ES-562/564U COMBINATION CLOCK/TIMER

Size: px
Start display at page:

Download "ES-562/564U COMBINATION CLOCK/TIMER"

Transcription

1 142 SIERRA ST., EL SEGUNDO, CA USA (310) FAX (310) ES-562/564U COMBINATION CLOCK/TIMER OPERATION AND MAINTENANCE MANUAL The ES-562U/564U is a combination six digit time-of-day Clock / 100 Hour Up/Down Timer. The ES-562U Clock displays time in 12-hour format; the ES-564U Clock displays time in 24-hour format. The clock and timer modes operate independently Clock and Timer operations do not affect each other. When the unit is powered up it is in Clock mode. Five control switches are provided, accessible on the top of the case (standard) or on the front panel (option P). The functions are TIMER, UP/DOWN, SET/STOP, SELECT/RESET and CLOCK. Momentarily activating the CLOCK or TIMER function will latch the unit into the selected mode, displaying the CLOCK or TIMER data on the.56 yellow LED display. The other three switches are mode-dependent. Setting the Clock is accomplished by holding down the CLOCK button and using the SET and SELECT buttons. Hold the CLOCK button down and press the SELECT button. This causes the Hours-digits to flash and allows them to be set by pressing the SET button until the hours agree with the time being set. Continue holding the CLOCK button down and press the SELECT button again, enabling the Minutesdigits to be set in the same manner. The same procedure applies for setting the Seconds-digits and they should be set slightly ahead of real time. (Seconds are synchronized after the Calendar is set.) Set the Calendar to the correct date in the same manner. The Calendar should be set to the correct date because the units automatically correct for daylight savings time. To turn this feature off, refer to the layout on page 6. Month is set first, followed by day and then year. After the date is set, press the SELECT button one more time to stop the digits from flashing. At this time, the seconds can be synchronized to real time by pressing and holding the CLOCK and SET buttons until real time matches the time set on the display. When the SET button is released, the unit begins counting from that point. Errors made during the setting procedure can easily be corrected by selecting the digit-pairs in need of correction. Set them, as above, by pressing the SET button until the proper number is displayed. Continue selecting until all digits are stable (not flashing). The TIMER can be preset in a similar fashion. Press and release the TIMER button. If the TIMER is counting, press the SET/STOP button to stop it. The timer is preset just like the CLOCK, except that the TIMER button needs to be continuously pressed while setting. In order to store a manually preset time in memory, either the UP button or the DOWN button must be pressed after setting the timer to the desired preset time. The UP/DOWN switch starts the TIMER counting up or down. The SET/STOP button, if pressed alone, stops the TIMER. The SELECT/RESET switch, if pushed alone, acts as a reset/preset switch. The first time it is pressed, the timer is reset to 00:00:00. If pressed again (within 5 seconds) the timer is set to the last manually preset time. If the timer was counting up or down before being reset, it continues to count in the same direction. If the unit is ordered with option R, remote control inputs are provided on a rear-mounted 9-pin connector. A short to ground is required to activate the desired function. The optional relay contact closure on the Hour or Hour & Half-Hour is also accessible on the connector. The contacts are rated at 10 watts maximum resistive load, 500 ma maximum switching current. SPECIFICATIONS Electrical: Mechanical: Input Voltage 117 VAC, 50/60 Hz, 5 watts max. Etched Aluminum case 2.5 High x 8 Wide x 6 Deep Page 1 of 7

2 Page 2 OPTIONS C - D - HR - J - P - P2 - Q - When this option (Crystal Timebase) is specified, a trimmer is included for greater accuracy. The crystal (.002% accuracy) is factory calibrated to provide an accuracy of 2-3 seconds per week and can also be field adjusted for greater accuracy. When this option is specified, a standard 6' remote cable which attaches to the rear-mounted 9-Pin connector is provided. All function controls (TIMER, UP/DOWN, SET/STOP, SELECT/RESET and TIMER) are mounted on a 1/8" clear anodized aluminum switch plate. Extra cable length is available upon request. When this option "HR" (Hour or Hour & Half-Hour) is specified, a relay contact closure occurs on the Hour or on the Hour & Half-Hour (CLOCK time). The contacts are rated at 10 watts maximum resistive load, 500mA maximum switching current. The contact closure is accessible on the rear-mounted DB9 connector (see page 3). NOTE: Unless otherwise specified, Option "HR" includes a closure on the Hour & Half- Hour. A jumper on the PCB allows the Half-Hour feature to be defeated. When this option is specified, input voltage is 220 VAC, 50/60Hz. When this option is specified, the unit is housed in an Etched aluminum rackmount enclosure 1.75 high x 19 wide x 10 deep. When this option is specified, a 19 rackmount panel allows any two units with a P2 option to be mounted side by side. When this option is specified, the unit is housed in a console mount enclosure with an etched aluminum front panel 3.5 high x 9 wide x 8 deep. R - When this option is specified, all functions are accessible via a 9-Pin connector (see page 3). UL - W - ESE - When this option is specified, the unit is supplied with a UL approved wall mount power supply. When this option is specified, the unit is supplied with a three wire line cord. When this option (Serial Time Code output) is specified, the Time Code output is accessible via a rear BNC connector. The time code output is the same as what is currently being displayed.

