Introduction Circuit Protection

Transcription

1 Introduction Circuit Protection Weidmuller s DIN-rail mounted circuit breakers are available for use in applications where circuit protection must be able to distinguish between circuit overloads and short circuits. Each circuit breaker has the ability to be reset without the need to change components. All circuit breakers are available with an assortment of jumpers and marking tags. Circuit breakers in the 9926 Series are culus listed according to UL489 and CSA 22.2 No. 5.02, CE, VDE. The hydraulic magnetic trip mechanism offers,000a of interrupting capacity in 20V and 240V, 50/60Hz applications. The CB2200 Series feature integrated alarm contacts within a narrow profile, thereby allowing increased enclosure capacity. All of these circuit breakers demonstrate consistent reliability through 0% calibration and testing, and feature a touch safe design to prevent injury from accidental contact with live components. CB2200 Series The CB4200 Series of thermal magnetic circuit breakers feature a pushbutton style of trip reset. This reset provides a visual indication of status which allows for rapid troubleshooting. CB4200 Series The CB90 Series of thermal magnetic circuit breakers provide a rugged and industry-standard form factor (8 mm/pole). For supplemental circuit protection. CB90 Series 48

2 Branch Rated Circuit Breakers AC Version Circuit Breakers Hydraulic Magnetic Single pole and double pole versions 20/240 VAC, 50/60 Hz Up to 25A Just 3 mm wide Mounts on 35mm DIN-rail culus listed according to UL489 CSA C22.2 No. 5.02, CE, VDE Ordering Data : (up to 20 VAC) : (up to 240 VAC) (amps) TS 35 Description (amps) TS 35 Description QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM QL--3-DM-KM QL-2-3-DM-KM-25 Voltage 20/240 VAC, 50/60Hz minimum 0.5A maximum 25A Interrupting capacity,000a Dielectric strength 500V, 50/60Hz 0MM Operating life 000 mechanical operations Operating temperature C Wire size* 0.5-5A: 4AWG min., AWG max A: AWG min. 20 in.-lb Approval culus listed according to UL489 CSA C22.2 No. 5.02, CE, VDE Accessories Bus-bar ( pole, insulated, m) Bus-bar (2 pole, insulated, m) Bus-bar end cap, pole Bus-bar end cap, 2 pole Power lug, straight Power lug, Lock-out handle 6793 *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is Trip Curves Hydraulic Magnetic Typical time/current characteristics at 30ºC Sample trip characteristics - KM 25% 50% 200% 400% 600% 800% 00% minimum (sec) maximum (sec) Although the 9926 series uses a magnetic only trip mechanism, CSA testing indicates a trip characteristic similar to thermal magnetic trip mechanisms. No de-rating is required at elevated temperatures. Additional trip curves and amp ratings are available upon request. AC Version - dimensions in mm (in.) 7.4 (2.8) 28.5 (.2) 5 (0.2) 9 (0.75) 32 (.26) 45 (.77) 74 (2.9) 66 (2.6) 64.8 (2.55) AC version Trip Curve Tripping Time Seconds Minutes (0.7) 57 (2.24) Operating Characteristics Curve 3 (0.5) Ambient Temperature 30 C (%) Rated (3.65) Trip Curve applies to the following part numbers where "XX" is the current rating: XX XX AC version Trip Curve Tripping Time 26 (.02) 3 (0.5) Seconds Minutes Operating Characteristics Curve KM Ambient Temperature 30 C (%) Rated

