Main Menu. Menu II. UNPACKING AND SETUP II-5. RADF MR-3021/3022

Size: px

Start display at page:

Download "Main Menu. Menu II. UNPACKING AND SETUP II-5. RADF MR-3021/3022"

Calvin Fitzgerald
5 years ago
Views:

PRECAUTIONS UNPACKING ACCESSORIES SETUP CLEARANCE ADJUSTMENT OPERATION CHECK SKEW ADJUSTMENT LEADING EDGE POSITION ADJUSTMENT HORIZONTAL POSITION ADJUSTMENT COPY RATIO ADJUSTMENT There is no

1 PRECAUTIONS UNPACKING ACCESSORIES SETUP CLEARANCE ADJUSTMENT OPERATION CHECK SKEW ADJUSTMENT LEADING EDGE POSITION ADJUSTMENT HORIZONTAL POSITION ADJUSTMENT COPY RATIO ADJUSTMENT There is no difference in the unpacking and set-up procedures between MR-3021 and MR Therefore, this chapter takes MR-3022 for the purpose of illustration. Menu Main Menu TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 1

- Turn the power OFF with the main power switch. Be sure to install the equipment near an electric outlet so that it is easily accessible.

2 OFF Be sure to shut down the equipment and unplug the power cable before any option is installed. The procedure for the shutdown is as follows: - Press the [ON/OFF] button until you hear a sound. - Confirm that the ON/OFF lamp is out. - Turn the power OFF with the main power switch. Be sure to install the equipment near an electric outlet so that it is easily accessible. * For Japan, remove the ground wire after the power cable is unplugged. When the option is installed, be sure to install the ground wire first and then plug in the power cable. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 2

Take out the RADF from the packing carton.

3 UNPACKING Open the packing carton. Take out the unpacking instructions and the test chart. Take out the accessories. Remove the packing materials. Take out the RADF from the packing carton. Remove the plastic bag. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 3

4 UNPACKING Peel off the 2 pieces of adhesive tape. Peel off the adhesive tape and remove the packing material. Take out the accessories. *The packing material on the platen sheet side is removed after the RADF is temporarily installed in the e-studio. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 4

5 ACCESSORIES 2 SHOULDER COIN SCREWS 2 COIN SCREWS 2 SHOULDER SCREWS & WASHER 2 POSITIONING PINS 2 TEST CHARTS HINGE STOPPER 2 HINGE STOPPER FIXING SCREWS TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 5

SETUP Unscrew the screw fixing the damper.

SETUP Unscrew the 2 screws of the rear top cover.

SETUP Adjust the installation position of the

10 SETUP Adjust the installation position of the RADF so that the 2 coin screws make contact with the marking on the hinge. Temporarily tighten the coin screws. *Make sure of the following points. Paper feed side: The coin screw contacts the marking at a single point. Paper exit side: The coin screw contacts the concave marking at three points. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 10

11 SETUP Remove the packing material. Close the RADF. Temporarily tighten the shoulder screw along with the washer at the paper exit side on the rear of the RADF. Open the RADF. Remove the 2 rubber caps, then insert the 2 positioning pins into the screw holes. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 11

13 SETUP Gently close the RADF halfway down. Make sure that the 2 positioning pins are smoothly inserted into the slots of the RADF while it is fully closed under its own weight. If the pins cannot be smoothly inserted, adjust the installation position of the RADF. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 13

14 SETUP After the adjustment, fully tighten the shoulder screw at the paper exit side on the rear. Loosen the 2 screws fixing the hinge at the paper feed side on the rear of the RADF so that the screw hole comes to the center of the bracket slot. Tighten the shoulder screw. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 14

Gently close the RADF, and then hold it down from above

17 SETUP Open the RADF. Place the removed platen sheet on the original glass so that it is aligned with the rear and left original scales. Gently close the RADF, and then hold it down from above to let the platen sheet adhere to it. Close the RADF. Secure the hinge stopper with the screw. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 17

Make sure that the platen sheet is fully adhering to it.

18 SETUP Tighten the removed positioning pins into the hinge bracket at the paper feed side. Reuse them when the position of the RADF needs to be readjusted. Open the RADF. Make sure that the platen sheet is fully adhering to it. Remove the connector cover from the rear of the e-stduio. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 18

Connect the interface cable from the RADF.

20 CLEARANCE ADJUSTMENT This is the adjustment of the clearance between the protrusion of the RADF and the top surface of the original glass. Turn the power ON with the main power switch while pressing [0] and [3] simultaneously. Key in [267], and then press the [START] button. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 20

CLEARANCE ADJUSTMENT Check the clearance while the exposure lamp

21 CLEARANCE ADJUSTMENT Check the clearance while the exposure lamp is lit. Make sure of the following points: - The white protrusion of the front of the RADF makes contact with the top surface of the original glass. - There is 0 to 0.5 mm clearance between the black protrusion of the rear of the RADF and the top surface of the original glass. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 21

Turning the adjustment screw clockwise widens the clearance.

