DeltaPix M12Z Installation Guide

Size: px
Start display at page:

Download "DeltaPix M12Z Installation Guide"

Transcription

1 1 2 Minimum System Requirements Windows 7 / 8 Microsoft. Both 32 and 64 bit versions of Windows will work. Microsoft dotnet (normally already installed with Windows) 1.3 GHz Pentium III or higher (compatible) 1 GB RAM 5 GB free hard disk space USB 2.0 ports (USB 1 will not work!) System assembling DO NOT CONNECT ANY CABLES TO THE COMPUTER OR CONTROLLER YET Unpack all items (the actual number of parts will depend on specific configuration). Take care not to expose any parts to shock as it will damage the precision mechanics and optics.

2 Attach the track to the base: (standard, might not apply to all configurations) Add the X stage to the plate (any of the two equal stages can be used)

3 Gently turn the stage position manually so you get access to the two holes in each side and use the four enclosed screws to fix the stage. Make sure the stage front is 100% parallel to the front of the bottom plate. Add the Y stage to the top of the X-stage, and fix it in the same way, see the images. Remember that there must be fixed two screws on each side of the stage, four in all for each stage. Make sure the Y stage is attached in precisely 90 degrees angle to the X-stage.

4 If a cover plate for the XY stage and additional sample holder hardware is available, unpack it. See below image with cover plate, manual tilt/rotate stage and universal spring loaded sample holder. Remove the two screws holding the round adapter plate in the center of the Y-stage. Attach the four M6 screws to the cover plate.

5 Mount the rotate/tilt stage to the cover plate by use of one of the enclosed M6 screws. If a universal spring loaded sample holder is also enclosed, unscrew the center screw of the top plate of the rotate/tilt stage, hold the jaw teeth of the sample holder away from each other, in order to mount the sample holder on the stage with the same screw, which was removed. Mount the cover plate on the XY stage by tighten the four M6 screws gently.

6 Now it's time to attach the Z-focus motor to the Z-optics. WARNING: THE Zoom optics is sensitive to shock and make sure not to scratch the objective!!!! First attach the blank adapter plate to the focus motor, if not already done, by means of three of the enclosed M4 screws. Then attach the optics to the adapter plate by use of another three of the enclosed M4 screws. The three screws must be turned a little bit after each other, turning only one all the way, will damage the mechanics. Be patient. Before tightening the screws finally, make sure the adapter is carefully aligned to the Z-motor. After having attached the optics to the Z-motor, it's time to attach it to the stand, but first the adapter plate must be attached to the motor with two M6 screws: (never use screws longer than

7 the enclosed, it will damage the motor!!!), see the image, must be mounted in exactly the same position as shown: Attach the focus motor and optics to the stand by fixing the six enclosed screws. Attach the dome.

8 Attach the track with the zoom optics to the base, by screwing the four enclosed screws into the bottom of the base. Attach the camera to the zoom optics, by firmly screwing the camera onto the C-mount on top of the Zoom optics Attach the enclosed USB2 cable to the camera. (but NOT to the computer at this moment). Attach the enclosed zoom cable to the zoom-optics. Collect the cables from the zoom optic, camera, and focus (Z) motor and fix them with a cable strip (enclosed) as shown here: Collect all cables on the base in the two cable collectors (see image below). Make sure the Y motor cable has enough free cable to move.

9 3 Connect XY stage cables to the of the XY-collector cable, and attach the collector side (15P) to the controller. Connect also the Z and Zoom cables to the controller. NEVER connect or disconnect any cables to the controller while power is on! Connect the light sources, dome light, ring light and /or epi-coaxial light. DO NOT CONNECT ANY USB CABLES TO THE COMPUTER YET. Software Installation prerequisites Before software installation: a. Do not attach any camera or controller to the USB port. b. Do not attach any dongle to the USB port. c. You must be logged on the computer with administrator privileges. Installation procedure - for first time installation Insert the memory stick enclosed with the software package, and double-click on Setup_InSight_A.B.C.exe (the name on the setup program may vary depending on the A.B.C version number). A dialog box like shown to the right will appear. Follow the onscreen prompts to install the software: Application software, drivers for cameras, the.net framework and all needed software will be installed. Always click Next or Install. One exception from this is the dongle driver installation, like shown below, where you must click Close.

10 When all installation is complete, click Finish. After the software has been installed, plug the USB 2.0 Camera into a USB 2.0 High-Speed port. For Windows Vista and Windows 7 / 8 a. 4 Installation procedure - Reinstallation or Update 5 6 The hardware installation is done automatically and almost silently. It can take several minutes until it's finished. The installation software will automatically detect if a previous installation is present and automatically uninstall it before installing new software. If you are installing a software update downloaded from our website, please save the setup file in a directory of your choice and run it from there. Follow the instructions as Installation procedure - for first time installation Dongle Attach the dongle now (the green USB device), and let the hardware install. DeltaStep4 controller driver installation Download the appropriate compressed driver file CP210x_VCP_Windows.zip. The file can be downloaded from here: Extract the CP210x_VCP_Windows.zip file to a convenient directory, and run either CP210xVCPInstaller_x86 if your computer runs as 32bit CP210xVCPInstaller_x64 if your computer runs as 64bit Follow the prompts. When software installation is complete, attach the USB cable to the controller no need to attach power yet. Windows will announce that new hardware has been found, and will install the driver with little or no interaction required from you.

