INSTALL INSTRUCTIONS RSXMR-9886-P-48
|
|
- Cornelia Hudson
- 5 years ago
- Views:
Transcription
1 INSTALL INSTRUCTIONS RSXMR-9886-P-48 Installation Instructions RSXMR-9886-P-48 (CEQ )
2
3 INSTALL INSTRUCTIONS RSXMR-9886-P-48 Contents Section Description Page 1 Copyright Disclaimer Warnings 2 2 Introduction 3 3 OVP Package Contents Prerequisites Tools 3 4. OVP Definitions Bracket Installation Port Definitions PRIOR TO Cable Installation 5 7 Installing Ground Cable 6 8 Installing Alarm Cable 6 9 Installing DC IN Cables 7 10 Installing DC OUT Cables 7 11 Closing and Securing Unit 8 Page 1 of 8
4 RSXMR-9886-P-48 INSTALL INSTRUCTIONS 1.0 Copyright Raycap, Inc All Rights Reserved 1.1 Disclaimer The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Raycap customers only for the purposes of the agreement under which the document is submitted, and no part may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Raycap. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Raycap welcomes customer comments as part of the process of continuous development and improvement of the documentation. Raycap has made all reasonable efforts to ensure that the instructions contained in this document are adequate and free of material errors and omissions. Raycap will, if deemed necessary explain issues which may not be covered by this document. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Raycap shall have no liability for any error damage of any kind resulting from the use of this document. 1.2 Warnings Please read this manual prior to use to become familiar with the product s numerous features and operating procedures. To maintain the maximum degree of safety, follow the sequences as outlined. Before using the product, read all instructions and cautionary markings on the product and on any equipment connected to the product. CAUTION Unless otherwise noted, product usage that is not recommended or sold by the product manufacturer can result in risk of fire, electric shock, or injury to persons. CAUTION Do not operate the product if it has been damaged in any way. Return damaged products to their manufacturer for repair or replacement. CAUTION Do not disassemble the product as incorrect reassembling can risk electrical shock or fire. WARNING Disconnect or disable the DC power source to the product prior to beginning its installation. Ensure that the DC power source to the product remains de-energized until the completion of the installation and after all connections have been verified to be correctly configured. For conditions other than those described above, please contact a Raycap Account Representative at (208) , (800) or Thank you for choosing quality products from Raycap. Page 2 of 8
5 INSTALL INSTRUCTIONS RSXMR-9886-P Introduction Radio to the RRH is provided through copper cables traveling from the base station to the top of the tower or roof top. This creates a conductive path, making the active equipment at the top and the base of the site vulnerable to damage by direct lightning strikes. Protection systems must be able to withstand direct lightning currents in order to protect the sensitive equipment. Raycap s RRH solutions featuring Strikesorb SPD technology significantly enhance the reliability & availability of the RRH site by providing superior electrical protection. 3.0 OVP Package Contents 2 each Enclosure with mounting bracket Crimp-on male barrel connectors (18-22AWG) 3.1 Prerequisites This Document describes how to install the RSXMR-9886-P-48 on-site. Installers of Raycap s RRH surge protective and fiber/power management solutions must be industry professionals who have attended training on the proper installation of the equipment by Raycap and/or the mobile operator. Installers are required to read this installation guide thoroughly prior to installation of the Raycap RRH protection equipment. 3.2 Tools #1 Flat blade screwdriver #1 Philips screw driver Jewelers flate blade screwdriver (for alarm installation) Crimping tool 3/8" wrench Drill Drill bits that are the exact size of each cable to be installed Cable stripping tool Page 3 of 8
6 RSXMR-9886-P-48 INSTALL INSTRUCTIONS OVP Definitions 4. Mounting Hole (4 Places) ø 0.25 [6.4] 5.51 [140] Mechanical Lug 2-14 AWG 4.33 [110] Alarm Connectors 12 to 22 AWG Bracket Installation 1 each clamping range [4.5-10] 5.1 For POLE mounting: Using a stainless steel banding 2 each strap, clamping attach range mounting bracket to pole per [19-28] AT&T specifications. Note: All cable glands are provided with solid plug to be customized by customer For WALL mounting: Attach mounting bracket to wall inch [mm] using 2 holes shown. 3 each clamping range [7-13] 5.2 Secure bracket to unit by connecting with 4 screws and nuts as shown using Philips screwdriver and 3/8 wrench. Page 4 of 8
