Privacy Wall - Power & Data Box (Field Installed) Modular & Hardwire Versions
|
|
- Octavia Arnold
- 5 years ago
- Views:
Transcription
1 Privacy Wall - Power & Data Box (Field Installed) Modular & Hardwire Versions If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE ( ) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: ) Or visit our website: Steelcase Inc. Grand Rapids, MI U.S.A. Printed in U.S.A. NOTE: Unused modular electrical connector openings are not required to be capped. Page 1 of 15
2 Tools Table of Contents ELECTRIC SHEARS 2" WIDE MASKING TAPE Topic Determining the Opening 3 Page Removing the Skin 4-5 Removing the Acoustic Core Material 6 Installing Power 7 Installing the Modular Version 8 Mounting a Base Power Block 9 Chicago & New York City Hardwire Box and Bracket Assembly Wiring Schematics 15 RAYBO FLOOR COVERING -WET/DRY- VAC Page 2 of 15
3 1b 6-3/8" 2 Determining the Opening 1. Find the center of the panel (1a) and mark the width of the opening. Determine the height you want the opening from the bottom of the panel and mark the height of the opening (1b). Use a straight edge to connect your marks (1c). 2. The size of the opening. 28-1/2" (DESK HT.) 16-1/8" (ADA HT.) BOTTOM OF SKIN 4" C L 8" 1a C L OF PANEL 1c Page 3 of 15
4 1 2b Removing the Skin 1. Masking tape is applied to protect surrounding surface material. NOTE: Tape should not be applied to wall for more than 1 hour. 2. For fabric and/or vinyl panel, cut the perimeter out with a utility knife (2a, b & c). TIP: Place cardboard around opening to protect outside surface from getting dirt or damage while using tools. 2a 2c Page 4 of 15
5 4 Removing the Skin (cont.) 3. Drill all four (4) holes slightly offset from the corners to help provide for a sharp 90 corner. 4. Use electrical shears on all four (4) sides to remove panel covering. 3a 5. Use a utility knife on all four (4) sides to cut through the acoustical core and remove. 5 3b CAUTION: Make sure utility knife blade is not to long, to damage opposite face. Page 5 of 15
6 1 Removing the Acoustic Core Material 1. File down the edges. 2. Remove acoustical core material 3" left & right from the cut side ONLY. If installing a Chicago & New York City hardwire box, you will need to remove 5" from the bottom edge of the cut side opening also. 3" CAUTION: It is very important to remove this material slowly and thoroughly. If using a hammer to apply force to any type of chisel or spatula, make sure the force used is minimal otherwise damage to the panel surfaces may occur. 5" Chicago & New York City Only 2 3" Page 6 of 15
7 4a Installing Power 4b 1. Feed power harness through opening (1a) and send downward to base of panel (1b & 1c) or upward to ceiling channel. 1c 1a 1b Single sided block shown. Same for double sided block. 4. Secure the entire assembly to the frame with the mounting clips (4a) and screws (4b) provided. Six (6) clips required. TIP: This is a good time to install a pull string for data/communication wires. 2 3 Page 7 of 15
8 3a Installing the Modular Version 1. Remove masking tape from panel. 2. Attach the receptacles to the power block. Snap the spacer onto the junction box. Attach the appropriate communication receptacle into the spacer then snap the face plate adaptor into position. 3. Attach the receptacle faceplate over the receptacles (3a & b). 2 3b SPACER COMMUNICATION RECEPTACLE RECEPTACLES FACE PLATE ADAPTOR Page 8 of 15
9 Mounting a Base Power Block 1. Remove the top mounting tabs by bending backwards until they snap off. 2. Insert bottom tabs of power block into key slots of bottom rail. 3. Slide power block toward the smaller opening until you hear a snap sound. 2 HOLES IN TRACK WHICH TABS ON POWER BLOCK ARE INSERTED TOP MOUNTING TABS 3 1 THESE TWO TABS ARE LOCATED UNDERNEATH THE POWER BLOCK Page 9 of 15
