Relion 615 series. Feeder Protection and Control REF615 DNP3 Point List Manual

Size: px
Start display at page:

Download "Relion 615 series. Feeder Protection and Control REF615 DNP3 Point List Manual"

Transcription

1 Relion 615 series Feeder Protection and Control REF615 DNP3

2

3 Document ID: 1MRS Issued: Revision: B Product version: 2.0 Copyright 2009 ABB. All rights reserved

4 Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license. Trademarks ABB and Relion are registered trademarks of ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks of their respective holders. Guarantee Please inquire about the terms of guarantee from your nearest ABB representative. ABB Oy Distribution Automation P.O. Box 699 FI Vaasa, Finland Telephone: Facsimile:

5 Disclaimer The data, examples and diagrams in this manual are included solely for the concept or product description and are not to be deemed as a statement of guaranteed properties. All persons responsible for applying the equipment addressed in this manual must satisfy themselves that each intended application is suitable and acceptable, including that any applicable safety or other operational requirements are complied with. In particular, any risks in applications where a system failure and/ or product failure would create a risk for harm to property or persons (including but not limited to personal injuries or death) shall be the sole responsibility of the person or entity applying the equipment, and those so responsible are hereby requested to ensure that all measures are taken to exclude or mitigate such risks. This document has been carefully checked by ABB but deviations cannot be completely ruled out. In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment.

6 Conformity This product complies with the directive of the Council of the European Communities on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standards EN and EN for the EMC directive, and with the product standards EN and EN for the low voltage directive. The IED is designed in accordance with the international standards of the IEC series.

7 Table of contents Table of contents Section 1 Section 2 Section 3 Section 4 Introduction...3 This manual...3 Intended audience...3 Product documentation...4 Product documentation set...4 Document revision history...5 Related documentation...6 Document symbols and conventions...6 Safety indication symbols...6 Document conventions...6 Functions, codes and symbols...7 DNP3 data mappings...11 Overview...11 Point list for REF615 Ver.2.0 FE DNP3 protocol implementation...23 DNP3 device profile...23 DNP3 implementation table...25 Glossary...29 REF615 1

8 2

9 1MRS B Section 1 Introduction Section 1 Introduction 1.1 This manual describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding Communication Protocol Manual. 1.2 Intended audience This manual addresses the communication system engineer or system integrator responsible for pre-engineering and engineering for communication setup in a substation from an IED perspective. The system engineer or system integrator must have a basic knowledge of communication in protection and control systems and thorough knowledge of the specific communication protocol. REF615 3

10 Planning & purchase Engineering Installing Commissioning Operation Maintenance Decommissioning deinstalling & disposal Section 1 Introduction 1MRS B 1.3 Product documentation Product documentation set Engineering manual Installation manual Commissioning manual Operation manual Service manual Application manual Technical manual Communication protocol manual en vsd IEC V1 EN Figure 1: The intended use of manuals in different lifecycles Engineering Manual contains instructions on how to engineer the IEDs. The manual provides instructions on how to use the different tools for IED engineering. It also includes instructions on how to handle the tool component available to read disturbance files from the IEDs on the basis of the IEC definitions. It further introduces the diagnostic tool components available for IEDs and the PCM600 tool. Installation Manual contains instructions on how to install the IED. The manual provides procedures for mechanical and electrical installation. The chapters are organized in chronological order in which the IED should be installed. Commissioning Manual contains instructions on how to commission the IED. The manual can also be used as a reference during periodic testing. The manual provides procedures for energizing and checking of external circuitry, setting and configuration as well as verifying settings and performing directional tests. The 4 REF615

11 1MRS B Section 1 Introduction chapters are organized in chronological order in which the IED should be commissioned. Operation Manual contains instructions on how to operate the IED once it has been commissioned. The manual provides instructions for monitoring, controlling and setting the IED. The manual also describes how to identify disturbances and how to view calculated and measured network data to determine the cause of a fault. Service Manual contains instructions on how to service and maintain the IED. The manual also provides procedures for de-energizing, de-commissioning and disposal of the IED. Application Manual contains application descriptions and setting guidelines sorted per function. The manual can be used to find out when and for what purpose a typical protection function can be used. The manual can also be used when calculating settings. Technical Manual contains application and functionality descriptions and lists function blocks, logic diagrams, input and output signals, setting parameters and technical data sorted per function. The manual can be used as a technical reference during the engineering phase, installation and commissioning phase, and during normal service. Communication Protocol Manual describes a communication protocol supported by the IED. The manual concentrates on vendor-specific implementations. describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding Communication Protocol Manual. Some of the manuals are not available yet Document revision history Document revision/date Product version History A/ First release B/ Content updated Download the latest documents from the ABB web site REF615 5

12 Section 1 Introduction 1MRS B Related documentation Name of the document DNP3 Communication Protocol Manual Document ID 1MRS Document symbols and conventions Safety indication symbols This publication includes icons that point out safety-related conditions or other important information. The caution icon indicates important information or warning related to the concept discussed in the text. It might indicate the presence of a hazard which could result in corruption of software or damage to equipment or property. The information icon alerts the reader to important facts and conditions. The tip icon indicates advice on, for example, how to design your project or how to use a certain function. Although warning hazards are related to personal injury, it should be understood that operation of damaged equipment could, under certain operational conditions, result in degraded process performance leading to personal injury or death. Therefore, comply fully with all warning and caution notices Document conventions Abbreviations and acronyms in this manual are spelled out in Glossary. Glossary also contains definitions of important terms. HMI menu paths are presented in bold, for example: Select Main menu/information. Parameter names are shown in italics, for example: The function can be enabled and disabled with the Operation setting. Parameter values are indicated with quotation marks, for example: The corresponding parameter values are "On" and "Off". IED input/output messages and monitored data names are shown in Courier font, for example: When the function starts, the START output is set to TRUE. 6 REF615

13 1MRS B Section 1 Introduction Functions, codes and symbols Table 1: REF615 Functions, codes and symbols Function IEC IEC IEC-ANSI Protection Three-phase non-directional overcurrent protection, low stage, instance 1 Three-phase non-directional overcurrent protection, high stage, instance 1 Three-phase non-directional overcurrent protection, high stage, instance 2 Three-phase non-directional overcurrent protection, instantaneous stage, instance 1 Three-phase directional overcurrent protection, low stage, instance 1 Three-phase directional overcurrent protection, low stage, instance 2 Three-phase directional overcurrent protection, high stage Non-directional earth-fault protection, low stage, instance 1 Non-directional earth-fault protection, low stage, instance 2 Non-directional earth-fault protection, high stage, instance 1 Non-directional earth-fault protection, instantaneous stage Directional earth-fault protection, low stage, instance 1 Directional earth-fault protection, low stage, instance 2 Directional earth-fault protection, high stage Transient / intermittent earth-fault protection Non-directional (cross-country) earth fault protection, using calculated I0 Negative-sequence overcurrent protection, instance 1 Negative-sequence overcurrent protection, instance 2 PHLPTOC1 3I> (1) 51P-1 (1) PHHPTOC1 3I>> (1) 51P-2 (1) PHHPTOC2 3I>> (2) 51P-2 (2) PHIPTOC1 3I>>> (1) 50P/51P (1) DPHLPDOC1 3I> (1) 67-1 (1) DPHLPDOC2 3I> (2) 67-1 (2) DPHHPDOC1 3I>> 67-2 EFLPTOC1 I 0 > (1) 51N-1 (1) EFLPTOC2 I 0 > (2) 51N-1 (2) EFHPTOC1 I 0 >> (1) 51N-2 (1) EFIPTOC1 I 0 >>> 50N/51N DEFLPDEF1 I 0 > (1) 67N-1 (1) DEFLPDEF2 I 0 > (2) 67N-1 (2) DEFHPDEF1 I 0 >> 67N-2 INTRPTEF1 I 0 > IEF 67NIEF EFHPTOC1 I 0 >> 51N-2 NSPTOC1 I 2 > (1) 46 (1) NSPTOC2 I 2 > (2) 46 (2) Phase discontinuity protection PDNSPTOC1 I 2 /I 1 > 46PD Residual overvoltage protection, instance 1 Residual overvoltage protection, instance 2 ROVPTOV1 U 0 > (1) 59G (1) ROVPTOV2 U 0 > (2) 59G (2) Table continues on next page REF615 7