3 Branch Rated Circuit Breakers AC Version with Contacts Circuit Breakers with Auxiliary switch, Trip alarm, Combination of both w/ Auxiliary Contact Trip (Alarm Contact) Combination (Auxiliary & Alarm Contact) AC voltages (20/240V) Single and double pole versions culus listed according to UL489 and C22.2 No. 5.02, CE, VDE Factory fitted auxiliary or trip alarm Compact 6.5mm width Attached to right hand side of circuit breaker Voltage 20/240 VAC, 50/60Hz minimum 0.5A maximum 25A Interrupting capacity,000a Dielectric strength 500V, 50/60Hz 0MM Operating life 000 mechanical operations Operating temperature C Wire size* 0.5-5A: 4AWG min., AWG max A: AWG min. 20 in.-lb Approval culus listed according to UL489 and C22.2 No. 5.02, CE, VDE : Aux (up to 20 VAC) QL-A--3-DM-KM QL-A--3-DM-KM QL-A--3-DM-KM QL-A--3-DM-KM QL-A--3-DM-KM QL-A--3-DM-KM QL-A--3-DM-KM-25 w/ Auxiliary Contact : Trip (up to 20 VAC) QL-T--3-DM-KM QL-T--3-DM-KM QL-T--3-DM-KM QL-T--3-DM-KM QL-T--3-DM-KM QL-T--3-DM-KM QL-T--3-DM-KM-25 Trip (Alarm Contact) : Combo (up to 20 VAC) QL-AT--3-DM-KM QL-AT--3-DM-KM QL-AT--3-DM-KM QL-AT--3-DM-KM QL-AT--3-DM-KM QL-AT--3-DM-KM QL-AT--3-DM-KM-25 Combination (Auxiliary & Alarm Contact) *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is : Aux (up to 240 VAC) QL-A-2-3-DM-KM QL-A-2-3-DM-KM QL-A-2-3-DM-KM QL-A-2-3-DM-KM QL-A-2-3-DM-KM QL-A-2-3-DM-KM QL-A-2-3-DM-KM-25 : Trip (up to 240 VAC) QL-T-2-3-DM-KM QL-T-2-3-DM-KM QL-T-2-3-DM-KM QL-T-2-3-DM-KM QL-T-2-3-DM-KM QL-T-2-3-DM-KM QL-T-2-3-DM-KM-25 : Combo (up to 240 VAC) QL-AT-2-3-DM-KM QL-AT-2-3-DM-KM QL-AT-2-3-DM-KM QL-AT-2-3-DM-KM QL-AT-2-3-DM-KM QL-AT-2-3-DM-KM QL-AT-2-3-DM-KM-25 AC version Trip Curve Dual Mount Dimensions in mm (in.) Trip Curves Hydraulic Magnetic Typical time/current characteristics at 30ºC Additional trip curves and amp ratings are available upon request. Tripping Time Seconds Minutes0 Operating Characteristics Curve KM Ambient Temperature 30 C 57.0 (2.24) 26.2 (.03) (N/O)6 (N/C)8 (C)5 3.3 (.23) (C) 2(N/C) 4(N/O) 2.3 (0.84) 32.9 (.3) 2. (0.83).7 (0.42) TRIP ALARM Q. CNECTORS (0.08) 0.5 (0.02) 5.5 (0.22) AUX SWITCH Q. CNECTORS 2.8 (0.) 0.5 (0.02) 7 (0.28) (%) Rated 50

4 Branch Rated Circuit Breakers DC Version Circuit Breakers Hydraulic Magnetic Single pole versions only U2 trip curve for general purpose applications 80 and 25 VDC Up to 60A Just 3 mm wide Mounts on 35mm DIN-rail UL 489A listed VDE (80 VDC) (25 VDC) Ordering Data : (80 VDC) QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U QY--3-DM-U2-60 : (25 VDC) QY--3-DM-U2-0-B QY--3-DM-U2-02-B QY--3-DM-U2-03-B QY--3-DM-U2-04-B QY--3-DM-U2-05-B QY--3-DM-U2--B QY--3-DM-U2-5-B QY--3-DM-U2-20-B QY--3-DM-U2-25-B QY--3-DM-U2-30-B QY--3-DM-U2-35-B QY--3-DM-U2-40-B QY--3-DM-U2-45-B QY--3-DM-U2-50-B QY--3-DM-U2-60-B Accessories DC version Trip Curve Dimensions in mm (in.) Bus-bar ( pole, insulated m) Bus bar end cap, pole Power lug, straight Power lug, Lock-out handle 6793 Trip Curves Hydraulic Magnetic Typical time/current characteristics at 30ºC Additional trip curves and amp ratings are available upon request. 74 (2.9) 66 (2.6) 7.9 (0.7) 3 (0.5) Voltage 80,25 VDC minimum 0.5 A maximum 60 A Interrupting capacity,000 A Dielectric strength 500 V, 50/60 Hz 0 MM Operating life 000 mechanical operations Operating temperature C Wire size* -5A: 4 AWG min., AWG max A: AWG min. 20 in.-lb Approval UL 489A Listed, CE, VDE Tripping Time Seconds Minutes Operating Characteristics Curve U2 DC (4% Ripple Factor) Ambient Temperature 30 C (%) Rated (2.8) 28.5 (.2) 5 (0.2) 9 (0.75) 32 (.26) 45 (.77) 64.8 (2.55) 57 (2.24) 92.8 (3.65) *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is