7 INSTALL INSTRUCTIONS RSXMR-9886-P-48 Port Definitions 6.1 See illustration to identify Base Port Assembly Definitions. PRIOR TO Cable Installation DC IN Alarm Ground DC OUT Note: If unit is to be installed outdoors, all cables MUST be outdoor rated. 6.2 Identify and match cable to appropriate gland port. (Example: Ground cable to Ground Port) Read each section below for individual installation procedure PRIOR to drilling: Installing Ground Cable (Section 7.1, page 6) Installing Alarm Cable (Section 8.1, page 6) Installing DC IN Cables (Section 9.1, page 7) Installing DC OUT Cables (Section 10.1, page 7) 2½" Max Drill Depth 2½" 2" Before Drilling: 1. Match drill bit size to cable size. Drill bit should not exceed 2½" in length. This will prevent protential damage to the internal components. 2. Using a sharp drill bit, drill through rubber insert. Insert should be installed with nut tightened when drilling to ensure proper hole location and to keep insert stable while drilling. Note: Measure Twice, Drill Once! Remove gland nut to lessen pressure against rubber insert, pull cable through gland nut and then through rubber insert hole, then tighten. Page 5 of 8
8 RSXMR-9886-P-48 INSTALL INSTRUCTIONS Installing Ground Cable 7.1 Drill hole in ground port rubber insert. Be sure drill bit diameter matches diameter of ground cable. Note: See 6.1 and 6.2 for Port Definitions and Drilling. 7.2 Feed ground cable through gland nut and ground port. Connect to ground lug as shown. 7.3 Tighten gland nut to create proper seal around ground cable. Installing Alarm Cable 8.1 Drill hole in alarm port rubber insert. Be sure drill bit diameter matches diameter of alarm cable. Note: See 6.1 and 6.2 for Port Definitions and Drilling. 8.2 Feed alarm cable through gland nut and alarm port. 8.3 Connect alarm cable to alarm lugs according to the AT&T established color guide and Contact Points (NC, C, NO). 8.4 Tighten gland nut to create proper seal around cable. Page 6 of 8
9 INSTALL INSTRUCTIONS RSXMR-9886-P-48 Installing DC IN Cables 9.1 Drill hole in DC IN port rubber insert. Be sure drill bit diameter matches diameter DC IN cables. Note: See 6.1 and 6.2 for Port Definitions and Drilling. 9.2 Feed DC IN cables through gland nut and DC IN port. 9.3 Connect Supply (-48V) and Return cables to lugs according to the AT&T established color guide. Red: Supply (-48V) Black: Return 9.4 Tighten gland nut to create proper seal around DC IN cables. Installing DC OUT Cables 10.1 Drill hole in DC OUT port rubber insert. Be sure drill bit diameter matches diameter DC OUT cables. Note: See 6.1 and 6.2 for Port Definitions and Drilling Feed DC OUT cables through gland nut and DC OUT port Strip cables and insert into the provided RED male barrel connectors then crimp to secure to DC jumper cable. Supply (-48V) Return 10.4 Connect Supply (-48V) and Return by working the connectors into the pre-installed female BLUE barrel connectors Tighten gland nut to create proper seal around DC OUT cables. Page 7 of 8
10 RSXMR-9886-P-48 INSTALL INSTRUCTIONS Closing and Securing Unit 11.1 Close cover tightening and secure the four screws on the front of unit Installation complete. Page 8 of 8
11
12 RSXMR-9886-P-48 INSTALL INSTRUCTIONS
Installation Instructions Revision 1.0 June 2009 Page 1 of 6
Bulletin II 103282-EN Installation Instructions Revision 1.0 June 2009 Page 1 of 6 OneBase Dual Band and Twin TMA ETT19V2S12UB/ETW200VS12UB/ETW190VS12UB INTRODUCTION Andrew OneBase Tower Mounted Amplifiers
More informationBreezeMAX Wi² and BreezeACCESS Wi² Quick Installation Guide
This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the BreezeMAX Wi² and BreezeACCESS Wi² System Manual. Wi² Package Content Check
More informationInstalling the Camera
CHAPTER 2 This chapter provides information and instructions for installing the Cisco Video Surveillance PTZ IP camera, and includes the following topics: Installation Guidelines, page 2-1 Warnings Before
More informationChameleon Stand-alone
Quick Installation Guide Installation and Commissioning Chameleon Stand-alone Power Supply Module, 48 VDC, 650W, HE, IP65 Low Power Outdoor Applications 356849.03 Introduction Warnings..., page 3 Tools
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More informationInstalling and Cabling Flexi Zone Micro High Power 2x20 W BTS DN Issue 02 Approval Date yyyy-mm-dd
Nokia Networks Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS DN09229011 Issue 02 Approval Date yyyy-mm-dd Installing and Cabling Flexi Zone Micro High Power The information in this document
More informationInstallation Notes TII Model 341 Protector
Installation Notes TII Model 341 Protector (ATT-IS PEC 32918) for MERLIN Communications System In Range Out of Building (IROB) Station Installation By Trained Technician Only WARNING: Failure to follow
More information60W Power over Ethernet Waterproof Adapter PoE IEEE BT Single Port Injector for Outdoor Application
WWW.PHIHONG.COM 60W Power over Ethernet Waterproof Adapter PoE IEEE BT Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3bt Standard Non-Vented Case with Mounting Bracket
More informationMounting on the Ceiling Using Flush Mount (Face Down)
Mounting on the Ceiling Using Flush Mount (Face Down) Installation Guide 2014/02/14 Table of Contents Safety Information... 3 Installation Procedures... 5 Step 1: Drill a Hole on the Ceiling... 5 Step
More informationSUN KTL-USH0 Quick Guide. Issue: 01 Part Number: Date: HUAWEI TECHNOLOGIES CO., LTD.
