Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4

Size: px
Start display at page:

Download "Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4"

Transcription

1 Olympus X and X6 Installation Instruction for Microscope End Users (easy install version) PN 07 Olympus X_6 Illuminator ssy dditional Items Included ut Not Shown: PN 077 Hex Key mm PN 060 Hex Key mm M VH tape PN 06 Pot-Plate-Cable ssy X_6 (easy install) PN 0 SHCS M x 0.7 x 0mm PN 07 Power Supply - XP Power 5V Fixed lade US Input/US Output PN 05 Knob 0.50 dia. PN 07 Cable ssy.5mm ID x.5mm OD R plug to US 6 foot The illuminator may be powered by plugging the cable into the power supply provided, or into a suitable US port on a computer or other device. Copyright 09 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Power supplies are subject to substitution without notice due to availability issues and changes in regulations. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator OF 9

2 Step : Place the microscope upside down, unplug the existing X illuminator cable, and unscrew the existing illuminator unit from microscope port as shown, using the mm hex key provided. Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator OF 9

3 Step : Disassemble back cover. Note that after installation of the Nanodyne illuminator, there should be no power connections left in place to the DC power inlet (red circle). ** Safety and misc. ** Regardless whether the original circuitry is left in place or removed, be sure there is no possibility of electrical hazard in case an unfamiliar user connects power to the old DC input. The original 0/0VC powered illuminator circuitry (red arrow) is completely replaced by the Nanodyne equipment which is powered by a universal input wall plug power supply with low voltage DC output. The original circuitry may be left in place, or removed as it is no longer used. We recommend removing the power cable from the DC input connector. It should be cut short so there is no possibility it could be connected to the original circuitry, or insulated with heat shrink tubing or electrical tape. Han-Seung Yang //09 Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. PN 08 Olympus X_6 Illuminator OF 9

4 The original pot cable may be left in place, or removed as it is no longer used. Step : Place the microscope back to upright position, then remove now-obsolete power on/off switch using mechanical tools such as flat screw driver or tweezers. Step : Insert a new potentiometer (PN 06) along with Pot Plate (PN 060 Type ack) to the power switch hole as shown in left. The Pot Plate exactly fits to the hole. Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator OF 9

5 Remove the protective release film Step 5: Remove the release film and assemble front Pot Plate (PN 059 Pot Plate Type ) along with washer and nut using mm hex socket (red circle above), then install a new pot knob (PN 05) provided using.5mm hex key as shown in below. Pot knob set screw and cutaway portion of shaft must be aligned as shown in detail. Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator 5 OF 9

6 Step 6: Make sure all the original circuitry cables are disconnected (red circles) as shown in left. Step 7: Reinstall the back cover and place the microscope upside down as shown in left. Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator 6 OF 9

7 Step 8: Insert PN 0 hex screw (red circle) to the screw hole of the Nanodyne adapter as shown above, insert Nanodyne illuminator unit to the microscope port, and tighten the hex screw to secure Nanodyne illuminator in place. Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator 7 OF 9

8 Step 9: Connect the pot cable, note that the connector will only seat one way, so do not force it in if it does not fit. Secure the cables as shown above (using M VH tape if needed). Place the microscope back to upright position, plug C adapter to the Nanodyne illuminator, and now it is ready to use. *Note: The Pot Cable insertion procedure will be shown in next page. Tape to secure wires. Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator 8 OF 9

9 efore Insertion Partial Insertion Connect the socket at the end of the Pot Cable ssembly to the mating socket of the illuminator, as shown in the pictures on this page. fter partially inserting the socket to the mating socket of the illuminator with your finger, use other mechanical tools such as driver or tweezer to firmly insert the socket all the way by pushing back edge of the socket as indicated with the red arrow in the image (top right). The socket cannot be fully engaged by pushing on the wire attached as the wires would just collapse. If you want to pull the socket out, pull the wire straight out by firmly gripping the black heat shrink tubing. Full Insertion Copyright 08 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator 9 OF 9

Olympus BX43_46 Installation Instruction (OEM Adjust) 4

Olympus BX43_46 Installation Instruction (OEM Adjust) 4 Olympus X_6 Installation Instruction (OEM djust) If you are not an experienced repair tech please consider the alternate (easy install) version dditional Items Included ut Not Shown: PN 07 Olympus X Illuminator

More information

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator.

