User Manual - Network Speed Dome - PD1103Z2-E Quick Start Guide About this Manual This Manual is applicable to PD1103Z2-E Network Speed Dome.

Transcription

1

2 Quick Start Guide About this Manual This Manual is applicable to PD1103Z2-E Network Speed Dome. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website. Please use this user manual under the guidance of professionals. Legal Disclaimer REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. 2

3 Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: /66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. 3

4 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the speed dome. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Please do not look directly into the laser light within 6 meters because laser is hazardous to humans. Cautions Do not drop the dome or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the speed dome in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. 4

5 The dome cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover. Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the speed dome to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the speed dome and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. 5

6 Table of Contents 1 Overview Overview of Type I Speed Dome Overview of Type II Speed Dome Overview of Type III Speed Dome Overview of Type IV Speed Dome Installation Wall Mounting Type I Speed Dome Type II Speed Dome Type III Speed Dome Type IV Speed Dome In-ceiling Mounting Ceiling Mounting Removing the In-ceiling Bracket Wiring For Ceiling Mounting Applications Mounting Setting the Dome over the LAN Wiring Activating the Speed Dome Activation via Web Browser Activation via the Software Modifying the IP Address Accessing via Web Browser

7 1 Overview Please turn the power off before connect the cables. The overview of different speed domes can be categorized into four types, refer to the content below for the details. The cables are distinguished by different colors. The labels attached on the cables are for identification. Type I refers to the 5-inch speed dome. Type II refers to the 6.5-inch speed dome. Type III refers to the 7-inch IR speed dome and7-inch laser speed dome. Type IV refers to the 8-inch IR speed dome and 8-inch laser speed dome. The figures below are for reference only, please refer to the actual product as the standard. 1.1 Overview of Type I Speed Dome BLACK AC24V YELLOW/GREEN RED AC24V 7 8 Figure 1-1 Cable Interface of Type I Speed Dome 1

8 Table 1-1 Descriptions of Cable Interface No. Description 1 Network Cable 2 Audio Cable 3 Alarm Output Cables 4 Alarm Input Cables 5 RS-485 Cables 6 Video Cable 7 Power Cable 8 Micro SD Card Slot 1.2 Overview of Type II Speed Dome 2 types of the 6.5-inch speed dome structure are provided; please refer to the actual product for the location of the SD card slot. RED AC24V YELLOW/GREEN BLACK AC24V Figure 1-2 Cable Interface of the Type II Speed Dome 8 Debug Reset 8 Figure 1-3 SD Card Slot of the Type II Speed Dome 2

9 Table 1-2 Descriptions of Cable Interface No. Description 1 Network Cable 2 Audio Cable 3 Alarm Out 4 Alarm In 5 RS Video Cable 7 Power Cable 8 SD Card Slot 1.3 Overview of Type III Speed Dome SD CA RD 8 Figure 1-4 Cable Interface of the Type III Speed Dome Table 1-3 Descriptions of Cable Interface No. Description 1 Network Cable 2 Audio Cable 3 Alarm Out 4 Alarm In 5 RS-485 3

10 No. Description 6 Video Cable 7 Power Cable 8 SD Card Slot 1.4 Overview of Type IV Speed Dome Figure 1-5 Cable Interface of the Type IV Speed Dome Table 1-4 Descriptions of Cable Interface No. Description 1 Network Cable 2 Video Cable 3 Alarm Out 4 Audio Cable 5 Alarm In 6 RS Power Cable 8 SD Card Slot 9 Head Cover 8 4

11 2 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your speed dome. Make sure all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Make sure that the wall is strong enough to withstand four times the weight of the speed dome and the bracket. For the speed dome that supports IR, you are required to pay attention to the following precautions to prevent IR reflection: Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. Make sure that there is no reflective surface too close to the lens. The IR light from the speed dome may reflect back into the lens causing reflection. Do not drag the speed dome with its waterproof cables as shown in Figure 2-1, otherwise the waterproof performance is affected. Figure 2-1 Do Not Drag the Cables 2.1 Wall Mounting Before you start: Please turn off the power of the speed dome before connecting the cables. 5

12 For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Please make sure that the wall is strong enough to withstand more than 8 times the weight of the dome and the bracket. The bracket in Figure 2-7 is the recommended bracket for this series of speed dome, and a pendent adapter is required if any other bracket is selected Type I Speed Dome The long-arm bracket is taken as the example for following mounting steps. Steps: 1. Loosen the two lock screws on the both side of the speed dome. Pull the lower dome to separate it from the back box as shown in Figure Remove Protective elements. For Separate 5-inch speed dome: Pull the camera module to separate it from the back box, as shown in Figure 2-3. For Integrated 5-inch speed dome: Remove the protective foam, sticker and lens cover from the dome drive. As shown in Figure 2-4. Please do not remove the lock screws from the dome. Back Box Lens Cover Lower Dome Protective Foam Figure 2-2 Remove the Lower Dome 6