10 2a MOUNTING TABS Chicago & New York City Hardwire Box and Bracket Assembly 1. Remove knockouts in box prior to installing in frame. 2b NOTE: Chicago & New York City power/communication to be applied to wall system prior to final installation of wall to ceiling grid for maximum flexibility. 2. Without extension covers, feed box into the hole of the frame, making sure mounting tabs are facing upward and towards you. KNOCKOUT 1 HARDWIRE BOX Page 10 of 15
11 Chicago & New York City Hardwire Box and Bracket Assembly (cont.) MOUNTING BRACKET 3. Pre bend mounting bracket at stitching (3a) with end flanges facing outwards. 3a STITCHING END FLANGES Page 11 of 15
12 Chicago & New York City Hardwire Box and Bracket Assembly (cont.) 4. Feed the bracket into the hole of the frame, with the top of bracket facing up. The hardwire box will have to be moved out of the way (downwards) while the bracket is inserted. 5. Mate hardwire box with mounting bracket. The bracket sandwiches the hardwire box (5a). Secure the box to the bracket with mounting screws (5b). 4 5b 5a Page 12 of 15
13 Chicago & New York City Hardwire Box and Bracket Assembly (cont.) 6. Attach conduit to the box. The hardwire box will have to be shifted to make your connections. For easier assembly, power in and power out the same side of the box. 7. Secure the entire assembly to the frame with the mounting clips (7a) and screws (7b) provided. Six (6) clips required. 7a 7b 6 Page 13 of 15
14 Chicago & New York City Hardwire Box and Bracket Assembly (cont.) 8. Attach receptacle extensions to hardwire egress opening. Go to page 8 to complete installation. Note: For proper fit of receptacle remove all ears on receptacle 8 9 Page 14 of 15
15 3+1 Powered by Separate Panels 3+1 Powered by Single Panel Line 1 (Black) Line 2 (Red) Line 3 (Blue) L1/L2/L3 Neutral (White) Systems Ground (Green) LINE 1 (Black) LINE 2 (Red) LINE 3 (Blue) LINE 4 (Pink) L1/L2/L3 Neutral (White) L4 Neutral (Gray) WIRING SCHEMATICS: Line 4 (Pink) L4 Neutral (Gray) Isolated Ground (Gn/Yl) Systems Ground (Green) Isolated Ground (Gn/Yl) NOTE: L-4 may be connected to P-1, P-2, or P-3. NOTE: L-4 should alternate between P-1, P-2, and P-3 to balance circuit loading. ELECTRICAL DATA: 2+2 Powered by Separate Panels 2+2 Powered by 3-Phase Single Panel 2+2 Powered by Split-Phase Panel 120 V 60 HZ 20 Amp USA & CANADA Wiring schematics must be followed to prevent overloading of the neutrals. Line 1 (Black) Line 2 (Red) L1/L2 Neutral (White) System Ground (Green) Line 1 (Black) Line 2 (Red) Line 3 (Blue) Line 4 (Pink) P-1 P-2 Line 1 (Black) Line 2 (Red) Line 3 (Blue) Line 4 (Pink) WARNING: Risk of Fire or Electric Shock: This office furnishing system may be connected to more than one source of supply. All sources must be disconnected prior to any servicing. No single circuit may be powered by more than one source. Line 3 (Blue) Line 4 (Pink) L3/L4 Neutral (Gray) Isolated Ground (Gn/Yl) NOTE: Line 3 or 4 should alternate between phases to balance circuit loading. L1/L2 Neutral (White) L3/L4 Neutral (Gray) System Ground (Green) Isolated Ground (Gn/Yl) NOTE: L-4 should alternate between P-1 and P-2 to balance circuit loading. L1/L2 Neutral (White) L3/L4 Neutral (Gray) System Ground (Green) Isolated Ground (Gn/Yl) 3 SepN Powered by Separate Panels 3 SepN Powered by Single Panel 3 SepN Powered by Split-Phase Panel Line 1 (Black) Line 2 (Red) L1 Neutral (White) L2 Neutral (Gray) Systems Ground (Green) Line 3 (Blue) L3 Neutral (White/Gray) Isolated Ground (Green/Yellow) Line 1 (Black) Line 2 (Red) Line 3 (Blue) L1 Neutral (White) L2 Neutral (Gray) L3 Neutral (White/Gray) Systems Ground (Green) Isolated Ground (Gn/Yl) P-1 P-2 Line 1 (Black) Line 2 (Red) Line 3 (Blue) L1 Neutral (White) L2 Neutral (Gray) L3 Neutral (White/Gray) Systems Ground (Green) Isolated Ground (Gn/Yl) Page 15 of 15