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document

More information

Included Items Not Shown:

Included Items Not Shown: PN 09 HP Illuminator ssy Olympus HS Installation Instructions - Nanodyne Illuminator for Olympus HS Microscope Figure. Parts included in Olympus HS Illuminator System. Included Items Not Shown: PN 057.5mm

More information

Original Zeiss Axiovert Illuminator. Nanodyne Replacement Illuminator for Zeiss Axiovert

Original Zeiss Axiovert Illuminator. Nanodyne Replacement Illuminator for Zeiss Axiovert Zeiss xiovert Replacement Instructions - Original and Nanodyne Replacement Original Zeiss xiovert Illuminator Nanodyne Replacement Illuminator for Zeiss xiovert Copyright 06 Nanodyne Measurement Systems.

More information

Nanodyne Replacement Illuminator for Zeiss Axiovert Microscope Installation Instructions

Nanodyne Replacement Illuminator for Zeiss Axiovert Microscope Installation Instructions Nanodyne Replacement Illuminator for Zeiss xiovert Microscope Installation Instructions Note that this photo shows an older version of the illuminator. The current version is shown on the sheet. Original

More information

Installation Guide. Retrofit Kit for USB Ready Intraoral Systems

Installation Guide. Retrofit Kit for USB Ready Intraoral Systems Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the

More information

Solid State Control Calibration Procedure MKG Solid State Griddles - All Options

Solid State Control Calibration Procedure MKG Solid State Griddles - All Options Solid State Control Calibration Procedure MKG Solid State Griddles - All Options The following procedure describes the steps to calibrate the Solid State Temperature Control for any of the MKG-ST Griddle

More information

Encore XT Manual Gun Upgrade Kit

Encore XT Manual Gun Upgrade Kit Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.

More information

E1135C PDU and Pod Upgrade Procedure

E1135C PDU and Pod Upgrade Procedure E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support

More information

EQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.

EQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors. EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about

More information

SERIES 5 TABLES/BENCH

SERIES 5 TABLES/BENCH Wire Manager Driveshaft Driveshaft Cover Stretcher Power Cable Low-Voltage Cable Power Supply Master Motor (can be on either side) Controller Controller Cable Lifting Column Foot SERIES 5 TABLES/BENCH

More information

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.

More information

Power Cable. Low-Voltage Cable

Power Cable. Low-Voltage Cable Troubleshooting Guide Power Cable Low-Voltage Cable Wire Manager Power Supply Driveshaft Driveshaft Cover Master Motor (can be on either side) Controller Controller Cable Lifting Column Foot Stretcher

More information

Q2 XBee Handheld Controller Assembly Guide

Q2 XBee Handheld Controller Assembly Guide Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:

More information

Electronic Balance Ionizer STABLO-AP Service Manual

Electronic Balance Ionizer STABLO-AP Service Manual 321-78209 Jan. 2016 Electronic Balance Ionizer STABLO-AP Service Manual Analytical & Measuring Instruments Division This page is intentionally left blank. Table of Contents 1. Precautions for Troubleshooting...

