LS 5000 series Vibration Level Switch for liquids
|
|
- Ada Berry
- 5 years ago
- Views:
Transcription
1 Vibration Level Switch for liquids Set-up without adjustment Integrated fault monitoring Unaffected by product variations in density, conductivity, dielectric constant or viscosity Insensitive to foam, pressure and temperatures variations Insensitive to external vibrations Operating temperature up to 250 C (optional) Status: 10/99
2 Vibration Level Switch for liquid Overfill or dry-run protection Suitable for applications in confined spaces (fork length only 40mm) Electronics replaceable under process conditions Operating Principle The tuning fork is piezoelectrically energised and vibrates at its mechanical resonance frequency of approx Hz. The piezoelectric elements are fastened mechanically and are therfore not subject to temperature shock limitations. When the tuning fork is immersed in the product, the frequency changes. This change is detected by the integrated oscillator and converted into a switching command. The models LS 5100 and LS 5150 are short versions without extension, whereas LS 5200 and LS 5250 can be ordered with extension tubes. The level switches LS 5150 and LS 5250 have a polished surface especially suitable for applications in hygienic industries. Housing Aluminium (plastic coated) plastic Process connection Thread G 3 /4 A, 3/4 NPT, G 1 A and 1 NPT Flanges from DN 25 or ANSI 1 Hygienic fittings LS 5200/5250 Electronics Non-contact switch Floating relay output Floating transistor output Two-wire current output Two-wire current output acc. to NAMUR LS 5100/5150 Tube extension up to 4000 mm length Tuning fork material Stainless steel (316L) also polished up to Ra 0,5 µm Hastelloy C4 (2.4610) ECTFE coated Enamelled 2
3 The responsibility as to the suitability, intended use and corrosion-resistance of the materials used in their construction rests solely with the purchaser. Technical data Process conditions Product temperature ( / Hastelloy C4) C ( F) Product temperature with temp. adapter of (option) LS 5000 series of / Hastelloy C C ( F) LS 5000 series enamelled C ( F) LS 5000 series ECTFE coated C ( F) Operating pressure max 64 bar (928 psi) Dep. on mechanical connection Product viscosity (dynamic) mpas Product density g/cm 3 Materials Housing PBT (Polyester), Aluminium (plastic coated) Tuning fork (316L) or (Hastelloy C4), Hastelloy C4 enamelled, with ECTFE coated Flanges , with Hastelloy C4 plated, enamelled steel, ECTFE coated Extension tube (316L) or (Hastelloy C4), Hastelloy C4 enamelled, with ECTFE coated Adapters Temperature adapter Gastight leadthrough (option) / glass (not ExD) Length Tuning fork 40 mm Extension tube (LS 5200 / 5250) Steeel , (Hastelloy C4) mm Hastelloy C4 enamelled mm ECTFE coated mm Surface quality (option) Standard (LS 5100 / 5200) Ra approx. 3.0 µm Polished (LS 5150 / 5250) Ra 1.5 µm Hygienic version (3A/FDA) (LS 5150 / 5250) Ra 0.5 µm Process connection Thread G 3 /4 A, 3 /4 NPT, G1A or 1 NPT PN 64 Flange DIN DN 25, ANSI 1 Hygienic fittings Bolting DN 40 PN 40 Tri-Clamp 1, 1 1 /2 PN 10 Cone DN 25 PN 40 Tuchenhagen Varivent DN 50 PN 10 Electronics SW E60N (EX) Supply For connection to separator acc. to NAMUR, approx. 8.2 V Open circuit voltage Approx. 8.2 V Short-circuit current Approx. 8.2 ma Output Two-wire NAMUR output Current consumption Characteristics falling 2.2 ma uncovered/ 1 ma covered Characteristics rising 1 ma uncovered/ 2.2 ma covered Fault signal 1 ma SW E60Z (EX) Supply voltage V DC (via signal conditioning instrument SU 501) Output Two-wire output Current consumption Approx. 8 ma empty/ approx. 16 ma full SW E60C,R,T (EX) Supply voltage V AC, 50/ 60 Hz or V DC Output Contactless electronic switch Internal current Requirement approx. 3 ma (via load circuit) Load current Min. 10 ma; max. 400 ma Protection class DIN IP 66 / IP 67 Approvals As overfill protection in conformity with WHG (Germany) Accessories Welding socket For thread of with O-ring in front, optionally with welding mark for defined fork alignment. 3
