Analog Flat Panel Monitor

Transcription

1 Analog Flat Panel Monitor Regular and High Brightness Installation and Operations Manual For use with models: LM9001 LM8001 LM6001 LM9006 LM8006 LM6006 LS9001 LS8001 LS6001 LS9006 LS8006 LS6006 DOC-IWS-641 Nematron Corporation 5840 Interface Drive Ann Arbor, MI Copyright 2002 Nematron Corporation

2 Copyright Notice This document and product is copyrighted, August 2002 by Nematron Corporation. All rights are reserved. No part of this manual may be reproduced, copied, or translated without permission from Nematron Corporation. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products. This manual is subject to change without notice.

3 Table of Contents Chapter 1: Product Information General Product Specifications LM9000 / LS9000 (17-inch) Dimensions LM9000 Specifications LS9000 Specifications Optional Touchscreen Environmental LM8000 / LS8000 (15-inch) Dimensions LM8000 Specifications LS8000 Specifications Optional Touchscreen Environmental LM6000 / LS6000 (12.1-inch) Dimensions LM6000 Specifications LS6000 Specifications Optional Touchscreen Environmental Chapter 2: Monitor Installation Cable Connections LCD without Touch Screen LCD with Touch Screen Panel Mounting Arm Mounting Wall Mounting LM9000 / LS9000 (17-inch) Wallmount LM8000 / LS8000 (15-inch) Wallmount LM6000 / LS6000 (12.1-inch) Wallmount Rack Mounting LM9000 / LS9000 (17-inch) Rackmount LM8000 / LS8000 (15-inch) Rackmount LM6000 / LS6000 (12.1-inch) Rackmount Chapter 3: User Mode OSD Information LM9000 / LS9000 and LM8000 / LS Features Button Functions User Mode OSD Structure User Mode OSD Item Description LM6000 / LS Features

4 3.2.2 Button Functions User Mode OSD Structure User Mode OSD Item Description

5 Chapter 1: Product Information 1.1 General Product Specifications Nematron Analog Flat Panel Industrial Monitors offer three different display sizes and resolutions, two different brightness options and multiple mounting options to meet your needs. All of these flat panel monitors are specially designed to meet the requirements of industrial environments. Suitable for panel mounting and 75/100mm interface pads for arm mounting (conform to the proposed VESA standard) Panel Interface for 15 and 17 models: DVI and Analog VGA signal (by AV-0911 DVI and Analog VGA to Digital LCD Interface Board) Panel Interface for 12.1 model: Analog VGA signal (by AV-9261 Analog VGA to Digital LCD Interface Board) DVI (Digital Video Interface) input (optional for 15 and 17 models only) o o o Sync Detect: for Plug & Display. Cable Distance Support: over 3m with twisted-pair Compliant with DVI 1.0: DVI is backwards compatible with VESA P&D and DFP. Front On Screen Display (OSD) control keys to adjust for the best display quality. Side cabling design to reduce the LCD monitor s total depth Aluminum front panel Ships with power adapter for VAC input 3

6 1.2 LM9000 / LS9000 (17-inch) Dimensions The following diagrams indicate the dimensions of LM9000. The depth of the High Brightness LS9000 is 70.8 mm rather than the 50.8 mm shown for the LM9000. Width Height Depth Bezel in (452.0 mm) in (355.5 mm) 0.39 in (10.0 mm) Chassis, LM in (422.0 mm) in (327.6 mm) 2.00 in (50.8 mm) Chassis, LS in (422.0 mm) in (327.6 mm) 2.79 in (70.8 mm) Cutout in (424.0 mm) in (329.5 mm) n/a 4

