lighting, electrics & communications

Transcription

1 lighting, electrics & communications P RO D U C T M A P L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S O V E RV I E W L I G H T I N G B A S I C S C E I L I N G F E E D B A S I C S B A S E F E E D B A S I C S P OW E R D I S T R I B U T I O N B A S I C S P OW E R A C C E S S B A S I C S C O M M U N I C AT I O N S A C C E S S B A S I C S C A S U A L W I R E B A S I C S P RO D U C T L I S T I N G

2 product map T U Universal Light T Y R C Slim Profile Utility Light B F K Base Feed Page 302 Page 303 Page 304 B F K S Split Base Feed B F K P Plug-In Base Feed E P T Power Pole (Complete) Page 305 Page 306 Page 307 E P T E Page 308 Power Pole (No Harness) E P D Page 309 Pole Divider E P H T Page 310 High Capacity Power Pole (Complete) E P H T E Page 311 High Capacity Power Pole (No Harness) E P B Page 312 Power Pole Harness (Includes Junction Box) E S Page 313 Receptacle Harness

3 product map E T Quadrex Receptacle Harness E H Panel Pass-Through Harness E I No Raceway Jumper Page 314 Page 315 Page 316 E F Four-Way Connector E G Off-Module Jumper T M C M-Clip Page 317 Page 318 Page 319 E D Outlets E D 8 N Outlets (Separate Neutral) E D 8 K Outlets (Dual Isolated) Page 320 Page 321 Page 322 Duplex Triplex Duplex Triplex Duplex Triplex E D S 5 Page 323 Surge Suppressor E D C Page 324 Outlet Knockout Cover E R B Page 325 Raceway Box Single Double

4 product map E R B 8 N Raceway Box (Separate Neutral) E R B 8 K Raceway Box (Dual Isolated) V D M Voice & Data Module Page 326 Page 327 Page Single Double Single Double 2200 V D A Page 329 Voice & Data Adapter E V D F Page 330 Voice & Data Faceplate Adapter D M P Page 331 Access Door VDM Plates C C H Chicago Corner Ducts E P C Retractable Power Center T Z W Worksurface Tray Page 332 Page 333 Page 334 Widths: 15" - 87" G S T Z P Panel Tray Page 335 Widths: 18" - 60" T Z B Bridge Tray Page 336 Widths: 72" - 96"

5 product map lyft H B C C Page 337 Base Cable Clips

6 lighting, electrics & communications overview Transit offers a variety of lighting, electrical and communications components to accommodate all electrical needs. Transit has six different wire systems to accommodate a broad range of power requirements The electrical contractor is responsible for power distribution in order to obtain a balanced system within the limits of the building Local codes must be checked to ensure compliance Power Pole (Complete) (EPT) Power Pole (No Harness) (EPTE), Pole Divider (EPD), High Capacity Power Pole (Complete) (EPHT) or High Capacity Power Pole (No Harness) (EPHTE) also available Retractable Power Center (EPC) Off-Module Jumper (EG) Power Pole Harness (EPB) Voice & Data Module (VDM) Voice & Data Faceplate Adapter (EVDF) Voice & Data Adapter (VDM) Access door (VDM) Plate (DMP) Slim Profile Utility Light (TYRC) Four-Way Connector (EF) Universal Light (TU) Raceway Box (ERB) Separate Neutral (ERB8N) and Dual Isolated (ERB8K) also available Outlets (ED) Separate Neutral (ED8N), Dual Isolated ( ED8K), Surge Suppressor (EDS5) and Outlet Knockout Cover (EDC) also available Base Feed (BFKP) Split Base Feed (BFKS) and Plug-In Base Feed (BFKP) also available Quadrex Receptacle Harness (ET) Receptacle Harness (ES) Panel Pass Through-Harness (EH) Also available but not illustrated above: Chicago Corner Ducts (CH) M-Clip (TMC) Worksurface Tray (TZW), Panel Tray (TZP) or Bridge Tray (TZB) No Raceway Jumper (EI) CH45 CH90 CH180 CH4 CHG CHS TZW TZP TZB

7 lighting basics The following lighting options are available in Transit. Universal Light (TU) Magnetically mounts anywhere along the underside of the Overhead Cabinet (TSF) or Shelf (TSS) Is equipped with an energy-efficient warm fluorescent tube and an asymmetrical reflector that aids in the elimination of veiling reflection Complete with a 108" long cord which can be concealed in the vertical upright of the panel, and is managed with a wire management clip that routes it to power at the access level Also Available: Conflux Undercabinet (YLCU) Please see Complements: Teknion s Ergonomics & Accessories Program Finishes All lighting products are available in Foundation and Mica colors Slim Profile Utility Light (TYRC) Mounts to the underside of the Overhead Cabinet (TSF) to provide moveable side-to side task lighting for the worksurface Is equipped with an energy-efficient, cool white florescent tube and a multi-faceted plastic lens which spreads light uniformly over the worksurface Electronic ballasts (normal power factor) are cooler, quieter and more energy efficient than standard ballasts When applying this light to an overhead cabinet, specify the width one size smaller than the width of the cabinet Complete with a 108" long cord which can be concealed in the vertical upright of the panel, and is managed with a wire management clip that routes it to power at the access level