4 Mounting instructions Vertical installation from top, from bottom Horizontal installation Switching point Switching point with lower density Switching point approx. 13 mm Switching point with higher density Switching point recommended installation position for adhesive products: Switching point Top marking Vibrations Lateral load Extreme vibrations and shocks can cause the extension tube to vibrate. Therefore provide a fastening or straining directly above the tuning fork to fasten the extension tube. Make sure that the vibrating element is not subjected to lateral forces. Mount the instrument at a location in the vessel where no interfering effects can occur. The surface of the tuning fork should be parallel to the product movement. Moisture Turn the cable entries of horizontally mounted instruments downwards to avoid moisture ingress. For this purpose the plastic housing can be rotated by approx For vertically installed instruments, loop the cable connected to the instrument housing downwards so that rain and condensation water can drain off. Marking of welded socket Marking Thread starting point is defined. Remove therefore the supplied seal from the thread. This seal is not required when using a welded socket. Screw the level switch into the welded socket. The welded socket has a notch. Weld this socket with the notch facing upwards, or in the case of pipelines, aligned with the direction of flow. 4
5 Electrical connection Two-wire NAMUR output (SW E60N) SW E60N Ex Two-wire output (SW E60Z) SW E60Z Ex NAMUR (IEC ) + 0,5 g / cm V DC 0,5 g / cm ,7 g / cm ,7 g / cm Switching ampfifier acc. to NAMUR (IEC ) 1 A Contactless electrical switch (SW E60C) Floating realy output (SW E60R) SW E60C SW E60R + L V AC/DC max 400mA + L N N A 12 0,5 g / cm V DC V AC + L N A B 0,5 g / cm 3 0,7 g / cm B 0,7 g / cm Power supply: V AC, 50/60 Hz V DC (for further information, see installation manual) Power supply: V AC, 50/60 Hz V DC (for further information, see technical data) 1 2 5
6 Floating transistor output (SW E60T) V DC SW E60T PNP NPN + + out max 400mA A 0,5 g / cm 3 The responsibility as to the suitability, intended use and corrosion-resistance of the materials used in their construction rests solely with the purchaser. Power supply: V DC (for further information see the following connection examples as well as the technical data) B 0,7 g / cm 3 For direct control of relays, contactors, magnet valves, warning lights, horn, as well al PLC inputs Connection examples NPN action PNP action NPN action PNP action NPN action PNP action The transistor switches the supply voltage of the oscillator to the binary input of a PLC or to an electrical load. Trough different connection of the cunsumer (load). PNP or NPN action can be preset. Control of alternating current loads The transistor switches a second, galvanically isolated voltage source to the binary input of a PLC or to an electrical load. Trough different connection of the cunsumer (load). PNP or NPN action can be preset. The transistor switches a second voltage source with the same reference potential to the binary input of a PLC or to an electrical load. Trough different connection of the cunsumer (load). PNP or NPN action can be preset. The transistor switches a galvanically separated alternating voltage V AC to a load. 6
7 Dimensions LS 5000 series 7
8 Dimensions LS 5000 series 8
9 Dimensions LS 5000 series 9
10 Ordering Code LS 5100/5200 Vibrating level switch for liquids for LS 5100 for LS
11 Length of the extended probe for the LS 5200 only Total length in mm Length (L) mm (min. 150 mm; max mm) Table: Process Connection Type / Process Connection Size / Process Connection and fork material for LS 5100/
12 Ordering Code LS 5150/5250 Vibrating level switch for liquids and for hygienic applications Fork surface roughness : Ra < 1.5 µm or RA < 0.5 µm for LS 5150 for LS
13 Length of the extended probe for the LS 5250 only Total length in mm Length (L) mm (min. 150 mm; max mm) Table 1: Process Connection Type / Process Connection Size / Process Connection and fork material for LS 5150/
Operating Instruction
Level and Pressure Operating Instruction VEGASWING 71 A Contents Contents Safety information... 2 1 Product description 1.1 Function and configuration... 3 1.2 Functional principle... 3 1.3 Technical data...
