ft Aspen Fir Item # Commercial ITEM Lights
|
|
- Ashlyn Phelps
- 5 years ago
- Views:
Transcription
1 ft Aspen Fir Item # Commercial ITEM Lights PARTS LIST A. BOTTOM B. LOWER MIDDLE C. UPPER MIDDLE D. TOP E. TREE STAND NUMBER OF PERSONS RECOMMENDED FOR ASSEMBLY: 2 SKU ASPEN FIR TREE 3243 TIPS STANDARD STAND 1200 Comerial LIGHTS MAX DIAMETER 60 HARDWARE A. SURGE PROTECTOR QUANTITY 1 PC B. REMOTE CONTROL W/ RECEIVER QUANTITY 1 SET C. EXTRA BULBS AND FUSES QUANTITY EACH 18 PCS D. REPLACEMENT LIGHT STRANDS QUANTITY 2 PC 1. Unpack: Carefully remove the contents from the carton and keep the carton for future storage. Some sections of the tree may be heavy and assistance may be required. Remove any outer foam wrapping from the tree and its branches (See Fig. 1A). Fig. 1A 1 P age
2 CAUTION: Two people may be needed to balance and assemble tree s upper sections. Please use a ladder, if needed, and follow all ladder safety instructions. 2.1 Open the carton and take out all the contents. All contents that are listed in the Bill of Material section on this page should be enclosed. Locate the metal tree stand and assemble it by separating the legs of the stand to form an X shape (See Fig 2A). Insert each of the three screws into the holes on the stand s middle section, being sure that screws do not extend so far as to interfere with installation of the tree pole. Place tree stand in desired location. Fig 2A 2.2 Locate Tree Section A and remove the protective caps that are on the pole (they can be replaced when you repack your tree). Insert Tree Section A into the tree stand (See Fig. 2B). Make sure the pole is firmly inserted into the stand, and then turn all three screws until contact is made with the pole. If Section A is not sitting straight, then simply loosen the screws, adjust tree pole, and retighten the screws. All the branches are connected to the tree s center pole by metal hinges (See Figure 2). Remove the packing strap that is around the tree section and allow the branches to fall into place. 2.3 Locate Tree Section B and insert into the top of Tree Section A. Make sure section B is seated securely into the top of section A. Remove the packing strap that is wrapped around this tree section, same as you for Section A. Allow the branches and leaves to fall into place. 2.4 Locate Tree Section C and insert into the top of the Tree Section B. Make sure section C is seated securely into the top of section B. Remove the packing strap that is wrapped around this tree section, and allow the branches and leaves to fall into place. 2.5 Locate Tree Section D and insert into the top of the Tree Section C. Make sure section D is seated securely into the top of section C. Your tree is now complete (see Fig. 2E) Fig. 2E 2 P age
3 3. Light Set and Power Connection: 3.1 In the tree carton, there is a brown box that contains your On/Off Remote Kit(remote & remote receiver). Remove from box Plug your Remote Control Receiver Unit into the wall outlet located near tree The surge protector should plug into the remote control receiver Plug the extension cords from section(s) of tree into the surge protector. Please see diagram below. The Unit comes with one Remote Control. 3.5 Your tree is lighted with miniature lights that are strung on the tree at the factory. Those lights are plugged into the extension cords on the tree. Your 7.5 ft. tree will have ONE (1) extension cord plug that is in section A of your tree. This extension cord should plug directly into surge protector. Plug section D into section C using the open receptacle with tag stating plug in here Plug section C into section B using the open receptacle with tag stating plug in here Plug section B into section A using the open receptacle with tag stating plug in here Plug section A directly into surge protector. Connection of extension cords between sections. Starting at the top, Section D, look for the lead cord with 2 plugs stacked together. Drop this don into Section C and look forth red tag that says plug in here. Continue this for all sections. 3 P age
4 DISASSEMBLY OF YOUR TREE Unplug the extension cord plugs from the Remote Unit attached to the electrical outlet on the wall. Take off all of your ornaments and tree decorations before packing your tree back into its storage boxes. Starting from the top, gently lift off each section. Each section should be packed away in the carton that it came in. Each tree section should be turned upside down and then carefully press branches toward center pole for easier placement into the storage box. Carefully place the tree in its box and tape it shut. DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS 100ºF. 1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire. 2. Please use water only for cleaning purpose. 3. When not in use, store neatly in a cool, dry location protected from sun light. 4. When the remote control has malfunctioned, please remove the power strip from the receiver and plug the power strip directly into the wall. THE FOLLOWING STEPS WILL HELP MAKE YOUR TREE LOOK MORE REALISTIC 1. Light tree one section at a time as described in assembly instructions, so you can easily identify any bulbs that may be dislodged. Push any loose bulbs back into their sockets. 2. Separate the branch tips to form a V shape and fluff the needles. Make sure each tip is spread out and no two branches are touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial assembly instructions. You may want to wear cotton gloves when fluffing needles to avoid scratches and skin irritation. 3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly upward like they are growing towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide the center of the tree. 4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward. 5. Step back and review the tree. Adjust branches and tips as necessary to give the tree a fuller appearance (The tree may be shape differently (upswept /downswept /etc.) pending on one s preference.) 4 P age
5 TROUBLE SHOOTING 1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet. 2. If an entire section of the tree does not light, please review following actions: a. Check that all plugs within the tree are securely connected. b. Check fuse in power strip to determine TROUBLE if it may SHOOTING need replacement. TIPS Caution: (Cont.) Note that a blown fuse indicates an electrical overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet. Also unplug any additional strings or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse rating. If the replacement fuse blows, a short circuit may be present and the product should be discarded. c. Check fuse in plug connection on end of each light string.(see section on replacing plug fuses in this document). 3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.ant BASIC SAFETY INSTRUCTIONS When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be followed as stated below: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. 2. This seasonal use product is not intended for permanent installation or use. 3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat. 4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. 5. Do not let lamps rest on the supply cord or on any wire. 6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended. 7. This is an electrical product not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it. 8. Do not use this product for other than its intended use. 9. Do not hang ornaments or other objects from cord, wire or light string. 10. Do not close doors or windows on the product or extensions cords as this may damage the wire insulation. 11. Do not cover the product with cloth, paper or any material not part of the product when in use. 12. This product is equipped with push-in lamps. Do not twist the lamps. 13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded. 14. Read and follow all instructions that are on the product or provided with the product. CAUTION: To reduce the risk of fire and electric shock: a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and: b. Do not mount or support strings in a manner that can cut or damage wire insulation. 5 P age
