DIY Line Tracking Smart Car with AT89C2051

Size: px
Start display at page:

Download "DIY Line Tracking Smart Car with AT89C2051"

Transcription

1 DIY Line Tracking Smart Car with AT89C Introduction: A DIY Smart Car design involves mechanical structure, electronic based sensor principle, automatic control, and even knowledge of microcontroller programming. We hope users can greatly improve their knowledge of electronics, robotics, controls, mechanical, and even soldering technique through hands on practice. We all know that block objects absorb more heat than lighter objects. This Smart Car has infrared receivers which detect signals from infrared emitting diodes. It detects white vs. dark surface, if a darker surface is on the right side, the right motor would stop and vice versa, so the car can always run along a dark trail. With AT89C2051 microcontroller with 2K bytes built in flash memory, this smart car is a very well designed platform which allows different accessories to be added. With innovative thinking it can be converted to fighting robots, remote control cars and so on. As it requires high temperature soldering skill, guardian is required if you are less than 18 years old. Please read through the instruction before start assembling. 2. Things you will learn: Robotics Control How to read electrical schematic How does IR emitter and sensor work How does LM393 use as comparator How does PNP transistor work How does LED work emitting_diode How does Potentiometer work Reading resistor color codes Resistors Improve soldering skill %28Electronics%29 Microcontroller Programming 3. Things that you need but not included with the kit: a. Soldering Iron b. Solder c. Solder Wick (for desoldering) d. Screw Driver e. Digital Multimeter Page 1

2 Contents: Schematic Name Component Value Quantity U1 AT89C U1 IC Socket for AT U2 LM393 1 U2 8pin DIP IC Socket 1 C1 Capacitor C2 Capacitor C3 Capacitor C6 Capacitor 30 1 C7 Capacitor 30 1 C4 Capacitor 100uF 1 C5 Capacitor 100uF 1 D1 LED Green 1 D2 LED Green 1 R1 Resistor 10K 1 R2 Resistor 10K 1 R3 Resistor 10K 1 R4 Resistor 1K 1 R5 Resistor 1K 1 R8 Resistor R9 Resistor R10 Resistor 1K 1 R11 Resistor 1K 1 R12 Resistor 1K 1 R13 Resistor 1K 1 R6 Photoresistor 1 R7 Photoresistor 1 D1, D2 LED Green 2 D3, D4 IR emitter Transparent 2 D5, D6 IR sensor Black 2 Q1, Q2 PNP Transistor M1, M2 Motor 2 S1 Switch 1 J1 J5 Pin 15 Y1 Resonance 12Mhz 1 Wheels 2 Caster Screw 1 Caster Nut 2 Caster 1 Chassis PCB 1 Wire 2 AA Battery Holder 1 Page 2

3 4. Instruction for assembly (Please read through the instruction before start): a. Study the schematic. (can be download from our site) b. Cut the wire into half and solder them on the motors. Soldering Tips: Step1 put solder on the motor. Step2 solder down the wire. c. Assemble the wheels and put them on the motors. d. Populate all the resistors to the according location. e. Populate the DIP sockets. f. Populate the Green LEDs. g. Populate the capacitors and resonance. Page 3

4 h. Populate Q1 and Q2 (Very Important!!! Make sure it is the same as the picture below). i. Populate the pins, potentiometer, and switch (orientation of the switch is not important). j. Turn around the chassis PCB and populate the IR emitters and sensors. Put the LED ~1/2 above the PCB. Page 4

