SECTION 7 SMA/SMA-COM/BMA R125/R124/R128 SIMPLIFICATION IS OUR INNOVATON. Visit for more information

Transcription

1 SECTION 7 /COM/BMA R125/R124/R128 SIMPLIFICATION IS OUR INNOVATON Visit for more information

2 Contents BMA Introduction Characteristics Plugs Jacks to 78 Receptacles...78 to 711 Panel drilling to 712 Introduction to 714 Interface Characteristics to 717 Straight plugs to 718 Right angle plugs to 721 Straight jacks Bulkhead jacks to 725 Receptacles to 730 Receptacles for microstrip to 732 Hermetic receptacles with separate glass bead Hermetic receptacles with integrated glass bead Hermetic receptacles without glass bead Adapters to 736 Accessories Glass beads Accessories for hermetic microstrip receptacles Panel drilling to 740 Tooling for hermetic receptacles Field replaceable hermetic microstrip receptacle information to 742 COM Introduction to 744 Interface Characteristics Plugs to 748 Jacks to 749 Receptacles and switches to 752 Panel drilling Assembly instructions to 754 SECTION 7 TABLE OF CONTENTS Go online for data sheets & assembly instructions. Visit and enter the part number. 73

3 BMA Introduction 50Ω BMA DC 22 GHz GENERAL Blind mate connector Slideon coupling High frequency Float mount design allows large axial and radial misalignment APPLICABLE STANDARDS MILSTD348 Fig. 321 CEI Compatible with OSP series APPLICATIONS Airborne and ground radars Active electronically scanned array antennas Rack and panel telecommunication equipment Military microwave modules Radiall's BMA series has been designed for applications where reliability, durability and performance at high frequency is essential. BMA is a blind mate connector widely used to interconnect microwave modules with multiple coaxial ports. Float mount connectors are recommended for multiple interconnects. Contact Radiall for mounting tolerances. WIDE RANGE The BMA product range consists of cable connectors for flexible cables, semirigid cables and SHF cables, floating bulkhead or flange mount, PCB receptacles, press mount receptacles, screwon receptacles, hermetic receptacles, coaxial contacts for rectangular or circular multipin connectors and adapters. NEW SPRING FINGERS OUTER CONTACT In 2007, a new outer contact was designed and introduced on all BMA female connectors. The new spring fingers outer contact provides improved performance and stability at high frequency up to 22 GHz. Old BMA female part numbers are obsolete and have been replaced with new part numbers which are listed in this catalog. 74 Go online for data sheets & assembly instructions. Visit and enter the part number.

4 Characteristics Test / Characteristics ELECTRICAL CHARACTERISTICS Impedance Frequency range V.S.W.R. Insertion loss (typ.) db RF leakage (min.) db Insulation resistance Contact resistance Values / Remarks 50Ω DC 22 GHz.085"/ RG405 semirigid cable: F (GHz) 0.03 F (GHz) 90 + F (GHz) for gold and BBR connector body 80 + F (GHz) for passivated connector body 5000 MΩ Center contact: 5 mω max. / Outer contact: 2.5 mω max. BMA Voltage in V. RMS At sea level At ft MECHANICAL CHARACTERISTICS Durability Force to engage Force to disengage Dielectric withstanding voltage 1000 V. 200 V. >1000 cycles 13.6 N (3 lbf) max N (0.13 lbf) min. Working voltage 335 V. 85 V. Cable retention force.085"/ RG405 cable.141"/ RG402 cable > 136 N (30 lbf) > 272 N (61 lbf) Center contact retention force Misalignment Radial misalignment Axial misalignment ENVIRONMENTAL CHARACTERISTICS Fixed mount ± 0.1mm (.004 in) 0.38mm (.015 in) max. 27 N (6 lbf) min. Float mount ± 0.51mm (.020 in) 1.52mm (.060 in) min. Temperature range Standard models Semirigid cables 65 C / C 65 C / +105 C Thermal cycling MILSTD202, Method 107, Condition B, 65 C / +125 C Vibration MILSTD202, Method 204, Condition D, 20 g Shock MILSTD202, Method 213, Condition A, 50 g Bumps CECC 22000, Paragraph 4.6.2, 4000 bumps per axis Moisture resistance MILSTD202, Method 106 Corrosion MILSTD202, Method 101, Condition A, 96H Degree of protection MATERIALS AND PLATING Body/Nut Center contacts Material Stainless steel (standard BMA) Brass (commercial BMA) Brass (male) Beryllium copper (female) IP54 (male connector with Oring) Plating Gold or Passivated BBR Gold over Nickel or NPGR Outer contact Beryllium copper NPGR Gaskets Silicon rubber Insulators PTFE Go online for data sheets & assembly instructions. Visit and enter the part number. 75

5 BMA Plugs and Contacts STRAIGHT PLUGS, SOLDER TYPE FOR SEMIRIGID CABLES Fig. 3 Cable group Cable group dia. Fig. Dimension A (mm) Panel drilling Body Finish Captive center contact te RG " RG " R Stainless steel Passivated Yes (epoxy) Crimp type, easy installation R Gold R P01 Brass BBR Yes (4 indents) Oring R Stainless steel Gold Yes (epoxy) R Brass BBR Yes (4 indents) Oring STRAIGHT BULKHEAD PLUGS CRIMP TYPE FOR FLEXIBLE CABLE Fig. 3 Cable group RG174 / RG316 Cable group dia. 2.6/50/S Fig. Dimension A (mm) Panel drilling Body & finish R P02 Stainless steel R passivated R RD /50/D R RG142 / RG223 / RG400 5/50D R Captive center contact Yes (barb) te Waterproof Yes (epoxy) 24.2 P01 3 Brass BBR Yes (4 indents) Oring STRAIGHT CONTACTS SIZE 8 FOR MILSTD38999 CONNECTORS SOLDER TYPE Cable group Cable group dia. Body & finish Fig. Captive center contact Gender R Pin RG " R Stainless steel 2 Socket Yes (epoxy) R gold plated 1 Pin RG " R Socket 76 Go online for data sheets & assembly instructions. Visit and enter the part number.