More information

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the

More information

HDMI Upgrade for the Showcase DVD

HDMI Upgrade for the Showcase DVD THE LEADER IN AUDIO ENGINEERING for the Showcase DVD INSTALLATION AND SETUP GUIDE Getting Started THERE ARE NO USER- SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT. Krell authorizes this HDMI upgrade to the

More information

Yamaha DX7 LCD Installation Guide

Yamaha DX7 LCD Installation Guide Table of Contents Required Tools/ Getting Started... p. 2 Installation... p.3-11 Opening the DX7... p. 3 Locating and Removing the LCD Bracket... p. 4 Removing the LCD Bezel Cover... p. 5 Removing the

More information

Installing a Power over Ethernet injector

Installing a Power over Ethernet injector Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart

More information

Replace the edrive TINI Module and Battery

Replace the edrive TINI Module and Battery Product All edrive Configurations Special Information INFORMATION: This service bulletin is for informational purposes only. It is intended for use by Northrop Grumman Cutting Edge Optronics (NG CEO) employees

More information

Memory Expansion for DriveLogix Controller

Memory Expansion for DriveLogix Controller Installation Instructions Memory Expansion for rivelogix ontroller!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work

More information

Upgrade Instructions. P/N Revision A. October Printer Terminal Holder * *

Upgrade Instructions. P/N Revision A. October Printer Terminal Holder * * Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers

More information

ATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

ATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES 15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the

More information

Installing and Upgrading Memory and Virtual Private Network Modules

Installing and Upgrading Memory and Virtual Private Network Modules APPENDIX C Installing and Upgrading Memory and Virtual Private Network Modules This chapter tells how to install or upgrade memory and how to install a Virtual Private Network (VPN) module in your Cisco

More information

imac Intel 21.5" EMC 2389 Stand Replacement

imac Intel 21.5 EMC 2389 Stand Replacement imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION

More information

An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT

An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0597 Kepco KIT 219-0597 contains the PROMs used to upgrade the firmware for BOP

More information

PoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.

PoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power

More information

MPS-850 e-drum set. assembly instructions

MPS-850 e-drum set. assembly instructions MPS-850 e-drum set assembly instructions Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 16.10.2018,

More information

JLTX Lever and Joystick Replacement Instructions

JLTX Lever and Joystick Replacement Instructions JLTX Lever and Joystick Replacement Instructions WARNING THE INCORRECT INSTALLATION OF A LEVER OR JOYSTICK CAN CAUSE AN EQUIPMENT MALFUNCTION FAILURE TO FOLLOW THIS PROCEDURE CAREFULLY COULD RESULT IN

More information

TDM To MiniMech conversion ProceDure

TDM To MiniMech conversion ProceDure TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT

More information

ATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

ATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard

More information

Firebox X Edge e-series De-Manufacturing Instructions

Firebox X Edge e-series De-Manufacturing Instructions Firebox X Edge e-series De-Manufacturing Instructions Document Number: 480-2530-001 WatchGuard Technologies. Doc #480-2530-001 Rev. A Page 1 of 9 1.0 Purpose This instruction defines the de-manufacturing

More information

A Backlighted LCD for your K1

A Backlighted LCD for your K1 A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification

More information

Richter Optica. Instructions for Model: MDS2 Middle School Microscope

Richter Optica. Instructions for Model: MDS2 Middle School Microscope Richter Optica info@richter-optica.com Instructions for Model: MDS2 Middle School Microscope Eyepiece 360 Rotatable Head Revolving Nosepiece Carrying Handle Objectives Rack Stop Stage Stage Clips Disc

More information

TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE

TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05

More information

Intel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide

Intel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers

More information

Richter Optica. Instructions for Model: HSX1 High School Microscope

Richter Optica. Instructions for Model: HSX1 High School Microscope Richter Optica info@richter-optica.com Instructions for Model: HSX1 High School Microscope Eyepiece 360 Rotatable Head Objectives Carrying Handle Revolving Nosepiece Rack Stop Slide Holder Focus Tension

More information

Written By: Walter Galan

Written By: Walter Galan imac Intel 21.5" EMC 2428 CPU Replacement Replace the CPU in your imac Intel 21.5" EMC 2428. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION Use this guide to upgrade