5 k. Stick the battery holder on the PCB, run the wires thru the hole on the PCB and solder the wires accordingly. l. Stick the motor module on the PCB, and solder the wires accordingly. Reserve the wires if the wheel does not turn forward. m. Assemble the wheels, the caster set. 5. Testing: Put the main switch at the OFF position. DO NOT insert LM393 and AT89C2051. Insert the AA batteries. With the switch OFF, use a digital multimeter to measure the current from the switch ON pin to switch Middle pin. If the system is measured much higher than 12mA please double check the connection of all the components. If ~12mA is measured, please insert LM393 IC and measure the current again. The current should now be 1 2mA higher than the previous measurement. If the difference measured is much higher than ~2mA difference, please double check the connection of all the components. If the second measure is correct. You can now insert AT89C2051. Measure the current again with AT89C2051. It should now be 125mA. And this would indicate the system is installed correctly and ready for calibration. 6. Calibration: Insert batteries and turn on the switch. Without influencing IR sensor and detectors, adjust the potentiometers until both wheels are running. Make sure both wheels are running in the correct direction. 7. Troubleshooting: Make sure the IC is installed correctly. Make sure both of the PNP transistors are installed correctly. If D4 or D5 never turns on, first make sure R5 and R6 are soldered correctly, and then you can try to reserve the connection of D4 or D5. If M1 motor runs but D1 diode is not on, first make sure R11 is soldered correctly, and then you can try to reserve the connection of D1. Page 5

6 If M2 motor runs but D2 diode is not on, first make sure R12 is soldered correctly, and then you can try to reserve the connection of D1. For further debugging, examine voltages at the INPUTs of LM Programming: The DIY Smart Car line tracking feature is designed to run with the programmed AT89C2051. No extra programming is needed for line tracking feature. All the useful pins of AT89C2051 are brought out by the pins which are easily access by users. It will be fun to have add on to the Smart Car with AT89C2051. AT89C2051 datasheet is provided. 9. Copyright: In order to design this low cost high value product which benefits lots of people or students, the original designer has spent days and nights to improve and create this new product. We hope the hardwork of the original designer would be respected. We encourage improvement and new ideas. However, direct copying the design is not only theft, but also kills future innovations. Page 6

solutions for teaching and learning

solutions for teaching and learning RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers

More information

Assembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.

Assembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.

More information

solutions for teaching and learning

solutions for teaching and learning Circuit Construction Op-Amp Comparator Project The circuit diagram on the right is the circuit for your project, it is called an op-amp comparator circuit, it is called a comparator circuit as it compares

More information

Schematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)

Schematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel) Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by

More information

TKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: June 20,

TKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: June 20, TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: June 20, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for constructing the TKEY-1A CW touch key Have

More information

AUDIO AMPLIFIER PROJECT

AUDIO AMPLIFIER PROJECT Intro to Electronics 110 - Audio Amplifier Project AUDIO AMPLIFIER PROJECT In this project, you will learn how to master a device by studying all the parts and building it with a partner. Our test subject:

More information

Electronic Coin Toss

Electronic Coin Toss 1 Electronic Coin Toss Why this circuit? This circuit was not designed for people who can make up their mind nor have a coin to use for a heads or tail coin toss. This circuit can also be used to ask it

More information

HUB-ee BMD-S Arduino Proto Shield V1.1

HUB-ee BMD-S Arduino Proto Shield V1.1 HUB-ee BMD-S Arduino Proto Shield V1.1 User guide and assembly instructions Document Version 0.5 Introduction & Board Guide 2 Schematic 3 Quick User Guide 4 Assembly Guide 6 Kit Contents 7 1) Diodes and

More information

Infrared Add-On Module for Line Following Robot

Infrared Add-On Module for Line Following Robot 1 Infrared Add-On Module for Line Following Robot January 3, 2015 Jeffrey La Favre The infrared add-on module allows multiple line following robots to operate on the same track by preventing collisions

More information

Goal: We want to build an autonomous vehicle (robot)

Goal: We want to build an autonomous vehicle (robot) Goal: We want to build an autonomous vehicle (robot) This means it will have to think for itself, its going to need a brain Our robot s brain will be a tiny computer called a microcontroller Specifically

More information

Post Tenebras Lab. Written By: Post Tenebras Lab

Post Tenebras Lab. Written By: Post Tenebras Lab Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.

