Universal Safety Photo Eye UL MONITORED DEVICE
|
|
|
- Cecil Russell
- 5 years ago
- Views:
Transcription
1 IRB-MON Universal Safety Photo Eye UL MONITORED DEVICE Operating Instructions
2 CAUTIONS AND WARNINGS This product is an accessory or part of a system. Always read and follow the manufacturer s instructions for the equipment you are connecting this product to. Comply with all applicable codes and safety regulations. Failure to do so may result in damage, injury or death! 1. Read and follow all operation instructions. 2. Always follow gate operator manufacturer installation instructions regarding installation of Type B1 sensor to the operator. 3. Disable the gate so it is unable to move GENERAL DESCRIPTION The IRB-MON is a thru-beam photo eye and is an external entrapment protection device type B1, non-contact sensor for use with automatic gates and doors. The light beam is near infrared and pulses at a rate of 300/second (300Hz). The IRB-MON provides a signal to the gate or door operator that the beam is not obstructed. The operating range is up to 115ft. The IRB-MON operates over a wide range of 6-35VDC and 12-24VAC. A green alignment indicator on the receiver provides status information at a glance, making set-up and alignment easy. The IRB-MON includes three selectable operating configurations providing compatibility with most operators that accommodate monitored external entrapment protection devices per UL Refer to operator installation instructions for proper configuration selection: CONFIGURATION 0 - NON-MONITORED and MONITORED Intended for use with operators that require simple relay contact activation to indicate beam obstruction. CONFIGURATION 1 MONITORED, HEARTBEAT 300Hz / 0Hz Intended for use with operators designed to accept a heartbeat form of monitoring, 300Hz when aligned, no obstruction, 0Hz when beam is obstructed. CONFIGURATION 2 MONITORED, HEARTBEAT 300Hz / 2Hz / 0Hz Intended for use with operators designed to accept a heartbeat form of monitoring, 300Hz when aligned, no obstruction, 2Hz when beam is obstructed, and 0Hz for a failure. IRB-MON Operating Instructions 2
3 Configuration settings - Remove power when changing Configuration settings. SW4 SW3 SW2 SW1 FUNCTION X X OFF OFF Configuration 0 - relay operation, no frequency output X X OFF ON Configuration 1 - heartbeat output, 300Hz, 0Hz, no relay activation X X ON OFF Configuration 2 - heartbeat output, 300Hz, 2Hz, no relay activation ON X X X Dark on - N.O. contact closed when beam obstructed OFF X X X Light on N.O. contact closed when beam is not obstructed Green status indicator IRB-MON-T (transmitter) ON Power IRB-MON-R (receiver) Flashing Blocked beam or not aligned IRB-MON-R (receiver) ON Aligned SPECIFICATIONS Operating range up to 115 ft. (35m) Detection angle 24 o Sensitivity adjustment potentiometer Power indicator Green LED Detect indicator Green LED (flashing) Mode selection switch 3 modes, relay output, pulsed (3 frequency), pulsed (2 frequency) Relay output operation Light on/dark on selection Relay output Form C contacts (NO, COM, NC) Power protection Thermal fuse Transmitter power cycle >300mS (for use in Configuration 0 Monitored) Power Supply 6 35 VDC, VAC (Configuration 0 RELAY only) Current (Config. 1 and 2) 15mA (12VDC, includes TX and RX wired in parallel) Current (Config. 0) 60mA (relay activated) Operating temperature -40 F 170 F ( C) Environmental NEMA 4X Dimensions (L x W x H) 2.3 (57mm) x 2.6 (65mm) x 3.7 (94mm) Weight TX lbs (159 g), RX 0.35 lbs (159 g) Connections TX-2 terminal, RX-5 terminal IRB-MON Operating Instructions 3
4 INSTALLATION Install the IRB-MON according to instructions from the gate operator manufacturer. The intent of External Entrapment Protection Device Type B1 non-contact sensor is to protect a person from being accidentally injured by the moving gate or door. DO NOT USE 12-24VAC IN PULSE CONFIGURATIONS. 1. Disconnect the IRB-MON from power before installing or servicing the device. 2. Always follow the instructions of the gate operator manufacturer regarding installation of type B1 sensors on the gate operator. The instructions of the gate operator manufacturer always supersede any instructions given in this or any other instructions by EMX Industries Inc. 3. Connect the IRB-MON power supply per requirements indicated in the specification table. 4. When using the relay outputs, do not exceed the voltage/current ratings indicated in the specification table. 5. Connect power to the terminals on the transmitter marked TX, polarity is not required. Refer to the CONFIGURATION DIAGRAMS for power wiring. 6. Connect power to terminals marked POWER INPUT on the receiver, marked RX polarity is not required. Refer to the CONFIGURATION DIAGRAMS for power wiring. 