11 The device will install as Silicon Labs CP210x you can also check this in the Device Manager. You should end up having a virtual COM port, please remember the COM port number. In the below example the port is COM3, DeltaStep4 controller 1. Attach the power supply to V and connect the 12V output cable to the controller 12V input. 2. Push the power on switch on the controller unit. Before Software start for the first time Attach the dongle now (the green USB device), and let the hardware install. Software start for the first time Start the application software. If this is the first time the software runs on your computer, a Quick System Configuration tool will show up. This allows easy set up of most things, e.g. for a Modus12Z system, and may save you a lot of time.

12 The Quick System Configuration shows up if the application: is run for the first time ever a new version of the application is run for the first time. If you do not want to use the tool, simply click Cancel, else Click Next >. Select the system that best matches your configuration. This example selects a Modus 12Z system. Click Next >. The application needs to know the COM port to use. The Modus12Z uses a DeltaStep4 controller that installs as a Silicon Labs CP210x. Select the associated COM port. Click Next >.

13 Maybe your system has been precalibrated at the factory, and calibration files delivered on a USB stick. If you want to load these calibration files, check the Load Calibration Files checkbox. Click Next >. To load the calibration files, navigate to the directory on e.g. the USB stick. Select the directory, click OK. The Optics Editor shows up with the new calibration you may close this now. The configuration is complete. Click Next >. Probably the application needs to be restarted it will then automatically close. Please start it again. Note: The Quick System Setup can be manually launched at any time by the shortcut Ctrl-ShiftW.

14 10 Calibrating the System In case your motorized zoom needs to be recalibrated (normally this is not needed!) put it in the highest magnification position (10x). Then carefully do a calibration as if it was a normal manual objective with a 1x objective. See the InSight manual for a detailed guide. 11 User guide The use of the M12Z system is covered by the general user manual for the InSight software. The manual is included on the memory stick enclosed with the system. Latest version can always be downloaded directly from within the program in the "file/help.." menu-tab.

DeltaPix Prior ES10ZE Installation Guide

DeltaPix Prior ES10ZE Installation Guide 1 Minimum System Requirements Windows XP (Service Pack 2), Windows Vista or Windows 7 with Microsoft. Both 32 and 64 bit versions of Windows will work. ".NET 3.5" (enclosed on the DeltaPix software memory

More information

Lab - Manage Virtual Memory in Windows 7 and Vista

Lab - Manage Virtual Memory in Windows 7 and Vista Lab - Manage Virtual Memory in Windows 7 and Vista Introduction In this lab, you will customize virtual memory settings. Recommended Equipment A computer with Windows 7 or Vista installed The hard drive

More information

CipherLab Workstation Setup (Windows 7/8/10)

CipherLab Workstation Setup (Windows 7/8/10) CipherLab Workstation Setup (Windows 7/8/10) These installation instructions will step you through setting up the CipherLab docking cradle and device, as well as installing the drivers and software used

More information

DeltaPix Modus M12Z Digital microscope

DeltaPix Modus M12Z Digital microscope DeltaPix Modus M12Z Digital microscope DeltaPix Modus 12Z Compact Full This innovative fully motorized and automated digital microscope offers quality and features never seen before at this price level.

More information

Watt Pilot Motorized Attenuator. Quick Start Guide

Watt Pilot Motorized Attenuator. Quick Start Guide Watt Pilot Motorized Attenuator Quick Start Guide Introduction Package This guide is designed to help you quickly install Watt Pilot. When connected to a host computer (operating system Windows 98 or further

More information

FS-IP3000-M User Manual. Ver 1.0

FS-IP3000-M User Manual. Ver 1.0 FS-IP3000-M User Manual Ver 1.0 Sentry360 2014 Table of Contents 1. Overview... 3 1.1 Features... 3 1.2 Package Contents... 4 1.3 Dimensions... 5 1.4 Installation... 6 1.5 Connectors... 7 2. Connect Ethernet

More information

Dell EMC Repository Manager Version 3.1. Quick Start Guide

Dell EMC Repository Manager Version 3.1. Quick Start Guide Dell EMC Repository Manager Version 3.1 Quick Start Guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates

More information

Installation Instructions

Installation Instructions Installation Instructions Casting Simulation Software Version 3.2 for Windows XP and Windows Vista Version 2009-03-24 Installation and Licensing Upgrading Existing FLOW-3D Cast Installation 1) Copy FLOW-3D

More information

Setting up the PC ready for BESA 11

Setting up the PC ready for BESA 11 Setting up the PC ready for BESA 11 1 - Installing Driver. Important Note: Before you start to install the driver, please do not plug BESA 11 into the computer s USB port or else the installation will

More information

Instruction Install DPV for SWEET

Instruction Install DPV for SWEET Content 1 System requirements... 2 1.1 Operating system... 2 1.2 Minimal system requirements... 2 1.2.1 Client... 2 1.2.2 Server... 2 1.3 Prerequisites... 2 1.4 Techniques used... 3 2 Installing DPV...