More information

RKP08 Component List and Instructions

RKP08 Component List and Instructions RKP08 Component List and Instructions PCB layout Constructed PCB RKP08 Scematic RKP08 Project PCB Page 1 Description The RKP08 project PCB has been designed to use PIC microcontrollers such as the Genie

More information

Pacific Antenna Two Tone Generator

Pacific Antenna Two Tone Generator Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination

More information

UF-3701 Power Board Construction Guide

UF-3701 Power Board Construction Guide Page 1/5 Soldering and Part Placement See the Chapter 3 of the MIT 6270 Manual for information on electronic assembly, including soldering techniques and component mounting. Construction Information All

More information

Variable Power Supply Digital Control Circuit Diagram Using Lm317

Variable Power Supply Digital Control Circuit Diagram Using Lm317 Variable Power Supply Digital Control Circuit Diagram Using Lm317 DIGITAL POWER SUPPLY USING LM317 A Major Project Report Submitted partial fulfillment of the requirement for the award of the Degree of

More information

Advanced Strobe 1.0 Kit

Advanced Strobe 1.0 Kit Kit Instruction Manual Eastern Voltage Research, LLC December 2013, Rev 1 1 http://www.easternvoltageresearch.com Kit Introduction to the Kit Thank you for purchasing the Kit. If you are looking for a

More information

Creep Cluster Build Document. V5 - November 2018

Creep Cluster Build Document. V5 - November 2018 Creep Cluster Build Document. V5 - November 2018 Dual triangle oscillators are hard-switched by a fast squarewave. Then the signal goes into a resonant lowpass filter. Sounds vary from deep rumbling drones

More information

TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE

TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05

More information

solutions for teaching and learning

solutions for teaching and learning RKOneAnalogue Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKOneAnalogue Software Development PCB Page 1 Description The RKOneAnalogue software development PCB has been

More information

RC Tractor Guy Controller V2.1 Assembly Guide

RC Tractor Guy Controller V2.1 Assembly Guide RC Tractor Guy Controller V. Assembly Guide Features 0 Push button inputs Dual axis thumb sticks with built-in push button Rotary encoders with built-in push button MCU Socket to suit Meduino Mega 560

More information

You need the following components to assemble the Black n Wood Nixie Clock circuit board:

You need the following components to assemble the Black n Wood Nixie Clock circuit board: You need the following components to assemble the Black n Wood Nixie Clock circuit board: Quantity Designator Description 1 Battery Battery, CR1220 1 Battery Battery holder 3 Button 1, Button 2, Button

More information

EQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.

EQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors. EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about

More information

High Power (15W + 15W) Stereo Amplifier

High Power (15W + 15W) Stereo Amplifier High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit

More information

Thursday, September 15, electronic components

Thursday, September 15, electronic components electronic components a desktop computer relatively complex inside: screen (CRT) disk drive backup battery power supply connectors for: keyboard printer n more! Thursday, September 15, 2011 integrated

More information

Transcendent Frequency Counter

Transcendent Frequency Counter Transcendent Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and operate this frequency counter KIT. Features: The transcendent counter has two input channels

More information

Morse Code Practice Oscillator

Morse Code Practice Oscillator Features Description Keyer speed range: Limited only by keying source True Sine wave tone output Tone Volume Control Tone Frequency Control Internal Speaker 1/8 External Speaker/Headphone Jack RCA Key

More information

Arduino Smart Robot Car Kit User Guide

Arduino Smart Robot Car Kit User Guide User Guide V1.0 04.2017 UCTRONIC Table of Contents 1. Introduction...3 2. Assembly...4 2.1 Arduino Uno R3...4 2.2 HC-SR04 Ultrasonic Sensor Module with Bracket / Holder...5 2.3 L293D Motor Drive Expansion

More information

Number Name Description Notes Image 0101 Resistor, 100 ohm. brown-black-browngold. ¼ watt, 5% tolerance, red-red-brown-gold. brown-black-red-gold.

Number Name Description Notes Image 0101 Resistor, 100 ohm. brown-black-browngold. ¼ watt, 5% tolerance, red-red-brown-gold. brown-black-red-gold. Passive Components 0101 Resistor, 100 brown-black-browngold. 690620 0102 Resistor, 220 red-red-brown-gold. 690700 0103 Resistor, 1000 brown-black-red-gold. 690865 0104 Resistor, 10k 0201 Capacitor, 1 µf,

More information

Part 2: Building the Controller Board

Part 2: Building the Controller Board v3.01, June 2018 1 Part 2: Building the Controller Board Congratulations for making it this far! The controller board uses smaller components than the wing boards, which believe it or not, means that everything

