A block diagram of the HXFP-2C21XX XFP optical transceiver is shown below
|
|
- Calvin Copeland
- 5 years ago
- Views:
Transcription
1 Features Support 9.95 Gb/s to 10.5 Gb/s CWDM-SH application Uncooled 16-Wavelength CWDM DFB LD: 1270nm to 1610nm Up to 10Km Units Available over single mode fiber +3.3V Single power supply XFI electrical interface and Hot pluggable XFP MSA package with duplex LC connector 2-wire interface for integrated Digital Diagnostic monitoring Excellent EMI performance High reliability Low power consumption less than 1.5 W Operating case temperature: -5~+70 C Applications 10GBASE-LR/LW 10Gigabit Ethernet SONET OC-192 IR-2&SDH STM S-64.2b Other optical links Standard Compatible with XFP MSA Compatible with IEC Class 1 laser eye safe FDA 21 CFR and , class 1 RoHS 6 compliance Description HXFP-2C21XX is a high performance, cost effective and optimized for use in a specification single channel CWDM XFP MSA optical transceiver, This device RoHS compliant is a full duplex serial electric, serial optical device with both transmit and receive functions contained in a single module. It is designed for support data rates from 9.95Gbps to 10.5Gbs and transmission distance to 10 km on 9/125 μm SMF The transceiver consists of two sections: The transmitter section incorporates an uncooled CWDM DFB laser, driver, The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and CDR. A block diagram of the HXFP-2C21XX XFP optical transceiver is shown below Page 1 of 9
2 The module is hot pluggable into the 30-pin XFI connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module. The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. The user can access transceiver monitoring and configuration data via the 2-wire XFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area. Absolute Maximum Ratings Parameter Symbol Min. Max. Unit Storage Temperature T S C Supply Voltage VCC V Case Operating Temperature Top Power Dissipation PD W Recommended Operating Environment Supply Voltage VCC V Power Supply Current ICC ma Data Rate T OP Gbps Notes: 1. VCC2,VCC5 not required for this design. Optical Characteristics Transmitter Section Output Center Wavelength λ C See wavelength table nm Spectral Width (-20dB from Peak ) FW nm Average Optical Output Power Po dbm Extinction Ratio Er db Side Mode Suppression Ratio SMSR 30 db Transmitter and Dispersion Penalty TDP 3.2 db Average Launch power of OFF P OFF -30 dbm Tx Jitter Per 802.3ae requirements Relative Intensity Noise RIN -130 db/hz 0 C Receiver Section Page 2 of 9
3 Output Center Wavelength λ C nm Receiver Sensitivity,PIN SEN dbm Receiver Reflectance R rx -12 db Receiver Overload POL +0.5 dbm LOS Assert LOSA -32 dbm LOS Deassert LOSD -18 dbm LOS Hysteresis LOSH 0.5 db Wavelength Table Part Number Min Typical Max HXFP-2C ClaspColor Code Light Purple Part Number Min Typical Max ClaspColor Code HXFP-2C Gray HXFP-2C Sky Blue HXFP-2C Violet HXFP-2C Yellow Green HXFP-2C Blue HXFP-2C Yellow Ocher HXFP-2C Green HXFP-2C Pink HXFP-2C Yellow HXFP-2C Silver HXFP-2C Orange HXFP-2C Black HXFP-2C Red HXFP-2C Yellow Orange HXFP-2C Orange CWDM: 16 Wavelengths from 1270 nm to 1610 nm, each step 20 nm. Electrical Characteristics Transmitter Section Input differential impedance Rin 100 Ω 1 Differential data input swing Vin,pp mv Transmit Disable Voltage VD 2.0 Vcc V 2 Transmit Enable Voltage VEN GND GND+0. V Transmit Disable Assert Time 8 10 us Receiver Section Differential data output swing Vout,pp mv 3 Data output rise time tr 38 ps 4 Data output fall time tf 38 ps 4 Page 3 of 9
4 LOS Fault VLOS fault Vcc VccHOS V 5 LOS Normal VLOS norm 05 GND GND+0 T V 5 Power Supply Rejection PSR 5 6 Notes: 1. After internal AC coupling. 2. Or open circuit. 3. Into 100 ohms differential termination % 5. Loss Of Signal is open collector to be pulled up with a 4.7k 10kohm resistor to V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 6. Per Section in the XFP MSA Specification. 2-wire Serial Digital Diagnostic Memory Map Management Interface Figure 1. Digital Diagnostic Memory Map The structure of the memory map is shown in Figure 1, which is accessible over a 2 wire erial interface at the 8-bit address X (A0h). The normal 256 Byte I2C address space is divided into lower and upper blocks of 128 Bytes. The lower block of 128 Bytes is always directly available and is used for the diagnostics and control function. The monitoring specification is shown in Table 6. Multiple blocks of Page 4 of 9
5 memories are available in the upper 128 Bytes of the address space. These are individually addressed through a table select Byte which the user enters into a location in the lower address space. Thus, there is a total available address space of 128 * 256 = 32Kbytes in this upper memory space. The contents of Table 01h are list in table 7 below. PLS refer INF-8077i (Revision 4.0) for detailed information Digital Diagnostic Monitor Characteristics Parameter Symbol Min. Max Unit Temperature monitor absolute error DMI_Temp degc Laser power monitor absolute error DMI_TX db RX power monitor absolute error DMI_RX db Supply voltage monitor absolute error DMI_VCC V Bias current monitor DMI_Ibias -10% 10% ma Pin Function Definitions Pin Logic Symbol Name/Description Ref. Page 5 of 9