7 1.2.2 LM9000 Specifications Display Model 17 LCD Support digital input by DVI connector and VGA connector Resolution: 1280 x 1024 Max. Colors: 16.7 million Brightness: 250cd/m 2 Vertical viewing angle: 160 Horizontal viewing angle: 160 LCD MTBF: 50,000 hrs Backlight MTBF: 25,000 hrs Power Supply Input requirements: Input Voltage range: 90 to 264 VAC Line frequency: 47 to 63 HZ Output: Output Voltage range: +12V ±0.5V, 3.8A, 45 Watt Ripple and Noise: Voltage 120 mvp EMI emissions: The power supply meets the radiated and conducted emission requirements for CISPR22 CLASS B and FCC CLASS B. MTBF: When the power supply is operated within any of the limits of this power supply s specification, the MTBF shall be at least (50,000) hours at 25 C. System Power Consumption: 12V / 1.8A (not including touchscreen) LS9000 Specifications Display Model 17 High Brightness LCD Support digital input by DVI connector and VGA connector Resolution: 1280 x 1024 Max. Colors: 16.7 million Brightness: 725 cd/m 2 Horizontal viewing angle: 160 Vertical viewing angle: 160 LCD MTBF: 50,000 hrs Backlight MTBF: 20,000 hrs Power Supply Input requirements: Input Voltage range: 100 to 240 VAC Line frequency: 47 to 63 HZ; 1.9A Output: Output Voltage range: +12V ±1.0V, 7.27A, 80 Watt Ripple and Noise: Voltage 120 mvp EMI emissions: The power supply meets the radiated and conducted emission requirements for CISPR22 CLASS B and FCC CLASS B. MTBF: When the power supply is operated within any of the limits of this power supply s specification, the MTBF shall be at least (50,000) hours at 25 C. System Power Consumption: 12V / 4.8A (not including touchscreen) 5

8 1.2.4 Optional Touchscreen 17 Touch Screen Type: Analog Resistive Resolution: Continuous Light transmission: Typical value 75% Surface Hardness: 4H or more (Test according to: ASTM D A) 8-wire touch screen Touch screen interface: RS-232 Supported operating systems: Linux, MS-DOS, Windows 3.1, Windows 95/98/ME, Windows NT/2000/XP, OS/2, Macintosh Environmental LM9000 Operating Temperature: 0 to 50 C LS9000 Operating Temperature: 0 to 40 C Relative Humidity: 10 to 95%, non-condensing Storage Temperature: -20 to 60 C Vibration: 5-17Hz, 0.1" double amplitude displacement; Hz, 1.5G acceleration peak to peak Shock: 10G acceleration peak to peak 6

9 1.3 LM8000 / LS8000 (15-inch) Dimensions The following diagram indicates the dimensions of LM8000. The depth of the High Brightness LS8000 is 56.1 mm rather than the 43.7 mm shown for the LM8000. Width Height Depth Bezel in (410.0 mm) in (309.0 mm) 0.35 in (9.0 mm) Chassis, LM in (383.6 mm) in (282.6 mm) 1.84 in (46.7 mm) Chassis, LS in (383.6 mm) in (282.6 mm) 2.21 in (56.1 mm) Cutout in (386.8 mm) in (285.8 mm) n/a 7

10 1.3.2 LM8000 Specifications Display Model 15 TFT LCD Resolution: 1024 x 768 MAX. Colors: 16.7 M Luminance: 200 cd/m 2 Operating Temperature: 0 to 50 C Storage Temperature: -20 to 60 C Viewing Angle: R/L: 120, U/D: 100 LCD MTBF: 50,000 hrs Backlight MTBF: 25,000 hrs Power Supply Input requirements: Input Voltage range: 90 to 264 VAC. Line frequency: 47 to 63 HZ. In-Rush current: 80 A max. Input current: 1.4 A max. Output: Output Voltage range: +11.4V to +12.6V (tolerance: ±5%) 3.8A 45 Watt Ripple and Noise: Voltage +12V Maximum peak to peak ripple and noise: 120mV EMI emissions: The power supply meets the radiated and conducted emission requirements for a (CISPR22 CLASS B) and a (FCC CLASS B). MTBF: When the supply is operated within any of the limits of this power supply s specification, the MTBF shall be at least (50,000) hours at 25 C. System Power Consumption: 12V / 1.2A LS8000 Specifications Display Model 15 high brightness TFT LCD Resolution: 1024 x 768 MAX. Colors: 16.7 M Luminance: 1750 cd/m 2 Viewing Angle (degree): R/L:120 U/D:100 LCD MTBF: 50,000 hrs Backlight MTBF: 30,000 hrs Power Supply Input requirements: Input Voltage range: 90 to 264 VAC. Line frequency: 47 to 63 HZ. In-Rush current: 30A 115VAC, 60A max@230vac at 25 C. Input current: 1.5 A 115VAC, 0.8A max@230vac. Output: Output Voltage range: +12V ±0.5V 3.8A 45 Watt Ripple and Noise: Voltage 120 mvp EMI emissions: The power supply meets the radiated and conducted emission requirements for CISPR22 CLASS B and FCC CLASS B. MTBF: When the supply is operated within any of the limits of this power supply s specification, the MTBF shall be at least (50,000) hours at 25 C. System Power Consumption: 12V / 4.3A 8