Answer Modular Power. Page 1 of Rev V. Power Kits. Change of Height Harness. Receptical Covers
Answer Modular Power Change of Height Harness Power Kits Receptical Covers NOTE: Unused modular electrical connector openings are not required to be capped. NOTE: The electrician can cut conduit and wire
More informationAvenir & kick Powerway
Avenir & kick Powerway System Flag Color -3-Circuit, Shared Neutral and System Ground (SHN) -4-Circuit, 3 with Shared Neutral and System Ground and 1- Isolated Circuit and Ground (3+D) (18" & 24" ONLY)
More informationV.I.A. - Monitor Shroud
V.I.A. - Monitor Shroud NOTE: Installing slatwall above a monitor shroud requires modification of the upper horizontal rail. See V.I.A. Slatwall assembly direction 939502328 for installation process. V.I.A.
More informationModular Table Power System Installation for Runner Non-folding Plug and Play Tables
Modular Table Power System Installation for Runner Non-folding Plug and Play Tables Topic General Safety Warnings Ganging Hardware Electrical Circuits Table of Contents Page End-to-End (Page 4) End-and-Back
More informationB Y R N E 8 - T R A C O V E R V I E W. 1) Introduction. 2) Universally Recognized. 3) Circuitry/Keying
Page 1 of 6 B Y R N E 8 - T R A C O V E R V I E W 1) Introduction Byrne Electrical Specialists, Inc. provides quality, cost effective, innovative power/data distribution solutions. From initial concept
More informationInstalling Simplex and Duplex Receptacles into: Series 9000 Structural Panel Series 9000 Energy Management Panel and Worksurface Avenir Power Panel
If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.322) for immediate action by people who want to help you. (Outside the U.S.A., Canada,
More informationPower/Data Instructions. Genius. Movable Walls. September
Power/Data Genius Movable Walls September 2011 Genius Movable Walls Power and Data in Shell Level 1 Conventional Boxes in Panel (conventional box and conduit) Choose 2x4 box or 4x4 box (shown). Separate
More informationVirtual PUCK for media:scape Kiosk and Answer
Virtual PUCK for media:scape Kiosk and Answer Note: For VP for media:scape on Kiosk, see page. For VP for media:scape on Answer, see page. # PHILLIPS /6" HEX DRIVE /6", /8" (all tables) plus 5/" (attached
More informationelectrics PRODUCT MAP / TABLE OF CONTENTS ELECTRICS & COMMUNICATIONS OVERVIEW POWER ENTRY BASICS PANEL-MOUNTED WORKSTATIONS..
PRODUCT MAP / TABLE OF CONTENTS.................. ELECTRICS & COMMUNICATIONS OVERVIEW............. POWER ENTRY BASICS PANEL-MOUNTED WORKSTATIONS.. POWER & COMMUNICATIONS BASICS PANEL-MOUNTED WORKSTATIONS.....................
More informationDESCRIPTION PRODUCT CODE LIST PRICE DIMENSIONS/INCHES H L D
EVE8PD - POWER DISTRIBUTION HOUSING Power housing is specified per beam size (e.g. EVE8PD36 is for use in a 36 beam). 8 wire, 4 circuits (2+2 configuration). Accommodates two duplex receptacles per panel
More informationMorrison, Currents and Reff Raceways Morrison, Currents and Reff Raceways
2+2 3+3 Morrison, Currents and Reff Raceways 1 Morrison, Currents and Reff Raceways. More. Better. pioneered 2+2, the office systems raceway with the right balance of convenience power and protected power
More informationKI WIREWORKS WIRE ELECTRICAL SYSTEM INTRODUCTION INFORMATION
KI WIREWORKS 810 10-WIRE ELECTRICAL SYSTEM INTRODUCTION INFORMATION 11/1/2005 810 10-WIRE ELECTRICAL SYSTEM COMMONLY ASKED QUESTIONS 11/1/05 1. Q. Is this electrical system a handed/directional system?