5 Supplemental Circuit Breakers Circuit Breakers Hydraulic Magnetic Triple Pole AC Voltages 277/480V Trip curve 2 for general purpose applications UL 77 recognized VDE approved and CE marked Just 3 mm wide Mounts to 35 mm DIN-rail Factory fitted auxiliary or trip alarm Single, double and triple pole versions Ordering Data Accessories : (up to 277 VAC) : (up to 480 VAC) : Triple Pole (up to 480 VAC) Rating Rating QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ-3-3-D QZ--3-D QZ-2-3-D QZ--3-D QZ-2-3-D QZ--3-D QZ-2-3-D QZ--3-D QZ-2-3-D QZ--3-D QZ-2-3-D QZ--3-D QZ-2-3-D QZ--3-D-2-60 Supplemental dimensions in mm (in.) Bus bar ( pole, insulated m) Bus bar (2 pole, insulated m) Bus bar (3 pole, insulated m) 6797 Bus bar end cap, pole Bus bar end cap, 2 pole or 3 pole Power lug, straight Power lug, Lock-out handle (0.86) 65 (2.56) 60 (2.36) 25.9 (0.94) 45 (.77) 3 (0.5) 92.8 (3.65) 26 (.02) 39 (.54) 44 (.73) 3 (0.5) 3 (0.5) 5.0 (0.2) 63.8 (2.5) 73 (2.87) Voltage 277/480 50/60 Hz minimum 0.5 A maximum 60 A Interrupting capacity 5 277/480 V, 5 20 V, V Dielectric strength 500 V, 50/60 Hz 0 MM Operating life 000 mechanical operations Operating temperature C Wire size* -5A: 4 AWG min., AWG max A: AWG min. 20 in.-lb Approval UL 77 Recognized, VDE (EN ) Approved, CSA C22.2 No. 235, CE Marked Supplemental Trip Curve Trip Curves Hydraulic Magnetic Typical time/current characteristics at 30ºC Additional trip curves and amp ratings are available upon request. Tripping Time Seconds Minutes0 0.0 Operating Characteristics Curve 2 Ambient Temperature 30 C *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit).the SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is (%) Rated curus recognized to UL77 and C22.2 No