More informationOPTISWITCH 4000 C 5100 C, 5150 C 5200 C, 5250 C
Level detection in liquids Vibration OPTISWITCH 4000 C 500 C, 550 C 500 C, 550 C Data Sheet Contents Contents Description of the measuring principle.... Type overview.... 6 Mounting information... 8 4
More informationTechnical Data Sheet. OPTISWITCH 5000 series Vibration Level Switch. for liquids
Technical Data Sheet KROHNE 01/2006 7.02395.26.00 CMD OPTISWITCH 5000 series Vibration Level Switch for liquids Integrated fault monitoring Unaffected by product variations in density, conductivity, dielectric
More informationOperating Instructions OPTISWITCH 5200 C, 5250 C with relay output
Operating Instructions OPTISWITCH 5200 C, 5250 C with relay output Contents Contents 1 About this document 1.1 Function... 4 1.2 Target group... 4 1.3 Symbolism used... 4 2 For your safety 2.1 Authorised
More informationAssembly. 1 Compact version with valve plug 2 Short tube version with cable 3 Compact version with M12 plug 4 Short tube version with M12 plug
Vibration Limit Switch Features Limit switch for liquids External function test with test magnet Onsite function check possible thanks to LED indication Large selection of process connections for hassle-free
More informationNIVOSWITCH VIBRATING FORK LEVEL SWITCHES
For liquids and solids NIVOSWITCH VIBRATING FORK LEVEL SWITCHES OUR PROFESSION IS YOUR LEVEL LEVEL SWITCHES O U R P R O F E S S I O N I S NIVOSWITCH VIBRATING FORK LEVEL SWITCHES MAIN FEATURES and mini
More informationTechnical Data Sheet. OPTISWITCH 3000 series Vibration level switch. for solids
Technical Data Sheet KROHNE 04/2005 7.02541.21.00 GR OPTISWITCH 3000 series Vibration level switch for solids Highly robust tuning fork Insensitive to build-up Set-up without filling Detection of solids
More informationFOR LIQUIDS AND SOLIDS
FOR LIQUIDS AND SOLIDS LEVEL SWITCHES VIBRATING FORK LEVEL SWITCHES O U R P R O F E S S I O N NIVOSWITCH VIBRATING FORK LEVEL SWITCHES MAIN FEATURES and mini compact type Rod extension up to 3 meters (10
More informationTechnical Data Sheet. OPTISWITCH 3000 series Vibration level switch. for solids
Technical Data Sheet KROHNE 04/2005 7.02541.21.00 GR OPTISWITCH 3000 series Vibration level switch for solids Highly robust tuning fork Insensitive to build-up Set-up without filling Detection of solids
More informationLiquiphant T FTL20. Technical Information. Level limit switch for liquids
Technical Information Liquiphant T FTL0 Level limit switch for liquids Application The Liquiphant T FTL0 is a level limit switch for all kinds of fluids and is used in tanks, containers and pipelines.
More informationOperating Instructions April 2008 SITRANS LVL200S
Operating Instructions April 2008 SITRANS LVL200S Content Content 1 About this document 1.1 Function............................. 4 1.2 Target group.......................... 4 1.3 Symbolism used.......................
More informationOperating Instructions April 2008 SITRANS LVL200E
Operating Instructions April 2008 SITRANS LVL200E Content Content 1 About this document 1.1 Function............................. 4 1.2 Target group.......................... 4 1.3 Symbolism used.......................
