation of the VLANs over IP Unnumbered Subinterfaces feature in a sample network topology. In this topology, the aggregation services routers dynamically establish IP routes when the DHCP server assigns IP addresses to hosts. Figure 1: Sample Network Topology Using VLANs over IP Unnumbered Subinterfaces Feature The VLANs over IP Unnumbered Subinterfaces feature supports the following functions: Allocating peer IP address through DHCP. Configuring IP unnumbered interface support for a range of VLAN subinterfaces. Configuring service selection gateway support for VLANs over IP unnumbered subinterfaces. Supporting DHCP relay agent information feature (Option 82). 2
3 DHCP Option 82 DHCP Option 82 DHCP provides a framework for passing configuration information to hosts on a TCP/IP network. Configuration parameters and other control information are carried in tagged data items (also called options) that are stored in the options field of the DHCP message. Option 82 is organized as a single DHCP option that contains information known by the relay agent. The DHCP Relay Agent Information feature communicates information to the DHCP server using a suboption of the DHCP relay agent information option called agent remote ID. The information sent in the agent remote ID includes an IP address identifying the relay agent and information about the interface and the connection over which the DHCP request was received. The DHCP server uses this information to assign IP addresses to interfaces and to form security policies. Figure 2 shows the agent remote ID suboption format that is used with the VLANs over IP Unnumbered Subinterfaces feature. Figure 2: Format of the Agent Remote ID Suboption Field Type Length Reserved NAS IP Address Interface Reserved VLAN ID Description Format type (1 byte). Value 2 specifies the format for use with this feature. Length of the agent remote ID suboption (1 byte). The type field and the remaining bytes of the length field are not included. Reserved (2 bytes). Network-attached storage (NAS) IP address (4 bytes) of the interface specified by the ip unnumbered command. Physical interface (1 byte). This field has the following format: slot (4 bits) module (1 bit) port (3 bits). For example, if the interface is Ethernet 2/1/1, the slot is 2, the module is 1, and the port is 1. Reserved (1 byte). VLAN identifier (2 bytes) for the Ethernet subinterface. 3
4 Benefits of VLANs over IP Unnumbered Subinterfaces Benefits of VLANs over IP Unnumbered Subinterfaces The VLANs over IP Unnumbered Subinterfaces feature provides the following benefits: Migration from other interfaces to Gigabit Ethernet uplinks and IP core becomes easier for DSL providers. All ports share the same subnet, therefore saving the IPv4 address space. Each user is on a separate VLAN. DHCP communicates routing information, and there is no Address Resolution Protocol (ARP) or MAC address spoofing, which leads to enhancement in security layers. IP address management with DHCP becomes simpler. Configuring interface ranges with Ethernet VLAN subinterfaces leads to easier NVRAM configuration and saves overall memory. How to Configure VLANs over IP Unnumbered Subinterfaces Configuring IP Unnumbered Interface Support on an Ethernet VLAN Subinterface SUMMARY STEPS 1. enable 2. configure terminal 3. interface type number [name-tag] 4. encapsulation dot1q vlan-id [native] 5. ip unnumbered type number 6. end 7. show running-config DETAILED STEPS Step 1 Step 2 Command or Action enable Device> enable configure terminal Purpose Enables privileged EXEC mode. Enter your password if prompted. Enters global configuration mode. Device# configure terminal 4
![Configuring IP Unnumbered Interface Support on a Range of Ethernet VLAN Subinterfaces Step 3 Step 4 Step 5 Command or Action interface type number [name-tag] Device(config)# interface fastethernet](/docs-images/89/98684715/images/5-0.jpg "1/0.1 encapsulation dot1q vlan-id [native] Device(config-subif)# encapsulation dot1q 10 ip unnumbered type number Device(config-subif)# ip unnumbered ethernet 3/0 Purpose Configures an interface type")