13 Figure 2-3 Remove the sticker for separated 5-inch speed dome Figure 2-4 Remove the Sticker for Integrated 5-inch speed dome 3. If the speed dome supports the PoE (Power Over Ethernet) function, you can switch the PoE+ and Hi-PoE function of the dome camera. If the speed dome only supports the power cable, you can skip this step. ON 1 2 Figure 2-5 PoE+ and Hi-PoE Switch 7

14 If you choose Hi-PoE, a Hi-PoE adapter must be connected. Power supply via Hi-PoE is supported. The Hi-PoE module connection is shown below : Power Indicator 2: PORT Indicator 3:DATA&POWER OUT 4: DATA IN 3 4 Network Speed Dome Ethernet Figure 2-6 Hi-PoE Connection Connecting Hi-PoE Steps: 1) Connect the Hi-PoE module to the internet via the DATA IN interface with a network cable. 2) Connect the Hi-PoE module to the speed dome via the DATA & POWER OUT interface with a network cable. 3) Power on the Hi-PoE module. Please power the Hi-PoE module according to its power supply parameters. 4. Align the cuts on the lower dome with the lock screws on the back box to reinstall the lower dome. Tighten the lock screws. 5. Drill 4 screw holes in the wall according to the holes of the bracket, and then insert M8 expansion screws into the mounting holes. 6. Attach the gasket then bracket to the wall by aligning the 4 screw holes of the bracket with expansion screws on the wall. 7. Secure the bracket with 4 hex nuts and washers. 8. Install the speed dome to the bracket. Figure 2-7 Secure the Bracket 8

15 1). Hang the safety rope to the speed dome and the hook on the bracket as shown in Figure ). Route the cables of the speed dome through the bracket. 3). Connect the corresponding cables. Safety Rope Figure 2-8 Hang the Safety Rope 4). Loosen the two lock screws on the bracket. 5). Install the speed dome to the bracket. Rotate the speed dome clockwise tightly. 6). Secure the two lock screws with the Allen wrench. Lock Screw Figure 2-9 Mount the Dome The bracket in Figure 2-7 is the recommended bracket for this series of speed dome, and a pendent adapter is required if any other bracket is selected. See Figure

16 2.1.2 Type II Speed Dome Pendant Adapter Lock Screw Figure 2-10 Pendent Adapter The long-arm bracket is taken as the example for the following mounting steps. Steps: 1. Loosen the 4 lock screws on the flange of the speed dome; refer to the Figure Lock Screws Figure 2-11 Loosen the Lock Screws Please do not remove the lock screws from the dome. 2. Pull the lower dome to separate it from the back box, and remove the protective foam, sticker and lens cover from the dome drive. 10

17 Back Box Lens Cover Lower Dome Sticker Protective Foam Figure 2-12 Remove the Protective Elements 3. Install the micro SD card of the speed dome. Debug Reset SD Card Slot SD Card Slot Open Cover Figure 2-13 Install the SD Card. 4. Align the cuts on the lower dome with the lock screws on the back box to reinstall the lower dome. Tighten the lock screws. 5. Refer to the steps 5-7 of the section to install the bracket. 6. Install the speed dome to the bracket. 1). Hook the back box of the speed dome to the bracket with the safety rope. Route the cables through the bracket. 11

18 2). Connect the corresponding cables. Figure 2-14 Hang the Safety Rope 3). Loosen the two lock screws on the bracket. 4). Install the speed dome to the bracket. Rotate the speed dome clockwise tightly. 5). Secure the two lock screws with the Allen wrench. Lock Screw Figure 2-15 Mount the Dome The bracket in Figure 2-7 is the recommended bracket for this series of speed dome, and a pendent adapter is required if any other bracket is selected. 12

19 Pendant Adapter Lock Screw Figure 2-16 Pendent Adapter Type III Speed Dome Steps: 1. Remove the protective sticker as shown in Figure Protective Sticker Figure 2-17 Remove Protective Sticker 2. Remove the cover on the back of the speed dome as shown in Figure Insert the SD card to the SD card slot and install the cover back. 13