7. For CONFIGURATION 0 ONLY. Operators that require normally closed contact for entrapment protection, connect terminal NC and COM to the designated terminals in the gate operator. Operators that require normally open contact for entrapment protection, connect terminals COM and NO to the designated terminals in the gate operator. 8. Install the IRB-MON according to instructions from the gate operator manufacturer. The intent of External Entrapment Protection Device Type B1 non-contact sensor is to protect a person from being accidentally injured by the moving gate or door. 9. The IRB-MON is housed in a NEMA 4X enclosure. To insure the integrity of the enclosure make sure the covers are attached and closed tight using all four plastic screws provided. The wiring to the enclosure must enter via UL Listed watertight fitting such as a strain relief or watertight conduit connector. 10. The IRB-MON must be powered by Class 2 circuits only, wiring must be segregated from other circuits or insulation must be provided that is suitable for the highest voltage for those circuits. IRB-MON Operating Instructions 4
5 VERIFY INSTALLATION AND OPERATION Verify proper operation of the IRB-MON according to instructions from the gate operator manufacturer. The intent of External Entrapment Protection Device Type B1 non-contact sensor is to protect a person from being accidentally injured by the moving gate or door. 1. Verify that the IRB-MON transmitter and receiver in line of sight and apply power. 2. Place an obstruction (ex. hand) between the IRB-MON transmitter and receiver. The green LED on the receiver is flashing. Check the operator control board that the safety input is actuated. 3. Remove the obstruction and green LED will be on. 4. If the IRB-MON does not respond to the obstruction, lower the sensitivity by adjusting the SENSITIVITY pot counter-clockwise. 5. If the IRB-MON indicates an obstruction when there is no obstruction, increase the sensitivity by adjusting the SENSITIVITY pot clockwise. 6. Follow gate/door manufacturer s installation instructions and safety checks to verify that the IRB-MON is operating properly. TROUBLESHOOTING GUIDE Symptom Possible cause Solution Does not detect obstruction of Sensitivity too high Adjust SENSITIVITY pot beam counter-clockwise Green LED flashes continuously (indicating an obstruction when an obstruction is not present) Receiver activates but does not transmit signal to operator Signal is reflecting off another surface Sensitivity too low Transmitter does not have power Receiver does not see transmitter Faulty connection between receiver and operator control input Check area for highly reflective surfaces Adjust SENSITIVITY pot clockwise Check power source for transmitter Make sure transmitter and receiver have line of sight alignment Verify all wires and terminal connections IRB-MON Operating Instructions 5
6 ORDERING INFORMATION IRB-MON Infrared photocell includes transmitter and receiver IRB-HD-SET Protective hood, aluminum, gold anodized IRB-SD-SET Protective hood, steel, gray powder-coat IRB-BR Mounting bracket, L shape IRB-SP Strain relief, water-tight IRB-S Nylon screws, set of 4 IRB-MON Operating Instructions 6
7 IRB-MON Operating Instructions 7
8 4564 Johnston Parkway Cleveland, Ohio United States of America Technical Support: (216) Sales: (216) Fax (216) IRB-MON Operating Instructions 8
IRB-MON O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY PHOTOEYE U L M O N I T O R E D DEVICE
O P E R A T I N G I N S T R U C T I O N S IRB-MON UNIVERSAL SAFETY PHOTOEYE U L 3 2 5-2 0 1 6 M O N I T O R E D DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales
IRB-MON UNIVERSAL SAFETY PHOTOEYE OPERATING UL MONITORED DEVICE
IRB-MON UNIVERSAL SAFETY PHOTOEYE OPERATING UL325-2016 MONITORED DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales Inquiries: salessupport@emxinc.com Technical Support:
IRB-RET O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L MONITORED DEVICE
O P E R A T I N G I N S T R U C T I O N S IRB-RET UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L 3 2 5-2 0 1 6 MONITORED DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884
IRB-RET O P E R A T I N G I N S T R U C T I O N S UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L M O N I T O R E D DEVICE
O P E R A T I N G I N S T R U C T I O N S IRB-RET UNIVERSAL SAFETY RETROREFLECTIVE PHOTOEYE U L 3 2 5-2 0 1 6 M O N I T O R E D DEVICE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216
OPERATING INSTRUCTIONS
TM CarSense 303-L OPERATING INSTRUCTIONS LOGIC INTERFACE 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales Inquiries: salessupport@emxinc.com Technical Support: technical@emxinc.com
