Product Manual MNX10043 REV A MODEL DSB. Dual Sensor Modular Switch box
|
|
- Colleen Underwood
- 5 years ago
- Views:
Transcription
1 Product Manual MNX10043 REV A MODEL DSB Dual Sensor Modular Switch box
2 Contents Section I Overview Introduction Description 2 DSB Model Selection.. 2 Section II Installation Mounting Instructions Cable Entry/Exit. 5 Electrical Connections... 6 Section III Operation Operating Procedure.. 8 Section IV Maintenance General. 9 Warranty 9 Figures Figure 1 (Selection Guide). 2 Figure 2 (Mounting). 3 Figure 3 (Earth Ground) Figure 4 (Conduit Entry). 4 Figure 5 (DSB Series Input Wiring).. 5 Figure 6 (DSB Series Input/Output Wiring). 5 Figure 7 (Standard Plugs, No Continuous Output) 6 Figure 8 ( T Plugs with Continuous Output).. 7 Figure 9 (Module Layout) /25/2013 1
3 Section I Overview Introduction This document contains information on the operation, installation and maintenance of the DSB Series. This manual is an overview of the system and references the specific component manuals. User manuals are provided with the system for all configurable internal components. Description The DSB Series is a common cable termination point for bringing dual axis sensor cables into a switch box for routine data collection with portable data collectors. The DSB can have up to 8 dual axis sensors wired for data collection. DSB Model Selection The DSB Series Switch Box has options available to customize the system to your specific needs. Below is a guide to help select which DSB Series switch Box fits your specific requirements. 10/25/2013 2
4 Section II Installation Mounting Instructions The DSB Series Switch Box is contained within a fiberglass or stainless steel junction box enclosure, NEMA 4X rated. Mounting brackets are built into the enclosure for wall mounting. (Wall anchoring screws are not included). Note: If you have purchased a switch box without cable entries provided, you should add your own entry prior to mounting the switch box. Note: CTC does not recommend putting holes in the top of the switch boxes due to access and moisture concerns. Ensure the shield ground wire on the DSB Series Switch Boxes (Fiberglass Enclosures) is connected to earth ground. Note: The DSB Series switch boxes (Stainless Steel Enclosures) are internally grounded to the enclosure. Note: For DSB Series Switch Boxes (Fiberglass Enclosures), customer is required to supply wire from ground to shield ground lug, located on the outside of the enclosure. 10/25/2013 3
5 For DSB Series Switch Boxes (Stainless Steel Enclosures): When mounting the switch box to an earth grounded structure (such as an I-Beam), a shield ground wire is not necessary since the switch box is grounded internally to the enclosure. For DSB Series Switch Boxes (Stainless Steel Enclosures): When mounting the switch box to a non-grounded structure, ensure the shield ground wire or customer supplied ground wire is tied to a source of earth ground. If you are running conduit to your switch box, ensure the conduit cable entry enters from the bottom of the enclosure when mounted. Note: To ensure moisture will not flow into the switch box, a hole should be drilled at the lowest point in the conduit to provide drainage for any moisture. Cable Entry/Exit Figure 3 Earth Ground Cables enter and exit the enclosure through conduit fittings and/or cord grips on the bottom of the unit. All input wiring is routed through either a 1 conduit fitting or cord grips (1 per sensor). All output wiring is routed through either a 1 conduit fitting or cord grips (1 per sensor). 10/25/2013 4
6 Sensor Inputs Figure 5 DSB Series Input Wiring Continuous Output Sensor Inputs Electrical Connections Figure 6 DSB Series Input/Output Wiring Connect sensor cables to the bottom of the module as shown. The terminal blocks can be un-plugged for easier wiring. 10/25/2013 5
7 Input signal options are: Temperature and Dynamic Acceleration Biaxial Sensor Dual Vibration with 4-20mA Output and Dynamic output Temperature and Dynamic Acceleration: Socket A Positive (+ RED) connection for the dynamic acceleration, signal available on BNC A Socket B Positive (+ WHITE) connection for the voltage output for temperature, signal available on BNC B Socket C Negative (- BLACK) connection for the dynamic acceleration and volt output for temperature Socket GND Shield/Drain wire connection that is directed to Earth ground Biaxial Sensor: Socket A Positive (+ Green ) connection for the X axis acceleration, signal available on BNC A Socket B Positive (+ White) connection for the Z axis acceleration, signal available on BNC B Socket C Negative (-Black) connection for both the X and Z axis channels Socket GND Shield/Drain wire connection that is directed to Earth ground Sensor Input Figure 7 Standard Plugs, No Continuous Output 10/25/2013 6