5 Configuring IP Unnumbered Interface Support on a Range of Ethernet VLAN Subinterfaces Step 3 Step 4 Step 5 Command or Action interface type number [name-tag] Device(config)# interface fastethernet 1/0.1 encapsulation dot1q vlan-id [native] Device(config-subif)# encapsulation dot1q 10 ip unnumbered type number Device(config-subif)# ip unnumbered ethernet 3/0 Purpose Configures an interface type and enters interface or subinterface configuration mode. Enables IEEE 802.1Q encapsulation of traffic on a specified subinterface in a VLAN. Enables IP processing on an interface without assigning an explicit IP address to the interface. The type and number arguments specify an interface with a predefined IP address on the device. Do not specify an unnumbered interface, if one already exists. Step 6 Step 7 end Device(config-subif)# end show running-config Device# show running-config Exits subinterface configuration mode and returns to privileged EXEC mode. Displays contents of the current running configuration file on the device including the configuration of the IP unnumbered support feature. Configuring IP Unnumbered Interface Support on a Range of Ethernet VLAN Subinterfaces Note The interface range command is not supported in Cisco IOS Release 12.2(18)SXE. 5
6 Configuring IP Unnumbered Interface Support on a Range of Ethernet VLAN Subinterfaces SUMMARY STEPS 1. enable 2. configure terminal 3. interface range {{ethernet fastethernet gigabitethernet vlan vlan} slot/interface.subinterface - {ethernet fastethernet gigabitethernet vlan vlan} slot/interface.subinterface macro macro-name} 4. encapsulation dot1q vlan-id [native] 5. ip unnumbered type number 6. end 7. show running-config DETAILED STEPS Step 1 Step 2 Command or Action enable Device> enable configure terminal Purpose Enables privileged EXEC mode. Enter your password if prompted. Enters global configuration mode. Step 3 Step 4 Device# configure terminal interface range {{ethernet fastethernet gigabitethernet vlan vlan} slot/interface.subinterface - {ethernet fastethernet gigabitethernet vlan vlan} slot/interface.subinterface macro macro-name} Device(config)# interface range fastethernet 1/0.1 - fastethernet 1/0.100 encapsulation dot1q vlan-id [native] Executes commands on multiple subinterfaces simultaneously. The device prompt changes to configuration interface range mode after the commands are executed. Separate the interface range with a hyphen and space as shown in the example. Applies a unique VLAN ID to each subinterface within the range. Device(config-if-range)# encapsulation dot1q 10 The VLAN ID specified by the vlan-id argument is applied to the first subinterface in the range. Each subsequent interface is assigned a VLAN ID, which is the specified vlan-id including the subinterface number and excluding the first subinterface number (VLAN ID + subinterface number - first subinterface number). Step 5 ip unnumbered type number Device(config-if-range)# ip unnumbered ethernet 3/0 Enables IP processing on an interface without assigning an explicit IP address to the interface. The type and number arguments specify an interface with a predefined IP address on the device. Do not specify an unnumbered interface, if one already exists. 6
7 Configuration Examples for VLANs over IP Unnumbered Subinterfaces Command or Action Purpose Step 6 Step 7 end Device(config-if-range)# end show running-config Device# show running-config Exits interface-range configuration mode and returns to privileged EXEC mode. Displays contents of the current running configuration file on the device including the configuration of the IP unnumbered support feature. Configuration Examples for VLANs over IP Unnumbered Subinterfaces VLAN Configuration on a Single IP Unnumbered Subinterface The following example shows how to configure IP unnumbered subinterface using Ethernet VLAN subinterface 3/0.2: interface ethernet 3/0.2 encapsulation dot1q 200 ip unnumbered ethernet 3/1 VLAN Configuration on a Range of IP Unnumbered Subinterfaces The following example shows how to configure IP unnumbered subinterfaces using Fast Ethernet subinterfaces in the range from 5/1.1 to 5/1.4: interface range fastethernet 5/1.1 - fastethernet 5/1.4 ip unnumbered ethernet 3/1 Additional References for VLANs over IP Unnumbered Subinterfaces Related Documents Related Topic Cisco IOS commands Document Title Cisco IOS Master Command List, All Releases 7
8 Feature Information for VLANs over IP Unnumbered Subinterfaces Related Topic IP Addressing commands IP Addressing Services configuration tasks VLAN configuration tasks VLAN configuration commands Document Title Cisco IOS IP Addressing Services Command Reference Cisco IOS IP Addressing Services Configuration Guide Cisco IOS LAN Switching Configuration Guide Cisco IOS LAN Switching Command Reference RFCs RFCs RFC 1812 Title Requirements for IP Version 4 Routers, June 1995 Technical Assistance Description The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. Link Feature Information for VLANs over IP Unnumbered Subinterfaces The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature. 8