22 CLEARANCE ADJUSTMENT If a clearance adjustment is needed at the rear, turn the adjustment screw of the hinge at the paper exit side at the rear. Turning the adjustment screw clockwise widens the clearance. On the other hand, turning it counterclockwise narrows the clearance. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 22

23 CLEARANCE ADJUSTMENT If a clearance adjustment is needed at the front, turn the adjustment screw of the hinge at the paper feed side at the rear. Turning the adjustment screw clockwise widens the clearance. On the other hand, turning it counterclockwise narrows the clearance. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 23

OFF ON Place the co-packed test chart on the original feed tray of the

24 OPERATION CHECK Turn the power OFF with the main power switch and then back ON. OFF ON Place the co-packed test chart on the original feed tray of the RADF with the page to be copied facing down. Press the [START] button to make a simplex copy. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 24

25 OPERATION CHECK Make sure that there is no problem with the copied image regarding the following 4 points: - The copied image is not skewed. (Skew adjustment) - Appropriate margins are provided on the copied image. (Leading edge position adjustment) - The line drawn in the copy direction is located at the center of the copied image. (Horizontal position adjustment) - The copied image is not enlarged or reduced. (Copy ratio adjustment) TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 25

26 OPERATION CHECK In addition, place the test chart on the original feed tray of the RADF with the page to be copied facing down to check the leading edge of the original in duplex copying. Make a duplex copy. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 26

SKEW ADJUSTMENT Perform the following steps for the skew adjustment: *Prior to this adjustment, make sure that the copied image is not skewed when an original is manually placed on the original glass

27 SKEW ADJUSTMENT Perform the following steps for the skew adjustment: *Prior to this adjustment, make sure that the copied image is not skewed when an original is manually placed on the original glass ** Make sure that the RADF installation adjustment and the height adjustment have been properly performed. If the copied image is skewed as shown in simplex copying, open the jam access cover. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 27

28 SKEW ADJUSTMENT Unscrew the screw fixing the plate at the front of the jam access cover, and then temporarily tighten it into the oblong hole. Loosen the lower screw. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 28

31 SKEW ADJUSTMENT Perform the following steps for the skew adjustment in the duplex copying. If the copied image is skewed as shown, open the jam access cover and the reverse guide. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 31

SKEW ADJUSTMENT Unscrew the screw fixing the plate at the front of the reverse guide, and then

SKEW ADJUSTMENT If the copied image is skewed as shown, slide the

35 LEADING EDGE POSITION ADJUSTMENT Perform the following steps for leading edge position adjustment. Shut down the e-studio if leading edge position adjustment is required in a simplex copy. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 35

36 LEADING EDGE POSITION ADJUSTMENT Start up the e-studio in the [05] ADJUSTMENT mode. Key in [365], and then press the [START] button. To reduce the margin of the leading edge of the copied image, key in a value smaller than the current one, and then press [ENTER]. SMALLER VALUE THAN THE CURRENT ONE ENTER * Decreasing the value shifts the image by approx. 0.1 mm per 1 step. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 36

37 LEADING EDGE POSITION ADJUSTMENT To increase the margin, key in a value larger than the current one, and then press [ENTER]. LARGER VALUE THAN THE CURRENT ONE ENTER * Increasing the value shifts the image by approx. 0.1 mm per 1 step. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 37

38 LEADING EDGE POSITION ADJUSTMENT If leading edge position adjustment is required in duplex copying, key in [366] in the [05] ADJUSTMENT mode, and then press the [START] button. To reduce the margin of the leading edge of the copied image, key in a value smaller than the current one, and then press [ENTER]. SMALLER VALUE THAN THE CURRENT ONE ENTER * Decreasing the value shifts the image by approx. 0.1 mm per 1 step. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 38

39 LEADING EDGE POSITION ADJUSTMENT To increase the margin, key in a value larger than the current one, and then press [ENTER]. LARGER VALUE THAN THE CURRENT ONE ENTER * Increasing the value shifts the image by approx. 0.1 mm per 1 step. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 39

40 HORIZONTAL POSITION ADJUSTMENT Perform the following steps for the horizontal position adjustment. Key in [358] in the [05] ADJUSTMENT mode, and then press the [START] button. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 40

41 HORIZONTAL POSITION ADJUSTMENT If the copied image deviates to the front, key in a value larger than the current one, and then press [ENTER]. LARGER VALUE THAN THE CURRENT ONE ENTER * Increasing the value shifts the image by approx mm per 1 step. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 41

42 HORIZONTAL POSITION ADJUSTMENT If the copied image deviates to the rear, key in a value smaller than the current one, and then press [ENTER]. SMALLER VALUE THAN THE CURRENT ONE ENTER * Decreasing the value shifts the image by approx mm per 1 step. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 42

43 COPY RATIO ADJUSTMENT Compare the copied image with the test chart. If the image is enlarged or reduced, perform the following steps for the copy ratio adjustment. Key in [357] in the [05] ADJUSTMENT mode, and then press the [START] button. TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 43

44 COPY RATIO ADJUSTMENT If the copied image is larger than the test chart, key in a value smaller than the current one, and then press [ENTER]. SMALLER VALUE THAN THE CURRENT ONE ENTER TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 44

45 COPY RATIO ADJUSTMENT If the copied image is smaller than the test chart, key in a value larger than the current one, and then press [ENTER]. LARGER VALUE THAN THE CURRENT ONE ENTER TOSHIBA TEC CORPORATION 2011 All Rights Reserved. 45

PoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.

ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power