3 CIRCUIT DESCRIPTION Page 3 The ES-562/564U is based on a single micro-processor chip, timer IC, Z4. A +5 volt DC supply consisting of T1, diodes D1-D3, capacitors C1-C6 and regulator Z2 power it. T1 provides 6 VAC to the voltage doubler circuit composed of D1-D2, C1-C4. Approximately +12 to +15 volts DC is developed across C1 and C3, which is regulated to 5 volts by Z2. This is used to power the clock/timer logic. A separate 6 VDC supply is used to supply the segment driver chip Z6. IC Z4 provides all timing and control functions and generates serial control signals for the display driver chips, Z6 and Z7. The display operates in multiplex mode. Z6 and Z7 receive segment and digit drive data from Z4 via a data line (Z4 pin 28), a clock line (Z4 pin 27) and a strobe line (Z4 pin 26). A 50 or 60 Hz clock signal is taken from T1, logic-level converted by Q1 and used for the counting timebase. Z4 also provides the optional Serial Timer Code, which is buffered by IC Z3. ES-562/564U Option "R" Connector Designations (DB9) Pin Function 1 Select/Reset 2 Set/Stop 3 Up 4 Down 5 Clock 6 Timer 7 Relay Contact (optional) 8 Relay Contact (optional) 9 Ground ES-562/564U Front View TIMER UP DOWN SET STOP SELECT RESET CLOCK

4 Page 4 ES-562/564U PARTS LIST PCB COMPONENTS QTY DESIGNATION DESCRIPTION PART NUMBER 1 Z2 INTEGRATED CIRCUIT LM330T Z4 INTEGRATED CIRCUIT P87C51SBPN-562U 1 Z6 INTEGRATED CIRCUIT UCN5895A 1 Z7 INTEGRATED CIRCUIT UCN5841A 1 X1 CRYSTAL MHZ 1 Q1 TRANSISTOR PN D1 - D3 DIODE 1N R22 - R28 RESISTOR 47 OHM 1/4 W 1 R29 RESISTOR 68 OHM 1/4 W 1 R6 RESISTOR 51K 1/4 W 1 R5 RESISTOR 120K 1/4 W 1 C10 CERAMIC CAPACITOR 10pf 50v Cer K 1 C11 CERAMIC CAPACITOR 25pf 50v Cer K 1 C8 CERAMIC CAPACITOR.01uf 50v Cer Z 2 C5, C7 CERAMIC CAPACITOR.1uf 50v Cer Z 1 C12 ELECTROLYTIC CAPACITOR 4.7uf 10v R El 1 C6 ELECTROLYTIC CAPACITOR 100uf 25v R El 4 C1 - C4 ELECTROLYTIC CAPACITOR 3300 UF 25V 1 SOCKET 16 PIN DIP SOCKET 1 SOCKET 18 PIN DIP SOCKET 1 SOCKET 40 PIN DIP SOCKET 3 N1 - N3 LED DISPLAY LTD6840Y 1 PCB UCT2 DISPLAY 1 PCB UCT-2 LOGIC CHASSIS COMPONENTS QTY DESIGNATION DESCRIPTION PART NUMBER 1 LINE CORD 2 WIRE LINE CORD 1 BUSHING 2 WIRE BUSHING 4 SWITCH #44 CREAM PB SWITCH 1 SWITCH 5212 C-OFF 1 T1 TRANSFORMER P CASE & HARDWARE ES-562/564U

5 ES-562/564U PARTS LIST Page 5 OPTIONAL COMPONENTS QTY DESIGNATION DESCRIPTION PART NUMBER 1 C9 (C) VARIABLE CAPACITOR 5-30 PF TRIMM 5MM V 1 Q2 (HR) TRANSISTOR 2N2907 or PN D4 (HR) DIODE 1N R7 (HR) RESISTOR 5.1K 1/4 W 1 K1 (HR) RELAY 1A5A RELAY 1 T1 (J) TRANSFORMER SSA6-6.3/230 2 T1, T2 (P) TRANSFORMER P T1, T2 (J AND P) TRANSFORMER P8705SSA5-6.3/230 6 R12, R17 - R21 (R) RESISTOR 1K 1/4 W 1 (HR AND R) CONNECTOR 9 PIN MALE D-SUB 1 (HR AND R) CONNECTOR 9 PIN FEMALE D-SUB 1 (HR AND R) CONNECTOR 9 PIN D-SUB HOOD 1 (S) CONNECTOR 25 Pin FEMALE D-sub 1 (S) CONNECTOR 25 Pin MALE D-sub 1 (S) CONNECTOR 25 Pin D-Sub Hood 1 R8 (SERIAL) RESISTOR 27 OHM 1/4W 1 Z3 (SERIAL) INTEGRATED CIRCUIT (SERIAL) SOCKET 16 PIN DIP SOCKET 1 (SERIAL) CONNECTOR BNC (UG-1094) 1 (UL) POWER PLUG UL PWR PLUG 1 T1 (UL) TRANSFORMER AA-061A5-206 "UL" 1 (W) LINE CORD 3 WIRE LINE CORD 1 (W) BUSHING 3 WIRE BUSHING

6 This page is not available with online manual requests and was intentionally left blank.

7 This page is not available with online manual requests and was intentionally left blank.

ES-362U PRESETTABLE MASTER TIMER

ES-362U PRESETTABLE MASTER TIMER 142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com ES-362U PRESETTABLE MASTER TIMER OPERATION AND MAINTENANCE MANUAL The ES-362U is a four digit, presettable 100 minute

More information

SRI-02 Speech Recognition Interface

SRI-02 Speech Recognition Interface SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.