Operating Instructions
CS202S CarSense Vehicle Motion Detector Operating Instructions CAUTIONS AND WARNINGS Never use the CS202 as a safety reversing or presence detection system. The CS202 requires that a vehicle be moving
Bluetooth Enabled Access Control MODEL BG-FE. Operating Instructions
BlueGuard FE Bluetooth Enabled Access Control MODEL BG-FE Operating Instructions CAUTION AND SAFETY INFORMATION IMPORTANT: If the equipment is used in a manner not specified in this manual, the protection
CarSense202 O P E R A T I N G I N S T R U C T I O N S V E HI C L E M O T I O N D E T E C T O R Johnston Parkway, Cleveland, Ohio 44128
O P E R A T I N G I N S T R U C T I O N S CarSense202 V E HI C L E M O T I O N D E T E C T O R 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales Inquiries: salessupport@emxinc.com
General-Purpose Photoelectric Sensor
General-Purpose Photoelectric Sensor Compact Limit Switch Style with Universal Supply FET output allows for solid state switching of AC or DC Universal AC/DC power supply Choose cable or connector types
COMMONLY USED 5.AFETY SENSORS. Photocell (Reflector) CLOSING Direction. Photocell (Reflector) CLOSING Direction OA4RO E.3IC-RIOIC4 EA4X IRB-RET
MLY USED 5.AFETY SENSORS 0----- OA4RO E.IC-RIOIC4 Direction. Set switch to "LIGHT ". Wire V power to photocell. Wire to photocell N0 Wire to photocell C- 4. Align photocell to reflector 5. Adjust sensitivity
Compact Coded Magnetic Safety Interlock Switch and Control Units
C Conforms to EN292, EN60204-1, EN954-1, EN1088, EN60947-5-3, EN947-5-3, EN50081, EN50082, EN61000-6-2 UL and C-UL listed, TUV certified Description R US Compact Coded Magnetic Safety Interlock Switch
onlinecomponents.com
R General-Purpose Fiber-optic Sensor Compact Limit Switch Style with Universal Supply H FET output allows for solid state switching of AC or DC H Universal AC/DC power supply H Choose cable or connector
The Solution. Multi-Input Module IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
The Solution Multi-Input Module INSTALLATION INSTRUCTIONS Model: MIM-62 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION MIM-62 connects up to 6 monitored entrapment protection
ReFlx 100 PLUS COLLISION AVOIDANCE SYSTEM
100 PLUS COLLISION AVOIDANCE SYSTEM The 100 Plus collision avoidance system is intended for use with bridges and trolleys to prevent collisions or to limit the approach of adjacent bridges or trolleys.
Special-Purpose Photoelectric Sensors
Special-Purpose Photoelectric Sensors Miniature Sensors with Separate Amplifiers Fit Tight Spaces Fast, 1 ms response time Light incident indicator on sensor Dust-resistant flat lens surface New, thin
OPERATING PRINCIPLES FOR PHOTOELECTRIC SENSORS
OPERATING PRINCIPLES FOR PHOTOELECTRIC SENSORS Photoelectric These sensors use light sensitive elements to detect objects and are made up of an emitter (light source) and a receiver. Four types of photoelectric
VSS Nederland Video Systems
VSS Nederland Video Systems Infra Red & White Light Illuminators User s Guide Overview 1. Description A complete range of infra-red and white light illuminators for CCTV, the Visible and Invisible range
Safety switches for hinged doors
C Safety switches for hinged doors Selection diagram FR FM FX FZ FK 18 7 9 snap action overlapped CONTACT BLOCKS 21 NC 1NO+ CONDUIT ENTRIES Threaded conduit entries (standard) With cable gland assembled
Safety switches with separate actuator
A Safety switches with separate actuator Selection diagram VF KEYF VF KEYF1 VF KEYF2 VF KEYF3 VF KEYF VF KEYF ACTUATORS CONTACT BLOCKS 9 snap action overlapped FD FP FL FC 21 22 33 3 3NC 2NO+1NC 1NO+ CONDUIT
Series 28 Universal Sensors
Series 8 Universal Sensors Diffuse Mode with Background Suppression See pages 548-553 Features: Sharp sensing range cut-off Choice of infrared, visible red and laser light sources Sensing Range: 400 mm,
MLS7A Series. Photoelectric Sensors. Heavy-Duty Retro-Reflective Sensors. Photoelectric MLS7A Series Heavy Duty PEPPERL+FUCHS 529
Retro-Reflective Mode See page 53 Sensing Ranges: 3m Outputs: NPN MLS7A Series Heavy-Duty Retro-Reflective Sensors Heavy Duty Cast aluminium housing Side mount or flange mount Photoelectric MLS7A Series
Series 3700 Screw Terminal Assemblies Installation Instructions
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY www.keithley.com Series 3700 Screw Terminal Assemblies Installation Instructions Introduction This document contains handling
Instruction Manual. M Pump Motor Controller. For file reference, please record the following data:
Instruction Manual M Pump Motor Controller For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your
The Programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits.