More information

Raven Adapter Harness

Raven Adapter Harness Note: Indented items indicate parts included in an assembly listed above Quantity by System Part Name/Description Part Number With Switch Box With Built-in Switches Raven Harness Adapter Kit 4100504 1

More information

Male header, 100% protected against mismating, (1 x 1) mm straight solder pins Pin spacing 3.5 mm 3.81 mm. light gray <_ 8,5_> 3,5 1x1 <_ 9,3_>

Male header, 100% protected against mismating, (1 x 1) mm straight solder pins Pin spacing 3.5 mm 3.81 mm. light gray <_ 8,5_> 3,5 1x1 <_ 9,3_> 96 Male Headers with Solder Pins; Double-Deck Male Headers with Solder Pins, Pin Spacing 3.5 mm and 3.81 mm 160 V/.5 kv/ 300 V, 10 A U 10 A 300 V, 10 A 160 V/.5 kv/ 300 V, 10 A U 10 A 300 V, 10 A 160 V/.5

More information

edrive RAM Battery Alternate Replacement Procedure

edrive RAM Battery Alternate Replacement Procedure edrive RAM Battery Summary This technical note describes the process for replacing the TINI RAM battery with a higher capacity battery. With the edrive turned on, the external battery can be changed without

More information

BreezeMAX Wi² and BreezeACCESS Wi² Quick Installation Guide

BreezeMAX Wi² and BreezeACCESS Wi² Quick Installation Guide This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the BreezeMAX Wi² and BreezeACCESS Wi² System Manual. Wi² Package Content Check

More information

Validator Update Instructions for Rowe BC1200 $1 - $20

Validator Update Instructions for Rowe BC1200 $1 - $20 Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit

More information

2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual

2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual 2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation

More information

MAIN PCB (The small one)

MAIN PCB (The small one) THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed

More information

Replacing the Power Supply

Replacing the Power Supply APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools

More information

KNIGHT S GALLOP ALGO-RHYTHMIC GENERATOR BUILDING GUIDE

KNIGHT S GALLOP ALGO-RHYTHMIC GENERATOR BUILDING GUIDE KNIGHT S GLLOP LGO-RHYTHMIC GENERTOR UILDING GUIDE Table of Contents 01. Components List + Tools 02. PC Sides 03. Important Note 04. Top PC ssembly 04_1. Diode 1N4148 04_2. Laying Resistors 04_3. Zenner

More information

Megatouch FORCE Monitor Chassis Board Replacement

Megatouch FORCE Monitor Chassis Board Replacement Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis

More information

Removal and Installation8

Removal and Installation8 8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever

More information

CODE 50108, 50110, 50164, 50165

CODE 50108, 50110, 50164, 50165 CODE 50108, 50110, 50164, 50165 ASSEMBLY PAGE NAME Machine Assembly Machine Assembly Machine Assembly (Wire feed chamber) Machine Assembly (Wire feed chamber) Feeding Unit Assembly CODE NO.: K NO.: FIGURE

More information

SP-100. Service Manual Aug. 02

SP-100. Service Manual Aug. 02 SP-100 Service 2004. Aug. 02 1. Caution for maintenance and Service. Please take care below points when you do Service and Maintenance. (1) Service and Maintenance should be done under safety condition.

More information

CubePro. Main PCB Replacement Guide. Prosumer 3D Printer. Original Instructions

CubePro. Main PCB Replacement Guide. Prosumer 3D Printer. Original Instructions CubePro Prosumer 3D Printer Main PCB Replacement Guide Original Instructions 1 INTRODUCTION COPYRIGHT 2014 by All rights reserved. This document is subject to change without notice. This document is copyrighted

More information

Figure 4-29 Removing the CPU compartment cover

Figure 4-29 Removing the CPU compartment cover 4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment

More information

Mi50 Inverted Microscope User s Manual. Fein.