More information

FTRESTORE. Yaesu FT Radio Configuration Restore Utility

FTRESTORE. Yaesu FT Radio Configuration Restore Utility FTRESTORE Yaesu FT Radio Configuration Restore Utility VK2BYI FTRestore is a Windows desktop application designed to upload, download and compare memory channels and menu settings in the Yaesu FTDX1200

More information

Removal and Installation8

Removal and Installation8 8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever

More information

ColorMaxLP Label Roll Rewinder

ColorMaxLP Label Roll Rewinder ColorMaxLP Label Roll Rewinder 5/2017 INSTALLATION/OPERATOR MANUAL Included: Rewinder Base plate Power supply Power Cord Thumb screws Assembly instructions 1. Install base plate Lift front of printer and

More information

Macro View All in One Scope Description. 2. Features. 3. Package Contents

Macro View All in One Scope Description. 2. Features. 3. Package Contents Macro View All in One Scope 26700-104-00 1. Description Portable system ideal for inline use This self-contained video inspection system is a compact unit, that simplifies quality checks at any stage of

More information

Rue Gurnigel 48 CH-2501 Bienne Tél.: +41 (0) Fax: +41 (0)

Rue Gurnigel 48 CH-2501 Bienne Tél.: +41 (0) Fax: +41 (0) OPTISCHE MESSTECHNIK OPTICAL MEASURING SYSTEMS SYSTEMES DE MESURE OPTIQUE marcel - aubert - sa Rue Gurnigel 48 CH-2501 Bienne Tél.: +41 (0)32 365 51 31 Fax: +41 (0)32 365 76 20 E-mail: info@marcel-aubert-sa.ch

More information

Sound Card Installation for Windows 95/98

Sound Card Installation for Windows 95/98 Sound Card Installation for Windows 95/98 Hardware Installation 1. Shut down Windows and power down system. Unplug power cable from the system. 2. Remove screws and open system enclosure. 3. Remove static

More information

AstroJet L1 Quick Start Guide

AstroJet L1 Quick Start Guide AstroJet L1 Quick Start Guide Step 1 Remove Printer and Accessories from packaging Place Printer on a level, stable surface. Make sure Printer is level. Step 2 Install Ink Drip Tray Assembly 1. Open Ink

More information

Virtual COM Port Driver Installation Manual

Virtual COM Port Driver Installation Manual Virtual COM Port Driver Installation Manual Installing the virtual COM port driver software on a computer makes possible CAT communication via a USB cable to the FTDX3000 series transceiver. This will

More information

WA1937 WebSphere Portal 7.0 Programming. Classroom Setup Guide. Web Age Solutions Inc. Copyright 2012 Web Age Solutions Inc. 1

WA1937 WebSphere Portal 7.0 Programming. Classroom Setup Guide. Web Age Solutions Inc. Copyright 2012 Web Age Solutions Inc. 1 WA1937 WebSphere Portal 7.0 Programming Classroom Setup Guide Web Age Solutions Inc. Copyright 2012 Web Age Solutions Inc. 1 Table of Contents Part 1 - Minimum Hardware Requirements...3 Part 2 - Minimum

More information

MeshConnect ISP / WNA (ZIC2410USB-WNA-1) User Guide

MeshConnect ISP / WNA (ZIC2410USB-WNA-1) User Guide MeshConnect Family MeshConnect ISP / WNA (ZIC2410USB-WNA-1) User Guide 0007-05-08-06-001 (REV B) TABLE OF CONTENTS INTRODUCTION 3 CEL MESHCONNECT ISP / WNA FEATURES 3 GETTING STARTED 4 USB SETUP 4 MESHCONNECT

More information

IT Essentials v6.0 Windows 10 Software Labs

IT Essentials v6.0 Windows 10 Software Labs IT Essentials v6.0 Windows 10 Software Labs 5.2.1.7 Install Windows 10... 1 5.2.1.10 Check for Updates in Windows 10... 10 5.2.4.7 Create a Partition in Windows 10... 16 6.1.1.5 Task Manager in Windows

More information

9936A LogWare III. User s Guide. Revision

9936A LogWare III. User s Guide. Revision 9936A LogWare III User s Guide Revision 850701 Table of Contents 1 Introduction...1 1.1 Symbols Used... 1 1.2 Conventions... 1 1.3 What is LogWare?... 1 1.4 License Agreement... 2 1.5 Requirements...

More information

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the

More information

AstroJet S1 Quick Start Guide

AstroJet S1 Quick Start Guide AstroJet S1 Quick Start Guide Step 1 Remove Printer and Accessories from packaging Place Printer on a level, stable surface. Make sure Printer is level. Step 2 Assemble Ink Drip Tray Assembly 1. Select

More information

IS-DM220/IR/HB IS-DM220

IS-DM220/IR/HB IS-DM220 IS-DM220/IR/HB IS-DM220 Installation Guide Indoor/Outdoor Ver. 1.2 00P6NX223ZXSEA2 Table of Contents 1. Indoor Camera Installation... 3 1.1 Hard Ceiling... 3 1.2 In-Ceiling (T-Bar) Mounting... 13 1.3 4S

More information

REMOTE HEAD ADAPTER INSTALLATION GUIDE

REMOTE HEAD ADAPTER INSTALLATION GUIDE REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and

More information

Lab 4: Trajectory Following 1

Lab 4: Trajectory Following 1 Lab 4: Trajectory Following 1 Prelab Familiarize yourself with how the LabVIEW program works It is XYposition_control1.4.vi Located in Lab4_LabVIEW.zip on the Stellar page 2 Optional prelab: create your