More information

Sierra Radio Systems. Digital Compass. Reference Manual. Version 1.0

Sierra Radio Systems. Digital Compass. Reference Manual. Version 1.0 Sierra Radio Systems Digital Compass Reference Manual Version 1.0 Contents Digital compass board RS485 power injector For more information, go to the Sierra Radio Systems web site at www.sierraradio.net

More information

Sierra Radio Systems. HamStack. Project Board Reference Manual V1.0

Sierra Radio Systems. HamStack. Project Board Reference Manual V1.0 Sierra Radio Systems HamStack Project Board Reference Manual V1.0 Welcome HamStack Project Board Reference Manual Revision 1.0.3 2011 George Zafiropoulos, KJ6VU and John Best, KJ6K This guide provides

More information

A Programmer for the 68HC705C8 MicroController Figure 1 PROG05 As Built PROG05 User Guide Version C1 Page 1 of 14

A Programmer for the 68HC705C8 MicroController Figure 1 PROG05 As Built PROG05 User Guide Version C1 Page 1 of 14 A Programmer for the 68HC705C8 MicroController Figure 1 PROG05 As Built PROG05 User Guide Version C1 Page 1 of 14 Table of Contents midon design 1. Introduction...3 2. Description...4 3. Construction...5

More information

GLiPIC Ver C Assembly manual Ver 1.0

GLiPIC Ver C Assembly manual Ver 1.0 GLiPIC Ver C Assembly manual Ver 1.0 Last Rev 1.1 Oct 30, 2001 Author: Ranjit Diol Disclaimer and Terms of Agreement As with any kit, only the individual parts supplied are guaranteed against defects and

More information

K191 3 Channel RGB LED Controller

K191 3 Channel RGB LED Controller K191 3 Channel RGB LED Controller 1 Introduction. This kit has been designed to function as a versatile LED control module. The LED controller provides 3 high current channels to create light effects for

More information

Multi-Channel RS-232 Current Loop Interface Converter (CLIC)

Multi-Channel RS-232 Current Loop Interface Converter (CLIC) DECEMBER 1996 CL204A CL208A CL212A CL216A Multi-Channel RS-232 Current Loop Interface Converter (CLIC) CLIC 1/2A,SLO BLO,115VAC 1/4,SLO BLO,230VAC CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.:

More information

DEV-1 HamStack Development Board

DEV-1 HamStack Development Board Sierra Radio Systems DEV-1 HamStack Development Board Reference Manual Version 1.0 Contents Introduction Hardware Compiler overview Program structure Code examples Sample projects For more information,

More information

RKP08 Component List and Instructions

RKP08 Component List and Instructions RKP08 Component List and Instructions PCB layout Constructed PCB RKP08 Scematic RKP08 Project PCB Page 1 Description The RKP08 project PCB has been designed to use PIC microcontrollers such as the Genie

More information

CV Arpeggiator Rev 2 Build Documentation.

CV Arpeggiator Rev 2 Build Documentation. CV Arpeggiator Rev Build Documentation. Last updated 8-0-03 The CV Arpeggiator is a modular synth project used for creating arpeggios of control voltage. It utilizes a custom programmed PIC 6F685 micro

More information

Hardware User s Manual. Digital Video Motion Detector DVMD1-X

Hardware User s Manual. Digital Video Motion Detector DVMD1-X Hardware User s Manual Digital Video Motion Detector DVMD1-X Version 010 Revision A July, 2004 2395 Kenwood Drive Boulder, CO 80303 (303) 543-0440 TECHNICAL SPECIFICATIONS VENDOR Radiant Inc. http://www.dvmd.com

More information

DLA. DMX512 Analyzer. DLA Users Manual SV2_00 B.lwp copyright ELM Video Technology, Inc.

DLA. DMX512 Analyzer. DLA Users Manual SV2_00 B.lwp copyright ELM Video Technology, Inc. DLA DMX512 Analyzer DLA DLA-HH 1 Table Of Contents IMPORTANT SAFEGUARDS... 2 DLA OVERVIEW... 3 CONNECTION... 3 OPERATION... 3 HARDWARE SETUP... 4 DLA-HH (PORTABLE) LAYOUT... 4 CHASSIS LAYOUT... 4 DLA MENU

More information

Arrakis Systems 6604 Powell Street / Loveland, Colorado 80538

Arrakis Systems 6604 Powell Street / Loveland, Colorado 80538 Arrakis Systems 6604 Powell Street / Loveland, Colorado 80538 Input and Output wiring for the 150sc, 500sc, 2000sc and 2100sc audio consoles. A Input Channel Wiring (Back of Console) 6. Left Input 5. Left

More information

RLS-1000B Remote Link Switch

RLS-1000B Remote Link Switch RLS-000B Remote Link Switch Instruction Manual Computer Automation Technology Inc. 8 W. Atlantic Blvd. #9 Margate, Florida 06 Phone: 9 98-6 Internet: www.catauto.com The RLS-000B provides a method to connect

More information

Display Real Time Clock (RTC) On LCD. Version 1.2. Aug Cytron Technologies Sdn. Bhd.