14 Section 1 Introduction 1MRS B Function IEC IEC IEC-ANSI Residual overvoltage protection, instance 3 Three-phase undervoltage protection, instance 1 Three-phase undervoltage protection, instance 2 Three-phase undervoltage protection, instance 3 Three-phase overvoltage protection, instance 1 Three-phase overvoltage protection, instance 2 Three-phase overvoltage protection, instance 3 Positive-sequence undervoltage protection Negative-sequence overvoltage protection Three-phase thermal protection for feeders, cables and distribution transformers ROVPTOV3 U 0 > (3) 59G (3) PHPTUV1 3U< (1) 27 (1) PHPTUV2 3U< (2) 27 (2) PHPTUV3 3U< (3) 27 (3) PHPTOV1 3U> (1) 59 (1) PHPTOV2 3U> (2) 59 (2) PHPTOV3 3U> (3) 59 (3) PSPTUV1 U1< 47U+ NSPTOV1 U2> 47O- T1PTTR1 3Ith>F 49F Circuit breaker failure protection CCBRBRF1 3I>/I 0 >BF 51BF/51NBF Three-phase inrush detector INRPHAR1 3I2f> 68 Master trip, instance 1 TRPPTRC1 Master Trip (1) 94/86 (1) Master trip, instance 2 TRPPTRC2 Master Trip (2) 94/86 (2) Arc protection, instance 1 ARCSARC1 ARC (1) 50L/50NL (1) Arc protection, instance 2 ARCSARC2 ARC (2) 50L/50NL (2) Arc protection, instance 3 ARCSARC3 ARC (3) 50L/50NL (3) Control Circuit-breaker control CBXCBR1 I O CB I O CB Disconnector position indication, instance 1 Disconnector position indication, instance 2 Disconnector position indication, instance 3 DCSXSWI1 I O DC (1) I O DC (1) DCSXSWI2 I O DC (2) I O DC (2) DCSXSWI3 I O DC (3) I O DC (3) Earthing switch indication ESSXSWI1 I O ES I O ES Auto-reclosing DARREC1 O I 79 Condition Monitoring Circuit-breaker condition monitoring SSCBR1 CBCM CBCM Trip circuit supervision, instance 1 TCSSCBR1 TCS (1) TCM (1) Trip circuit supervision, instance 2 TCSSCBR2 TCS (2) TCM (2) Current circuit supervision CCRDIF1 MCS 3I MCS 3I Fuse failure supervision SEQRFUF1 FUSEF 60 Measurement Table continues on next page 8 REF615

15 1MRS B Section 1 Introduction Function IEC IEC IEC-ANSI Disturbance recorder RDRE1 - - Three-phase current measurement, instance 1 CMMXU1 3I 3I Sequence current measurement CSMSQI1 I 1, I 2, I 0 I 1, I 2, I 0 Residual current measurement, instance 1 RESCMMXU1 I 0 I n Three-phase voltage measurement VMMXU1 3U 3U Residual voltage measurement RESVMMXU1 U 0 V n Sequence voltage measurement VSMSQI1 U 1, U 2, U 0 U 1, U 2, U 0 Three-phase power and energy measurement PEMMXU1 P, E P, E REF615 9

16 10

17 1MRS B Section 2 DNP3 data mappings Section 2 DNP3 data mappings 2.1 Overview This document describes the DNP3 data points and structures available in REF615 Ver The data points are unmapped as a default.the point lists describe a superset of all data available through the standard configurations A, B, C, D, E and F including the optional functionalities. The names of the standard configurations are FE01, FE02, FE03, FE04, FE05 and FE06 respectively. The point tables show all the available DNP3 data points in this IED. The data objects in the point tables are listed in alphabetical order based on their objects' IEC61850 names. The DNP3 points can be freely added, removed, reorganized and reconfigured using PCM600. As a default, the class assignments are Class 0 and Class 1 for binary inputs and Class 0 and Class 2 for analog inputs. Analog values are provided with default scalings. The scalings can be freely be modified by the user. This list represents the superset of DNP3 points. The actual set of available points is determined by IED's ordercode. REF615 11

18 Section 2 DNP3 data mappings 1MRS B 2.2 Point list for REF615 Ver.2.0 FE REF615

19 1MRS B Section 2 DNP3 data mappings Table 2: Binary inputs IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Values Arc protection ARCPTRC11.Op.general ARCSARC1, Operate, general 1 = Operate ARCPTRC21.Op.general ARCSARC2, Operate, general 1 = Operate ARCPTRC31.Op.general ARCSARC3, Operate, general 1 = Operate ARCSARC11.FADet.stVal ARCSARC1, Fault arc detected, stval 1 = Fault arc detected ARCSARC11.InRemFA.stVal ARCSARC1, Remote fault arc detected, stval 1 = Fault arc detected ARCSARC21.FADet.stVal ARCSARC2, Fault arc detected, stval 1 = Fault arc detected ARCSARC21.InRemFA.stVal ARCSARC2, Remote fault arc detected, stval 1 = Fault arc detected ARCSARC31.FADet.stVal ARCSARC3, Fault arc detected, stval 1 = Fault arc detected ARCSARC31.InRemFA.stVal ARCSARC3, Remote fault arc detected, stval 1 = Fault arc detected Circuit breaker related signals (CB pos is found in AI) CBCILO1.EnaCls.stVal CBXCBR1, ENA_CLOSE, stval 1 = Close enabled CBCILO1.EnaOpn.stVal CBXCBR1, ENA_OPEN, stval 1 = Open enabled CBCSWI1.Pos.stSeld CBXCBR1, Switch, general, stseld 1 = CB control selected CBXCBR1.BlkCls.stVal CBXCBR1, Block closing, stval 1 = Close blocked CBXCBR1.BlkOpn.stVal CBXCBR1, Block opening, stval 1 = Open blocked Circuit breaker failure protection CCBRBRF1.InCBFlt.stVal CCBRBRF1, CB faulty and unable to trip, stval 1 = CB faulty CCBRBRF1.InPosCls.stVal CCBRBRF1, CB in closed position, stval 1 = CB closed CCBRBRF1.InStr.stVal CCBRBRF1, CBFP start command, stval 1 = CBFP start CCBRBRF1.OpEx.general CCBRBRF1, Breaker failure trip (external trip), general 1 = Breaker failure trip CCBRBRF1.OpIn.general CCBRBRF1, Operate, re-trip (internal trip), general 1 = Operate, re-trip CCBRBRF1.Str.general CCBRBRF1, Start, timer running, general 1 = Start, timer running Current circuit supervision CCRDIF1.Alm.stVal CCRDIF1, Alarm, stval 1 = Alarm CCRDIF1.Op.general CCRDIF1, Detection of current circuit failure, general 1 = Failure Three-phase current limit supervision CMMXU1.HiAlm.stVal CMMXU1, High alarm, stval 1 = High alarm CMMXU1.HiWrn.stVal CMMXU1, High warning, stval 1 = High warning CMMXU1.LoAlm.stVal CMMXU1, Low alarm, stval 1 = Low alarm CMMXU1.LoWrn.stVal CMMXU1, Low warning, stval 1 = Low warning Autoreclosing signals DARREC1.ActRec.stVal DARREC1, Active reclose status, stval 1 = AR active DARREC1.AROn.stVal DARREC1, AR switched on, stval 1 = AR switched ON DARREC1.CBManCls.stVal DARREC1, CB manually closed, stval 1 = CB manually closed DARREC1.FrqOpAlm.stVal DARREC1, Frequent operation counter alarm, stval 1 = Freq. operation alarm DARREC1.InBlkThm.stVal DARREC1, Thermal block (status), stval 1 = Thermal block DARREC1.InInhRec.stVal DARREC1, Inhibit reclose (status), stval 1 = Inhibit reclose Table continues on next page REF615 13