6 Jacks STRAIGHT FLOATING JACKS SOLDER TYPE FOR SEMIRIGID CABLE BMA Fig. 3 Cable group Cable group dia. Fig. Panel drilling Body & finish Captive center contact Panel mount RG " RG R P03 Stainless steel gold plated Yes (epoxy) 2hole flange R Brass BBR Yes (4 indents) R P18 Bulkhead R P04 Stainless steel gold Snapin R Yes (epoxy) plated R P03 2hole flange R Brass BBR Yes (4 indents) STRAIGHT FLOATING JACKS CRIMP TYPE FOR FLEXIBLE CABLE Cable group Cable group dia. Fig. Panel drilling Body & finish Captive center contact Panel mount RG174 / RG /50S R RD /50D R RG142 / RG223 / RG400 5/50/D R RG174 / RG /50/S R RG142 / RG223 / RG400 5/50/D R RG174 / RG /50/S R RG142 / RG223 / RG400 5/50/D R Brass BBR Yes (4 indents) 1 P03 2hole flange Stainless steel Yes (epoxy) passivated 2 P04 Snapin Go online for data sheets & assembly instructions. Visit and enter the part number. 77

7 BMA Jacks and Receptacles RIGHT ANGLE FLOATING JACKS FOR SEMIRIGID AND FLEXIBLE CABLE Cable group Cable group dia. Fig. Panel drilling Body & finish Captive center contact te RG " R Brass BBR Yes (4 indents) RG " R STRAIGHT SMT MALE RECEPTACLES 1 P03 Stainless steel passivated Yes (epoxy) Solder type R Brass BBR Yes (4 indents) RG142 / RG223 / RG400 5/50/D R Crimp type Fig. Body & finish Captive center contact te R Brass, tin plated Yes (4 indents) R Brass NPGR Tape & Reel 250pcs PCB MALE RECEPTACLES Fig. 3 Fig. 4 Fig. 5 Fig. Panel drilling Body & finish Captive center contact te R Yes (barb) P09 Stainless steel gold plated R Yes (epoxy) R P07 Oring R Brass gold plated Yes (4 indents) Pressfit edgecard type Oring R P07 Oring 5 R P09 Stainless steel gold plated Yes 78 Go online for data sheets & assembly instructions. Visit and enter the part number.

8 Receptacles PCB FEMALE RECEPTACLES BMA Fig. 3 Fig. Panel drilling Body & finish Captive center contact R P09 Brass gold plated Yes (4 indents) R P10 R P11 Stainless steel gold plated Yes (epoxy) NARROW AND SQUARE FLANGE EXTENDED DIELECTRIC MALE RECEPTACLES Fig. 3 Dimension Captive center Fig. Panel drilling Body & finish Panel mount te A (mm) B (mm) contact R Stainless steel passivated Yes (epoxy) 1 P06 4 hole flange R Brass BBR Yes (4 indents) Oring R Stainless steel passivated Yes (epoxy) R P05 R hole flange Brass BBR Yes (4 indents) R R P13 Stainless steel passivated Yes (epoxy) NARROW AND SQUARE FLANGE EXTENDED DIELECTRIC FEMALE RECEPTACLES Fig. Panel drilling Body & finish Captive center contact te R P06 Square flange Stainless steel passivated Yes (epoxy) R P12 2 hole flange Go online for data sheets & assembly instructions. Visit and enter the part number. 79

9 BMA Receptacles SPECIAL FLANGE MALE RECEPTACLE Panel drilling Body & finish Captive center contact te R P16 Stainless steel passivated Turret contact type NARROW FLANGE REPLACEABLE MALE RECEPTACLES Panel drilling Body & finish R R R P13 Stainless steel passivated Captive center contact Yes (epoxy) Accept pin diameter te 0.93 mm EMI gasket 0.3 mm 0.5 mm EMI gasket SCREWON AND PRESSFIT MALE RECEPTACLES Fig. 3 Fig. Panel drilling Body & finish Captive center contact Panel mount te R P14 Cylindrical Screwon R P15 Stainless steel passivated Yes (epoxy) Socket R P08 Pressfit Cylindrical SCREWON HERMETIC RECEPTACLES WITH EMI GASKET (with integrated glass bead) Fig. 3 Fig. Dimension A (mm) B (mm) R R R R R R Body & finish Captive center contact te Stainless steel passivated Stainless steel gold plated Stainless steel passivated Yes Female Male Male, with auxiliary contact, no Oring 710 Go online for data sheets & assembly instructions. Visit and enter the part number.

10 Receptacles FEMALEFEMALE STRAIGHT ADAPTER Body & finish Captive center contact R Stainless steel passivated Yes (epoxy) BMA Panel Drilling P01 P02 P03 P04 P05 P06 P07 P08 P09 P10 P011 P12 P13 P14 P15 P16 Go online for data sheets & assembly instructions. Visit and enter the part number. 711

11 BMA Panel Drilling HERMETIC GLASS BEAD RECEPTACLES P17 INSTALLATION TOOLS FOR HERMETIC RECEPTACLES Body & finish Captive center contact R N.cm Tool for male receptacles R xxx 712 Go online for data sheets & assembly instructions. Visit and enter the part number.

12 Introduction Radiall stainless steel connectors have been designed for applications where reliability, durability, robustness and high frequency are critical. WIDE RANGE The stainless steel range offers cable connectors for both flexible or semirigid cables, panel and PCB mount receptacles, press mount, microstrip, universal, through hole pins and end launch connectors. In series adapters and between series adapters including PUSHON interface are also available. All Radiall stainless steel connectors can be mated with Radiall commercial (brass) connectors. CONVENIENT 3PIECE DESIGN ON MOST CONNECTORS FOR FLEXIBLE CABLES For straight models: single piece body + center contact + outer ferrule For right angle models: single piece body + cap + outer ferrule FAST AND RELIABLE CABLE ATTACHMENT The cable connectors can be either fully crimped or soldered/crimped, offering full flexibility for high volume production with standard manual or pneumatic tooling: fast and reliable. The center contact can be either crimped or soldered The outer contact is attached to the cable by crimping a ferrule SIMPLE SNAPIN CENTER CONTACT CAPTIVATION (FOR FULL CRIMP MODELS) The relative position of the center contact into the interface is mechanically guaranteed by the snapping of the insulator inner shoulder into the groove of the center contact. This design facilitates the captivation operation in contrast of other designs, requiring 2 insulators to provide contact retention. EXTENDED FREQUENCY DC27 GHz Radiall offers an extended frequency range allowing coaxial system operation up to 27 GHz. This series mates with the standard series and maintains the same mechanical characteristics (part numbers ending with 700, 701 or 702). SOLDERLESS ATTACHMENT TO SEMIRIGID CABLE Radiall's crimp connector series offers an exciting alternative for assembling connectors to semirigid cable. The main advantages of these connectors are: time savings, repeatability and performance. Go online for data sheets & assembly instructions. Visit and enter the part number. 713

