SKYNET 2000 PRODUCT SPECIFICATIONS 11 DECEMBER, 2013 VERSION 1.1 ROOM CONTROL UNIT. Disclaimers and Copyright

Transcription

1 SKYNET 2000 ROOM CONTROL UNIT PRODUCT SPECIFICATIONS VERSION DECEMBER, 2013 Disclaimers and Copyright Nothing contained in this publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use in connection with any method, apparatus, or product covered by letters patent, or as insuring anyone against liability for infringement of letters patent. Efforts have been made to ensure the accuracy and reliability of the data contained in this publication; however, Citygrow Energy Systems Limited. makes no representation, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or from the use of any product or methodology described herein; for any violation of any federal, state, or municipal regulation with which this publication may conflict; or for the infringement of any patent from the use of this publication. Nothing contained in this publication should be viewed as an endorsement by Citygrow Energy Systems Limited. of any particular manufacturer s products. Copyright 2012 Citygrow Energy Systems Limited, All Rights Reserved 1

2 The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 2

3 SkyNET 2000 Room Control Unit 801hps Table of Contents 1.0. Features 2.0 Functional blocks Dimensions 4.0 Understanding of the product. 4.1 Understanding of the product. 5.0 System diagram basic configuration System diagram cascade configuration 6.0 Specification part Specification part Wiring before getting started Wiring case 1 : Loads are driven by AC line voltage. 7.2 Wiring case 2 : Not all loads are driven by AC line voltage. 8.0 How to build a model number Option items CG801SW4, 4 Channels Switch Card CG801SW8, 8 Channels Switch Card. 9.3 CG801DM2, 2 Channels Dimmer Card CG801FL2, 2 Channels 0-10V Dimmer Card 9.5 CG801LN, LAN Card. 9.6 CG801SKN-E, Circuit Extender 9.7.CG801FUS01, Mini Fuse 6.3A, AC250V, UL, VDE 9.8.CG801PS01, System Power Supply, 12V 5A, CE, UL.. Page

4 SkyNET 2000 Room Control Unit 801hps circuit extender RS485 5 sensor input control panel RS485 LAN 8 channel switch card Power Supply SkyNET 2000 Main Unit CG801SKN-M 5 card slots for Relay/ Dimmer card 1.0. Features SkyNet 2000 is a highly integrated Room Control System (RCU). Data communicates through RS485 bus and running on Citygrow s SmartBus protocols. Compact size 254x153x51mm (LxWxD) but integrated with maximum 28 lighting circuits. Circuit Extender CG801SKN-E can be added when more lighting circuits are needed for your project. Modular designs that is flexible for different types of projects. Different type of modular card is available : Dimmer Card, Relay Card, 0 10V Dimmer Card, LAN Card. Lighting on/off control, dimming, minimum dimming level setting, dimming curve preset. A/C control, thermostat and fan coil system control with high, mid, low speed, temperature preset. Electric curtain,,motorized window blind open/close/ stop control. User selectable curtain travel distance. Infra-Red device control. IR code learning function is supported. Do Not Disturb (DND ), Make UP Room (MUR), KeyCard detect for Hotel application. 5 sensor inputs are available for application, such as motion sensor, light sensor, magnet senor.etc. to trigger the corresponding lighting scene. Wall mount control panel CG800H-SKY and CG100H-SKY series is available. Wall mount control panel can be programmed with lighting scenes, A/C control, curtain control, DND, MUR or IR control. Control button graphics can be tailor-made per customer requirement. LAN card can be optional selected to support centralized server system control, management and reporting. SkyNet Planner is a PC software that is user friendly for programming the system. 4

5 154mm SkyNET 2000 Room Control Unit 2.0 Functional blocks 801hps SkyNET 2000 Main Unit, CG801SKN-M functional block diagram Power supply 5 sensor inputs, input 1 is default for keycard RS485 port for Circuit Extenders RS485 port for Control Panels Reset LED indicators Total 5 card slots. Cards can be: 1. 4 Channels Switch Card 2. 2 Channels Dimmer Card 3. 2 Channels 0 10V Dimmer Card UART 1 ( For MAC address) LAN ( Optional LAN Card required) UART 2 ( For Firmware update) System Neutral ( For Zero Crossing detection) 1 card slot for 8 Channels Switch Card ** Only channel 1 to 5 can be used for A/C fan coil control. ** If all cards are selected as 4 Channels Switch Card and 8 Channels Switch Card, the maximum number of control circuits will be : 5 slots x 4 Channels Switch Card = 20 Circuits 1 Slot x 8 Channels Switch Card = 8 Circuits Total number of control circuits = = 28 Circuits 3.0 Dimensions ****** 3 phase voltage is NOT allowed to be connected to system ********** 254mm 51mm 5

6 4.0. Understanding of the product SkyNET 2000 Room Control Unit 801hps Rear view 1.POWER SUPPLY DC 12V + 2.POWER SUPPLY GND 3.SESOR INPUT - COM 4.SESOR INPUT SESOR INPUT SESOR INPUT SESOR INPUT SESOR INPUT RS485 B TO CIRCUIT EXTENDER 10.RS485 A TO CIRCUIT EXTENDER 11.RS485 B TO PANEL 12.RS485 A TO PANEL 13.RESET 14.UART 1 (MAC ADDRESS ) 15.LAN 16.UART 2 (FIRMWARE) 17.NEUTRAL(SYSTEM) 18.CARD SLOT 6 24.MOUNTING HOLES 25.TOP COVER 26.ERROR LED 27.POWER LED 28.STATUS LED 29.REAR COVER Front view Top view 30. FRONT COVER 31. FRONT COVER SCREW LOCK 23.CARD SLOT 5 22.CARD SLOT 4 21.CARD SLOT 3 20.CARD SLOT 2 19.CARD SLOT 1 6