20 Section 2 DNP3 data mappings 1MRS B IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Values DARREC1.LO.stVal DARREC1, Lockout status, stval 1 = Lockout status DARREC1.Op.general DARREC1, Operate (close command to XCBR), general 1 = Operate, close CB DARREC1.OpOpn.general DARREC1, Operate (open command to XCBR), general 1 = Operate, open CB DARREC1.PrgCutOut.stVal DARREC1, Cutout time in progress, stval 1 = Cutout time in progress DARREC1.PrgDsr.stVal DARREC1, Discrimination time in progress, stval 1 = Discr time in progress DARREC1.PrgRec.stVal DARREC1, In progress status, stval 1 = AR in progress DARREC1.PrgRec1.stVal DARREC1, In progress 1st reclose, stval 1 = 1st reclose in progress DARREC1.PrgRec2.stVal DARREC1, In progress 2nd reclose, stval 1 = 2nd reclose in progress DARREC1.PrgRec3.stVal DARREC1, In progress 3rd reclose, stval 1 = 3rd reclose in progress DARREC1.PrgRec4.stVal DARREC1, In progress 4th reclose, stval 1 = 4th reclose in progress DARREC1.PrgRec5.stVal DARREC1, In progress 5th reclose, stval 1 = 5th reclose in progress DARREC1.ProCrd.stVal DARREC1, Protection coordination, stval 1 = Prot coordination DARREC1.RclTmStr.stVal DARREC1, Reclaim time started, stval 1 = Reclaim time started DARREC1.RdyRec.stVal DARREC1, Ready reclose status, stval 1 = Reclose ready DARREC1.SucRec.stVal DARREC1, Successful reclose status, stval 1 = Successful reclose DARREC1.UnsCBCls.stVal DARREC1, Unsuccessful CB closing status, stval 1 = Unsuccessful CB closing DARREC1.UnsRec.stVal DARREC1, Unsuccessful reclose status, stval 1 = Unsuccessful reclose DARREC1.WtMstr.stVal DARREC1, Master signal to follower, stval 1 = Master signal to follower Directional earth-fault protection DEFHPTOC1.Op.general DEFHPDEF1, Operate, general 1 = Operate DEFHPTOC1.Str.general DEFHPDEF1, Start, general 1 = Start DEFLPTOC1.Op.general DEFLPDEF1, Operate, general 1 = Operate DEFLPTOC1.Str.general DEFLPDEF1, Start, general 1 = Start DEFLPTOC2.Op.general DEFLPDEF2, Operate, general 1 = Operate DEFLPTOC2.Str.general DEFLPDEF2, Start, general 1 = Start DPHHPTOC1.Op.general DPHHPDOC1, Operate, general 1 = Operate DPHHPTOC1.Str.general DPHHPDOC1, Start, general 1 = Start Directional overcurrent protection DPHLPTOC1.Op.general DPHLPDOC1, Operate, general 1 = Operate DPHLPTOC1.Str.general DPHLPDOC1, Start, general 1 = Start DPHLPTOC2.Op.general DPHLPDOC2, Operate, general 1 = Operate DPHLPTOC2.Str.general DPHLPDOC2, Start, general 1 = Start Non-directional earth-fault and sensitive earth-fault protection EFHPTOC1.Op.general EFHPTOC1, Operate, general 1 = Operate EFHPTOC1.Str.general EFHPTOC1, Start, general 1 = Start EFIPTOC1.Op.general EFIPTOC1, Operate, general 1 = Operate EFIPTOC1.Str.general EFIPTOC1, Start, general 1 = Start EFLPTOC1.Op.general EFLPTOC1, Operate, general 1 = Operate EFLPTOC1.Str.general EFLPTOC1, Start, general 1 = Start Table continues on next page 14 REF615

21 1MRS B Section 2 DNP3 data mappings IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Values EFLPTOC2.Op.general EFLPTOC2, Operate, general 1 = Operate EFLPTOC2.Str.general EFLPTOC2, Start, general 1 = Start Three-phase inrush detection INRPHAR1.Str.general INRPHAR1, Start, general 1 = Start, general INRPHAR1.Str.phsA INRPHAR1, Start, phsa 1 = Start, phsa INRPHAR1.Str.phsB INRPHAR1, Start, phsb 1 = Start, phsb INRPHAR1.Str.phsC INRPHAR1, Start, phsc 1 = Start, phsc Transient/intermittent earth-fault protection INTRPTEF1.Op.general INTRPTEF1, Operate, general 1 = Operate INTRPTEF1.Str.general INTRPTEF1, Start, general 1 = Start Alarm LED states LEDGGIO1.SPCSO1.stVal Alarm LEDs, LED 1, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO2.stVal Alarm LEDs, LED 2, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO3.stVal Alarm LEDs, LED 3, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO4.stVal Alarm LEDs, LED 4, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO5.stVal Alarm LEDs, LED 5, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO6.stVal Alarm LEDs, LED 6, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO7.stVal Alarm LEDs, LED 7, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO8.stVal Alarm LEDs, LED 8, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO9.stVal Alarm LEDs, LED 9, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO10.stVal Alarm LEDs, LED 10, stval 1 = ON, 0 = OFF LEDGGIO1.SPCSO11.stVal Alarm LEDs, LED 11, stval 1 = ON, 0 = OFF Global conditioning LEDPTRC1.Op.general Global conditioning, Operate, general 1 = Operate LEDPTRC1.Str.general Global conditioning, Start, general 1 = Start Local/remote (also present in IIN) LLN0.Loc.stVal Control LLN0, Local / remote, stval 1 = Local LLN0.Loc1.stVal Control LLN0, Local / off, stval 1 = Off Negative-sequence overcurrent protection NSPTOC1.Op.general NSPTOC1, Operate, general 1 = Operate NSPTOC1.Str.general NSPTOC1, Start, general 1 = Start NSPTOC2.Op.general NSPTOC2, Operate, general 1 = Operate NSPTOC2.Str.general NSPTOC2, Start, general 1 = Start Negative-sequence overvoltage protection NSPTOV1.Op.general NSPTOV1, Operate, general 1 = Operate NSPTOV1.Str.general NSPTOV1, Start, general 1 = Start Phase discontinuity protection PDNSPTOC1.Op.general PDNSPTOC1, Operate, general 1 = Operate PDNSPTOC1.Str.general PDNSPTOC1, Start, general 1 = Start Table continues on next page REF615 15