13 Introduction HERMETIC Hermetic connectors are required to maintain a pressurized or vacuum environment inside a microelectronic package. Radiall offers 3 types of hermetic connectors: 1. Field replaceable hermetic receptacles with separate glass bead (leakage rate below 10 8 atm.cm 3 /sec) The hermeticity level is guaranteed by the glass bead soldered into the package. A large selection of glass beads is available from dia 0.3 to 0.5 mm. They are usually ordered separately from the receptacle. The receptacle can be removed (field replaceable) from the package for maintenance without any risk of leakage. The field replaceable receptacle is recommended when a high number of matings is required. 2. Hermetic receptacles with integrated glass bead (leakage rate below 10 8 atm.cm 3 /sec) The glass bead is already in place inside the receptacle, hermeticity is guaranteed by a solder joint between the receptacle and the package or with a metallic compression gasket. Screwon receptacle with metallic compression gasket offers superior climatic resistance: 65 C +200 C. 3. Hermetic receptacles without glass bead (leakage rate below 10 6 atm/cm 3 /sec) A good hermeticity level is obtained with a metallic gasket at a cost advantage compared to glass beads. 50Ω GENERAL Subminiature coaxial connectors Screwon coupling High RF performance 2 plating options: passivated stainless steel gold plated Wide hermetically sealed range Space qualified range of products extended frequency 27 GHz APPLICABLE STANDARDS MILC39012 EC 1691 CECC CECC to 808 BS 9210 N006 DC 18 GHz DC 27 GHz SPACE QUALIFIED/APPROVALS (For space range) SCC 3402 (ESA) CNES APPLICATIONS Civil & Military Telecommunications Civil & Military Aeronautics Military equipment Space Measurement systems 714 Go online for data sheets & assembly instructions. Visit and enter the part number.

14 Interface PLUG JACK Letter mm inch min. max. min. max. A B C D DIA 4.59 E F DIA 1/4 36 UNS 2B G* H* J K DIA M P DIA 4.10 nom..161 nom. Q DIA S DIA Letter mm inch min. max. min. max. A B C D DIA E DIA F DIA 1/4 36 UNS 2A G* H* J K M P DIA 4.10 nom..161 nom. Q S DIA NOTE: Means behind ref plane Go online for data sheets & assembly instructions. Visit and enter the part number. 715

15 Characteristics ELECTRICAL CHARACTERISTICS Impedance Test / Characteristics Frequency range DC 18 GHz Extended V.S.W.R. (typ.) Straight connector Right angle connector Frequency.085".141" 2.6/50S 5/50S.085".141" 2.6/50S 5/50S 1 GHz GHz Values / Remarks 6 GHz Ω 12.4 GHz GHz GHz Insertion loss (typ.) db Straight connector Right angle connector.085".141" 2.6/50S 5/50S.085".141" 2.6/50S 5/50S F (F in GHz) max RF leakage (db max) Connectors for semirigid cables solder attachment Connectors for flexible cables crimp attachment Receptacles 90 + F (GHz) 60 + F (GHz) F (GHz) Insulation resistance Contact resistance Outer conductor Inner conductor Working voltage in VRMS Sea level ft (21000 m) After tests 4 mω 3 mω.085", RG 405, KS 1.141", RG 402, KS MΩ min RG 174, 188, 316, KX 3, KX 22 Initial 3 mω 2 mω RG 55, 142, 223, KX Dielectric withstanding voltage in VRMS RF testing voltage at in VRMS MECHANICAL CHARACTERISTICS Durability Force to engage and disengage Recommended coupling nut torque Coupling nut retention force Cable retention force Center contact retention force Axial Torque.085", RG 405, KS 1.141", RG 402, KS matings 23 Ncm (2 inch pounds) 80 to 115 Ncm (7 to 10 inch pounds) 270 N (60 Lbs) RG 174, 188, 316, KX 3, KX 22 RG 55, 142, 223, KX N (30 Lbs) 270 N (60 Lbs) 110 N (25 Lbs) 180 N (40 Lbs) 27 N 2.8 N 716 Go online for data sheets & assembly instructions. Visit and enter the part number.

16 Characteristics Test / Characteristics ENVIRONMENTAL CHARACTERISTICS Temperature range Standard models Semirigid cables R Values / Remarks 65 C / C 65 C / +105 C 40 C / +100 C Thermal shock MIL STD 202, method 107, condition B High temperature test MIL STD 202, method 108 Corrosion (salt spray) MIL STD 202, method 101, condition B Vibration MIL STD 202, method 204, condition D, 20g Shock MIL STD 202, method 213 Moisture resistance MIL STD 202, method 106 Hermetic test Down to 10 6 mmhg (Torr) leakage rate < 10 6 atm/cm 3 /sec Barometric pressure MIL STD 202, method 105, condition C MATERIALS AND PLATING Material Plating Body/nut Stainless steel Passivated or gold plated (bodies) Center contacts Beryllium copper (female) Brass (male) Gold plated Gaskets Silicone rubber Insulators PTFE Standard packaging: 100 pieces All dimensions are given in mm. Straight Plugs STRAIGHT PLUGS FOR FLEXIBLE CABLES Fig. 3 A Fig. 4 Fig. 5 Cable group Cable group dia. (Gold) (Passivated) Fig. Dimensions A (mm) Captive center contact Assembly type te RG178 / RG196 2/50/S R Yes Crimp Special 2.2/50/D R Yes Clamp R Yes Single piece body RG174 / RG /50/S R R Crimp Single piece body heatshrink sleeve R R Yes R R Yes Clamp RD /50/D R Single piece body heatshrink sleeve R Yes Single piece body RG58 / RG141 5/50/S R R Yes Crimp RG142 / RG223 / RG400 5/50/D R R R R Yes Single piece body heatshrink sleeve Go online for data sheets & assembly instructions. Visit and enter the part number. 717

17 Straight Plugs STRAIGHT PLUGS FOR FLEXIBLE CABLES (CONT'D) Cable group RG178 / RG196 RD178 RG174/RG316 RD316 RG58/RG141 RG142/RG223/RG400 Cable group dia. 2/50/S 2/50/D 2.6/50/S 2.6/50/D 5/50/S 5/50/D (Gold) (Passivated) STRAIGHT PLUGS SOLDER TYPE FOR SEMIRIGID CABLES Fig. Dimensions A (mm) Dimensions B (mm) Captive center contact Assembly type Crimp Solder Clamp 5 Yes Solder Clamp 5 Yes Crimp Solder Clamp 5 Yes Solder Clamp 5 Yes Crimp Solder Clamp 5 Yes Crimp Solder Clamp 5 Yes Crimp te For passivated version, coupling nut only is passivated Fig. 3 Cable group Cable group dia. RG " RG " (Gold) (Gold/Passivated coupling nut) (Nickel) R R Fig. Dimensions A (mm) Captive center contact R Loose parts R Retractable coupling nut / Single piece body te Single piece body R DC27 GHz Single piece body R R R N/A R R R R N/A Without center contact no Without center contact / Retractable couplingt nut Single piece body Retractable coupling nut / Single piece body DC27 GHz without center contact R N/A Without center contact RG " R Two pieces body 718 Go online for data sheets & assembly instructions. Visit and enter the part number.