More informationLevel. Conductive. Level detection. Overview Page 142 VEGAKON series 60 Page 144 EL 1 EL 8 Page 148 Limit switches VEGATOR Page 157
Conductive Level detection Level Overview Page 142 VEGAKON series 60 Page 144 EL 1 EL 8 Page 148 Limit switches VEGATOR Page 157 141 VEGAKON Proven compact limit switches Measuring principle and applications
More informationFloat Switches with Permanent Magnet For Vertical Installation Model RSM
Level Measurement Float Switches with Permanent Magnet For Vertical Installation Model RSM WIKA Data Sheet LM 30.01 Applications Level measurement for almost all liquid media Pump/level control and monitoring
More informationVibration. Level detection
Vibration Level detection 5 Overview Page 116 VEGASWING 51 Page 120 VEGASWING series 60 Page 122 VEGAVIB series 60 Page 128 VEGAWAVE series 60 Page 134 Accessory Page 140 Level switches VEGATOR Page 144
More informationCapacitance level switches LS 210 LS 220
KROHNE 03/2001 7.02374.31.00 GR/PRINTO Capacitance level switches Compact switches for liquids, solids, slurry, foam and interface; outstanding performance for a low price Easy to install, no moving parts,
More informationAssembly. Function 41
Capacitive limit switch Features Assembly Limit switch for liquids and bulk solids Device with rod probe Complete unit consisting of the probe and electronic insert Integrated active build-up compensation:
More informationMagnetic float switch For vertical installation Model FLS
Level measurement Magnetic float switch For vertical installation Model FLS WIKA data sheet LM 30.01 for further approvals see page 3 Applications Level measurement for almost all liquid media Pump and
More informationTECHNICAL INFORMATION Vibracon LVL-A7
PROCESS AUTOMATION TECHNICAL INFORMATION Vibracon LVL-A7 Vibration Limit Switch Limit Switch for Liquids ISO900 With regard to the supply of products, the current issue of the following document is applicable:
More informationFloat switch For the process industry
Level measurement Float switch For the process industry Model FLS (models with E approval: 60, AL-ADF) KSR data sheet LM 30.01 for further approvals see page 3 Applications Level measurement for almost
More informationLiquipoint T FTW 31, FTW 32 Level limit switch for multiple point detection in conductive liquids
Technical Information Level limit switch for multiple point detection in conductive liquids Applications The Liquipoint T sensors are used in conductive liquids (down to 0 µs/cm) for determining level
More informationA TECHNOLOGY FOR EVERY LEVEL APPLICATION
INSTRUCTION MANUAL A TECHNOLOGY FOR EVERY LEVEL APPLICATION NIVOSWITCH R0/R500 VIBRATION FORK LEVEL SWITCHES Dual purpose level switch with intelligent electronics applicable for: almost all liquids light,
More informationCapacitive. Overview 116 VEGACAP series VEGACAP 27, 35, Capacitive VEGACAP
Capacitive Overview 116 VEGACAP series 60 120 VEGACAP 27, 35, 98 132 Capacitive VEGACAP 115 VEGACAP Level detection in bulk solids and liquids Measuring principle Sensor and vessel form the two electrodes
More informationLiquipoint T FTW31, FTW32
TI00375F/00/EN/14.16 71336942 Products Solutions Services Technical Information Liquipoint T FTW31, FTW32 Conductive Point level switch for multiple point detection in conductive liquids Applications The
More informationLS 6600 Technical Datasheet
Technical Datasheet Switch for level detection and dry-run protection Optimised sensor geometry, easy to clean Measures products with dielectric constant > 1.5 Small and compact KROHNE 06/2011-4001367301
More informationVane wheel probe BFA25 for flow measurement of gases and liquids with integrated, configurable transducer UFA in Ex-d housing
Vane wheel probe BFA25 for flow measurement of gases and liquids with egrated, configurable transducer UFA in Ex-d housing Drawing 5 Vane wheel flow probe BFA25 (Dimensions see Page 3) Measurable variables
More informationTechnical Information Liquiphant FTL31
TI047F/00/EN/0.6 7589 Products Solutions Services Technical Information Liquiphant FTL Vibronic Point level switch for liquids Application The Liquiphant FTL is a point level switch for liquids and is
More informationFloat Switches with Permanent Magnet For Horizontal Installation Model HIF
Level Measurement Float Switches with Permanent Magnet For Horizontal Installation Model HIF WIKA Data Sheet LM 30.02 Applications Level measurement for almost all liquid media Pump/level control Chemical
More informationOPTISWITCH 6600 C Technical Datasheet
Technical Datasheet Microwave Level Switch for standard hygienic applications Optimised sensor geometry, easy to clean Measures products with dielectric constant > 1.5 Small and compact KROHNE CONTENTS