More information

Dell EMC Repository Manager Version 3.2. Quick Start Guide

Dell EMC Repository Manager Version 3.2. Quick Start Guide Dell EMC Repository Manager Version 3.2 Quick Start Guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates

More information

WA1685 WebSphere Portal v6.1 Programming. Classroom Setup Guide. Web Age Solutions Inc. Web Age Solutions Inc

WA1685 WebSphere Portal v6.1 Programming. Classroom Setup Guide. Web Age Solutions Inc. Web Age Solutions Inc WA1685 WebSphere Portal v6.1 Programming Classroom Setup Guide Web Age Solutions Inc. Web Age Solutions Inc. 2011 1 Table of Contents Part 1 - Minimum Hardware Requirements...3 Part 2 - Minimum Software

More information

3 Indoor Dome. Mounting on the Wall with Gang Box (Face Forward) Installation Guide. For Models: D5x / E5x / TCM-3xxx 2014/01/16

3 Indoor Dome. Mounting on the Wall with Gang Box (Face Forward) Installation Guide. For Models: D5x / E5x / TCM-3xxx 2014/01/16 3 Indoor Dome Mounting on the Wall with Gang Box (Face Forward) Installation Guide For Models: D5x / E5x / TCM-3xxx 2014/01/16 Table of Contents Installation Procedures... 3 Step 1: Install the Gang Box...

More information

REMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.

REMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right

More information

Operation manual. IC-Scanner FLS 102. Copyright April 2008 LANGER EMV-Technik GmbH IC-Scanner FLS 102/0214

Operation manual. IC-Scanner FLS 102. Copyright April 2008 LANGER EMV-Technik GmbH IC-Scanner FLS 102/0214 Operation manual IC-Scanner FLS 102 Copyright April 2008 LANGER EMV-Technik GmbH /0214 Fon: +49 351 430093-0 2 Table of contents 1. Measurement setup... 3 1.1 Safety instructions... 3 1.1.1 Safety precautions...3

More information

Fleet Manager 2002 Professional Network Configuration Guide

Fleet Manager 2002 Professional Network Configuration Guide Handling a complex world. Fleet Manager 2002 Professional Network Configuration Guide Overview The VDO Fleet Manager Professional utilises an advanced three-tier client-server model and is designed to

More information

RMX 2000 MPM to MPM+ Migration Procedure

RMX 2000 MPM to MPM+ Migration Procedure RMX 2000 MPM to MPM+ Migration Procedure When upgrading from version 2.x/3.x or 4.0.x, the migration procedure involves two main steps: Upgrading from version 2.x/3.x to version 4.1.1 (described in this

More information

COGNEX. DataMan 100 Verifier. Quick Reference Guide

COGNEX. DataMan 100 Verifier. Quick Reference Guide COGNEX DataMan 100 Verifier Quick Reference Guide 1 Hardware Installation Kit Contents Overview Install the 16mm Lens Mount the Reader Set Lighting Angle Install Software and Connect the DataMan 100 Verifier

More information

Set-Up Instructions. Set-Up Instructions. Unpack the machine and its components.

Set-Up Instructions. Set-Up Instructions. Unpack the machine and its components. Set-Up Instructions Thank you for purchasing the Canon FAXPHONE L80. To get your machine ready for use, please follow the instructions in this document before referring to any other documentation. Unpack

More information

Agilent ICP-OES SVS 2 Productivity Package Installation and Upgrade Instructions

Agilent ICP-OES SVS 2 Productivity Package Installation and Upgrade Instructions Agilent ICP-OES SVS 2 Productivity Package Installation and Upgrade Instructions NOTICE: This document contains references to Varian. Please note that Varian, Inc. is now part of Agilent Technologies.

More information

INSTALLATION GUIDE FOR UBI SENSOR FRAME

INSTALLATION GUIDE FOR UBI SENSOR FRAME INSTALLATION GUIDE FOR UBI SENSOR FRAME Ubi Interactive Inc. Contents INTRODUCTION... 2 WHAT IS IN THE PACKAGE... 2 HOW TO SET UP HARDWARE... 2 INTERACTION... 6 SETTING UP UBI APPS... 7 INTRODUCTION Ubi

More information

Installing TAM Air Assistant Software TM

Installing TAM Air Assistant Software TM Installing TAM Air Assistant Software TM Installation Instructions This document describes how to make a new installation of TAM Air Assistant. TAM Air Assistant is intended to be installed on a PC running

More information

GP-N100 Utility Software Manual

GP-N100 Utility Software Manual System Requirements En Thank you for your purchase of a GP-N100. This manual describes how to use the GP-N100 Utility to download the latest assisted GPS data from Nikon servers to your GP-N100. To ensure

More information

Panowin F1. User Manual

Panowin F1. User Manual Panowin F1 User Manual 1 PANOWIN TECHNOLOGIES CO.,LTD. WARNING power outlet. CAUTION: In case of emergency unplug the Panowin F1 from the WARNING: Carefully monitor the Panowin F1 during operation. Do

More information

2.2. Facilities Requirements

2.2. Facilities Requirements 2.2. Facilities Requirements Facilities requirements for the alpha-se system are listed in Table 2-1 and the system dimensions are given in Figure 2-1. As shown in Figure 2-2, the preferred clear work