18 Straight Plugs STRAIGHT PLUGS SOLDER TYPE FOR SEMIRIGID CABLES (CONT'D) Cable group Cable group dia. RG " (Gold) (Gold/Passivated coupling nut) (Nickel) Fig. Dimensions A (mm) Captive center contact Yes SolderClamp , Yes / For onestep cable assembly te Solder type RG " Yes SolderClamp Yes / For onestep cable assembly Solder type N/A Without center contact STRAIGHT PLUGS CRIMP TYPE FOR SEMIRIGID CABLES Cable group Cable group dia. (gold/passivated coupling nut ) Fig. Ø a Dimensions A (mm) B Captive center contact te RG " R Yes R N/A Retractable coupling nut RG " R N/A Without center contact R Yes Go online for data sheets & assembly instructions. Visit and enter the part number. 719

19 Right Angle Plugs RIGHT ANGLE PLUGS FOR FLEXIBLE CABLES Fig. 3 Cable group Cable group dia. (Gold) (Passivated) Fig. Dimensions (mm) A B Captive center contact Assembly type te RG178 / RG196 2/50/S R Special 2.2/50/D R RG174 / RG /50/S R R RD /50/D R RG58 / RG141 5/50/S R R RG142 / RG223 / RG400 RG178 / RG196 RD178 RG174 / RG316 RD316 RG58 / RG141 RG142 / RG223 / RG400 5/50/D 2/50/S 2/50/D 2.6/50/S 2.6/50/D 5/50/S 5/50/D R R R Crimp Incl. heatshrink tube Yes Clamp Solder Crimp 16.4 Clamp Crimp Incl. heatshrink tube Lock wire hole nut Incl. heatshrink tube Crimp Clamp Solder Crimp Clamp Solder Crimp Clamp Solder Crimp Clamp Solder Clamp Solder Crimp 720 Go online for data sheets & assembly instructions. Visit and enter the part number.

20 Right Angle Plugs RIGHT ANGLE PLUGS FOR SEMIRIGID CABLES Fig. 3 Cable group Cable group dia. (gold) (gold/passivated nut) Fig. Dimensions A (mm) Dimensions B (mm) Captive center contact Assembly type RG " R R RG " R R RG " R RG " R RG " RG " RG " RG " Solder type Crimp type Yes Solder type Solder Clamp Straight Jacks STRAIGHT JACKS FOR FLEXIBLE CABLES Fig. 3 Fig. 4 Cable group RG174 / RG316 RG58 / RG141 RG142 / RG223 / RG400 Cable group dia. 2.6/50/S 5/50/S (Gold) (Passivated) Fig. Dimensions A (mm) Captive center contact Panel drilling R Yes Crimp or solder R R P03 Square flange P03 te Square flange R /50/D R Go online for data sheets & assembly instructions. Visit and enter the part number. 721

21 Straight Jacks STRAIGHT JACKS FOR FLEXIBLE CABLES (CONT'D) Cable group Cable group dia. RG178 / RG196 2/50S RD178 RG174 / RG316 RD316 2/50/D 2.6/50S 2.6/50D RG58 / RG141 5/50S (Gold) (Passivated) Fig. Dimensions A (mm) Captive center contact Panel drilling Crimp type Solder type Yes Crimp type Yes P03 te Crimp type Square flange Solder type Square flange Crimp type Square flange Crimp type Solder type Yes Crimp type Yes P03 Crimp type Square flange Solder type Square flange Crimp type Square flange Crimp type Solder type Yes Crimp type Yes P03 Crimp type Square flange Solder type Square flange Crimp type Square flange Crimp type Solder type Yes Crimp type Yes Yes P03 Crimp type Square flange Solder type Square flange Crimp type Square flange Crimp type Solder type Crimp type Square flange Solder type Square flange RG142 / RG223 / RG400 5/50D Yes Crimp type Square flange Solder type Yes Crimp type Yes 4 21 P03 Crimp type Square flange Solder type Square flange Crimp type Square flange Crimp type 722 Go online for data sheets & assembly instructions. Visit and enter the part number.

22 Straight Jacks STRAIGHT JACKS FOR SEMIRIGID CABLES Fig. 3 Fig. 4 Cable group Cable group dia. RG RG " RG " RG " (Gold) (Passivated) (Nickel) R Fig. Dimensions A (mm) Captive center contact Panel drilling R P03 Square flange 12.7 R te R P02 2 hole flange R P02 2 hole flange R P03 Square flange R Yes Yes / For onestep cable assembly Yes / For onestep cable assembly Yes / For onestep cable assembly Yes P03 P02 Yes / For onestep cable assembly Yes / For onestep cable assembly Yes / For onestep cable assembly Yes P03 P02 Solder type Solder Clamp type Solder type Solder Clamp type Go online for data sheets & assembly instructions. Visit and enter the part number. 723

23 Bulkhead Jacks STRAIGHT BULKHEAD JACKS FOR FLEXIBLE CABLES (rear mount) Fig. 3 Cable group Cable group dia. (Gold) (Passivated) Fig. Dimensions (mm) A B Captive center contact Panel drilling RG178 / RG196 2/50/S R Totally waterproof Crimp and solder R R Heatshrink sleeve RG174 / RG /50/S R Full crimp RD /50/D R Totally waterproof R Yes Full crimp 22.4 R Panel sealed RG58 / RG141 5/50/S R Full crimp R RG142 / RG223 / RG400 5/50/D R Crimp and solder RG178 / RG196 RD178 RG174 / RG316 RD316 RG58 / RG141 RG142 / RG223 / RG400 2/50/S 2/50/D 2.6/50/S 2.6/50/D 5/50/S 5/50/D Crimp type Solder type Crimp type 3 Yes Clamp type Crimp type P06 Solder type Crimp type 3 Yes Clamp type Crimp type Solder type Crimp type 3 Yes Clamp type Crimp type Solder type Crimp type 3 Yes Clamp type Crimp type Solder type Crimp type 3 Yes Clamp type Crimp type Solder type Crimp type 3 Yes Clamp type te 724 Go online for data sheets & assembly instructions. Visit and enter the part number.