7 4.1. Understanding of the product SkyNET 2000 Room Control Unit 801hps Board to board connector for CG801SW8 36. CG801SW8 8 Channels Switch Card 38. CG801LN LAN Card 32. System address selection dip switch Top cabinet opened 35. CG801FL2 2 Channels 0 10V Dimmer Card 33. CG801SW4 4 Channels Switch Card 34. CG801DM2 2 Channels Dimmer Card ** Different types of card is flexible to be inserted into card slot 1 5 according to your application requirement. ** 7

8 5.0 System diagram basic configuration SkyNET 2000 Room Control Unit 801hps Basic configuration only one SkyNET main unit is being used CG801SKN-M SkyNET 2000 Main Unit To Loads -lamps -curtains -fan coils are NOT allowed To Loads -fan coils -lamps -curtains DC 12V Daisy chain Wall mount control panels RS485 bus DC 12V Power supply AC 220V AC 220V Neutral( for Zero crossing detection) To LAN (for central control) - Optional 8

9 5.1 System diagram-cascade configuration SkyNET 2000 Room Control Unit 801hps Cascade configuration multiple Circuit Extenders are connected to one SkyNET main unit, in order to increase the number of load circuits To Loads -lamps -curtains -fan coils are NOT allowed CG801SKN-M SkyNET 2000 Main Unit To Loads -fan coils -lamps -curtains DC 12V Power supply Daisy chain AC 220V Wall mount control panels RS485 bus DC 12V AC 220V Neutral( for Zero crossing detection) To LAN (for central control) - Optional Daisy chain To maximum 7 Circuit Extender CG801SKN-E SkyNET 2000 Circuit Extender CG801SKN-E SkyNET 2000 Circuit Extender 9

10 SkyNET 2000 Room Control Unit 801hps Specifications Function Group Power Supply 1. Power Supply DC12V + 2. Power Supply GND Item Specification Details 1. DC 12V, 5A 2. Support 1 main unit plus 32 panels. 1. External SMPS power supply ( Included). 2. For power supply to SkyNet main unit 3. For power supply to Control Panel, maximum support 32 panels. Sensor Input 3. Sensor input COM 4. Sensor input 1** 5. Sensor input 2 6. Sensor input 3 7. Sensor input 4 8. Sensor input 5 Circuit Extender port Panel port 9. RS485 B to Circuit Extender 10. RS485 A to Circuit Extender RS485 B to Panel RS485 A to Panel 1. NO (normal open) 2. Internal 1K ohm pull up to DC14V 1. RS Maximum support 7 circuit extenders 1. RS Maximum support 32 control panels. 1. **Sensor input 1 is default for KEYCARD to trigger lighting scene function. 2. Sensor input 2 to 5 is for normal sensor input. 3. When activated, use relay to short circuit to COM. 4. Or use open collector to short circuit to COM. 1. If Circuit Extender CG801SKN-E is added to the system. Connect RS485 A and RS485 B to the corresponding pins of Circuit Extender. Maximum 7 Circuit Extender can be connected to SkyNET2000 main unit CG801SKN- M. 2. It is recommended to use Belden 8723 cable. 3. RS485 terminator 120ohm resistor is needed to be added to end the cable. See wiring diagram SkyNET For connection to wall mount control panels CG100H-SKY and CG800H- SKY series. 2. Panels should be connected in daisy chain configuration. Maximum 32 control panels can be connected. 3. Connect RS485 A and RS485 B to the corresponding connector. 4. It is recommended to use Belden 8723 cable. 5. RS485 terminator 120ohm resistor is needed to be added to end the cable. See wiring diagram SkyNET Reset 13.Reset 1. System reset 1. For system reset MAC address program port 14. UART 1 1. UART 1. For MAC address programming. 2. By default, the LAN card is already programmed in factory. LAN port 15.LAN 1. LAN 1. For communication with Server software ( Tailor made software). 2. For communication with third party system. Firmware program port Neutral, for system 16. UART 1. UART 1. For factory firmware programming. 17A. Neutral ( System) 1. Neutral connection to AC line voltage, for SkyNET 2000 system Neutral. 1. Minimum 1.5mm copper diameter, black color is recommended. 10