Display Real Time Clock (RTC) On LCD. Version 1.2. Aug Cytron Technologies Sdn. Bhd. Display Real Time Clock (RTC) On LCD PR12 Version 1.2 Aug 2008 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended through suggestion

More information

solutions for teaching and learning

solutions for teaching and learning RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers

More information

N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B.

N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B. N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B. Background. This board is a copy of Andrew Lynch s Version 03 board (with 8 slots) but with added features. Added features: 9 SLOT Active Termination (copied

More information

DIY KIT 123. ATMEL 89xxxx PROGRAMMER

DIY KIT 123. ATMEL 89xxxx PROGRAMMER INTRODUCTION This kit is a powerful programmer for the Atmel 8051 family of microcontrollers. It supports the following devices: 89C1051, 89C2051 and 89C4051 89C51, 89LV51 89C52, 89LV52 89C55, 89LV55 89S8252,

More information

Schematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)

Schematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel) Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by

More information

KK1L 2x6 Antenna Switch Relay Controller / Dual Band Decoder Basic Assembly Version 4.8 (new 24-Aug-2009) Parts List updated 19-AUG-2016

KK1L 2x6 Antenna Switch Relay Controller / Dual Band Decoder Basic Assembly Version 4.8 (new 24-Aug-2009) Parts List updated 19-AUG-2016 KK1L 2x6 Antenna Switch Relay Controller / Dual Band Decoder Basic Assembly Version 4.8 (new 24-Aug-2009) Parts List updated 19-AUG-2016 Ronald Rossi, KK1L http://home.comcast.net/~kk1l Design Features:

More information

AEXX SERIES MULTI-FUNCTION CLOCK/TIMERS

AEXX SERIES MULTI-FUNCTION CLOCK/TIMERS FN:XXMFCT1.DOC AEXX SERIES MULTI-FUNCTION CLOCK/TIMERS AEXX SERIES MULTI-FUNCTION CLOCK/TIMERS REV 04/09/09 DESCRIPTION The AEXX Series of Multi-Function Clock/Timers are available with 1, 2.3, 4, 8, or

More information

Basic I/O Interface

Basic I/O Interface Basic I/O Interface - 8255 11 3 THE PROGRAMMABLE PERIPHERAL 82C55 programmable peripheral interface (PPI) is a popular, low-cost interface component found in many applications. The PPI has 24 pins for

More information

Bolt 18F2550 System Hardware Manual

Bolt 18F2550 System Hardware Manual 1 Bolt 18F2550 System Hardware Manual Index : 1. Overview 2. Technical specifications 3. Definition of pins in 18F2550 4. Block diagram 5. FLASH memory Bootloader programmer 6. Digital ports 6.1 Leds and

More information

4.0 Blue LED DCF77 Clock documentation

4.0 Blue LED DCF77 Clock documentation 4.0 Blue LED DCF77 Clock documentation 1. LED Clock Main Board PCB mounting: Mount and solder the eight wire bridges. Mount and solder resistors R16, R18, R20, R22. Mount and solder capacitors C1 C3 (pitch

More information

KDR00101 DMX Controlled Relay Kit

KDR00101 DMX Controlled Relay Kit KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or

More information

KDR00301 DMX Controlled Relay Kit

KDR00301 DMX Controlled Relay Kit KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or

More information

EL Wire sequencer / power supply PART NO

EL Wire sequencer / power supply PART NO EL Wire sequencer / power supply PART NO. 2206213 The EL Wire sequencer is a EL wire power supply capable of powering 50 plus feet of 2.6mm El Wire and 8 ports controlled by a BS2sx. A menu driven command

More information

Pacific Antenna Easy TR Switch Kit

Pacific Antenna Easy TR Switch Kit Pacific Antenna Easy TR Switch Kit Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate

More information

GL116 ENCODER/DECODER MANUAL GLOLAB CORPORATION

GL116 ENCODER/DECODER MANUAL GLOLAB CORPORATION GL ENCODER/DECODER MANUAL GLOLAB CORPORATION Thank you for buying our GL Encoder / Decoder Module. This device was developed in response to many requests for an encoder and decoder that would serialize

More information

KDS Channel DMX Controlled Servo Kit

KDS Channel DMX Controlled Servo Kit KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an

More information

Rapid28iXL PIC Prototyping PCB User Manual

Rapid28iXL PIC Prototyping PCB User Manual Description Features This is a PCB designed to facilitate the rapid prototyping of a device based on a 28 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of

More information

STATUS Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free

STATUS Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free Instruction Manual Model 1582-45L Data Switch September 2010, Rev A REMOTE LOCAL SWITCH STATUS SELECT REMOTE LOCAL LOCAL SELECT CHANNEL SELECT POWER MODEL 1582 SWITCH CROSS TECHNOLOGIES, INC. Data, drawings,

More information

IC-I AND IC-I F GENERAL DESCRIPTION SPECIFICATIONS. Output Impedance: Phones: 60 ohms (Unit is designed for use with ohm phones.