6 USER INSTRUCTIONS TO REPLACE LIGHT BULBS CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE. 1. To reduce the risk of overheating, replace burned-out light bulbs promptly.use only 2.5 volt light bulbs only. 2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do not unplug by pulling on the cord. 3. Pull the light bulb and its attached plastic base straight out of light bulb holder. 4. Replace light bulb with only 2.5 volt super bright type light (provided with product). 5. If the new lamp base does not fit the replacement light bulb, follow the steps below before step 4. a. Remove the base of burned out light by straightening light leads and gently pull bulb out. b.thread metal leads of new lamp through hose in old base with one lead in each hold. c. After lamp is fully inserted into base, bend each lead up, like other lights in the light set so that the leads will touch the contacts inside the light socket. TO REPLACE A FUSE: CAUTION: FIRST UNPLUG YOUR PRODUCT FROMANY POWER SOURCE. 1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. FUSECOVER SLIDES FORWARD 2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards plug's metal prongs or blades. 3. Remove fuse carefully. 4. Risk of fire. Replace fuse ONLY with 3 Amp 120 Volt fuse. (Provided with product). 5. Close fuse cover. Return the sliding fuse cover back to its former closed position on attachment plug. 6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged Please contact one of our Product Specialists for assembly assistance or questions at or ps@frontgate.com. Specialists are available weekdays 8:00 a.m.to 8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m. 6 P age
7 7 P age
8 7.5 9 ft Aspen Fir Item # Commercial ITEM Lights PARTS LIST A. BOTTOM B. LOWER MIDDLE C. UPPER MIDDLE D. TOP E. TREE STAND NUMBER OF PERSONS RECOMMENDED FOR ASSEMBLY: 2 SKU ASPEN FIR TREE 4701 TIPS STANDARD STAND 1700 Commercial LIGHTS MAX DIAMETER 68 HARDWARE A. SURGE PROTECTOR QUANTITY 1 PC B. REMOTE CONTROL W/ RECEIVER QUANTITY 1 SET C. EXTRA BULBS AND FUSES QUANTITY EACH 68 PCS D. REPLACEMENT LIGHT STRANDS QUANTITY 2 PC 1. Unpack: Carefully remove the contents from the carton and keep the carton for future storage. Some sections of the tree may be heavy and assistance may be required. Remove any outer foam wrapping from the tree and its branches (See Fig. 1A). Fig. 1A 1 P age
9 CAUTION: Two people may be needed to balance and assemble tree s upper sections. Please use a ladder, if needed, and follow all ladder safety instructions. 2.1 Open the carton and take out all the contents. All contents that are listed in the Bill of Material section on this page should be enclosed. Locate the metal tree stand and assemble it by separating the legs of the stand to form an X shape (See Fig 2A). Insert each of the three screws into the holes on the stand s middle section, being sure that screws do not extend so far as to interfere with installation of the tree pole. Place tree stand in desired location. Fig 2A 2.2 Locate Tree Section A and remove the protective cap that is on the pole (cap can be replaced when you re-pack your tree). Insert Tree Section A into the tree stand (See Fig. 2B). Make sure the pole is firmly inserted into the stand, and then turn all three screws until contact is made with the pole. If Section A is not sitting straight, then simply loosen the screws, adjust tree pole, and retighten the screws. All the branches are connected to the tree s center pole by metal hinges (See Figure 2). Remove the packing strap that is around the tree section and allow the branches to fall into place. 2.3 Locate Tree Section B and insert into the top of Tree Section A. Make sure section B is seated securely into the top of section A. Remove the packing strap that is wrapped around this tree section, same as you did for Section A. Allow the branches and leaves to fall into place. 2.4 Locate Tree Section C and insert into the top of the Tree Section B. Make sure section C is seated securely into the top of section B. Remove the packing strap that is wrapped around this tree section, and allow the branches and leaves to fall into place. 2.5 Locate Tree Section D and insert into the top of the Tree Section C. Make sure section D is seated securely into the top of section C. Your tree is now complete (see Fig. 2E) Fig. 2E 2 P age
10 3. Light Set and Power Connection: 3.1 In the tree carton, there is a brown box that contains your On/Off Remote Kit (remote & remote receiver). Remove from box Plug your Remote Control Receiver Unit into the wall outlet located near tree The surge protector should plug into the remote control receiver Plug the extension cords from section(s) of tree into the surge protector. Please see diagram below. The Unit comes with one Remote Control. 3.5 Your tree is lighted with miniature lights that are strung on the tree at the factory. Those lights are plugged into the extension cords on the tree. Your 9 ft. tree will have only TWO (2) extension cords that will plug directly into the surge protector (1 from Section A, and 1 from Section B). This is also indicated by a red tag on these 2 plugs that says, Plug into electrical wall outlet or surge protector only. When you see that tag, plug that cord into the surge protector. Plug section D into section C using the open receptacle with tag stating plug in here Plug section C into section B using the open receptacle with tag stating plug in here Plug section B directly into surge protector Plug section A directly into surge protector. 3 P age