11 SkyNET 2000 Room Control Unit 6.1. Specifications 801hps Function Group Option card slots Item Details 18. Optional card slot 6 Card slot for : 1. CG801SW8, 8 Channels Switch Card ONLY. 19.Optional card slot 1 Card slots for : 1. CG801SW4, 4 Channels Switch Card 2. CG801FL2, 2 Channels 0 10V Dimmer Card 20. Optional card slot 2 3. CG801DM2, 2 Channels Dimmer Card 21. Optional card slot 3 4. The above 3 different types of card can be installed in Slot 1, 2, 3, 4, or The number of cards selected depends on your project application. 22. Optional card slot 4 System mounting holes 23. Optional card slot Mount holes 1. 4 mounting holes on left mounting holes on right. Top cover 25. Top cover 1. Open the top cover for installation and maintenance purpose. 2. Before opening the Top Cabinet, make sure power is down. 3. Before power is supplied to SkyNET 2000, make sure each circuit connection is correct. 4. Prevent blocking the ventilation slots on top cabinet. LED indicators 26. Error LED 27. Power LED 28. Status LED Error LED: When No Ethernet connection, Error LED will be ON. Power LED: When SkyNET planner settings is not uploaded to SkyNET main unit, Power LED will be blinking. In normal situation, when power is on, Power LED will be ON. Status LED: (Optional for future development) Rear cover 29. Rear cover 1. Open the rear cover for installation and maintenance purpose. 2. Before opening the rear cabinet, make sure power is down. 3. Before power is supplied to SkyNET 2000, make sure each circuit connection is correct. 4. Prevent blocking the ventilation slots on rear cabinet. Front cover System address 30. Front cover 31. Front cover screw lock 32. System address selection Dip switch Dimensions Length x Width x Depth 254x154x51 mm Temperature Recommended operation temperature Bus Bus standard RS Open the front cover for installation and maintenance purpose. 2. Before opening the front cabinet, make sure power is down. 3. Before power is supplied to SkyNET 2000, make sure each circuit connection is correct. 4. Lock the front cover screw lock to securely fix the front cover. 1. Dip switch 1 to 8 for setting the system address. 2. Normally, the main unit CG801SKN-M should be set to In case Circuit Extender CG801SKN-E is added, the Circuit Extender can be set to , etc. 4. Please refer the SkyNET Planner user manual for details. 0 to 40 degree C Protocol Bus maximum length Cable Citygrow SmartBus protocol Below 1000M Belden 8723 or equivalent 11

12 7.0 Wiring before getting started SkyNET 2000 Room Control Unit 801sw Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 12

13 SkyNET 2000 Room Control Unit 801sw Wiring case 1: Loads are driven by AC line voltage CG801SW4, 4 Channels Switch Card inside SkyNET 2000 Main unit Card Slots for other cards Neutral (System) Load 4 CG801SW4, 4 Channels Switch Card Load 3 Power supply Load 1 Neutral Live Distribution board Neutral point for CG801SW4. Make sure this screw is securely fastened to provide good contact for Neutral Connection. This Neutral point is internally connected to Neutral ( System). ****** 3 phase voltage is NOT allowed to be connected to system ********** 13

14 7.2 Wiring case 2: Not all loads are driven by AC line voltage SkyNET 2000 Room Control Unit 801sw CG801SW4, 4 Channels Switch Card inside SkyNET 2000 Main unit Card Slots for other cards Neutral (System) Load 2 will have Zero Crossing detection, since Load 1 input is connected to Live. Load 3 and Load 4 will not have Zero crossing detection. Load 4 CG801SW4, 4 Channels Switch Card Input 4 Input 3 Load 3 Load 2 Power supply Load 1 Neutral Live Distribution board Neutral point for CG801SW4. Make sure this screw is securely fastened to provide good contact for Neutral Connection. This Neutral point is internally connected to Neutral ( System). ****** 3 phase voltage is NOT allowed to be connected to system ********** 14

15 8.0 How to Build a Model Number SkyNET 2000 Room Control Unit 801sw CG801xxx-x Product series number Functional option SKN-M SKN-E SW4 ESW2 SW8 DM2 FL2 LN FUS01 PS01 = SkyNET Main unit = SkyNET Circuit Extender = 4 Channels Switch Card = 2 Channel E-Circuit Switch Card = 8 Channels Switch Card = 2 Channels Dimmer Card = 2 Channels 0 10V Dimmer Card = LAN Card = Mini Fuse = System Power Supply 15

16 SkyNET 2000 Room Control Unit 801sw Optional items 9.1.CG801SW4, 4 Channels Switch Card 9.2.CG801SW8, 8 Channels Switch Card 9.3.CG801DM2, 2 Channels Dimmer Card 9.4.CG801FL2, 2 Channels 0-10V Dimmer Card 9.5.CG801LN, LAN Card 9.6.CG801SKN-E, SkyNET 2000 Circuit Extender 9.7.CG801FUS01, Mini Fuse 6.3A, AC250V, UL, VDE 9.8.CG801PS01, System Power Supply, 12V 5A, CE, UL 16

17 CG801SW4 4 Channels Switch Card sw Description CG801SW4 4 Channels Switch Card 4 Channels Switch Card for SkyNET 2000 system. Microprocessor controlled. Built-in relay switch with Zero Crossing detection technology. Independent fuse protection for each channel. Fuses are easy to access and replaceable. Specifications Item Specification Power requirement loads 220VAC to 240VAC, 50Hz This device can only function when it is installed inside Citygrow s SkyNET 2000 system. Resistive load : 1000W/gang (For Incandescent, Halogen, Electronic low voltage ELV Transformer) Inductive load : 1000VA/gang ( For magnetic low voltage MLV transformer, Iron core/inductive transformer) Fluorescent: 700W/gang Compact fluorescent CFL : 400W / gang LED GU10 : 200W/gang LED MR16, MR11( with electronic low voltage LED driver): 400W /gang LED strip( with electronic low voltage LED driver) : 400W /gang Exhaust fan: 300VA/gang Channel 1 If input 1 is not connected to Live, Zero Crossing protection will not function for the relays output 2, 3, or 4. Channel 2, 3 or 4 Operational temperature If these channels are intended to be driven by AC line voltage, please connect the inputs for these channels to the input of Channel 1 the Live from the AC line voltage. 0 deg C to 40 deg C Humidity 5% to 95% non-condensing Storage -20 deg C to 70 deg C Dimension L X W x D (mm) 95x41x21 17