IC-I AND IC-I F GENERAL DESCRIPTION SPECIFICATIONS. Output Impedance: Phones: 60 ohms (Unit is designed for use with ohm phones. IC-I AND IC-I F GENERAL DESCRIPTION The IC-1 and IC-1 F are single-channel, singleline intercom stations designed for use with dynamic headsets. The IC-1 is a compact, lightweight unit which may be worn

More information

Rapid40iXL PIC Prototyping PCB User Manual

Rapid40iXL PIC Prototyping PCB User Manual Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping

More information

Manual Main PCB Small-MIDI 4

Manual Main PCB Small-MIDI 4 Index PARTLIST MAIN PCB... 2 INTRODUCTION... 3 GENERAL... 3 THE CIRCUIT... 3 ASSEMBLY KIT... 4 ASSEMBLY OF THE PCB... 4 An important tip...... 4 ASSEMBLY... 4 THE CONNECTORS... 4 Power supply J1... 4 IDC

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Board - Pro Module (E) Instruction Pointing the Way to Solutions! Controller I Version 2.1 The Board Pro E Module provides the following features: Up to 4 minutes recording time

More information

VG-305A AC Traffic Light Controller Kit

VG-305A AC Traffic Light Controller Kit Galak Electronics Electronic kits and components Website: GalakElectronics.com Email: sales@galakelectronics.com Phone: (302) 832-1978 VG-305A AC Traffic Light Controller Kit Thank you for your purchase

More information

Shack Clock kit. U3S Rev 2 PCB 1. Introduction

Shack Clock kit. U3S Rev 2 PCB 1. Introduction Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used

More information

M68HC705L4 PROGRAMMER BOARD APPLICATION NOTE

M68HC705L4 PROGRAMMER BOARD APPLICATION NOTE M68HC705L4PGMR JUNE 1992 M68HC705L4 PROGRAMMER BOARD (REVision A PWBs only) APPLICATION NOTE INTRODUCTION This application note describes the programming technique used to program and verify the XC68HC705L4

More information

Storage Card Interface Kit

Storage Card Interface Kit Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3K The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve

More information

Installation/assembly manual for DCC/Power shield

Installation/assembly manual for DCC/Power shield Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor

More information

Western Washington University. Electrical Engineering Technology. Etec 471. Professor Morton. Senior Hardware Description. Automated Aquarium

Western Washington University. Electrical Engineering Technology. Etec 471. Professor Morton. Senior Hardware Description. Automated Aquarium Western Washington University Electrical Engineering Technology Etec 471 Professor Morton Senior Hardware Description Automated Aquarium Greg Rose 4/27/04 Introduction The Automated Aquarium Controller

More information

Transcendent Frequency Counter

Transcendent Frequency Counter Transcendent Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and operate this frequency counter KIT. Features: The transcendent counter has two input channels

More information

E3B USER'S GUIDE. for QT310 / QT320 QProx IC evaluation and development Overview. Fast Start

E3B USER'S GUIDE. for QT310 / QT320 QProx IC evaluation and development Overview. Fast Start E3B USER'S GUIDE for QT310 / QT320 QProx IC evaluation and development Overview The E3B board works with Quantum s QT310 and QT320 QProx ICs. Either device can be inserted into the 8-pin DIP socket. QT310

More information

PH Probe for the PIC Temperature Controller

PH Probe for the PIC Temperature Controller PH Probe for the PIC Temperature Controller This is a ph probe amplifier designed to match any standard PIC micro analogue input port, as originally used on a PIC 16F and 18F Aquarium Temperature Controller

More information

um-fpu64 Floating Point Coprocessor 28-pin Breakout Board Introduction Bare um-fpu64 28-pin Breakout Board

um-fpu64 Floating Point Coprocessor 28-pin Breakout Board Introduction Bare um-fpu64 28-pin Breakout Board Floating Point Coprocessor Breakout Board Introduction The breakout board has all of the required connections, and provides access to all um- FPU64 pins. It can be used as a development board or for permanently

More information

Sprinkler Controller Assembly Manual

Sprinkler Controller Assembly Manual Sprinkler Controller Assembly Manual V1.0 Doug Jackson VK1ZDJ September 2010 Licence The Sprinkler Controller Design, PCB layout, Manual, and Firmware is Copyright 2010, by Douglas Jackson, VK1ZDJ. This

More information

V1BOOST-STEPPER Unipolar Stepper Motor BoosterPack for the MSP430 LaunchPad. User s Guide

V1BOOST-STEPPER Unipolar Stepper Motor BoosterPack for the MSP430 LaunchPad. User s Guide V1BOOST-STEPPER Unipolar Stepper Motor BoosterPack for the MSP430 LaunchPad User s Guide Revised July 2012 CONTENTS 1 Introduction... 3 1.1 Overview... 3 1.2 Features... 3 1.3 Additional Information...

More information

QUASAR PROJECT KIT # ATMEL AVR PROGRAMMER

QUASAR PROJECT KIT # ATMEL AVR PROGRAMMER This kit is a simple but powerful programmer for the Atmel AT90Sxxxx ( AVR ) family of microcontrollers. The Atmel AVR devices are a low-power CMOS 8-bit microcontroller using a RISC architecture. By executing

More information

Home Security System with Remote Home Automation Control

Home Security System with Remote Home Automation Control Home Security System with Remote Home Automation Control Justin Klumpp Senior Project Hardware Description Western Washington University April 24 2005 Professor Todd Morton Introduction: This document

More information

USB board Mk2 INSTRUCTION MANUAL

USB board Mk2 INSTRUCTION MANUAL USB board Mk2 INSTRUCTION MANUAL Revision 0, December 2017 This manual comprises introducing information on use and performance of this device. For more information please refer to the Audial web site,

More information

The PUMPKIN LIGHT LED

The PUMPKIN LIGHT LED The PUMPKIN LIGHT LED PUMPKIN LIGHT LED By Mark McCuller Email: mcculler@mail.com DESIGN SUMMARY The PUMPKIN LIGHT LED By: Mark McCuller The Pumpkin Light LED is a battery-powered device that illuminates

More information

Stellar Instruments. SC1 Controller & Display System. General User s Manual. Copyright 2013 Stellar Instruments 1

Stellar Instruments. SC1 Controller & Display System. General User s Manual. Copyright 2013 Stellar Instruments 1 Stellar Instruments SC1 Controller & Display System General User s Manual Copyright 2013 Stellar Instruments 1 Contents Section 1 General... 3 Section 2 Base Unit A (Multi-Event Programmable Timer)...