11 The plug connection process is diagramed above, but let s also walk through each step: Step#1. Starting at the top, Section D, find the lead cord with 2 plugs stacked together. Drop this down into the tree section below (Section C) and look for the red tag that says, plug in here. Plug into the open receptacle at that location. Step #2 - Section C, look for the end of extension cord (it has a red tag on it that says, Plug into section below into open receptacle. Drop this cord down into the tree section below (section B) and look for the red tag that says, plug in here. Plug into the open receptacle at that location. Step #3 Take the extension cord from Section B, drop it down the center of the tree in order to keep it better out of sight, and plug it directly into the surge protector. Step #4 Take the extension cord from the bottom section (Section A), and also plug it directly into the surge protector. Now your setup is complete and your tree should light up. If there are any sections that don t light up, please make sure all your sections are plugged in properly to their correct location. DISASSEMBLY OF YOUR TREE Unplug the extension cord plugs from the Remote Unit attached to the electrical outlet on the wall. Take off all of your ornaments and tree decorations before packing your tree back into its storage boxes. Starting from the top, gently lift off each section. Each section should be packed away in the carton that it came in. Each tree section should be turned upside down and then carefully press branches toward center pole for easier placement into the storage box. Carefully place the tree in its box and tape it shut. DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS 100ºF. 1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire. 2. Please use water only for cleaning purpose. 3. When not in use, store neatly in a cool, dry location protected from sun light. 4. When the remote control has malfunctioned, please remove the power strip from the receiver and plug the power strip directly into the wall. 4 P age
12 THE FOLLOWING STEPS WILL HELP MAKE YOUR TREE LOOK MORE REALISTIC 1. Light tree one section at a time as described in assembly instructions, so you can easily identify any bulbs that may be dislodged. Push any loose bulbs back into their sockets. 2. Separate the branch tips to form a V shape and fluff the needles. Make sure each tip is spread out and no two branches are touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial assembly instructions. You may want to wear cotton gloves when fluffing needles to avoid scratches and skin irritation. 3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly upward like they are growing towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide the center of the tree. 4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward. 5. Step back and review the tree. Adjust branches and tips as necessary to give the tree a fuller appearance (The tree may be shape differently (upswept /downswept /etc.) pending on one s preference.) 5 P age
13 TROUBLE SHOOTING 1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet. 2. If an entire section of the tree does not light, please review following actions: a. Check that all plugs within the tree TROUBLE are securely SHOOTING connected. TIPS (Cont.) b. Check fuse in power strip to determine if it may need replacement. Caution: Note that a blown fuse indicates an electrical overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet. Also unplug any additional strings or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse rating. If the replacement fuse blows, a short circuit may be present and the product should be discarded. c. Check fuse in plug connection on end of each light string.(see section on replacing plug fuses in this document). 3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.ant BASIC SAFETY INSTRUCTIONS When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be followed as stated below: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. 2. This seasonal use product is not intended for permanent installation or use. 3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat. 4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. 5. Do not let lamps rest on the supply cord or on any wire. 6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended. 7. This is an electrical product not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it. 8. Do not use this product for other than its intended use. 9. Do not hang ornaments or other objects from cord, wire or light string. 10. Do not close doors or windows on the product or extensions cords as this may damage the wire insulation. 11. Do not cover the product with cloth, paper or any material not part of the product when in use. 12. This product is equipped with push-in lamps. Do not twist the lamps. 13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded. 14. Read and follow all instructions that are on the product or provided with the product. CAUTION: To reduce the risk of fire and electric shock: a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and: b. Do not mount or support strings in a manner that can cut or damage wire insulation. 6 P age
14 USER INSTRUCTIONS TO REPLACE LIGHT BULBS CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE. 1. To reduce the risk of overheating, replace burned-out light bulbs promptly.use only 2.5 volt light bulbs only. 2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do not unplug by pulling on the cord. 3. Pull the light bulb and its attached plastic base straight out of light bulb holder. 4. Replace light bulb with only 2.5 volt super bright type light (provided with product). 5. If the new lamp base does not fit the replacement light bulb, follow the steps below before step 4. a. Remove the base of burned out light by straightening light leads and gently pull bulb out. b.thread metal leads of new lamp through hose in old base with one lead in each hold. c. After lamp is fully inserted into base, bend each lead up, like other lights in the light set so that the leads will touch the contacts inside the light socket. TO REPLACE A FUSE: CAUTION: FIRST UNPLUG YOUR PRODUCT FROMANY POWER SOURCE. 1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. FUSECOVER SLIDES FORWARD 2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards plug's metal prongs or blades. 3. Remove fuse carefully. 4. Risk of fire. Replace fuse ONLY with 3 Amp 120 Volt fuse. (Provided with product). 5. Close fuse cover. Return the sliding fuse cover back to its former closed position on attachment plug. 6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged Please contact one of our Product Specialists for assembly assistance or questions at or ps@frontgate.com. Specialists are available weekdays 8:00 a.m.to 8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m 7 P age
15 8 P age
16 7.510 ft Aspen Fir Item # Commercial ITEM Lights PARTS LIST A. BOTTOM B. LOWER MIDDLE C. MIDDLE D. UPPER MIDDLE E. TOP F. TREE STAND NUMBER OF PERSONS RECOMMENDED FOR ASSEMBLY: 2 SKU ASPEN FIR TREE 5775 TIPS STANDARD STAND 1900 Commercial LIGHTS MAX DIAMETER 70 HARDWARE A. SURGE PROTECTOR QUANTITY 1 PC B. REMOTE CONTROL W/ RECEIVER QUANTITY 1 SET C. EXTRA BULBS AND FUSES QUANTITY EACH 76 PCS D. REPLACEMENT LIGHT STRANDS QUANTITY 2 PC 1. Unpack: Carefully remove the contents from the carton and keep the carton for future storage. Some sections of the tree may be heavy and assistance may be required. Remove any outer foam wrapping from the tree and its branches (See Fig. 1A). Fig. 1A 1 P age
