NEUROLOGIC RESEARCH CORPORATION MODEL 2150

Transcription

1 NEUROLOGIC RESEARCH CORPORATION FOUR DIGITAL INPUT / FOUR DIGITAL OUTPUT NETWORK NODE - Very compact design available in DIN Rail and NEMA 4X enclosures. - LonWorks FTT-10A network interface with all inputs and outputs communicated via Standard Network Variable Types (SNVT) - Switching power supply allows operation from a wide range of low voltage AC or DC. - Four isolated outputs via Form C relays with transient voltage clamps and LED status indicators. - Four isolated inputs capable of handling 3-36VDC or /60 Hz. Inputs have transient voltage protection and LED status indicators. - Removable terminal blocks on all connections. - Two non-dedicated Temperature Alarm Blocks. - Two non-dedicated Percent Alarm Blocks. - Inputs have user configurable debounce. - Outputs are controlled via a flexible output block that is capable of user specified Boolean logic functions on multiple Input Network Variables. - Outputs have configurable minimum on and off time to prevent equipment damage and tailor output waveform. - Outputs types of pulse, toggle, cycle, and flash are supported. DESCRIPTION The Model 2150 is a LonWorks based product that has four isolated relay outputs and four isolated inputs. All inputs and outputs are communicated via Standard Network Variable Types (SNVT). The outputs are four Form C relays. Form C relays are single pole double throw with Normally Closed and Normally Open output contacts. Four red LEDs indicate the status of the output relays. The four isolated inputs are capable of detecting a wide range of low voltage AC or DC input. The inputs can be used with voltage output, dry contact, sinking (NPN), and sourcing (PNP) type devices. All inputs and outputs have transient voltage suppression. Four green LEDs indicate the presence of an input signal. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 1

2 Additionally, the Model 2150 includes a flexible firmware layer that includes two Temperature Alarm Blocks, two Percent Alarm Blocks, four Hardware Input Blocks and four Hardware Output Blocks. The Firmware Blocks can be used individually or tied together to accomplish more complex logic. For example, a relay output can be tied to the Temperature Alarm Block to turn on a warning light if a temperature set point is exceeded. For efficient use of input power, the Model 2150 uses a switching power supply. It can operate from a wide range of low voltage DC or AC. DIN Rail Enclosure The DIN Rail Enclosure allows mounting on a standard 35 mm DIN Rail. Please see the diagram below. Note, you must remove the top cover with a small screwdriver to access the Service Switch and view the input and output Status LEDs. TB1: Power and Net TB3: Inputs Service Switch 4 Input Status LEDs 4 Output Status LEDS (Remove top cover with a small TB2: Relay Outputs NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 2

3 NEMA 4X Enclosure A diagram and layout of the NEMA 4X Enclosure option is shown below. The enclosure can be wall or panel mounted and is appropriate for outdoor environments. To do so, remove the cover. See picture below. Use a #6 screw and drop into mounting holes shown below. Note, mounting holes do not violate the enclosure seal. Please do not drill holes into the bottom of the enclosure. This voids the NEMA 4X rating. Wall / Panel Mounting Holes. Use #6 screws TB2: Relay Outputs TB1: Power and Net TB3: Inputs 4 Red Output Status LEDs Service Switch and LED 4 Green Input Status LEDs The sides of the enclosure have knockouts of different diameters. Please see the diagram below. The enclosure is shipped with all knockouts intact. This allows the customer to use the one most appropriate for the installation. Please note the 20 mm knockout should work well with ½ NPT conduit hubs as well as cable glands. The larger knockouts of 32/20 mm are located at top and bottom sides in the orientation shown above. For best results, conduit entries should be attached to the bottom side. This prevents condensation in the conduit from draining into the enclosure. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 3

4 Larger Knockouts (2 sides) Outer 32 mm Inner 20 mm (Use with most ½ NPT fittings) Place flat screwdriver at the desired diameter and tap with a hammer. Smaller Knockouts (2 sides) Outer 25 mm Inner 16 mm Input Power and Network Interface The Model 2150 has an efficient switching power supply that operates from 10 to 36 Volts DC or 12 to 24 Volts AC. It typically draws less than 1.5 watts. Input power is reverse voltage protected and fused. Fuses do not need to be replaced. The network interface is Echelon s FTT-10 Free Topology Transceiver. The interface includes DC blocking capacitors for compatibility with Link Power Transceivers. The network connection is not sensitive to polarity. Please note, the Model 2150 does not include any network termination and it must be added externally. Power and network are connected via terminal block TB1 or TB2. The two connectors are identical to allow for daisy chaining. TERMINAL BLOCK TB1 FUNCTION Power and Network Connection. 1: NetA 2: NetB 3: VinA = Polarity insensitive power supply connection: VDC or VAC 4: VinB = Polarity insensitive power supply connection: VDC or VAC NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 4