SUN2000-100KTL-USH0 Quick Guide Issue: 01 Part Number: 31509347 Date: 2018-02-08 HUAWEI TECHNOLOGIES CO., LTD. NOTICE The information in this document is subject to change without notice. Every effort
More informationWarning Before Installation. Package Contents EN - 1. Refer to your user's manual for the operating temperature.
510000221G Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or
More informationEN - 1. Warning Before Installation. Package Contents. Refer to your user s manual for the operating temperature.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny objects
More informationModel 2380 Rack-Mount Kit
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.tek.com/keithley Model 2380 Rack-Mount Kit Installation Instructions Introduction The Model 2380 Fixed Rack-Mount
More informationM215 (M215-60) Safety
M215 QUICK INSTALL GUIDE M215 (M215-60) Safety Important Safety Information This document contains important instructions to use during installation and maintenance of the Enphase M215 Microinverter. To
More informationMBE Mounts and Adapters
MBE Mounts and Adapters MBE Series en Installation Guide MBE Mounts and Adapters Table of Contents en 3 Table of Contents 1 Important safety instructions 4 2 MBE Series Mounts and Adapters 6 2.1 Unpacking
More informationCisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2
Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2 Cisco CRS 3-Phase AC Power Distribution Unit 2 Revised: November 18, 2016,
More informationEnphase S-Series Microinverter and Engage Cable Safety
SAFETY Enphase S-Series Microinverter and Engage Cable Safety Important Safety Information (S280-60-LL and S230-60-LL) This document contains important instructions to use during installation of the Enphase
More informationHX WCS Indoor DAS Remote Unit Quick Installation Sheet
HX WCS Indoor DAS Remote Unit Quick Installation Sheet CMA-447-AEN GENERAL INFORMATION 1. The HX WCS remote is an upgrade unit and is installed in conjunction with an existing HX and/or MA1000/ MA2000
More informationCambium PTP 650 LPU and Grounding Kit Installation Guide
Cambium PTP 650 LPU and Grounding Kit Installation Guide Accuracy While reasonable efforts have been made to assure the accuracy of this document, Cambium Networks assumes no liability resulting from any
More informationConnecting Power and Ground
This chapter explains how to connect the power and ground for NCS 2006 shelf. The sections are: Power and Ground Description, page 1 NTP-L12 Installing Power and Ground to the NCS 2006 Shelf, page 2 Power
More informationTerragraph Installation Guide. March 8, 2017 Version 0.3
Terragraph Installation Guide March 8, 2017 Version 0.3 Warnings WARNING: Shock Hazard. May result in serious injury or death. Turn off circuit power at circuit breaker or disconnect power at source receptacle
More informationR1 Extender. Quick Installation Guide
R1 Extender Quick Installation Guide V1.0 January 2009 Copyright Copyright 2008 all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into
More informationR2 Extender. Quick Installation Guide
R2 Extender Quick Installation Guide V 2.1.9 October 2009 Chapter 1 Introduction Page 1 Copyright Copyright 2009 all rights reserved. No part of this publication may be reproduced, adapted, stored in a
More informationWarning Before Installation
Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Contact your distributor in the
More informationWarning Before Installation. Package Contents EN-1. Power off the Network Camera as soon as smoke or unusual odors are detected.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny objects
More informationRuckus Wireless ZoneFlex 7762 Dual Band n Outdoor Access Point. Installation Guide
Ruckus Wireless ZoneFlex 7762 Dual Band 802.11n Outdoor Access Point Installation Guide Part Number 800-70216-001 (Revision H) Published November 2011 www.ruckuswireless.com Contents 1 About This Installation
More informationModel 2380 Rack-Mount Kit
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.tek.com/keithley Model 2380 Rack-Mount Kit Installation Instructions Introduction The Model 2380 Fixed Rack-Mount
More informationInstallation Guide V290 (Color) This guide provides basic information for Unitronics LCD color touchscreen models V C30B and V T40B.