8 Dual Vibration with 4-20mA output and Dynamic outputs: Socket A Positive (+ WHITE) connection for the dynamic acceleration, signal available on BNC A Socket B Positive (+ RED) PLC connection for the 4-20mA signal Socket C Negative (- BLACK) PLC connection for the dynamic acceleration and 4-20mA velocity output Socket GND Shield/Drain wire connection that is directed to Earth ground PLEASE NOTE: PLC connection is made on the continuous output connections of the supplied T plug connector as follows, PLC positive (+) connection on continuous output socket B and PLC negative (-) connection on continuous output socket C. Continuous Output Sensor Input Figure 8 T Plugs with Continuous Output 10/25/2013 7
9 Section III Operation Operating Procedure Once the sensors are attached correctly to the inputs, the unit is ready for use. Access the signal from the sensors through either the 2 pin or 3 pin connector or the BNC terminal s. 3 Pin Connector BNC Connectors Switch T Plug Figure 9 Module Layout 10/25/2013 8
10 Section IV Maintenance Once the system has been installed it requires minimal maintenance. Basic checks to ensure system integrity should be made periodically. Visual inspections should include examinations for the following: No visible electrical burns or smoke inside the enclosure Enclosure hinges are free from rust and securely latched No moisture or condensation build up inside the enclosure General There are no customer replaceable parts. The product has been designed for trouble-free service under normal operating conditions. Warranty If any CTC vibration analysis hardware product should ever fail, we will repair or replace it at no charge. CONTACT INFORMATION: Connection Technology Center, Inc (CTC) 7939 Rae Blvd. Victor, NY (US & Canada) (International) 10/25/2013 9
PRO VPR100 Series ViPR Multi Channel Monitoring System
PRO VPR100 Series ViPR Multi Channel Monitoring System Operation & Maintenance Manual 590 Fisher Station Drive Victor, NY 14564 (800) 999-5290 (585) 924-4650 Internet: www.ctconline.com E-mail: sales@ctconline.com
More informationProximity Probe Accessories
Proximity Probe Accessories Connector Protector Installation Tools MNX10079 REV B 5/10/2016 1 CONTENTS Section 1 : Overview... 3 Introduction... 4 Description..4 Product Selection Guide... 4 Section 2:
More informationCTC Compatible Products for Commtest Instruments
CTC Compatible Products for Commtest Instruments Unconditional Lifetime Warranty If any CTC Vibration Analysis Hardware product should ever fail, we will repair or replace it. General Purpose Accelerometers
More informationDX3309 / DP1009 / DD / DC1009 Series
DX3309 / DP1009 / DD100980 / DC1009 Series FFv Proximity Probe Assembly MNX10071 REV C 11/6/2017 1 CONTENTS Section 1 : Overview... 4 Introduction... 4 Description... 4 Section 2: Probe Details... 5 Proximity
More informationVibraLINK switchable junction boxes Installation and operating guide VLL series
VibraLINK switchable junction boxes Installation and operating guide VLL series Caution: This guide should be read carefully before installation Wilcoxon Sensing Technologies 8435 Progress Drive, Frederick,
More informationIndustrial enclosures. Unparalleled time savings and improved reliability with a new generation of vibration monitoring enclosures
Industrial enclosures Unparalleled time savings and improved reliability with a new generation of vibration monitoring enclosures Enclosures Designed with the user in mind, enabling quick and safe data
More informationWiring guide for dual-output vibration and temperature sensors
Wiring guide for dual-output vibration and temperature sensors Wilcoxon manufactures three types of sensors that output a vibration signal and a DC voltage proportional to the temperature. The temperature
More information12-Bit 0-5 Volt Input Adapter (Part # S-VIA-CM14)
(Part # S-VIA-CM14) The 12-Bit 0-5 Volt Input Adapter is used for measuring voltage levels and is designed to work with the HOBO Weather Station and Micro Station data loggers. The input adapter also provides
More informationOPERATION MANUAL. CMCP310 Series Switch Boxes REV. A
OPERATION MANUAL CMCP310 Series Switch Boxes REV. A 5-27-2009 Model Description: The CMCP310 Series Switchable BNC Boxes are designed for terminating and switching the outputs of up to 48 sensors. Switchboxes
More informationModel 206 Operating Instructions. Setra Systems, Inc. 159 Swanson Road, Boxborough, MA
Model 206 Operating Instructions Setra Systems, Inc. 159 Swanson Road, Boxborough, MA 01719 800.257.3872 www.setra.com 1.0 General Information Every Model 206 has been tested and calibrated before shipment.