More information

Rapid40i PIC Prototyping PCB User Manual

Rapid40i PIC Prototyping PCB User Manual Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping

More information

Advanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit

Advanced Lantern 1.0 Kit. Introduction to the Advanced Lantern 1.0 Kit Advanced LED Lantern 1.0 Instruction Manual Eastern Voltage Research, LLC Introduction to the Advanced Lantern 1.0 Kit Thank you for purchasing the Advanced Lantern 1.0 Kit. This kit is an advanced microprocessor

More information

Celadon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual

Celadon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual Celadon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual REV 2.1 COPYRIGHT 2001 I. Introduction Thank you for purchasing your infrared remote control transmitter

More information

The PUMPKIN LIGHT LED

The PUMPKIN LIGHT LED The PUMPKIN LIGHT LED PUMPKIN LIGHT LED By Mark McCuller Email: mcculler@mail.com DESIGN SUMMARY The PUMPKIN LIGHT LED By: Mark McCuller The Pumpkin Light LED is a battery-powered device that illuminates

More information

ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003

ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003 ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003 This manual and the circuit described have been brought to you by Adam Blankespoor, Roy Merril, and the number 47. The Problem:

More information

Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article

Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article Images Company Robotic Arm PC Interface allows real time computer control and an interactive script writer/player for programming and

More information

The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.

The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system. Introduction 1 Welcome to the GENIE microcontroller system! The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.

More information

LED Knight Rider. Yanbu College of Applied Technology. Project Description

LED Knight Rider. Yanbu College of Applied Technology. Project Description LED Knight Rider Yanbu College of Applied Technology Project Description This simple circuit functions as a 12 LED chaser. A single illuminated LED 'walks' left and right in a repeating sequence, similar

More information

Casio CZ. Non volatile memory modification Installation instructions version copyright 2013 Artefacts

Casio CZ.   Non volatile memory modification Installation instructions version copyright 2013 Artefacts Casio CZ Non volatile memory modification Installation instructions version 2.0 2017 www.artefacts.nl copyright 2013 Artefacts Introduction The Casio CZ-101 and CZ-1000 do not have a separate backup battery

More information

1. Introduction Packing list Parts Introduction Uno R3 Board for Arduino Specifications... 6

1. Introduction Packing list Parts Introduction Uno R3 Board for Arduino Specifications... 6 Table of Contents Smart Bluetooth Robot Car Kit for Arduino 1. Introduction...4 1.1 Packing list...5 2. Parts Introduction...6 2.1 Uno R3 Board for Arduino...6 2.1.1 Specifications... 6 2.2 HC-SR04 Ultrasonic

More information

VG-305A AC Traffic Light Controller Kit

VG-305A AC Traffic Light Controller Kit Galak Electronics Electronic kits and components Website: GalakElectronics.com Email: sales@galakelectronics.com Phone: (302) 832-1978 VG-305A AC Traffic Light Controller Kit Thank you for your purchase

More information

KPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P

KPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P Devices Included in this Data sheet: KPIC-0818P Features: Carefully designed prototyping area Accepts 8 pin PIC12 series micro-controllers Accepts 14 and 18 Pin PIC16 series Accepts some 8,14 and 18 pin

More information

AC : INFRARED COMMUNICATIONS FOR CONTROLLING A ROBOT

AC : INFRARED COMMUNICATIONS FOR CONTROLLING A ROBOT AC 2007-1527: INFRARED COMMUNICATIONS FOR CONTROLLING A ROBOT Ahad Nasab, Middle Tennessee State University SANTOSH KAPARTHI, Middle Tennessee State University American Society for Engineering Education,

More information

Construction manual. (Almost Ready To Control) Stand , V1.05

Construction manual. (Almost Ready To Control) Stand , V1.05 V.3 ARTC Construction manual V.3 ARTC (Almost Ready To Control) Stand 5.08.206, V.05 Qube Solutions UG (limited liability) Arbachtalstr. 6, 72800 Eningen, GERMANY http://www.qube-solutions.de/ http://

More information

HUB-ee BMD-S Arduino Proto Shield V1.0

HUB-ee BMD-S Arduino Proto Shield V1.0 HUB-ee BMD-S Arduino Proto Shield V1.0 User guide and assembly instructions Document Version 1.0 Introduction 2 Schematic 3 Quick user guide 4 Assembly 5 1) DIP Switches 5 2) Micro-MaTch Connector Headers