17 CAUTION: Two people may be needed to balance and assemble tree s upper sections. Please use a ladder, if needed, and follow all ladder safety instructions. 2.1 Open the carton and take out all the contents. All contents that are listed in the Bill of Material section on this page should be enclosed. Locate the metal tree stand and assemble it by separating the legs of the stand to form an X shape (See Fig 2A). Insert each of the three screws into the holes on the stand s middle section, being sure that screws do not extend so far as to interfere with installation of the tree pole. Place tree stand in desired location. Fig 2A 2.2 Locate Tree Section A and remove the protective cap that is on the pole (cap can be replaced when you re-pack your tree). Insert Tree Section A into the tree stand (See Fig. 2B). Make sure the pole is firmly inserted into the stand, and then turn all three screws until contact is made with the pole. If Section A is not sitting straight, then simply loosen the screws, adjust tree pole, and retighten the screws. All the branches are connected to the tree s center pole by metal hinges (See Figure 2). Remove the packing strap that is around the tree section and allow the branches to fall into place. 2.3 Locate Tree Section B and insert into the top of Tree Section A. Make sure section B is seated securely into the top of section A. Remove the packing strap that is wrapped around this tree section, same as you did for Section A. Allow the branches and leaves to fall into place. 2.4 Locate Tree Section C and insert into the top of the Tree Section B. Make sure section C is seated securely into the top of section B. Remove the packing strap that is wrapped around this tree section, and allow the branches and leaves to fall into place. 2.5 Locate Tree Section D and insert into the top of the Tree Section C. Make sure section D is seated securely into the top of section C. Your tree is now complete (see Fig. 2E) Fig. 2E 2 P age
18 3. Light Set and Power Connection: 3.1 In the tree carton, there is a brown box that contains your On/Off Remote Kit (remote & remote receiver). Remove from box Plug your Remote Control Receiver Unit into the wall outlet located near tree The surge protector should plug into the remote control receiver Plug the extension cords from section(s) of tree into the surge protector. Please see diagram below. The Unit comes with one Remote Control. 3.5 Your tree is lighted with miniature lights that are strung on the tree at the factory. Those lights are plugged into the extension cords on the tree. Your 10 ft. tree will have only TWO (2) extension cords that will plug directly into the surge protector (1 from Section A, and 1 from Section B). This is also indicated by a red tag on these 2 plugs that says, Plug into electrical wall outlet or surge protector only. When you see that tag, plug that cord into the surge protector. Plug section D into section C using the open receptacle with tag stating plug in here Plug section C into section B using the open receptacle with tag stating plug in here Plug section B directly into surge protector Plug section A directly into surge protector. 3 P age
19 The plug connection process is diagramed above, but let s also walk through each step: Step#1. Starting at the top, Section D, find the lead cord with 2 plugs stacked together. Drop this down into the tree section below (Section C) and look for the red tag that says, plug in here. Plug into the open receptacle at that location. Step #2 - Section C, look for the end of extension cord (it has a red tag on it that says, Plug into section below into open receptacle. Drop this cord down into the tree section below (section B) and look for the red tag that says, plug in here. Plug into the open receptacle at that location. Step #3 Take the extension cord from Section B, drop it down the center of the tree in order to keep it better out of sight, and plug it directly into the surge protector. Step #4 Take the extension cord from the bottom section (Section A), and also plug it directly into the surge protector. Now your setup is complete and your tree should light up. If there are any sections that don t light up, please make sure all your sections are plugged in properly to their correct location. DISASSEMBLY OF YOUR TREE Unplug the extension cord plugs from the Remote Unit attached to the electrical outlet on the wall. Take off all of your ornaments and tree decorations before packing your tree back into its storage boxes. Starting from the top, gently lift off each section. Each section should be packed away in the carton that it came in. Each tree section should be turned upside down and then carefully press branches toward center pole for easier placement into the storage box. Carefully place the tree in its box and tape it shut. DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS 100ºF. 1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire. 2. Please use water only for cleaning purpose. 3. When not in use, store neatly in a cool, dry location protected from sun light. 4. When the remote control has malfunctioned, please remove the power strip from the receiver and plug the power strip directly into the wall. 4 P age
20 THE FOLLOWING STEPS WILL HELP MAKE YOUR TREE LOOK MORE REALISTIC 1. Light tree one section at a time as described in assembly instructions, so you can easily identify any bulbs that may be dislodged. Push any loose bulbs back into their sockets. 2. Separate the branch tips to form a V shape and fluff the needles. Make sure each tip is spread out and no two branches are touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial assembly instructions. You may want to wear cotton gloves when fluffing needles to avoid scratches and skin irritation. 3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly upward like they are growing towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide the center of the tree. 4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward. 5. Step back and review the tree. Adjust branches and tips as necessary to give the tree a fuller appearance (The tree may be shape differently (upswept /downswept /etc.) pending on one s preference.) 5 P age
21 TROUBLE SHOOTING 1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet. 2. If an entire section of the tree does not light, please review following actions: a. Check that all plugs within the tree TROUBLE are securely SHOOTING connected. TIPS (Cont.) b. Check fuse in power strip to determine if it may need replacement. Caution: Note that a blown fuse indicates an electrical overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet. Also unplug any additional strings or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse rating. If the replacement fuse blows, a short circuit may be present and the product should be discarded. c. Check fuse in plug connection on end of each light string.(see section on replacing plug fuses in this document). 3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.ant BASIC SAFETY INSTRUCTIONS When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be followed as stated below: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. 2. This seasonal use product is not intended for permanent installation or use. 3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat. 4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. 5. Do not let lamps rest on the supply cord or on any wire. 6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended. 7. This is an electrical product not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it. 8. Do not use this product for other than its intended use. 9. Do not hang ornaments or other objects from cord, wire or light string. 10. Do not close doors or windows on the product or extensions cords as this may damage the wire insulation. 11. Do not cover the product with cloth, paper or any material not part of the product when in use. 12. This product is equipped with push-in lamps. Do not twist the lamps. 13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded. 14. Read and follow all instructions that are on the product or provided with the product. CAUTION: To reduce the risk of fire and electric shock: a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and: b. Do not mount or support strings in a manner that can cut or damage wire insulation. 6 P age
