DC562, digital input/output module,

Transcription

1 Ordering Data DATA SHEET DC562 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP R0000 1TNE R3101 1TNE R3102 1TNE R3103 1TNE R3104 1TNE R3105 1TNE R3106 DC562, digital input/output module, 16 configurable inputs/outputs, transistor output Terminal block TA563-9, 9 pins, screw front, cable side, 6 pieces per unit Terminal block TA563-11, 11 pins, screw front, cable side, 6 pieces per unit Terminal block TA564-9, 9 pins, screw front, cable front, 6 pieces per unit Terminal block TA564-11, 11 pins, screw front, cable front, 6 pieces per unit Terminal block TA565-9, 9 pins, spring front, cable front, 6 pieces per unit Terminal block TA565-11, 11 pins, spring front, cable front, 6 pieces per unit *) For planning and commissioning of new installations use modules in status only. 2018/11/12 3ADR010046, 3, en_us 1

2 Technical Data 2 Dimensions The dimensions are in mm and in brackets in inch. 3 Technical Data The System Data of AC500-eCo apply Ä Chapter 4 System Data AC500-eCo on page 5 Only additional details are therefore documented below. Process voltage UP Connections Rated value Current consumption via UP terminal Max. ripple 5 % Inrush current Protection against reversed voltage Current consumption from 24 VDC power supply at the L+/UP and M/ZP terminals of the CPU/bus module Galvanic isolation Isolated groups Terminal 19 for UP (+24 VDC) and terminal 20 for ZP (0 V) 24 VDC 90 ma A per output (max.) A 2 s Yes Ca. 10 ma Yes, between the input/output group and the rest of the module 1 group for 16 channels 2 3ADR010046, 3, en_us 2018/11/12

3 Technical Data of the Digital Inputs/Outputs if Used as Inputs Surge voltage (max.) Max. power dissipation within the module Input data length Output data length Weight Mounting position Cooling 35 VDC for 0.5 s 4.8 W 2 bytes 2 bytes Ca. 125 g Horizontal or vertical The natural convection cooling must not be hindered by cable ducts or other parts in the switchgear cabinet. No effects of multiple overloads No effects of multiple overloads on isolated multi-channel modules occur, as every channel is protected individually by an external fuse. 3.1 Technical Data of the Digital Inputs/Outputs if Used as Inputs Number of channels per module Distribution of the channels into groups 16 configurable inputs (24 VDC) 1 (16 channels per group) Connections of the channels C0 to C15 Terminals 1 to 16 Reference potential for the channels C0 to C15 Indication of the input signals Input type according to EN Input signal range Signal 0 Undefined signal Signal 1 Ripple with signal 0 Ripple with signal 1 Input current per channel Input voltage +24 V Input voltage +5 V Input voltage +15 V Input voltage +30 V Max. permissible leakage current (at 2-wire proximity switches) Input delay (0->1 or 1->0) Max. cable length Shielded Unshielded Terminal 20 (minus pole of the process voltage, name ZP) 1 yellow LED per channel; the LED is ON when the input signal is high (signal 1). The module is powered through the I/O-Bus. Type 1 sink +24 VDC -3 V...+5 V +5 V V +15 V V -3 V...+5 V +15 V V Typ. 5 ma Typ. 1 ma > 2.5 ma < 8 ma 1 ma Typ. 8 ms 500 m 300 m 2018/11/12 3ADR010046, 3, en_us 3

4 Technical Data of the Digital Inputs/Outputs if Used as Outputs 3.2 Technical Data of the Digital Inputs/Outputs if Used as Outputs Number of channels per module Distribution of the channels into groups 16 configurable transistor outputs 1 (16 channels per group) Connections of the channels C0 to C15 Terminals 1 to 16 Reference potential for the channels C0 to C15 Common power supply voltage Indication of the input signals Way of operation Output voltage at signal 1 Output delay (max. at rated load) 0 to 1 50 µs 1 to µs Output current Rated current per channel (max.) Rated current per group (max.) Rated current (all channels together, max.) Lamp load (max.) Max. leakage current with signal 0 Output type Protection type Rated protection fuse (for each channel) Demagnetization when inductive loads are switched off Switching frequency With inductive loads With lamp loads Short-circuit-proof / Overload-proof Overload message Output current limitation Resistance to feedback against 24 VDC signals Connection of 2 outputs in parallel Max. cable length Shielded Unshielded Terminal 20 (negative pole of the process voltage, signal name ZP) Terminal 19 (positive pole of the process voltage, signal name UP) 1 yellow LED per channel; the LED is ON when the input signal is high (signal 1). The module is powered through the I/O bus. Non-latching type UP -0.3 V at max. current 0.5 A at UP 24 VDC 8 A 8 A 5 W < 0.5 ma Non-protected External fuse on each channel 3 A fast Must be performed externally according to driven load specification Max. 0.5 Hz Max. 11 Hz at max. 5 W No No No Yes Not possible 500 m 150 m 4 3ADR010046, 3, en_us 2018/11/12