5 Hardware Outputs Hardware outputs in the Model 2150 are accomplished by four Form C relays, which provide Normally Open and Normally Closed contact outputs. A simplified diagram of a single output is shown below TERMINA L BLOCK FUNCTION TB2 Relay Outputs Connector 1: Relay Output Common #1 2: Normally Open Relay Output #1 3: Normally Closed Relay Output #1 4: Relay Output Common #2 5: Normally Open Relay Output #2 6: Normally Closed Relay Output #2 7: Relay Output Common #3 8: Normally Open Relay Output #3 9: Normally Closed Relay Output #3 10: Relay Output Common #4 11: Normally Open Relay Output #4 12: Normally Closed Relay Output #4 TB2 COM NO NC Model 2150 WARNING Externally fuse the Relay Outputs using a 2 Amp rated fuse. Please wire any high voltage AC input before applying electrical power. Failure to do so may result in electrical shock. Hardware Inputs All hardware inputs are accessed via Terminal Block TB3. The four hardware inputs essentially sense a voltage input. They are isolated from each other and will detect a wide range of low voltage AC or DC inputs. They can be used with many types of inputs including dry contact, Sinking, and Sourcing types. Please see the following diagrams for wiring configurations. TERMINAL BLOCK TB3 FUNCTION Digital Inputs Connector 1: Input #1 (+) DC Positive, polarity insensitive for AC input 2: Input #1 (-) DC Negative, polarity insensitive for AC input 3: Input #2 (+) DC Positive, polarity insensitive for AC input 4: Input #2 (-) DC Negative, polarity insensitive for AC input 5: Input #3 (+) DC Positive, polarity insensitive for AC input 6: Input #3 (-) DC Negative, polarity insensitive for AC input 7: Input #4 (+) DC Positive, polarity insensitive for AC input 8: Input #4 (-) DC Negative, polarity insensitive for AC input NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 5

6 Input Connection Diagrams 3-24 VAC / 3-36 VDC Power Supply VOUT + Model VDC Power Supply VOUT + Model 2150 VOUT - VOUT - IN+ TB3 IN+ TB3 IN- IN- Dry Contact NPN Sensor Output 3-24 VAC / 3-36 VDC Voltage 2mA VOUT + Model 2150 VOUT VDC Power Supply VOUT + Model 2150 VOUT - IN+ IN- TB3 PNP Sensor Output IN+ IN- TB3 NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 6

7 FIRMWARE The Model 2150 implements its firmware using multiple Logic Blocks. Each Block performs a specific function. Blocks are configured, controlled and provide output via network variables. They can be tied together or cascaded by binding of outputs and input network variables. Connecting Blocks together allows more complex functions to be performed. Connected Blocks can reside on the same physical device or separate devices attached via a LonWorks network. Temperature and Percent Alarm Blocks nvitemp ncitempsp ncitempdb ncitempsendt Temperature Alarm Block nvotempalm nvipcnt ncipcntsp ncipcntdb ncipcntsendt Percent Alarm Block nvopcntalm The Model 2150 contains two Temperature and two Percent Alarm Blocks. Block diagrams are shown above. Each alarm block has a real-time value, a setpoint, and a deadband. Real-time value for Temperature Alarm Blocks is via nvitemp. Real-time value for Percent Alarm Blocks is via nvipcnt. Setpoint and deadband inputs are saved in non-volatile memory. The deadband is used to prevent intermittent alarms when close to the setpoint. Each block has an output indicating the status of the alarm condition. Please see the Network Interface section for a detailed description of the network variable types. Configuring Alarm Block for High or Low Alarm Output To configure the Block output as a high alarm, the deadband must larger or equal to zero. For low alarms configure the deadband as a negative value. In both cases, the absolute value of the deadband is used. How Alarms are Evaluated? A high alarm is defined as follows: If Value > Setpoint Alarm Output = ST_ON If Value <= (Setpoint Deadband) Alarm Output = ST_OFF A low alarm is defined as follows. Note, the deadband network variable is defined as a negative to tell the firmware that this is a low alarm. The absolute value is used in the logic below. If Value < Setpoint Alarm Output = ST_ON NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 7