22 USER INSTRUCTIONS TO REPLACE LIGHT BULBS CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE. 1. To reduce the risk of overheating, replace burned-out light bulbs promptly.use only 2.5 volt light bulbs only. 2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do not unplug by pulling on the cord. 3. Pull the light bulb and its attached plastic base straight out of light bulb holder. 4. Replace light bulb with only 2.5 volt super bright type light (provided with product). 5. If the new lamp base does not fit the replacement light bulb, follow the steps below before step 4. a. Remove the base of burned out light by straightening light leads and gently pull bulb out. b.thread metal leads of new lamp through hose in old base with one lead in each hold. c. After lamp is fully inserted into base, bend each lead up, like other lights in the light set so that the leads will touch the contacts inside the light socket. TO REPLACE A FUSE: CAUTION: FIRST UNPLUG YOUR PRODUCT FROMANY POWER SOURCE. 1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. FUSECOVER SLIDES FORWARD 2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards plug's metal prongs or blades. 3. Remove fuse carefully. 4. Risk of fire. Replace fuse ONLY with 3 Amp 120 Volt fuse. (Provided with product). 5. Close fuse cover. Return the sliding fuse cover back to its former closed position on attachment plug. 6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged Please contact one of our Product Specialists for assembly assistance or questions at or ps@frontgate.com. Specialists are available weekdays 8:00 a.m.to 8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m 7 P age
Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443
Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. PARTS LIST: 2 Metal Plate Stands 5 Greenery
More informationThanks for shopping with Improvements! Rock Hill Pre-Light Command Christmas Tree- 7 Item #546329
Thanks for shopping with Improvements! Rock Hill Pre-Light Command Christmas Tree- 7 Item #546329 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. PARTS LIST: 1 Tree Stand (with 3 screws) 1 Tree
More information72In LED Lit Nutcracker Item # CAUTION: IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION: IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS FOR INDOOR and OUTDOOR USE The product and its adapter are intended for indoor and outdoor use. When product is used in outdoor
More informationCongratulations on your purchase!! 5-ft. KD Magnesium Animated Nutcracker with Remote Control Instructions
Congratulations on your purchase!! 5-ft. KD Magnesium Animated Nutcracker with Remote Control Instructions Frontgate Item no.: 141489 Safety Instructions: Please read and follow all instructions carefully
More informationThanks for shopping with Improvements! Personalized Holiday Laser Show Item #563474
Thanks for shopping with Improvements! Personalized Holiday Laser Show Item #563474 Note: When using this item, basic safety precautions should always be followed to reduce the risk of fire, electric shock
More informationQuick Reference Guide
(READ AND FALLOW ALL SAFETY INSTRUCTIONS) Quick Reference Guide How to operate the App? Step 1: Download your Free Showhome App for your smartphone at: Available on the App Store Type in the search option
More informationBrite Star Symphony of Lights Projector Light Show
Page 1 Brite Star Symphony of Lights Projector Light Show Page 2 - Search Symphony of lights projector on Google Play Store/I-tunes to download the app. How to connect your device to projector 1. click
More informationOMM200 and OMM200T. Metallurgical Microscope
OMM200 and OMM200T Metallurgical Microscope Instruction Manual (Please read the manual carefully before using the microscope) Contents Safety ----------------------------------------------------------------------------
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationModel No. ET-JPF200BE
Operating Instructions Floor Stand Kit Commercial Use Model No. ET-JPF200BE ET-JPF200WE ENGLISH FRANÇAIS ESPAÑOL DEUTSCH ITALIANO * The above illustration is of this product mounted to an optional projector.
More informationAngel Carousel. Operation Manual. Be Sure to. Read the Operation. Universal Space Amusement Equipment Ltd. Manual before Use
Angel Carousel Operation Manual Be Sure to Universal Space Amusement Equipment Ltd. Read the Operation Manual before Use CONTENTS 1. The company 2 2. Specifications...3 3. Package Contents...4 4. Installation,
More informationLightshow Box with Speaker
pg.1 Lightshow Box with Speaker ORCHESTRA of LIGHTS 1-2 6 4 8 6 Pre-programmed Christmas Songs Dance of the Sugar Plum Fairy Deck The Halls Gemmy Christmas Medley Jingle Bells Religious Medley The Gemmy
More informationPulse LED Instruction Guide
PARTS LIST Light Fixture Aquarium Frame Mounts Instruction Guide WARNING: To guard against injury, basic precautions should be observed, including the following: A) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
More informationWhisper-Ride
11/16/2007 LR (1) CAUTION: Before you begin any of the installation procedures on page 3, read and follow the warnings and safety instructions on this page. WARNING! THIS IS NOT A TOY! WARNING! CHILDREN
More informationISDN 8510T Voice Terminal Instructions for Changing the EPROM
- ISDN 8510T Voice Terminal Instructions for Changing the EPROM COMCODE 106910698 555-021-753 Issue 1, October 1992 1 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment and installing this
More informationMOBILE CONNECTOR - GEN 2 OWNER'S MANUAL
MOBILE CONNECTOR - GEN 2 OWNER'S MANUAL UNITED STATES Contents Safety Information... 2 Save These Important Safety Instructions... 2 Warnings...2 Cautions...3 General Information... 4 Mobile Connector
More informationVortex Series 2-leg Desk Assembly Guide
ELECTRIC HEIGHT-ADJUSTED SIT TO STAND DESK Vortex Series 2-leg Desk Assembly Guide For desk with underframe Model No. AL4628-XX REV-1509A Table of Contents IMPORTANT SAFETY INSTRUCTIONS... 3 CAUTION, USE
More informationATD SABER 2000 LUMENS CORDED UNDERHOOD LIGHT OWNER S MANUAL
ATD-80356 SABER 2000 LUMENS CORDED UNDERHOOD LIGHT OWNER S MANUAL FEATURES: 250 SMD LEDs provide 2,000 lumens of bright light Hooks extend 55 to 83 to t new SUV s and light trucks 40" light bar provides
More informationRAINPROOF* COLOR CAMERA SECURITY SYSTEM
RAINPROOF* COLOR CAMERA SECURITY SYSTEM Model 91202 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2004 by
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationS-100X / S-200X Snow Machine User Manual
S-100X / S-200X Snow Machine User Manual English Français Deutsch 中文 2014 Antari Lighting and Effects Ltd. 1 2 User Manual Antari S-100X & S-200X Snow Machine Introduction Thank you for choosing an ANTARI
More informationPRECAUTIONS FOR USE. Be sure to use indoor wiring within the specified voltage requirements. For extension cord, use the specified rating or more.