22 Section 2 DNP3 data mappings 1MRS B IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Values Phase overcurrent protection PHHPTOC1.Op.general PHHPTOC1, Operate, general 1 = Operate PHHPTOC1.Str.general PHHPTOC1, Start, general 1 = Start PHHPTOC2.Op.general PHHPTOC2, Operate, general 1 = Operate PHHPTOC2.Str.general PHHPTOC2, Start, general 1 = Start PHIPTOC1.Op.general PHIPTOC1, Operate, general 1 = Operate PHIPTOC1.Str.general PHIPTOC1, Start, general 1 = Start PHLPTOC1.Op.general PHLPTOC1, Operate, general 1 = Operate PHLPTOC1.Str.general PHLPTOC1, Start, general 1 = Start Phase overvoltage protection PHPTOV1.Op.general PHPTOV1, Operate, general 1 = Operate PHPTOV1.Str.general PHPTOV1, Start, general 1 = Start PHPTOV2.Op.general PHPTOV2, Operate, general 1 = Operate PHPTOV2.Str.general PHPTOV2, Start, general 1 = Start PHPTOV3.Op.general PHPTOV3, Operate, general 1 = Operate PHPTOV3.Str.general PHPTOV3, Start, general 1 = Start PHPTUV1.Op.general PHPTUV1, Operate, general 1 = Operate PHPTUV1.Str.general PHPTUV1, Start, general 1 = Start PHPTUV2.Op.general PHPTUV2, Operate, general 1 = Operate PHPTUV2.Str.general PHPTUV2, Start, general 1 = Start PHPTUV3.Op.general PHPTUV3, Operate, general 1 = Operate PHPTUV3.Str.general PHPTUV3, Start, general 1 = Start PSPTUV1.Op.general PSPTUV1, Operate, general 1 = Operate PSPTUV1.Str.general PSPTUV1, Start, general 1 = Start Disturbance recorder RDRE1.RcdMade.stVal Disturbance recorder, recording made, stval 1 = Recording made Residual current limit supervision RESCMMXU1.HiAlm.stVal RESCMMXU1, High alarm, stval 1 = High alarm RESCMMXU1.HiWrn.stVal RESCMMXU1, High warning, stval 1 = High warning Residual voltage limit supervision RESVMMXU1.HiAlm.stVal RESVMMXU1, High alarm, stval 1 = High alarm RESVMMXU1.HiWrn.stVal RESVMMXU1, High warning, stval 1 = High warning Residual overvoltage protection ROVPTOV1.Op.general ROVPTOV1, Operate, general 1 = Operate ROVPTOV1.Str.general ROVPTOV1, Start, general 1 = Start ROVPTOV2.Op.general ROVPTOV2, Operate, general 1 = Operate ROVPTOV2.Str.general ROVPTOV2, Start, general 1 = Start ROVPTOV3.Op.general ROVPTOV3, Operate, general 1 = Operate ROVPTOV3.Str.general ROVPTOV3, Start, general 1 = Start Table continues on next page 16 REF615

23 1MRS B Section 2 DNP3 data mappings IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Values Fuse failure protection SEQRFUF1.Str.general SEQRFUF1, General start of function, general 1 = Start SEQRFUF1.Str3Ph.general SEQRFUF1, Three-phase start of function, general 1 = Start Circuit breaker condition monitoring SSCBR1.APwrAlm.stVal SSCBR1, Accumulated currents power (Iyt), exceeded alarm limit, stval 1 = Iyt alarm limit SSCBR1.APwrLO.stVal SSCBR1, Accumulated currents power (Iyt), exceeded lockout limit, stval 1 = Iyt lockout limit SSCBR1.CBLifAlm.stVal SSCBR1, Remaining life of CB exceeded alarm limit, stval 1 = Remaining life alarm SSCBR1.ClsAlm.stVal SSCBR1, CB close travel time exceeded set value, stval 1 = Close travel time alarm SSCBR1.LonTmAlm.stVal SSCBR1, CB 'not operated for long time' alarm, stval 1 = Not operated alarm SSCBR1.OpnAlm.stVal SSCBR1, CB open travel time exceeded set value, stval 1 = Open travel time alarm SSCBR1.OpNumAlm.stVal SSCBR1, Number of CB operations exceeds alarm limit, stval 1 = CB operations alarm SSCBR1.OpNumLO.stVal SSCBR1, Number of CB operations exceeds lockout limit, stval 1 = CB operations lockout SSCBR1.PresAlm.stVal SSCBR1, Pressure below alarm level, stval 1 = Low pressure alarm SSCBR1.PresLO.stVal SSCBR1, Pressure below lockout level, stval 1 = Low pressure lockout SSCBR1.SprChaAlm.stVal SSCBR1, Spring charging time has crossed the set value, stval 1 = Spring charge alarm Thermal protection T1PTTR1.AlmThm.general T1PTTR1, Thermal alarm, general 1 = Alarm T1PTTR1.Op.general T1PTTR1, Operate, general 1 = Operate T1PTTR1.Str.general T1PTTR1, Start, general 1 = Start Trip circuit supervision TCSSCBR1.CirAlm.stVal TCSSCBR1, Alarm, stval 1 = Alarm TCSSCBR2.CirAlm.stVal TCSSCBR2, Alarm, stval 1 = Alarm Global conditioning TRPPTRC1.Op.general TRPPTRC1, Operate input signal, general 1 = Operate, input TRPPTRC1.Tr.general TRPPTRC1, General trip output signal, general 1 = Trip, output TRPPTRC2.Op.general TRPPTRC2, Operate input signal, general 1 = Operate, input TRPPTRC2.Tr.general TRPPTRC2, General trip output signal, general 1 = Trip, output Three-phase voltage limit supervision VMMXU1.HiAlm.stVal VMMXU1, High alarm, stval 1 = High alarm VMMXU1.HiWrn.stVal VMMXU1, High warning, stval 1 = High warning VMMXU1.LoAlm.stVal VMMXU1, Low alarm, stval 1 = Low alarm VMMXU1.LoWrn.stVal VMMXU1, Low warning, stval 1 = Low warning Raw I/O signals XAGGIO130.Ind1.stVal X130 (AIM), X130-Input 1, stval 1 = ON, 0 = OFF XAGGIO130.Ind2.stVal X130 (AIM), X130-Input 2, stval 1 = ON, 0 = OFF XAGGIO130.Ind3.stVal X130 (AIM), X130-Input 3, stval 1 = ON, 0 = OFF XAGGIO130.Ind4.stVal X130 (AIM), X130-Input 4, stval 1 = ON, 0 = OFF XGGIO100.SPCSO1.stVal X100 (PSM), X100-Output 1, stval 1 = ON, 0 = OFF XGGIO100.SPCSO2.stVal X100 (PSM), X100-Output 2, stval 1 = ON, 0 = OFF Table continues on next page REF615 17