Vision OPLC Installation Guide V290 (Color) This guide provides basic information for Unitronics LCD color touchscreen models V290-19-C30B and V290-19-T40B. General Description Vision OPLCs are programmable
More informationModel#: IN-DO3MIRF 3MP Outdoor Dome with True Day/Night, IR, Basic WDR, Fixed lens
Model#: IN-DO3MIRF 3MP Outdoor Dome with True Day/Night, IR, Basic WDR, Fixed lens Hardware User Manual (PoE) 2013/03/06 Table of Contents Precautions... 3 Introduction... 4 Package Contents... 4 Safety
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationDC Outdoor Power Supply/Chargers
DC Outdoor Power Supply/Chargers Installation Guide Models Include: WayPoint3 WayPoint7-2.5A @ 12VDC or 24VDC. - 6A @ 12VDC or 24VDC. - 115/230VAC input. - 115VAC input. WayPoint5 WayPoint7V - 4A @ 12VDC
More informationRelease Notes. Electrostatic Discharge and Grounding Guide for Cisco NCS 2000 Series. Prerequisites. Preparing Your Location
First Published: 2017-01-31 Text Part Number: Electrostatic Discharge and Grounding Guide for Cisco NCS 2000 Series Prerequisites This document uses illustrations to explain the workflow that we recommend
More informationMODEL 8000MP LEVEL SENSOR
1 MODEL 8000MP LEVEL SENSOR INSTRUCTIONS FOR INSTALLATION, OPERATION & MAINTENANCE VISIT OUR WEBSITE SIGMACONTROLS.COM 2 SERIES 8000MP LEVEL SENSOR 1. DESCRIPTION The Model 8000MP Submersible Level Sensor
More informationSecondary Surge Arrester Instruction Manual Page 1 of 5
Secondary Surge Arrester Instruction Manual Page 1 of 5 GENERAL SAFETY INSTRUCTIONS WARNING: ARRESTER CAN FAIL VIOLENTLY AND CAUSE INJURY AND PROPERTY DAMAGE WHEN APPLIED AT VOLTAGES GREATER THAN 120V.
More informationR2 BaseStation. Quick Installation Guide
R2 BaseStation Quick Installation Guide V 1.0 March 2009 Page 1 Copyright Copyright 2009 all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated
More informationAlphaGateway SMG-01PE Quick Start Guide
AlphaGateway SMG-01PE Quick Start Guide 9 Power-Passing Tap 2 AlphaGateway SMG 5 1 8 6 3 4 7 PoE Devices Security Camera Wi-Fi Radio 1. 1 RF Connector Test Port A -20dB test port allowing measurement of
More informationInstruction / Installation Sheet DataComm Electronics WH Recessed Pro-Power Kit with Duplex Receptacle and Straight Blade Inlet
Instruction / Installation Sheet DataComm Electronics 45-0024-WH Recessed Pro-Power Kit with Duplex Receptacle and Straight Blade Inlet DataComm Electronics, Inc. 6349 Peachtree Street Norcross, GA 30071-1725
More informationQuick Start Guide. Preparation. Installation. Operation. Support. Vaisala NOMAD 3 Data Logger. Online manuals
Quick Start Guide www.vaisala.com Vaisala NOMAD 3 Data Logger Preparation Package Contents Plan Instrumentation Create a SkyServe Account Activating the Nomad 3 Nomad 3 Toolbox Create Setup Files 2 4 5
More informationCanopy Surge Suppressor
Canopy Surge Suppressor User Manual 300SS-UG-E R 02 02 2002 Motorola, Inc. All rights reserved. Printed in the U.S.A Notices Safety Precautions: Before beginning with your installation, please read and
More information21 TRACK MAINTENANCE GUIDE
Mountain Engineering II, Inc. 21 TRACK MAINTENANCE GUIDE 1233 Sherman Drive, Longmont, CO 80501-6133 303-651-0277 303-651-6371 (fax) www.mountainengineering.com Table of contents Table of contents...2
More informationPower Supply and Fan Module Installation
3 CHAPTER This chapter describes how to remove and install a new or replacement power supply or fan module in a Catalyst 3750-E or Catalyst 3560-E switch. See these sections: Installation Overview, page
More informationM250 (M LL) Safety
M250 SAFETY M250 (M250-60-2LL) Safety Important Safety Information This document contains important instructions to use during installation of the Enphase M250 Microinverter. To reduce the risk of electrical