11 1.3.4 Optional Touchscreen 15 Touch Screen Type: Analog Resistive Resolution: Continuous Light transmission: Typical value 75% Surface Hardness: 4H (Test condition: ASTM D A) 8-wire touch screen Touch screen controller: RS-232 Supported operating systems: Linux, MS-DOS, Windows 3.1, Windows 95/98/ME, Windows NT/2000/XP, OS/2, Macintosh, etc Environmental LM8000 Operating Temperature: 0-50 C LS8000 Operating Temperature: 0-40 C Relative Humidity: 10 95%, non-condensing Storage Temperature: C Vibration: 5-17Hz, 0.1" double amplitude displacement; Hz, 1.5G acceleration peak to peak Shock: 10G acceleration peak to peak 9

12 1.4 LM6000 / LS6000 (12.1-inch) Dimensions The following diagrams indicate the dimensions of LM6000. The depth of the High Brightness LS6000 is 56.6 mm rather than the 43.7 mm shown for the LM6000. Width Height Depth Bezel in (340.0 mm) in (260.0 mm) 0.35 in (9.0 mm) Chassis, LM in (310.0 mm) 9.06 in (230.0 mm) 1.72 in (43.7 mm) Chassis, LS in (310.0 mm) 9.06 in (230.0 mm) 2.23 in (56.6 mm) Cutout in (312.0 mm) 9.13 in (232.0 mm) n/a 10

13 1.4.2 LM6000 Specifications Display Model 12.1 TFT Resolution: 800 x 600 MAX. Colors: 18 bits Luminance: 250 cd/m 2 Viewing Angle (degree): R/L:180 U/D:30 LCD MTBF: 50,000 hrs Backlight MTBF: 30,000 hrs Power Supply Input requirements: Input Voltage range: 90 to 264 VAC. Line frequency: 47 to 63 HZ. In-Rush current: 80 A max. Input current: 1.4 A max. Output: Output Voltage range: +11.4V to +12.6V (tolerance: ±5%) 3.8A 45 Watt Ripple and Noise: Voltage +12V Maximum peak to peak ripple and noise: 120mV EMI emissions: The power supply meets the radiated and conducted emission requirements for CISPR22 CLASS B and FCC CLASS B. MTBF: When the supply is operated within any of the limits of this power supply s specification, the MTBF shall be at least (50,000) hours at 25 C. System Power Consumption: 12V / 1.3A LS6000 Specifications Display Model 12.1 high brightness TFT LCD Resolution: 800X600 MAX. Colors: 18 bits Luminance: 1308 cd/m 2 Viewing Angle (degree): R/L:180 U/D:30 LCD MTBF: 50,000 hrs Backlight MTBF: 20,000 hrs Power Supply Input requirements: Input Voltage range: 90 to 264 VAC. Line frequency: 47 to 63 HZ. In-Rush current: 30A 115VAC, 60A max@230vac at 25 C. Input current: 1.5 A 115VAC, 0.8A max@230vac. Output: Output Voltage range: +12V ±0.5V 3.8A 45 Watt Ripple and Noise: Voltage 120 mvp EMI emissions: The power supply meets the radiated and conducted emission requirements for a (CISPR22 CLASS B) and a (FCC CLASS B). MTBF: When the supply is operated within any of the limits of this power supply s specification, the MTBF shall be at least (50,000) hours at 25 C. System Power Consumption: 12V / 2.4A (not including touchscreen) 11