5 System Data AC500-eCo Creepage Distances and Clearances 4 System Data AC500-eCo 4.1 Environmental Conditions Table 1: Process and Supply Voltages 24 VDC 100 VAC 230 VAC Voltage 24 V (-15 %, +20 %) Protection against reverse polarity Yes Voltage 100 V (-15 %, +10 %) Frequency 50/60 Hz (-6 %, +4 %) Voltage 230 V (-15 %, +10 %) Frequency 50/60 Hz (-6 %, +4 %) VAC wide range supply Voltage 100 V V (-15 %, +10 %) Frequency 50/60 Hz (-6 %, +4 %) Allowed interruptions of power supply, according to EN DC supply Interruption < 10 ms, time between 2 interruptions > 1 s, PS2 AC supply Interruption < 0.5 periods, time between 2 interruptions > 1 s NOTICE! Exceeding the maximum power supply voltage (> 30 VDC) for process or supply voltages could lead to unrecoverable damage of the system. The system could be destroyed. Temperature Humidity Operating Storage -40 C C Transport -40 C C Air pressure Operating Storage 0 C C (horizontal mounting of modules) 0 C C (vertical mounting of modules and output load reduced to 50 % per group) Max. 95 %, without condensation > 800 hpa / < 2000 m > 660 hpa / < 3500 m 4.2 Creepage Distances and Clearances The creepage distances and clearances meet the requirements of the overvoltage category II, pollution degree /11/12 3ADR010046, 3, en_us 5

6 Power Supply Units 4.3 Insulation Test Voltages, Routine Test According to EN V V circuits against 100 V V circuits against 100 V V circuits against 2500 V 1.2/50 µs 1500 V 1.2/50 µs 2500 V 1.2/50 µs 24 V circuits (supply, 24 V inputs/outputs, analogue inputs/ outputs ), if they are electrically isolated against COM interfaces, electrically isolated COM interfaces, electrically not isolated 500 V 1.2/50 µs 500 V 1.2/50 µs Not applicable Not applicable FBP interface 500 V 1.2/50 µs Ethernet 500 V 1.2/50 µs ARCNET 500 V 1.2/50 µs 200 V V circuits against 100 V circuits against 100 V V circuits against 1350 V AC 2 s 820 V AC 2 s 1350 V AC 2 s 24 V circuits (supply, 24 V inputs/outputs, analogue inputs/ outputs), if they are electrically isolated against COM interfaces, electrically isolated COM interfaces, electrically not isolated 350 V AC 2 s 350 V AC 2 s Not applicable FBP interface 350 V AC 2 s Ethernet 350 V AC 2 s ARCNET 350 V AC 2 s Not applicable 4.4 Power Supply Units For the supply of the modules, power supply units according to PELV specifications must be used. 6 3ADR010046, 3, en_us 2018/11/12

7 Electromagnetic Compatibility 4.5 Electromagnetic Compatibility Immunity Immunity against electrostatic discharge (ESD): Electrostatic voltage in case of air discharge Electrostatic voltage in case of contact discharge ESD with communication connectors Immunity against the influence of radiated (CW radiated): Test field strength Immunity against transient interference voltages (burst): Supply voltage units (DC) Supply voltage units (AC) Digital inputs/outputs (24 VDC) Digital inputs/outputs (120 VAC VAC) Analog inputs/outputs CS31 system bus Serial RS-485 interfaces (COM) Serial RS-232 interfaces (COM, not for PM55x and PM56x) ARCNET FBP Ethernet I/O supply, DC-out Immunity against the influence of line-conducted interferences (CW conducted): Test voltage High energy surges According to IEC , zone B, criterion B 8 kv 4 kv, in a closed switch-gear cabinet 6 kv 1 ) In order to prevent operating malfunctions, it is recommended, that the operating personnel discharge themselves prior to touching communication connectors or perform other suitable measures to reduce effects of electrostatic discharges. According to IEC , zone B, criterion A 10 V/m According to IEC , zone B, criterion B 2 kv 2 kv 2 kv According to IEC , zone B, criterion A 3 V zone B, 10 V is also met. Power supply AC 2 kv CM / DM ²) According to IEC , zone B, criterion B Power supply DC CM / 0.5 kv DM ²) DC I/O supply, add. DC-supply-out 0.5 kv CM / 0.5 kv DM ²) Buses, shielded CM ²) AC I/O unshielded 2 kv CM / DM ²) I/O analog, I/O DC unshielded CM / 0.5 kv DM ²) Radiation (radio disturbance) According to IEC 55011, group 1, class A 1 ) High requirement for shipping classes are achieved with additional specific measures (see specific documentation). ²) CM = Common Mode, DM = Differential Mode 2018/11/12 3ADR010046, 3, en_us 7

8 Approvals and certifications 4.6 Mechanical Data Mounting Horizontal Degree of protection IP 20 (if all terminal screws are tightened) Housing According to UL 94 Vibration resistance acc. to EN all three axes (DIN rail mounting) 5 Hz Hz, continuous 3.5 mm 11.9 Hz Hz, continuous 1 g Shock test All three axes 15 g, 11 ms, half-sinusoidal Mounting of the modules: DIN rail according to DIN EN mm, depth 7.5 mm or 15 mm Mounting with screws Screws with a diameter of 4 mm Fastening torque 1.2 Nm 4.7 Approvals and certifications Information on approvals and certificates can be found in the corresponding chapter of the Main catalog, PLC Automation. ABB Automation Products GmbH Eppelheimer Str Heidelberg, Germany Telephone: +49 (0) Fax: +49 (0) plc.support@de.abb.com abb.com/plc Copyright ABB. We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly forbidden. 8 3ADR010046, 3, en_us 2018/11/12