6 Supplemental Circuit Breakers with Contacts Circuit Breakers Auxiliary switch, Trip alarm, Combination of both w/ Auxiliary Contact Trip (Alarm Contact) Combination (Auxiliary & Alarm Contact) AC Voltages 277/480V Trip curve 2 for general purpose applications UL 77 recognized VDE approved and CE marked Just 3 mm wide Mounts to 35 mm DIN-rail Factory fitted auxiliary or trip alarm Single, double and triple pole versions Voltage 277/480 50/60 Hz minimum 0.5 A maximum 60 A Interrupting capacity 5 277/480 V, 5 20 V, V Dielectric strength 500 V, 50/60 Hz 0 MM Operating life 000 mechanical operations Operating temperature C Wire size* -5A: 4 AWG min., AWG max A: AWG min. 20 in.-lb Approval UL 77 Recognized, VDE (EN ) : Aux (up to 277 VAC) QZ-A--3-D QZ-A--3-D QZ-A--3-D QZ-A--3-D QZ-A--3-D QZ-A--3-D QZ-A--3-D-2-25 w/ Auxiliary Contact : Trip (up to 277 VAC) QZ-T--3-D QZ-T--3-D QZ-T--3-D QZ-T--3-D QZ-T--3-D QZ-T--3-D QZ-T--3-D-2-25 Trip (Alarm Contact) : Combo (up to 277 VAC) QZ-AT--3-D QZ-AT--3-D QZ-AT--3-D QZ-AT--3-D QZ-AT--3-D QZ-AT--3-D QZ-AT--3-D-2-25 Combination (Auxiliary & Alarm Contact) Approved, CSA C22.2 No. 235, CE Marked *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags.the part number for adhesive SchS2 is Supplemental Trip Curve Trip Curves Hydraulic Magnetic Typical time/current characteristics at 30ºC 00 Operating Characteristics Curve 2 : Aux (up to 480 VAC) QZ-A-2-3-D QZ-A-2-3-D QZ-A-2-3-D QZ-A-2-3-D QZ-A-2-3-D QZ-A-2-3-D QZ-A-2-3-D-2-25 : Trip (up to 480 VAC) QZ-T-2-3-D QZ-T-2-3-D QZ-T-2-3-D QZ-T-2-3-D QZ-T-2-3-D QZ-T-2-3-D QZ-T-2-3-D-2-25 : Combo (up to 480 VAC) QZ-AT-2-3-D QZ-AT-2-3-D QZ-AT-2-3-D QZ-AT-2-3-D QZ-AT-2-3-D QZ-AT-2-3-D QZ-AT-2-3-D-2-25 Tripping Time 0. Seconds Minutes0 Ambient Temperature 30 C Triple Pole w/ Auxiliary Contact Triple Pole Trip ( Alarm Contact) Triple Pole Combination (Auxiliary & Alarm Contact) (%) Rated curus recognized to UL77 and C22.2 No. 235 : Triple Pole Aux (up to 480 VAC) QZ-A-3-3-D QZ-A-3-3-D QZ-A-3-3-D QZ-A-3-3-D QZ-A-3-3-D QZ-A-3-3-D QZ-A-3-3-D-2-25 : Triple Pole Trip (up to 480 VAC) QZ-T-3-3-D QZ-T-3-3-D QZ-T-3-3-D QZ-T-3-3-D QZ-T-3-3-D QZ-T-3-3-D QZ-T-3-3-D-2-25 : Triple Pole Combo (up to 480 VAC) QZ-AT-3-3-D QZ-AT-3-3-D QZ-AT-3-3-D QZ-AT-3-3-D QZ-AT-3-3-D QZ-AT-3-3-D QZ-AT-3-3-D

7 Supplemental Circuit Breakers GFCI Ground Fault Interrupt CE approved UL77 and UL53 recognized Small frame size (26mm wide) Single pole plus switched neutral ground leakage protection Trip point is unaffected by ambient temperature ratings up to 50A Trip indication (mid trip handle position) Trip curve 2 for general purpose applications GFCI Ordering Data : GFCI QF7A CB W/GFI QF7A25 - CB W/GFI QF7A255 - CB W/GFI QF7A CB W/GFI QF7A CB W/GFI QF7A CB W/GFI QF7A CB W/GFI GFCI dimensions in mm (in.) 73 (2.87) 65 (2.56) Standard Ampere (A) 5 to 50A Sensitivity (ma) 30 (CE) / 22 (UL) Number of Poles + N Equipment Ground Leakage/GFCS Rated Voltage (V) 230 (CE) / 240 (UL) Rated Interrupting/ 5 ka Withstand Capacity (ka) Weight (kg) 0.26 Trip Curve (standard) 2 Operating Temperature -40 to +65ºC Approval UL 77 and UL 53, CE AC version Trip Curve Trip Curves Hydraulic Magnetic Typical time/current characteristics at 30ºC Tripping Time Seconds Minutes0 0.0 Operating Characteristics Curve 2 Ambient Temperature 30 C 93 (3.66) 82.4 (3.24) 26 (.02) 44 (.73) 68.8 (2.7) 7.8 (0.307) 57 (2.24) 6.4 (0.646) 8.0 (0.35) (2.8) 26 (.02) (%) Rated 35.7 (.406) 54