9 Feature Information for VLANs over IP Unnumbered Subinterfaces Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to An account on Cisco.com is not required. Table 1: Feature Information for VLANs over IP Unnumbered Subinterfaces Feature Name VLANs over IP Unnumbered Subinterfaces Releases Cisco IOS XE Release 3.9S Feature Information The VLANs over IP Unnumbered Subinterfaces feature allows IP unnumbered interface support to be configured on Ethernet VLAN subinterfaces. This feature also provides support for DHCP on VLAN subinterfaces. Configuring Ethernet VLANs on IP unnumbered subinterfaces can save IPv4 address space and simplify configuration management, address management, and migration for DSL providers from ATM networks to IP. The following command was modified: ip unnumbered 9
10 Feature Information for VLANs over IP Unnumbered Subinterfaces 10
Configuring IP Unnumbered on IEEE 802.1Q VLANs
CHAPTER 7 Configuring IP Unnumbered on IEEE 802.1Q VLANs Service providers continuously seek ways in which they can make their networks less complex and less expensive, and reduce the cost of provisioning
Configuring IP Unnumbered Interface
CHAPTER 14 This chapter discusses the IP Unnumbered Interface feature, which allows you to enable IP processing on an interface without assigning an explicit IP address. This chapter contains these sections:
DHCP Client. Finding Feature Information. Restrictions for the DHCP Client
The Cisco Dynamic Host Configuration Protocol (DHCP) Client feature allows a Cisco device to act as a host requesting configuration parameters, such as an IP address, from a DHCP server. Finding Feature
DHCP Relay Server ID Override and Link Selection Option 82 Suboptions
DHCP Relay Server ID Override and Link Selection Option 82 Suboptions The DHCP Relay Server ID Override and Link Selection Option 82 Suboptions feature enables the relay agent to be part of all Dynamic
Configuring the Cisco IOS DHCP Relay Agent
All Cisco devices that run Cisco software include a DHCP server and the relay agent software. A DHCP relay agent is any host or IP device that forwards DHCP packets between clients and servers. This module
VLAN Range. Feature Overview
VLAN Range Feature History Release 12.0(7)XE 12.1(5)T 12.2(2)DD 12.2(4)B 12.2(8)T 12.2(13)T Modification The interface range command was introduced. The interface range command was integrated into Cisco
DHCP Server RADIUS Proxy
The Dynamic Host Configuration Protocol (DHCP) Server RADIUS Proxy is a RADIUS-based address assignment mechanism in which a DHCP server authorizes remote clients and allocates addresses based on replies
Match-in-VRF Support for NAT
The feature supports Network Address Translation (NAT) of packets that communicate between two hosts within the same VPN routing and forwarding (VRF) instance. In intra-vpn NAT, both the local and global
Using Flexible NetFlow Flow Sampling
This document contains information about and instructions for configuring sampling to reduce the CPU overhead of analyzing traffic with Flexible NetFlow. NetFlow is a Cisco technology that provides statistics
Using Flexible NetFlow Flow Sampling
This document contains information about and instructions for configuring sampling to reduce the CPU overhead of analyzing traffic with Flexible NetFlow. NetFlow is a Cisco technology that provides statistics
VLAN Range. Feature Overview
VLAN Range Feature History Release 12.0(7)XE 12.1(5)T 12.2(2)DD Modification The interface range command was introduced. The interface range command was integrated into Cisco IOS Release 12.1(5)T. The
DHCPv6 Individual Address Assignment
The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) Individual Address Assignment feature manages nonduplicate address assignment in the correct prefix based on the network where the host is connected.
Add Path Support in EIGRP
The feature enables hubs in a single Dynamic Multipoint VPN (DMVPN) domain to advertise multiple best paths to connected spokes when the Enhanced Interior Gateway Routing Protocol (EIGRP) is the routing
PPPoE Agent Remote-ID and DSL Line Characteristics Enhancement
PPPoE Agent Remote-ID and DSL Line Characteristics Enhancement The PPPoE Agent Remote-ID and DSL Line Characteristics Enhancement feature provides a method by which the digital subscriber line access multiplexer
Flow-Based per Port-Channel Load Balancing
The feature allows different flows of traffic over a Gigabit EtherChannel (GEC) interface to be identified based on the packet header and then mapped to the different member links of the port channel.
