3-slot Backplane For RC2014 User Guide

Transcription

1 3-slot Backplane For RC204 User Guide For module: SC6 version.0 Design and Documentation by Stephen C Cousins Edition.0.0,

2 CONTENTS OVERVIEW...2 PRINTED CIRCUIT BOARD... 4 SCHEMATIC... 6 WHAT YOU NEED...7 COMPONENTS: WHAT THEY DO & WHERE TO GET THEM...9 ASSEMBLY GUIDE... 4 PURCHASING THE PRINTED CIRCUIT BOARD...23 HISTORY...25 CONTACT INFORMATION... 26

3 Overview A three slot backplane is all that is required for a minimal RC204 system. The picture below shows a CP/M system made from: SC08 - Z80 CPU, RAM & ROM module RC204 Compact Flash module RC204 Dual Serial module (other suitable serial modules are available) 2

4 This backplane has three RC204 (80 pin) card sockets and a power supply input. Pin 40 of the standard RC204 bus is used for the Z80 interrupt daisy chain signal IEO, with the 40 th pin of the enhanced bus, sometimes called pin 80, being used for the IEI signal. These two pins therefore do not connect to all 3 sockets in parallel, but instead link pin 40 of one socket to pin 80 of the next, forming a chain. 3

5 Printed Circuit Board The printed circuit board is 0.6 mm by 49.5 mm (4.00 inches by.95 inches). Circuit board, top/component side Circuit board, bottom/solder side 4

6 The circuit board s layout and dimensions are shown below. 5

7 Schematic A high quality version of the schematic is available as a separate PDF. Errata None yet. 6

8 What You Need The following components are required to assemble the module with its full functionality and jumper options. Header pins P, may need to be cut from longer strips. Image Qty Reference Description PCB Printed circuit board SC6 Backplane with PSU C to C3 Capacitor 00nF, ceramic, lead spacing = 2.54mm P Pin header, male, row x 2 pins, angled K to K3 Pin header, socket, 2 rows x 40 pins, straight R Resistor 470R, axial, 5%, carbon film, 0.25W or 0.25W R2 Resistor 4k7, axial, 5%, carbon film, 0.25W or 0.25W LED LED, green, 3mm SW Switch, tactile toggle, sub-miniature, SPDT SW2 Switch, tactile button J Socket, power, barrel, 2.mm J2 Screw terminal, 2 way, 5.08mm pitch Also required to assemble the module from the above components: Long nose pliers Side cutters Soldering iron 7

9 Solder PCB cleaning materials 8

10 Components: What They Do & Where To Get Them Each component is described below. I have listed multiple sources for most components, but have not actually tried all of them, so best treat the specified part numbers as guidance only. Where ebay is listed as a supplier, the part is likely to be cheaper there than the other sources, sometimes considerably cheaper. Further savings are usually possible by ordering parts direct from countries like China. PCB Image Qty Reference Description PCB Printed circuit board SC6 Backplane with PSU Supplier EasyEDA Tindie Part number Search EasyEDA.com for RC204 Backplane Search Tindie for SC6 or RC204 Backplane The PCB is currently only available to be ordered from EasyEDA.com, although you can download the Gerber and send it to your preferred manufacturer. C to C3 Image Qty Reference Description C to C3 Capacitor 00nF, ceramic, lead spacing = 2.54mm 3 Supplier Part number Farnell Mouser 75-C0Z5U04M050R RS These capacitors provide power supply decoupling (or bypass). The fast switching in digital circuits creates spikes on the power supply lines which are suppressed with decoupling capacitors placed at key points on the circuit board. 9

11 P Image Qty Reference Description P Pin header, male, row x 2 pins, angled Supplier ebay Farnell Mouser RS Part number (x40 pin to be cut to length) (x40 pin to be cut to length) (x40 pin to be cut to length) (x40 pin to be cut to length) This header allows an external reset switch to be connected to the backplane. Fitting this header is optional. K to K3 Image Qty Reference Description K to 3 Pin header, socket, 2 rows x 40 pins, straight 3 Supplier ebay ebay Farnell Mouser RS Part number (from UK) (from Hong Kong) (very expensive) RK (very expensive) (very expensive) These connectors are the sockets into which RC204 modules are plugged. 0

12 R Image Qty Reference Description R Resistor 470R, axial, 5%, carbon film, 0.25W or 0.25W Supplier Part number Farnell Mouser 603-CFR-25JR-52470R RS This is the current limit resistor for the power LED indicator. The value can be reduced to 330R if you want a really bright light, or increased to about k if you d rather have a very dim light. If in doubt use the suggested value of 470R. R2 Image Qty Reference Description R2 Resistor 4k7, axial, 5%, carbon film, 0.25W or 0.25W 2 Supplier Part number Farnell Mouser 603-CFR-25JR-524K7 RS This resistor pulls up the reset line when the reset switch is not being pressed. LED Image Qty Reference Description LED LED, green, 3mm Supplier Part number Farnell 584 Mouser 859-LTL-423N RS Power to the backplane is indicated by this LED.