14 1.4.4 Optional Touchscreen 12.1 Touch Screen Type: Analog Resistive Resolution: Continuous Light transmission: Typical value 75% Surface Hardness: 4H (Test condition: ASTM D A) 8-wire touch screen Touch screen controller: RS-232 Supported operating systems: Linux, MS-DOS, Windows 3.1, Windows 95/98/ME, Windows NT/2000/XP, OS/2, Macintosh, etc Environmental LM6000 Operating Temperature: 0 to 50 C LS6000 Operating Temperature: 0 to 40 C Relative Humidity: 10 to 95%, non-condensing Storage Temperature: -20 to 60 C Vibration: 5-17Hz, 0.1" double amplitude displacement; Hz, 1.5G acceleration peak to peak Shock: 10G acceleration peak to peak 12

15 Chapter 2: Monitor Installation Nematron Analog Monitors are very easy to install. As you set up your system, please refer to the following procedures. 2.1 Cable Connections LCD without Touch Screen If you want to install LCD without Touch Screen, just connect the VGA cable from LCD connector to the system VGA Signal Input port. The power connection you can choose to use the 12VDC jack (with a 12VDC power adaptor that ship with each unit) or the terminal block. In the terminal block connector, 12V or 24C DC inputs are available. 13

16 2.1.2 LCD with Touch Screen If you want to install LCD with Touch Screen, please connect RS-232 connector from LCD to your COM port on the PC. The driver for the touchscreen is provided on the CD, which ships with the Monitor. 14

17 2.2 Panel Mounting Nematron Analog Monitors are suitable for panel mounting. As you mount this flat panel display, please refer to the diagram below. Care should be taken in applying torque to the clips. An alternating pattern of tightening the clips should be used so that even compression of the perimeter gasket is achieved. Only about 50% compression is required on that gasket to achieve a NEMA 4 seal. Take care not to apply too much torque as damage can be caused to the front panel. Product Cutout Width Cutout Height LM/LS mm mm LM/LS mm mm LM/LS mm mm 15

18 2.3 Arm Mounting Nematron Analog Monitors are suitable for 75/100mm interface pads or for arm mounting and can be provided with an optional Arm Mounting Kit. Arm mounting and the specification conform to the proposed VESA standard. 16

19 2.4 Wall Mounting Nematron Analog Monitors are suitable for wall mounting. The components required for this mounting method are provided with each unit. Step 1: Measure and mark placement of brackets based on display size. Step 2: Drill and fasten wall-mount brackets. Step 3: Mount monitor on wall-mount brackets. Step 4: Install wall-mount vibration kit bracket. 17

20 2.4.1 LM9000 / LS9000 (17-inch) Wallmount LM8000 / LS8000 (15-inch) Wallmount 18

21 2.4.3 LM6000 / LS6000 (12.1-inch) Wallmount 19

22 2.5 Rack Mounting Nematron Analog Monitors can be provided with an optional monitor size specific rackmount kit suitable for a 19 Industrial Rack. The following diagram shows how to mount Nematron Analog Monitors onto the 19" Rack LM9000 / LS9000 (17-inch) Rackmount LM8000 / LS8000 (15-inch) Rackmount 20

23 2.5.3 LM6000 / LS6000 (12.1-inch) Rackmount 21

24 Chapter 3: User Mode OSD Information 3.1 LM9000 / LS9000 and LM8000 / LS8000 LEFT Button UP/AUTO Button RIGHT Button DOWN Button RETURN/MENU Button LCD ON/OFF Button POWER LED Indicator Features VGA Input: RGB VGA input Maximum pixel rate: 24bit pixel at 100MHz 48bit pixel at 135MHz LM/LS9000 Flat Panel resolution up to 1280 x 1024 LM/LS8000 Flat Panel resolution up to 1024 x 768 Color TFT LCD Panel support 48bit 2-pixel/clock data interface 24bit 1-pixel/clock data interface Flat Panel function support: Amplitude modulation for color TFT LCD panel Panel horizontal/vertical expansion Panel horizontal/vertical scale up and down LCD panel display enhancement: Filter & interpolation 10bit Gamma correction table. 16-stage of DDC data read/write buffer VESA DPMS: Automatic flat panel power sequencing Delayed power-on control for flat panel protection AD converter: Trumpion ZURACIII t