More information

QRPGuys Digital Dial/Frequency Counter

QRPGuys Digital Dial/Frequency Counter QRPGuys Digital Dial/Frequency Counter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com

More information

C S Technology Ltd. cstech.co.uk. DTMF display 32 kit with 2 line x 16 LCD display

C S Technology Ltd. cstech.co.uk. DTMF display 32 kit with 2 line x 16 LCD display C S Technology Ltd cstech.co.uk DTMF display 32 kit with 2 line x 16 LCD display Our DTMF display can display up to 32 characters (16 per line). The display can be cleared by a button (not supplied) or

More information

KUANTECH (SHEN ZHEN) COMPANY LIMITED KSAFD W1UK

KUANTECH (SHEN ZHEN) COMPANY LIMITED KSAFD W1UK 1 GENERAL... 2 1.1 Description... 2 2 INPUT REQUIREMENTS... 2 2.1 Input Conditions... 2 2.2 AC Inrush Current... 2 3 OUTPUT REQUIREMENTS... 2 4 MECHANICAL... 3 4.1 Enclosure And Layout... 3 4.2 Input and

More information

Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article

Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article Images Company Robotic Arm PC Interface allows real time computer control and an interactive script writer/player for programming and

More information

Instruction Manual for BE-SP3 Circuit. 10/21/07

Instruction Manual for BE-SP3 Circuit. 10/21/07 Page 1 of 54 Instruction Manual for BE-SP3 Circuit. 10/21/07 Page 1 Index: Page 2 BE-SP3 Circuit Specifications. Page 3-4 Intro to the BE-SP3. Page 5 Basics of serial to parallel. Page 6-7 ASCII Code.

More information

Shack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3

Shack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3 1. Introduction Shack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3 Thank you for purchasing this QRP Labs Shack Clock kit. The kit uses the same PCB and bag of components as some other QRP Labs kits.

More information

KPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P

KPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P Devices Included in this Data sheet: KPIC-0818P Features: Carefully designed prototyping area Accepts 8 pin PIC12 series micro-controllers Accepts 14 and 18 Pin PIC16 series Accepts some 8,14 and 18 pin

More information

Zippy AVR Programmer. Zippy Programmer Features. Lomae Pty Ltd PO BOX 1297 Baulkham Hills, NSW,1755 ACN

Zippy AVR Programmer. Zippy Programmer Features. Lomae Pty Ltd PO BOX 1297 Baulkham Hills, NSW,1755 ACN PO BOX 97 ACN 0 80 56 Zippy AVR Programmer Introduction When Atmel released their 8 Bit AVR Microcontroller range, they also released a complete development system that allowed engineers to start developing

More information

Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.

Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit

More information

Installation & Operation Guide

Installation & Operation Guide Installation & Operation Guide (Shown with optional Override Board Cover) KMD-5831 Programmable Loop Controller PLC-28 Direct Digital Controller 902-019-04B 1 Introduction This section provides a brief

More information

solutions for teaching and learning

solutions for teaching and learning RKOneAnalogue Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKOneAnalogue Software Development PCB Page 1 Description The RKOneAnalogue software development PCB has been

More information

ARRL ETP Solder Hour Clock Kit Construction Manual

ARRL ETP Solder Hour Clock Kit Construction Manual ARRL ETP Solder 101 24-Hour Clock Kit Construction Manual Do a complete parts check cross checking the individual parts against the parts list. Pay particular attention to the color code for the resistors:

More information

Figure 1 FS710 Front Panel

Figure 1 FS710 Front Panel INTRODUCTION The Model FS710 10 MHz AGC Distribution Amplifier provides seven sine wave outputs from a single 10 MHz source. Designed as an accessory to the FS700 LORAN Receiver, the FS710 AGC circuitry

More information

Temperature Measurement

Temperature Measurement Copyright 1999-2002. All rights reserved. Web design by Sullivan Creative -1000 to +3500 and -10000 to +35000 Count Thermocouple, RTD, and Thermistor Temperature Measurement in C or F without Recalibration

More information

css Custom Silicon Solutions, Inc.

css Custom Silicon Solutions, Inc. css Custom Silicon Solutions, Inc. CSS555 EZ Programmer Operating Manual Version 1.0, May 2012 Contents Operating Instructions & Features.... 2 Programmer PCB Diagram.... 3 555 Timer Configuration Settings

More information

BASIC Stamp Activity Board: Features and Specifications

BASIC Stamp Activity Board: Features and Specifications 27905 w / Power Supply 27906 w/o Power Supply BASIC Stamp Activity Board: Features and Specifications The BASIC Stamp Activity Board (BSAC) is a demonstration board for Parallax BASIC Stamp computers (BS1-IC,