Peripheral Relay The Programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits. Up to 16 Cards can be connected to a multi-loop panel
8000 Series: Installation Supplement R2-1-12
8000 Series: Installation Supplement R2-1-12 Smartscan Incorporated, 33083 Eight Mile Road, Livonia MI 48152 Tel: (248) 477-2900 Fax: (248) 477-7453 Web: www.smartscaninc.com SMARTSCAN INCORPORATED Livonia,
MLV41 Series Miniature Sensors
MLV41 Series Miniature Sensors Diffuse Mode with Background Suppression See pages 5-53 Features: Etended sensing range compared to similar housings High insensitivity to target color Sensing Range: 35
ReFlx. ReFlx 100 Collision Avoidance System Instruction Manual Page 1 6/30/99
100 COLLISION AVOIDANCE SYSTEM The 100 collision avoidance system is intended for use with bridges and trolleys to prevent collisions or to limit the approach of adjacent bridges or trolleys. The system
THE ARIA. LED AREA LIGHT. eran industrial. ARL SERIES
AREA LIGHT eran industrial. ARL SERIES AREA LIGHTS THE SUPERIOR ARL SERIES ARL 460 120W 100W 65W ARL 480 250W 200W 150W ARL 460 380W 300W WE CONTINUE TO BRING ADVANCED TECHNOLOGY TO THE LIGHTING INDUSTRY.
Safety switches with manual mechanical delay and separate actuator
D Safety switches with manual mechanical delay and separate actuator Selection diagram VF KEYF VF KEYF1 VF KEYF VF KEYF VF KEYF7 VF KEYF ACTUATORS MECHANICAL DELAY C L L0 Short knob 0 sec. Short knob sec.
Table of Contents. General Information. Document Sure-Aire Flow Monitoring System. User and Service Manual WARNING CAUTION
Document 476092 User and Service Manual Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
Nokeval. FD100 series. User Manual
Nokeval FD100 series User Manual Contents Document information... 2 FD100A4 and FD100A6 field displays... 3 Power supply connection... 4 Configuring... 5 Specifications... 7 Document information Device
NO: PH-185 PRODUCT: E3JK Photoelectric Sensors DATE: May 2014 TYPE: Discontinuation Notice
NO: PH-185 PRODUCT: E3JK Photoelectric Sensors DATE: May 2014 TYPE: Discontinuation Notice E3JK Universal AC/DC Supply Voltage Photoelectric Sensors to be Discontinued February 2015; Replace with E3JM
Operating Instructions. Power Supply & Latching Relay For Switches Model: RL manual_rl-6000_1016
Operating Instructions Power Supply & Latching Relay For Switches Model: RL-6000 manual_rl-6000_1016 1. Contents 1. Contents...2 2. Note...3 3. Instrument Inspection...3 4. Regulation Use...3 5. Operating
Photoelectric Sensor
Sensing Supply Voltage Output 3m 1.cm,2m 10cm 2 to 20 VAC, 0/60 Hz to200ma, 20 VAC 100 ma, 2 VDC Photoelectric Sensor Threaded Cylindrical M1 Size Sensors with Built-in Amplifier Chemical resistant, ABS
Magnetically Actuated Safety Interlock Switches
Conforms to EN10, EN292, EN020-1 CSA and BG approved Actual Size Magnetically Actuated Safety Interlock Switches Large selection choose from a large selection of contact configurations housed in plastic,
INSTALLATION INSTRUCTIONS
LIGHTING CONTROL PANELS 16 AND 24 RELAYS INSTALLATION INSTRUCTIONS INSTALLATION OVERVIEW The installation instructions contained in this document are provided as a guide for proper and reliable installation.