More information

LLIA90 LED ARRAY 90 LED Array Illuminator. LLIA90 LED Illuminator Array

LLIA90 LED ARRAY 90 LED Array Illuminator. LLIA90 LED Illuminator Array LLIA90 LED Illuminator Array The LLIA90 is a high-quality and high-performance multi-purpose LED illuminator array. It has a built-in regulator and a photocell control circuit for automatic LED array on/off

More information

Rapid28iXL PIC Prototyping PCB User Manual

Rapid28iXL PIC Prototyping PCB User Manual Description Features This is a PCB designed to facilitate the rapid prototyping of a device based on a 28 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of

More information

Manual Version March 2007

Manual Version March 2007 Manual Version 1.1 - March 2007 Page 1 Table of Contents Section1: 6922 Line Board Build... 3 6922 Line Board Version Notes... 5 6922 Line Board Build - HARD-WIRED VERSION... 5 Final Connections and Checks

More information

Rapid40iXL PIC Prototyping PCB User Manual

Rapid40iXL PIC Prototyping PCB User Manual Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping

More information

Dwarf Boards. DB021 : L298 dual motor driver

Dwarf Boards. DB021 : L298 dual motor driver Dwarf Boards DB021 : L298 dual motor driver (c) Van Ooijen Technische Informatica version 1.0 PICmicro, In-Circuit Serial Programming and ICSP are registerd trademarks of Microchip Technology Inc. Introduction

More information

Digital Flame 1.0 Kit

Digital Flame 1.0 Kit Digital Flame 1.0 Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com Introduction to the Digital Flame 1.0 Kit Thank you for purchasing the Digital

More information

PowerAmp Design. PowerAmp Design EVAL127 EVALUATION KIT FOR PAD127/157. Rev G

PowerAmp Design. PowerAmp Design EVAL127 EVALUATION KIT FOR PAD127/157. Rev G PowerAmp Design EVALUATION KIT FOR PAD7/57 EVAL7 Rev G INTRODUCTION The EVAL7 assembled evaluation kit provides a convenient method to become familiar with the operation of the PAD7/57 operational amplifiers

More information

GPS Series. Build a GPS Smart Logger. By Michael Simpson. As seen in November 2008 of Servo Magazine Pick up an issue at

GPS Series. Build a GPS Smart Logger. By Michael Simpson. As seen in November 2008 of Servo Magazine Pick up an issue at GPS Series By Michael Simpson Build a GPS Smart Logger As seen in November 2008 of Servo Magazine Pick up an issue at www.servomagazine.com I recently did a GPS series covering various GPS modules and

More information

Uzebox Kit Assembly Guide

Uzebox Kit Assembly Guide Uzebox Kit Assembly Guide V1.3 Page 1 of 18 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque

More information

Design Modular Planning

Design Modular Planning Phys253 - Lecture 7, Part II Circuit Components & Layout Design Modular Planning Design by assembling simple circuit modules, such as filters or amplifiers Modules may be separated by buffers, where required

More information

Assembly Instructions IV-11 DCF, melody

Assembly Instructions IV-11 DCF, melody This IV-11 clock is the next generation to the IV-11 Quartz, DCF, melody. This is not a beginner kit. It requires soldering experience on the IV-18 and the IV-3A board The switching power supply wall adapter

More information

BalloonSat Sensor Array

BalloonSat Sensor Array BalloonSat Sensor Array The PICAXE-08M2 in the BalloonSat flight computer is a digital device. Being digital, it functions best with a series of on and off voltages and does not interact very well with

More information

Flight Data Recorder Hardware Version 1.0

Flight Data Recorder Hardware Version 1.0 Flight Data Recorder Hardware Version 1.0 By R. G. Sparber Scope The Flight Data Recorder (FDR) hardware is described here. The software is described in a separate document. The reader can etch their own

More information

RoboSpecies Technologies Pvt. Ltd.