More information

Start Here. Important setup information. Remove all tape and lift display. Locate components

Start Here. Important setup information. Remove all tape and lift display. Locate components Start Here 1 Important setup information Wireless or wired network users: you must follow the instructions in this setup guide to be successful adding the HP All-in-One to your network. USB cable users:

More information

5020S CR READER. Software Installation Guide & Calibration Process. Ver.: Document Part Number: CR /170208

5020S CR READER. Software Installation Guide & Calibration Process. Ver.: Document Part Number: CR /170208 5020S CR READER Software Installation Guide & Calibration Process Ver.: 040608 Document Part Number: CR 11072220/170208 - 2 - CR-Tech is marketing the 5020s, an innovation in the field of compact desktop

More information

Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz

Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz Power Mac and Operating System Compatibility This Encore/ST G4 Duet processor upgrade card is compatible only with Power Mac G4 AGP Graphics, Gigabit

More information

A-100G6 - Basic frame assembly diagram

A-100G6 - Basic frame assembly diagram doepfer System A - 100 Rack system A-100 G A-100G6 - Basic frame assembly diagram Parts: 1 Rail with lip, and with tapped hole strip inserted (with M3 threads). 2 Rail with lip, with three M3 hexagon nuts

More information

Remote Deposit Service

Remote Deposit Service Remote Deposit Service Start Up Guide *Screen shots are shown for illustrative purposes only and may vary based on the version of Windows you are currently using. Step 1: Confirm your PC meets system

More information

xponent Version 4.2 RELEASE NOTES

xponent Version 4.2 RELEASE NOTES xponent Version 4.2 RELEASE NOTES Copyright Luminex Corporation, 1996-2013. All rights reserved. Part Number: 89-30000-00-462 Disclaimer Subject to change without notice. Although prepared to ensure accuracy,

More information

Dome C3i Digital Flat-Panel Display Dome DX2/PCI Display Controller Dome CXtra Software QUICK REFERENCE. Windows XP Windows 2000

Dome C3i Digital Flat-Panel Display Dome DX2/PCI Display Controller Dome CXtra Software QUICK REFERENCE. Windows XP Windows 2000 America Sales Planar Systems, Inc. 1195 NW Compton Drive Beaverton, OR 97006-1992 USA phone + 1 (503) 748-1100 fax + 1 (503) 748-1493 Medical Sales Planar Systems, Inc. 400 Fifth Avenue Waltham, MA 02451-8738

More information

WA1973 IBM Business Process Manager 8.0 Programming Using IBM Integration Designer. Classroom Setup Guide. Web Age Solutions Inc.

WA1973 IBM Business Process Manager 8.0 Programming Using IBM Integration Designer. Classroom Setup Guide. Web Age Solutions Inc. WA1973 IBM Business Process Manager 8.0 Programming Using IBM Integration Designer Classroom Setup Guide Web Age Solutions Inc. Web Age Solutions Inc. 1 Table of Contents Part 1 - Minimum Hardware...3

More information

Pan-Tilt-Zoom Security Camera

Pan-Tilt-Zoom Security Camera Security Made Smarter Pan-Tilt-Zoom Security Camera For use with Swann Pro-Series 080p DVRs EN INSTRUCTION MANUAL M080VERE Swann 07 7 5 8 6 4 VIDEO INPUT 4 INPUT OUTPUT VGA RS485 LAN V Step One - Introduction

More information

Version 6.3 Upgrade Guide

Version 6.3 Upgrade Guide Version 6.3 Upgrade Guide Copyright 2016 Manufacturing Information Systems, Inc. 217-4 Maxham Meadow Way Woodstock, Vermont 05091 MISys and the MISys logo are registered trademarks of Manufacturing Information

More information

Quick Installation Guide

Quick Installation Guide Quick Installation Guide WAP-EN1750C AC1750 Ceiling Mount Access Point I. I Product Information I-1. Package Contents 1 2 5 6 3 4 7 1. Access Point 5. Quick Installation Guide 2. Ceiling Mount Bracket

More information

ProtoCOL 3 Software Installation - Quick Guide

ProtoCOL 3 Software Installation - Quick Guide ProtoCOL3 Software Installation Quick Guide ProtoCOL 3 Software Installation - Quick Guide 1 Start PC Log onto PC as an Administrator and shut all running software down 2 Insert the Synbiosis USB flash

More information

MantraJet 1100 CD/DVD autoprinter Operator s manual

MantraJet 1100 CD/DVD autoprinter Operator s manual MantraJet 1100 CD/DVD autoprinter Operator s manual Rev 1.00 May 7, 2008 Table of contents 1. Specifications.. Page 2 2. Unpacking you MantraJet 1100 Page 3 3. Using your autoprinter for the first time.

More information

AstroJet TM M2 Quick Start Guide

AstroJet TM M2 Quick Start Guide AstroJet TM M2 Quick Start Guide Step 1 Remove Printer and Accessories from packaging. Place Printer on a flat, even surface. Step 2 Remove Service Station Transport Tab 1. Open Top Cover. 2. Open Print

More information

SGC2910. User manual

SGC2910. User manual SGC2910 User manual Contents Introduction........................................................ 3 System Requirements................................................. 3 Product Features.....................................................