Mi50 Inverted Microscope User s Manual. Fein. Mi50 Inverted Microscope User s Manual Fein info@feinoptic.com Mi50 Microscope Components Siedentopf Trinocular Head Stage Plate Mechanical Stage Locking Screw Hex Wrench Storage Beam Splitter Dust Protector

More information

INSTRUCTION MANUAL. * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA

INSTRUCTION MANUAL. * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA INSTRUCTION MANUAL * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA INSTRUCTION MANUAL Thank you for purchasing this product. For proper usage and application,

More information

Plasma Panel Replacement Guide DU-42PX12X

Plasma Panel Replacement Guide DU-42PX12X Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be

More information

IPhone 7 Plus Chargeport REPAIR GUIDE. Version Edition

IPhone 7 Plus Chargeport REPAIR GUIDE. Version Edition IPhone 7 Plus Chargeport REPAIR GUIDE Version 1 2016 Edition IPhone 7 plus Chargeport Repair Guide RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL,

More information

Navigator II INstallatIoN MaNUal For static and PaN/tIlt configurations

Navigator II INstallatIoN MaNUal For static and PaN/tIlt configurations Navigator II Installation MANUAL For Static and Pan/Tilt Configurations Document Number: 432-0001-00-12, rev 100 FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole

More information

RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2

RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 Dear Do-It-Yourselfer, The stock FlatCap2 is less than a stellar performer. Used with a CD5 CD player, for example, it gives flabby bass control,

More information

CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS

CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075

More information

L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGNOSTIC ADDENDUM

L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGNOSTIC ADDENDUM 111 Canfield Avenue Randolph, New Jersey 07869 1-800-LANDICE FAX 973-927-0630 L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGSTIC ADDENDUM High-Tech Entertainment Center Explosion Part

More information

MAGIXBOX TM. Quick Start Guide

MAGIXBOX TM. Quick Start Guide TM TM by TouchMagix MAGIXBOX TM Quick Start Guide What s in the box: Ankle Ceiling Plate Extendable Rod Connector Piece Middle Piece Universal Spider Super clamp with ball socket Safety Cable Projector

More information

M5 and M10 Routers Power Supply and Power Cord Component Replacement Instructions

M5 and M10 Routers Power Supply and Power Cord Component Replacement Instructions M5 and M10 Routers Power Supply and Power Cord Component Replacement Instructions Part No. 530-003244-01 Revision 1 27 July 2000 This document describes how to remove and replace the AC and DC power supplies,

More information

GPIB-232CT-A IBCL EPROM Installation Guide

GPIB-232CT-A IBCL EPROM Installation Guide NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.

More information

xtablet T1600 Vehicle Holder Installation Guide

xtablet T1600 Vehicle Holder Installation Guide This document will step you through setting up the T1600 Vehicle Holder installation and tips for a safe, clean and long lasting installation. Preparing to Mount the Vehicle Holder Warning : Dock mounting

More information

AutoScan to MultiScan Replacement Kit

AutoScan to MultiScan Replacement Kit Instruction Sheet P/N AutoScan to MultiScan Replacement Kit WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other

More information

Installing the Server into a Rack

Installing the Server into a Rack Installing the Server into a Rack Note These instructions apply to multiple models; illustrations may vary slightly. Rack Mount Kit Inventory Before installing the chassis on a standard 4-post rack, make

More information

CDRPan. Installation. Instructions for Siemens / Sirona Orthophos 3 FOR PANORAMIC SYSTEMS

CDRPan. Installation. Instructions for Siemens / Sirona Orthophos 3 FOR PANORAMIC SYSTEMS CDRPan FOR PANORAMIC SYSTEMS Installation Instructions for Siemens / Sirona Orthophos 3 Schick Technologies, Inc. 31-00 47 th Avenue Long Island City, New York 11101 (718) 937-5765 (718) 937-5962 (FAX)