8 ceiling feed basics Transit offers several options for bringing the power to a workstation from the ceiling. They are outlined below. The top trim style of the panel on which a power pole is mounted must be specified so that appropriate top trim plates can be supplied Electrical harnesses and communication cables should not be used together within a pole without a pole divider The electrical contractor is responsible for power distribution in order to obtain a balanced system within the electrical limits of the building Optional Pole Divider 111" Harness Power Pole (Complete) (EPT) Routes power or communications directly from the building supply in the ceiling to he raceway level of the panel, and includes an electrical harness and a junction box Poles are provided with a 111" harness Power Pole (No Harness) (EPTE) Does not include electrical harnesses or a junction box, but provides a safe enclosure in which to route power and communications from the ceiling to the top of the panel Pole Divider (EPD) Enables the separation of electrical harnesses and communication cables within a power pole This divider is not for use with high capacity power poles which come complete with an integral divider 111" long High Capacity Power Pole (Complete) (EPHT) Provides a larger route than the power pole for power and communications from the ceiling to the raceway level of the panel and includes the electrical harness and junction box The length of harness provided is 111" Can not be routed through a glass panel Power Pole Harness (Includes Junction Box) (EPB) Designed for use with pole poles with no harness Available in 11" or 135" lengths which represents the portion of harness encased in flexible conduit an additional 12" of exposed wires is provided on the interior portion of the harness for connection with the raceway to an appropriate receptacle harness The power pole and harness uses one outlet cut out in the panel frame, therefore it cannot be used for power High Capacity Power Pole (No Harness) (EPHTE) Provides a larger route than the power pole but does not include electrical harnesses or a junction box Is equipped with a built-in pole divider so can be used to enclose both electrical harnesses and communication cables

9 base feed basics Transit offers several options for bringing the power to a workstation from the base. They are outlined below. All Base Feeds can be connected to any compatible Receptacle Harness, Panel Pass-Through Harness or Four-Way Connector. They carry power to the raceway level only and additional harnesses are equipped to carry power through to other panels The external section of Base Feed Kits are enclosed in liquid-tight PVC-covered, flexible steel conduit, is 72" long and is designed for hard-wiring. The internal sections, enclosed in flexible steel conduit, are 30" long and must be secured within the panel Base Feed Kits cannot be installed on panels with baseboards Base Feed (BFK) Is hardwired to the building power supply and is installed in the base opening of the panel to feed power up into the panel raceway Strain Relief Internal Section (30" long) Electrical Conduit Support Plate External Section (Liquid-tight 72") Split Base Feed (BFKS) Is hardwired to the building power supply in two places, and is installed in the base opening of the panel to feed power up into the panel raceway Is designed to comply with specific requirements in certain jurisdictions, and is prepared for hard wiring within the floor monument at the base feed junction box Strain Relief Internal Section (30" Long) Electrical Conduit Support Plate External Section (Liquid-Tight 18" or 72" Long) Split Base Feed (BFKP) Can be plugged into the building power supply, and is installed in the base opening of the panel and feeds power up into the panel raceway The only outlet types that may be specified with this system are outlets on circuit 1 ex. Duplex ED11 or ED111 Strain Relief Internal Section (30" long) Electrical Conduit Support Plate External Section 24" or 72"

10 power distribution basics Harnesses and Connectors are available to transport power throughout the panels. Harnesses can make turns around 90 corners Harnesses are equipped with clips that attach to the edge of the raceway and ground the furniture panel Off-Module Jumper (EG) Used when panels are connected offmodule to route power externally for the base of one panel into the base of another Cannot be installed on a panel with a baseboard Four Way Connector (EF) Routes power in three directions for distribution between two to four adjacent panels Outlets cannot be connected to the four-way connector Power comes in through one leg of the connector and is distributed to the remaining three legs Panel Pass Through Harness (EH) Routes power at the raceway level to adjacent panels but does not connect to outlets For use with panels that do not require worksurface height power access The 36" long harness is to be used with 18", 24" and 30" wide panels, and all other sizes require the 66" or 102" harness Receptacle Harness (ES) Routes power to outlets in the panel raceway and carries power through the raceway to adjacent panels The 36" long harness is recommended for use with 18", 24" and 30" wide panels, and the 66" is for all other panel sizes Quadrex Receptacle Harness (ET) Routes power to outlets in 42, and 60 wide panel raceways and carries power through to adjacent panels Allows connection to panels with four knockout locations M-Clip (TMC) Routes cabling and wiring within the panel to maximize the space available for routing Attaches to the horizontal rails behind upper elements and are provided with a standard panel at 36" high extras are only required for mounting at 51", 66", and 81" high No Raceway Jumper (EI) Designed specifically for panels without a raceway. It routes power through the base of the panel Is specifically intended for use with fully glazed panels Enough length should be applied when selecting the size to allow for the harness to drop down the base, travel across the bottom of the panel, and then go back up to raceway height