RoboSpecies Technologies Pvt. Ltd. Table of Contents Table of Contents... vi Part 1: Introduction to Robotics... 1 1.1 Robotics... 3 1.1.1 House Robots... 4 1.1.2 Industrial Robots... 4 1.1.3 Medical Robots... 6 1.1.4 Space Robots... 7

More information

Wind Logger Shield. Parts included: Date: 29/07/14 Version: 1.0 By: Matt Little

Wind Logger Shield. Parts included: Date: 29/07/14 Version: 1.0 By: Matt Little Wind Logger Shield Date: 29/07/14 Version: 1.0 By: Matt Little Parts included: This is a simple shield to easily implement a wind resource data logging system. It is designed to read 2 x pulse type anemometers

More information

CP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17

CP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split.  Document revision 2.1 Last modification : 12/11/17 CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge

More information

Figure 1. A complete Temperature Sensor

Figure 1. A complete Temperature Sensor The NearSys Temperature Sensor is a kit that permits a BalloonSat to measure the temperature of the air, interior, or object the sensor itself is placed in contact with. When plugged into a flight computer

More information

Digital Candle 1.0 Kit

Digital Candle 1.0 Kit Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com Introduction to the Kit Thank you for purchasing the Kit. This kit is definitely a favorite

More information

Project Development & Background. Equipment List. DC Power Adapter (9V,2A) Ball Castor 7805 IC L293D IC Breadboard & Jumper wires

Project Development & Background. Equipment List. DC Power Adapter (9V,2A) Ball Castor 7805 IC L293D IC Breadboard & Jumper wires Line Following Robot With Color Detection Authors : Md. Risat Abedin, Faysal Alam, Ajwad Muhtasim Dip Department of Electrical & Electronic Engineering Ahsanullah University of Science & Technology Email:

More information

Laboratory of Sensors Engineering Sciences 9 CFU

Laboratory of Sensors Engineering Sciences 9 CFU Laboratory of Sensors Engineering Sciences 9 CFU Contacts Alexandro Catini catini@ing.uniroma2.it Phone: +39 06 7259 7347 Department of Electronic Engineering First Floor - Room B1-07b Course Outline THEORY

More information

KDS Channel DMX Controlled Servo Kit

KDS Channel DMX Controlled Servo Kit KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an

More information

Onwards and Upwards, Your near space guide Overview of the NearSys Two Sensor Temperature Array Figure 1. A complete Two Sensor Temperature Array

Onwards and Upwards, Your near space guide Overview of the NearSys Two Sensor Temperature Array Figure 1. A complete Two Sensor Temperature Array The NearSys Two Sensor Temperature Array is a kit that permits a BalloonSat to measure two separate temperatures. When plugged into a flight computer like the BalloonSat Mini, the flight computer provides

More information

Uzebox Kit Assembly Guide

Uzebox Kit Assembly Guide Uzebox Kit Assembly Guide V1.7 Page 1 of 21 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque

More information

TA0139 USER MANUAL ARDUINO 2 WHEEL DRIVE WIRELESS BLUETOOTH ROBOT KIT

TA0139 USER MANUAL ARDUINO 2 WHEEL DRIVE WIRELESS BLUETOOTH ROBOT KIT TA0139 USER MANUAL ARDUINO 2 WHEEL DRIVE WIRELESS BLUETOOTH ROBOT KIT I Contents Overview TA0139... 1 Getting started: Arduino 2 Wheel Drive Wireless Bluetooth Robot Kit using Arduino UNO... 1 2.1. What

More information

Figure 3.0, Schematic for display application

Figure 3.0, Schematic for display application Including lighting for model railroad water towers, bridge, runway, running and crossing lights, rolling hardware and storefront dress-up lights are now easy then ever. While there are several kits readily

More information

ROBOT LINE TRACKING MOUSE KIT C-9801

ROBOT LINE TRACKING MOUSE KIT C-9801 ROBOT LINE TRACKING MOUSE KIT TOOLS you'll need Alimentation 4 batteries 1,5 V AA (not included) The mouse is a line follower robot that follows a black line (or any other color) on a white background

More information

MAIN PCB (The small one)

MAIN PCB (The small one) THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed

More information

Quick Guide WARNING: CHOKING HAZARD - Small parts. Not for children under 3 years old. mbot is an educational robot kit for beginners to get hands-on