24 Section 2 DNP3 data mappings 1MRS B IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Values XGGIO100.SPCSO3.stVal X100 (PSM), X100-Output 3, stval 1 = ON, 0 = OFF XGGIO100.SPCSO4.stVal X100 (PSM), X100-Output 4, stval 1 = ON, 0 = OFF XGGIO100.SPCSO5.stVal X100 (PSM), X100-Output 5, stval 1 = ON, 0 = OFF XGGIO100.SPCSO6.stVal X100 (PSM), X100-Output 6, stval 1 = ON, 0 = OFF XGGIO110.Ind1.stVal X110 (BIO), X110-Input 1, stval 1 = ON, 0 = OFF XGGIO110.Ind2.stVal X110 (BIO), X110-Input 2, stval 1 = ON, 0 = OFF XGGIO110.Ind3.stVal X110 (BIO), X110-Input 3, stval 1 = ON, 0 = OFF XGGIO110.Ind4.stVal X110 (BIO), X110-Input 4, stval 1 = ON, 0 = OFF XGGIO110.Ind5.stVal X110 (BIO), X110-Input 5, stval 1 = ON, 0 = OFF XGGIO110.Ind6.stVal X110 (BIO), X110-Input 6, stval 1 = ON, 0 = OFF XGGIO110.Ind7.stVal X110 (BIO), X110-Input 7, stval 1 = ON, 0 = OFF XGGIO110.Ind8.stVal X110 (BIO), X110-Input 8, stval 1 = ON, 0 = OFF XGGIO110.SPCSO1.stVal X110 (BIO), X110-Output 1, stval 1 = ON, 0 = OFF XGGIO110.SPCSO2.stVal X110 (BIO), X110-Output 2, stval 1 = ON, 0 = OFF XGGIO110.SPCSO3.stVal X110 (BIO), X110-Output 3, stval 1 = ON, 0 = OFF XGGIO110.SPCSO4.stVal X110 (BIO), X110-Output 4, stval 1 = ON, 0 = OFF XGGIO120.Ind1.stVal X120 (AIM), X120-Input 1, stval 1 = ON, 0 = OFF XGGIO120.Ind2.stVal X120 (AIM), X120-Input 2, stval 1 = ON, 0 = OFF XGGIO120.Ind3.stVal X120 (AIM), X120-Input 3, stval 1 = ON, 0 = OFF XGGIO120.Ind4.stVal X120 (AIM), X120-Input 4, stval 1 = ON, 0 = OFF XGGIO130.Ind1.stVal X130 (BIO), X130-Input 1, stval 1 = ON, 0 = OFF XGGIO130.Ind2.stVal X130 (BIO), X130-Input 2, stval 1 = ON, 0 = OFF XGGIO130.Ind3.stVal X130 (BIO), X130-Input 3, stval 1 = ON, 0 = OFF XGGIO130.Ind4.stVal X130 (BIO), X130-Input 4, stval 1 = ON, 0 = OFF XGGIO130.Ind5.stVal X130 (BIO), X130-Input 5, stval 1 = ON, 0 = OFF XGGIO130.Ind6.stVal X130 (BIO), X130-Input 6, stval 1 = ON, 0 = OFF XGGIO130.SPCSO1.stVal X130 (BIO), X130-Output 1, stval 1 = ON, 0 = OFF XGGIO130.SPCSO2.stVal X130 (BIO), X130-Output 2, stval 1 = ON, 0 = OFF XGGIO130.SPCSO3.stVal X130 (BIO), X130-Output 3, stval 1 = ON, 0 = OFF 18 REF615

25 1MRS B Section 2 DNP3 data mappings Table 3: Binary outputs IEC LN.DO.DA IEC LN Desc, DO Desc, DAName Circuit breaker control CBCSWI1.Pos.Oper.ctlVal CBXCBR1, Switch, general, Oper.ctlVal Reset current max. demand values CMSTA1.RecRs.Oper.ctlVal CMMXU1, CMMXU1 max.demands, Oper.ctlVal Autoreclosing reset signals DARREC1.RsCnt.Oper.ctlVal DARREC1, DARREC1 counters, Oper.ctlVal DARREC1.RsRec.Oper.ctlVal DARREC1, DARREC1 reset, Oper.ctlVal Clear Indications and LEDs LLN0.LEDRs1.Oper.ctlVal General, indications and LEDs, Oper.ctlVal LLN0.LEDRs2.Oper.ctlVal General, alarm LEDs, Oper.ctlVal LLN0.RecRs.Oper.ctlVal General, all data, Oper.ctlVal Reset accumulated energy values PEMMXU1.SupDmdRs.Oper.ctlVal PEMMXU1, Reset of accumulated energy, Oper,ctlVal Disturbance recorder, clear memory and trig recording RDRE1.MemClr.Oper.ctlVal Disturbance recorder, disturbance records, Oper.ctlVal RDRE1.RcdTrg.Oper.ctlVal Disturbance recorder, trig recording, Oper.ctlVal Reset signals of circuit breaker condition monitoring SSCBR1.RsAccAPwr.Oper.ctlVal SSCBR1, Reset accumulation energy, Oper.ctlVal SSCBR1.RsCBWear.Oper.ctlVal SSCBR1, Reset input for CB remaining life and operation counter, Oper.ctlVal SSCBR1.RsSprChaTm.Oper.ctlVal SSCBR1, SSCBR1 spring charge time alarm reset, Oper.ctlVal SSCBR1.RsTrvTm.Oper.ctlVal SSCBR1, SSCBR1 travel time alarm reset, Oper.ctlVal REF615 19

26 Section 2 DNP3 data mappings 1MRS B Table 4: Analog inputs IEC LN.DO.DA Description Value range Scaling function Circuit breaker, operation counter and 4-pole (2 bit) position value Argument 1 (min value) Argument 2 (min value) Argument 3 Argument 4 CBCSWI1.OpCntRs.stVal Operation counter Ratio CBCSWI1.Pos.stVal CB switch 0 3 Ratio Phase current measurements CMMXU1.A.phsA.instCVal.mag.f Phase current A [xin] Ratio CMMXU1.A.phsB.instCVal.mag.f Phase current B [xin] Ratio CMMXU1.A.phsC.instCVal.mag.f Phase current C [xin] Ratio Phase currents demand values CMSTA1.AvAmps1.mag.f Phase current A demand [xin] Ratio CMSTA1.AvAmps2.mag.f Phase current B demand [xin] Ratio CMSTA1.AvAmps3.mag.f Phase currents C demand [xin] Ratio CMSTA1.MaxAmps1.mag.f Maximum demand for phase A [xin] Ratio CMSTA1.MaxAmps2.mag.f Maximum demand for phase B [xin] Ratio CMSTA1.MaxAmps3.mag.f Maximum demand for phase C [xin] Ratio Sequence of current measurement values CSMSQI1.SeqA.c1.instCVal.mag.f Positive Sequence Current [xin] Ratio CSMSQI1.SeqA.c2.instCVal.mag.f Negative Sequence Current [xin] Ratio CSMSQI1.SeqA.c3.instCVal.mag.f Zero Sequence Current [xin] Ratio Autoreclosing values DARREC1.AutoRecSt.stVal Autoreclosing status -2 4 (see doc) Ratio DARREC1.FrqOpCnt.stVal Frequent operation counter Ratio DARREC1.OpCnt1.stVal Operation counter (1st shot) Ratio DARREC1.OpCnt2.stVal Operation counter (2nd shot) Ratio DARREC1.OpCnt3.stVal Operation counter (3rd shot) Ratio DARREC1.OpCnt4.stVal Operation counter (4th shot) Ratio DARREC1.OpCnt5.stVal Operation counter (5th shot) Ratio DARREC1.OpCntRs.stVal Resettable operation counter (all shots) Ratio DARREC1.ShotPntr.stVal Shot pointer value Ratio Disconnector 4-pole (2 bit) position values DCSXSWI1.Pos.stVal Disconnector switch 1 position 0 3 Ratio DCSXSWI2.Pos.stVal Disconnector switch 2 position 0 3 Ratio DCSXSWI3.Pos.stVal Disconnector switch 3 position 0 3 Ratio Earth switch 4-pole (2 bit) position values ESSXSWI1.Pos.stVal Earth switch position 0 3 Ratio Device temperature, system values and counters LPHD1.NumPwrUp.stVal Number of power ups Ratio LPHD1.PhyHealth1.stVal Warning (see doc) Ratio Table continues on next page 20 REF615