More informationTECHNICAL INFORMATION Vibracon LVL-B1, LVL-B2
PROCESS AUTOMATION TECHNICAL INFORMATION Vibracon LVL-B1, LVL-B2 Vibration Limit Switch Limit Switch for Bulk Solids ISO9001 With regard to the supply of products, the current issue of the following document
More informationTemperature Measurement SITRANS TS300
Siemens AG 018 For food, pharmaceuticals and biotechnology modular design Dimensional drawings Cable gland M1x1.5 for cable Ø 3... 6.5 (0.1... 0.6) Ø 60 (.36) Ø d = N + H 1 Ø 50.5 (1.99) U X H 1 N H Ø
More informationJUMO PINOS L01. Calorimetric flow sensor. Brief description. Special features. Customer benefits. Data Sheet
sales@jumo.co.uk info.us@jumo.net Page 1/9 JUMO PINOS L01 Calorimetric flow sensor Brief description The JUMO PINOS L01 flow sensor serves the measuring and monitoring of flow velocities of water and aqueous
More informationLevel measurement. Applications. Special features. Description
Level measurement Optoelectronic level switch Model OLS-S, for the process industry (with Ex i approval: KSR-OPTO.21*06XX) Model OSA-S, switching amplifier (with Ex i approval: KSR-OPTO.2502.XX) KSR data
More informationLevel measurement CleverLevel LBFI Point level detection
User Product benefits highlights Safe detection of liquids, bulk solids and powders Short immersion length Capable of differentiation between foam and liquid Insensitive to adherent or sticky media Status
More informationTechnical Information Liquipoint FTW23
TI0202F/00/EN/04.6 736230 Products Solutions Services Technical Information Capacitance point level measurement Point level switch for liquids in the food and beverage industry Application The is a point
More informationLevel measurement CleverLevel LBFH Point level detection
Product highlights User benefi ts Safe detection of liquids, bulk solids and powders Short immersion length Ecellent cleanability Capable of differentiation between foam and liquid Insensitive to adherent
More informationAssembly. Connection FEL 52 (E5) 3-wire DC connection (example) FEL 52 (E5) 0.5 A U V DC V DC
Vibration Limit Switch Features Assembly Level limit switch for liquids Large selection of process connections: universal use Wide variety of electronic modules (e. g., relay, thyristor signal output):
More informationLevel sensor for monitoring the level of liquid media
Level sensor MG Level sensor for monitoring the level of liquid media Characteristics Level sensor output 4 20mA or Resistance output in three-wire potentiometer circuit Temperature range: -30 C to 150
More informationTechnical Information Liquipoint FTW33
TI008F/00/EN/0.5 78677 Products Solutions Services Technical Information Liquipoint FTW Conductive and capacitance point level measurement Point level switch for liquid and pasty media in the food and
More informationLevel sensor with reed measuring chain Model FLR, for the process industry
Level measurement Level sensor with reed measuring chain Model FLR, for the process industry WIKA data sheet LM 20.02 for further approvals see page 3 Applications Level measurement for almost all liquid
More informationLevel sensor Magnetostrictive, high-resolution measuring principle Models FFG-P, FFG-T, FFG-TP, FLM-H
Level measurement Level sensor Magnetostrictive, high-resolution measuring principle Models FFG-P, FFG-T, FFG-TP, FLM-H KSR data sheet FFG-P, FFG-T, FFG-TP, FLM-H Applications High-accuracy level measurement
More informationRosemount 2110 Compact Vibrating Fork Liquid Level Switch
Product Data Sheet Rosemount 2110 Rosemount 2110 Compact Vibrating Fork Liquid Level Switch Function virtually unaffected by flow, turbulence, bubbles, foam, vibration, solids content, coating, properties
More informationApplication The DA03 serves as indicator of differential. Follow mounting instructions in accordance to application.
DA03 Differential Pressure Gauge / Differential Pressure Gauge and Switch Models for Assignment in Explosion-hazardous Areas per Directive 94/9/EC (ATEX) Application The DA03 serves as indicator of differential
More informationLevel measurement CleverLevel LBFI Point level detection
Product highlights User benefi ts Safe detection of liquids, bulk solids and powders Short immersion length Capable of differentiation between foam and liquid Insensitive to adherent or sticky media Status
More informationLevel switch NS 10/NS 25..-AM
Level switch NS 10/NS 25..-AM Fluidcontrol Oil tanks in lubrication and oil supply systems are often under overpressure compared to the ambient atmosphere. All oil moistened parts of devices mounted externally
More informationTemperature Switches
ETS 00 Series Temperature Switch for Inline and Tank Mounting Applications Description The ETS 00 is a compact electronic temperature switch with 4-digit digital display. Pressure resistant to 8700 psi,