Rotork Fairchild PAX1 Linear Actuator User s Manual
Rotork Fairchild PAX1 Linear Actuator User s Manual Product Overview The PAX1 is a flexible low voltage DC powered linear actuator featuring a 5 mm maximum thrust rod stroke moving at speeds up to 0 mm/min
25 m 5 m 1 m. Part Number Mounting bracket. E39-LU1 Mounting bracket for E39-R1 reflector
Sensing distance Supply voltage 25 m 5 m 1 m General-Purpose Photoelectric Sensor Universal 24 to 240 VAC 24 to 240 VDC 3A, 250 VAC 400 ma 240 VAC 100 VDC Compact Limit Switch Style with Universal Supply
Safety Contacts: AC models MA-1 thru 5, 10, 12, 13, 16 1 N/C MA-13, 16, 21 2 N/C DC models MA-12, 13, 14, 16 1 N/C MA-13, 15, 16, 20, 21 2 N/C
r Safety Interlock Switches MA Series MA Magnetically Actuated Safety Interlock Switches Large selection choose from a large selection of contact configurations housed in plastic to satisfy most application
D6030S - D6030D INSTRUCTION MANUAL. D SIL 3 Switch/Proximity Detector Repeater Relay Output. Models D6030S, D6030D
D600S - D600D INSTRUCTI MANUAL SIL Switch/Proximity Detector Repeater Relay, DIN Rail, Models D600S, D600D D600 - SIL Switch/Proximity Detector Repeater Relay G.M. International ISM0- Characteristics General
DMC2. Installation Guide Version 1.0. Area for main photograph. Area for insert photo. W: 46.1mm up to 79 mm H: 46.1mm
Area for main photograph Area for insert photo W: 46.1mm up to 79 mm H: 46.1mm X: 12.6mm absolute on page Y: 132.6mm abs on page This insert has a shadow DMC2 Installation Guide Version 1.0 Contents DMC2
Rhino Buffer Module PSM24-BFM600S. Operating Instructions
Rhino Buffer Module PSM24-BFM600S Operating Instructions RHINO BUFFER MODULE PSM24-BFM600S Description The PSM24-BFM600S Buffer Module will hold the output voltage of a 24 VDC power supply after brownouts
For full product information, visit Use the SpeedSpec code or scan the QR Code for quick access to the specific web page.
R Safety Interlock Switches MA Series MA For full product information, visit www.sti.com. Use the SpeedSpec code or scan the QR Code for quick access to the specific web page. Magnetically Actuated Safety
F3ET Lightcurtain in robust aluminium housing
Lightcurtain in robust aluminium housing FET Lightcurtain in robust aluminium housing The FET lightcurtains provide a reliable area monitoring in a robust housing. The M2 -pin connectors and optical synchronisation
INSTRUCTION MANUAL. SIL 3 Switch/Proximity Detector Repeater Relay Output, Termination Board Models D6032S, D6032D
D603S D603D INSTRUCTI MANUAL SIL 3 Switch/Proximity Detector Repeater Relay, Termination Board Models D603S, D603D D603 SIL 3 Switch/Proximity Detector Repeater Relay G.M. International ISM0400 General
MHP PHOTOELECTRIC. Sensors and Switches NOTICE GENERAL INFORMATION
MHP PHOTOELECTRIC Catalog Listing Description SDS-C2MHP-R-G retroreflective, infrared, range 18 ft. (5,5 m) SDS-C2MHP-D-G diffuse, infrared, range 18 in. (457,2 mm) SDS-C2MHP-P-G polarized retroreflective,
Safety switches with separate actuator
4 Safety switches with separate actuator Selection diagram VF KEYD VF KEYD1 VF KEYD VF KEYD VF KEYD VF KEYD6 VF KEYD VF KEYD10 ACTUATORS CONTACT BLOCKS 6 snap action overlapped FR FX FK FW 0 1 4 NC NO+1NC
BMX DDM Mixed Relay Input/Output module
Modicon M340 Using Unity Pro BMX DDM 16025 35012474 07/2012 BMX DDM 16025 Mixed Relay Input/Output module 22 Subject of this Section This section presents the BMX DDM 16025 module, its characteristics,
BOP QUICK START GUIDE 100W, 200W, 400W. KEPCO An ISO 9001 Company. BIPOLAR OPERATIONAL POWER SUPPLY WARNINGS I INTRODUCTION II SAFETY.
QUICK START GUIDE I INTRODUCTION KEPCO An ISO 9001 Company. BIPOLAR OPERATIONAL POWER SUPPLY 1.1. SCOPE OF MANUAL. This Quick Start Guide covers simple installation and local operation of the Kepco 100W,
Output Signal. Temperature 22DTH-56M BACnet DC V, DC V. Electrical Data Power Supply DC V, ±10%, 0.7 W
Duct Sensor Humidity / Temperature For measuring the relative or absolute humidity and temperature in duct applications. The measured values and absolute humidity, dewpoint and enthalpy are transmitted
BlueWave ~ Intelligent Energy Control. Installation and User Manual for BW2/C and BW3/C versions. Quick Guide
BlueWave ~ Intelligent Energy Control Installation and User Manual for BW2/C and BW3/C versions Quick Guide Press button to override or activate Channel 1 Press button to override or activate Channel 2
ASI Systems ML5740A Series
ML5740A Series Electric Linear Valve Actuators Non-Spring Return APPLICATION The ML5740A series actuators operate standard ASI Systems valves in heating, ventilating and air conditioning (HVAC) applications.
ASI Systems ML5720A Series
ML5720A Series Electric Linear Valve Actuators Non-Spring Return APPLICATION The ML5720A series actuators operate standard ASI Systems valves in heating, ventilating and air conditioning (HVAC) applications.