More informationRatchet-Pro Slide Cover
Wiremold/Legrand electrical systems conform to and should be properly grounded in compliance with requirements of the current National Electrical Code or codes administered by local authorities. Ratchet-Pro
More informationlighting, electrics & communications
lighting, electrics & communications P RO D U C T M A P / TA B L E C O N T E N T S.....................4 L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S O V E RV I E W....4 4 L I G H T
More informationlighting, electrics & communications
lighting, electrics & communications PRODUCT MAP / TABLE OF CONTENTS.................. LIGHTING, ELECTRICS & COMMUNICATIONS OVERVIEW.... LIGHTING BASICS................................. MODULAR DESK APPLICATIONS:
More informationlighting, electrics & communications
lighting, electrics & communications ELECTRICS & COMMUNICATIONS OVERVIEW............. LIGHTING BASICS................................. 205 POWER POLE BASICS............................... POWER ENTRY FROM
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationInstallation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper
Installation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper Caution 1 Read instructions through completely before proceeding; keep them for future
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More informationlighting, electrics & communications
lighting, electrics & communications P RO D U C T M A P...................................2 9 0 289 L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S O V E RV I E W....2 9 4 L I G H T I N
More informationlighting, electrics & communications
lighting, electrics & communications P RO D U C T M A P................................... 3 1 6 L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S B A S I C S...... 3 1 9 L I G H T I N G
More informationSURFACE CONTROLTrack INSTALLATION INSTRUCTIONS
SURFACE CONTROLTrack INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS - For use with CONTROLTrack System Only When installing or using this track system, basic safety precautions should always be
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationConfigurable Output Distribution. 120V / 208V / 240V 60Hz. User Manual English
Configurable Output Distribution 120V / 208V / 240V 60Hz User Manual English TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.......................... 1 GLOSSARY OF SYMBOLS....................................
More informationA-dec 570L Dental Light on a DCS System INSTALLATION GUIDE
A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE C ONTENTS Choose an Installation Guide...... Before You Begin.............. 3 Disconnect the Light Cable........ 3 Cut the Light Cable............
More informationCisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2
Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2 Cisco CRS 3-Phase AC Power Distribution Unit 2 Revised: November 18, 2016,
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationRack Installation Instructions
Rack Installation Instructions For System Storage EXP2512 and EXP2524 Express Storage Enclosures Use the instructions in this document to install an IBM System Storage EXP2512 Express Storage Enclosure
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationUSBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version
USBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version 2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla Street Chatsworth, CA 91311
More informationSystem Storage EXP3000 Rack Installation Instructions
System Storage EXP3000 Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When you install the IBM System Storage EXP3000 in a
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9011 Created 11/21/11 Kit Contents: Item # Qty. Component Description 1 2 Monitor Assembly 2 2 Remote Control 3 1 Cables # 3 4 1 Metal Wire Puller 5 1 Power Cord # 9 6 1 Owners Manual 7 2
More informationipod Classic Headphone Jack & Hold Switch Replacement
ipod Classic Headphone Jack & Hold Switch Replacement Replace Headphone Jack & Hold Switch to fix no audio and/or no unlock Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION
More informationWINSTA. Full Line Catalog 2008/2009
WINSTA Full Line Catalog 2008/2009 5 Contents FULL LINE CATALOG W4, Volume 1 Rail-Mounted Terminal Block Systems FULL LINE CATALOG W4 Rail-Mounted Terminal Blocks Volume 1 X-COM -SYSTEM Terminal Strips
More informationElectrical Accessories