More informationPN PSTK-120 PowerSwitch Tail 120vac Kit PN PSTK-240 PowerSwitch Tail 240vac Kit
CAUTION: Please make sure you have or have access to the skills necessary to assemble and use this product. Always secure the case with the included screws before applying electrical power to the power
More informationINSTALLATION INSTRUCTIONS
Wired Remote Controller 7 Day Programmable Ductless Systems KSACN0401AAA (High Wall Models) KSACN0501AAA (Ducted/Cassette Models) INSTALLATION INSTRUCTIONS NOTE: Read the entire instruction manual before
More informationNavigator II INstallatIoN MaNUal For static and PaN/tIlt configurations
Navigator II Installation MANUAL For Static and Pan/Tilt Configurations Document Number: 432-0001-00-12, rev 100 FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole
More informationAssembly and Setup Manual
M-12 Series Copyboard / C-12 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-12 series Copyboard and C-12 series Captureboard. (The copyboard and/or
More informationWarning Before Installation. Package Contents EN - 1. Refer to your user s manual for the operating temperature.
5000020G Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny
More informationNASDAQ: TESS. Verizon Wireless. Commscope Hybrid BOM
NASDAQ: TESS Verizon Wireless Commscope Hybrid BOM VZW HELIAX FiberFeed Trunk Cables FiberFeed trunk cable assemblies are factory constructed specifically for the devices listed in the Commscope guide
More informationOSRAM ReliaSys TM D15 LED Retrofit Kit INSTALLATION GUIDE
www.osram-americas.com S90655 OSRAM ReliaSys TM D15 LED Retrofit Kit INSTALLATION GUIDE OSRAM ReliaSys TM Outdoor LED Retrofit Kit is an alternative to high-intensity discharge (HID) lamps up to 400W (MH)
More informationSECTION N -- ELECTROSTATIC DISCHARGE (ESD)
INSTALLATION REQUIREMENTS AT&T January, 2012 Section N, ATT-TP-76300 Revised NA SECTION N -- ELECTROSTATIC DISCHARGE (ESD) CONTENTS PAGE 1. GENERAL... N-1 1.1. Introduction... N-1 1.2. General Requirements...
More informationVerizon Wiring Manual PowerShift. 10 January 2018
Verizon Wiring Manual PowerShift 10 January 2018 1. General DISCLAIMER: This document has been developed by CommScope, and is intended for the use of its customers and customer support personnel. The information
More informationRMB-3 Peripheral Unit. Installation Guide INSTALLATION GUIDE WESTELL.COM. Westell Technologies Part # Rev. A
RMB-3 Peripheral Unit Installation Guide INSTALLATION GUIDE Westell Technologies Part # 030-300812 Rev. A Copyright 2017 by Westell Technologies. All Rights Reserved. The material discussed in this publication
More informationSpeed Dome Installation Manual
Speed Dome Installation Manual Version 1.0.2. Revised October 30 th, 2018 Contents Welcome... 3 Important Safeguards and Warnings... 3 1 INSTALLATION PREPARATION... 5 1.1 Basic Requirements... 5 1.2 Installation
More informationE2EC. High-sensitivity DC 2-Wire Sensors and Subminiature Sensors with Long-distance Detection. Cable Amplifier Proximity Sensor. Ordering Information
Cable Amplifier Proximity Sensor EEC CSM_EEC_DS_E High-sensitivity DC -Wire Sensors and Subminiature Sensors with Long-distance Detection Shielded Sensor Heads from -mm to M diameters that can be embedded
More informationTraceTek Leak Detection Master Module Installation Instructions TOOLS REQUIRED STORAGE
TTDM-128 TraceTek Leak Detection Master Module Installation Instructions TRACETEK APPROVALS AND CERTIFICATIONS TYPE NM General Signaling Equipment 76LJ GENERAL INFORMATION Please read these instructions
More informationRMB Peripheral Units Installation Guide
RMB Peripheral Units Installation Guide Part Number 65-000101 2011 by Kentrox, Inc. All rights reserved. Copyright 2011 by Kentrox, Inc. All Rights Reserved. The material discussed in this publication