T4HD: Installation Supplement R8.1.13
THD: Installation Supplement R8.. Smartscan Incorporated 08 Eight Mile Road Livonia MI 8 Tel: (8)77-900 Fax: (8) 77-7 Web: www.smartscaninc.com Smartscan Incorporated Livonia, Michigan THD The use of this
ZC Series Zone Monitoring Controllers
ZC Series Zone Monitoring Controllers Installation Instructions MANUAL Reset Controllers Model Description Part Number ZC-1 1 Zone Controller 0421 ZC-2 2 Zone Controller 0422 ZC-3 3 Zone Controller 0423
Level-Lance Model 5400A
Sales Manual Section 100 PRODUCT SPECIFICATION 5400A GENERAL DESCRIPTION The ROBERTSHAW Level-Lance Model 5400A is a microprocessor based, multi-point On-Off capacitance type level detection system. Utilizing
Versatile Safety Interlock Switch with Guard Door Locking
R Conforms to EN1088, EN60947-5-1, EN292, EN60204-1 UL and C-UL listed, BG approved Versatile Safety Interlock Switch with Guard Door Locking High locking force of 450 pounds locks guard door shut until
SELECTRONIX, INC. SUPERSTEP SERIES 4000 SEQUENCING STEP CONTROLLERS WOODINVILLE, WA INSTALLATION & OPERATING ADDENDUM LOAD LIMIT INPUT CONFIGURATIONS
SELECTRONIX, INC. WOODINVILLE, WA SUPERSTEP SERIES 4000 SEQUENCING STEP CONTROLLERS INSTALLATION & OPERATING ADDENDUM LOAD LIMIT INPUT CONFIGURATIONS Rev 03/10/19 2 1 Various DC Voltage - 100 % Load Limit
Differential Liquid/Gas Pressure Transmitter
Installation Instruction Differential Liquid/Gas Pressure Transmitter Catalog Number(s) 1414-CPZ10FWFAA, 1414-IPZ10FWFAA Explosion Hazard WARNING Do not use in an explosive or hazardous environment, with
Installation, Operation and Maintenance Manual
Document 481200 VGD-100 Vari-Green Drive Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
Magnetically Actuated Safety Interlock Switches
Rev. 7.07 C US Conforms to EN1088, EN292, EN6020-1 CSA approved MA Series Magnetically Actuated Safety Interlock es Large selection choose from a large selection of contact configurations housed in plastic
DTS 310. DIN Rail Mounted, Indoor Rated Revenue Grade Electrical Sub-meter. Page 1. Measurlogic MQ A
DTS 310 DIN Rail Mounted, Indoor Rated Revenue Grade Electrical Sub-meter Page 1 1 PRODUCT OVERVIEW... 3 1.1 SUPPLIED ITEMS... 3 1.2 DOCUMENT CONVENTIONS... 4 1.3 PRODUCT SPECIFICATION... 4 1.3.1 Current
MANUAL (TRANSLATION) RAY-LG X5XX
Features Category 2, Type 2, E Device acc. EN 12453:2014, clause 5.5.1 Safety Cat. 2, PL d according to EN ISO 13849-1 Automatic Door Recognition ( Blanking ) with partial Door Opening Certified according
onlinecomponents.com
FF-RE59292 Extension Module Instructions for use (pending) (pending) IMPROPER INTALLATION Consult with U and/or European safety agencies and their requirements when designing a machine control, interface
EX12LED Infrared LED Illuminator
Precision Engineered Opto-Electronics INSTALLATION INSTRUCTIONS EX12LED Infrared LED Illuminator MAN-12LED-06 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep this instruction. 3. Heed
Power Over Fiber USER GUIDE. SYSTEM INSTALLATION INFORMATION Description. The leader in rugged fiber optic technology. RLH Industries, Inc.