24 Bulkhead Jacks RIGHT ANGLE BULKHEAD JACKS CRIMP TYPE FOR FLEXIBLE CABLES (rear mount) Cable group Cable group dia. (Gold) (Passivated) RG178 / RG196 2/50S RD178 2/50D RG174 / RG /50S RD /50D RG58 / RG141 5/50S RG142 / RG223 / RG400 5/50D Captive center contact Panel drilling te Yes P06 Crimp type BULKHEAD JACKS SOLDER TYPE FOR SEMIRIGID CABLES (rear mount) Fig. 3 Cable group Cable group dia. (Gold) (Nickel) (Passivated) Fig. Dimensions A (mm) Dimensions B (mm) Captivecenter contact Panel drilling RG " R Panel sealed R RG " 1 P06 R Unsealed RG " RG " Yes Solder Clamp Yes / for onestep cable assembly P06 Panel sealed te Panel sealed Yes Solder type Yes / for onestep cable assembly Panel sealed Yes Solder Clamp Panel sealed Yes Solder type Go online for data sheets & assembly instructions. Visit and enter the part number. 725

25 Receptacles STRAIGHT FEMALE FLANGE RECEPTACLES SOLDER POT (Gold) (Passivated) Fig. Dimensions (mm) R R R R R A B 0.6 Ø Captive center contact Panel drilling te P04 Square flange Yes (4 indents) P01 2 hole flange Yes P02 STRAIGHT AND RIGHT ANGLE FEMALE SQUARE FLANGE RECEPTACLES SOLDER POT (Gold) (Passivated) R Fig. Dimensions (mm) A B C R Captive center contact Yes Panel drilling P04 P Go online for data sheets & assembly instructions. Visit and enter the part number.

26 Receptacles BULKHEAD FEMALE RECEPTACLE (solder pot) (Gold) (Passivated) R R Fig. Dimensions A (mm) Dimensions B (mm) Captive center contact Yes (2 indents) Panel drilling Front mount P06 Rear mount, Yes panel sealed te Rear mount Right angle front mount SCREWON FEMALE RECEPTACLES (front mount) (gold) Fig. Captive center contact te R Yes Screwon R STRAIGHT MALE FLANGE RECEPTACLES (solder pot) (Gold) Fig. Captive center contact Dimensions A (mm) Panel drilling te R P04 Square flange Yes (4 indents) 17.4 R P01 2 hole flange P03 1/2" Square flange 1 Yes P11 3/8" Square flange Go online for data sheets & assembly instructions. Visit and enter the part number. 727

27 Receptacles SQUARE FLANGE EXTENDED DIELECTRIC FEMALE RECEPTACLES (Gold) (Passivated) R R Dimensions (mm) A B Captive center contact R R Yes (epoxy) R Yes (4indents) R R R R R R R Yes (epoxy) Yes (4 indents) Yes (epoxy) Yes (4 indents) Yes (square flange) Yes (4 incidents) Panel drilling P04 P11 2 HOLE FLANGE EXTENDED DIELECTRIC FEMALE RECEPTACLES (Gold) (Passivated) Dimensions (mm) R R R R R A B Captive center contact Yes (epoxy) Yes (4 indents) Yes (4 indents) Panel drilling P01 RIGHT ANGLE FEMALE SQUARE FLANGE EXTENDED DIELECTRIC RECEPTACLES (Gold) (Passivated) Captive center contact Panel drilling R R Yes P Go online for data sheets & assembly instructions. Visit and enter the part number.

28 Receptacles STRAIGHT MALE FLANGE EXTENDED DIELECTRIC RECEPTACLES (Gold) (Passivated) Fig. Captive center contact Panel drilling te R R P04 Square flange Yes (epoxy) R R P01 2 hole flange PCB FEMALE RECEPTACLES B A Dimensions (mm) Fig. Captive center contact PCB pattern te (Gold) A B R R Yes P05 Selective tin plating R STRAIGHT FEMALE SQUARE FLANGE RECEPTACLES TAB CONTACT Fig. 3 Fig. 4 Fig. 5 (Gold) (Passivated) Fig. Dimensions A (mm) Captive center contact Panel drilling Contact type R R R R P04 R R P11 R Yes (epoxy) R P04 R R P11 Offset tab Tab Go online for data sheets & assembly instructions. Visit and enter the part number. 729

29 Receptacles STRAIGHT AND RIGHT ANGLE FEMALE 2 HOLE FLANGE RECEPTACLES TAB CONTACT Fig. 3 Fig. 4 Fig. 5 (Gold) (Passivated) Fig. Captive center contact Panel drilling Contact type R Offset tab R Yes (epoxy) P01 Special R Tab P03 Yes P01 Tab contact 1.3mm width STRAIGHT MALE SQUARE FLANGE RECEPTACLES TAB CONTACT (Gold) (Passivated) Captive center contact Panel drilling te R R Yes (epoxy) P04 Unit packaging STRAIGHT FEMALE SQUARE FLANGE RECEPTACLES CYLINDRICAL CONTACT (Gold) Captive center contact Panel drilling te R Yes (epoxy) P04 Unit packaging 730 Go online for data sheets & assembly instructions. Visit and enter the part number.

30 Receptacles for Microstrip STRAIGHT FEMALE FLANGE RECEPTACLES CYLINDRICAL CONTACT Dimensions (mm) Fig. (Gold) (Passivated) A B C R R R R R R R Captive center contact Yes Panel drilling te Captivation P04 Square flange 4 indents P01 2 hole flange Epoxy STRAIGHT MALE FLANGE RECEPTACLES CYLINDRICAL CONTACT (Gold) (Passivated) Fig. Captive center contact Panel drilling te R R P04 Square flange Yes (epoxy) R R P01 2 hole flange Go online for data sheets & assembly instructions. Visit and enter the part number. 731

31 Receptacles for Microstrip UNIVERSAL FIELDREPLACEABLE RECEPTACLES FEMALE SOCKET (accept pin 0.93 mm [.037"]) Fig. 3 Fig. 4 Fig. 5 (Gold) (Passivated) Fig. Captive center contact Panel drilling te R R Female Square flange P04 R Male Square flange Yes (epoxy) R R Female 2 hole flange Unit packaging P01 R Male 2 hole flange R P04 Female Right angle square flange EDGE CARD RECEPTACLES (Gold) (Passivated) Fig. Captive center contact te Captivation R Solder pins 4 indents Yes R R screws Epoxy 732 Go online for data sheets & assembly instructions. Visit and enter the part number.