8 Mounting Options and Accessories Mounting Options If the product is not vertically mounted in the normal DIN-rail mounting orientation, a rating factor must be applied. Figure shows a diagram of the rating factor to apply. The published curves for these circuit breaker products are produced with the circuit breaker in the vertical mounting position. The rating factor only applies to the must hold and must trip points of the curve as the other parts (instantaneous trip point) stay largely unaffected. 95% 45 UP 93% HORIZ 45 UP 95% It is important to note that in environments that are exposed to a high degree of vibration, the cables that connect to the circuit breaker must be securely held in place, as the breaker is not designed to carry the weight of the cables. A maximum of 35N can be applied to the terminal area, in a direction perpendicular to the mounting axis. 0% VERT DOWN 45 HORIZ DOWN 45 VERT 0% 5% 5% Accessories 7% Rating 80A max. Voltage 500V max. Short Circuit Strength 25kA Bus bar ( pole, insulated m) Bus bar (2 pole, insulated m) Bus bar (3 pole, insulated m) 6797 Bus bar end cap, pole Bus bar end cap, 2 pole or 3 pole Rating 85A max. Wire Size AWG min., 4 AWG max. Dimensions A: 6 mm B: 32 mm Power lug, straight Power lug, Part Number Table - Example To order Circuit Breaker Rating of.0 amp Internal Resistance per Pole of. ohms Trip Curve M, Medium (Standard) Amperage "00" - 0.5A "0" - A "02" - 2A / "60" - 60A Trip Curves (s 5-9) "0" - Branch AC KM (Standard) "" - Branch AC OP (Instantaneous) "2" - Branch AC (Fast) "3" - Supplemental 9 (Slow) "4" - Branch 80VDC (Fast) "5" - Supplemental 2 (Standard) "6" - Branch 25VDC OP (Instantaneous) "7" - Branch 80VDC OP (Instantaneous) "8" - Branch 25VDC U2 (Standard) "9" - Branch 80VDC U2 (Standard) Poles Pole 2 Pole 3 Pole "5" - Base Breaker "6" - With Auxiliary Contact "7" - With Trip Alarm Contact "8" - Combo Aux/Trip Contact "9" - GFCI Lock-out handle 6793 Amperage "00" - 0.5A "0" - A "02" - 2A / "60" - 60A Trip Curves ( 4) "0" - Supplemental (Fast) Poles Pole 2 Pole 3 Pole "4" - Base Breaker 55

9 CB4200 Series Supplemental Circuit Breakers Circuit Breakers Thermal Magnetic Rated from 0.05 to 6.0 amps Available in single or double pole configurations Features a tease free design to reduce contact damage Offers push button trip/reset function Trip free design means the breaker cannot be held closed against a fault Mounts on 32mm* or 35mm DIN-rail UL 77 recognized CB4200 Series CB4200 Series Ordering Data : : TS 35 TS 35 *For TS 32 Rail, *For TS 32 Rail, (amps) see adapter below (amps) see adapter below Trip Curves Thermal Magnetic Typical time/current characteristics at 23ºC CB4200 Series M to 7.5 A M+ 8 to 6 A *Adapter foot dimensions in mm (in.),000, C +23 C +55 C,000, C +23 C +55 C (.787) TS32 adapter times rated current times rated current 56