PRECAUTIONS FOR USE WARNING Be sure to consult an industry specialist when setting up, moving or transporting this product. This product should not be set up, moved or transported by any one other than
More information650/1000 Fresnel 650/1000 PC 300/500 Antihalo 300/500 Fresnel theatre spotlight. user manual
650/1000 Fresnel 650/1000 PC 300/500 Antihalo 300/500 Fresnel theatre spotlight user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0
More informationBluetooth Shielding Instructions
Mac mini 2012 Bluetooth Shielding Instructions 1 INTRODUCTION 1.1 STATIC PRECAUTIONS 1.2 TOOLS REQUIRED 2 DISASSEMBLY 3 SHIELDING 4 FAQ 4.1 FAQ 5 CUSTOMER SERVICE 5.1 Before Contacting Customer Service
More informationLED FOLDING WORKLIGHT TM
LED FOLDING WORKLIGHT TM LED LIGHT POWERSTRIP USB CHARGING ITM. / ART. 689211 Model: LM55812 CARE & USE INSTRUCTIONS IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY For assistance with assembly
More informationMulti-Mount for Mac Pro " to 5.25" Drive Bay Converter Bracket. Assembly & Installation Manual
Multi-Mount for Mac Pro 2009-2010 3.5" to 5.25" Drive Bay Converter Bracket Assembly & Installation Manual Introduction 1 INTRODUCTION 1.1 System Requirements 1.1.1 Computer Requirements 1.1.2 Hard Drive
More informationLine Interactive 1000VA/1400VA/2000VA Uninterruptible Power System
USER MANUAL Line Interactive 1000VA/1400VA/2000VA Uninterruptible Power System 614-06762-00 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for Line Interactive
More informationDATA DOUBLER. Apple Mac mini (2009)
DATA DOUBLER Apple Mac mini (2009) TABLE OF CONTENTS Introduction... 1 1.1 Hardware Compatibility 1.1.1 Host Computer Compatibility 1.1.2 Drive Compatibility 1.2 Package Contents 1.3 About This Manual
More informationimac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationInstruction Manual TI-7700R
Instruction Manual TI-7700R Thank you for purchasing the TI-7700R Massage Chair. Before using your massage chair, please read the contents of this instruction manual and refer to it when needed. Table
More informationUser Manual VIDEO DOOR PHONE
User Manual VIDEO DOOR PHONE CAV-35GN Thank you for purchasing COMMAX products. Please carefully read this User s Guide (in particular, precautions for safety) before using a product and follow instructions
More informationBS 287 DUAL CHANNEL POWER SUPPLY. User Manual. January 2017 V1.0
BS 287 DUAL CHANNEL POWER SUPPLY User Manual January 2017 V1.0 Table of contents 1.0 SAFETY INSTRUCTIONS... 3 2.0 GENERAL DESCRIPTION PS 289... 4 3.0 MECHANICAL INSTALLATION... 5 4.0 MAINS POWER & SAFETY
More informationHP R/T2200 UPS. Overview. Precautions. Installation Instructions. The HP UPS R/T2200 features power protection for loads up to 2200 VA/1600 W.
HP R/T2200 UPS Installation Instructions Overview The HP UPS R/T2200 features power protection for loads up to 2200 VA/1600 W. For more information about any of the topics covered in this document, see
More informationLITE TUNES #V
LITE TUNES #V45000-71 Thank you for purchasing this new Sylvania LITE TUNES. This LITE TUNES assembles in minutes. The LITE TUNES: CARTON INCLUDES: 1 Litetunes 2 Remote controls 1 Set ground stake 1 Audio
More informationUpgrading LVDS Cables Instruction Sheet
Upgrading LVDS Cables Instruction Sheet INTRODUCTION Use the following instructions to replace the LVDS cables in CP2000-M/MR projectors. The new cables are slightly longer in length and allow for better
More informationOperation Manual WARNING. Be sure to read this Operation Manual before use. Universal Space Amusement Equipment Ltd.
WARNING Be sure to read this Operation Manual before use. Universal Space Amusement Equipment Ltd. CONTENTS 1. The company..2 2. Specifications.. 3 3. Package Contents..5 4. Installation, Fix and Transport..6
More informationStereo Turntable System
3-866-873-15(1) Stereo Turntable System Operating Instructions OWNER S RECORD The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to them whenever
More informationHP UPS R/T3000 ERM. Overview. Precautions. Installation Instructions
HP UPS R/T3000 ERM Installation Instructions Overview The ERM consists of two battery packs in a 2U chassis. The ERM connects directly to a UPS R/T3000 or to another ERM. Up to two ERM units can be connected.
More informationOctostrip ORDERCODE 42220
Octostrip ORDERCODE 42220 Congratulations! You have bought a great, innovative product from Showtec. The Showtec LED Octostrip brings excitement to any venue. Whether you want simple plug-&-play action
More informationTA18 active subwoofer. user manual
TA18 active subwoofer user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 email: info@thomann.de Internet: www.thomann.de 30.11.2011 Table of contents
More informationimpact INSTRUCTIONS LiteTrek 4.0 Monolight lighting equipment and accessories
impact lighting equipment and accessories LiteTrek 4.0 Monolight INSTRUCTIONS Congratulations on your purchase of the Impact LiteTrek 4.0 Portable Monolight. Enjoy the many benefits of a portable strobe
More informationZip12. Charging Desktop Cabinet. User's Guide. Components. Tools Needed ENGLISH. Requires 2 people to remove from box. 6mm. M6 x 35mm Security Screw
User's Guide Zip12 Charging Desktop Cabinet Requires 2 people to remove from box. Components 1 A B C D E 4x 6.5mm ID 12mm OD 1mm TH Tools Needed 1x 6mm 5-sided Security Wrench 1x M6 x 35mm Security Screw
More informationATD CORDED / CORDLESS 2000 LUMENS 2 IN 1 LED UNDERHOOD LIGHT OWNER S MANUAL
ATD-80357 CORDED / CORDLESS 2000 LUMENS 2 IN 1 LED UNDERHOOD LIGHT OWNER S MANUAL FEATURES: 250 SMD LEDs provide 2,000 lumens of bright light Performance of a corded light with the convenience of a rechargeable
More informationpowerbrite led Lighting Systems & Modules
powerbrite led Lighting Systems & Modules Instructions for Model PowerBrite LED #1643, 1644, 1645, 1646, 1647, 1648 Important Safety Instructions... Page 2 Installation Instructions... Page 4 Warranty...
More informationInstallation Instructions
Please read all instructions before installing SPECIFICATIONS RT-100 Time Switch Programmable Countdown Voltage...120VAC, 60HZ Load (Single Pole Circuit) Incandescent or fluorescent lamp... 0 600 Watt
More informationWhen You Need More Than Staples. Toll Free: Fax: Electric VeloBinder Operating Instructions
When You Need More Than Staples. Toll Free: 800-658-8788 Fax: 801-927-3037 info@abcoffice.com Electric VeloBinder Operating Instructions IMPORTANT SAFEGUARDS Warning: For your protection, do not connect
More informationWireless Remote Controller Kit
INSTALLATION MANUAL Wireless Remote Controller Kit LS BRC4C8 Read these instructions carefully before installation. Keep this manual in a handy place for future reference. This manual should be left with
More informationMi50 Inverted Microscope User s Manual. Fein.