27 1MRS B Section 2 DNP3 data mappings IEC LN.DO.DA Description Value range Scaling function Argument 1 (min value) Argument 2 (min value) Argument 3 Argument 4 LPHD1.PhyHealth2.stVal Internal fault (see doc) Ratio LPHD1.WacTrg.stVal Number of watchdog device resets detected Ratio LPHD1.WrmStr.stVal Number of warm starts Ratio Power measurement and accumulated power values PEMMTR1.DmdVArh.actVal Forward reactive energy (see doc) Ratio PEMMTR1.DmdWh.actVal Forward active energy (see doc) Ratio PEMMTR1.SupVArh.actVal Reverse reactive energy (see doc) Ratio PEMMTR1.SupWh.actVal Energy unit Mult (see doc) Ratio PEMMXU1.TotPF.instMag.f Average power factor (Total PF) Ratio PEMMXU1.TotW.instMag.f Total active power (Total P) (see doc) Ratio PEMMXU1.TotVA.instMag.f Total apparent power (Total S) (see doc) Ratio PEMMXU1.TotVAr.instMag.f Total reactive power (Total Q) (see doc) Ratio Disturbance recorder values RDRE1.FltNum.stVal Number of recordings Ratio RDRE1.MemUsed.stVal Rec. memory used [%] Ratio Residual current and voltage RESCMMXU1.A.res.instCVal.mag. Residual current [xin] Ratio RESVMMXU1.PhV.res.instCVal.mag.f Residual voltage [xun] Ratio Circuit breaker condition monitoring values SSCBR1.AccAPwrPhA.mag.f Accumulated currents power (Iyt), phase A Ratio SSCBR1.AccAPwrPhB.mag.f Accumulated currents power (Iyt), phase B Ratio SSCBR1.AccAPwrPhC.mag.f Accumulated currents power (Iyt), phase C Ratio SSCBR1.InaTmdCnt.stVal Number of days CB has been inactive Ratio SSCBR1.RmnLifPhA.stVal CB Remaining life phase A Ratio SSCBR1.RmnLifPhB.stVal CB Remaining life phase B Ratio SSCBR1.RmnLifPhC.stVal CB Remaining life phase C Ratio SSCBR1.TmmsCls.mag.f Travel time of the CB during closing operation [ms] Ratio SSCBR1.TmmsOpn.mag.f Travel time of the CB during opening operation [ms] Ratio SSCBR1.TmsSprCha.mag.f Charging time of the CB spring [s] Ratio Temperature protection values T1PTTR1.TmmsOp.stVal Estimated time to operate [ms] Ratio T1PTTR1.TmmsRecEna.stVal Estimated time to deactivate BLK_CLOSE [ms] Ratio T1PTTR1.Tmp.mag.f Protected object temperature [Celsius] Ratio T1PTTR1.TmpRl.mag.f Relative temperature [Celsius] Ratio T1PTTR1.TmpUsed.mag.f The ambient temperature used in the calculation [Celcius] Ratio Voltage measurement phase to ground and phase to phase values VMMXU1.PhV.phsA.cVal.mag.f Phase to ground voltage A [xun] Ratio Table continues on next page REF615 21

28 Section 2 DNP3 data mappings 1MRS B IEC LN.DO.DA Description Value range Scaling function Argument 1 (min value) Argument 2 (min value) Argument 3 Argument 4 VMMXU1.PhV.phsB.cVal.mag.f Phase to ground voltage B [xun] Ratio VMMXU1.PhV.phsC.cVal.mag.f Phase to ground voltage C [xun] Ratio VMMXU1.PPV.phsAB.instCVal.mag.f Phase to phase voltage AB [xun] Ratio VMMXU1.PPV.phsBC.instCVal.mag.f Phase to phase voltage BC [xun] Ratio VMMXU1.PPV.phsCA.instCVal.mag.f Phase to phase voltage CA [xun] Ratio Sequence of voltage measurement values VSMSQI1.SeqV.c1.instCVal.mag.f Positive Sequence Voltage [xun] Ratio VSMSQI1.SeqV.c2.instCVal.mag.f Negative Sequence Voltage [xun] Ratio VSMSQI1.SeqV.c3.instCVal.mag.f Zero Sequence Voltage [xun] Ratio REF615

29 1MRS B Section 3 DNP3 protocol implementation Section 3 DNP3 protocol implementation 3.1 DNP3 device profile The following table provides a device profile document in the standard format defined in the DNP3 Subset Definitions Document. While it is referred to in the DNP3 Subset Definitions as a document, it is in fact a table, and only a component of a total interoperability guide. The table, in combination with the Implementation table and the point list tables provides a complete configuration/interoperability guide for communicating with a device. Table 5: Device profile document DNP3 device profile document Vendor name: Device name: Highest DNP level supported: ABB Oy REF615 Device function: For requests: Level 2+ Master For responses: Level 2+ Slave Notable objects, functions, and/or qualifiers supported in addition to the highest DNP levels supported (the complete list is described in the attached table): For static (non-change-event) object requests, request qualifier codes 07 and 08 (limited quantity), and 17 and 28 (index) are supported. Static object requests sent with qualifiers 07, or 08, will be responded with qualifiers 00 or bit and 32-bit Analog Change Events with Time may be requested. Maximum data link frame size (octets): Maximum data link re-tries: Maximum application fragment size (octets): Transmitted: 292 Transmitted: Configurable ( ) Received: 292 Received: 2048 None None Maximum application layer re-tries: Fixed Configurable Configurable ( ) Requires data link layer confirmation: Never Always Sometimes Configurable as: "Never", "Only for multi-frame messages", or "Always" Requires application layer confirmation: Never Always Table continues on next page When reporting event data (slave devices only) When sending multi-fragment responses (slave devices only) REF615 23

30 Section 3 DNP3 protocol implementation 1MRS B DNP3 device profile document Timeouts while waiting for: Data link confirm: Complete appl. fragment: Application confirm: Complete appl. response: Others: Sometimes Configurable as: "Only when reporting event data", or "When reporting event data or multi-fragment messages" None Fixed at Variable Configurable None Fixed at Variable Configurable None Fixed at Variable Configurable None Fixed at Variable Configurable Select/Operate Arm Timeout, not configurable; fixed at 10s, regardless of select timeout in the HMI. Need time interval, configurable Unsolicited notification delay, configurable Unsolicited response retry delay, configurable Unsolicited offline Interval, configurable Sends/Executes Control Operations: WRITE binary outputs SELECT/ OPERATE DIRECT OPERATE DIRECT OPERATE - NO ACK Count > 1 (Count > 1 is accepted but ignored) Never Always Sometimes Configurable Never Always Sometimes Configurable Never Always Sometimes Configurable Never Always Sometimes Configurable Never Always Sometimes Configurable Pulse on Never Always Sometimes Configurable Pulse off Never Always Sometimes Configurable Latch on Never Always Sometimes Configurable Latch off Never Always Sometimes Configurable Queue Never Always Sometimes Configurable Clear queue Never Always Sometimes Configurable The circuit breaker control model is configurable for either direct or SBO mode in the circuit breaker settings. If the operation mode does not match the CROB, the returned CROB status is hardware error (4). All other control points may be controlled by either direct or SBO controls. Reports binary input change events when no specific variation requested: Sends unsolicited responses: Table continues on next page Never Never Reports time-tagged binary input change events when no specific variation requested: Only when time-tagged Binary input change with time Only non-time-tagged Binary input change with relative time Configurable to send one or the other Configurable Never Never Sends static data in unsolicited responses: 24 REF615

31 1MRS B Section 3 DNP3 protocol implementation DNP3 device profile document Default counter object/variation: Configurable When device restarts Only certain objects When status flags change Sometimes (attach explanation) ENABLE/DISABLE UNSOLICITED function codes supported No other options are permitted. Counters roll over at: No counters reported No counters reported Configurable Configurable (attach explanation) Default object Default variation: Sends multi-fragment responses: 16 bits Point-by-point list attached 32 bits Yes No Configurable Sequential file transfer support: = Selected, = Not selected Other value: Point-by-point list attached Append file mode Yes No Custom status code strings Yes No Permissions field Yes No File events assigned to class Yes No File events send immediately Yes No Multiple blocks in a fragment Yes No Max number of files open DNP3 implementation table The following table identifies which object variations, function codes, and qualifiers the IED supports in both request messages and response messages. For static (non-change-event) objects, requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01. Requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28. For change-event objects, qualifiers 17 or 28 are always responded. REF615 25