More information

Keywords Digital IC tester, Microcontroller AT89S52

Keywords Digital IC tester, Microcontroller AT89S52 Volume 6, Issue 1, January 2016 ISSN: 2277 128X International Journal of Advanced Research in Computer Science and Software Engineering Research Paper Available online at: www.ijarcsse.com Digital Integrated

More information

Electronic Lock CodeLock AVR 1 DIY electronic door lock

Electronic Lock CodeLock AVR 1 DIY electronic door lock Electronic Lock CodeLock AVR 1 DIY electronic door lock CodeLock AVR LCD CodeLock AVR electronic lock is realised with Atmel AVR micro-controller AT90S2313, ATtiny2313 or ATtiny45. 1 user code in the program

More information

AP21LV SERIES TIME SWITCHES version 2 TABLE OF CONTENTS

AP21LV SERIES TIME SWITCHES version 2 TABLE OF CONTENTS AP21LV SERIES TIME SWITCHES version 2 TABLE OF CONTENTS INTRODUCTION.......................... Page 2 SPECIFICATIONS.......................... Page 3 INSTALLATION.......................... Page 4 DESCRIPTION..........................

More information

Rapid40i PIC Prototyping PCB User Manual

Rapid40i PIC Prototyping PCB User Manual Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping

More information

GSV-1A4 M12/2 M12/2. Highlights

GSV-1A4 M12/2 M12/2. Highlights GSV-1A4 M12/2 M12/2 Highlights Input sensitivity: 2mV/V; 4mV/V, 2 mv/v, 1mV/V, 0.5mV/V configurable via jumpers Output signals ±10V AND 12mA+-8mA on 15 pin Sub-D Integrated half and quarter bridge completion

More information

MANUAL FOR THE UNIVERSAL MANUAL CONTROLLER UMC - 31

MANUAL FOR THE UNIVERSAL MANUAL CONTROLLER UMC - 31 MANUAL FOR THE UNIVERSAL MANUAL CONTROLLER UMC - 31 PPS PART NO. 133550 DRAWING NO. 133550-10 THIS MANUAL ASSIGNED TO THE S/N: THE INFORMATION CONTAINED IN THIS MANUAL IS PROPRIETARY TO PACIFIC POWER SOURCE,

More information

PSM-2 POWER SUPPLY MODULE INSTRUCTIONS

PSM-2 POWER SUPPLY MODULE INSTRUCTIONS PSM2-09.doc 1 Rev: 8-28-01 PSM-2 POWER SUPPLY MODULE INSTRUCTIONS PSM Model 2 equipped with Field Programmable Output Voltages MODEL PRODUCT OFFERING / VARIATIONS: PSM-2 Metal case housed surface mountable

More information

DMX CONTROLLED RELAY K8072

DMX CONTROLLED RELAY K8072 Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 f the means o ol. y b y la a re 2 protoc Control DMX51 wn well-kno ILLUSTRATED ASSEMBLY MANUAL Total solder

More information

AEXX-273 SERIES WIRELESS CONTROLLED PACE CLOCKS

AEXX-273 SERIES WIRELESS CONTROLLED PACE CLOCKS FN:273MAN1.DOC AEXX-273 SERIES WIRELESS CONTROLLED PACE CLOCKS DESCRIPTION AEXX-273 Series Wireless Controlled Pace Clocks are available in with 1", 2.3", 4", 8", or 12" high digits, visible from 5 feet

More information

Strain Gage Measuring Amplifier GSV-1

Strain Gage Measuring Amplifier GSV-1 Strain Gage Measuring Amplifier GSV-1 Tel 03302 559 282, Fax: 03302 559 141, info@me-systeme.de, www.me-systeme.de 1 Strain Gage Measuring Amplifier GSV-1 Description...3 Models...4 Technical Data...5

More information

Sierra Radio Systems. Making a Keyer with the. HamStack. Project Platform

Sierra Radio Systems. Making a Keyer with the. HamStack. Project Platform Sierra Radio Systems Making a Keyer with the HamStack Project Platform Introduction The HamStack Project Board includes primary interface elements needed to make a high quality CW keyer. Using the LCD

More information

DIY KIT 121. ATMEL 89Cx051 PROGRAMMER

DIY KIT 121. ATMEL 89Cx051 PROGRAMMER Microcontrollers (uc s) have been around for quite a while now. With relatively few I/O lines, a limited instruction set and almost no peripherals they are far better suited for control applications than

More information

Building the RGBW LED Controller

Building the RGBW LED Controller Building the RGBW LED Controller A guide for the assembly and operation of your RGBW LED Controller. ver 3.1 Getting Started Parts list - You should have received the following parts: (1) Circuit Board,

More information

Digital Keypad Introduction

Digital Keypad  Introduction K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming

More information

icex-cmtm General specs and Installation guide

icex-cmtm General specs and Installation guide icex-cmtm General specs and Installation guide 1. General view 2. Specifications 2.1. Common specs: Ethernet 1 x 10/100Base/T, RJ45 connector with traffic and link LED Serial Interface 1 x RS232/485 USB

More information

ISO 9001 CERTIFIED. 607 NW 27th Ave Ocala, FL Phone: (352) or Fax: (352) OPERATION MANUAL

ISO 9001 CERTIFIED. 607 NW 27th Ave Ocala, FL Phone: (352) or Fax: (352) OPERATION MANUAL ISO 9001 CERTIFIED Phone: (352) 629-5020 or 800-533-3569 Fax: (352)-629-2902 ES-Key 16 Output module (selectable polarity) P/N 610-00031 PAGE 1 of 10 1. REVISION LOG... 1 2. MODULE OVERVIEW... 2 2.1. SCOPE...