More informationES-600 Ozone Controller Operation Manual
ES-600 Ozone Controller Operation Manual Questions about your product? Find answers here: Web: www.ozonesolutions.com/es-600 Phone: 712-439-6880 Ozone Solutions OZONE CONTROLLER Model ES-600 Instructions
More informationBTU 4 & Sensors. Installation and Operation Manual
BTU 4 & Sensors Installation and Operation Manual Table of Contents Introduction... 1 Sensors... 1 BTO Outdoor Sensor... 1 BTI Indoor Sensor... 2 BTS Stack Sensor... 2 Installation... 3 BTU 4 Burk Temperature
More informationINTERCOM AMBULANCE/RESCUE VEHICLE MODEL ICA100 SURFACE MOUNT SERIES MODELS ICA200, ICA300 FLUSH MOUNT SERIES MODELS ICA400, ICA500
Document Number: XE-ICA1PM-R0A ICA100 Rev171109 INTERCOM AMBULANCE/RESCUE VEHICLE MODEL ICA100 SURFACE MOUNT SERIES MODELS ICA200, ICA300 FLUSH MOUNT SERIES MODELS ICA400, ICA500 ICA100 ICA200/300 ICA400/500
More informationInstruction Manual. M Pump Motor Controller. For file reference, please record the following data:
Instruction Manual M Pump Motor Controller For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your
More informationLNX Series Motor and Drives
LNX Series Motor and Drives Operator's Manual PN 04-01808 x PRECISION MOTION CONTROLS 2530 Berryessa Rd. #209 San Jose, CA 95132 1 2 Table of Contents Page Introduction 1. Description 3 2. Warranty 4 Installation
More informationConnecting a Cisco Input Module
CHAPTER 4 Overview The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to ten input devices. Each
More informationAI-102. IR Illuminator. Installation Guide. Rev IP Surveillance
AI-102 IR Illuminator Installation Guide Rev. 1.1 IP Surveillance Revision History: Rev. 1.0: Initial release Rev. 1.1: Changed effective IR range and power consumption. AI-102 Tube Type Infrared Illuminator
More informationPulse Input Adapters (Part # S-UCC/D-M006) for use with HOBO H21 and H22 Series Data Loggers
s (Part # S-UCC/D-M006) for use with HOBO H21 and H22 Series Data Loggers The s are used to log the number of switch closures per interval and are designed to work with smart sensor-compatible HOBO data
More informationEco Sensors OZONE CONTROLLER Model OS-6 Instructions for Use. General and New Features
Eco Sensors OZONE CONTROLLER Model OS-6 Instructions for Use General and New Features The OS-6 is an industrial grade Ozone controller and monitor. The OS-6 design has been optimized for accuracy, ease
More informationPXC Compact Unitary Equipment Controller (UEC)
Document No. 553-169 PXC Compact Unitary Equipment Controller (UEC) Product Description The PXC Unitary Equipment Controller (UEC) is an MS/TP device that can be configured as a programmable, stand-alone
More informationMobileView Junction Box
Installation Instructions MobileView Junction Box (Catalog Number 2727-MRJB2) English The MobileView Junction Box (2727-MRJB2) integrates the following terminals into the control system: MobileView Guard
More informationMODEL SW6000 & SM6100 CENELEC INSTRUCTIONS
MODEL SW6000 & SM6100 CENELEC INSTRUCTIONS Installation Manual 1180 METRIX Experience Value 8824 Fallbrook Dr. Houston, TX 77064, USA Tel: 1-281-940-1802 After Hours Technical Assistance: 1-713-702-8805
More informationEco Sensors OZONE CONTROLLER Model OS-6 Instructions for Use. General and New Features
Eco Sensors OZONE CONTROLLER Model OS-6 Instructions for Use General and New Features The OS-6 is an industrial grade Ozone controller and monitor. The OS-6 design has been optimized for accuracy, ease
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationConnecting a Cisco Output Module
CHAPTER 5 Overview The optional Cisco Output Module (Figure 5-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to 8 outputs, each of which
More informationSensors and Systems. Short Form. that protect your plant...