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationFDMA MARINE SURGE PROTECTIVE DEVICE
FDMA MARINE SURGE PROTECTIVE DEVICE FRY YOUR FISH NOT YOUR ELECTRONICS! Protect your costly GPS, Depth Finder and Fish Finder Introducing the FDMA-212HW and FDMA- 224HW, our new first line of defense for
More informationMASTERLINE Ultimate Hybrid High Voltage 4/12 (MLUH HV 4/12) blunt cut at BTS side
INSTALLATION MANUAL HUBER+SUHNER AG Fiber Optics MASTERLINE Ultimate Hybrid High Voltage 4/12 (MLU HV 4/12) blunt cut at BTS side DOC-0000803885 Rev A June 18, 2018 Page 1 of 12 (MLUH HV 4/12) blunt cut
More informationLARGE S URGE-PROTECTOR S HELTER
LARGE S URGE-PROTECTOR S HELTER The weather-resistant Large Surge-Protector Shelter (simply referred to as the shelter in this manual) provides protection from the elements for Surge Protectors (not included)
More informationRUFIS. Remote Radio Head (RRH) Unit Field Installation System. Ease your transition towards next generation base stations
Remote Radio Head (RRH) Unit Field Installation System Ease your transition towards next generation base stations Introduction Remote Radio Heads improve efficiency of next generation wireless base stations
More informationInstruction Manual: IM E
Innovative Technology TVSS Products The I.T. Equalizer Installation Instruction Manual: IM01005011E Rev. 2 May 2009 Contents Page 1 Introduction... 1 1.1 Scope... 1 1.2 I.T. Equalizer Catalog Numbering
More informationM215 Safety (M LL-S22-IG / S23-IG / S24-IG)
M215 SAFETY M215 Safety (M215-60-2LL-S22-IG / S23-IG / S24-IG) Important Safety Information This document contains important instructions to use during installation of the Enphase M215 Microinverter. To
More informationCLS Atmosphere LED-panel
INDEX Index 2 Introduction Included items Optional accessories Safety information 4 Installation REVO Colour Flow 5 LDC connectioncable for the REVO Colour Flow 6 Assemble a REVO Colour Flow connectioncable
More informationALTAI C1N SUPER WIFI CPE INSTALLATION GUIDE. Version 1.0 Date: September, Altai Technologies Ltd. All rights reserved
ALTAI C1N SUPER WIFI CPE INSTALLATION GUIDE Version 1.0 Date: September, 2013 Copyright 2007 Altai Technologies Limited ALL RIGHTS RESERVED. Altai Technologies Limited Unit 209, 2/F, East Wing, Building
More informationINSTRUCTIONS FOR THE INSTALLATION OF THE INFINITY "L" DISPLAY HOOD (INTO PREVIOUSLY INSTALLED INFINITY "L" SYSTEMS)
Doc. 6001025 Rev B INSTRUCTIONS FOR THE INSTALLATION OF THE INFINITY "L" DISPLAY HOOD (INTO PREVIOUSLY INSTALLED INFINITY "L" SYSTEMS) Rev. B Doc. 6001025 Page 1 of 13 IMPORTANT NOTICE This document covers
More informationTower Company, Inc. IM1.00MVU (REV.B) 1639 Old Dixie Highway P.O. Box Vero Beach, FL USA Voice (772) Fax (772)
PAGE 1 OF 8 MOBILE VAN UNIT TRACK-CARRIAGE ASSEMBLY INSTALLATION AND TOWER SET-UP INSTRUCTIONS PAGE 2 OF 8 W A R DANGER I N G WARNING NOTICE DANGER!!! W A R DANGER I N G DO NOT CLIMB! DEATH MAY OCCUR!
More informationRE.41.LGTW - L-gateway - Modular IoT Base Station Quick Installation Guide
RE.41.LGTW - L-gateway - Modular IoT Base Station Quick Installation Guide Author Ivo van Ling Hardware Release 1.0 Quick Install Guide Version QIG_L-gateway_v1.20 Date 29-08-2016 Covering Product code
More informationMODEL SST3-MV INSTALLATION INSTRUCTIONS FOR FEDERAL MODEL SST3-MV SELECTABLE SIRENTONE-MULTI VOLT
MODEL INSTALLATION INSTRUCTIONS FOR FEDERAL MODEL SELECTABLE SIRENTONE-MULTI VOLT INSTALLATION INSTRUCTIONS FOR FEDERAL MODEL SELECTABLE SIRENTONE-MULTI VOLT A. GENERAL. The Federal Model is a solid-state
More informationInstallation Guide V290 (Color) This guide provides basic information for Unitronics LCD color touchscreen models V C30B and V T40B.