More information

Manual for MantraJet 1100 CD/DVD auto-printer

Manual for MantraJet 1100 CD/DVD auto-printer Manual for MantraJet 1100 CD/DVD auto-printer Rev 1.03 September 7, 2010 Table of contents Specifications...3 Unpacking MantraJet 1100...4 Quick installation reference MantraJet 1100...7 Installation of

More information

IRF90 - Rotating Focuser

IRF90 - Rotating Focuser IRF90 - Rotating Focuser Part # 600180 REV092111 Page 1 Contents Introduction and Overview... 3 Limitations... 3 Packing List... 4 Installation... 5 Remove Existing Focuser... 5 Installing the Rotating

More information

FS-IP6360-V User Manual. Ver 1.0

FS-IP6360-V User Manual. Ver 1.0 FS-IP6360-V User Manual Ver 1.0 Sentry360 2016 Table of Contents 1. Overview...3 1.1 Features... 3 1.2 Package Contents... 4 1.3 Dimensions... 5 1.4 Installation... 6 1.5 Function Cables... 7 1.6 Connectors...

More information

EN-CAUH-B. Enclosure. Assembly Guide

EN-CAUH-B. Enclosure. Assembly Guide Assembly Guide 1 Note: *To reduce static discharge, do not assemble while on a carpeted surface. *Handle hard drives on the sides only. Do not touch any pins or connectors. * does not have an esata Connection

More information

Installation of Hot Disk v 7.3 and later on a PC with Windows 7, 8 or 10

Installation of Hot Disk v 7.3 and later on a PC with Windows 7, 8 or 10 Installation Instruction for Hot Disk TPS 7 2.1 2017-05-09 1(44) Installation of Hot Disk v 7.3 and later on a PC with Windows 7, 8 or 10 Installation Instruction for Hot Disk TPS 7 2.1 2017-05-09 2(44)

More information

TEL-218DRV TEL-X-Driver

TEL-218DRV TEL-X-Driver TEL-218DRV TEL-X-Driver TEL-Atomic, Incorporated P.O. Box 924 Jackson, MI 49204 1-800-622-2866 FAX 1-517-783-3213 email: telatomic@mindspring.com website: www.telatomic.com Features Angular Resolution:

More information

IS-BX-12 User Manual

IS-BX-12 User Manual IS-BX-12 User Manual Ver 1.0 Sentry360 2014 Table of Contents 1. Overview...3 1.1 Features... 3 1.2 Package Contents... 4 1.3 Dimensions... 4 1.4 Connectors... 5 1.5 Light Sensor... 6 2. Camera Cabling...6

More information

UP! Quick Start Guide

UP! Quick Start Guide Personal Portable 3D Printer UP! www.pp3dp.com 1. Assemble Printer Open the box, take out the printer and accessories. Assemble the parts contained in the box as following procedure: 1. Unscrew the M4

More information

WA2402 Introduction to Responsive Web Development with HTML5, CSS3, JavaScript and jquery. Classroom Setup Guide. Web Age Solutions Inc.

WA2402 Introduction to Responsive Web Development with HTML5, CSS3, JavaScript and jquery. Classroom Setup Guide. Web Age Solutions Inc. WA2402 Introduction to Responsive Web Development with HTML5, CSS3, JavaScript and jquery Classroom Setup Guide Web Age Solutions Inc. Copyright Web Age Solutions Inc. 1 Table of Contents Part 1 - Minimum

More information

DataNet Installation Guide + Quick Start Guide Updated: August 2008

DataNet Installation Guide + Quick Start Guide Updated: August 2008 DataNet Installation Guide + Quick Start Guide Updated: August 2008 This document contains instructions for downloading and installing the DataNet software, supporting Fourier Systems DataNet data logging

More information

9936A LogWare III. User s Guide. Revision

9936A LogWare III. User s Guide. Revision 9936A LogWare III User s Guide Revision 680301 Table of Contents 1 Introduction... 1 1.1 Symbols Used...1 1.2 Conventions...1 1.3 What is LogWare?...1 1.4 License Agreement...2 1.5 Requirements...2 1.6

More information

WA2087 Programming Java SOAP and REST Web Services - WebSphere 8.0 / RAD 8.0. Classroom Setup Guide. Web Age Solutions Inc. Web Age Solutions Inc.

WA2087 Programming Java SOAP and REST Web Services - WebSphere 8.0 / RAD 8.0. Classroom Setup Guide. Web Age Solutions Inc. Web Age Solutions Inc. WA2087 Programming Java SOAP and REST Web Services - WebSphere 8.0 / RAD 8.0 Classroom Setup Guide Web Age Solutions Inc. Web Age Solutions Inc. 1 Table of Contents Part 1 - Minimum Hardware Requirements...3

More information

SOFTWARE INSTRUCTIONS DIGITAL SPEAKER PROCESSOR DP-SP3

SOFTWARE INSTRUCTIONS DIGITAL SPEAKER PROCESSOR DP-SP3 SOFTWARE INSTRUCTIONS DIGITAL SPEAKER PROCESSOR DP-SP3 Thank you for purchasing TOA s Digital Speaker Processor. Please carefully follow the instructions in this manual to ensure long, trouble-free use

More information

SATA 150 PCI Card 2-Channel

SATA 150 PCI Card 2-Channel SATA 150 PCI Card 2-Channel User Manual Ver. 1.00 All brand names and trademarks are properties of their Respective owners. 1 Features Silicon Image SiI3512 SATA controller chip Compliant with PCI Specification,