10 CB4200 Series Supplemental Circuit Breakers CB4200 Series Internal Wiring Diagram Dimensions in mm CB4200 Series Internal Wiring Diagram Dimensions in mm Rated voltage & current Creepage resistance Dielectric strength Interrupting capacity (VDE 0660, Part, P-2) Interrupting capacity; 420 (UL 77/EN PC) UL CSA VDE Voltage AC 250 V, DC 65 V, 50/60 Hz A AC 250 V, DC 65 V, 50/60 Hz A AC 250 V, DC 65 V, 50/60 Hz A PTI 600 to IEC 2 4,000 VAC; IEC 664 & 664 A > 0 MM (DC 500 V) 420- Maximum capacity A Self-limiting 2 A 200 A A 400 A Rated current Rated voltage Maximum capacity A AC 250 V 200 A A AC 250 V 200 A 20 A AC 25 V 400 A Typical life at 2 x rated current Shock Vibration Temperature range Corrosion Humidity Weight Wire size (UL) 5,000 operations 25 g ( ms) to IEC , Test Ea.2 Nm 5 g (57 to 500 Hz / ±0.38 mm, to 57 Hz) to IEC , Test Fc -30 C +55 C (-22 F +3 F) 96 hours at 5% salt spray, to IEC 68-2-, Test Ka 240 hours at 95% RH, to IEC , Test Ca 60 g per pole #20 8 AWG solid/0.5 6 mm 2 Accessories Jumpers Adapter foot (for TS 32 Rail) Marking Tags Note: Part numbers are shown for a single card of pre-printed tags numbered -50. Daisy Chain 50* Straight CQB** insulated Angled CQB** insulated Special print only Consecutive horizontal Consecutive vertical BDC CQB CQB CQB CQB CQB CQB CQB CQB MCBAF/TS WS 8/5 MC *** DEK 5/ DEK 5/ Note: Resistive and inductive loads ( A) *BDC will accommodate 20 A per pin, 20 A total **CQB will accommodate 8 A per pin, 8 A total; dedicated to 420 Series ***Please specify horizontal or vertical print when ordering. Standard quantity = 44 tags per card. 57

11 CB2200 Series Supplemental Circuit Breakers Circuit Breakers Thermal Magnetic CB2200 Series CB2200 Series CB2200 Series Triple Pole Rated from 0. to 32.0 amps Available in single, double and triple pole configurations Offers normally open (N/O) and normally closed (N/C) auxiliary contacts Lever-switch trip/reset function Mounts on 32mm or 35mm DIN-rail UL 77 recognized Ordering Data : * : : Triple Pole N/O Aux. N/O-N/C N/O-N/C (amps) (amps) (amps) *All part numbers with N/O Auxiliary Contacts on each pole when the main breaker contact is open (in the position) Ordering Data : : : Triple Pole All part numbers with N/C Auxiliary Contacts on each pole when the main breaker contact is open (in the position) (amps) (amps) (amps)

12 T CB2200 Series Supplemental Circuit Breakers CB2200 Series Trip Curves Thermal Magnetic Typical time/current characteristics at 23ºC CB2200 Series,000,000 F 0. to 32 A 30 C +23 C +55 C times rated current -M 0. to 7.5 A,000, C AC +23 C DC +23 C +55 C 0 Dimensions in mm Rated voltage & current UL Voltage 277 / 480 VAC (50/60 Hz); 65 VDC A 0. DC CSA 277 / 480 VAC (50/60 Hz); 65 VDC A 0.0 AC VDE 250 / 45 VAC / 65 VDC A Auxiliary contacts 250 VAC / 65 VDC, A times rated current Creepage resistance PTI 600 to IEC 2 Dielectric strength Interrupting capacity (VDE 0660, Part, P-2) 3,000 VAC; IEC 664 & 664 A > 0 MM (DC 500 V) Rated current Rated voltage Rupture capacity (3 times) A 250 / 45 VAC 400 A,000,000 -M 8 to 32 A 30 C AC +23 C DC +23 C +55 C 6 32 A 250 / 45 VAC 800 A 0 Interrupting capacity (UL 77/EN PC) Rated current Rated voltage Max. rupture capacity (3 times) 0. 6 A 277 / 480 VAC 5000 A A 277 / 480 VAC 2000 A A 65 VDC 2000 A 0. DC Typical life at 2 x rated current Shock Vibration Temperature range Corrosion Humidity Weight Wire size (UL) Nm (lb. in.) Accessories Jumpers Daisy Chain 50 Busbars 5,000 operations 25 g ( ms) to IEC , Test Ea 0.6 (5.3) Auxiliary contact: 0.5 (4.4) 5 g (57 to 500 Hz / ±0.38 mm, to 57 Hz) to IEC , Test Fc C (-22 F +40 F) 96 hours at 5% salt spray, to IEC 68-2-, Test Ka 240 hours at 95% RH, to IEC , Test Ca Approximately 60 g per pole max 6 mm 2 8 AWG max.5 mm 2 4 AWG (Aux. contact) BDC 50, 20 A maximum pole (CB2200) pole (CB2200) ,000, AC times rated current -T 0. to 7.5 A 30 C +23 C +55 C 0.0 Marking Tags Note: Part numbers shown are for a single card of pre-printed tags numbered -50. Special print only Consecutive horizontal Consecutive vertical DEK 5/ * DEK 5/ DEK 5/ times rated current -T 8 to 32 A Note: Resistive and inductive loads ( A) *Please specify horizontal or vertical print when ordering.,000, C +23 C +55 C times rated current 59