6 Pin Logic Symbol Name/Description Ref. 1 GND Module Ground 1 2 VEE5 Optional 5.2 Power Supply Not required 3 LVTTL-I Mod-Desel Module De-select; When held low allows the module to, respond to 2-wire serial interface commands 4 LVTTL-O Interrupt Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface 2 5 LVTTL-I TX_DIS Transmitter Disable; Transmitter laser source turned off 6 VCC5 +5 Power Supply Not required 7 GND Module Ground 1 8 VCC3 +3.3V Power Supply 9 VCC3 +3.3V Power Supply 10 LVTTL-I SCL Serial 2-wire interface clock 2 11 LVTTL- SDA Serial 2-wire interface data line 2 12 I/O Module Absent; Indicates module is not present. Grounded in the LVTTL-O Mod_Abs module LVTTL-O Mod_NR Module Not Ready; 2 14 LVTTL-O RX_LOS Receiver Loss of Signal indicator 2 15 GND Module Ground 1 16 GND Module Ground 1 17 CML-O RD- Receiver inverted data output 18 CML-O RD+ Receiver non-inverted data output 19 GND Module Ground 1 20 VCC2 +1.8V Power Supply Not required 21 LVTTL-I P_Down/RST Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of themodule including the 2-wire serial interface, equivalent to a power cycle. 22 VCC2 +1.8V Power Supply Not required 23 GND Module Ground 1 24 PECL-I RefCLK+ Reference Clock non-inverted input, AC coupled on the host board Not required 3 25 PECL-I RefCLK- Reference Clock inverted input, AC coupled on the host board Not required 3 26 GND Module Ground 1 27 GND Module Ground 1 28 CML-I TD- Transmitter inverted data input 29 CML-I TD+ Transmitter non-inverted data input Page 6 of 9
7 Pin Logic Symbol Name/Description Ref. 30 GND Module Ground 1 Note: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k 10k ohms on host board to a voltage between 3.15Vand 3.6V. 3. A Reference Clock input is not required. Mechanical Design Diagram XFP transceivers are compliant with the dimensions defined by the XFP Multi-Sourcing Agreement (MSA). Application Schematics Recommended Host Board Power Supply Circuit Page 7 of 9
8 The recommended interface circuit Page 8 of 9
9 Ordering information HXFP Transmission Distance 0:Ultra Long Reach 1:Long Reach 2:Intermediate 3:Short Reach Wavelength 3: 1310nm 5: 1550nm 8: 850nm C: CWDM D: DWDM LD Type 1: FP-LD/ PIN-TIA 2: DFB-LD / PIN-TIA 3: VCSEL/ PIN-TIA 4: EML / PIN-TIA 5: EML / APD Costomer Specific Code Channel Code 01~08: CWDM 1310 range (1270nm~1450nm) 09~16: CWDM 1550 range (1470nm~1610nm) 17~61: DWDM 1310 range (191.7~196.1THz) ( nm~ nm) Operation Temperature 1:0 ~ +70 C 2:-10 ~ +85 C 3:-40 ~ +85 C Page 9 of 9
A block diagram of the HXFP-XDX1XX XFP optical transceiver is shown below
Features Support 9.95 Gb/s to 11.3 Gb/s serial optical and electrical interface Temperature Stabilized DWDM EML Transmitter 1550nm cooled EML transmitter with TEC and PIN receiver Both 40Km and 80Km Units
More informationBC D 10 Gb/s 10km XFP Optical Transceiver
BC-1396-10D 10 Gb/s 10km XFP Optical Transceiver PRODUCT FEATURES Hot-pluggable XFP footprint Supports 9.95Gb/s to 11.3Gb/s bit rates XFI Loopback Mode RoHS-6 Compliant (lead-free) Power dissipation
More informationData Sheet. 10Gb/s Hot Pluggable XFP Transceiver, 1310nm, DFB-LD, Duplex LC, Single Mode, 10 km. PXFP-2321SF Issue: January 2009
Features: Supports 9.95Gb/s to 10.5Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 10km Uncooled 1310nm DFB laser. Duplex LC connector Power dissipation
More informationSHXP-10G-LR. 10Gb/s XFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1310nm DFB/PIN, Single mode, 10km, 0~70 C /-40~ +85 C
SHXP-10G-LR 10Gb/s XFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1310nm DFB/PIN, Single mode, 10km, 0~70 C /-40~ +85 C SHXP-10G-LR inter-converting the 10Gb/s serial electrical data stream with the
More informationSHXP-10G-Dxx-80. Central Wavelength Frequency (THZ)
SHXP-10G-Dxx-80 10Gb/s DWDM XFP Transceiver Hot Pluggable, Duplex LC, +3.3V & +5V, 100GHz ITU Grid C Band, EML/APD Single mode, 80km, 0~70 C /-40~ +85 C SHXP-10G-Dxx-80 10Gb/s DWDM XFP transceiver, inter-converting
More informationParameter Symbol Min Max Unit
Features: Supports 9.95Gb/s to 11.3Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 20km 1310nm DFB laser transmitter. Duplex LC connector Power dissipation
More informationGB-XFP-D50-XX-40S 10Gb/s 40km DWDM XFP Optical Transceiver
GB-XFP-D50-XX-40S 10Gb/s 40km DWDM XFP Optical Transceiver PRODUCT FEATURES Hot-pluggable XFP footprint Supports 9.95Gb/s to 11.3Gb/s bit rates Supports Lineside and XFI loopback RoHS-6 Compliant (lead-free)
More informationXFP 10GLR OC192SR. 10Gbps XFP Optical Transceiver, 10km Reach
XFP 10GLR OC192SR 10Gbps XFP Optical Transceiver, 10km Reach Features Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 10km with SMF 1310nm Uncooled EML laser
More information10G-XFP-LR (10G BASE-LR XFP) Datasheet
10G-XFP-LR (10G BASE-LR XFP) Datasheet Features Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 10km with SMF 1310nm uncooled DFB laser XFP MSA package with duplex
More informationSHXP-10G-B60. 10Gb/s BiDi XFP Transceiver Hot Pluggable, Simplex LC, +3.3V, 1270/1330nm DFB/APD, 60km, 0~70 C /-40~ +85 C
SHXP-10G-B60 10Gb/s BiDi XFP Transceiver Hot Pluggable, Simplex LC, +3.3V, 1270/1330nm DFB/APD, 60km, 0~70 C /-40~ +85 C SHXP-10G-B60 10Gb/s BiDi optical transceiver, inter-converting the 10Gb/s serial