Vision OPLC Installation Guide V290 (Color) This guide provides basic information for Unitronics LCD color touchscreen models V290-19-C30B and V290-19-T40B. General Description Vision OPLCs are programmable
More informationVRp Three-Phase Precision AC Voltage Regulator
VRp-22500-0338 Three-Phase Precision AC Voltage Regulator INSTALLATION INSTRUCTIONS Inspection and Unpacking Please inspect the wooden crate for obvious shipping damage. Some crates contain up to six (6)
More informationConnect the drop cable to the ODU (PSU port) and LPU
Installing the copper Cat5e Ethernet interface 2 Fit the parts into the body and lightly screw on the gland nut (do not tighten it): Connect the drop cable to the ODU (PSU port) and LPU 1 (a) Plug the
More informationQuick Start Guide and Important Safeguards
NETWORK CAMERA Model: IK-WB80A Quick Start Guide and Important Safeguards This guide describes the hardware installation. Refer to the user's manual (PDF file) contained in the CD-ROM for settings, operations
More informationINSTALLATION MANUAL FOR BISOL SOLAR MODULES
INSTALLATION MANUAL FOR BISOL SOLAR MODULES Before start of installation of BISOL solar modules, carefully read this installation manual in whole. This manual contains important information on safety,
More informationFlat Surfaced Ceiling Mounted Exterior Dome (Face Down) IN-DO2MIRVSLL, IN-DO4MF, IN-DO4M36A, IN-DO1MIRF, IN-DO2MIRF,
Outdoor Dome Flat Surfaced Ceiling Mounted Exterior Dome (Face Down) Installation Guide For Models: IN-DO2MIRVSLL, IN-DO4MF, IN-DO4M36A, IN-DO1MIRF, IN-DO2MIRF, IN-DO3MIRF, IN-DO5MIRF, IN-DO1MIRV, IN-DO2MIRV,
More informationInstallation manual EVA Start and Protected
Installation manual EVA Start and Protected 1 Introduction This document shows how to install and use the charge station EVA. There are three families of EVA models: EVA Connected, EVA Protected and EVA
More informationSiemens Drives & PLCs
Automation System S7-300: Getting Started CPU 31xC: Commissioning Introduction 1 Preparation 2 SIMATIC S7-300 Automation System S7-300: Getting Started CPU 31xC: Commissioning Learning units 3 Further
More informationPAR+ & MSC+ Controller. Installation Manual
PAR+ & MSC+ Controller Installation Manual Contents Introduction... 1 System Configuration...1 Parts List and Tools Required for Installation...1 Installation Checklist...1 Mount Controller Pedestal on
More informationQuick Installation Guide
FD8372 Fixed Dome Network Camera Quick Installation Guide English 繁中簡中日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska 5MP Full HD Smart Focus System Warning Before Installation
More informationSeries Amp Pad Mount Quick Connect Input and Output Power Panels
Series 300 2000-4000 Amp Pad Mount Quick Connect Input and Output Power Panels DANGER is used in this manual to warn of a hazard situation which, if not avoided, will result in death or serious injury.
More informationVision OPLC. General Description. Standard Kit Contents. Installation Guide Vision120. This guide provides basic information for Unitronics Vision120.
Vision OPLC Installation Guide Vision120 This guide provides basic information for Unitronics Vision120. General Description V120 OPLCs are micro-oplcs, rugged programmable logic controllers that comprise
More informationThis guide provides basic information for Unitronics Models 230/260/280/290 (Non-color Screens).