More informationPressure transmitter/pressure switch PASCAL CS
Pressure transmitter/pressure switch PASCAL CS for food/pharmaceutical/biotechnology,type series CS2110 Features Multifunctional pressure transmitter/pressure switch Hygienic case with no notches or indentations
More informationLevel sensor Stainless steel version Model RLT-1000, for industrial applications
Level measurement Level sensor Stainless steel version Model RLT-1000, for industrial applications WIKA data sheet LM 50.02 Applications Level measurement of liquids in machine building Control and monitoring
More informationFloat switch For the process industry, lateral installation with external chamber Model ELS
Level measurement Float switch For the process industry, lateral installation with external chamber Model ELS KSR data sheet LM 30.03 for further approvals see page 2 Applications Mounting on engines,
More informationSoliphant M FTM50, FTM51, FTM52
Technical Information Soliphant M FTM50, FTM51, FTM52 Level limit switch Universal vibration limit switch for powder and fine-grained bulk solids, also for explosion-hazardous areas Application The Soliphant
More informationTechnical Information Minicap FTC260, FTC262
TI00287F/00/EN/16.16 71312209 Products Solutions Services Technical Information Minicap FTC260, FTC262 Capacitive Point level switch with buildup compensation No calibration necessary Application The Minicap
More informationFlexBar HRT Pressure Transmitter
FlexBar HRT Pressure Transmitter 4...0 ma, -wire transmitter, HART communication Some hygienic connections conform to -A standards, FDA demands and EHEDG guidelines Configurable span, unit and damping
More informationDigital electropneumatic positioner
Digital electropneumatic positioner Type 879 can be combined with Compact metal housing Graphic display with backlight Easy start-up Comprehensive range of additional software functions Profibus DPV1 (optional)
More informationGladiator. Vibration Smart Switch Series. Data Sheet. A Higher Level of Performance. A level switch for liquids and solids.
A Higher Level of Performance Data Sheet Gladiator Vibration Smart Switch Series A level switch for liquids and solids For more information, please visit > www.hawkmeasure.com Overview The Gladiator Smart
More informationTemperature measurement TER8 Front-flush and low-invasive resistance thermometers
Product highlights 3-A fulfillment without elastomers Front-flush or immersed types Accurate reading independent on ambient temperature Fast response time Hermetically sealed towards process Capable of
More informationAssembly. max Example: 2-wire connection IH More connection types see section electrical connections. Auxiliary voltage.
Guided Level Radar Features Measurement independent of density, temperature, and dust Measurement also possible with foam on the surface Simple, menu-guided on-site operation with four-line plain text
More informationMaterial pressure (bar) (Cv (US) kv x 1,2 Seat
00 / poppet valves electromagnetic actuated, directly controlled G /, / NPT or flanged with NAMUR Interface TÜV-approval based on IEC 6 08, DIN V Valves for safety systems up to SIL Solenoid valve also
More informationElectronic pressure switch with display For sanitary applications Model PSA-31
Electronic pressure measurement Electronic pressure switch with display For sanitary applications Model PSA-31 WIKA data sheet PE 81.85 Applications Food and beverage industry Pharmaceutical industry Filling
More informationSupplementary instructions. Plug connector Harting HAN 7D. For point level sensors. Document ID: 34456
Supplementary instructions Plug connector Harting HAN 7D For point level sensors Document ID: 446 Contents Contents For your safety.... Appropriate use.... General safety instructions.... Safety instructions
More informationInstallation Instructions Temperature transmitter TAA /00 06/2011
Installation Instructions Temperature transmitter TAA431 706042/00 06/2011 Contents 1 Functions and features...3 2 Installation...4 2.1 Addressing...4 2.2 Mechanical installation...4 2.3 Connection to
More information02/11/2015
DIN Rail Mount 35 mm HSV Part number 84874320 Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - 3-wire PNP or NPN, Namur, voltage 0-30V or volt-free contact
More informationCapacitive Limit Detection minicap FTC 260, FTC 262
Technical Information TI 287F/00/en Capacitive Limit Detection minicap FTC 260, FTC 262 Compact switch for limit detection with active build-up compensation No calibration necessary Version available for
More informationselection of special materials is available to handle almost any fluid.