More information10Gbps XFP Transceiver
XFP-10G-L-OC192-SR1-EO 10Gbps XFP Transceiver Features Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 10km Uncooled 1310nm EML/DFB laser Duplex LC connector
More informationEOLX X series 10G XFP Transceiver
EOLX-1596-40X series 10G XFP Transceiver Features Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 40km Temperature-stabilized DWDM rated EML transmitter Duplex
More informationKRN-XF-SMM0310GD. 10Gb/s 300m XFP Transceiver Hot Pluggable, Duplex LC, 850nm, VCSEL, Multi mode
Product Datasheet KRN-XF-SMM0310GD 10Gb/s 300m XFP Transceiver Hot Pluggable, Duplex LC, 850nm, VCSEL, Multi mode Features Support multi protocol from 9.95Gb/s to 11.3Gb/s Hot pluggable 30 pin connector
More informationTS-XF-DXX10-80D 10Gb/s 80km DWDM XFP Optical Transceiver
TS-XF-DXX10-80D 10Gb/s 80km DWDM XFP Optical Transceiver PRODUCT FEATURES Hot-pluggable XFP footprint Supports 9.95Gb/s to 11.3Gb/s bit rates Supports Lineside and XFI loopback RoHS-6 Compliant (lead-free)
More informationFeatures: Compliance: Applications: Warranty: XFP-10GZR-OC192LR-GT Multirate XFP 10GBASE-ZR & OC-192/STM-64 LR2 Cisco Compatible
The GigaTech Products is programmed to be fully compatible and functional with all intended CISCO switching devices. This XFP optical transceiver is designed for IEEE 802.3ae 10GBASE-ZR, 10GBASE-ZW, 10GFC
More informationGP-XFP-1L-LEG. 10Gbs XFP Transceiver
Part# 39716 GP-XFP-1L-LEG CISCO COMPATIBLE 10GBASE-LR XFP SMF 1550NM 10KM REACH LC DOM GP-XFP-1L-LEG 10Gbs XFP Transceiver Features Duplex LC connector Support hot-pluggable Metal with lower EMI Excellent
More information10Gpbs 10km Range 1310nm XFP Optical Transceiver
Page 1 of 7 Overview ARIA s 10Gbps 10km Range 1310nm XFP Optical Transceiver is compliant with the 10G Small Form-Factor Pluggable (XFP) Multi-Source Agreement (MSA) supporting data-rates of 10.3125 Gbps
More informationProduct Specification. 10Gb/s 10km Datacom XFP Optical Transceiver FTRX-1411D3
Product Specification 10Gb/s 10km Datacom XFP Optical Transceiver FTRX-1411D3 PRODUCT FEATURES Supports 9.95Gb/s to 10.5Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 10km Uncooled 1310nm
More information81.X111GSR1131S-TP 10Gb/s 850nm Multimode XFP Optical Transceiver
81.X111GSR1131S-TP 10Gb/s 850nm Multimode XFP Optical Transceiver PRODUCT FEATURES Hot-pluggable XFP footprint Supports 9.95Gb/s to 11.3Gb/s bit rates XFI Loopback Mode Power dissipation
More informationA APXDxxHM0xDL Gb/s XFP Transceiver. APXDxxHM0xDL40. Product Features. Applications. General. Product Selection. Product Channel Selection
10.3Gb/s XFP Transceiver APXDxxHM0xDL40 Product Features Supports 9.95 to 11.3Gb/s Duplex LC connector Hot-pluggable XFP footprint Cooled 1550nm EML laser RoHS compliant and Lead Free 40Km link length
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION P/N AC-XF-3G10-10 Description 10Gb/s 1310nm XFP 10km Optical Transceiver Version A0 Issue Date 2015.06.07 Prepared By Checked By Approved By Jason Qi Wenshan Yang Nan Wang AC-XF-3G10-10
More information10G-XFP-ER (10G BASE-ER XFP) Datasheet
10G-XFP-ER (10G BASE-ER XFP) Datasheet Features Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 10km with SMF 1310nm uncooled DFB laser XFP MSA package with duplex
More informationXFP Bi-Directional 10G 80km Tx1490/Rx1550nm & Tx1550/Rx1490nm SLXFB-XXXX-80
XFP Bi-Directional 10G 80km Tx1490/Rx1550nm & Tx1550/Rx1490nm SLXFB-XXXX-80 Description Sourcelight SLXFB-XXXX-80 is XFP BIDI 80KM transceivers are designed for 10G Ethernet 10G BASE-LR/LW per 802.3ae
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION P/N Description 10Gbps CWDM XFP 40km Transceiver Version A0 Issue Date 2015.06.07 Prepared By Checked By Approved By Jason Qi Wenshan Yang Nan Wang 10Gbps CWDM 40km XFP Transceiver
More informationOPTOSTAR's OP-MDCX8xxL1SD-40 10G Cooled EML XFP DWDM transceivers are designed for 10G
10Gbps 40km XFP DWDM Optical Transceiver Product Features Duplex LC Connector Support hot-pluggable Metal with lower EMI Excellent ESD protection XFP MSA compliant RoHS Compliant and Lead-Free Compliant
More informationAPPROVAL SHEET. 10Gbps XFP Transceiver, 80km Reach X55-64D80-RLP R&D QA CEO
APPROVAL SHEET Project Name Product Name Model Name 10Gbps XFP Transceiver, 80km Reach X55-64D80-RLP Approval Code Reporting Date 2015-05-11 Approval Date Customer Maker R&D QA CEO Maker : FOTTU CO., LTD
More informationProduto: 10Gbps XFP Transceiver, Single Mode, 40km Reach Modelo: V7-XFP-ER31 Documentação: Técnica/Datasheet. Features
Produto: 10Gbps XFP Transceiver, Single Mode, 40km Reach Modelo: V7-XFP-ER31 Documentação: Técnica/Datasheet Features Supports 8.0Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint, Built-in digital
More informationFeatures. Description. Standard. Applications. RoHS Compliant 10Gb/s DWDM 80KM Multi-rate XFP Optical Transceivers OPXPDxx1X3CDL80
RoHS Compliant 10Gb/s DWDM 80KM Multi-rate XFP Optical Transceivers OPXPDxx1X3CDL80 Features Hot pluggable Support 9.95Gb/s to 11.1Gb/s bit rates Below 3.5W power dissipation XFP MSA package with duplex
More informationXFP Series. Part No. Data Rate Laser Fiber Type Distance Temp.