Sensors and Systems Short Form that protect your plant... About Us Who are Hansford Sensors? At Hansford Sensors, we design, develop and manufacture a wide range of high performance industrial accelerometers,
More informationInstalling Sentor. Hardware Installation
Remote base site monitoring and control Installing Sentor Hardware Installation Copyright 2000 Sentor Monitoring Systems Pty Ltd Contents: 1 Introduction... 1 2 Sentor GUI... 2 3 ST3000 Controller... 3
More informationInstallation RA5112-C-16A-C20. Basic Rack Power Distribution Unit
Installation RA5112-C-16A-C20 Basic Rack Power Distribution Unit Contents Before You Begin........................1 Safety and grounding information..........1 How to Install the Rack PDU...............2
More informationZC-OH5 TAMPER-RESISTANT INDOOR/OUTDOOR HOUSING INSTRUCTION MANUAL FOR USE WITH GANZ ZC-D5000 SERIES MINIDOME CAMERAS
ZC-OH5 TAMPER-RESISTANT INDOOR/OUTDOOR HOUSING INSTRUCTION MANUAL FOR USE WITH GANZ ZC-D5000 SERIES MINIDOME CAMERAS Please carefully read and observe all instructions and warnings contained in this manual
More information120 VAC 18x16x8 Inch Weatherproof Enclosure with Mounting Plate, Cooling Fans and Solid State Fan Controllers Model: NB FS
120 VAC 18x16x8 Inch Weatherproof Enclosure with Mounting Plate, Cooling Fans and Solid State Fan Controllers Model: NB181608-10FS Applications and Features Features: Molded Fiberglass Reinforced Polyester
More informationEP/2 Installation Instructions
1 2 3 4 7 ENTER 0 5 6 8 9 CLEAR + - LOGIC ONE EP/2 EP/2 Installation Instructions DOC. #569011000 A 7/30/04 PRINTED IN U.S.A. Regulatory Compliance Safety This device has been tested and found to be in
More informationN E W! SAI Panel Feed -Thro u g h S A I - M 1 2 / M 2 3 SA I- A New Wir ing Concep t. c o n c e p t s. c o s t s.
Data shee t SAI Panel Feed -Thro u g h S A I - M 1 2 / M 2 3 SA I- A New Wir ing Concep t SA I NPN-PNP N E W! Weidmuller is bringing innovative SAI integrator wiring solutions to help make your installation
More informationKTX REMOTE INSTALLATION INSTRUCTIONS
KTX REMOTE INSTALLATION INSTRUCTIONS SPECIAL NOTE BOONE CABLE WORKS & ELECTRONICS, INC. 1773-219TH LANE - P.O. BOX 369 READ THIS ENTIRE BOOKLET BOONE, IOWA 50036 USA BEFORE PROCEEDING WITH PHONE (515)
More informationSignet Temperature Transmitter
Loop Output Output 7 Sensr IN (RED) Sensr V (BLACK) Signet 80 Temperature 80.090 English 80.090 Rev. J 0/ English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions
More informationInstallation, Testing, and Operating Procedures 30 AMP PORTABLE AND PERMANENT SERIES GFCI SINGLE and MULTIPHASE
IMPORTANT! Please read all the information on this sheet. SAVE THESE INSTRUCTIONS! NOTICE BEFORE USING READ INSTRUCTIONS COMPLETELY. TO BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NATIONAL
More informationTCNM-ACBB1 Installation Manual
The TCNM-ACBB1 is a connection box that can be used as an accessory to facilitate system connections for installation and device replacement of several Banner family reading devices. System cabling is
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationCU-8R Installation Instructions
CU-8R Installation Instructions I. Components Model CU-8R is shipped with the following components: QTY Item 1 Stainless Steel Enclosure 2 Lexan Panels 18 Nuts 1 Wall Mount Style Phone with RJ-11 Cable
More informationSCROLL GAS PRICE DISPLAY SYSTEM ROS SERIES INSTALLATION MANUAL REV 3.0
SCROLL GAS PRICE DISPLAY SYSTEM ROS SERIES INSTALLATION MANUAL REV 3.0 Fax: (514) 683-0068 Rev : 3.0 www.novyc.com Page 1 of 11 WARNING The ROS Scroll Display System must be installed as per Novyc International's
More information* * Agilent Power Distribution Unit (PDU) Installation Guide
Agilent Power Distribution Unit (PDU) Installation Guide For use with Agilent PDU kits and PDU installation kits for Agilent instrument racks June 2008 Edition 7 E0608 *5000-0039* 5000-0039 Notice The
More informationORB TM 4-20 ma Input Box Installation & Operation Manual