8 If Value >= (Setpoint + Deadband) Alarm Output = ST_OFF Overriding an Alarm Block and Reset Condition If real-time value, setpoint, or deadband of an Alarm Block contains a value of 32767, the alarm output will be forced to an ST_NUL. The output of the Alarm Blocks has a type of SNVT_lev_disc. ST_NUL is a special value, equal to 255, which indicates data is undefined. Many sensors will force their temperature or percentage output value to to indicate an error condition. Factory defaults for the setpoint and deadband are forced to Each time the Model 2150 is turned on, it initializes its real-time input for each Alarm Block to This insures the firmware logic is always operating on valid data. For an Alarm Block to operate, the user must enter a valid setpoint and deadband upon receiving it from the factory. Additionally, the firmware must receive a network variable update on its real-time input for the output to be valid. Network Variable Update Control for Alarm Blocks The configuration network variable ncitempsendt and ncipcntsendt control updates to nvotempalm and nvopcntalm output network variables respectively. These are the minimum time between updates even if changes occur. The ncimaxsendt network variable controls the maximum updates of all output network variables. Hardware Input Blocks Physical Hardware Input ncihwindebouncet Hardware Input Block nvohwin The Model 2150 contains four Hardware Input Blocks. A diagram is shown above. The block receives its input from the physical hardware. A configurable debounce time can be set via the ncihwindebouncet network variable. The output of the block is available using nvohwin Output Network Variable. Please note that ncihwindebouncet also controls updates to nvohwin output network variables. It is the minimum time between updates even if changes occur. The ncimaxsendt network variable controls the maximum updates of all output network variables. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 8

9 Hardware Output Blocks ncihwoutsendt Hardware Output Block nviina nviinb Invert Stage Ignore Stage Boolean Logic Stage Invert Logic Stage Logic Output Output Stage nvohwout nviinc (I) (D) (L) (V) (O) Physical Relay Output ncihwoutdebt ncihwoutont ncihwoutofft The Model 2150 firmware contains four Hardware Output Blocks. The output of each block controls the corresponding physical relay output. The Blocks are highly configurable but simple to use. Hardware Output Blocks have the following features: - Controlled by up to three input network variables: nviina, nviinb, and nviinc. - Each input can be individually inverted. - Each input can be individually ignored. - A Boolean logic of AND / OR / Exclusive OR can be performed on the inputs - The Boolean logic output can be inverted - The output can be configured to follow the Logic Output, toggle, pulse, flash or cycle. - Configurable on and off times can be specified to prevent equipment damage and specify output characteristics. - The output of the block controls the physical output relay and written to a network variable for propagation to other devices or cascading to other Blocks. - All inputs are simultaneously debounced before any logic is performed. - The output can be overridden allowing quick shutdown in case of error conditions. Form C Relay Outputs The Model 2150 has Form C relay outputs. Normally Open and Normally Closed contacts are available. The OFF condition implies that the Normally Open contact is open. The ON condition implies that the Normally Open contact is closed. The Normally Closed contact will be the opposite. Debouncing Inputs Input debouncing can be specified using the ncihwoutdebt network variable. All inputs that are not ignored are debounced simultaneously. That is, a change on any of the inputs will restart the debounce timer. This insures inputs are stable before any logic is performed. Configuration of Hardware Output Blocks using ncihwoutconfig All four Hardware Output Blocks are configured via the ncihwoutconfig network variable. It is an ASCII string of 27 characters in the following format: NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 9