13 CB90 Series Supplemental Circuit Breakers Circuit Breakers Thermal Magnetic CB90 Series CB90 Series CB90 Series Triple Pole Rated from 0.5 to 63 amps Available in single, double and triple pole configurations Optional auxiliary contacts Mounts on 35mm DIN-rail UL and CSA approvals CSA 277 VAC ( pole) or 480 VAC (2 and 3 pole) 50 VDC (0.5 A to 50 A) pole VDC (0.5 A to 50 A) 2 pole Ordering Data : : : Triple Pole (amps) (amps) (amps) Trip Curves Thermal Magnetic Typical time/current characteristics at 23 C CB90 Series M 0.5 to 6 A M AC to 40 A M AC 63 A,000,000, C 23 C 23 C,000,000, times rated current times rated current times rated current 60

14 CB90 Series Supplemental Circuit Breakers CB90 Series pole pole 3 pole Dimensions in mm Internal Wiring Diagram Rated voltage & current UL 77 CSA C 22.2 No. 235 VDE Creepage resistance Interrupting capacity (UL 77/EN PC) pole Mechanical/Electrical endurance Shock Vibration Temperature range - operating Weight Strip length Auxiliary contact rating Wire size - #22 2 AWG Wire size 277 V ( pole) 480 V (2 and 3 pole) 50 VDC ( pole) VDC (2 pole) 277 V ( pole) 480 V (2 and 3 pole) 50 VDC ( pole) VDC (2 pole) PTI 250 to IEC 2 >0 MM at 500 VDC ratings Interrupting Rupture capacity (3X) Voltage A,000 A (UL) 277 VAC/50 VDC A 2,000 A (UL) 277 / 480 AC A 6,000 A (UL) 50 VDC () pole A 6,000 A (UL) VDC (2) poles 20,000/, g ( ms) 2 Nm 3 g ( to 55 Hz) -25 C C (-3 F to 3 F) pole (30 g); 2 pole (280 g); 3 pole (430 g) 2 mm Voltage AC 220/240 5 A AC A DC 24 V 4 A DC 60 V A DC220 V 0.4 A #8 2 AWG (line); #8 3 AWG (load) 69 Auxiliary Contact Modules Accessories Jumpers Auxiliary contacts SPDT Side/Middle 3 pole bus, x mm, buses (9) 3 phase groupings 80A/0A pole bus, 6 x 2 mm, buses (4) 3 phase groupings 20A/30A pole bus, 6 x mm, buses (9) 3 phase groupings 20A/30A pole bus, 2 x 2 mm, buses 2 breakers 80A/0A pole bus, 2 x 2 mm (insulated), buses 2 breakers 63A Bus bar clamp 30A Auxiliary contacts Internal Auxiliary Wiring Diagram 4 2 Security hardware Lock out cover Marking Tags Adhesive label ETO /26, yellow (26 mm x mm)