32 Hermetic Receptacles with Separate Glass Bead SQUARE FLANGE 12.7 mm FEMALE RECEPTACLE (Gold) (Passivated) Glass bead only Dimensions (mm) A B C D EMI gasket only R R R R Panel drilling connector Panel drilling glass bead Diameter pin = 0.45 P10 P Diameter pin = 0.30 te Diameter pin = Diameter pin = 0.38 NARROW FLANGE FEMALE RECEPTACLES (Gold plated) (Passivated) Glass bead only Dimensions (mm) A B C EMI gasket only Panel drilling connector Panel drilling glass bead R R R P R P12 R R R P Diameter Pin EMI (included) = gasket (included) Diameter Pin (included) Contact Us P12 = 0.38 NARROW FLANGE MALE RECEPTACLES te (Passivated) Glass bead only EMI gasket only Panel drilling connector Panel drilling glass bead R R P13 R R R P12 P Contact Us Go online for data sheets & assembly instructions. Visit and enter the part number. 733

33 Hermetic Receptacles with Integrated Glass Bead SCREWON TYPE FEMALE RECEPTACLES (Passivated) Glass bead only Fig. Assembly tool Panel drilling glass bead te R R P15 For pin dia 0.3/ R R R P19 For pin dia 0.5/0.19 R R P15 Supplied with glass bead SOLDER TYPE FEMALE RECEPTACLE Panel feedthrough receptacles feature an internal hermetic glass bead. A ring of solder between the receptacle body and the package will provide the hermeticity level. (Gold) Connector body Panel drilling Contact type R FN42 alloy Cylindrical R Stainless steel SCREWON TYPE FEMALE RECEPTACLE Screwon receptacles with integrated glass seal the compression gasket will ensure the hermeticity between the receptacle and the package. 1.7 DIA 0.5 DIA Compression gasket (Gold) (Passivated) Connector body Panel drilling Contact type R R Stainless steel P05 Cylindrical SCREWON TYPE FEMALE RECEPTACLE WITH SLIDING CONTACT (Passivated) Fig. Connector body Panel drilling Contact type R Stainless steel P05 Cylindrical R Go online for data sheets & assembly instructions. Visit and enter the part number.

34 Hermetic Receptacles without Glass Bead SCREWON TYPE FEMALE RECEPTACLE WITH SLIDING CONTACT Screwon receptacles without glass bead provide a lower hermeticity level (10 6 atm/cm3/sec). A gasket is provided to guarantee the hermeticity between the receptacle and the package. (Gold) (Passivated) Panel drilling Contact type R R P08 Slotted Adapters IN SERIES ADAPTERS Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. Dimensions (mm) Captive center Panel (Gold) (Passivated) A B contact drilling te R R Male Male R R Yes (4 indents) Male Female R R Female Female R R Yes (epoxy) P06 Bulkhead female Female R R Yes P08 Bulkhead hermetically sealed Female Female R R Right angle male Female R Pushon male 7 Yes (epoxy) R P07 Pushon female R P06 Female Female square flange adapter Bulkhead female Female Male Female Female Female Yes (4 indents) Male Male Male Female / Right angle Male Male / Right angle Male Male / Right angle Go online for data sheets & assembly instructions. Visit and enter the part number. 735

35 Adapters TEE IN SERIES ADAPTERS (Gold) (Passivated) Fig. Type Captive center contact R R Male / Female Female R R Female / Female Female Yes Accessories MALE AND FEMALE CAPS Fig. 3 (Gold) (Passivated) Fig. te R R Male R R Male with chain R R Male short circuit R R Female with cord CENTER CONTACTS (To be used with universal receptacle) center contact removable insulator (optional) receptacle PCB Microelectronic package Fig. 3 Fig. Termination Dimensions (mm) A B C Packaging R Tab R Tab special x W R Tab R Cylindrical 1.77 dia pieces A C B R Cylindrical 3.37 dia R Tab special x W Go online for data sheets & assembly instructions. Visit and enter the part number.

36 Glass Beads GLASS BEADS FOR HERMETIC RECEPTACLES Hermeticity guaranteed at 10 8 atm.cm 3 /s Dimensions mm (inch) A B C D E Packaging R (.180) 1 R (.012) 2.52 (.099) 1.60 (.063) 1.3 (.051) 1.83 (.072) 100 R (.180) 1 R (.076) 0.38 (.015) 2.50 (.098) 156 (.061) 1.59 (.062) 100 R (.051) R (.112) 0.46 (.018) 1.60 (.063) 1 R (.111) 4.57 (.180) 1.83 (.072) R (.070) 2.03 (.080) (.019) 4 (.157) 1.77 (.070) R (.230) 1.93 (.076) 1 Go to page 1718 for more glass beads. SOCKET OPTION CONNECTOR GLASS BEAD PCB MICRO ELECTRONIC PACKAGE EMI /RFI GASKET WITHOUT SOCKET OPTION WITH SOCKET OPTION Go online for data sheets & assembly instructions. Visit and enter the part number. 737

37 Accessories for Hermetic Microstrip Receptacles OPTIONAL SOCKET 0.85 DIA Accepts ADIA contact A Dia (mm) Packaging R R pieces Go to chapter 19A for more socket contact options. For use with glass seal. Panel Drilling PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 P10 P11 P Go online for data sheets & assembly instructions. Visit and enter the part number.

38 Panel Drilling HERMETIC SEPARATE GLASS BEAD RECEPTACLES P13/14 Adia. Bdia. 256UNC2B (do not break thr.) Cdia P13 P14 Adia. 2.6 ± ±0.025 Bdia ± ±0.025 Cdia. Ldia. (1) 2 ±0.02 (2) 0.7 ± ±0.02 (1) 2.5 ±0.1 (2) from 1mmto4mm (1) Using of the removable contact. (2) The pin isdirectly welded on the trace. P15/16 P15 P16 Adia. 2.6 ± ± /4 36 UNS 2B dia dia. ±0.025 Bdia. Adia. Cdia Bdia ± ±0.025 Cdia. Ldia. (1) 2 ±0.02 (2) 0.7 ± ±0.02 (1) 2.5 ±0.1 (2) from 1mmto4mm (1) Using of the removable contact. (2) The pin isdirectly welded on the trace. P17 P ± to DIA ± UNC2B (do not break thr.) 6.6 DIA DIA. ± DIA. ± DIA ± DIA DIA. ±0.025 Go online for data sheets & assembly instructions. Visit and enter the part number. 739

39 Panel Drilling HERMETIC SEPARATE GLASS BEAD RECEPTACLES P19 P to DIA DIA. ± DIA. ± DIA DIA. ± DIA. ± DIA ±0.025 According customer application ±0.025 Tooling for Hermetic Receptacles Coupling torque: 190 cm N Coupling torque: 280 cm N R R Description Installation tool for jack receptacles R R R R Description Installation tool for jack receptacles R R R R R R R R R Go online for data sheets & assembly instructions. Visit and enter the part number.