25 3.1.2 Button Functions There are six buttons on the OSD panel: ON/OFF, Auto (Up) Down, Right, Left, and Menu (Return). The functions of these six buttons are as follows: Menu (Return) Button Press to open or close the OSD window and to enter user mode so that function adjustments or item selections can be made. There may be many levels in one item. As you select this kind of item, you will enter the next level and see the sub-items. Right Button Press to Scroll item right or down to decrease the value or to switch the selected item to another. Left Button Press to Scroll item left or up to increase the value or to switch the selected item to another. Auto (Up) Button Press to Auto adjust the LCD. ON/OFF Button Press to Control power ON/OFF. Down Button Reserved. Green LED Power ON and Active. Orange LED Power ON and Sleep. LED No Display Power OFF. 23

26 3.1.3 User Mode OSD Structure LEVEL 0 LEVEL 1 VALUE DISPLAY ADJUST H-Position V-Position 0-30 CLOCK PHASE 0-31 AUTO EXIT YES, NO Press Menu Button INPUT SELECT ANALOG Press Menu Button DIGITAL VIDEO COMPOSITE VIDEO S-VIDEO EXIT Press Menu Button Press Menu Button Press Menu Button Press Menu Button COLOR ADJUST COLOR TEMPERATURE 6500K, 9300K RED GAIN GREEN GAIN BLUE GAIN EXIT Press Menu Button OSD ADJUST H-Position V-Position OSD-OFF TIME LANGUAGE EXIT English, French, German, Italian, Spanish Press Menu Button ZURAC ADJUST BRIGHTNESS-Z CONTRAST-Z DOS-MODE TEXT, GRAPHICS CONTRAST-ADC EXIT Press Menu Button EXIT EXIT OSD Press Menu Button 24

27 3.1.4 User Mode OSD Item Description AUTO (Auto-Adjustment) This item will automatically adjust the H/V position, frequency, phase, and black level. PHASE This item will adjust the sampling phase. BRIGHTNESS-Z Used to adjust the brightness of screen. This function will adjust the offset value of ZURAC. Setting this value too high or too low will destroy the quality of image. CONTRAST-Z CONTRAST-ADC Used to adjust the contrast of screen. These functions will adjust the gain value of ZURAC or ADC. Adjusting this value too high or too low will destroy the quality of image. DOS-MODE Used to choose VGA input signal that is text mode or graphic mode. (It is only selectable on resolution of 720/640x400 or 720/640x350.) 400 and 350 standard IBM modes have the same H- sync. and V-sync. Value. AV-0911 MPU cannot differentiate them automatically. Users need to adjust them manually to match proper VGA mode. H-POSITION Used to adjust horizontal display position of image. V-POSITION Used to adjust vertical display position of image. LANGUAGE Used to select one of the languages using on OSD display. English is the default language. English Spanish German French Italian EXIT Press the EXIT key to exit the OSD menu when the OSD menu is on top. 25

28 3.2 LM6000 / LS6000 LCD ON/OFF Button EXIT Button UP Button DOWN Button MENU Button POWER LED Indicator Features Input signal: VGA input Maximum pixel rate: 100MHz Flat Panel resolution up to 800 x 600 Color TFT LCD Panel support 6/24-bit 2-pixel/clock data interface 24/18-bit 1-pixel/clock data interface Flat Panel function support: Amplitude modulation for color TFT LCD panel Panel horizontal/vertical expansion Panel horizontal/vertical scale down LCD panel display enhancement: Filter & interpolation Gamma correction (64x6-bit by 3 gamma RAM) VESA DDC interface: DDC1 (unidirectional) and DDC2B (bi-directional, I2C interface) DDC2B+ data-write function DDC error recovery control 16-stage of DDC data read/write buffer VESA DPMS: Automatic flat panel power sequencing Delayed power-on control for flat panel protection AD converter: Genesis gmzan1 26