USER GUIDE RLH Industries, Inc. The leader in rugged fiber optic technology. U-145 2018A-0119 Power Over Fiber SYSTEM INSTALLATI INFORMATI Description Our patented Power Over Fiber (PoF) system provides
MULTIBAND Dual Radio V4
Dual Radio V4 WI FI Compatibility Speed Package Contents: Multiband Dual Radio v4 Mounting Bracket (Include: 2 stainless & steel U-Bolt, 1 Bracket and 4 screw nuts) 100-240VAC 48VDC, 350 ma PoE Injector
Legacy Sensor Products
Legacy Sensor Products 20 Series E65 Miniature Series E65 Miniature Series.1 Product........................................ Product Selection Guide................................... Technical Data and
Conveyor Belt Alignment Switches from IDEM
Conveyor Belt Alignment Switches from IDEM Data Sheet Die-Cast Models Python Line Series Stainless Steel Models Using Conveyor Belt Alignment Switches Application: Conveyor Belt Alignment switches are
APPLICATION CONTROL GUIDELINES. IntelliROL Power Supply PN Revision Date: March 15, 2017
APPLICATION CONTROL GUIDELINES IntelliROL Power Supply PN 1176718 Revision Date: March 15, 2017 Table of Contents List of Tables...3 TGW Safety Recommendation...4 Warnings and Safety Instructions...5 Introduction...6
AEGIS UFLED INSTALLATION INSTRUCTIONS
_ TM AEGIS UFLED INSTALLATION INSTRUCTIONS Derwent Systems Ltd. Tel: +44 1670 730187, Fax: +44 1670 730188 Email: Sales@DerwentCCTV.com AEGIS UFLED INSTALLATION INSTRUCTIONS 1. Description 2. Specification
Description. Features. Ultrasonic Sensors 873P Analog or Discrete Output INTRODUCTION. 873P Analog Output18 mm. 873P Discrete Output30 mm
INTRODUCTION 873P Analog Output18 mm 873P Discrete Output30 mm Description Bulletin 873P Ultrasonic Sensors are self contained solid state devices designed for noncontact sensing of solid and liquid objects.
PRECISION LED HIGH MAST LIGHTING
THE PRECISION LED HIGH MAST LIGHTING SPEC WITH CONFIDENCE 1 TOLL-FREE: 888-410-5337 FAX: 614-868-5344 2017 SpecGradeLED INTRODUCING THE SpecGrade LED s rugged Navigator is engineered to seamlessly integrate
Legacy Sensor Products
Legacy Sensor Products 20 Series E65 Miniature Series E65 Miniature Series.1 Product.............................................. 460 How to Order.................................................. 460
3RG7 Opto-BERO Photoelectric Proximity Switches
K 80 Sensing range 2 m (energetic sensor) Diffuse sensors Modulated infrared light DC or AC/DC M 12 plug or moulded plastic joint IP 67 ON-delay, OFF-delay, pulse shaping Timer 0.01 s to 10 s Enabling
optical sensors through-beam, retro-reflective, dif. reflection sensors 3000 transmitter with test input robust metal housing
design 12 x 12 x 64mm 12 x 12 x 69mm 12 x 12 x 74mm operating distance retro-reflective sensor operating distance diffuse reflection sensor sensing range up to 6.0m up to 4.0m up to 1.2m metal housing
InView Communication Modules
Installation Instructions InView Communication Modules Catalog Numbers 2706-PxM, 2706-PxK, 2706-PxP Topic Page About This Publication 1 Important User Information 2 Power Supply Requirements 3 Mount the
ML20 Series Long-Range Miniature Sensors
Diffuse Mode See pages 486-487 Features: Cross-talk immune for 2 units Divergent beam versions available Sensing Ranges: mm, 1 m Output: NPN, PNP Thru-Beam Mode See page 489 Features: Alignment in lens
InView Marquee Message Display
Installation Instructions InView Marquee Message Display Introduction These instructions show how to change the serial address and how to mount InView series signs with NEMA Types 4, 4X, and 12 enclosures.
Rhino Redundancy Module PSM24-REM360S. Operating Instructions
Rhino Redundancy Module PSM4-REM360S Operating Instructions RHINO REDUNDANCY MODULE PSM4-REM360S Description With this module and two power supplies of the PSM series (78, 90, 56, 80 and 360 watt models),
SMARTSCAN INFORMATION
SMARTSCAN INFORMATION SL4 (014) SERIES SAFETY LIGHT CURTAINS HANDBOOK Smartscan Ltd, Pywell Road, CORBY, NN17 5XJ, UK, Tel: +44 (0) 1536 401313, Fax: +44 (0) 1536 268954, Email: sales@smartscan.co.uk,
DC Outdoor Power Supply/Chargers
DC Outdoor Power Supply/Chargers Installation Guide Models Include: WayPoint3 WayPoint7-2.5A @ 12VDC or 24VDC. - 6A @ 12VDC or 24VDC. - 115/230VAC input. - 115VAC input. WayPoint5 WayPoint7V - 4A @ 12VDC
For full product information, visit Use the SpeedSpec Code or scan the QR Code for quick access to the specific web page.
R Safety Interlock Switches TL8012-S TL8012 For full product information, visit www.sti.com. Use the SpeedSpec Code or scan the QR Code for quick access to the specific web page. Versatile Safety Interlock
onlinecomponents.com
Universal Voltage Terminal Photoelectric Universal AC/DC Photoelectric Sensor with Built-in Timer Easy-to-wire terminal block Built-in timer offers selectable ON-delay, OFF-delay and one-shot Relay or
AD-7830 Servo Amplifier
Instruction Manual IM-0606 AD-7830 Servo Amplifier Table of Contents General Information... 2 Introduction... 2 Receiving/Inspection... 2 Storage... 2 Equipment Return... 2 Abbreviations Used in This Manual...