EOLX-1396-20 1310nm XFP single-mode for 10GbE/10GFC/SDH/SONET Duplex XFP Transceiver RoHS6 Compliant XFP Series Features Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link
More informationXFP Series EOLX X. Features. Applications. Ordering Information
EOLX-1596-80-X 1550nm XFP Single-Mode for 10GbE/FC/SDH/SONET Duplex XFP Transceiver RoHS6 Compliant XFP Series Features Supports 9.95Gb/s to 11.3Gb/s Bit Rates Hot-pluggable XFP Footprint Maximum Link
More informationPart Number Operating temperature DDMI. APCS43123CDL20 Commercial Yes. APCS43123IDL20 Industrial Yes
APCS43123xxL20 Product Features Two Bi-Directional transceivers in one SFP package Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1490nm DFB laser transmitter RoHS compliant
More information25Gb/s 10km SFP28 Optical Transceiver TR-PY13L-N00 Product Specification
25Gb/s 10km SFP28 Optical Transceiver TR-PY13L-N00 Product Specification Features Up to 25.78Gb/s bi-directional data links 1310nm DFB transmitter, PIN photodetector 2-wire interface for management specifications
More informationSHFP-2G-B Gb/s BiDi SFP Transceiver Hot Pluggable, Simplex LC/SC, +3.3V, Single mode, 20km, 0~70 C 1310/1550nm or 1310/1490nm DFB/PIN
SHFP-2G-B20 2.5Gb/s BiDi SFP Transceiver Hot Pluggable, Simplex LC/SC, +3.3V, Single mode, 20km, 0~70 C 1310/1550nm or 1310/1490nm DFB/PIN SHFP-2G-B20 high performance, cost-effective 2.5G BiDi SFP transceiver
More informationProduct Specification. 10Gbps 2KM XFP Transceiver PLXFP1310GLR02
Product Specification 10Gbps 2KM XFP Transceiver PLXFP1310GLR02 Product Features 9.95Gbps to 11.1Gbps data links 2km with 9/125µm SMF V20140818 1310nm FP laser Duplex LC Connector Hot-pluggable XFP footprint
More informationXFP Series. EOLX XX Series. Features. Applications. Ordering Information
EOLX-1696-23XX Series XFP DWDM Single-Mode for 10GbE/10GFC/SDH/SONET Duplex XFP Transceiver RoHS6 Compliant XFP Series Features Available in all C-Band Wavelength on the 100GHz ITU-T Grid Supports 9.95Gb/s
More informationParameter Symbol Min. Typical Max. Unit Storage Temperature T S C Supply Voltage V CC T, R V Relative Humidity RH 0 85 %
Features: Supports 8.5Gb/s to 11.3Gb/s bit rates Hot-pluggable SFP+ footprint Single LC for Bi-directional Transmission Maximum link length of 40km Built-in 1270 WDM Uncooled 1270nm DFB Laser. Power dissipation
More information10Gbps SFP + 2core (10km)
10Gbps SFP + 2core (10km) P31-64D10-RLP Features Hot-pluggable SFP+ footprint Supports 9.95Gbps to 10.5Gbps 10km transmission distance Uncooled 1310nm DFB Laser InGaAs PIN-TIA PD receiver Compliant with
More informationSHFP-GE-EX. 1.25Gb/s SFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1550nm DFB/PIN, Single mode, 40km, 0~70 C
SHFP-GE-EX 1.25Gb/s SFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1550nm DFB/PIN, Single mode, 40km, 0~70 C SHFP-GE-EX high performance, cost effective transceiver complies with the Small Form Factor
More informationXFP 10G Transceiver M10GB-XFP-BIDI40
XFP 10G Transceiver M10GB-XFP-BIDI40 Features: Supports 9.95Gb/s to 11.3Gb/s bit rates Hot-pluggable XFP footprint Single LC for Bi-directional Transmission Maximum link length of 40km Built-in 1270/1330
More informationTUNABLE XFP DWDM 10G 80Km ZR SLXFD-10GE-ZR-T
TUNABLE XFP DWDM 10G 80Km ZR SLXFD-10GE-ZR-T The transceiver module is fully compliant with the XFP MSA standard and can be hot-plugged into the 30-pin XFP connector on the host board. By limiting inrush
More informationSpecification. Small Form Factor Pluggable Dual Transmitter (Non-MSA) LC Receptacle SFP+ 12 Gigabit SDI TIN-A1C61-F14
Specification Small Form Factor Pluggable Dual Transmitter (Non-MSA) LC Receptacle SFP+ 12 Gigabit SDI TIN-A1C61-F14 Model Name Description Voltage Category Device type Interface LOS Temperature Latch
More informationPower budget. Laser. EOLX XXX 10Gbps EML EA 14dB Standard LC. EOLX XXXE 10Gbps EML EA 14dB Extended LC