29 3.2.2 Button Functions There are five buttons on OSD panel: Menu, Down, Up, Exit and LCD ON/OFF. The functions of these buttons are as follows: Menu Button Press to open or close the OSD window and to enter user mode so that the function adjustments or item selections can be made. There may be many levels in one item. As you select the kind of item, you will enter the next level and see the sub-items. Down Button Press to Scroll item down or to decrease the value, or to toggle the selected item value (YES/NO). Up Button Press to Scroll item up to increase the value, or to toggle the selected item value (YES / NO). Exit Button There are many Levels in the OSD window. As you select the Exit button, you will back to main menu (level 0). When the small OSD is open, pressing this button will turn off the small OSD. LCD ON/OFF Button Turns the monitor ON or OFF User Mode OSD Structure Level 0 Level 1 Value RGB Menu Brightness Press MENU Button Red -127 ~ 127 Green -127 ~ 127 Blue -127 ~ 127 Color Temp 0 ~ 7 Sharpness 0, 1 Main Menu Press MENU Button Geometry Menu Auto-Adjustment Press MENU Button H. Position 0 ~ 252 V. Position 1 ~ 26 H. Total 1004 ~ 1108 Auto Phase Press MENU Button Delay 0 ~ 61 Main Menu Press MENU Button 27

30 Contrast Menu Auto-Balance Press MENU Button Contrast Press MENU Button Red 0 ~ 511 Green 0 ~ 511 Blue 0 ~ 511 Balance Press MENU Button Red 0 ~ 127 Green 0 ~ 127 Blue 0 ~ 127 Main Menu Press MENU Button Language Menu English Press MENU Button Spanish Press MENU Button Main Menu Auto Training DOS/GFX NVRAM init Power Down Revert Save ON/OFF ON/OFF Press MENU Button Press MENU Button Press MENU Button Press MENU Button 28

31 3.2.4 User Mode OSD Item Description Auto-Adjustment This item will automatically adjust the H/V position, frequency, phase, and black level. Auto Phase This item will automatically adjust the sampling Phase. Brightness Used to adjust the brightness of screen. This function will adjust the offset value of ADC. Setting this value too high or too low will destroy the quality of image. Contrast Used to adjust the contrast of screen, this function will adjust the gain value of ADC. Setting this value too high or too low will destroy the quality of image. DOS/GFX Used to choose VGA input signals that are text mode or graphic mode. (It is only selectable on resolution of 720/640x400 or 720/640x350.) 400 and 350 standard IBM mode have the same Hsync. and Vsync. value, AV-9261 MPU can not differentiate them automatically, therefore the user needs to adjust them manually to match proper VGA mode. 29

32 H. Position Used to adjust horizontal display position of image. V. Position Used to adjust vertical display position of image. Language It is used to select the languages used on the OSD display. AV-9261 now can support 2 languages on OSD display. English is the default language. Spanish is optional. Revert Used to reload original parameters from the factory OSD data area of the system EEPROM 24c16 device to re-initialize AV-9261 system device. When user adjusts OSD data too much and cannot see improved display quality, the user can select this item and MPU will reload default BIOS setting and re-initialize the system. Save Used to save the parameters into the user OSD adjustment data area of the system EEPROM 24c16 device and close OSD. Whenever user adjusts any parameters, it is necessary to execute this item to save data into EEPROM. Next time power is turned on, the MPU will use the stored data to initialize the AV-9261 system. 30

33 Main Menu Every level of OSD has the item Main Menu. This item lets the user leave the current level and jump to an upper level, or the user may press the Exit key. Exit Press the EXIT key to exit the OSD menu when the OSD menu is on top of this level. 31

34 Nematron Corporation 5840 Interface Drive Ann Arbor, Michigan CE Mark Declaration Of Conformity Nematron Corporation hereby acknowledges that compliance testing in accordance with applicable standards of the EU s EMC Directive, 89/336/EEC, and the Low Voltage Directive, 73/23/EEC, were successfully completed on a sample of the equipment identified below: Equipment Class: Product Model Series: Year Of Manufacturer: 2003 Information Technology Equipment LM8000, LM9000, LS8000 Series Monitors This Product Complies With: EN55022: 1998 Class A Emissions EN55024: 1998 EMC Immunity We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Manufacturer: Nematron Corporation Signature: Position: CEO Full Name: Matthew S. Galvez Place: Nematron Corporation Date: December 11, 2003 DOC-IWS-654B