IGMP Proxy. Finding Feature Information. Prerequisites for IGMP Proxy
This module describes how to configure IGMP proxy to enable a device to send an IGMP report to a specified destination IP address. Finding Feature Information, page 1 Prerequisites for, page 1 Information
EIGRP Route Tag Enhancements
The feature enables you to specify and display route tags in dotted-decimal format, filter routes using the route tag value with wildcard mask, and set a default route tag for all internal Enhanced Interior
Providing Connectivity Using ATM Routed Bridge Encapsulation over PVCs
Providing Connectivity Using ATM Routed Bridge Encapsulation over PVCs Last Updated: December 5, 2011 The Providing Connectivity Using ATM Routed Bridge Encapsulation over PVCs feature provides the functionality
Remote Access MPLS-VPNs
First Published: August 12, 2002 Last Updated: May 4, 2009 The feature allows the service provider to offer a scalable end-to-end Virtual Private Network (VPN) service to remote users. This feature integrates
Configuring DHCP Option 60 and Option 82 with VPN-ID Support for Transparent Automatic Logon
Configuring DHCP Option 60 and Option 82 with VPN-ID Support for Transparent Automatic Logon Intelligent Services Gateway (ISG) is a Cisco software feature set that provides a structured framework in which
DHCPv6Relay LightweightDHCPv6RelayAgent
DHCPv6Relay LightweightDHCPv6RelayAgent The DHCPv6 Relay Lightweight DHCPv6 Relay Agent feature allows relay agent information to be inserted by an access node that performs a link-layer bridging (non-routing)
Cisco Discovery Protocol Version 2
Cisco Discovery Protocol (formerly known as CDP) is a Layer 2, media-independent, and network-independent protocol that runs on Cisco devices and enables networking applications to learn about directly
DHCPv6Relay LightweightDHCPv6RelayAgent
DHCPv6Relay LightweightDHCPv6RelayAgent The DHCPv6 Relay Lightweight DHCPv6 Relay Agent feature allows relay agent information to be inserted by an access node that performs a link-layer bridging (non-routing)
MPLS over GRE. Finding Feature Information. Prerequisites for MPLS VPN L3VPN over GRE
The feature provides a mechanism for tunneling Multiprotocol Label Switching (MPLS) packets over a non-mpls network. This feature utilizes MPLS over generic routing encapsulation (MPLSoGRE) to encapsulate
Providing Connectivity Using ATM Routed Bridge Encapsulation over PVCs
Providing Connectivity Using ATM Routed Bridge Encapsulation over PVCs First Published: May 2, 2005 Last Updated: November 24, 2010 The Providing Connectivity Using ATM Routed Bridge Encapsulation over
Static NAT Mapping with HSRP
This module contains procedures for configuring Network Address Translation (NAT) to support the increasing need for highly resilient IP networks. This network resiliency is required where application
Cisco Discovery Protocol Version 2
Cisco Discovery Protocol (formerly known as CDP) is a Layer 2, media-independent, and network-independent protocol that runs on Cisco devices and enables networking applications to learn about directly
Fine-Grain NBAR for Selective Applications
By default NBAR operates in the fine-grain mode, offering NBAR's full application recognition capabilities. Used when per-packet reporting is required, fine-grain mode offers a troubleshooting advantage.
Ethernet Overhead Accounting
The feature enables the router to account for downstream Ethernet frame headers when applying shaping to packets. Finding Feature Information, page 1 Restrictions for, page 1 Information About, page 2
NAT Routemaps Outside-to-Inside Support
The feature enables you to configure a NAT routemap configuration that allows IP sessions to be initiated from outside the network to inside the network. This module explains how to configure the feature.