EOLX-1696-14XXX series XFP Single-Mode for 10GbE/10GFC/SDH/SONET Duplex DWDM XFP Transceiver RoHS6 Compliant XFP Series Features Supports 9.95Gb/s to 11.1Gb/s bit Rates Hot-Pluggable XFP Footprint 14dB
More information10G SFP + Bi-di Transceiver Hot Pluggable, single LC, 1270nm/1330nm, DFB LD, Single Mode, 20km PSFP F/PSFP F
DATASHEET DESCRIPTION: PeakOptical Bi-directional PSFP10-2733/PSFP10-3327 10Gb/s (SFP+) transceivers are compliant with the current SFP+ Multi- Source Agreement (MSA) Specification. They comply with 10GBASE-LR/LW
More information10G Multi-Rate 10km Datacom SFP+ Transceiver TR-PX13L-NRS
10G Multi-Rate 10km Datacom SFP+ Transceiver TR-PX13L-NRS Features 10Gb/s serial optical interface compliant to 802.3ae 10GBASE-LR FC 2G/4G/8G compatible, hardware/software rate select function implemented
More informationXFP Series EOLX X. Features. Applications. Ordering Information
EOLX-1596-80-X 1550nm XFP Single-Mode for 10GbE/FC/SDH/SONET Duplex XFP Transceiver RoHS6 Compliant Features Supports 9.95Gb/s to 11.3Gb/s Bit Rates Hot-pluggable XFP Footprint Maximum Link Length up to
More informationSHPP-10G-LR. 10Gb/s SFP+ Transceiver Hot Pluggable, Duplex LC, +3.3V, 1310nm DFB/PIN, Single mode, 10km
SHPP-10G-LR 10Gb/s SFP+ Transceiver Hot Pluggable, Duplex LC, +3.3V, 1310nm DFB/PIN, Single mode, 10km SHPP-10G-LR is a very compact 10Gb/s optical transceiver module for serial optical communication applications
More informationGLC-FE-100FX-RGD-LEG. 155Mbps SFP Transceiver
39491 GLC-FE-100FX-RGD-LEG CISCO 100BASE-FX SFP MMF 1310NM 2KM REACH LC RGD GLC-FE-100FX-RGD-LEG 155Mbps SFP Transceiver Features Operating Data Rate up to 155Mbps 1310 FP Laser transmitter 2km with 50/125
More informationT A S A 1 E H
Specification Small Form Factor Pluggable Duplex LC Receptacle SFP28 Optical Transceivers Module 25GBASE-SR, CT Ordering Information T A S A 1 E H 1 8 3 4 Model Name Voltage Category Device type Interface
More informationGPP-316G-LRX 1310 nm 6.25Gbps SFP+ Transceiver 10km for CPRI and OBSAI
GPP-316G-LRX 1310 nm 6.25Gbps SFP+ Transceiver 10km for CPRI and OBSAI Features Support Multi Rate up to 6.25 Gbps CPRI/OBSAI Compatible Optical Interface Hot Pluggable SFP+ footprint 1310nm DFB transmitter,
More informationXFCxx070100D XFP CWDM Dual Fibre Transceiver ITU CWDM / 70km / 10 Gigabit Ethernet
XFCxx070100D XFP CWDM Dual Fibre Transceiver ITU CWDM / 70km / 10 Gigabit Ethernet For your product safety, please read the following information carefully before any manipulation of the transceiver: ESD
More information10Gb/s SFP+, Hot Pluggable, Duplex LC, +3.3V, 1550nm, Single Mode, 80km, EML & APD Optical Transceiver PSFP SF
DATASHEET DESCRIPTION: PeakOptical's is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s. The module converts a 10Gb/s serial electrical data stream
More information10Gb/s XFP Optical Transceiver Module
10Gb/s XFP Optical Transceiver Module 10GBASE-SR/SW Features 10Gb/s serial optical interface compliant to 80.3ae 850nm VCSEL transmitter and Pin photodiode receiver XFP Mechanical interface with bail latch
More informationSFP+ ER DWDM Optical Transceiver Module AO+-DXX-R40 10GBASE-ER/EW, up to 40km SMF Transmission
SFP+ ER DWDM Optical Transceiver Module AO+-DXX-R40 10GBASE-ER/EW, up to 40km SMF Transmission Features 10Gb/s serial optical interface compliant to 802.3ae 10GBASE-ER/EW Electrical interface compliant
More informationFOBP3151L10C 1.25Gbps SFP Transceiver, Single Mode, 10km Reach 1310nm TX / 1550nm RX
FOBP3151L10C 1.25Gbps SFP Transceiver, Single Mode, 10km Reach 1310nm TX / 1550nm RX Product Features Supports up to 1.25Gbps bit rates Hot-pluggable SFP footprint 1310nm FP laser and PIN photo detector,
More informationT A S X 1 U S 1 K 1 1
Specification Small Form Factor Pluggable Duplex LC Receptacle XFP Optical Transceivers OC-192 / STM-64 / 10 Gigabit Ethernet Ordering Information T A S X 1 U S 1 K 1 1 Model Name Voltage Category Device
More informationSHFP-GE-B Gb/s BiDi SFP Transceiver Hot Pluggable, Simplex LC/SC, +3.3V, Single mode, 80km, 0~70 C 1490/1550nm DFB/PIN