Vision OPLC Installation Guide Models 230/260/280/290 (Non-color Screens) This guide provides basic information for Unitronics Models 230/260/280/290 (Non-color Screens). General Description Vision OPLCs
More informationInstalling the Interface Line Card in the Cisco cbr Chassis 6
Installing the Interface Line and PIC Cards in the Cisco cbr Chassis Installing the Interface Line and PIC Cards 2 Installing PICs in the Cisco cbr Chassis 2 Installing the Interface Line Card in the Cisco
More informationStandard Strip Series
Standard Strip Series Standard Strip STS-12 LED Lighting Systems Installation Manual (Version 1.3) YESCO LLC, 5119 South Cameron Street, Las Vegas, NV 89118 Table of Contents Introduction 1 Mounting Diagrams
More informationInstallation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120-O
Release 3.0 NN47251-312 Issue 02.01 June 2014 Installation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120-O How to get help To access the complete range of services and support that Avaya provides,
More informationWall-Mounting your HP TouchSmart. User Guide
Wall-Mounting your HP TouchSmart User Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein
More informationNetCommWireless. Quick Start Guide NTC-30 Series - Outdoor WiFi Router
NetCommWireless Quick Start Guide NTC-30 Series - Outdoor WiFi Router NetCommWireless Let s get this show on the road You must be excited to get started with your Outdoor WiFi Router. If all goes to plan,
More informationHP R/T2200 UPS. Overview. Precautions. Installation Instructions. The HP UPS R/T2200 features power protection for loads up to 2200 VA/1600 W.
HP R/T2200 UPS Installation Instructions Overview The HP UPS R/T2200 features power protection for loads up to 2200 VA/1600 W. For more information about any of the topics covered in this document, see
More informationFE8171V. 3MP 360 Panoramic View Vandal-proof
FE8171V 3MP 360 Panoramic View Vandal-proof Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating
More informationAutoScan to MultiScan Replacement Kit
Instruction Sheet P/N AutoScan to MultiScan Replacement Kit WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other
More informationCHANNEL LETTER LIGHTING UNIQUE LIGHTING SOLUTIONS RETROFIT INSTALLATION GUIDE
UNIQUE LIGHTING SOLUTIONS LIGHTING WARNING -Installation must only be performed by a licensed electrician. -To prevent death, injury or damage to property this product must be installed in accordance to
More informationAW58100HTP-PAIR USER S MANUAL
USER S MANUAL 5.8 GHz Outdoor 100 Mbps Ethernet Point-to-Point Radio System Industrial-grade, long-range wireless Ethernet systems AvaLAN W I R E L E S S The AW58100HTP-PAIR consists of two AW58100HTS
More informationInstalling the Cisco 2524 and Cisco 2525 Routers
CHAPTER 3 Installing the Cisco 2524 and Cisco 2525 Routers This chapter guides you through the installation of the Cisco 2524 and Cisco 2525 routers and includes the following sections: Required Tools
More informationHP UPS R/T3000 ERM. Overview. Precautions. Installation Instructions
HP UPS R/T3000 ERM Installation Instructions Overview The ERM consists of two battery packs in a 2U chassis. The ERM connects directly to a UPS R/T3000 or to another ERM. Up to two ERM units can be connected.
More informationTotal Protection Solutions Surge Protective Devices SurgeTrack Series: 080, 120, 160, 240, 300 and 400
Total Protection Solutions SurgeTrack Series: 080, 120, 160, 240, 300 and 400 Surge Protective Devices Installation, Operation and Maintenance Manual SURGETRACK INSTALLATION, OPERATION AND MAINTENANCE
More informationCompact Medium SOLARLOK Junction Box. Application Specification
Application Specification 114-106003 10OCT. 2010 Rev. A2 Compact Medium SOLARLOK Junction Box Application Specification CONTENT 1. Introduction...2 2. Supporting Documents...2 2.1 Drawings...3 2.2 Product
More informationPerle MCR200 Installation Guide
Perle MCR200 Installation Guide P/N 5500322-10 Introduction The Perle MCR200 Chassis is a 2 slot chassis able to accommodate up to 2 Perle Media Converter modules or 1 Media Converter Module and an MCR-MGT
More information33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3at Standard -40 to +60 C Temperature Range Diagnostic LEDs Full Protection
More informationSUN2000-(2KTL-5KTL)-L0. Quick Guide. Issue: 01 Part Number: Date: HUAWEI TECHNOLOGIES CO., LTD.
SUN2000-(2KTL-5KTL)-L0 Quick Guide Issue: 01 Part Number: 31509986 Date: 2018-09-05 HUAWEI TECHNOLOGIES CO., LTD. 0 NOTICE 1. The information in this document is subject to change without notice. Every
More informationReview of Generic Requirements for Remote Radio Head Protection Used in Fiber to the Antenna (FTTA) Systems GR-3177-CORE Issue 1, December 2014
Review of Generic Requirements for Remote Radio Head Protection Used in Fiber to the Antenna (FTTA) Systems GR-3177-CORE Issue 1, December 2014 Telcordia Contact: Ernie Gallo Director Telcordia Network
More information