13 SW Image Qty Reference Description SW Switch, tactile toggle, sub-miniature, SPDT Supplier Part number ebay Farnell Mouser CMSP2B2M2QT RS This switch turns on and off power from J or J2. It does not control power from other sources, such as FTDI style serial cables. SW2 Image Qty Reference Description SW2 Switch, tactile button Supplier Farnell Mouser RS Part number (red button) 506-FSM4JH (red button) (black button) This is the reset switch, which pulls down the backplane s RESET signal. J socket Image Qty Reference Description J Socket, power, barrel, 2.mm Supplier Part number Farnell Could not find a matching part Mouser 63-79PH-EX RS The barrel connector provides one means of connecting a regulated 5 volt DC supply to the backplane. The centre pin is positive. 2

14 J2 terminal Image Qty Reference Description J2 Screw terminal, 2 way, 5.08mm pitch Supplier Farnell Mouser RS RS Part number (green) H02B0LF (green) (green) (black) The screw terminal connector provides one means of connecting a regulated 5 volt DC supply to the backplane. The power supply must be regulated 5 volt D.C. ideally in the range of 4.9 to 5. volts. The components will tolerate up to 5.5 volts, but the nearer to 5.0 volts the better. The power supply must be capable of delivering all the current the system requires without the voltage dropping. The current depends on factors such as how many modules are connected, but a modest system will typically use less than 250 ma. 3

15 Assembly Guide This guide assumes you are familiar with assembling circuit boards, soldering and cleaning. If not, it is recommended you read some of the guides on the internet before continuing. First check you have all the required components, as listed in the section What You Need. Header pins P, may need to be cut from longer strips. 4

16 Step Fit and solder R (shown in red below). Colour code for 470R resistor: Yellow, Violet, Brown Fit and solder R2 (shown in yellow below). Colour code for 4k7 resistor: Yellow, Violet, Red These can be fitted either way round, as they are not polarity dependent. 5

17 Step 2 Fit and solder capacitors C to C3. These can be fitted either way round, as they are not polarity dependent. 6

18 Step 3 Fit and solder P. This header allows an external reset switch to be connected to the backplane. Fitting this header is optional. 7

19 Step 4 Fit and solder SW (shown in red below). Fit and solder SW2 (shown in yellow below). 8

20 Step 5 Fit and solder K to K3. 9

21 Step 6 Fit and solder LED. It is important to fit this component the right way round. The cathode lead is usually shorter than the anode lead, and the cathode side is usually marked with a flat side on the plastic. The cathode is nearest the on/off switch (SW). 20

22 Step 7 Fit and solder J (shown in red below). Fit and solder J2 (shown in yellow below). J2 must be fitted with the wire access facing the edge of the board. 2

23 Step 8 Remove any solder splats with a brush, such as an old toothbrush. Visually inspect the soldering for dry joints and shorts. Clean the flux off with suitable cleaning materials. Visually inspect again. Before fitting any RC204 modules to the backplane, connect a regulated 5 volt DC power supply to either J or J2. Check the power LED lights when the ON/OFF switch is ON. Check the voltage on resistor R2, at the end nearest the reset switch, is at least 4.5 volts when the reset switch is not pressed, and drops to less than 0.4 volts when the reset switch is pressed. If all is well, power down and plug in some RC204 modules. 22

24 Purchasing the Printed Circuit Board Currently the circuit board is available from Tindie and EasyEDA (in China), or more accurately from their production partner JLCPCB. You can download Gerber files from EasyEDA and send them to your preferred manufacturer, but the following describes the ordering process through EasyEDA. Browse to EasyEDA.com Select the main menu item Explore In the search box, enter RC204 SC6 or sccousins Select, from the list shown, the project SC6 v.x Backplane with PSU The project s details should now be displayed. From here you can select Download Gerber or Order at JLCPCB. You also have the option to Open in Editor a private copy of the schematic or PCB. Selecting Order at JLCPCB requires you to log in (or create an account and log in). Wait for the progress bar to complete. You should now be presented with the image of each side of the board and the following options: Layers 2 Dimensions 02 x 50 mm PCB Qty 0 There is no saving selecting less than 0 PCB Thickness.6 PCB Colour Green You may want to change this to Blue Surface Finish HASL Copper Weight oz Gold Fingers No Material Details FR4-Standard Tg 40C Panel By JLCPCB No Different Design Note, the price increases significantly if you select a colour other than green. Select Save to Cart 23

25 Select Checkout securely Enter your details and select your shipping options. And finally complete the order. 24

26 History v.0 First circuit boards 25

27 Contact Information If you wish to contact me regarding this document, or the hardware and software it relates to, use the contact page at Stephen C Cousins, Chelmsford, Essex, United Kingdom. SC6 information Information about this design can be found at RC204 information Information about the RC204 system can be found at RC204 support Issues related to the RC204 can be posted on the google group RC204-Z80. RC204 supplies Parts can be purchased through Tindie at (search RC204 ) Official RC204 parts are at: 26