40 Field Replaceable Hermetic Microstrip Receptacle Information ELECTRICAL PERFORMANCE V.S.W.R. to 18 GHz Connector only Seal only Connector & seal F (GHz) F (GHz) F (GHz) V.S.W.R. MEASUREMENT Setting for V.S.W.R. measurement on field replaceable hermetic receptacle a) Measurement with auxiliary contactassembly drawing R (for pin DIA 0.30 mm) R (for pin DIA 0.46 mm) b) Measurement without auxiliary contactassembly drawing Recommended value :L1 = 1.0 mm L1 =1.0 to 4.0 Ceramic thickness 0.38 Ceramic The track width on ceramic defines the circuit impedance. Go online for data sheets & assembly instructions. Visit and enter the part number. 741

41 Field Replaceable Hermetic Microstrip Receptacle Information GLASS BEAD AND CONNECTOR ASSEMBLY INTO THE MICRO ELECTRONIC PACKAGE X = 2.0 ± 0.5 X = L1 + A removable socket solder solder solder with socket option without socket option GLASS BEAD 1. Adjust X by cutting the pin if necessary 2. Introduce the glass bead into its cavity 3. Place a ring of solder in the groove around the glass bead (a 0.3 mm wire dia. of solder is recommended) 4. Solder the pin (or optional socket) on the PCB trace inside the package te: there is not too much welding. IMPORTANT: For maximum RF performance, the link track/pin must be as thin as possible. Therefore, we advise to follow the A dimension rigorously, by soldering accurately the pin or the socket directly on the trace. CONNECTOR RECEPTACLE Place the EMI screening gasket in the groove of the receptacle (if applicable). Introduce gently the receptacle on the glass bead pin, then screw the flange (use the appropriated tool for screwin receptacle). GLASS BEAD MOUNTING Version with additional machining Version without RIGHT BAD The Radiall panel drilling on page 827 recommends an additional bore or chamfer machining on the outer edge of the glass bead housing. This additional machining allows to place a preform (solder stick Dia. 0.3 mm) before soldering. After mounting, solder is flush and allows the right positioning of the receptacle. The EMI gasket efficiency is guaranteed. 742 Go online for data sheets & assembly instructions. Visit and enter the part number.

42 Introduction Radiall Commercial connectors are specially designed for applications where low installation cost are most important. They are easy, fast to assemble and reliable, and offer the perfect solution for high volume applications requiring high level performance such as in civil telecommunications, data communications or test and measurement. Full compatibility: Commercial connectors are fully compatible (interchangeable and intermateable) with all existing MIL standardized connectors. They feature the same performance level except for mechanical characteristics (life: 100 matings and coupling nut torque: 60 Ncm). The coupling nut of Commercial connectors features a special design which is different from the standard coupling nut as the tightening torque is reduced. Wide range: The Commercial series offers a wide range of solutions which are for every standard coaxial flexible or semirigid cable as well as PCB models with traditional throughhole pins or solder pads for SMT applications. Simple snapin axial captivation (for full crimp models): The relative position of the center contact into the interface is mechanically guaranteed by the snapping of the insulator inner shoulder into the groove of the center contact. This design facilitates the captivation operation in contrast to other designs, requiring two insulators to provide contact retention. It assures constant and perfect axial positioning of the center contact into the interface. Spacesaving size: Due to the captivation technique, these commercial connectors are shorter than multipiece body connectors. Convenient 3piece design: For straight models: body + center contact + outer ferrule For right angle models: single piece body + back cap + outer ferrule Fast and reliable cable attachment: The cable connectors can be either fully crimped or soldered/crimped, offering full flexibility for high volume industrial production with standard manual or pneumatic tooling: fast and reliable The center contact can be either crimped or soldered The outer contact is attached to the cable by crimping a ferrule Competitive pricing: The design and materials used in the manufacturing of the Commercial series allow us to offer connectors at competitive prices to suit a wide range of applications. The connector body is manufactured in brass and the surface plating is available in either gold or in BBR finish (Radiall nonmagnetic bright bronze surface finish). Center contact captivation: Our connectors have a captive center contact. COM Go online for data sheets & assembly instructions. Visit and enter the part number. 743

43 COM Introduction 50Ω GENERAL Subminiature coaxial connectors Screwon coupling High RF performance 2 plating options: BBR Gold APPLICABLE STANDARDS MILC39012 IEC 1691 CECC CECC to 808 BS 9210 N006 APPLICATIONS Telecommunications Aeronautics Measurement and Test systems General electronics DC 18 GHz 744 Go online for data sheets & assembly instructions. Visit and enter the part number.

44 Interface PLUG JACK COM Letter mm inch min. max. min. max. A B C D DIA 4.59 E DIA F DIA 1/4 36 UNS 2B G* H* J K DIA M P DIA 4.10 nom..161 nom. Q DIA S DIA Letter mm inch min. max. min. max. A B C D DIA E DIA F DIA 1/4 36 UNS 2A G* H* J K M P DIA 4.10 nom..161 nom. Q S DIA NOTE: Means behind ref plane Go online for data sheets & assembly instructions. Visit and enter the part number. 745

45 COM Characteristics GENERAL Impedance 50Ω Frequency range Test / Characteristics Semirigid cables DC 18 GHz Standard models DC 12.4 GHz Temperature range 65 C C 65 C C ELECTRICAL CHARACTERISTICS Insulation resistance MΩ mini. Contact resistance Outer conductor Inner conductor V.S.W.R. max up to: 18 GHz for semirigid cable 12.4 GHz for right angle connector (SR) 12.4 GHz for flexible cable Straight Connector Right angle connector MILC39012 paragraph 316 Initial 3 mω 2 mω After test 4 mω 3 mω ".141" 2.6/50/S 5/50/D F F Values / Remarks F F F F F F Dielectric withstanding voltage in VRMS Working voltage in VRMS (sea level) Working voltage in VRMS ( ft) RF testing voltage at 5 MHz in VRMS MECHANICAL CHARACTERISTICS Cable retention force ".141" 2.6/50/S 5/50/D 130 N 270 N 90 N 204 N Life matings Force to engage and disengage Ncm 2 inch pounds Coupling nut torque recommended 60 Ncm 5.2 inch pounds Coupling nut retention force N min ENVIRONMENTAL CHARACTERISTICS Vibration 318 MIL STD 202, method 204, condition D,20g Shock 319 MIL STD 202, method 213, condition I,100g Thermal shock 320 MIL STD 202, method 107, condition B, Corrosion (salt spray) 313 MIL STD 202, method 101, condition B, Moisture resistance 321 MIL STD 202, method 106 Barometric pressure 322 MIL STD 202, method 105, condition C Hermetic test Down to 10 6 mmhg (Torr) leakage rate < 10 8 atm/cm 3 /sec Life (at high temperature) MIL STD 202, method 108 MATERIALS AND PLATING Material Plating Bodies Brass BBR* or Gold plated Center contacts Beryllium copper (female) Brass (male) Gold plated Insulators PTFE teflon Gaskets Silicone rubber *BBR: Bright Bronze Radiall All dimensions are given in mm. Standard packaging: 100 pieces 746 Go online for data sheets & assembly instructions. Visit and enter the part number.