32 Section 3 DNP3 protocol implementation 1MRS B Table 6: Implementation table Object number OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) Variation number Description Function codes (dec) Qualifier codes (hex) 1 0 Binary input any variation 1 1 (default) 1) Binary input 1 2 Binary input with status 2 0 Binary input change any variation 2 1 Binary input change without time 2 2 Binary input change with time 2 3 1) Binary input change with relative time 10 0 Binary output status any variation 10 1 Binary output 12 1 Control relay output block 30 0 Analog input - any variation bit analog input Table continues on next page 1 (read) 22 (assign class) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 3 (select) 4 (operate) 5 (direct op) 6 (dir. op, noack) 1 (read) 22 (assign class) Function codes (dec) Qualifier codes (hex) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 17, 28 (index) 17, 28 (index) 17, 28 (index) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 17, 28 (index) 129 (response) echo of request 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 26 REF615

33 1MRS B Section 3 DNP3 protocol implementation OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) 30 2 (default) 1) 16-bit analog input bit analog input without flag bit analog input without flag 32 0 Analog change event any variation bit analog change event without time bit analog change event without time bit analog change event with time 32 4 (default) 1) 16-bit analog change event with time 50 0 Time and date 50 1 (default) 1) Time and date 50 3 Time and date last recorded time 51 1 Time and date CTO 51 2 Unsynchro nized time and date CTO Table continues on next page 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 17, 28 (index) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 07 (limited qty = 1l) 08 (limited qty) 2 (write) 07 (limited qty = 1l) 2 (write) 07 (limited qty) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 17, 28 (index) 17, 28 (index) 17, 28 (index) 17, 28 (index) 129 (response) 00, 01 (start-stop) 17, 28 (index) 2) 129 (response) 130 (unsol. resp) 129 (response) 130 (unsol. resp) 07 (limited qty) (qty = 1) 07 (limited qty) (qty = 1) REF615 27

34 Section 3 DNP3 protocol implementation 1MRS B OBJECT REQUEST (Library will parse) RESPONSE (Library will respond with) 52 2 Time delay fine 60 0 Not defined 60 1 Class 0 data 60 2 Class 1 data 60 3 Class 2 data 60 4 Class 3 data 80 1 Internal indications 1 (read) 06 (no range, or all) 1 (read) 06 (no range, or all) 20 (enbl. unsol.) 21 (dab. unsol.) 22 (assign class) 06 (no range, or all) 1 (read) 06 (no range, or all) 20 (enbl. unsol.) 21 (dab. unsol.) 22 (assign class) 06 (no range, or all) 1 (read) 06 (no range, or all) 20 (enbl. unsol.) 21 (dab. unsol.) 22 (assign class) 06 (no range, or all) 1 (read) 00, 01 (start-stop) 2 (write) 3) 00 (start-stop) index=7 No object (function code only) 13 (cold restart) 4) No object (function code only) 14 (warm restart) 4) No object (function code only) 23 (delay meas.) No object (function code only) 24 (record current time) 129 (response) 07 (limited qty) (qty = 1) 1) A default variation refers to the variation responded when variation 0 is requested and/or in class 0, 1, 2, or 3 scans. Default variations are configurable; however, default settings for the configuration parameters are indicated in the table above. 2) For static (non-change-event) objects, qualifiers 17 or 28 are only responded when a request is sent with qualifiers 17 or 28, respectively. Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01. (For change-event objects, qualifiers 17 or 28 are always responded.) 3) Writes of internal indications are only supported for index 7 (Restart IIN1-7) 4) Cold and warm restarts return an application layer acknowledge, but no restart action is taken. 28 REF615

35 1MRS B Section 4 Glossary Section 4 Glossary AR CB CBFP CROB CTO DA DNP3 DO EMC HMI I/O IEC IEC IED LED LN PCM600 SBO Autoreclosure Circuit breaker Circuit-breaker failure protection Control output block Common time of occurrence. The time and date CTO object is an information object that represents the absolute time of day. Data attribute A distributed network protocol originally developed by Westronic. The DNP3 Users Group has the ownership of the protocol and assumes responsibility for its evolution. Data object Electromagnetic compatibility Human-machine interface Input/output International Electrotechnical Commission International standard for substation communication and modelling Intelligent electronic device Light-emitting diode Logical node Protection and Control IED Manager Select-before-operate REF615 29

36 30

37 31

38

39

40 Contact us ABB Oy Distribution Automation P.O. Box 699 FI VAASA, Finland Phone Fax MRS B Copyright 2009 ABB. All rights reserved.

Relion 615 series. Feeder Protection and Control REF615 Modbus Point List Manual

Relion 615 series. Feeder Protection and Control REF615 Modbus Point List Manual Relion 615 series Feeder Protection and Control REF615 Modbus Document ID: 1MRS756581 Issued: 03.07.2009 Revision: C Product version: 2.0 Copyright 2009 ABB. All rights reserved Copyright This document

More information

Relion 615 series. Motor Protection and Control REM615 Modbus Point List Manual

Relion 615 series. Motor Protection and Control REM615 Modbus Point List Manual Relion 615 series Motor Protection and Control REM615 Modbus Document ID: 1MRS756877 Issued: 03.07.2009 Revision: A Product version: 2.0 Copyright 2009 ABB. All rights reserved Copyright This document

More information

Relion 615 series. Feeder protection and control REF615

Relion 615 series. Feeder protection and control REF615 Relion 65 series Feeder protection and control REF65 Compact and versatile solution for utility and industrial power distribution systems REF65 is a dedicated feeder IED perfectly aligned for the protection,

More information

Operation Manual Feeder Protection Relay REF615

Operation Manual Feeder Protection Relay REF615 Feeder Protection Relay REF615 Document ID: 1MRS756376 Issued: 02.07.2008 Revision: C Product version: 1.1 Copyright 2008 - ABB. All rights reserved Copyright This document and parts thereof must not

More information

SOFTWARE DOCUMENTATION. DNP3 Configuration / Interoperability Guide for the DATRAN XL4 DNP3 RTU

SOFTWARE DOCUMENTATION. DNP3 Configuration / Interoperability Guide for the DATRAN XL4 DNP3 RTU SOFTWARE DOCUMENTATION DNP3 Configuration / Interoperability Guide for the DATRAN XL4 DNP3 RTU Table of Contents 1 DNP V3.0 DEVICE PROFILE... 3 2 DNP V3.0 IMPLEMENTATION TABLE... 6 3 DNP V3.0 POINT LIST...

More information

SOFTWARE DOCUMENTATION. DNP3 Configuration / Interoperability Guide for the DATRAN II excel DNP3 RTU

SOFTWARE DOCUMENTATION. DNP3 Configuration / Interoperability Guide for the DATRAN II excel DNP3 RTU SOFTWARE DOCUMENTATION DNP3 Configuration / Interoperability Guide for the DATRAN II excel DNP3 RTU QTech Data Systems Ltd Unit 6 Amuri Park 404 Barbadoes Street Christchurch New Zealand Phone: +64 3 3663713

More information

RED615 ANSI Line differential protection and control

RED615 ANSI Line differential protection and control DESCRIPTIVE BULLETIN RED615 ANSI Line differential protection and control RED615 is a phase-segregated, twoend line differential protection and control relay for protection, control, measurement and supervision

More information

evd4 RBX615 Application manual

evd4 RBX615 Application manual Medium voltage products evd4 RBX615 Application manual RBX615 Standard configurations 1 1. Protection functions 3 1.1. Overcurrent protection 3 1.2. Thermal protection 3 1.3. Motor stall protection 4 1.4.