18 95mm CG801SW4 4 Channels Switch Card Dimensions 801sw mm 21mm Understanding of the product Neutral Screw Hole (For connection to system neutral ) Board to board connector Fuse Channel 1 Channel 2 Channel 3 Channel 4 See Remarks ** 1.Load 1 2.Input 1 3.Load 2 4.Input 2 5.Load 3 6.Input 3 7.Load 4 8.Input 4 See Remarks ** 1. Input 1 or 2 or 3 or 4 can be connected to AC line voltage Live, or other specific input for the load, depending on your application. 2. If input 1 or 2 or 3 or 4 requires AC line voltage Zero crossing protection, the AC Live cable should be connected to Input 1. Then, use wire to short circuit from input 1 to input 2, 3, 4. ****** 3 phase voltage is NOT allowed to be connected to system ********** 18

19 CG801SW4 4 Channels Switch Card 801sw4ps Wiring General wiring, all loads are driven by AC line voltage CG801SW4, 4 Channels Switch Card (installed inside SkyNET 2000 system) Load 4 Load 3 Load 2 Make sure this screw is securely fastened to provide good contact for Neutral Internal connection to CG801SKN-M Neutral ( System) Live Load 1 ****** 3 phase voltage is NOT allowed to be connected to system ********** Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 19

20 CG801SW4 4 Channels Switch Card 801sw4ps Wiring NOT all loads are driven by AC line voltage CG801SW4, 4 Channels Switch Card (installed inside SkyNET 2000 system) Load 4 Input 3 Input 4 Load 3 Load 2 Make sure this screw is securely fastened to provide good contact for Neutral Internal connection to CG801SKN-M Neutral ( System) Live Load 1 ** Remarks: In this case, Channel 1 and Channel 2 are driven by AC line voltage with same phase and is Zero Crossing protected. Channel 3 and Channel 4 are independent input channel, it can be dry contact input or DC voltage input. ****** 3 phase voltage is NOT allowed to be connected to this card ********** Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 20

21 CG801SW8 8 Channels Switch Card 9.2 Description 801sw CG801SW8, 8 Channels Switch Card Specifications Item 8 Channels Switch Card for SkyNET 2000 system. Microprocessor controlled. Built-in relay switch with Zero Crossing detection technology. Channel 1 to Channel 5 is for A/C fan coil control or for general purpose switch function. Channel 6 to Channel 8 is for general purpose switch function. Independent fuse protection for each channel. Fuses are easy to access and replaceable. Specification Power requirement loads 220VAC to 240VAC, 50Hz This device can only function when it is installed inside Citygrow s SkyNET 2000 system. RESISTIVE LOAD : 1000W/gang (For Incandescent, Halogen, Electronic low voltage ELV Transformer) INDUCTIVE LOAD : 1000VA/gang ( For magnetic low voltage MLV transformer, Iron core/inductive transformer) FLUORESCENT : 700W/gang COMPACT FLUORESCENT CFL : 400W / gang LED GU10 : 200W/gang LED MR16, MR11( with electronic low voltage LED driver): 400W/gang LED strip( with electronic low voltage LED driver) : 400W/gang EXHAUST FAN: 300VA/gang Channel 1 to Channel 5 If Air-conditioning fan coil control is needed to be connected to SkyNET 2000, Channel 1 to Channel 5 of CG801SW8 is the default connection ports. These 5 channels are for High, Mid, Low, Cool, Heat function If Channel 1 to Channel 5 are not for fan coil control function, they can be programmed ( by SkyNET planner software) as general switch to control lamps, curtain...etc., as specified in supported load types in this table. Channel 1 input should be connected to the Live of the AC line voltage, if Zero crossing function is needed for channel 1, or 2 or 3 or 4.or 8. If all loads in all channels are intended to be driven by AC line voltage, please connect the input of all channels to the input of channel Live of AC line voltage. If load / loads is not intended to be driven by AC line voltage, the input pin of that channel can be connected to the input source depending on your application. Channel 6 to Channel 8 Operational temperature Humidity If these channels are intended to be driven by AC line voltage, please connect the inputs for these channels to the input of Channel 1 the Live of AC line voltage. 0 deg C to 40 deg C 5% to 95% non-condensing Storage Dimension L X W x D (mm) -20 deg C to 70 deg C 95x48.5x17 21

22 97mm CG801SW8 8 Channels Switch Card Dimensions 801sw mm 17mm Understanding of the product Board to board connector Fuse Connect to SkyNET main unit Neutral Input 1 Load 1 Input 2 Load 2 Input 3 Load 3 Input 4 Load 4 Input 5 Load 5 Input 6 Load 6 Input 7 Load 7 Input 8 Load 8 Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 ** Remarks ** 1. Input 1 to 8 can be connected to AC line voltage Live, or other specific input for the load, depending on your application. 2. If input 1 to 8 requires AC line voltage Zero Crossing detection to protect the relay/ relays, the AC Live wire should be connected to Input 1. Then, use wires to short circuit from input 1 to input 2, 3, 4, 5, 6, 7, If fan coil control is needed, please only use channel 1 to channel 5 for fan coil control. 22