E3S-A. Built-in Amplifier Photoelectric Sensor (Medium Size) Ordering Information. Built-in Amplifier Photoelectric Sensors. Horizontal. 7 m.
Built-in Amplifier (Medium Size) ES-A CSM_ES-A_DS_E Be sure to read Safety Precautions on page 0. Ordering Information Built-in Amplifier s Red light Infrared light Sensing method Appearance Connection
Instruction Manual: IM E
Innovative Technology TVSS Products The I.T. Equalizer Installation Instruction Manual: IM01005011E Rev. 2 May 2009 Contents Page 1 Introduction... 1 1.1 Scope... 1 1.2 I.T. Equalizer Catalog Numbering
Operation mode. Output configuration. Relay DC SSR. Light-ON Dark-ON (switch selectable) Relay DC SSR. Relay DC SSR
Built-in Power Supply Photoelectric Sensor CSM DS_E_12_3 Model Contribute to Overall Cost Reduction erminal Block Models Easy to wire and adjust. For the most recent information on models that have been
ML17 Series Tru-Vue TM Sensors
ML7 Series Tru-Vue TM Sensors Diffuse Mode with Background Suppression See page 44 Features: Ver low color sensitivit Tamper-proof housing with no eternal adjustments Sensing Range: 5 mm Output: 4-in-
Operating instructions. Speed monitor D / / 2014
Operating instructions Speed monitor D200 80005257 / 00 05 / 2014 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5 2.2 Target group...5
Suitable for detecting transparent films or transparent bottles
Ultrasonic Sensor Suitable for detecting transparent films or transparent bottles Reliable detection of transparent objects The sensor reliably detects transparent films or transparent objects. Only 16
M-Series 415 & in 1 Elevator Light Curtain. Installation Manual
M-Series 415 & 405 2 in 1 Elevator Light Curtain Installation Manual Table of contents PRINCIPLE 1 INSTALLATION 2 MOUNTING THE POWER SUPPLY MS721 6 POWER SUPPLY MS721 AND EARTH CONNECTION 8 FUNCTIONAL
ML17 Series Tru-Vue TM Sensors
ML7 Series Tru-Vue TM Sensors Diffuse Mode with Background Suppression See page 44 Features: Ver low color sensitivit Tamper-proof housing with no eternal adjustments Sensing Range: 5 mm Output: 4-in-
Color Mark Photoelectric Sensor E3S-VS
Sensing Supply voltage Output 12 to 80 ma, with 1.5 to 4 ma constant current source; 1.2 cm, 5 cm 100 ma, Color Mark Photoelectric Sensor Small Color Mark Sensor With Built-In DC Amplifier Fast, 1 ms maximum
User's Manual: Series 250T Potentiometer/Slidewire Input, Two-Wire Transmitters
User's Manual: Series 250T Potentiometer/Slidewire Input, Two-Wire Transmitters INTRODUCTION: Table of Contents Page Introduction 1 Description 1 Specifications 2 Specifications (Display Option) 3 Installation
PANELITE ENCLOSURE LIGHTS OVERVIEW
SPEC-00581 H763.422.2211 763.422.2600 ELECTRICAL LIGHTING PACKAGES ELECTRICAL LIGHTING PACKAGES PANELITE ENCLOSURE LIGHTS OVERVIEW FEATURES Slim profile allows light to be tucked up out of the way for
Photoelectric Sensors E3F2
Photoelectric Sensors E3F2 Threaded Cylindrical Photoelectric Sensors with Built-in Amplifier for Use as an Optical Proximity Switch M18 DIN-sized cylindrical housing Housing materials: plastic, nickel
K10 Intrinsically Safe Electro-Pneumatic Positioner Operating Manual
K0 Intrinsically Safe Electro-Pneumatic Positioner Operating Manual Pneumatic Connection Single Acting Actuator (Spring Return): For single acting actuators Outlet Port 2 is to be plugged. Outlet Port
Features. Sensing range 50 mm mm... Type of light. Light source 3) Wave length. Adjustment 2) PL80A.
-3-3 Detailed technical data Features WT18-3 WT18-3 Ex WL18-3 WL18-3 Ex WS/WE18-3 Reliable object detection for demanding applications Sensor principle Photoelectric proximity sensor Through-beam photoelectric
SLIMBAT2 wireless photocell MANUAL
v.1.1 1. of the device The wireless photocell is a safety element in gate automation. Between the transmitter and the receiver, the infrared beam is created, forming invisible to the human eye barrier.