2017 Price List and Specifications Brodart Co. Contract Furniture - Made in USA 280 North Road, Clinton County Industrial Park McElhattan, PA 17748 Toll-Free: 888-521-1884 E-Mail: furniture@brodart.com
More informationAP-120 Series AP Mounting Kit
AP-120 Series AP Mounting Kit Installation Guide The AP-120 series mounting kit provides additional mounting options for the AP-120 series wireless access points. The mounting kit includes the following
More informationUser s Guide. Includes Mounting, Installation, and Product Registration nd Avenue NE Arlington, WA USA (+1)
User s Guide Includes Mounting, Installation, and Product Registration 500 19009 62nd Avenue NE Arlington, WA USA (+1) 360-435-6030 European Sales Office Barcelona, España (+34) 600-843-845 www.outbackpower.com
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS! When using electrical equipment, basic safety precautions should always be
More informationA-dec 584 Monitor Mount on a Central Cabinet
Installation Guide A-dec 584 Monitor Mount on a Central Cabinet Before You Begin This procedure applies to the A-dec Inspire TM 592 Central Console and the standard and tall Preference cabinet central
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationILC LightLEEDer MicroLite 1000P Retrofit Installation
ILC LightLEEDer MicroLite 1000P Retrofit Installation Congratulations on the purchase of your new ILC LightLEEDer Retrofit System. The ILC LightLEEDer MicroLite Retrofit System is designed for the replacement
More informationInstalling 6 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing 6 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Overview...5 Installing the
More informationLighting PowerPincher Installation Instructions
PowerPincher Installation Instructions Lighting PowerPincher Installation Instructions Description The PowerPincher is an advanced energy saving control system, designed for general office use. It combines
More informationTrig Planning Guide. December 2012
Trig Planning Guide December 2012 Table of Contents Statement of Line Trig Applications - Conventional and Integration Specification Information Statement of Line Desks and Work Surfaces Support Options
More informationRack Mount Power Supplies
Rack Mount Power Supplies Installation Guide Models Include: VertiLine33D - 12VDC @ 8A - Sixteen (16) PTC protected outputs VertiLine33TD - 12VDC @ 16A - Sixteen (16) PTC protected outputs VertiLine63D
More informationHome Automation, Inc. Model 53A00-1. OmniTouch 5.7 Touchscreen with Video
Home Automation, Inc. Model 53A00-1 OmniTouch 5.7 Touchscreen with Video Installation Manual Document Number 53I00-1 Rev A June, 2007 FCC NOTICE This device complies with FCC Rules Part 15. Operation is
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationSTC7D. Digital Time Clock for TRC500 & TRC800. Installation, Operation, and Maintenance Manual
STC7D Digital Time Clock for TRC500 & TRC800 Installation, Operation, and Maintenance Manual READ AND SAVE THESE INSTRUCTIONS The purpose of this manual is to aid in the proper installation and operation
More informationPIX 515/515E. PIX 515/515E Product Overview CHAPTER
CHAPTER 4 PIX 515/515E This chapter describes how to install the PIX 515/515E, and includes the following sections: PIX 515/515E Product Overview Installing a PIX 515/515E PIX 515/515E Feature Licenses
More informationPXC Compact Unitary Equipment Controller (UEC)
Document No. 553-169 PXC Compact Unitary Equipment Controller (UEC) Product Description The PXC Unitary Equipment Controller (UEC) is an MS/TP device that can be configured as a programmable, stand-alone
More informationCone Beam Volumetric Tomography and Panoramic Dental Imaging System
Installation Manual Installation Manual Installation Manual Installation Manual Installation Manual Cone Beam Volumetric Tomography and Panoramic Dental Imaging System Gendex CB-500 Installation Manual
More informationON-FLOOR WIREWAY PRICELIST AUGUST 1, 2017
PRICELIST AUGUST 1, 2017 POWER AND TELECOM SOLUTION FOR TOP-OF-FLOORING INSTALLATION The new Trac On-Floor Wireway systems install directly on top of any type of flooring. They are the industry s newest
More informationConnector System for Fluorescent Lighting Fixtures. Connectors for In-Line Mounting of Fluorescent Lighting Fixtures. Fully Polarized Connectors
Connector System for Fluorescent Lighting Fixtures Connectors for In-Line Mounting of Fluorescent Lighting Fixtures Fully Polarized Connectors Luminaire Disconnect Connectors Pluggable Lighting Connectors
More informationEmerald Cubicle System. Spec Sheet. Emerald 39,52, 65 H. skutchi.com cubicles.cc. Vol DESIGNS. inc.