IOM ORB TM 4-20 ma Input Box Installation & Operation Manual ORB TM 4-20 ma Input Box Installation & Operation Manual CONTENTS I. HANDLING & STORAGE... 1 Inspection and Handling Disposal and Recycling
More informationPOSIROT. PRAS2EX Magnetic Angle Sensor. Magnetic Angle Sensors (Dust-Ex-proof) Datasheet
Magnetic Angle Sensors (Dust-Ex-proof) Magnetic Angle Sensor Datasheet Copyright ASM GmbH Am Bleichbach 18-24 85452 Moosinning Germany The information presented in this data sheet does not form part of
More informationControl Cube T Digital Temperature Controller Operating Manual
Control Cube T Digital Temperature Controller Operating Manual Specifications Willhi WH7016+ digital thermostatic controller; 110vac; 30A relay Dual mode (heating or cooling) 13A maximum current rating
More informationModbus Header Temperature Sensor Kits: Standard Voltage Low Voltage
Technical Instruction Document Modbus Header Temperature Kits: 24444-1 Standard Voltage 24444-3 Low Voltage Disclaimer The information contained in this manual is subject to change without notice from
More informationEP-ELVCTL Elevator Control (NION-16C48M)
EP-ELVCTL Elevator Control (NION-16C48M) Product Installation Document This document covers the procedures and specifications for installing the above listed unit and when appropriate, information regarding
More informationSensors and Systems. Short Form. that protect your plant...
Sensors and Systems Short Form that protect your plant... About us What is Hansford Sensors? At Hansford Sensors, we design, develop and manufacture a wide range of high performance industrial accelerometers,
More informationUnpacking. Installation
Installation Guide Unpacking Check that the following items are in the box: - One M12 Enclosure containing one or two cameras - One or two VA100 video adapter(s) - One warranty card - One or two BNC-RCA
More informationMAXIMA+ Series Rotary Level Indicator
MAXIMA+ Series Rotary Level Indicator BinMaster: Division of Garner Industries 7201 N. 98th St., Lincoln, NE 68507 402-434-9102 email: info@binmaster.com www.binmaster.com OPERATING INSTRUCTIONS PLEASE
More informationMICRO SERIES PROCESS DISPLAYS LARGE DIGIT MODELS
The MICRO SERIES PROCESS DISPLAYS LARGE DIGIT MODELS Mighty-5 DPM MODELS Micro-P & Mighty-1 Mighty-1 Micro-P ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters and
More informationMAXIMA + Series ROTARY LEVEL CONTROL
Price $5.00 MAXIMA + Series ROTARY LEVEL CONTROL OPERATING INSTRUCTIONS PLEASE READ CAREFULLY Division of Garner Industries 7201 North 98th Street Lincoln, NE 68507-9741 (402) 434-9102 925-0268 TABLE OF
More informationAdapter Kit - Remote QSI Electronics Installation Instructions
Adapter Kit Remote QSI Electronics Installation Instructions These installation instructions cover the adapter kit installation of the QSI1, QSI2 and QSI3 versions of communications electronics. The instructions
More informationINSTALLATION INSTRUCTIONS
www.altroniccontrols.com INSTALLATION INSTRUCTIONS EXACTA 21 MONITORING AND CONTROL SYSTEM CAUTION: The EXACTA 21 CONTROL SYSTEM is CSA CERTIFIED FOR use in Class I, GROUPS C & D, Division 2 hazardous
More informationMAXIMA + Series ROTARY LEVEL CONTROL
Price $5.00 MAXIMA + Series ROTARY LEVEL CONTROL OPERATING INSTRUCTIONS PLEASE READ CAREFULLY Division of Garner Industries 7201 North 98th Street Lincoln, NE 68507-9741 (402) 434-9102 925-0268 Rev. A
More informationModel 7416LED
INSTALLATION INSTRUCTIONS FOR Model 7416LED www.sportablescoreboards.com 1 Table of Contents DESCRIPTION... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:... 3 INSTRUCTIONS FOR REPORTING SHIPPING
More informationLPG STM 94442A User s Manual
1 LPG STM 94442A User s Manual This Manual belongs to: Company: 3 Table of Contents Features....... 4 Hardware Installation...5 Monitor Mounting Dimensions.....7 Monitor Specifications...8 Sender Specifications.....9
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationPLEASE READ INSTRUCTIONS CAREFULLY BEFORE INSTALLATION!
