MAGIXBOX TM. Quick Start Guide

Transcription

1 TM TM by TouchMagix MAGIXBOX TM Quick Start Guide

2 What s in the box: Ankle Ceiling Plate Extendable Rod Connector Piece Middle Piece Universal Spider Super clamp with ball socket Safety Cable Projector Mount Top Projector Mount Bottom Adapter Four Arms, Screws and Allen Keys

3 Interactive Wall Setup with Clamp HDMI Cable Wireless Keyboard Assembly Instructions: 1. Select desired location on the ceiling and assemble the projector mount on it. Interactive Wall Setup with separate Projector mount 2. Mount your projector. 3. Attach on the projector mount using Super Clamp. 4. Connect HDMI cable from to the projector. 5. Connect power adapter for and Projector to standard AC outlet. 6. Power on the projector and adjust the display area. 7. Start the software and follow given steps. 8. All set to go. Enjoy the experience.

4 Interactive Floor Setup with Clamp Projector Installation Step 1 Step 2 Rotate to fit in Attach the ceiling plate to the ceiling using the dry wall screws. Fix the extendable bar by rotating it in clockwise. Step 3 Step 4 Interactive Floor Setup with separate Projector mount Attach the four arms to the universal spider using screws and washers. Do not completely tighten the screws yet. Attach the projector to the universal spider using the designated holes to screw in the four arms. Once done make sure all the screws from Step 3 are tightened. Step 5 Carefully hook the ankle atop the universal spider to the middle piece at the end of the extendable bar attached to the ceilings. Tilt the ankle to ensure lens of projector points towards projection surface and tighten the screws on the ankle tightly to hold it firm and steady.

5 Clamping Step 6 Step 7 Step 9 Step 10 MotionMagic Tightly fix in the ball socket head into the designated hole on the by rotating it clockwise. Carefully lift the with the extension arm and use the super clamp to attach it the projector mount fixed to the ceiling. Tighten the super clamp using the long knob till the grip is very firm and steady. Loop the safety cable around the extendable bar as shown and insert and lock the carabiner on the designated whole on the top backside of the. Insert the wireless keyboard s dongle into the s USB port. Step 8 Step 11 HDMI Adjust the angle of the attached using the knob on the ball socket to make sure the sensor is approximately pointed towards the projection surface. Once adjusted, tighten the knob sufficiently to hold the firm and steady. Lock Lock Lock Power Adaptor Power Cable A. Press the button (lock) & simultaneously pull the knob B. Rotate it counterclockwise (while pulling) C. Release the knob & tighten it by rotating it in clockwise direction Connect the and the Projector to power supply and connect them to each other using the HDMI cord.

6 Alternate Setup (When projector is pre-installed) TM powering instructions 1. The TM system automatically powers ON when connected to AC power. 2. On successful booting of the OS, the pre-installed TM software will automatically start. 3. Connect the system to the internet via WiFi. 4. Log In into TM software if you are an existing user OR simply Sign Up to get registered as a new user. 5. If you accidentally shutdown the system, just switch OFF the mains AC power, wait for seconds and switch ON the mains again to Power ON the system. TM English - X Calibration Scheduler Steps: 1. Unscrew the Super clamp from the ball socket rod. Tools Help 2. Unscrew the connector piece and middle piece from the rest of the projector mount. 3. Unscrew the middle piece from the connector piece. 4. Screw in the free end of the ball socket rod into the connector piece and secure it from the other end using a nut. 5. Screw in the to the ball socket end securely. TM by TouchMagix 6. Screw in the new assembly to either the extension rod of the projector mount or the ceiling plate directly.

7 Safety information Your is designed and tested to meet the latest standards of safety for Interactive technology use. However, to ensure your and the device safety, it s important that you read the following safety instructions: Do not use this product near water or a heat source such as a radiator. Openings on the chassis are for ventilation, do not block or cover these openings. Make sure to leave plenty of space around the system for ventilation. Use this product in environments with ambient temperatures between 0 to 55 C. Do not spill water or any other liquid on your system. Do not walk on the power cord or anything to rest on it. Do not look into the lens while the projector is ON. The strong light from the lamp may damage your eyes. Do not overload the power outlet as this can result in fire or electrical shock. If you encounter the following technical problems with the product, unplug the power cord and contact: support@motionmagix.com The system does not function properly even if you follow the operating instructions. The system was stopped or the cabinet is damaged. The power cord or plug is damaged. Liquid has been spilled into the system. The system performance changes. TM by TouchMagix For support, call us at or please visit