BGP Named Community Lists
The feature allows the network operator to assign meaningful names to community lists and increases the number of community lists that can be configured. Finding Feature Information, page 1 Information
Configuring Easy Virtual Network Shared Services
Configuring Easy Virtual Network Shared Services This chapter describes how to use route replication and redistribution to share services in an Easy Virtual Network (EVN). Finding Feature Information,
Finding Feature Information
The feature provides PPP over Ethernet (PPPoE) client support on routers. PPPoE is a commonly used application in the deployment of digital subscriber lines (DSLs). The PPP over Ethernet Client feature
IEEE 802.1X Open Authentication
allows a host to have network access without having to go through IEEE 802.1X authentication. Open authentication is useful in an applications such as the Preboot Execution Environment (PXE), where a device
BGP Route-Map Continue
The feature introduces the continue clause to BGP route-map configuration. The continue clause allows for more programmable policy configuration and route filtering and introduces the capability to execute
QoS Group Match and Set for Classification and Marking
QoS Group Match and Set for Classification and Marking This feature provides the capability of matching and classifying traffic on the basis of the QoS group value. Finding Feature Information, on page
IPv6 Snooping. Finding Feature Information. Restrictions for IPv6 Snooping
The feature bundles several Layer 2 IPv6 first-hop security features, including IPv6 neighbor discovery inspection, IPv6 device tracking, IPv6 address glean, and IPv6 binding table recovery, to provide
FPG Endpoint Agnostic Port Allocation
When the Endpoint Agnostic Port Allocation feature is configured, an entry is added to the Symmetric Port Database. If the entry is already available, the port listed in the Symmetric Port Database is
Port-Shaper and LLQ in the Presence of EFPs
The feature allows network designers to configure port and class policies on ports that contain Ethernet Flow Points (EFPs). These policies support Low Latency Queueing (LLQ) and traffic prioritization
Configuring DHCP Services for Accounting and Security
Configuring DHCP Services for Accounting and Security Cisco IOS XE software supports several capabilities that enhance DHCP security, reliability, and accounting in Public Wireless LANs (PWLANs). This
QoS Policy Propagation via BGP
The feature allows you to classify packets by IP precedence based on the Border Gateway Protocol (BGP) community lists, BGP autonomous system paths, and access lists. After packets have been classified,
Flexible NetFlow - MPLS Support
The feature supports the monitoring of the following MPLS-related fields: MPLS Labels 1-6 (3 bytes -- 20 bits of label, 3 bits of EXP, 1 bit of EOS). Top Label EXP i.e. the EXP field for label 1. Top Label
Configuring DHCP. Finding Feature Information. Information About DHCP. DHCP Server. DHCP Relay Agent
Finding Feature Information, page 1 Information About DHCP, page 1 How to Configure DHCP Features, page 8 Server Port-Based Address Allocation, page 17 Finding Feature Information Your software release
IPv6 Access Services: DHCPv6 Relay Agent
A Dynamic Host Configuration Protocol for IPv6 (DHCPv6) relay agent, which may reside on the client's link, is used to relay messages between the client and the server. Finding Feature Information, page
Port-Level Shaping and Minimum Bandwidth Guarantee
Port-Level Shaping and Minimum Bandwidth Guarantee This document explains the Port-Level Shaping and Minimum Bandwidth Guarantee feature. The port-level shaping part of this feature allows you to configure
N:1 PVC Mapping to PWE with Nonunique VPIs
N:1 PVC Mapping to PWE with Nonunique VPIs The N:1 PVC Mapping to PseudoWire Emulation (PWE) with Nonunique virtual path identifiers (VPIs) feature maps one or more ATM permanent virtual circuits (PVCs)
IEEE 802.1X Multiple Authentication
The feature provides a means of authenticating multiple hosts on a single port. With both 802.1X and non-802.1x devices, multiple hosts can be authenticated using different methods. Each host is individually
Configuring DHCP. Information About DHCP. DHCP Server. DHCP Relay Agent. DHCP Snooping
Information About DHCP DHCP Server DHCP Relay Agent DHCP Snooping Information About DHCP, on page 1 How to Configure DHCP Features, on page 7 Server Port-Based Address Allocation, on page 13 Feature Information
PPP over Frame Relay
The feature allows a router to establish end-to-end Point-to-Point Protocol (PPP) sessions over Frame Relay. Finding Feature Information, page 1 Prerequisites for, page 1 Restrictions for, page 2 Information
IEEE 802.1Q-in-Q VLAN Tag Termination
IEEE 802.1Q-in-Q VLAN Tag Termination Encapsulating IEEE 802.1Q VLAN tags within 802.1Q enables service providers to use a single VLAN to support customers who have multiple VLANs. The IEEE 802.1Q-in-Q
Extended NAS-Port-Type and NAS-Port Support
Extended NAS-Port-Type and NAS-Port Support Last Updated: April 18, 2012 The Extended NAS-Port-Type and NAS-Port Support feature allows you to identify what service type is taking place on specific ports
Fine-Grain NBAR for Selective Applications
By default NBAR operates in the fine-grain mode, offering NBAR's full application recognition capabilities. Used when per-packet reporting is required, fine-grain mode offers a troubleshooting advantage.