TUC2 / TUCH2 Model Series Installation Instructions PLEASE READ INSTRUCTIONS CAREFULLY BEFORE INSTALLATION! APPLICATION The TUC2 provides temperature space monitoring with a backlit LCD. The TUCH2 provides
More informationxtablet T1600 Vehicle Holder Installation Guide
This document will step you through setting up the T1600 Vehicle Holder installation and tips for a safe, clean and long lasting installation. Preparing to Mount the Vehicle Holder Warning : Dock mounting
More informationINSTALLATION INSTRUCTIONS FOR
INSTALLATION INSTRUCTIONS FOR MODEL 3314 LED www.sportablescoreboards.com 1 Table of Contents DESCRIPTION... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:... 3 INSTRUCTIONS FOR REPORTING
More informationMA-4006, MD-4006 and MU-4006 Mounting Assemblies
Telecommunications Group Section MA4 006 002 Equipment Issue 2 Second Printing, June 2000 MA-4006, MD-4006 and MU-4006 Mounting Assemblies CONTENTS PAGE Part 1. GENERAL.............................................................................
More informationEnergy Management System. Operation and Installation Manual
Energy Management System Operation and Installation Manual AA Portable Power Corp 825 S 19 TH Street, Richmond, CA 94804 www.batteryspace.com Table of Contents 1 Introduction 3 2. Packing List 5 3. Specifications
More informationOPERATING INSTRUCTIONS 7 SERIES STATIC GENERATORS
OPERATING INSTRUCTIONS 7 SERIES STATIC GENERATORS GB Contents Page 1 Introduction 4 2 Safety 5 3 Use 6 4 Checking on Delivered Equipment 6 5 General Specification and Dimensions 7 6 Positioning 10 7 Operating
More informationDLA. DMX512 Analyzer. DLA Users Manual SV2_00 B.lwp copyright ELM Video Technology, Inc.
DLA DMX512 Analyzer DLA DLA-HH 1 Table Of Contents IMPORTANT SAFEGUARDS... 2 DLA OVERVIEW... 3 CONNECTION... 3 OPERATION... 3 HARDWARE SETUP... 4 DLA-HH (PORTABLE) LAYOUT... 4 CHASSIS LAYOUT... 4 DLA MENU
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationPhotoelectric Sensors E3F2
Photoelectric Sensors E3F2 Threaded Cylindrical Photoelectric Sensors with Built-in Amplifier for Use as an Optical Proximity Switch M18 DIN-sized cylindrical housing Housing materials: plastic, nickel
More information4 Channel DMX Driver Instruction Manual
LEDstuff.co.nz 4 Channel DMX Driver Instruction Manual Quality LED Lighting Products The LEDstuff 4 Channel DMX Driver is a flexible module that is an ideal addition to an existing home automation or lighting
More informationSPECIAL SPECIFICATION 1864 Pole Mounted Cabinet
1993 Specifications CSJ s 0924-06-221,etc. & 0924-06-223 SPECIAL SPECIFICATION 1864 Pole Mounted Cabinet 1. Description. This specification describes the minimum acceptable requirements for a weatherproof
More informationHi-Tech Transport Electronics, Inc. DUAL LEVELING VALVE PROCESSOR INSTALLATION MANUAL. For the 4600 Scale System For the 5600 Scale System
Hi-Tech Transport Electronics, Inc. DUAL LEVELING VALVE PROCESSOR INSTALLATION MANUAL For the 4600 Scale System For the 5600 Scale System September 1999 THE ACCURATE ON-BOARD ELECTRONIC SCALE For Air-Ride
More informationGSV-1A4 M12/2 M12/2. Highlights
GSV-1A4 M12/2 M12/2 Highlights Input sensitivity: 2mV/V; 4mV/V, 2 mv/v, 1mV/V, 0.5mV/V configurable via jumpers Output signals ±10V AND 12mA+-8mA on 15 pin Sub-D Integrated half and quarter bridge completion
More informationSignet Pressure Transmitter
Signet 850 Pressure English *850.090* 850.090 Rev. H /06 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents.