More information

BL-FLOWSTN-P FlowStation Module Installation Guide

BL-FLOWSTN-P FlowStation Module Installation Guide Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port

More information

Procedure to Install an IO Expansion Cage Assembly in a Maxum II Modular Oven Analyzer

Procedure to Install an IO Expansion Cage Assembly in a Maxum II Modular Oven Analyzer Procedure to Install an IO Expansion Cage Assembly in a Maxum II Modular Oven Analyzer Difficulty Level: Medium Estimated time to execute: 1 Hour Revision History Issue Date Reason 001 5/31/2016 Initial

More information

Control Box Setup - PRSalpha

Control Box Setup - PRSalpha 888-680-4466 ShopBotTools.com Control Box Setup - PRSalpha Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Parts List: Hooking Up a PRSalpha Gantry Tool Powering the

More information

Installation and Maintenance

Installation and Maintenance CHAPTER 4 Installation and Maintenance Revised: April 19, 2010, Introduction This chapter explains how to install a SCE 1000 platform in a rack or in a general tabletop or workbench installation. Additionally,

More information

INSPECTION TOOL. Inspection Video Camera with Color LCD Monitor. EU Environmental Protection. Model: 8802LE,8803LE. Model: 8802LE,8803LE

INSPECTION TOOL. Inspection Video Camera with Color LCD Monitor. EU Environmental Protection. Model: 8802LE,8803LE. Model: 8802LE,8803LE INSPECTION TOOL Inspection Video Camera with Color LCD Monitor Model: 8802LE,8803LE EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle

More information

LED Lighting Kit For Elara NanoEdge Fixed Frame. Installation Guide. Attention: Read this guide before assembling your screen.

LED Lighting Kit For Elara NanoEdge Fixed Frame. Installation Guide. Attention: Read this guide before assembling your screen. LED Lighting Kit For Elara NanoEdge Fixed Frame Installation Guide Attention: Read this guide before assembling your screen. INTRODUCTION GETTING STARTED WARNING - Sharp Edges This product may contain

More information

- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV

- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV OVERVIEW The STR9 ELV is a long run, low power, linear surface mount LED lighting system designed for exterior architectural lighting applications. This guide contains important information on planning

More information

CARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS

CARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS CARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS CAUTION: The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the printhead. Please

More information

HGR-2488 Prism Installation Instructions

HGR-2488 Prism Installation Instructions HGR-2488 Prism Installation Instructions These installation instructions are applicable to the following models: TASCAM 2488 MK1 (original model) TASCAM 2488 MK II TASCAM 2488 NEO Page 1 of 8 Important

More information

V5420 Host Card Upgrade Kit for R3082D Quick Start Guide

V5420 Host Card Upgrade Kit for R3082D Quick Start Guide Quick Start Guide Upgrade kit contents The table below shows the contents of the V5420 Host Card Upgrade Kit (components are not shown to scale). Part Function Pieces V5420 Host Card 1 Host card bracket

More information

OV1016 Part No OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM USER GUIDE

OV1016 Part No OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM USER GUIDE OV1016 Part No. 86042 OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM USER GUIDE PRODUCT OVERVIEW User Guide: OV1016 OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM Our best-selling value table base is now available

More information

Star Trac Fitness E-ST 5090 Stepper. Install Guide

Star Trac Fitness E-ST 5090 Stepper. Install Guide Star Trac Fitness E-ST 5090 Stepper Install Guide STAR TRAC E-ST STEPPER Install Guide E-ST 5090 E Series Stepper ASSEMBLY AND SETUP The following parts are included with the base STAR TRAC E-ST STEPPER:

More information

WARNING ELECTRICAL SHOCK HAZARD

WARNING ELECTRICAL SHOCK HAZARD Description Safety Instructions The top-entry sub D9 connector kit is designed for enclosure sizes D1h D8h, E1 E2, and E1h E4h with VLT PROFIBUS DP MCA 101 option. It fits the following drives: VLT HVAC