IP over IPv6 Tunnels. Information About IP over IPv6 Tunnels. GRE IPv4 Tunnel Support for IPv6 Traffic
IPv6 supports IP over IPv6 tunnels, which includes the following: Generic routing encapsulation (GRE) IPv4 tunnel support for IPv6 traffic IPv6 traffic can be carried over IPv4 GRE tunnels using the standard
IS-IS Inbound Filtering
The Intermediate System-to-Intermediate System (IS-IS) Inbound Filtering feature prevents unwanted IS-IS routes from being installed in a routing table. A user can deny or permit a route from being installed
EIGRP Stub Routing. Finding Feature Information. Information About EIGRP Stub Routing. EIGRP Stub Routing
The EIGRP stub routing feature improves network stability, reduces resource utilization, and simplifies the stub device configuration. Stub routing is commonly used in hub-and-spoke network topologies.
Configuring DHCP. Finding Feature Information. Information About DHCP. DHCP Server. DHCP Relay Agent
Finding Feature Information, on page 1 Information About DHCP, on page 1 How to Configure DHCP Features, on page 8 Server Port-Based Address Allocation, on page 17 Finding Feature Information Your software
BGP-MVPN SAFI 129 IPv6
Subsequent Address Family Identifier (SAFI) 129, known as VPN Multicast SAFI, provides the capability to support multicast routing in the service provider's core IPv6 network. Border Gateway Protocol (BGP)
Configuring VLANs. Finding Feature Information. Prerequisites for VLANs
Finding Feature Information, page 1 Prerequisites for VLANs, page 1 Restrictions for VLANs, page 2 Information About VLANs, page 2 How to Configure VLANs, page 8 Monitoring VLANs, page 22 Where to Go Next,
Flexible NetFlow Full Flow support
Flexible NetFlow Full Flow support Last Updated: January 29, 2013 The Flexible NetFlow - Full Flow support feature enables Flexible NetFlow to collect flow records for every packet. Finding Feature Information,
BFD on BDI Interfaces
The Cisco feature alleviates limitations on the maximum number of interfaces per system that switched virtual interfaces (SVI) impose. This document describes how to configure the Bidirectional Forwarding
802.1P CoS Bit Set for PPP and PPPoE Control Frames
802.1P CoS Bit Set for PPP and PPPoE Control The 802.1P CoS Bit Set for PPP and PPPoE Control feature provides the ability to set user priority bits in the IEEE 802.1Q tagged frame to allow traffic prioritization.