SHFP-GE-B80 1.25Gb/s BiDi SFP Transceiver Hot Pluggable, Simplex LC/SC, +3.3V, Single mode, 80km, 0~70 C 1490/1550nm DFB/PIN SHFP-GE-B80 high performance, cost-effective 1.25G BiDi SFP transceiver complies
More informationFeatures: Applications: Description: Product Datasheet
KRN-SF-(X)SM020G - 1.25Gb/s 20Km SFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1310nm, FP-LD, Single-mode KRN-SF-(X)SM020GD - 1.25Gb/s 20Km SFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1310nm, FP-LD,
More informationFSP-CWDM Gb/s 80km CWDM SFP+ Transceiver Hot Pluggable, Duplex LC, +3.3V, 1470~1610nm, CWDM EML&APD, Single mode
FSP-CWDM-80 10Gb/s 80km CWDM SFP+ Transceiver Hot Pluggable, Duplex LC, +3.3V, 1470~1610nm, CWDM EML&APD, Single mode Features: ² Supports 9.95 to 11.3Gb/s bit rates ² Hot-Pluggable ² Duplex LC connector
More information10Gb/s XFP Optical Transceiver. Module 1310nm 10km LR
10Gb/s XFP Optical Transceiver Module 1310nm 10km LR Features 10Gb/s serial optical interface compliant to 80.3ae Uncooled 1310nm DFB transmitter and Pin photodiode receiver XFP Mechanical interface with
More informationSO-QSFP-LR4-20. QSFP, 40GBase-LR, CWDM, SM, DDM, 10dB, 20km OVERVIEW PRODUCT FEATURES APPLICATIONS ORDERING INFORMATION DATASHEET 4.
SO-QSFP-LR4-20 QSFP, 40GBase-LR, CWDM, SM, DDM, 10dB, 20km OVERVIEW The SO-QSFP-LR4-20 is a transceiver module designed for 20km optical communication applications. The design is compliant to 40GBASE-LR4
More information10Gb/s SFP+ SDH/SONET Optical Transceiver Module TR-PX13L-NSN
10Gb/s SFP+ SDH/SONET Optical Transceiver Module TR-PX13L-NSN Features 10Gb/s serial optical interface compliant to SONET OC192/SDH STM64 and 802.3ae Hardware/Software Rate select function for 8.5G and
More informationGPP-316G-LRX 1310 nm 6.25Gbps SFP+ Transceiver 10km for CPRI and OBSAI
GPP-316G-LRX 1310 nm 6.25Gbps SFP+ Transceiver 10km for CPRI and OBSAI Features Support Multi Rate up to 6.25 Gbps CPRI/OBSAI Compatible Optical Interface Hot Pluggable SFP+ footprint 1310nm DFB transmitter,
More informationSFP+ ZR DWDM Optical Transceiver Module TR-GXxxZ-N00 10GBASE-ZR/ZW, up to 80km SMF Transmission. (Preliminary) Figure1: Application in System
SFP+ ZR DWDM Optical Transceiver Module TR-GXxxZ-N00 10GBASE-ZR/ZW, up to 80km SMF Transmission (Preliminary) Features 10Gb/s serial optical interface compliant to 802.3ae 10GBASE-ZR/ZW Electrical interface
More information40 Gigabit QSFP CWDM 1310 nm LR4 for 10 km
Features 4 CWDM lanes MUX/DEMUX design Up to 11.2Gbps data rate per wavelength QSFP MSA compliant Up to 10km transmission Operating case temperature: 0~70C Maximum 3.5W operation power RoHS compliant Applications
More information3C-LINK 100GBASE-LR4 QSFP28 Optical Transceiver Module P/N: 3C-QSFP28-LR4
Features 3C-LINK 100GBASE-LR4 QSFP28 Optical Transceiver Module P/N: 3C-QSFP28-LR4 4 channels full-duplex transceiver modules Transmission data rate up to 26Gbps per channel 4 x 26Gb/s DFB-based LAN-WDM
More information10Gb/s Multirate DDMI XFP ( XFP ZR ) 1550nm uncooled DFB with APD Receiver 80km transmission distance
Feature 10Gb/s serial optical interface compliant to 802.3ae, 10GBASE ZR/ZW 1550nm cooled EML transmitter with TEC, APD photo-detector XFP Mechanical interface with bail latch and hot pluggable XFI High
More informationXFP-10G-S40 10G Ethernet XFP Transceiver
XFP, LC Connector, 1550nm Uncooled EML with PIN Receiver, Single Mode, 40KM Features Applications SONET(OC-192)/SDH(STM64) line card 10GBASE-ER (10.3125Gbps) 10GBASE-EW (9.953Gbps) 10GE Ethernet switches
More informationGPP SRC 10Gbps SFP+ Optical Transceiver, 300m Reach
Features GPP-85192-SRC 10Gbps SFP+ Optical Transceiver, 300m Reach Optical interface compliant to IEEE 802.3ae 10GBASE-SR Electrical interface compliant to SFF-8431 Hot Pluggable 850nm VCSEL transmitter,
More information100Gbs QSFP28 CWDM4 Optical Transceiver Module WT-QSFP28-CWDM4