More information

HANDBOOK FOR THE MOBYL DATA CENTER 22

HANDBOOK FOR THE MOBYL DATA CENTER 22 HANDBOOK FOR THE MOBYL DATA CENTER 22 1 For support contact us at support@addc.net www.addc.net 516.673.4444 1983 Marcus Ave. Suite 104 Lake Success, NY 11042 HANDBOOK FOR THE MOBYL DATA CENTER 22 TABLE

More information

LUM-500-PTZ IP Surveillance Camera. Installation and Quick Start Guide

LUM-500-PTZ IP Surveillance Camera. Installation and Quick Start Guide LUM-500-PTZ IP Surveillance Camera Installation and Quick Start Guide Read this before you go on site! For maximum control and convenience, install your camera with a connection to the Internet via your

More information

Microscopic Imaging Research Station (MIRS) Assembly Guide. Version 1.0.0

Microscopic Imaging Research Station (MIRS) Assembly Guide. Version 1.0.0 Microscopic Imaging Research Station (MIRS) Assembly Guide www.adsyscontrols.com Adsys Controls, Inc.2012 Version 1.0.0 I. Assembly of the Adsys Controls MIRS system This document explains the assembly

More information

Product User Guide. OctProcessV2 and QuadProcessV2. QuadProcessV2-3A 4-Channel Low Level DC Current

Product User Guide. OctProcessV2 and QuadProcessV2. QuadProcessV2-3A 4-Channel Low Level DC Current OctProcessV2-3A 8-Channel Low Level DC Current OctProcessV2-30mA 8-Channel Low Level DC Current OctProcessV2-160mA 8-Channel Low Level DC Current QuadProcessV2-3A 4-Channel Low Level DC Current QuadProcessV2-30mA

More information

Clone an Existing Drive

Clone an Existing Drive Clone an Existing Drive This guide will go through the process of cloning your existing software, OS, and data to a new hard drive. Written By: Mike ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION

More information

The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter.

The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter. The printer kit 556-00239 contains a TT230SM printer without cutter. The printer kit 556-00256 contains the TT230SMC printer with cutter. The cutter is required if printing and cutting HellermannTyton

More information

Rostock Cornea Module. Heidelberg Retina Tomograph 3. Installation Instructions

Rostock Cornea Module. Heidelberg Retina Tomograph 3. Installation Instructions Rostock Cornea Module Heidelberg Retina Tomograph 3 Installation Instructions Revision 1.3-1E, June 2006 Heidelberg Engineering GmbH 2006 Printed in Germany Art. No. 11223 / 97 085-002 The manufacturer

More information

Afinia Label L901 Label Printer Quick Start Guide

Afinia Label L901 Label Printer Quick Start Guide Afinia Label L901 Label Printer Quick Start Guide Ver. 1.1 Page 2 Step 1 Remove Printer and Accessories from packaging Items included: Printer USB cable One ink set (CMYKK) Quick Start Guide Network cable

More information

Paramount Electronics Replacement Instructions

Paramount Electronics Replacement Instructions Paramount Electronics Replacement Instructions Revision 1.7, October 2017 2017 Software Bisque, Inc. All rights reserved. Contents Replacing Paramount Electronics... 3 Step 1: Save Existing Control System

More information

WA1787 Designing and Developing Higher Performance Web Services. Classroom Setup Guide. Web Age Solutions Inc. Copyright Web Age Solutions Inc.

WA1787 Designing and Developing Higher Performance Web Services. Classroom Setup Guide. Web Age Solutions Inc. Copyright Web Age Solutions Inc. WA1787 Designing and Developing Higher Performance Web Services Classroom Setup Guide Web Age Solutions Inc. Copyright Web Age Solutions Inc. 1 Table of Contents Part 1 - Minimum Hardware Requirements...3

More information

WA1547 WebSphere Portal v6 Programming. Classroom Setup Guide. Web Age Solutions Inc. Copyright Web Age Solutions Inc.

WA1547 WebSphere Portal v6 Programming. Classroom Setup Guide. Web Age Solutions Inc. Copyright Web Age Solutions Inc. WA1547 WebSphere Portal v6 Programming Classroom Setup Guide Web Age Solutions Inc. 1 Table of Contents Classroom Requirements...3 Part 1 - Minimum Hardware Requirements...3 Part 2 - Minimum Software Requirements...3

More information

Easy Installation Guide

Easy Installation Guide Easy Installation Guide High Megapixel 360 Panomorph Mini Dome IP Network Camera MD-500Ap-360P Series MD-300Np-360P Series - 1 - Package Contents a. Camera b. Product CD c. Allen Key for The Lens d. Allen

More information

USB-MIDI Driver installation and settings...1 Windows XP users... 1

USB-MIDI Driver installation and settings...1 Windows XP users... 1 Installation Guide Table of Contents USB-MIDI Driver installation and settings...1 Windows XP users... 1 Installing the KORG USB-MIDI Driver... 1 Allowing driver installation without a digital signature...