Emerald Cubicle System Spec Sheet 2018 Emerald 39,52, 65 H skutchi.com cubicles.cc Vol. 1 2018 Emerald Cubicles The diverse Emerald System has endless solutions for your office. Whether you are looking
More informationTopic: TB No.: Date: Aug/2017. Model UC4, UC10 & UC45 twin pump variants Regulated 24V Pump Power supply upgrade OVERVIEW
Topic: TB No.: 10041 Date: Aug/2017 Affected Machines: UC4/UC10 &45 variants Priority: Medium Created By: Gareth Fitzpatrick From Serial No.:
More informationAssembly Instructions for #5630 Medication PalWOW
Assembly Instructions for #5630 Medication PalWOW Before assembling, please familiarize yourself with all the parts and check to make sure you have all the parts as listed below. A B A & B - The box in
More informationElectrical Management System (EMS) EMS-HW30C & EMS-HW50C
Electrical Management System (EMS) EMS-HW30C & EMS-HW50C Installation & Operating Guide for: Model EMS-HW30C Rated at 120V/30A and Model EMS-HW50C Rated at 240V/50A Surgio Says Lifetime Warranty on all
More informationThe power behind competitiveness. Delta Infrasuite Power Management. Power Distribution Unit. User Manual.
The power behind competitiveness Delta Infrasuite Power Management Power Distribution Unit User Manual www.deltapowersolutions.com Save This Manual This manual contains important instructions and warnings
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationlighting, electrics & communications
lighting, electrics & communications LIGHTING, ELECTRICS & COMMUNICATIONS OVERVIEW.... 209 LIGHTING BASICS................................. 210 207 MODULAR DESKS APPLICATIONS: 207 POWER & DATA DISTRIBUTION.......................
More information3M Indoor Protected Building Entrance Terminal 4788V-QCS Series
The Network of Networks. 3M Indoor Protected Building Entrance Terminal 4788V-QCS Series with 3M Quick Connect System (QCS) 2811 Dry Flame Retardant Block for Field-Terminated Building Cables Instructions
More informationBasketball Shot Clock Set LX2180 Manual
Basketball Shot Clock Set LX2180 Manual 72 Industrial Boulevard Wrightsville, GA 31096 Phone: (800) 445-7843 Fax: (800) 864-0212 www.electro-mech.com LX2180 Revision 5 February 8, 2013 Table of Contents
More informationTemperature. Power requirements. Weight. Dimensions
Installing the Tracer Summit BMTX Building Control Unit Ordering numbers: BMTX001AAB000, BMTX001AAB010, BMTX001AAB001, BMTX001AAB011, BMTX001BAB000, BMTX001BAB010, BMTX001BAB001, BMTX001BAB011, BMTX001DAB000
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationPM Series Power Meter
PM Series Power Meter Quick Setup Guide - PMC-1000, PMC- 1001, PMM-1000, PMB-1960 Safety Information DANGER! HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Follow safe electrical work practices. See
More informationSignal Adapter. Signal Output. Power Input. Modell-Zug Elektronix Signal Adapter U.S.A. Momentary. Auxillary. Switch. Outputs
Adapter 1. Introduction Thank you for purchasing this product. The Adapter was specially designed to provide universal operation of the new generation of Märklin color light signals 74371, 74380, and 74391.