100Gbs QSFP28 CWDM4 Optical Transceiver Module WT-QSFP28-CWDM4 Features Four-channel full-duplex transceiver modules Transmission data rate up to 26Gbit/s per channel Up to 2km transmission of single mode
More information10GBASE-CX4 Copper XFP Transceiver
10GBASE-CX4 Copper XFP Transceiver XFP-CX4 Features 10GBASE-CX4 compliant (IEEE 802.3ak) Overview The XFP-CX4 copper transceiver from MRV Communications provides cost-effective and reliable bandwidth transport
More informationProduct Specification DataSheet
Product Specification DataSheet SFP-10G-ER RoHS Compliant 10Gb/s SFP+ 1550nm 40km Optical Transceiver PRODUCT FEATURES Hot pluggable 10Gb/s serial optical interface Up to 40km on 9/125um SMF Compliant
More informationSFP+ Dual LC 10G SMF 80Km DWDM 50GHz Transceiver. Features. Applications APPLIED OPTOELECTRONICS, INC. A7ELZQxxFDMAx542
Features Applications 10GBASE-ZR Ethernet ( 9.95 to 10.31Gbps ) SONET OC-192 / SDH STM-64 ( 9.953Gbps ) SFP+ Type Dual LC Transceiver C-Band Wavelengths on 50GHz ITU Grid DWDM EML Laser APD Photo Detector
More informationKRN-SF-SMM0310GD 10Gb/s 300m SFP+ Transceiver Hot Pluggable, Duplex LC, +3.3V, 850nm VCSEL, Multi mode
KRN-SF-SMM0310GD 10Gb/s 300m SFP+ Transceiver Hot Pluggable, Duplex LC, +3.3V, 850nm VCSEL, Multi mode Features: Supports 9.95 to 11.3Gb/s bit rates Hot-Pluggable Duplex LC connector 850nm VCSEL transmitter,
More informationSFP+ Dual LC 10G SMF 80Km DWDM 50GHz Transceiver. Features. Applications APPLIED OPTOELECTRONICS, INC. A7ELZQxxFDMAx641
Applications 10GBASE-ZR Ethernet ( 9.95 to 10.31Gbps ) SONET OC-192 / SDH STM-64 ( 9.953Gbps ) Features SFP+ Type Dual LC Transceiver C-Band Wavelengths on 50GHz ITU Grid DWDM EML Laser APD Photo Detector
More information10GBASE-CX4 Copper XFP Transceiver
10GBASE-CX4 Copper XFP Transceiver XFP-CX4 Highlights Overview The XFP-CX4 copper transceiver from MRV Communications provides cost-effective and reliable bandwidth transport of up to 12.5 Gigabits over
More informationElectromagnetic Interference (EMI) FCC Part 15 Class B Compatible with standards. FDA 21CFR and EN60950, EN (IEC) ,2
CFP2-100GB-LR4-LEG 100GBASE-LR4 CFP SMF 1310NM 10KM REACH LC DOM CFP2-100GB-LR4-LEG 100Gbase CFP Transceiver Features Operating optical data rate up to 112Gbps Transmission distance up to 10km CFP MSA
More informationCompact SFP (CSFP) Transceiver
SFP+, 2x Bi-Di, Dual LC Connector, 1270 nm DML for Single Mode Fiber, RoHS Compliant Digital Diagnostics Functions RoHS Pb Features Applications 10G Fibre Channel Links 10Gigabit Ethernet Links 6.144 Gb/s,
More information1250Mbps 850nm MF SFP Transceiver 550m HOLS-PG85Z-LN-CV/PG85Z-LD-CV
Features: Compliant with SFP MSA standard Compliant with IEEE 802.3z 3.3V DC power supply 850nm, VCSEL, 1250Mbps, 550m; Compliance with 10 Base-FL, 100Base-SX and 1000Base-SX Difference LVPECL inputs and
More informationSFP+ Active Optical Cable
SFP+ Active Optical Cable Preliminary Features RoHS-6 compliant High speed / high density: support up to 10 Gb/s bi-directional operation Compliant to industrial standard SFP MSA Low power consumption
More informationGEVISTA. CWDM Pluggable OC-48 SFP Transceiver. Description
CWDM Pluggable OC-48 SFP Transceiver Description The CWDM-OC48-xx-80 is specifically designed for the high performance integrated duplex data transmission over single mode optical fiber. This transceiver
More informationGLC-GE-100FX (100BASE-FX SFP) Datasheet
GLC-GE-100FX (100BASE-FX SFP) Datasheet Features Build-in PHY supporting SGMII Interface 100BASE-FX operation 1310nm FP laser and PIN photo-detector 2km transmission with MMF Standard serial ID information
More informationLiverage Technology Product Specification. 3Gbps Video Single TX or RX. SFP Optical Transmitter or Receiver
Liverage Technology Product Specification of 3Gbps Video Single TX or RX SFP Optical Transmitter or Receiver Content 1. General Description... 1 2. Features... 1 3. Applications... 1 4. Absolute Ratings...