10 IDLVOX,IDLVOX,IDLVOX,IDLVOX Please note that each Block is configured via a series of 6 ASCII characters identified as: IDLVOX. A comma separates the sets for each of the four Blocks. Commas do not have spaces before or after them. The left-most set configures the first Block. The right-most set configures the fourth Block and so on. The characters above are only for identification of each position in the configuration string and are not what is actually specified. Please see the diagram above. For example the first character identified by I configures the Invert Stage of the Block. The character identified by D configures the Ignore Stage of the Block and so on. The length and format of the string is very important. It must be 27 characters long and have commas in the positions shown. If invalid values are entered, it will cause that block to go into over-ride, turn the output relay off, and set the network variable output to ST_NUL. Each configuration character is defined below. All values are in ASCII. Low and upper case are allowed. Configuration Character ID I D L V O Usage Configures input inversion stage Configures ignore / don t care stage Configures Boolean logic stage Configures inversion of logic stage Configures output type Description 0 = No inputs are inverted (Factory Default) 1 = Input A is inverted 2 = Input B is inverted 3 = Inputs A and B are inverted 4 = Input C is inverted 5 = Inputs A and C are inverted 6 = Inputs B and C are inverted 7 = Inputs A, B, and C are inverted 0 = No inputs are ignored 1 = Input A is ignored 2 = Input B is ignored 3 = Inputs A and B are ignored 4 = Input C is ignored 5 = Inputs A and C are ignored 6 = Inputs B and C are ignored (Factory Default) 7 = Inputs A, B, and C are ignored O = Boolean OR (Factory Default) A = Boolean AND X = Boolean Exclusive OR N = Normal, do not invert (Factory Default) L = Invert logic output N = Normal: Output follows logic output (Factory Default). The ncihwoutont and ncihwoutofft are used to define the minimum on and off times even if the Logic Output changes. Prevents equipment cycling. T = Toggle: Output toggles every time Logic Output goes from off to on. C = Cycle: Output cycles on/off, square wave, as long as Logic Output is on. On time is defined by ncihwoutont. Off time is defined by ncihwoutofft F = Flash: Variation on Cycle Type. Please see text for full description. P = Pulse: Output will produce an output pulse equal to ncihwoutont when Logic Output goes from off to on. X Future usage Not used, but must be left as a place holder. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 10

11 Flash Output Type A Flash output type can be specified for the output. This type is explained in detail here. The Flash output type works as follows and essentially allows the first input, nviina to turn the output on, off, or flash at different rates. LogicOut nviina Hardware Output On ST_OFF Off On ST_ON On On ST_HIGH Output cycles on/off: On for ncihwoutont, Off for ncihwoutofft On ST_MED Output cycles on/off: On for 2 X ncihwoutont, Off for 2 X ncihwoutofft On ST_LOW Output cycles on/off: On for 4 X ncihwoutont, Off for 4 X ncihwoutofft Off Don t care Off Overriding the Block Output and Reset Condition Upon reset, the Model 2150 initializes all inputs to the Block to ST_NUL. A value of ST_NUL on any of the input that is not being ignored will force the physical hardware output off and the output network variable to ST_NUL. This accomplishes two tasks. One, it forces the block to wait for data on all inputs that are not ignored before performing any logic. Two, it allows any input, that is not being ignored, to over-ride any output being performed by the Block and turn off the physical output. Default Factory Configuration The factory default value loaded into the ncihwoutconfig string is shown below: 06ONNX,06ONNX,06ONNX,06ONNX The above configuration simply configures each hardware output to be controlled via the nviina network variable. Note, nviinb and nviinc are ignored and must be enabled if they are to be used. The OR logic function on a single input, nviina, allows the output to follow the state of nviina. Please note, the hardware output will observe the minimum on and off periods set by ncihwoutont and ncihwoutofft configuration variables. Network Variable Update Control for Hardware Output Blocks The configuration network variable ncihwoutsendt control updates to nvohwout output network variables. It is the minimum time between updates even if changes occur. The ncimaxsendt network variable controls the maximum updates of all output network variables. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 11