More information4888 and 4988 Outdoor Protected Entrance Terminals
4888 and 4988 Outdoor Protected Entrance Terminals Underwriters Laboratories (UL) Listed Instructions January 1997 34-7031-7272-5 Revision C Contents: 1.0 General... 1 2.0 Accessories... 2 3.0 Protector
More informationWith its tamper-resistant design, the
Dual-Channel 40N2 Series Nonmetallic Raceway Systems CableSmart Series Nonmetallic Raceway With its tamper-resistant design, the CableSmart 40N2 Series Raceway is ideal for schools or office settings,
More informationFlat Screen Garage. Table System Planning Guide WORKING FOR YOU
Flat Screen Garage Table System Planning Guide ORKING FOR YOU Introduction Bring a new level of performance to any room with KI s Flat Screen Garage. This versatile system does double duty to make the
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationMac Mini Mid 2011 SSD Dual Drive Installation
Mac Mini Mid 2011 SSD Dual Drive Installation Install a second hard drive in your mid 2011 Mac Mini. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 19 INTRODUCTION Use this guide to install
More informationREAD COMPLETELY BEFORE INSTALLING!!!
DOWNSHOT ECONOMIZER INSTALL INSTALLATION INSTRUCTIONS FOR 3-12.5 TON YORK PREDATOR GEN 7 OR NEWER ECONOMIZER DOWNSHOT CONFIGURATION CAS PART NUMBER 1023535 READ COMPLETELY BEFORE INSTALLING!!! IS NOT RESPONSIBLE
More informationQUICK SETUP GUIDE PMC-1000, PMC-1001, PMM-1000, PMB PM Series Power Meter. Safety Information. Equipment Maintenance and Service.
PM Series Power Meter QUICK SETUP GUIDE PMC-1000, PMC-1001, PMM-1000, PMB-1960 Safety Information DANGER! HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Follow safe electrical work practices. See NFPA
More informationHaworth Power Technical Sheets January 2018
Haworth Power Technical Sheets January 2018 Includes Accessories This page intentionally left blank. Table of Contents Desk Top Port Power Tap Cord Power Tap Conduit Enchanced Power Module Flip Top Unit
More informationU-SERIES SPECIFICATION GUIDE
U-SERIES SPECIFICATION GUIDE Connectivity with flexibility For more product information visit connectrac.com, call us at 877-480 - 5637 or email us at info@connectrac.com ADA COMPLIANT - U.L. TESTED AND
More informationSmartspace Benching System
SIN 711-2 Smartspace Benching System With the increase in office collaboration, comes an easy-to-install benching solution. Now that's smart thinking. Easily integrate power trough allows every workstation
More informationPAR+ & MSC+ Controller. Installation Manual
PAR+ & MSC+ Controller Installation Manual Contents Introduction... 1 System Configuration...1 Parts List and Tools Required for Installation...1 Installation Checklist...1 Mount Controller Pedestal on
More informationAB-2D AB-2D SPEAKER A,B OR A+B SELECTOR INSTALLATION & OPERATION GUIDE
M O D E L AB-2D AB-2D SPEAKER A,B OR A+B SELECTOR INSTALLATION & OPERATION GUIDE AB-2D Speaker/Amplifier Selector TABLE OF CONTENTS Introduction 1 Features and Benefits 1 Installation Considerations 3
More informationSM (SURFACE MOUNTED) WIREWAY: I SERIES
SM (SURFACE MOUNTED) WIREWAY: I SERIES DUPLEX POWER AND AV / TELECOM ANYWHERE The new Connectrac SM (Surface Mounted) Wireway installs directly onto any type of flooring. It s the industry s newest alternative
More informationEcoFlex LED Neon Manual
Manual Part number: LN-ECO-XXXX-10m from Environmental Lights is one of the most flexible and cost-effective members of our line of LED Neon products. It allows you to achieve the creative potential of
More informationNavigation interface for Jeep GC 5 RA2 NTV-KIT581
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Jeep GC Navigation interface for Jeep GC 5 RA2 NTV-KIT581 NNG-JEEP GC Kit Content 5 1 6 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8.