23 CG801SW8 8 Channels Switch Card 801sw Wiring General wiring, all loads are driven by AC line voltage To Neutral (System) Live Load 1 Load 2 Load 3 Load 4 Load 5 Load 6 Load 7 CG801SW8, 8 Channels Switch Card (installed inside SkyNET 2000 system) Load 8 ****** 3 phase voltage is NOT allowed to be connected to system ********** 23

24 CG801SW8 8 Channels Switch Card 801sw Wiring Fan coil connected Fan coil To Neutral (System) Live High Mid Low Cool Heat Load 6 Load 7 CG801SW8, 8 Channels Switch Card (installed inside SkyNET 2000 system) Load 8 ****** 3 phase voltage is NOT allowed to be connected to system ********** 24

25 CG801SW8 8 Channels Switch Card 801sw Wiring NOT all loads are driven by AC line voltage To Neutral (System) Live Load 1 Load 2 Load 3 Input 3 Input 4 Load 4 Input 5 Load 5 Input 6 Input 7 Load 6 Input 8 Load 7 CG801SW8, 8 Channels Switch Card (installed inside SkyNET 2000 system) Load 8 ** Remarks: In this case, Channel 1 and Channel 2 are driven by AC line voltage and is Zero Crossing protected. Channel 3 to Channel 8 are independent input channel. ****** 3 phase voltage is NOT allowed to be connected to system ********** Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 25

26 CG801DM2 2 Channels Dimmer Card dm2ps Description Specifications CG402DM2, 2 gang dimmer card Item 2 Channels Dimmer Card for SkyNET 2000 system. Microprocessor controlled. Leading edge (forward phase) type dimmer. Independent fuse protection for each gang. Fuses are easy to access and replaceable. Compatible with incandescent, line-voltage halogen, and magnetic ( iron core ) transformers. Specification Power requirement 220VAC to 240VAC, 50Hz This device can only function when it is installed inside Citygrow s SkyNET 2000 system. loads RESISTIVE LOAD : 400W/gang (For Incandescent, Halogen, Electronic low voltage ELV Transformer) INDUCTIVE LOAD : 400VA/gang ( For magnetic low voltage MLV transformer, Iron core/inductive transformer) DIMMABLE COMPACT FLUORESCENT CFL :250W, Max. 20 pcs CFL/gang** LED GU10 : 40W/gang LED MR16, MR11( with electronic low voltage LED driver): 80W, Max. 15 pcs ELV LED driver/gang. Dimming remarks W x 2 gang or 800W x 1 gang supported 2. Leading Edge Dimmable Fluorescents, Compact Fluorescents and LEDs, see remarks. Remarks: 1. The maximum load requirements for fluorescent, CFL and LED loads can vary greatly depending upon the specific fixture and /or bulb being used. 2. When dimming transformer is connected to CG801DM2, make sure dimmable and leading edge type is used. Furthermore, the dimming performance varies greatly from manufacturer to manufacturer of the bulb and the dimming transformer. It is recommended to test the matching performance before mass deployment. Minimum load Minimum dimming level preset 5W/ channel By using SkyNET planner software, minimum dimming level can be programmed to each of the dimming channel to fix for different types of driver. Operational temperature 0 deg C to 40 deg C Humidity 5% to 95% non-condensing Storage -20 deg C to 70 deg C Dimension L X W x D (mm) 95x41x23 26

27 95mm CG801DM2 2 Channels Dimmer Card Dimensions 801dm2ps mm 23mm Understanding of the product Board to board connector Heat sink Fuse ( Load 1 ) Fuse ( Load 2 ) Live input Load 1 Load 2 ****** 3 phase voltage is NOT allowed to be connected to system ********** 27

28 CG801DM2 2 Channels Dimmer Card 801dm2ps Wiring General wiring, all loads are driven by AC line voltage CG801DM2, 2 Channels Dimmer Card (installed inside SkyNET 2000 system) Load 2 To Neutral (System) Live To Neutral (System) Make sure this screw is securely fastened to provide good contact for Neutral Internal wiring from SkyNET 2000 main system ( Neutral ) Load 1 ****** 3 phase voltage is NOT allowed to be connected to system ********** Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 28

29 CG801FL2 2 Channels 0-10V Dimmer Card fl2ps Description CG801FL2, 2 Channels 0-10V Dimmer Card 2 Channels 0-10V Dimmer Card for SkyNET 2000 system. Microprocessor controlled. Built-in relay switch with Zero Crossing detection technology. DC 0-10V linear dimming voltage for LED or dimmable fluorescent lamp. Independent fuse protection for each channel. Fuses are easy to access and replaceable. Specifications Item Specification Power requirement Supported load types 220VAC to 240VAC, 50Hz This device can only function when it is installed inside Citygrow s SkyNET 2000 system. Fluorescent with 0-10V dimming driver: 700W /gang, Max 24 pcs 0-10V dimming interface. LED MR16, MR13 with 0 10V dimming driver : 400W/gang, Max. 24 pcs dimming driver connected to it. LED LED strip with 0-10V dimming driver: 400W/gang, Max. 10pcs dimming driver connected to it. Maximum load ( 0 10V output) 25mA / channel Input 1 & 2 AC line voltage input Live Com Common for 0 10V output. Load 1, Load 2 1. Input 1 & 2 is the Live input for Channel 1 and Channel When 0 10V output comes to 0V, the Load 1 or Load 2 output will be OFF. 3. When 0 10V output is > 0V, the Load 1 or Load 2 output will be ON Operational temperature 0 deg C to 40 deg C Humidity 5% to 95% non-condensing Storage -20 deg C to 70 deg C Dimension L X W x D (mm) 95x41x21 29