More information

Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox

Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR

More information

Operating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and gold plated contacts available High

Operating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and gold plated contacts available High Operating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and contacts available High performance insulation material General characteristics and technical

More information

Canon Powershot A70 Button Flex Assembly Replacement

Canon Powershot A70 Button Flex Assembly Replacement Canon Powershot A70 Button Flex Assembly Replacement Written By: Brian ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION This guide will walk through the process of removing the button flex assembly

More information

Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly

Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,

More information

PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board

PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board Service Bulletin PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board Contents This publication provides instructions for replacing the gate power board for PowerFlex 400 Frame G and

More information

Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved

Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved Introduction Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module have failed

More information

Description: Detailed procedure on removing old bushing and installing new Brake Bushing Replacement Kit 10447

Description: Detailed procedure on removing old bushing and installing new Brake Bushing Replacement Kit 10447 Procedure: BRAKE BUSHING REPLACEMENT PROCEDURE Product: Document #: Rev: Page: MODEL 7000, 7000A, & 8000 GYRO 078 1 1 of 14 Description: Detailed procedure on removing old bushing and installing new Brake

More information

Biesemeyer Fence Kit Installation Instructions:

Biesemeyer Fence Kit Installation Instructions: Biesemeyer Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Biesemeyer Commercial Fence. Accurate Technology manufactures kits for other saw

More information

In-Sight 7000 Series Vision System. Optional Configurations

In-Sight 7000 Series Vision System. Optional Configurations In-Sight 7000 Series Vision System Optional Configurations Legal Notices The software described in this document is furnished under license, and may be used or copied only in accordance with the terms

More information

CINTENNA ANTENNA REPAIR GUIDE

CINTENNA ANTENNA REPAIR GUIDE The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter

More information

Instructions for installing your QuiltCam on your Gammill quilt machine.

Instructions for installing your QuiltCam on your Gammill quilt machine. Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video

More information

BPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

BPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical

More information

Projectors 6 and 7 Ruggedized Lens Components Installation Manual

Projectors 6 and 7 Ruggedized Lens Components Installation Manual Projectors 6 and 7 Ruggedized Lens Components Installation Manual This document includes the procedures required to install the ruggedized lens components for Projectors 6 & 7 (Matrix 4000 M / 38-DSP104-09).

More information

Series 3700 Screw Terminal Assemblies Installation Instructions

Series 3700 Screw Terminal Assemblies Installation Instructions Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY www.keithley.com Series 3700 Screw Terminal Assemblies Installation Instructions Introduction This document contains handling

More information

PRODUCT MANUAL Duet DMX & Wireless RGB-W Controller

PRODUCT MANUAL Duet DMX & Wireless RGB-W Controller Product Description Solid Apollo LED s new wall mounted Duet DMX & RGB-W LED Controller has been created to control LED light fixtures in three different ways. Users can independently control DMX enabled

More information

LED. Sign Module. Assembly Manual

LED. Sign Module. Assembly Manual LED Sign Module Assembly Manual 6/14/2002 3:10 PM 6 2 3 3 E. S a w g ra s s R d S a ra s o ta, F L. 3 4 2 4 0 (9 4 1 )3 7 7-5 7 7 5 F A X(9 4 1 )3 7 8-4 2 2 6 www.acscontrol.com Table of Contents Table

More information

DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL

DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL Version 2.1 June 4, 2013 0 Table of Contents Low Profile Pan Tilt Kit Description... 3 Low Profile Pan Tilt Unit Basic Operation... 4 Mounting

More information

Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays

Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40 - 55 flat Panel Displays Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays Model: DS-VWT955-2X2 EXTENSION COLUMN (SOLD SEPARATELY) COMPATIBILITY Display width must be a minimum of 36"

More information

E2460GS Oscilloscope Upgrade Kit

E2460GS Oscilloscope Upgrade Kit Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent

More information