More informationCableSmart Series Nonmetallic Raceway
CableSmart Series Nonmetallic Raceway Dual-Channel 40N2 Series Nonmetallic Raceway System FIBER OPTIC CAT5 Wiremold CableSmart 40N2 Series Raceway is a large capacity nonmetallic raceway system that offers
More informationibook G3 14" Top Shield Replacement
Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The metallic top shield protects the logic board from electromagnetic interference. TOOLS: Coin (1) Paper Clip (1) Phillips
More information- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV
OVERVIEW The STR9 ELV is a long run, low power, linear surface mount LED lighting system designed for exterior architectural lighting applications. This guide contains important information on planning
More informationfor a perfect electrical installation. The range of rail-mounted terminal blocks
The range of rail-mounted terminal blocks for a perfect electrical installation. The range of rail-mounted terminal blocks for a perfect electrical installation. The new standard for rail-mounted terminal
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION MASKING TAPE
GUIDE PART NUMBER: 250-7616 GM SOFT TOUCH NAVIGATION SYSTEM GENERAL APPLICABILITY 2013- RAV4 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 NAVIGATION INTERFACE MODULE 2 1 VEHICLE INTERFACE T-HARNESS 3 1 LCD/GPS
More informationUpgrading LVDS Cables Instruction Sheet
Upgrading LVDS Cables Instruction Sheet INTRODUCTION Use the following instructions to replace the LVDS cables in CP2000-M/MR projectors. The new cables are slightly longer in length and allow for better
More information4188, 4288, 4288-S and 4688 Protected Entrance Terminals
4188, 4288, 4288-S and 4688 Protected Entrance Terminals Instructions Underwriters Laboratories (UL) Listed January 1997 34-7041-3837-8 Revision A Contents: 1.0 General... 1 2.0 Accessories... 2 3.0 Protector
More informationnls Product List 1st February, 2014 Tel: Fax: Coombes Drive, Penrith, NSW, 2750 Australia
15 Coombes Drive, Penrith, NSW, 2750 Australia 15 Coombes Drive Penrith NSW 2750 Tel: 02-4732 5444 Fax: 02-4732 6600 Email: sales@nlslight.com.au Product list for Electrical Accessories Code Item Inner
More informationCHANNEL LETTER LIGHTING UNIQUE LIGHTING SOLUTIONS RETROFIT INSTALLATION GUIDE
UNIQUE LIGHTING SOLUTIONS LIGHTING WARNING -Installation must only be performed by a licensed electrician. -To prevent death, injury or damage to property this product must be installed in accordance to
More informationDOCKING STATION SPECIFICATIONS
ONE PERSON STATION Power Outlets Data Jack Plate Mouse Brackets Front Covers Cable Holes Cable Holes Overview: The Docking Station distributes power, data, and laptop storage to each user. It also offers
More informationipod Classic Click Wheel Replacement Written By: irobot ifixit CC BY-NC-SA Page 1 of 25
ipod Classic Click Wheel Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION The click wheel receives the feedback of your fingers and transmits it to the logic board.
More informationInstalling the PSU for the S50 and S50N
Installing the PSU for the S50 and S50N Caution: Use only the power cords supplied with the power supply. Do not supply power to your S50 or S50N system until the power supply and modules have been installed.
More informationMCG Surge Protection
299-700-33B 299-700-33A MCG Surge Protection Installation/Operating Instructions for MCG 500 Series Important Warranty Information MCG surge protectors are designed to work at specific voltages and configurations,
More informationPower Base AI. Power Base AI. Technical Sheets
Power Base AI Power Base AI Technical Sheets odular Electrical System System Overview Haworth s Power Base AI modular electrical system provides a flexible, reconfigurable power distribution infrastructure
More informationInstruction Manual. Electrical Management System (EMS) EMS-HW30C & EMS-HW50C
Instruction Manual Electrical Management System (EMS) EMS-HW30C & EMS-HW50C EMS-HW50C EMS-HW30C! CAUTION These instructions are intended to provide assistance with the installation of this product, and
More informationOperation and Maintenance Manual
VM Series Operation and Maintenance Manual VM - Voltage Monitor VM-100-24 V VM-100-48 V VM-100-125 V VM-100-250 V EAGLE EYE POWER SOLUTIONS All Rights Reserved. 1 The Voltage Monitor series reads battery
More information