Configuring DHCP. Finding Feature Information. Information About DHCP. DHCP Server. DHCP Relay Agent
Finding Feature Information, page 1 Information About DHCP, page 1 How to Configure DHCP Features, page 8 Server Port-Based Address Allocation, page 18 Finding Feature Information Your software release
Configuring DHCP. Finding Feature Information. Information About DHCP. DHCP Server. DHCP Relay Agent
Finding Feature Information, page 1 Information About DHCP, page 1 How to Configure DHCP Features, page 8 Server Port-Based Address Allocation, page 18 Finding Feature Information Your software release
VRRPv3 Protocol Support
Virtual Router Redundancy Protocol (VRRP) enables a group of routers to form a single virtual router to provide redundancy. The LAN clients can then be configured with the virtual router as their default
Multiprotocol Label Switching (MPLS) on Cisco Routers
Multiprotocol Label Switching (MPLS) on Cisco Routers This document describes commands for configuring and monitoring Multiprotocol Label Switching (MPLS) functionality on Cisco routers and switches. This
NBAR2 HTTP-Based Visibility Dashboard
The NBAR2 HTTP-based Visibility Dashboard provides a web interface displaying network traffic data and related information. The information is presented in an intuitive, interactive graphical format. Finding
BGP mvpn BGP safi IPv4
The BGP mvpn BGP safi 129 IPv4 feature provides the capability to support multicast routing in the service provider s core IPv4 network This feature is needed to support BGP-based MVPNs BGP MVPN provides
Configuring the Physical Subscriber Line for RADIUS Access and Accounting
Configuring the Physical Subscriber Line for RADIUS Access and Accounting Configuring a physical subscriber line for RADIUS Access and Accounting enables an L2TP access concentrator (LAC) and an L2TP network
OSPF Limit on Number of Redistributed Routes
Open Shortest Path First (OSPF) supports a user-defined maximum number of prefixes (routes) that are allowed to be redistributed into OSPF from other protocols or other OSPF processes. Such a limit could
RADIUS Route Download
The feature allows users to configure their network access server (NAS) to direct RADIUS authorization. Finding Feature Information, page 1 Prerequisites for, page 1 Information About, page 1 How to Configure,
PPPoE on ATM. Finding Feature Information. Prerequisites for PPPoE on ATM. Restrictions for PPPoE on ATM
This feature module describes the PPP over Ethernet (PPPoE) on ATM feature. The feature provides the ability to connect a network of hosts over a simple bridging-access device to a remote access concentrator.
Configuring the Cisco IOS XE DHCP Server
Configuring the Cisco IOS XE DHCP Server Last Updated: December 20, 2011 Cisco routers running Cisco IOS XE software include Dynamic Host Configuration Protocol (DHCP) server and relay agent software.
Network Edge Authentication Topology
The Network Edge Access Topology (NEAT) feature enables extended secure access in areas outside the wiring closet (such as conference rooms). This secure access allows any type of device to authenticate
IP Multicast Optimization: IGMP State Limit
Finding Feature Information, page 1 Prerequisites for IGMP State Limit, page 1 Restrictions for IGMP State Limit, page 2 Information About IGMP State Limit, page 2 How to Configure IGMP State Limit, page
Nested Class Map Support for Zone-Based Policy Firewall
Nested Class Map Support for Zone-Based Policy Firewall The Nested Class Map Support for Zone-Based Policy Firewall feature provides the Cisco IOS XE firewall the functionality to configure multiple traffic
IPv6 First-Hop Security Binding Table
IPv6 First-Hop Security Binding Table Last Updated: July 25, 2012 A database table of IPv6 neighbors connected to a device is created from information sources such as Neighbor Discovery Protocol (NDP)
Configurable Number of Simultaneous Packets per Flow
Configurable Number of Simultaneous Packets per Flow In zone-based policy firewalls, the number of simultaneous packets per flow is restricted to 25 and packets that exceed the limit are dropped. The dropping
BGP Event-Based VPN Import
The feature introduces a modification to the existing Border Gateway Protocol (BGP) path import process. The enhanced BGP path import is driven by events; when a BGP path changes, all of its imported copies
Sun RPC ALG Support for Firewalls and NAT
The feature adds support for the Sun Microsystems remote-procedure call (RPC) application-level gateway (ALG) on the firewall and Network Address Translation (NAT). Sun RPC is an application layer protocol
Sun RPC ALG Support for Firewalls and NAT
The feature adds support for the Sun Microsystems remote-procedure call (RPC) application-level gateway (ALG) on the firewall and Network Address Translation (NAT). Sun RPC is an application layer protocol