Mi50 Inverted Microscope User s Manual Fein info@feinoptic.com Mi50 Microscope Components Siedentopf Trinocular Head Stage Plate Mechanical Stage Locking Screw Hex Wrench Storage Beam Splitter Dust Protector
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More information3-OUTLET SURGE PROTECTOR WITH 4 USB PORTS MODEL: QC402. User s Manual
3-OUTLET SURGE PROTECTOR WITH 4 USB PORTS MODEL: QC402 User s Manual 1. Introduction Thank you for purchasing the papalook QC402 3-OUTLET SURGE PROTECTOR WITH 4 USB PORTS. It is necessary for user to follow
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationWritten By: Walter Galan
Replace a cracked screen on your iphone 4S. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this guide to replace the screen on your iphone 4S. After successfully
More informationMulti-Mount for Mac Pro to 5.25 Drive Bay Converter Bracket. Assembly & Installation Manual
Multi-Mount for Mac Pro 2009-2010 3.5 to 5.25 Drive Bay Converter Bracket Assembly & Installation Manual 1 INTRODUCTION 1.1 System Requirements 1.1.1 Computer Requirements 1.1.2 Hard Drive Requirements
More informationTECHNICAL INFORMATION Forensic Optical Comparator Catalog Nos. FX8B, FX8B220
SIRCHIE Products Vehicles Training Copyright 2011 by SIRCHIE All Rights Reserved. TECHNICAL INFORMATION Forensic Optical Comparator Catalog Nos. FX8B, FX8B220 INTRODUCTION The FX8B is an opaque projector
More informationV 1.0 ISSUE DATE : Feb.17, 2011
V 1.0 ISSUE DATE : Feb.17, 2011 The following safety precautions are given throughout this manual. They must be strictly followed to protect those who install, use or maintain this product as well as to
More informationTo Purchase This Game, Visit BMI Gaming Or Contact International Sales at (USA)
The following safety precautions are given throughout this manual. They must be strictly followed to protect those who install, use or maintain this product as well as to protect players, visitors and
More informationRichter Optica. Instructions for Model: HSX1 High School Microscope
Richter Optica info@richter-optica.com Instructions for Model: HSX1 High School Microscope Eyepiece 360 Rotatable Head Objectives Carrying Handle Revolving Nosepiece Rack Stop Slide Holder Focus Tension
More informationHome Network. .in.ua. User Manual. Video Door Phone CDV-40N.
Home Network User Manual Video Door Phone CDV-40N Thank Thank you you for for purchasing purchasing COMMAX COMMAX products. products. Please Please carefully carefully read read this this Userʼs Userʼs
More informationOWC Mercury Helios 2 ASSEMBLY MANUAL & USER GUIDE
OWC Mercury Helios 2 ASSEMBLY MANUAL & USER GUIDE TABLE OF CONTENTS 1. INTRODUCTION...1 1.1 MINIMUM SYSTEM REQUIREMENTS 1.1.1 Apple Mac Requirements 1.1.2 PC Requirements 1.1.3 Supported PCIe Cards 1.2
More information1 Channel Strobe Controller ORDERCODE 40226
1 Channel Strobe Controller ORDERCODE 40226 Congratulations! You have bought a great, innovative product from Showtec. The Showtec Strobe Controller brings excitement to any venue. Whether you want simple
More informationPolarization Microscope. Omano OM349P Series. User Guide
Polarization Microscope Omano OM349P Series User Guide Table of Contents Getting Started... 3 Components... 3 Technical Specifications... 5 Setup Instructions... 6 Basic Operation... 7 Changing the Light
More informationObtaining Documentation and Submitting a Service Request, page xvii Safety Warnings, page xvii Safety Guidelines, page xx
Preface Obtaining Documentation and Submitting a Service Request, page xvii Safety s, page xvii Safety Guidelines, page xx Obtaining Documentation and Submitting a Service Request For information on obtaining
More informationorban FIELD ENGINEERING BULLETIN Purpose: Units Affected: Replacement Kit, Orban Part # Replacing SSM2017 Op-Amps
orban FIELD ENGINEERING BULLETIN March 27, 2002 Orban Models: 2200, 6200, 6200S, 8200, 8282, 9200 Purpose: Due to the elimination of the SSM2017 by its manufacturer, Orban has had to choose a replacement
More informationINSTRUCTION MANUAL. * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA
INSTRUCTION MANUAL * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA INSTRUCTION MANUAL Thank you for purchasing this product. For proper usage and application,
More informationIMPULSE G2/PULSE HEIGHT ADJUSTABLE TABLE LIFTING COLUMN: DL17 CONTROL: DPF1C CONTROL BOX: CBD6S PART # CONTROL MECHANISM OVERVIEW PAGE 1 OF 6
PART # 1608996 LIFTING COLUMN: DL17 CONTROL: DPF1C CONTROL BOX: CBD6S PAGE 1 OF 6 CONTROL BOX WIRING DIAGRAM Hook for cable relief DL17 DL17 DPF1C Mains Cable BASIC HEIGHT ADJUSTABLE FUNCTIONS RAISING
More informationTA12 full-rangespeaker. user manual
TA12 full-rangespeaker user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 email: info@thomann.de Internet: www.thomann.de 30.11.2011 Table of contents
More informationAxiomet AXB Safety instructions
Axiomet AXB350 1. Safety instructions Failure to follow the instructions listed below may result in electric shock or personal injury. Please read this manual carefully and thoroughly before using this
More informationRichter Optica. Instructions for Model: MDS2 Middle School Microscope
Richter Optica info@richter-optica.com Instructions for Model: MDS2 Middle School Microscope Eyepiece 360 Rotatable Head Revolving Nosepiece Carrying Handle Objectives Rack Stop Stage Stage Clips Disc
More informationFor Sales + Purchasing Info, Click Page To Visit BMI Gaming (800)
For Sales + Purchasing Info, Click Page To Visit BMI Gaming www.bmigaming.com + 561-391-7200 (800) 746-2255 The following safety precautions are given throughout this manual. They must be strictly followed
More informationUser Manual. GUARD STATION(Gate View System) CDS-4GS
User Manual GUARD STATION(Gate View System) CDS-4GS Thank you for purchasing COMMAX products. Please carefully read this User s Guide (in particular, precautions for safety) before using a product and
More informationOV1000 Part No OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE
OV1000 Part No. 23624 OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE PRODUCT OVERVIEW User Guide: OV1000 OV1000 HEIGHT ADJUSTABLE TABLE A healthier work environment starts with the option to sit or stand throughout
More information120Ra-1 Pentium III Processor Installation Insert
120Ra-1 Pentium III Processor Installation Insert PN: 455-01614-000 Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials,
More informationAchat 110 MA active full-range speaker. user manual
Achat 110 MA active full-range speaker user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 email: info@thomann.de Internet: www.thomann.de 14.02.2012
More informationHP UPS R/T3000 G2. Overview. Precautions. Kit contents. Installation Instructions
HP UPS R/T3000 G2 Installation Instructions Overview The HP UPS R/T3000 G2 features a 2U rack-mount with convertible tower design and offers power protection for loads up to a maximum of 3300 VA/3000 W
More informationEmerson Network Power provides customers with technical support. Users may contact the nearest Emerson local sales office or service center.