11 power access basics Outlets can be installed at various heights on a panel either face mounted or accessed through an access door. Outlets are available for all Transit wire systems and connect to any compatible receptacle harness All outlet knockouts in the panel access rail are for triplex outlets, so all duplex outlets are equipped with an adapter plate to allow them to fit Single Double Raceway Box (ERB) Provides face mounted access to power/communications at various heights Consists of two duplex outlets and one communication opening per side, with the communication opening being 1.850" x 2.875" Available as a single or double (access from one side or both sides) two single-sided boxes can go into the panel back-to-back to allow upgrades from single-sided to double-sided Can be mounted at three levels, base, worksurface height and 51" high Communication cables are shielded from power cables Must be specified with a Power/Communication Element Cannot be used with the 8N wiring system Cannot be used in the 18", 24" or 30" wide panel Raceway Box (Separate Neutral) (ERB8N) Provides face mounted access to power/communications at various heights Can only be used with the 8N wiring system Raceway Box (Dual Isolated) (ERB8K) Provides face mounted access to power.communications at various heights Can only be used with the 8K wiring system Single Double Outlets (ED) Provide access to power at worksurface height through the access element The Duplex has two plug in points, and the Triplex has three plug in points Can be used with all wiring systems except 8N and 8K Duplex Triplex Outlets (Separate Neutral) (ED8N) Used only with the 8N Separate Neutral wiring system and provide access to power at worksurface height Surge Suppressor (EDS5) An isolated ground outlet that protects equipment against electrical power surges up to 6000 volts Provides access to power at worksurface height through the access door Equipped with a light that indicates when power is present Outlets (Dual Isolated) (EK8K) Used only with the 8K Dual Isolated wiring system and proves access to power at worksurface height Outlet Knockout Cover (EDC) Covers an outlet opening in the receptacle rail when no outlet is being used

12 communications access basics Transit offers adapters to provide access to communication outlets. Voice & Data Module (VDM) Provides user access to communication connectors at worksurface height Is installed over the communication duct opening in the access area and can accommodate a variety of connectors Voice & Data Faceplate Adapter (EVDF) Allows the installation of modular furniture voice and data faceplates in Decora Faceplate sized cut-outs Voice & Data Adapter (VDA) Provides an interface between the panel and the voice and data module when communications are being brought in from the top of the panel and the VDM is hanging upside down Access Door VDM Plates (DMP) Allows voice and data outlets to be mounted onto the face of the Transit Access Door Element The cover plate DMPC is used to cover the hole in the element when a connector is removed When applying access door VDM Plates wires should be routed trough the strain relief clip to protect voice and data cable connections Base Cable Clips (HBCC) Attach to the base rail of Lyft Thin Panels to support casual wire routing Do not require tools to secure clips Also available: Chicago Corner Ducts (CH) Enclose electrical cables between corner panel connections Are designed to meet electrical requirements for inter-panel connections in Chicago Installed at raceway height where raceways exist, and are not for use with panels without raceways Two-Way 45 Four-Way 90 Two-Way 90 Two-Way 180 Three-Way 180 Straight Connection

13 casual wire basics Transit provides power centers and tray for casual wiring applications. The worksurface and panel trays include a sliding 12" joiner to conceal a continuous run of wires if desired Retractable Power Center (EPC) Is a receptacle that slides up through the worksurface to provide easy access to outlets concealed beneath the surface Retracts completely when not in use allowing full use of the worksurface Includes three electrical outlets and is equipped with a circuit breaker Also available but not illustrated: Joiner Joiner 15" - 87" Worksurface Tray (TZW) Attaches to the rear underside of the worksurface and facilitates wire management along semi-supported worksurfaces Can only be used on straight surfaces When mounted along the depth of a worksurface, the worksurface support must be inset from the edge When attached to a panel mounted worksurface, the tray width must be at least 6 less than the worksurface width to ensure worksurface support clearance 18" - 60" Panel Tray (TZP) Attaches to the face of the panel to provide casual wire management where an access door is not available Can also provide casual wiring distribution to off-module wing panels Can mount at 21", 36", 51" or 66" level of panel, but is most commonly used at 21" high Actual width is 3 less than the panel in order to accommodate worksurface supports 72" - 96" Bridge Tray (TZB) Manages data and communications wire along the bridge, and distributes wires to panels, tables or semisuspended worksurfaces Can be applied to one or both sides of the bridge Actual width of the tray is 4" less than the nominal size