For Pressure Transmitters and Bourdon Tube Pressure Gauges Types 839 X Chemical Seals for Various Applications Advantages / Benefits Separation of medium and measuring device in difficult applications
More informationSeries 100. Mechanical Switches Contents. Series 100 Multiple Position Switches
Contents Series 00 Multiple Position Switches Full size housing Full size switch elements DIN 43697 Up to 2 positions IO-Link Quick change plunger block Inductive Inductive with extended range 2 or 6 mm
More informationInstallation, Operation & Maintenance Instructions / Technical Document
Installation, Operation & Maintenance Instructions / Technical Document Model VHL Mini Vibrating Fork Point Level Sensor for Liquids Thank you for purchasing the Model VHL Mini Vibrating Fork Point Level
More informationFlow Measurement SITRANS F M
Overview Mode of operation The flow measuring principle is based on araday s law of electromagnetic induction according to which the sensor converts the flow into an electrical voltage proportional to
More informationFlow measurement FlexFlow PF20S Flow sensor for industrial applications
Product highlights Parallel measurement of flow and temperature Flow measurement independent of the mounting position Large measuring range up to 400 cm/s Measurement at high media temperatures up to 125
More informationPressure transmitter/pressure switch PASCAL CS
Pressure transmitter/pressure switch PASCAL CS for food/pharmaceutical/biotechnology, Type series CS2110 Features Multifunctional pressure transmitter/pressure switch Hygienic case with no notches or indentations
More informationFaults on the system Proximity switch connection technology:
Speed monitor for connection to a base unit from the PNOZmulti modular safety system Approvals Unit features Monitoring of 2 independent axes Connection of 2 incremental encoders or 4 proximity switches
More informationInductive dual sensor For rotary actuators NI4-DSU35TC-2Y1X2/S933
ATEX category II 2 G, Ex zone 1 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Rectangular, housing DSU35 Plastic, PP-GF30-VO Two outputs for monitoring the position of rotary actuators Mounting
More informationRotary Measuring Technology Absolute encoders, Singleturn, Profibus-DP
Safety-Lock TM High rotational speed Temperature High IP High shaft load capacity Shock/vibration resistant Magnetic field proof Short-circuit proof Reverse polarity protection Reliable Increased ability
More informationInductive sensor BI1.5-EG08-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationMultiturn absolute encoder
Release date: 207-0-2 :0 Date of issue: 207-0-2 t79_eng.xml Model Number Features Industrial standard housing Ø58 mm PROFINET IRT 0 Bit multiturn Servo or clamping flange Network loop through by means
More informationRHM160. Coriolis Mass Flow Meter for High Flow Terminal and Pipeline Applications. Features. Applications. Benefits
RHM160 Coriolis Mass Flow Meter for High Flow Terminal and Pipeline Applications Features Standard Pressure ratings up to 50bar (725 psi) Temperature ratings from -196 to 120 C (-320 to 248 F) Mass flow
More informationInductive sensor NI3-EG08K-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Threaded barrel, M8 x 1 Stainless steel, 1.4427 SO DC 2-wire, nom. 8.2 VDC Output acc. to DIN EN 60947-5-6 (NA- MUR)
More informationInductive sensor BI1.5-EG08-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationContact Dial Thermometers
Data sheet 6852 Page 1/11 Contact Dial Thermometers FL 21 Special features Class 1.5 Display range -4 C to +6 C Temperature controller with actual value display as built-in or add-on device in a stainless
More informationDigital electropneumatic positioner
Digital electropneumatic positioner Type 879 can be combined with Compact metal housing Graphic display with backlight Easy start-up Comprehensive range of additional software functions Profibus DPV1 (optional)
More informationThread length. 27 (40) mm. 27 (44) mm. 27 (40) mm. 34 (50) mm. 34 (49) mm. 39 (60) mm. 39 (54) mm. 44 (65) mm. 44 (59) mm
Long Distance Cylindrical. Extra long for increased protection and sensing performance triple proximity sensors for flush mounting requirements. designed and tested for extra long life. Ordering Information
More informationLevel gauges Series LS Level indicator, switch and transmitter for liquids
Level gauges Series LS Level indicator, switch and transmitter for liquids Simple construction Resistant under extreme temperature and pressure conditions No risk of leakage Measuring range: from 150 mm
More informationSM9000. Magnetic-inductive flow meter. Made in Germany
Made in Germany Application Application totaliser function; empty pipe detection; for industrial applications Installation connection to pipe by means of an adapter Media conductive liquids; water; hydrous
More information... f l o w measurement & control...