Regulating Packet Flow on a Per-Interface Basis Using Generic Traffic Shaping
Regulating Packet Flow on a Per-Interface Basis Using Generic Traffic Shaping Packet flow on a network can be regulated using a traffic shaping mechanism. One such traffic shaping mechanism is a Cisco
Configuring Private VLANs
Finding Feature Information, on page 1 Prerequisites for Private VLANs, on page 1 Restrictions for Private VLANs, on page 1 Information About Private VLANs, on page 2 How to Configure Private VLANs, on
Configuring System MTU
Restrictions for System MTU, on page 1 Information About the MTU, on page 1 How to Configure MTU, on page 2 Configuration Examples for System MTU, on page 4 Additional References for System MTU, on page
OSPFv2 Cryptographic Authentication
To prevent unauthorized or invalid routing updates in your network, Open Shortest Path First version 2 (OSPFv2) protocol packets must be authenticated. There are two methods of authentication that are
Configuring DHCP Features
This chapter describes how to configure DHCP snooping and option-82 data insertion on the Cisco ASR 920 Series Router. Finding Feature Information, page 1 Limitations and Restrictions, page 1 DHCP Features,
Flexible NetFlow IPFIX Export Format
The feature enables sending export packets using the IPFIX export protocol. The export of extracted fields from NBAR is only supported over IPFIX. Finding Feature Information, page 1 Information About,
ibgp Multipath Load Sharing
This feature module describes the feature. This feature enables the BGP speaking router to select multiple ibgp paths as the best paths to a destination. The best paths or multipaths are then installed
Autosense for ATM PVCs and MUX SNAP Encapsulation
Autosense for ATM PVCs and MUX SNAP Encapsulation The PPPoA/PPPoE Autosense for ATM PVCs feature enables a router to distinguish between incoming PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) over
Constraining IP Multicast in a Switched Ethernet Network
Constraining IP Multicast in a Switched Ethernet Network This module describes how to configure devices to use the Cisco Group Management Protocol (CGMP) in switched Ethernet networks to control multicast
Switches running the LAN Base feature set support only static routing on SVIs.
Finding Feature Information, on page 1 Prerequisites for VLANs, on page 1 Restrictions for VLANs, on page 2 Information About VLANs, on page 2 How to Configure VLANs, on page 6 Monitoring VLANs, on page
Bulk Logging and Port Block Allocation
The feature allocates a block of ports for translation instead of allocating individual ports. This feature is supported only in carrier-grade Network Address Translation (CGN) mode. This module provides
DHCP Server Port-Based Address Allocation
The feature provides port-based address allocation support on the Cisco IOS Dynamic Host Configuration Protocol (DHCP) server for the Ethernet platform. The DHCP server provides address assignment support
Flexible NetFlow IPv6 Unicast Flows
The feature enables Flexible NetFlow to monitor IPv6 traffic. Finding Feature Information, page 1 Information About Flexible NetFlow IPv6 Unicast Flows, page 1 How to Configure Flexible NetFlow IPv6 Unicast
Set Inner CoS Bits for QinQ
Set Inner CoS Bits for QinQ First Published: September 2007 Revised: August 2008 This document describes the Set Inner CoS Bits for QinQ feature that allows you to mark both inner and outer VLAN tags of
IPv6 Snooping. Finding Feature Information. Restrictions for IPv6 Snooping
The feature bundles several Layer 2 IPv6 first-hop security features, including IPv6 neighbor discovery inspection, IPv6 device tracking, IPv6 address glean, and IPv6 binding table recovery, to provide
IPv6 Access Services: DHCPv6 Prefix Delegation
The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) prefix delegation feature can be used to manage link, subnet, and site addressing changes. Finding Feature Information, page 1 Information About,
Web Services Management Agent Configuration Guide, Cisco IOS XE Release 3S
Web Services Management Agent Configuration Guide, Cisco IOS XE Release 3S First Published: March 29, 2013 Last Modified: March 29, 2013 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive
EVC Quality of Service
This document contains information about how to enable quality of service (QoS) features (such as traffic classification and traffic policing) for use on an Ethernet virtual circuit (EVC). An EVC as defined
Flexible NetFlow IPv4 Unicast Flows
The Flexible Netflow IPv4 Unicast Flows feature enables Flexible NetFlow to monitor IPv4 traffic. Finding Feature Information, page 1 Information About Flexible NetFlow IPv4 Unicast Flows, page 1 How to
QoS Tunnel Marking for GRE Tunnels
The feature introduces the capability to define and control the quality of service (QoS) for both incoming and outgoing customer traffic on the provider edge (PE) router in a service provider network.