30 95mm CG801FL2 2 Channels 0-10V Dimmer Card Dimensions 801fl2ps mm 21mm Understanding of the product Neutral Screw Hole (For connection to system neutral ) Board to board connector Load 1 Fuse Input 1 & 2 Load V (Channel 1) Com 0 10V (Channel 2) **See Remarks ** 1. Input 1 & 2 is the Live input for Channel 1 and Channel When 0 10V output comes to 0V, the Load 1 or Load 2 output will be OFF. 3. When 0 10V output is > 0V, the Load 1 or Load 2 output will be ON ****** 3 phase voltage is NOT allowed to be connected to system ********** 30

31 CG801FL2 2 Channels 0-10V Dimmer Card 801fl2ps Wiring general wiring CG801FL2, 2 Channels 0-10V Dimmer Card (installed inside SkyNET 2000 system) Load 1 To Neutral ( System) 0-10V input + - Make sure this screw is securely fastened to provide good contact for Neutral Internal connection to CG801SKN-M Neutral ( System) Live 0-10V input + - Load 2 To Neutral ( System) ****** 3 phase voltage is NOT allowed to be connected to system ********** Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 31

32 CG801LN LAN Card lnps Description Ethernet connection for SkyNET 2000 For centralized server system control and monitoring for SkyNET IEEE Base-T Ethernet IEEE802.3u 100Base-TX Fast Ethernet ANSI/IEEE N Way Auto-Negotiation IEEE802.3x Full Duplex Flow Control Support CG801LN, LAN Card Specifications Item Specification Power requirement Power supplied by SkyNET 2000 main Standard IEEE Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet ANSI/IEEE N Way Auto-Negotiation IEEE 802.3x Full Duplex Flow Control Support Network Data Transfer Rate Protocol Ethernet: 10Mbps (Half-duplex) Ethernet: 20Mbps (Full-duplex) Fast Ethernet: 100Mbps (Half-duplex) Fast Ethernet: 200Mbps (Full-duplex) CSMA/CD Network Media Ethernet: UTP Cat3, 4, 5 EIA/TIA ohm screened twisted-pair (STP) Fast Ethernet: UTP Cat5, EIA/TIA ohm screened twisted-pair (STP) Certificate FCC Operational temperature 0 deg C to 40 deg C Humidity 5% to 95% non-condensing Storage -20 deg C to 70 deg C Dimension L X W x D (mm) 95x41x21 32

33 9.6 Description CG801SKN-E Circuit Extender 801skneps Specifications Function Group CG801SKN-E, Circuit Extender Power Supply 1. Power Supply DC12V + 2. Power Supply GND Circuit Extender CG801SKN-E is optional for increasing the number of lighting circuit in SkyNET 2000 system. Data communicates with SkyNET Main Unit through RS485 bus. Compact size 254x153x51mm (LxWxD) but integrated with maximum 28 lighting circuits. Modular designs that is flexible for different types of projects. Different type of modular card is available : Dimmer Card, Relay Card, 0 10V Dimmer Card. Lighting on/off control, dimming, minimum dimming level setting, dimming curve preset. A/C control, thermostat and fan coil system control with high, mid, low speed, temperature preset. Curtain, window blind open/close/ stop control. User selectable curtain travel distance. 5 sensor inputs are available for application, such as motion sensor, light sensor, magnet senor.etc. to trigger the corresponding lighting scene. SkyNet Planner is a PC software that is user friendly for programming the system. Item Specification Details 1. DC 12V, 5A 1. External SMPS power supply ( Included) Sensor Input 3. Sensor input COM 4. Sensor input 1** 5. Sensor input 2 6. Sensor input 3 7. Sensor input 4 8. Sensor input 5 Circuit Extender port 9. RS485 B to CG801SKN-M Main Unit. 10. RS485 A to CG801SKN-M Main Unit. 1. NO (normal open) 2. Internal 1K ohm pull up to DC14V 1. **Sensor input 1 is default for KEYCARD input to trigger lighting scene function. 2. Sensor input 2 to 5 is for normal sensor input. 2a. When activated, use relay to short circuit to COM. 2b. Or use open collector driver to short circuit to COM. 1. RS Connect RS485 A and RS485 B to the corresponding pins of Main Unit. 2. Maximum 7 Circuit Extender can be connected to SkyNET2000 main unit CG801SKN-M. 3. It is recommended to use Belden 8723 cable. 4. RS485 terminator 120ohm resistor is needed to be added to end the cable. See wiring diagram SkyNET Reset 13.Reset 1. System reset 1. For system reset MAC address program port 14. UART 1 1. UART 1. For MAC address programming. 2. By default, the LAN card is already programmed in factory. LAN port 15.LAN 1. LAN 1. For communication with Server software ( Tailor made software). 2. For communication with third party system. Firmware program port Neutral, for system 16. UART 1. UART 1. For factory firmware programming. 17A. Neutral ( System) 1. Neutral connection to AC line voltage, for SkyNET 2000 system Neutral. 1. Minimum 1.5mm copper diameter, black color is recommended. 33