More information

Installation Instructions for Medisoft 15 Network Professional

Installation Instructions for Medisoft 15 Network Professional Installation Instructions for Medisoft 15 Network Professional WARNING: If you are installing over a previous version of Medisoft, it is very important that you back up your data. Refer to the Medisoft

More information

OBDI Tune Kit Quick Start Guide

OBDI Tune Kit Quick Start Guide OBDI Tune Kit Quick Start Guide Revision A Page 1 Table of Contents Introduction... 3 Contents... 3 Early ECM Kits:... 3 Late ECM Kits:... 3 Minimum PC Requirements... 3 Program Installation... 4 Registering

More information

Detailed Installation Guide. Version 1.0

Detailed Installation Guide. Version 1.0 Detailed Installation Guide Version 1.0 Copyright 2009 Table of Contents Table of Contents General Guidelines...3 Kontakt Requirements...3 System Specifications...3 Installation of LASS DVDs...4 What to

More information

Figure 4-29 Removing the CPU compartment cover

Figure 4-29 Removing the CPU compartment cover 4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment

More information

RMX 2000/4000 MPMx Migration Procedure

RMX 2000/4000 MPMx Migration Procedure RMX 2000/4000 MPMx Migration Procedure Prior to initiating this procedure make sure you are entitled to version 7.0 in your Support Agreement. The MPMx requires software version 7.0 installed. First complete

More information

Software Package Installation Instructions

Software Package Installation Instructions Introduction Novar provides an automatic installation package that involves reading simple, easy-to-follow instructions on each screen and clicking on the appropriate options. This document provides detailed

More information

ECLIPSE LV Series Support Tools

ECLIPSE LV Series Support Tools M374E 07.1.NF.2 (3/3) ECLIPSE LV Series Support Tools (Setup software for ECLIPSE LV series microscopes) Software Manual Introduction Thank you for purchasing the Nikon products. This manual describes

More information

Integrated Sensor System TM (ISS) Gateway and Soil Manager TM v.1.1 Installation Procedure. Revised 2014/07/31

Integrated Sensor System TM (ISS) Gateway and Soil Manager TM v.1.1 Installation Procedure. Revised 2014/07/31 Integrated Sensor System TM (ISS) Gateway and Soil Manager TM v.1.1 Installation Procedure Revised 2014/07/31 Thank you for purchasing your new Rain Bird Integrated Sensor System TM (ISS). In this manual

More information

Software Setup Instructions for the Foster Control System used in the Explora Dome Observatories

Software Setup Instructions for the Foster Control System used in the Explora Dome Observatories Software Setup Instructions for the Foster Control System used in the Explora Dome Observatories Contents Pages 3 & 4 The new tic counter system & home position sensor Page 5 Control Boxes Pages 6-8 Down

More information

Infrared Interactive Whiteboard User Manual

Infrared Interactive Whiteboard User Manual Infrared Interactive Whiteboard User Manual Information in this manual is subject to change without notice. Content Important Information... 1 System Requirements... 2 Introduction... 3 How to install

More information

WA2168 Introduction to Java using Rational Application Developer 8.5. Classroom Setup Guide. Web Age Solutions Inc. Web Age Solutions Inc.

WA2168 Introduction to Java using Rational Application Developer 8.5. Classroom Setup Guide. Web Age Solutions Inc. Web Age Solutions Inc. WA2168 Introduction to Java using Rational Application Developer 8.5 Classroom Setup Guide Web Age Solutions Inc. Web Age Solutions Inc. 1 Table of Contents Part 1 - Minimum Hardware Requirements...3 Part

More information

Installation Note. Agilent PSA Series Spectrum Analyzers Secure Memory Erase, Option 117

Installation Note. Agilent PSA Series Spectrum Analyzers Secure Memory Erase, Option 117 Installation Note Agilent PSA Series Spectrum Analyzers Secure Memory Erase, Option 117 Part Number E4440-90323 Printed in USA July 2006 Notice. The information contained in this document is subject to

More information

Installing MacBook Pro 15" Unibody Mid 2010 Dual Hard Drive

Installing MacBook Pro 15 Unibody Mid 2010 Dual Hard Drive Installing MacBook Pro 15" Unibody Mid 2010 Dual Hard Drive Use this guide to install a second hard drive in place of the optical drive. Written By: Brittany McCrigler ifixit CC BY-NC-SA www.ifixit.com

More information

Replacing the Encoder Strip

Replacing the Encoder Strip 6-1-11. Replacing the Encoder Strip The following describes the procedure for replacing the Encoder Strip. Refer to the diagram below for identifying the parts and their positions. (The numbers shown in

More information

FileMaker. Mobile 2.1. User s Guide. For Windows, Mac, Palm OS, and Pocket PC. Companion for Palm OS and Pocket PC

FileMaker. Mobile 2.1. User s Guide. For Windows, Mac, Palm OS, and Pocket PC. Companion for Palm OS and Pocket PC For Windows, Mac, Palm OS, and Pocket PC FileMaker Mobile 2.1 Companion for Palm OS and Pocket PC User s Guide 2000-2002 FileMaker, Inc. All Rights Reserved. FileMaker, Inc. 5201 Patrick Henry Drive Santa

More information

Orion StarShoot P1 Polar Alignment Camera

Orion StarShoot P1 Polar Alignment Camera INSTRUCTION MANUAL Orion StarShoot P1 Polar Alignment Camera #6236 Providing Exceptional Consumer Optical Products Since 1975 OrionTelescopes.com Customer Support (800) 447-1001 E-mail: support@telescope.com

More information