More information

RC-210 Repeater Controller Assembly Manual

RC-210 Repeater Controller Assembly Manual Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net RC-210 Repeater Controller Assembly Manual Hardware Version 3.0 Original Release Date September 13, 2004

More information

Single Phase Systems-North American PC125/PC420 Series

Single Phase Systems-North American PC125/PC420 Series Single Phase Systems-North American PC125/PC420 Series Enclosure Power Distribution Units (epdu ) PC125-C Front RACK MOUNTED 19 x 3.4 (2U) x 8.5. Approximate shipping weight: 19 lbs. (12) NEMA OUTLETS

More information

RC210 Repeater Controller Assembly Manual

RC210 Repeater Controller Assembly Manual Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net http://www.arcomcontrollers.com/ RC210 Repeater Controller Assembly Manual Hardware Version 3.3 Reproduction

More information

Universal Keying Adapter 3+

Universal Keying Adapter 3+ Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port

More information

Variable Power Supply Digital Control Circuit Diagram Using Lm317

Variable Power Supply Digital Control Circuit Diagram Using Lm317 Variable Power Supply Digital Control Circuit Diagram Using Lm317 DIGITAL POWER SUPPLY USING LM317 A Major Project Report Submitted partial fulfillment of the requirement for the award of the Degree of

More information

Secrure door control and I/O expansion. Installation Guide. (ver 1.0)

Secrure door control and I/O expansion. Installation Guide. (ver 1.0) Secrure door control and I/O expansion Installation Guide (ver 1.0) www.supremainc.com Contents Product Contents 3 Front Panel Description 4 Rear Panel Description 5 Connectors for External Interfaces

More information

SmartFan Fusion-4. Speed Control and Alarm for DC Fans CONTROL RESOURCES INCORPORATED. The driving force of motor control & electronics cooling.

SmartFan Fusion-4. Speed Control and Alarm for DC Fans CONTROL RESOURCES INCORPORATED. The driving force of motor control & electronics cooling. SmartFan Fusion-4 Speed Control and Alarm for DC Fans The driving force of motor control & electronics cooling. P/N FUS300-F DC Controls SmartFan Fusion-4 is a digital fan speed control and alarm that

More information

GENERAL DESCRIPTION SPECIFICATIONS. output Impedance: Phones: 60 ohms (Designed for use with ohm phones.)

GENERAL DESCRIPTION SPECIFICATIONS. output Impedance: Phones: 60 ohms (Designed for use with ohm phones.) GENERAL DESCRIPTION The IC-S is a single-channel speaker station designed for use with an external microphone. There are four versions of the IC-S; all identified by the same model name, but distinguished

More information

Exclusive 2.5 GHz Frequency Counter

Exclusive 2.5 GHz Frequency Counter Exclusive 2.5 GHz Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and tune this frequency counter KIT. Features: Frequency range from 5 MHz to 2.5GHz Factory

More information

Educato. Assembly Instructions

Educato. Assembly Instructions Product Description The Educato is an Arduino compatible board that has about the functionality of the Arduino Uno. It also has the ability, however, to plug into a solderless breadboard and to have all

More information

WOODINVILLE, WA SUPERSTEP 2100 SERIES SEQUENCING PROPORTIONAL LOAD CONTROLLERS INSTALLATION & OPERATING MANUAL. Models: SLC2102-SLC2112

WOODINVILLE, WA SUPERSTEP 2100 SERIES SEQUENCING PROPORTIONAL LOAD CONTROLLERS INSTALLATION & OPERATING MANUAL. Models: SLC2102-SLC2112 SELECTRONIX, INC. WOODINVILLE, WA SUPERSTEP 2100 SERIES SEQUENCING PROPORTIONAL LOAD CONTROLLERS INSTALLATION & OPERATING MANUAL Models: SLC2102-SLC2112 SLC2102X-SLC2112X SLC2152-SLC2162 SLC2170-xx Relay

More information

Cumbria Designs T-1. C-1 Controller. User Manual

Cumbria Designs T-1. C-1 Controller. User Manual Cumbria Designs T-1 C-1 Controller User Manual CONTENTS 1 INTRODUCTION 2 2 CIRCUIT DESCRIPTION 2 3 ASSEMBLY 3 4 CONNECTIONS AND CONFIGURATION 4 5 TESTING 6 Appendix A C-1 Circuit Diagram and PCB Component

More information

HD DIGITAL VIDEO A/B SWITCH INSTALLATION MANUAL

HD DIGITAL VIDEO A/B SWITCH INSTALLATION MANUAL DVS772HD HD DIGITAL VIDEO A/B SWITCH INSTALLATION MANUAL IB6445-01 DESCRIPTION The DVS772HD high definition DIGITAL VIDEO SWITCH is a high isolation high frequency relay used to switch digital signals

More information

BG1B Universal Gate Drive Prototype Board

BG1B Universal Gate Drive Prototype Board BG1B Universal Gate Drive Prototype Board Description: The BG1B is a single channel gate drive circuit board for high power IGBT modules. The BG1B utilizes Powerex hybrid gate drivers and DC-to-DC converters

More information