More informationCSI 9330 Vibration Transmitter
O-9330-070110 C 9330 Vibration Transmitter Continuously monitors critical machinery in process applications and other industrial environments Interfaces with existing alarm, control and monitoring systems
More informationMODEL 3312 LED
INSTALLATION INSTRUCTIONS FOR MODEL 3312 LED www.sportablescoreboards.com 1 Table of Contents DISCRIPTION... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:... 3 INSTRUCTIONS FOR REPORTING
More informationNEW PRODUCTS FOR FLIGHT TEST AND GVT APPLICATIONS
NEW PRODUCTS FOR FLIGHT TEST AND GVT APPLICATIONS Brian Proffitt GET CONNECTED to LEARN, SHARE, AND ADVANCE. The Dytran Story Celebrating 30+ years making world class piezoelectric sensors President Nick
More informationMODELS PD230 AND PD1230 Installation Instructions
PNEUMERCATOR Liquid Level Control Systems MODELS PD20 AND PD20 Installation Instructions Model PD20 x2 Channel Lightning Surge Protector Model PD20 x2 Channel Lightning Surge Protector COPYRIGHT 2007 PNEUMERCATOR
More informationThe Butterfly LaserMount also offers all the features you would expect from a modern butterfly laser diode fixture, including:
Page 2 202/204 Butterfly LaserMount User s Manual Introduction Thank you for choosing the Butterfly LaserMount from Arroyo Instruments. The Butterfly LaserMount is designed for high performance and long
More informationVibrating Wire Joint Meter Manual
Vibrating Wire Joint Meter Manual All efforts have been made to ensure the accuracy and completeness of the information contained in this document. RST Instruments Ltd reserves the right to change the
More informationDWYER INSTRUMENTS, INC. Series AVUL Air Velocity Transmitter. Specifications - Installation and Operating Instructions.
Series AVUL Air Velocity Transmitter Specifications - Installation and Operating Instructions Bulletin P-AVUL 3-49/64 [95.71] 2-43/64 [67.92] 1/2 NPS 3-3/16 [80.81] 1-19/32 [40.59] 31/32 24.58 3-33/64
More informationOperation Manual MODEL 2TX. 2-wire Isolated ph/orp Transmitter
Operation Manual MODEL 2TX 2-wire Isolated ph/orp Transmitter 0 2TX CONTENTS INITIAL INSPECTION.....2 INTRODUCTION......2 ASSEMBLY...3 PREPARATION....4 CONNECTING THE ELECTRODE...4 CONNECTING THE TEMPERATURE
More informationZENSOL CIRCUIT BREAKER PERFORMANCE ANALYZER
ZENSOL AUTOMATION INC. COMPUTERIZED TEST EQUIPMENT ZENSOL CIRCUIT BREAKER PERFORMANCE ANALYZER CBA-32P Micro CBA MANUAL 1W E OPERATOR S GUIDE Version 1.70 January 2001 www.zensol.com Man-1we.doc Rév 5
More informationOperating Instructions & Service Manual FOULS
FOULS Operating Instructions & Service Manual FOULS Basketball Player Fouls Panels Model MP-5215 EFFECTIVE S.N. 17,100, June 18, 2001 TABLE OF CONTENTS PAGE 1. GENERAL INFORMATION 3 1.1 DESCRIPTION 1.2
More informationOZONE SWITCH Model OS-6. OS-6 Features
USER MANUAL OZONE SWITCH Model OS-6 OS-6 Features The OS-6 is an industrial grade ozone controller and monitor. The OS-6 design is optimized for accuracy and ease of installation, setup and operation.
More informationEVERSAN. Instruction Manual MODEL 9007/9008 TENNIS SCOREBOARD. Address: 34 Main Street, Whitesboro, NY 13492
MODEL 9007/9008 TENNIS SCOREBOARD Instruction Manual Address: 34 Main Street, Whitesboro, NY 13492 Phone: 315-736-3967 Toll Free: 800-383-6060 Fax: 315-736-4058 SCOREBOARDS TIMERS MESSAGE SIGNS VIDEO DISPLAYS
More informationModel: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features
Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Fully Adjustable, Multiple Viewing Angle Smart Camera. High Resolution, 1/2 CMOS Color Camera
More informationFE8171V. 3MP 360 Panoramic View Vandal-proof
FE8171V 3MP 360 Panoramic View Vandal-proof Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating
More informationand Network Interface Modules Installation Instructions
4010-9817 and 4010-9821 Network Interface Modules Installation Instructions Cautions and Warnings DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the
More informationE3S-A. Built-in Amplifier Photoelectric Sensor (Medium Size) Ordering Information. Built-in Amplifier Photoelectric Sensors. Horizontal. 7 m.
Built-in Amplifier (Medium Size) ES-A CSM_ES-A_DS_E Be sure to read Safety Precautions on page 0. Ordering Information Built-in Amplifier s Red light Infrared light Sensing method Appearance Connection
More informationNPN output PNP output Cord connection Cord length: 2 m Through-beam 7 m Light-ON. 2 m. (selectable by wiring) Diffuse reflective 0.