Quick Guide WARNING: CHOKING HAZARD - Small parts. Not for children under 3 years old. mbot is an educational robot kit for beginners to get hands-on MAKER WORKS TECHNOLOGY INC Technical support: support@makeblock.cc www.makeblock.cc Great tool for beginners to learn graphical programming, electronics and robotics. :@Makeblock : @Makeblock : +Makeblock

More information

AlphaBot2 robot building kit for Arduino

AlphaBot2 robot building kit for Arduino AlphaBot2 robot building kit for Arduino SKU 110060864 Description This AlphaBot2 robot kit is designed to use with an Arduino compatible board UNO PLUS. It features rich common robot functions including

More information

Tubbutec Sumtiple Kit Version Construction Manual

Tubbutec Sumtiple Kit Version Construction Manual Tubbutec Sumtiple Kit Version Construction Manual This document describes the construction of the Sumtiple Kit. The following parts are included: 1x Sumtiple PCB with SMD-Parts already soldered 1x Front

More information

PicoTurbine Mark 8.3 Generator Field Controller Kit

PicoTurbine Mark 8.3 Generator Field Controller Kit PicoTurbine Mark 8.3 Generator Field Controller Kit Based on a design published in Home Power magazine by Richard Perez. Used with permission. Reprint of original article included with kit. An easy-to-build

More information

Storage Card Interface Kit

Storage Card Interface Kit Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3K The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve

More information

µrrc µr/c Robot Controller v1.1

µrrc µr/c Robot Controller v1.1 v1.1 OVERVIEW The µrrc is a simple, easy to use interface between a 3-channel R/C receiver and the OSMC H-Bridge controller for battle style robots. In principle, the µrrc can be used to drive any motor

More information

PICAXE EXPERIMENTER BOARD (AXE090)

PICAXE EXPERIMENTER BOARD (AXE090) (AXE00) Description: The PICAXE experimenter board allows circuits for any size/revision of PICAXE chip ( / / ) to be quickly tested using a prototyping breadboard. The experimenter board provides power

More information

SRI-02 Speech Recognition Interface

SRI-02 Speech Recognition Interface SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.

More information

CHAPTER 5. Voltage Regulator

CHAPTER 5. Voltage Regulator CHAPTER 5 Voltage Regulator In your robot, the energy is derived from batteries. Specifically, there are two sets of batteries wired up to act as voltage sources; a 9V battery, and two 1.5V batteries in

More information

TuBbika SMR-4-PLUS voicecard

TuBbika SMR-4-PLUS voicecard TuBbika SMR-4-PLUS voicecard Assembly instructions We assume you know soldering. If you don t, look first at this tutorial. Be patient! And if you have any doubt, head to the forum never be afraid to ask!

More information

mbot v1.1 - Blue (Bluetooth Version)

mbot v1.1 - Blue (Bluetooth Version) mbot v1.1 - Blue (Bluetooth Version) SKU 110090103 What is mbot? mbot is an all-in-one solution to enjoy the hands-on experience of programming, electronics, and robotics. What is mbot? mbot is an all-in-one

More information

QUANTOM DEFRAKULATOR Build Document last updated june 2018 for PCB version 1.0

QUANTOM DEFRAKULATOR Build Document last updated june 2018 for PCB version 1.0 QUANTOM DEFRAKULATOR Build Document last updated june 2018 for PCB version 1.0 The Quantom Defrakulator is a drone synthesizer with 3 square wave oscillators and one LFO (low frequency oscillator). Each

More information

Background. About this document. After the upgrade

Background. About this document. After the upgrade Table of Contents Background... 3 About this document... 3 After the upgrade... 3 Mounting the Upgrade PCB... 4 Step 1 - Removing the cover... 4 Step 2 - Removing the MSX Audio Bios rom... 4 Step 3 - Remove

More information

MAIN PCB (The small one with the square cut out from one side)

MAIN PCB (The small one with the square cut out from one side) THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed

More information

Figure 1. The Programmable Flight Computer.