34 CG801SKN-E Circuit Extender Specifications Function Group Optional card slots System mounting holes Item Specification 18. Optional card slot 6 Card slot for : 1. CG801SW8, 8 Channels Switch Card ONLY. 19.Optional card slot 1 Card slots for : 1. CG801SW4, 4 Channels Switch Card 2. CG801FL2, 2 Channels 0 10V Dimmer Card 20. Optional card slot 2 3. CG801DM2, 2 Channels Dimmer Card 21. Optional card slot 3 4. The above 3 different types of card can be installed in Slot 1, 2, 3, 4, or The number of cards selected depends on your project application. 22. Optional card slot Optional card slot Mount holes 1. 4 mounting holes on left mounting holes on right. Top cover 25. Top cover 1. Open the top cover for installation and maintenance purpose. 2. Before opening the Top Cabinet, make sure power is down. 3. Before power is supplied to SkyNET 2000, make sure each circuit connection is correct. 4. Prevent blocking the ventilation slots on top cabinet. LED indicators 26. Error LED 27. Power LED 28. Status LED Error LED: When No Ethernet connection, Error LED will be ON. Power LED: When SkyNET planner settings is not uploaded to SkyNET main unit, Power LED will be blinking. In normal situation, when power is on, Power LED will be ON. Status LED: (Optional for future development) Rear cover 29. Rear cover 1. Open the rear cover for installation and maintenance purpose. 2. Before opening the rear cabinet, make sure power is down. 3. Before power is supplied to SkyNET 2000, make sure each circuit connection is correct. 4. Prevent blocking the ventilation slots on rear cabinet. Front cover System address 30. Front cover 31. Front cover screw lock 32. System address selection Dip switch Dimensions Length x Width x Depth 254x154x51 mm Temperature Recommended operation temperature Bus Bus standard RS Open the front cover for installation and maintenance purpose. 2. Before opening the front cabinet, make sure power is down. 3. Before power is supplied to SkyNET 2000, make sure each circuit connection is correct. 4. Lock the front cover screw lock to securely fix the front cover. 1. Dip switch 1 to 8 for setting the system address. 2. Normally, the main unit CG801SKN-M should be set to In case Circuit Extender CG801SKN-E is added, the Circuit Extender can be set to , etc. 4. Please refer the SkyNET Planner user manual for details. 0 to 40 degree C 801skneps Protocol Bus maximum length Cable CG SmartBus protocol Below 1000M Belden 8723 or equivalent 34

35 154mm CG801SKN-E Circuit Extender Functional blocks 801skneps SkyNET 2000 Circuit Extender, CG801SKN-E functional block diagram Power supply 5 sensor inputs, input 1 is default for keycard RS485 port to Main Unit Reset LED indicators Total 5 card slots. Cards can be: 1. 4 Channels Switch Card 2. 2 Channels Dimmer card 3. 2 Channels 0 10V Dimmer Card UART 1 ( For MAC address) UART 2 ( For Firmware update) System Neutral ( For Zero Crossing detection) 1 card slot for 8 Channels Switch Card ** Only channel 1 to 5 can be used for A/C fan coil control. ****** 3 phase voltage is NOT allowed to be connected to system ********** ** If all cards are selected as 4 Channels Switch Card and 8 Channels Switch Card, the maximum number of control circuits will be : 5 slots x 4 Channels Switch Card = 20 Circuits 1 Slot x 8 Channels Switch Card = 8 Circuits Total number of control circuits = = 28 Circuits Dimensions 254mm 51mm 35

36 CG801SKN-E Circuit Extender Understanding of the product 801skneps Rear view 1.POWER SUPPLY DC 12V + 2.POWER SUPPLY GND 3.SESOR INPUT - COM 4.SESOR INPUT SESOR INPUT SESOR INPUT SESOR INPUT SESOR INPUT RS485 B TO MAIN UNIT 10.RS485 A TO MAIN UNIT 11.NC 12.NC 13.RESET 14.UART 1 (MAC ADDRESS ) 15.NC 16.UART 2 (FIRMWARE) 17.NEUTRAL(SYSTEM) 18.CARD SLOT 6 24.MOUNTING HOLES 25.TOP COVER 26.ERROR LED 27.POWER LED 28.STATUS LED 29.REAR COVER Front view Top view 30. FRONT COVER 31. FRONT COVER SCREW LOCK 23.CARD SLOT 5 22.CARD SLOT 4 21.CARD SLOT 3 20.CARD SLOT 2 19.CARD SLOT 1 36

37 CG801SKN-E Circuit Extender Understanding of the product 801skneps Board to board connector for CG801SW8 36. CG801SW8 8 Channels Switch Card 32. System address selection dip switch Top cabinet opened 35. CG801FL2 2 Channels 0 10V Dimmer Card 33. CG801SW4 4 Channels Switch Card 34. CG801DM2 2 Channels Dimmer Card ** Different types of card is flexible to be inserted in to card slot 1 5 according to your application requirement. ** 37