20 SD CARD SD Card Slot Figure 2-18 SD Card Slot 3. Refer to the steps 5-7 of the section to install the bracket. 4. Hook the two ends of the safety rope to the back box of the speed dome and the bracket respectively. Route the cables through the bracket as shown follows. Safety Rope Figure 2-19 Install the Safety Rope 5. Loosen the lock screws on the bracket. 6. Align the speed dome with bracket and rotate it counterclockwise or clockwise to the bracket tightly as shown below. 14

21 Figure 2-20 Install the Speed dome 7. Use L-wrench to tighten the lock screws to secure the speed dome and the bracket. Figure 2-21 Secure the Speed dome 8. Remove the protective film of the IR or laser light after you finish installing. The bracket in Figure 2-7 is the recommended bracket for this series of speed dome, and a pendent adapter is required if any other bracket is selected. See Figure

22 Pendant Adapter Lock Screw Figure 2-22 Pendent Adapter Type IV Speed Dome Steps: 1. Remove the protective sticker as shown in Figure Protective Sticker Figure 2-23 Remove Protective Sticker 2. Remove the cover on the back of the speed dome. Insert the SD card to the SD card slot and install the cover back. 16

23 SD Card Slot Figure 2-24 SD Card Slot 3. Secure the bracket with 4 hex nuts and washers. Figure 2-25 Secure the Bracket 4. Apply thread tape to the thread of the head cover and rotate the head cover to the bracket. Secure the head cover to the bracket with set screws (supplied). 5. Buckle the handle to the safety rope. Figure 2-26 Secure the Head Cover 17

24 + Figure 2-27 Buckle the Handle 6. Hook the two ends of the safety rope to the back box of the speed dome and the bracket respectively. 7. Hitch the speed dome onto the head cover with the hook on the back box. Hook Back Box Figure 2-28 Hang the Speed Dome 8. Route the cables through the head cover and bracket. 18

25 Figure 2-29 Route the Cables 9. Align the back box of the speed dome with the head cover. Use an Allen wrench to tighten the lock screws to secure the speed dome and the bracket. Lock Screw Figure 2-30 Secure the Speed dome 10. Remove the protective film of the IR or laser light after you finish installing. The bracket in Figure 2-25 is the recommended bracket for this series of speed dome, and a pendent adapter is required if any other bracket is selected. 19

26 Pendant Adapter Lock Screw Figure 2-31 Pendent Adapter 2.2 In-ceiling Mounting The in-ceiling mounting is only applicable for the 5-inch indoor speed domes. Before you start: The in-ceiling mounting is applicable to the indoor ceiling construction. The followings are the mandatory precondition for mounting: The height of the space above the ceiling must be more than 250mm. The thickness of the ceiling must ranges from 5 to 40mm. The ceiling must be strong enough to withstand more than 4 times the weight of the dome and its accessories. Steps: 1. Rotate the lower dome counterclockwise to separate it from the back box as shown in Figure Remove the protective lens cover, foam and sticker from the dome drive. 3. Attach lower dome to the back box, and rotate clockwise to secure it. Protective Foam Back Box Lower Dome Protective Sticker Figure 2-32 Remove the Protective Accessory 20

27 4. Drill a hole on the ceiling according to the drill template (supplied). ±2mm of the diameter of the circle is tolerable. Φ224 Figure 2-33 Draw and Cut a Hole on the Ceiling 5. Connect the cables. The video cable, control wire and network cable have been connected to the corresponding interfaces. Connect the power cable and the red LED indicator turns on when the power is on. Please turn the power off after checking the speed dome. 6. Install the speed dome to the ceiling. 1). Loosen the two lock screws on both sides of the back box and make the locks in internal position, as shown in the following figure: Lock Lock Figure 2-34 Locks and Lock Screws 2). Push the speed dome into the mounting hole in the ceiling. 3). Tighten the lock screws with the screwdriver and the locks will automatically rotate outwards to secure the in-ceiling bracket to the ceiling. 21

28 Ceiling Lock Figure 2-35 Install the back box 7. Install the flange. 1). Attach the flange to the lower dome and align the triangular notch of the trim ring with the arrow label on the in-ceiling bracket. 2). After firmly placing the flange to the ceiling, rotate the flange in the direction of arrow to secure it in place. Please remove the protective film on the lower dome after the installation is finished. In order to obtain clear video images, please wear the anti-static gloves when you install the speed dome. Arrow Label Notch Figure 2-36 Install the Flange 2.3 Ceiling Mounting The ceiling mounting is only applicable for the 5-inch indoor speed domes. Before you start: The thickness of the ceiling must ranges from 5 to 40mm. The ceiling must be strong enough to withstand more than 4 times the weight of the dome and its accessories. 22