... f l o w measurement & control... ELECTROMAGNETIC FLOWMETERS OPEN CHANNEL MAGNETIC FLOWMETER PARTLY FILLED PIPE MAGNETIC FLOWMETER VENTURI & PARSHALL FLUMES ULTRASONIC LEVEL MEASUREMENT ULTRASONIC OPEN
More informationVariable Area Flowmeters Installation Instructions G Series and M Series
Variable Area Flowmeters Installation Instructions G Series and M Series Safety Definitions Potential danger to life or of serious injuries. Potential for personal injury from electrical shock. Safety
More informationIndicating Digital Transmitter for Differential Pressure and Flow. Media 6 with LCD Media 6 with LED
Indicating Digital Transmitter for Differential Pressure and Flow Media 6 with LCD Media 6 with LED Application Microprocessor-controlled transmitter for measuring and indicating the differential pressure
More informationInductive sensor For rotary actuators NI4-DSU35TC-2Y1X2/S933
ATEX category II 2 G, Ex zone 1 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationSM9000. Made in Germany
Made in Germany Product characteristics Magnetic-inductive flow meter Connector Process connection: G2 flat seal connection to pipe by means of an adapter Function programmable Totaliser function Empty
More informationOperating Instructions for Level Switch for Liquids. Model: RFS
Operating Instructions for Level Switch for Liquids Model: RFS 1. Contents 1. Contents... 2 2. Note... 3 3. Instrument Inspection... 3 4. Regulation Use... 3 5. Operating Principle... 4 6. Use in Hazardous
More informationThread length (overall length) material
Cylindrical Proximity Sensor for Mobile Usage Designed and tested to keep your machines moving IP69k tested and certified for highest water resistance e1 type approval (according to automotive directive
More informationMANUAL Vibracon LVL-A7
PROCESS AUTOMATION MANUAL Vibracon LVL-A7 Vibration Limit Switch Limit Switch for Liquids ISO900 With regard to the supply of products, the current issue of the following document is applicable: The General
More informationElectronic pressure switch with display For sanitary applications Model PSA-31
Electronic pressure measurement Electronic pressure switch with display For sanitary applications Model PSA-31 WIKA data sheet PE 81.85 Applications Food and beverage industry Pharmaceutical industry Filling
More informationMPreC - Pressure Relief Device Order specification sheet
- Pressure Relief Device Order specification sheet -Series LARGE MESSKO PRESSURE RELIEF DEVICE Complete the Order-N o by choosing the specific add-on s: e.g.: LMPRD 685-08-22-N01-00 Order-N o : Parameter
More informationImmersion Temperature Sensors
1 782 1782P01 Symaro Immersion Temperature Sensors QAE2164 QAE2174 Active sensors for acquiring the water temperature in pipes and tanks Operating voltage AC 24 V or DC 13535 V Signal output DC 010 V or
More information24 V DC typ. 0,65 W. Liquid level with conductive probes (type SK1, SK5) Resistance measurement E1-E0, E2-E0, E3-E0, E4-E0
monitoring in conductive liquids 4 probe inputs for level monitoring Multifunction Adjustable sensor voltage Supply voltage 24-240V AC/DC Protective separation of measuring circuit 3 normally open contacts
More informationFlow Measurement SITRANS F M
low sensor MAG P Overview Mode of operation The flow measuring principle is based on araday s law of electromagnetic induction according to which the sensor converts the flow into an electrical voltage
More informationPneumatic Control/Feedback
897 /Feedback Type 897 can be combined with... Compact design Integrated pilot valve with manual override Internal control air routing Automatic end position adjustment With ATEX II cat. G/D and cat. D/G
More informationGeneral Specifications
General Specifications Model RAGH Rotameter This type of Rotameter is designed for measurement of liquids and gases. The conical glass metering tube has a free rotating float. The mounting position is
More informationGladiator. Vibration Smart Switch Series. Data Sheet. Overview. A Higher Level of Performance. A level switch for liquids and solids
Gladiator Admittance Smart Switch Series A Higher Level of Performance Data Sheet Gladiator Vibration Smart Switch Series A level switch for liquids and solids For more information, please visit > www.hawkmeasure.com
More informationPneumatic Control/Feedback
897 /Feedback Type 897 can be combined with... Compact design Integrated pilot valve with manual override Internal control air routing Bright LED position indicator Automatic end position adjustment Type
More informationCombiTemp TFRN/TFRH. Operating instructions. Temperature sensor. Operating Instructions: EN.
EN/2017-04-03 Design and specifications subject to change without notice English page 1 8 Field of application CombiTemp TFRx is a temperature sensor, based on RTD technology, which is designed and produced
More informationC-Flow Coriolis Mass Flow Meter
Coriolis Mass Flow Meter Application and Features For fluids (e.g. PU components, paints) and gases of high density Suitable for aggressive and contaminated media Measurement of mass flow, density, temperature
More information