38 CG801SKN-E Circuit Extender 801skneps Wiring Before getting started WARNING! It must be installed by a qualified electrician in accordance with all applicable regulations and building codes. Improper wiring can result in personal injury or damage to control units or other equipment. Always turn off circuit breaker or remove main fuse from power line before doing any work. To avoid overheating and possible damage to equipment. WARNING! Do not operate when any lamps removed or burned out; replace any burned out lamps immediately; use only transformers that incorporate thermal protection or fused primary windings.! This product is designed for residential and commercial use, for indoor use only. WARNING! Install in accordance with all national and local electrical codes. IMPORTANT! Citygrow is not liable for any damage incurred with the misuse of this product. IMPORTANT! Pre-setup can only be done by a professional worker or manufacturer agent. 38

39 CG801SKN-E Circuit Extender 801skneps Wiring cases Case 1: Loads are driven by AC line voltage CG801SW4, 4 Channels Switch Card inside CG801SKN-E Circuit Extender Card Slots for other cards Neutral (System) Load 4 CG801SW4, 4 Channels Switch Card Load 3 Power supply Load 1 Neutral Live Distribution board Neutral point for CG801SW4. Make sure this screw is securely fastened to provide good contact for Neutral Connection. This Neutral point is internally connected to Neutral ( System). ****** 3 phase voltage is NOT allowed to be connected to system ********** 39

40 CG801SKN-E Circuit Extender 801skneps Wiring cases Case 2: Not all loads are driven by AC line voltage CG801SW4, 4 Channels Switch Card inside CG801SKN-E Circuit Extender Card Slots for other cards Neutral (System) Load 2 will have Zero Crossing detection, since Load 1 input is connected to Live. Load 3 and Load 4 will not have Zero crossing detection. Load 4 CG801SW4, 4 Channels Switch Card Input 4 Input 3 Load 3 Load 2 Power supply Load 1 Neutral Live Distribution board Neutral point for CG801SW4. Make sure this screw is securely fastened to provide good contact for Neutral Connection. This Neutral point is internally connected to Neutral ( System). 40

41 CG801FUS01 Mini Fuse 250V 6.3A fusps Description CG801LN, LAN Card Mini Fuse for SkyNET optional cards. For CG801SW4, 4 Channels Switch Card. For CG801SW8, 8 Channels Switch Card. For CG801DM2, 2 Channels Dimmer Card. For CG801FL2, 2 Channels 0-10 V Dimmer Card. AC250V, 6.3A. CQC, UR, SEMKO, PSE, VDE, BSI, ROHS. Specifications Item Specification Rating AC250V, 6.3A Approval CQC,UR, SEMKO, PSE, VDE, BSI, 5et RoHS IEC60127, GB9364 Flammability classification of material Pre-arcing time Current Characteristics UL 94V-0 When the current in the following is passing the fuse, its opening time must be in accordance with the requirements in the following, that is, the pre-arcing time. Moreover, there shall be not damaged or shattered of the square thermoplastic cap. Rated Current 2.1ln 2.75ln 4ln 10ln Max. Min. Max. Min. Max. Min. Max. 100mA 6.3A 2min 400 ms 10s 150 ms 3s 20ms 150ms Operational temperature Humidity -55 deg C to 125 deg C 5% to 95% non-condensing Storage -55 deg C to 85deg C 41

42 9.8 Description CG801PS01 System Power Supply 801fusps CG801PS01, System Power Supply Power Supply for CG801SKN-M, SkyNET 2000 Main unit. Power Supply for CG801SKN-E, SkyNET 2000 Circuit Extender. Constant voltage output. Universal AC input / Full range. Withstand 300VAC surge input for 5 seconds. Protections: Short Circuit/ Overload / Over voltage. Cooling by free air convection. Fully encapsulated with IP67 level. Fully isolated plastic case. Class II power unit, no FG. Class 2 power unit. Pass LPS. 100% full load burn-in test. Specifications Item Specification Input voltage Frequency AC current Inrush current Leakage current Output voltage Output current Rated power Voltage tolerance Load regulation VAC 47 63Hz 1.2A/115VAC, 1A/230VAC Cold start 60A(Twidth=525uS measured at 50% lpeak) at 230VAC 0.25mA/240VAC 12V DC 0 5A 60W +/- 5% +/- 2% Overload protection Over voltage protection Safety standards Operational temperature Humidity % rated output power V ( Shut down o/p voltage, re-power on to recover) UL879, UL1310, CSA C22 NO.207-M89, CAN/CSA C22.2 NO.223-M91, IP67 approved; design refer to TUV EN EMC: Compliance to EN55022(CISPR22)Class B, EN Class A, EN EN ,3,4,5,6,8,11, EN55024, light industry level, criteria A -30 deg C to 70 deg C 20% to 90% non-condensing Storage Dimensions -40 deg C to 80deg C 162.5x42.5x32 mm ( LxWxD) 42

43 Disclaimers and Copyright Nothing contained in this publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use in connection with any method, apparatus, or product covered by letters patent, or as insuring anyone against liability for infringement of letters patent. Efforts have been made to ensure the accuracy and reliability of the data contained in this publication; however, Citygrow Energy Systems Limited. makes no representation, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or from the use of any product or methodology described herein; for any violation of any federal, state, or municipal regulation with which this publication may conflict; or for the infringement of any patent from the use of this publication. Nothing contained in this publication should be viewed as an endorsement by Citygrow Energy Systems Limited. of any particular manufacturer s products. Copyright 2012 Citygrow Energy Systems Limited, All Rights Reserved 43