29 2.3.1 Removing the In-ceiling Bracket The ceiling mounting speed dome is installed with an in-ceiling bracket by default. Before you mount the speed dome on the ceiling, you need to remove the in-ceiling bracket first. Steps: 1. Loosen and remove the 4 screws as shown in following figure (left). And Remove the in-ceiling bracket as shown in following figure (right). Figure 2-37 Remove the Bracket 2. Install 4 bolts to the screw holes as shown in Figure Figure 2-38 Install the bolts Wiring For Ceiling Mounting Applications The cables of dome can be routed either from the top or the side of the back box, as shown in Figure For the cables routed from the top of the back box, it is required to drill a cable hole in the ceiling. 23

30 Figure 2-39 Cabling for Ceiling Mounting Mounting Before you start: If the speed dome is installed to the wooden wall, use the self-tapping screws to secure the mounting base. If the dome is installed to the cement wall, drill three Φ5 screw holes onto the wall according to the position of the holes, and then secure the mounting base to the wall with expansion screws. Steps: 1. Rotate the lower dome counterclockwise to separate it from the back box. Refer to the Figure Remove the protective lens cover, foam and sticker from the dome drive. 4. Attach lower dome to the back box, and rotate clockwise to secure it. 5. Use the mounting base as a template to mark four screw holes onto the ceiling. 6. If you route cables from the top of the back box, mark the cable hole on the ceiling and drill a hole. 7. Secure the mounting base to the ceiling with set screws. Screw Holes Cable Hole Figure 2-40 Secure the Mounting Base 8. Install the speed dome to the mounting base. 1). Route the cables for the speed dome. Align the bottom of the speed dome with the mounting base. 2). Line up the direction of arrow with the spring end of the mounting base. 24

31 3). Push the speed dome upwards and then forwards in the direction of arrow. When the speed dome is placed in position, the spring will automatically snap into the lock clip firmly. Refer to the 0. Push Forwards Line up Push Upwards Figure 2-41 Attach the Back Box to the Mounting Base Please remove the protective film on the lower dome after the installation is finished. Do not touch the bubble of the lower dome directly by hand. The image blurs otherwise. 25

32 3 Setting the Dome over the LAN You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. To ensure the network security of the speed dome, we recommend you to have the speed dome assessed and maintained termly. You can contact us if you need such service. 3.1 Wiring To view and configure the speed dome via LAN (Local Area Network), you need to connect the network speed dome in the same subnet with your PC. Then, install the software or client software to search and change the IP of network speed dome. The following figure shows the cable connection of network speed dome. PC Network Speed Dome Switch Internet NVR Figure 3-1 Wiring over LAN 3.2 Activating the Speed Dome Purpose: You are required to activate the speed dome first by setting a strong password for it before you can use the speed dome. Activation via Web Browser, Activation via software, and Activation via client software are supported. In the following sections, activation via web browser and software will be taken as examples. 26

33 3.2.1 Activation via Web Browser Steps: 1. Power on the speed dome, and connect the speed dome to the network. 2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface. The default IP address of the speed dome is Figure 3-2 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Confirm the password. 5. Click OK to activate the speed dome and enter the live view interface Activation via the Software The software is used for detecting the online device, activating the device, and resetting the password. Get the software from the supplied disk or the official website, and install the software according to the prompts. Follow the steps to activate the speed dome. Steps: 1. Run the software to search the online devices. 2. Check the device status from the device list, and select an inactive device. 27

34 Figure 3-3 Interface 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If activation failed, please make sure that the password meets the requirement and then try again. 3.3 Modifying the IP Address Purpose: To view and configure the speed dome via LAN (Local Area Network), you need to connect the network speed dome in the same subnet with your PC. Then, install the software or client software to search and change the IP of network speed dome. We will take modifying the IP Address via the software as an example to introduce the IP address modification. Steps: 1. Run the software. 2. Click to select an active device. 28

35 Please refer to section 3.2 to activate the speed dome if it is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-4 Modify the IP Address 4. Input the password and click Save to activate your IP address modification. 29

36 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome8 and above version Steps: 1. Open the web browser. 2. In the browser address bar, input the IP address of the network speed dome, e.g., and press the Enter key to enter the login interface. 3. Activate the speed dome for the first time using, refer to the section 3.2 Activating the Speed Dome. 4. Input the user name and password and click. The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions. The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the network speed dome. Please follow the installation prompts to install the plug-in. 30

37 You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. 31

38