12 NETWORK INTERFACE CONFIGURATION NETWORK VARIABLES Network Variable Format Description Temperature Alarm Block ncitempsp[2] SNVT_temp_p Setpoint input. Default is ncitempdb[2] SNVT_temp_p Deadband input. Default is ncitempsendt[2] SNVT_time_sec Minimum time between nvotempalm updates even if changes occur. This is sometimes called throttle. Percent Alarm Block ncipcntsp[2] SNVT_lev_percent Setpoint input. Default is ncipcntdb[2] SNVT_lev_percent Deadband input. Default is ncipcntsendt[2] SNVT_time_sec Minimum time between nvopcntalm updates even if changes occur. This is sometimes called throttle. Hardware Input Block ncihwindebouncet[4] SNVT_time_sec Debounce time for each of the Hardware Input Blocks. This parameter is also the minimum time between nvohwin updates even if changes occur. This is also called throttle. Hardware Output Block ncihwoutconfig SNVT_str_asc ASCII configuration string used to control function of all Hardware Output Blocks. Please see Hardware Output Blocks Section for complete specification. ncihwoutdebt[4] SNVT_time_sec Debounce time for all inputs to Hardware Output Blocks. ncihwoutont[4] SNVT_time_sec On time for output stage ncihwoutofft[4] SNVT_time_sec Off time for output stage ncihwoutsendt[4] All Blocks ncimaxsendt SNVT_time_sec SNVT_time_sec INPUT NETWORK VARIABLES Minimum time between nvohwout updates even if changes occur. This is sometimes called throttle. Maximum time between network variable updates even if no changes occur. This is sometimes called heartbeat. A 0 disables the heartbeat. Network Variable Format Description Temperature Alarm Block nvitemp[2] SNVT_temp_p Real-time temperature data. Percent Alarm Block nvipcnt[2] SNVT_lev_percent Real-time percent data. Hardware Input Block None Hardware Output Block nviina[4] nviinb[4] nviinc[4] SNVT_lev_disc SNVT_lev_disc SNVT_lev_disc Hardware Input Block get their input from the physical inputs on the Model First input of Hardware Out Block. Initialized to ST_NUL on power-up. Second input of Hardware Out Block. Initialized to ST_NUL on power-up. Third input of Hardware Out Block. Initialized to ST_NUL on power-up. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 12

13 OUTPUT NETWORK VARIABLES Network Variable Format Description Temperature Alarm Block nvotempalm[2] SNVT_lev_disc Output of Temperature Alarm Blocks. Percent Alarm Block nvopcntalm[2] SNVT_lev_disc Output of Percent Alarm Blocks. Hardware Input Block nohwin[4] SNVT_lev_disc Output of Hardware Input Blocks. Hardware Output Block nohwout[4] SNVT_lev_disc Output of Hardware Output Blocks. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 13

14 SPECIFICATION General CPU Operating Temperature Operating Humidity Input Power Input Power Protection Current Consumption Network Transceiver Type Input Power and Network Wiring 10 MHz o C 0-95% Relative Humidity non-condensing VDC or VAC Input power is fused and transient voltage protected. (Fuses do not need to be replaced) 1.5 watts typical with all inputs and outputs on. Echelon FTT-10A transceiver at 78 kbps. DC blocking capacitors for LPT10 network. Removable terminal blocks. Input power and network wiring are polarity insensitive. Isolated Hardware Inputs Type Individually isolated voltage input. DC Voltage Input Range 3-36 Volts. Input must be able to supply 2 ma maximum. AC Voltage Input Range 3-24 Volts. Input must be able to supply 2 ma maximum. Protection Reverse voltage protection and transient voltage suppressors Isolation 500 Volts minimum. Relay Outputs Type Contact Rating Isolation Protection Form C relay with normally open and normally closed outputs 30 2 A or 125 2A Resistive load. 500 Volts RMS minimum. Transient voltage suppression. Must be externally fused via 2A fuse. Dimension and Materials DIN Rail Enclosure s external Dimension DIN Rail Enclosure s Material NEMA 4 Enclosure s external Dimension NEMA 4 Enclosure s Material ORDERING INFORMATION 71 mm (2.8 ) W x 90 mm (3.54 ) L x 58 mm (2.28 ) H Grey frame retardant Noryl UL mm (5.12 ) W x 130 mm (5.12 ) L x 60 mm (2.36 ) H Grey polycarbonate with translucent polycarbonate cover. Flame retardant UL Model 2150 Four Digital Output / Four Digital Input Network Node Code Enclosure / Housing Options -0 NEMA 4X -1 DIN-Rail Mount Code Network Communications Option -0 TP/FTT-10A - LonWorks Model 2150 with LonWorks FTT-10A transceiver in DIN-Rail housing Echelon, LON, LONWORKS, Neuron, 3120, 3150, and LONMARK are trademarks of Echelon Corporation. NEUROLOGIC RESEARCH CORPORATION Copyright (c) 2003,2004 Rev. 1 Page 14