46 Plugs STRAIGHT PLUGS, FULL CRIMP TYPE FOR FLEXIBLE CABLE Cable group Cable group dia. 7 / 2 Flats ØD (Gold) Hex. 7/flats (BBR) RG178 / RG196 2/50/S R R Fig. ØD Dimensions (mm) Captive center A D contact A te Back nut / Solder contact COM RG174 / RG /50/S R R RD /50/D R RG58 / RG141 5/50/S R R RG142 / RG223 / RG400 5/50/D R R Yes AEP195FR LMR 195 R AEP200FR LMR 200 R AEP240FR LMR 240 R Crimp type AEP400FR LMR 400 R STRAIGHT PLUGS, SOLDER TYPE FOR SEMIRIGID CABLE Hex. 8/flats Hex. 8/flats Cable group Cable group dia. (Gold) Fig. A A Dimensions A (mm) Captive center contact RG R RG R Yes R Go online for data sheets & assembly instructions. Visit and enter the part number. 747

47 COM Plugs and Jacks RIGHT ANGLE PLUGS Cable group Cable group dia. (Gold) (BBR) Fig. RG174 / RG316 / AEP100FR 2.6/50/S & LMR 100 R R RD /50/D R R RG58 / RG141 5/50/S R R RG142 / RG223 / RG400 5/50/D R R AEP195FR LMR 195 R Dimensions (mm) AEP200FR LMR 200 R AEP240FR LMR 240 R B A B te Crimp type for flexible cable Crimp type RG " R R Solder type for 2 RG R R semirigid cable A Hex. 8/flats Hex. 8/flats STRAIGHT JACKS Hex. 7/flats 6 /2 flats Ø Cable group Cable group dia. (Gold) RD /50/D R RG174 / RG /50/S R Fig. Captive center contact te 1 Yes Full crimp type for flexible cable RG R Solder type for semirigid cable 748 Go online for data sheets & assembly instructions. Visit and enter the part number.

48 Jacks BULKHEAD FEEDTHROUGH STRAIGHT JACKS, FULL CRIMP TYPE, FOR FLEXIBLE CABLE Cable group Hex. 8/ flats 5.6 / 2 flats Cable group dia (Gold) Hex. 8/ flats (BBR) Fig. Hex. 8/ flats 5.9 / 1 flat Dimensions A (mm) Panel drilling RG178 / RG196 2/50/S R P06 RG174 / RG316 / AEP100FR 2.6/50/S & LMR 100 R R RG 58 / RG141 5/50S R RG142 / RG223 / RG400 5/50/D R P A Captive center contact Yes Hex. 8/ flats te Reverse crimping / Solder contact 25.4 Full crimp type COM BULKHEAD FEEDTHROUGH STRAIGHT JACKS, SOLDER TYPE, FOR SEMIRIGID CABLE PANEL SEAL Hex. 8 / flats 5.9 / 1 flat 2.4 Hex. 11 / flats 16 Cable group Cable group dia. (Gold) RG R RG R Panel drilling P05 Captive center contact FLANGE JACKS, SOLDER TYPE FOR SEMIRIGID CABLE Ø holes Ø holes Ø Ø Cable group Cable group dia. RG (Gold) Fig. Panel drilling R P04 R RG R P02 Captive center contact Go online for data sheets & assembly instructions. Visit and enter the part number. 749

49 COM Receptacles SQUARE FLANGE FEMALE RECEPTACLES Fig Dimensions (mm) A B C R R R Ø1.27 R BBR Ø Fig. 3 Panel drilling Finish Captive center contact P Gold 8.64 Ø16 4 holes Ø2.6 Yes (4 indents) to NARROW FLANGE FEMALE RECEPTACLES Ø Ø1.27 Ø0.8 Ø4.06 Ø holes Ø2.6 B A Dimensions (mm) Fig. Panel drilling Finish Captive center contact A B R Gold P04 Yes (4 indents) R BBR RIGHT ANGLE SQUARE FLANGE FEMALE RECEPTACLES 4 holes Ø Ø1.27 Ø Ø16 B Panel drilling Finish R P02 Gold 750 Go online for data sheets & assembly instructions. Visit and enter the part number.

50 Switches STRAIGHT FEMALE PCB RECEPTACLES AND SWITCHES Ø8.25 Ø COM 1 Ø Ø1.27 Fig. 3 Ø1.27 Fig. 4 Fig. 5 Fig. Panel drilling Assembly instructions R M03 Finish R M02 Gold SMT edge card type Packaging: unit te Switch edge card SMT Right type Packaging in Reel 110 pieces R R BBR 4 P03 R R Gold Surface mount / Bulkhead 100 pieces 5 M01 R Surface mount / Tape & Reel 100 pieces RIGHT ANGLE FEMALE PCB RECEPTACLES Ø8.26 Ø Ø Fig. 3 Fig Ø1.27 Fig. Panel drilling Assembly instructions Finish te R P07 Gold Packaging: tray 60 pieces R BBR 2 P03 R R M01 Gold Surface mount / Bulkhead 100 pieces R M04 Packaging: Tape & Reel 100 pieces Go online for data sheets & assembly instructions. Visit and enter the part number. 751

51 COM Receptacles MALE CAP Finish te R Tin chain ADAPTERS For in series adapters, please see standard. Panel Drilling PO1 PO2 PO3 PO4 PO5 PO6 PO7 A DI mm M axi mini A Go online for data sheets & assembly instructions. Visit and enter the part number.

52 Assembly Instructions M01 SOLDERING PATTERN R R COPLANAR LINE Pattern and signal are on the same side Thickness of PCB: 1.6 mm The PCB material is made of epoxy resin of glass fabrics bacs (Er = 4.8) The solder resist should be printed except for the land pattern on the PCB R COM VIDEO SHADOWS M02 SOLDERING PATTERN R COPLANAR LINE Pattern and signal are on the same side Thickness of PCB:.063 (1.6 mm) The PCB material is made of epoxy resin of glass fabrics bacs. (Er = 4.8) The solder resist should be printed except for the land pattern on the PCB VIDEO SHADOW Go online for data sheets & assembly instructions. Visit and enter the part number. 753

53 COM Assembly Instructions M03 PCB FOR SWITCH plated holes Ø0.80 ground report ground The ground is on the botton of PCB thickness of PCB: 1.6mm material: FR4(er=4.6) R VIDEO SHADOW M04 SOLDERING PATTERN VIDEO SHADOW R COPLANAR LINE Pattern and signal are on the same side Thickness of PCB:.063 (1.6 mm) The PCB material is made of epoxy resin of glass fabrics bacs. (Er = 4.8) The solder resist should be printed except for the land pattern on the PCB 754 Go online for data sheets & assembly instructions. Visit and enter the part number.