Liebert PSA iton User Manual Version: V2.8 Revision date: November 14, 2005 Emerson Network Power provides customers with technical support. Users may contact the nearest Emerson local sales office or
More informationUpgrading and Servicing Guide
Upgrading and Servicing Guide Copyright Information The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing
More informationUpgrading and Servicing Guide
Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed
More informationDell Latitude C800 Service Manual
Dell Latitude C800 Service Manual Dell Latitude C800 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Screw Identification Removing and Replacing Parts System Components
More informationGreat Western Painting Assured Equipment Grounding Conductor Program OR Ground Fault Circuit Interrupter (GFCI)
Assured Equipment Grounding Conductor Program OR Ground Fault Circuit Interrupter (GFCI) GROUND FAULT CIRCUIT INTERRUPTERS Wiring design and protection. - 1926.404 Our company uses ground fault circuit
More informationVDLPROM5 SET WITH DMX CONTROL BOX + 4 COLOUR CHANGERS
SET WITH DMX CONTROL BOX + 4 COLOUR CHANGERS 1. Introduction & Features Thank you for buying the! Please read the manual carefully before bringing this device into service. This set contains 4 DMX-controlled
More informationNOTICE. Operating Instructions 150W Power Pack. How to Calculate Wattage Load for 150W Power Pack EXAMPLE
NOTICE Warning: Risk of Fire or Electrical Shock Install the power unit 5 feet (1.5 m) or more from a pool, spa, or fountain. Where the power unit is installed (a) indoors within 10 feet (3.0m) of a pool,
More informationDell Latitude V710/V740 Service Manual
Dell Latitude V710/V740 Service Manual Dell Latitude V710/V740 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification System Components
More informationPyrit 212 Sub A active subwoofer. user manual
Pyrit 212 Sub A active subwoofer user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 22.01.2013 Table
More informationUser Guide True RMS Multimeter Extech EX205T
User Guide Extech EX205T True RMS Digital Multimeter Extech EX210T True RMS Digital Multimeter IR True RMS Multimeter Extech EX205T Introduction Thank you for selecting the Extech EX205T True RMS Auto-ranging
More informationThank you for purchasing the CHP Assembly Tool. In order to ensure maximum performance and
Power Supply Instruction Manual Applicable Models: APS-301A, APS-351B, APM-301A, APM-301C Thank you for purchasing the CHP Assembly Tool. In order to ensure maximum performance and product life, please
More informationModel 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 2460-KIT Screw Terminal Connector Kit Description The Model 2460-KIT Screw Terminal Connector Kit
More informationMercury Helios ASSEMBLY MANUAL & USER GUIDE
Mercury Helios ASSEMBLY MANUAL & USER GUIDE TABLE OF CONTENTS INTRODUCTION...1 1.1 MINIMUM SYSTEM REQUIREMENTS 1.1.1 Apple Mac Requirements 1.1.2 PC Requirements 1.1.3 Supported PCIe Cards NOTE: Boot Camp
More informationBS 181 SINGLE CHANNEL POWER SUPPLY USER MANUAL
BS 181 SINGLE CHANNEL POWER SUPPLY USER MANUAL August 2016 This product is designed and manufactured by: ASL Intercom B.V. Zonnebaan 42 3542 EG Utrecht The Netherlands Phone: +31 (0)30 2411901 Fax: +31
More informationOWNER'S MANUAL. Model:PSV Amp SWITCHING DC POWER SUPPLY.
OWNER'S MANUAL Model:PSV-40 3-Amp SWITCHING DC POWER SUPPLY www.pyramidcaraudio.com FEATURES Your PYRAMID Heavy-Duty 3-Amp Switching DC Power Supply is designed to use AC power-to-power equipment that
More informationControl. Part B, Section 2. This section covers the following unit configurations. 3400V 3500V Voltage 1, 2, 3 Pump Piston (D, E, F, G)
Part B, Section 2 Model This section covers the following unit configurations. 3100V 3400V 3500V Voltage 1, 2, 3 Pump Piston (D, E, F, G) Manifold 4-Port (A) 6-Port (B or C) 2-Port (S or T) Vista Temperature
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationimac Intel 21.5" Retina 4K Display (2017) RAM
imac Intel 21.5" Retina 4K Display (2017) RAM Replacement Learn how to replace or upgrade the RAM in your 2017 Retina 4K imac. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 38 INTRODUCTION
More informationThank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com.
Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Please check out our ebay auctions for more great deals on Factory Service Manuals: servicemanuals4u Dell Latitude
More informationOV1001 Part No OV1001 HEIGHT ADJUSTABLE TABLE USER GUIDE
OV1001 Part No. 23620 OV1001 HEIGHT ADJUSTABLE TABLE USER GUIDE PRODUCT OVERVIEW User Guide: OV1001 OV1001 HEIGHT ADJUSTABLE TABLE A healthier work environment starts with the option to sit or stand throughout
More informationAntenna Distributor ORDERCODE D1444
Antenna Distributor ORDERCODE D1444 Congratulations! You have bought a great, innovative product from DAP Audio. The DAP Audio TAS series bring excitement to any venue. Whether you want simple plug-&-play
More informationUser Manual. Binocular Stereo Microscope. MicroscopeNet.com
User Manual Binocular Stereo Microscope Model K2213 Series MicroscopeNet.com Table of Contents i. Caution... 1 ii. Care and Maintenance... 1 1. Components Illustration... 2 2. Installation... 3 3. Operation...
More informationElectrical Management System (EMS) EMS-HW30C & EMS-HW50C
Electrical Management System (EMS) EMS-HW30C & EMS-HW50C Installation & Operating Guide for: Model EMS-HW30C Rated at 120V/30A and Model EMS-HW50C Rated at 240V/50A Surgio Says Lifetime Warranty on all
More information