Built-in Amplifier Photoelectric Sensor E3V3 Easy-to-use, Low-cost Photoelectric Sensor Incorporating s that can be clearly seen from a distance. A series of models with an M8 metal junction connector
More informationQuick Draw Electronics. Shooting Sports Timer User Manual. Model AIO-1
Quick Draw Electronics Shooting Sports Timer User Manual Model AIO-1 Rev. C October 2017 QUICKDRAW ELECTRONICS SHOOTING SPORT TIMER SYSTEM THE SYSTEM CONSISTS OF; 1 IMPACT SENSOR 1 LIGHT ASSEMBLY 1 ALL
More informationSERVICE MANUAL MODEL WPP-331-D WEATHERPROOF TELEPHONE MODEL HOB-331-D WEATHER RESISTANT TELEPHONE. and MODEL SSP-311-D STAINLESS STEEL PANEL TELEPHONE
WPP(HOB)-331-D or SSP-311-D ATD-11 Issue 5.00 SERVICE MANUAL FOR MODEL WPP-331-D WEATHERPROOF TELEPHONE MODEL HOB-331-D WEATHER RESISTANT TELEPHONE and MODEL SSP-311-D STAINLESS STEEL PANEL TELEPHONE EQUIPPED
More informationNeets Control QueBec P/N#: P/N#: User Manual
Neets Control QueBec P/N#: 310-0011 P/N#: 310-0012 User Manual Foreword The purpose of this document is to describe how to install and configure the Neets Control QueBec II and Neets Control QueBec III.
More informationBTU-4D/BTU-4D-I Digital Temperature Unit & Sensors. Installation and Operation Manual
BTU-4D/BTU-4D-I Digital Temperature Unit & Sensors Installation and Operation Manual BTU-4D/BTU-4D-I Installation and Operation Manual Rev E Table of Contents Introduction... 1 TEMP OUTDOOR Sensor... 1
More informationCONTROL MICROSYSTEMS Thermocouple Analog Input Module. Hardware Manual
550 Thermocouple Analog Input Hardware Manual CONTROL MICROSYSTEMS SCADA products... for the distance Steacie Drive Telephone: 63-59-93 Kanata, Ontario Facsimile: 63-59-0 KK A9 Technical Support: -6-676
More informationModel XAV2 & XAV2-LED System Installation
Model XAV2 & XAV2-LED System Installation 10/09/07 This document provides instructions for installing the Polara Push Button Station (PBS) and the XAVCU2 or XAVCU2-DC Control Unit. Mounting the Push Button
More informationGASGUARDIAN RD3 Remote Display OPERATING & INSTALLATION MANUAL
GASGUARDIAN RD3 OPERATING & INSTALLATION MANUAL 3GasGuardian RD Operating and Instruction Manual Table of Contents General description... 4 Installation... 4 Locating the GasGuardian RD1... 4 Installation
More informationLN3X Series Motor and Drives
LN3X Series Motor and Drives Operator's Manual PN 04-01920 C PRECISION MOTION CONTROLS 2175 De La Cruz Blvd., #1 Santa Clara, CA 95050 1 Contents INTRODUCTION... 3 Description... 3 Features... 3 Warranty...
More informationDatastick Portable Data Collectors
CTC Compatible Products for Datastick Portable Data Collectors A CTC Web Based Training Seminar General Purpose Accelerometers 100 mv/g Mini-MIL Connectors AC192 Series AC194 Series AC140 Series AC144
More informationMounting DIGITAL DISPLAY
Mounting The Class digital display mounts in a. by. cutout. Overall area necessary for installation is. by.. Two 0.0 diameter holes are provided for mounting screws..0".0..0.900 Ø 0.0" () HOLES."." DIGITAL
More informationBack Mount SIP Access Control Intercom Installer s Guide
Back Mount SIP Access Control Intercom Installer s Guide This step-by-step guide will help you install your Wahsega Labs back mount SIP access control intercom. What s in the Box www.wahsega.com Page 2
More informationPDI Modular Compact Remote Power Panel
Guide Specifications (Revision 000, 6/17/2016) 1 GENERAL 1.1 Summary These specifications describe requirements for a remote power panel (RPP) distributing power to sensitive loads. These specifications
More informationDocking station. Technical Documentation
Docking station Technical Documentation Version 1.1 Release date: 01.09.2015 Table of contents 1 Introduction...3 2 Layout and dimensions...4 3 What s included in the box...4 4 Connecting devices...5 4.1
More information