Figure 1. The Programmable Flight Computer. The BalloonSat Flight Computer There are 22 parts in this BalloonSat flight computer, the heart of which is the PICAXE- 08M2. The PICAXE is a microcontroller; making the BalloonSat Flight Computer programmable.

More information

AXE Stack 18. BASIC-Programmable Microcontroller Kit. An inexpensive introduction to microcontroller technology for all ability levels

AXE Stack 18. BASIC-Programmable Microcontroller Kit. An inexpensive introduction to microcontroller technology for all ability levels Ltd AXE Stack 18 BASIC-Programmable Microcontroller Kit a division of An inexpensive introduction to microcontroller technology for all ability levels Free Windows interface software Programmable in BASIC

More information

Parts IV-11 DCF melody Date, Weekday, Temperature

Parts IV-11 DCF melody Date, Weekday, Temperature Parts IV-11 DCF melody Date, Weekday, Temperature Parts PSU Parts Bag 1a Power Adapter 12 Volt F1 Bridge / NTC 10R black NTC only for Power Adapter 15 Volt R1 4,7M yellow, violet, green R2 1M brown, black,

More information

3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions

3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions 3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions Version date Author Comments 1.0 29/05/2013 Boris du Reau Initial version Rocket Type Micro-max Model Mid

More information

QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction

QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group. Introduction QRPometer Assembly Manual Copyright 2012 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a QRPometer. We hope you will enjoy building it and and find it a useful addition to

More information

Homework 5: Circuit Design and Theory of Operation Due: Friday, February 24, at NOON

Homework 5: Circuit Design and Theory of Operation Due: Friday, February 24, at NOON Homework 5: Circuit Design and Theory of Operation Due: Friday, February 24, at NOON Team Code Name: Motion Tracking Laser Platform Group No.: 9 Team Member Completing This Homework: David Kristof NOTE:

More information

Exclusive 2.5 GHz Frequency Counter

Exclusive 2.5 GHz Frequency Counter Exclusive 2.5 GHz Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and tune this frequency counter KIT. Features: Frequency range from 5 MHz to 2.5GHz Factory

More information

RFID: Read and Display V2010. Version 1.1. Sept Cytron Technologies Sdn. Bhd.

RFID: Read and Display V2010. Version 1.1. Sept Cytron Technologies Sdn. Bhd. PR8-B RFID: Read and Display V2010 Version 1.1 Sept 2010 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended through suggestion

More information

The Basic Counter. Hobby Electronics Soldering Kit. Instruction Guide

The Basic Counter. Hobby Electronics Soldering Kit. Instruction Guide The Basic Counter Hobby Electronics Soldering Kit Instruction Guide TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required:

More information

Physical Computing Self-Quiz

Physical Computing Self-Quiz Physical Computing Self-Quiz The following are questions you should be able to answer by the middle of the semeter in Introduction to Physical Computing. Give yourself 6.5 points for questions where you

More information

K1EL Morse Code Practice Oscillator CPO

K1EL Morse Code Practice Oscillator CPO Features This is an oscillator not a Morse keyer Input source can be a keyer or straight key Near Sine wave tone output CPO Tone Volume Control CPO Tone Frequency Control Use headphones or external speaker

More information

AAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer

AAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer Fox Delta Amateur Radio Projects & Kits FD- AAZ-0914A AAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer AAZ- 0914A KIT: USB Standalone, Blue tooth standalone and Graphic CPU capable 50MHZ*

More information

[Note: Power adapter is not included in the kits. Users need to prepare a 9 12 V ( >300mA capacity ) DC power supply]

[Note: Power adapter is not included in the kits. Users need to prepare a 9 12 V ( >300mA capacity ) DC power supply] 062 LCD Oscilloscope Assembly Notes Applicable Models: 06203KP, 06204KP DN062-18v02 Important Notes 1. Some components shown in the schematic and PCB layout are for options or adjustments. They do not

More information

Code Practice Oscillator (CPO)

Code Practice Oscillator (CPO) Code Practice Oscillator (CPO) Overview Many thanks for your purchase of this code practice oscillator or CPO, this guide is intended to allow you to quickly get operational. The CPO comprises an approx.

More information

Installation/assembly manual for DCC/Power shield

Installation/assembly manual for DCC/Power shield Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor

More information