More informationSFP LC 5G SMF DWDM Transmitter. Features. Applications APPLIED OPTOELECTRONICS, INC. A5ILZDxxSDOA0759
APPLIED OPTOELECTRONICS, I. Features Applications 5G Applications XAUI/OBSAI/CPRI (3.125G) Fiber Channel 3xFC (3.1875G) SONET OC48 / SDH STM16 (2.488Gbps) Gigabit Ethernet / 1X/2X Fiber Channel SFP Type
More information2Mbps 850nm MMF SFP Transceiver 2km HOLS-P1850-LD-CV-B
Features: Compliant with SFP MSA standard 3.3V DC power supply 850nm VCSEL, 2Mbps, 2km Built-in dtionsigital diagnostic function Difference LVPECL inputs and outputs Duplex LC connector Compliant with
More informationSFP+ SR Optical Transceiver
Small Form-Factor Pluggable (SFP+) Fibre Optic Transceivers are compact transceivers used to interface networking devices to fibre or copper networking cables in telecom and data applications. We offer
More information1.25Gbps SFP Transceiver
SFP-GE-S-EO 1.25Gbps SFP Transceiver Features Operating data rate up to 1.25Gbps 850nm VCSEL Laser Transmitter 550m with 50/125 µm MMF, 300m on 62.5/125 µm MMF Single 3. 3V Power supply and TTL Logic Interface
More information10Gb/s SFP+ SONET Optical Transceiver TR-PX15E-NSN. (Preliminary)
10Gb/s SFP+ SONET Optical Transceiver TR-PX15E-NSN (Preliminary) Features 10Gb/s serial optical interface compliant to SONET OC192/SDH STM64 and 802.3ae Hardware/Software Rate select function for 8.5G
More informationSF-SM31WD003D-GP / SF-SM55WD003D-GP
SF-SM31WD003D-GP / SF-SM55WD003D-GP Single-Mode 1.25Gbps GBE /FC SC/LC Single-Fiber SFP Transceiver RoHS6 Compliant Features Up to 1.25Gbps Data Links A type: 1310nm FP TX /1550nm RX B type: 1550nm FP
More informationOP7K-W40-27-x Data sheet
Features Compliant with XFP MSA INF-8077i Compliant with IEEE802.3ae 10GBASE-BX Ethernet standard Bi-Direction link distance up to 20km Power consumption less than 1.5W Simplex LC connector Differential
More informationXFP SONET/SDH Single Fiber 10 km transceiver 10G LR SONET OC-192 / STM-64 w/ CDR. Datasheet
SONET/SDH XFP Optical Transceiver Product Features SONET OC-192 / STM-64 w/ CDR 9 SONET/SDH XFP 10 km LR SONET/SDH XFP for SMF @ 10Gbps 1270Tx-1330Rx DFB+PIN Laser 10 km SONET/SDH XFP 0 C - 70 C Temperature
More informationXFP Optical Transceivers for 10km 10G Serial Applications IGF Series IGF-42311J IGF-42312J. -5 C to +70 C Applications. -10 C to +85 C Applications
XFP Optical Transceivers for 10km 10G Serial Applications IGF Series IGF-42311J -5 C to +70 C Applications IGF-42312J -10 C to +85 C Applications The Bookham IGF-4000 Series optical transceiver modules
More informationProduto: 1.25Gbps SFP Optical Transceiver, 550m Reach, with DDM Modelo: V7-SFP-0301D Documentação: Técnica/Datasheet
Produto: 1.25Gbps SFP Optical Transceiver, 550m Reach, with DDM Modelo: V7-SFP-0301D Documentação: Técnica/Datasheet Features Data-rate of 1.25Gbps operation 850nm VCSEL laser and PIN photodetector Compliant
More informationSFCxx100PAxD SFP Dual fibre CWDM ITU CWDM / 100km / OC-48 Multirate.
SFCxx100PAxD_RevA SFCxx100PAxD SFP Dual fibre CWDM ITU CWDM / 100km / OC-48 Multirate. For your product safety, please read the following information carefully before any manipulation of the transceiver:
More informationSO-QSFP-SR-BD QSFP+, 40G, BIDI, duplex MM, LC
SO-QSFP-SR-BD QSFP+, 40G, BIDI, duplex MM, LC FEATURES: Compliant to the 40GbE XLPPI electrical specification per IEEE 802.3ba-2010 Compliant to QSFP+ SFF-8436 Specification Aggregate bandwidth of > 40Gbps
More information40GBase QSFP+ PSM4 1.5km Optical Transceiver
40GBase QSFP+ PSM4 1.5km Optical Transceiver PRODUCT FEATURES Supports 41.2 Gb/s aggregate bit rates Link Distance up to 1.5km over SMF fiber 4 parallel 10Gbps full duplex channels Standard 12-fiber MPO/MTP
More informationDatasheet. XFP Optical Transceiver Product Features XFP-10G-K010B33. Applications. Description. XFP Single Fiber 10 km transceiver 10G LR Ethernet
XFP Optical Transceiver Product Features 10GBASE-LR/LW Ethernet 9 XFP 10 km LR XFP for SMF @ 10Gbps 1330Tx-1270Rx DFB+PIN Laser 10 km XFP 0 C - 70 C Temperature - Extended/Industrial Available 2-Wire Interface
More informationPlatinum OEM Series. Datasheet Tunable XFP Optical Transceiver Product Features PXFT-10GXXXK040. Applications
Designed for OEM networks such as Cisco, HP, Juniper, Brocade, Alcatel etc. Datasheet Tunable XFP Optical Transceiver Product Features Exclusive Japanese OSAs for Ultimate Reliability SONET OC-192 / STM-64
More informationTunable OTN XFP MSA Compliant DWDM 11.1Gb/s Transceiver with Integrated G.709 and FEC
Tunable OTN XFP MSA Compliant DWDM 11.1Gb/s Transceiver with Integrated G.709 and FEC Management XFI Electrical Interface Description Menara Networks Tunable OTN XFP DWDM transceiver combines carrier grade
More informationDatasheet. XFP Optical Transceiver Product Features XFP-10G-K080DXX. Applications. Description. XFP DWDM 80 km transceiver 10G ZR Ethernet
XFP Optical Transceiver Product Features 10GBASE-ZR/ZW Ethernet 23 XFP 80 km ZR XFP for SMF @ 10Gbps 100GHz (C-Band) EML+APD Laser 80 km XFP 0 C - 70 C Temperature - Extended/Industrial Available 2-Wire
More informationDescription The Gigalight s100gb/s transceiver module for optical communication applications compliant to 100GBASE-SR4 of the IEEE P802.3bm standard.
100GBASE-SR4 CFP4 Optical Transceiver GF4-M101-SR4C Features Hot pluggable CFP4 MSA form factor Supports 103.1Gb/s to 112.2Gb/s aggregate bit rates Compliant to IEEE 802.3bm 100GBASE-SR4 Power class 2
More information