More information

Relion 615 series. Transformer Protection and Control RET615 ANSI Modbus Point List Manual

Relion 615 series. Transformer Protection and Control RET615 ANSI Modbus Point List Manual Relion 615 series Transformer Protection and Control RET615 ANSI Modbus Document ID: 1MAC207644-MB Issued: 01/20/2010 Revision: A Product version: 2.0 Copyright 2010 ABB. All rights reserved Copyright

More information

DNP 3.0 device profile for AQ (5) DNP 3.0 device profile for AQ 200

DNP 3.0 device profile for AQ (5) DNP 3.0 device profile for AQ 200 DNP 3.0 device profile for AQ 200 1 (5) DNP 3.0 device profile for AQ 200 DNP 3.0 device profile for AQ 200 2 (5) Revision: 4.0 Date: October 2018 Changes: - Added Counter support Checked By: DNP 3.0 device

More information

Feeder Protection REF615 Ver Technical Presentation. ABB Oy Distribution Automation. Prashant Ganoo Regional Product Marketing Manager

Feeder Protection REF615 Ver Technical Presentation. ABB Oy Distribution Automation. Prashant Ganoo Regional Product Marketing Manager ABB Oy Distribution Automation Prashant Ganoo Regional Product Marketing Manager Feeder Protection REF615 Ver. 1.1 Technical Presentation 9/26/2008-1 - 1MRS756407 C Self Introduction Prashant Ganoo B.E.(ELECT),

More information

Equipped with Relion technology. evd4 Breaker Integrated Protection RBX615 Operation Manual

Equipped with Relion technology. evd4 Breaker Integrated Protection RBX615 Operation Manual Equipped with Relion technology evd4 Breaker Integrated Protection RBX615 Document ID: 1MRS757100 Issued: 2011-12-13 Revision: B Product version: 2.0 Copyright 2011 ABB. All rights reserved Copyright

More information

Relion 615 Series. Motor Protection and Control REM615 ANSI DNP3 Point List Manual

Relion 615 Series. Motor Protection and Control REM615 ANSI DNP3 Point List Manual Relion 615 Series Motor Protection and Control REM615 ANSI 3 List Manual Document ID: 1MAC254287-MB Issued: 4/14/2011 Revision: B Product version: 4.0 Copyright 2011 ABB. All rights reserved. Copyright

More information

Relion 620 series. Transformer protection and control RET620 Flexibility for utility and industrial power distribution systems

Relion 620 series. Transformer protection and control RET620 Flexibility for utility and industrial power distribution systems Relion 620 series Transformer protection and control RET620 Flexibility for utility and industrial power distribution systems Compact protection and control with voltage regulation for two-winding power

More information

Relion Protection and Control. 615 series DNP3 Communication Protocol Manual

Relion Protection and Control. 615 series DNP3 Communication Protocol Manual Relion Protection and Control 615 series DNP3 Document ID: 1MRS756709 Issued: 2012-05-11 Revision: D Product version: 4.0 Copyright 2012 ABB. All rights reserved Copyright This document and parts thereof

More information

Campbell Scientific Australia DNP3 DEVICE PROFILE

Campbell Scientific Australia DNP3 DEVICE PROFILE S.UTLEY 1 1 Campbell Scientific Australia DNP3 DEVICE PROFILE Real-time monitoring and Control Systems S.UTLEY 1 2 DNP3 v.28 Device Profile Document Vendor name: Campbell Scientific, Inc. Device Name:

More information

Relion product family. Remote monitoring and control REC615 Protection of cable feeders with superior fault detection and location

Relion product family. Remote monitoring and control REC615 Protection of cable feeders with superior fault detection and location elion product family emote monitoring and control EC615 Protection of cable feeders with superior fault detection and location U12 0. 0 kv P 0.00 kw Q 0.00 kvar I2 0 A ESC A 1 15 AN DC IN CONSOE/S1 S2

More information

Relion 615 series. Transformer Protection and Control RET615 Application Manual

Relion 615 series. Transformer Protection and Control RET615 Application Manual Relion 615 series Transformer Protection and Control RET615 Document ID: 1YHT530003D05 Issued: 2014-05-14 Revision: C Product version: 4.1 Copyright 2014 ABB. All rights reserved Copyright This document

More information

Relion product family. Grid Automation Remote Monitoring and Control REC615 DNP3 Communication Protocol Manual

Relion product family. Grid Automation Remote Monitoring and Control REC615 DNP3 Communication Protocol Manual Relion product family Grid Automation Remote Monitoring and Control REC615 DNP3 Document ID: 1MRS757804 Issued: 2015-03-06 Revision: B Product version: 1.1 Copyright 2015 ABB. All rights reserved Copyright

More information

DNP Points List and Implementation

DNP Points List and Implementation S&C IntelliCap Plus Automatic Capacitor Control DNP Points List and Implementation Table of Contents Section Page Section Page DNP Points List for IntelliCap Plus Controls...1 Status Points....2 Analog

More information

Device Profile Document

Device Profile Document Voltage Regulators CL-6A Regulator Control DNP3 Device Profile Document Reference Information R225-90-11 Device Profile Document For Communications Protocol DNP3 For Use With Cooper Power Systems CL-6A

More information

Connectivity Packages. User's Guide - ANSI Version

Connectivity Packages. User's Guide - ANSI Version Connectivity Packages 1MRS756194 Issued: 30.11.2006 Version: A/30.11.2006 Connectivity Packages Contents Copyrights... 5 1. Introduction...... 7 1.1. Intended audience...... 7 1.2. Related documents.........

More information

Protection Terminal REF 54_ Protection Relay REX 521

Protection Terminal REF 54_ Protection Relay REX 521 Protection Terminal Protection Relay 1MRS755260 Issued: 02.04.2004 Version: C/22.06.2004 Protection Terminal Protection Relay Contents 1. About this manual...4 1.1. Copyrights...4 1.2. Trademarks...4

More information

Feeder Protection REF615. Product Guide

Feeder Protection REF615. Product Guide Product Guide Contents 1 Description.............................. 3 2 Standard configurations................. 3-4 3 Protection functions.................... 4-5 4 Application...........................

More information

Relion 615 series. Feeder Protection and Control REF615 Product Guide

Relion 615 series. Feeder Protection and Control REF615 Product Guide Relion 615 series Feeder Protection and Control Product Guide Contents 1. Description...3 2. Standard configurations...3 3. Protection functions...7 4. Application...9 5. Supported ABB solutions...12 6.

More information

EVO AT SERIES BATTERY CHARGER AT SERIES BATTERY CHARGER COMMUNICATIONS MANUAL. EVO - Microprocessor Controlled Float Battery Charger JA

EVO AT SERIES BATTERY CHARGER AT SERIES BATTERY CHARGER COMMUNICATIONS MANUAL. EVO - Microprocessor Controlled Float Battery Charger JA EVO P R O D U C T COMMUNICATIONS MANUAL EVO - Microprocessor Controlled Float Battery Charger JA5011-54 NOTICE! WARNING Table of Contents - ATevo TABLE OF CONTENTS 1. INTRODUCTION.....................................................

More information

DNP 3.0 & Modbus SCADA INTERFACE INSTRUCTIONS FOR 205T BASED SYSTEMS

DNP 3.0 & Modbus SCADA INTERFACE INSTRUCTIONS FOR 205T BASED SYSTEMS DNP 3.0 & Modbus SCADA INTERFACE INSTRUCTIONS - OPTION 21PQ - FOR 205T BASED SYSTEMS DNP 3.0 & Modbus SCADA INTERFACE OPTION 21PQ INSTRUCTIONS FOR 205T BASED SYSTEMS CPN114830 ECN/DATE ISSUE DATE: ECN

More information

RELION PRODUCT FAMILY Grid Automation Remote Monitoring and Control REC615 Product Guide

RELION PRODUCT FAMILY Grid Automation Remote Monitoring and Control REC615 Product Guide RELION PRODUCT FAMILY Grid Automation Remote Monitoring and Control REC615 Product Guide Contents 1. Description... 3 2. Standard configurations... 3 3. Protection functions...13 4. Application... 14 5.

More information

DNP3 V3.00 DEVICE PROFILE DOCUMENT

DNP3 V3.00 DEVICE PROFILE DOCUMENT DNP3 V3.00 DEVICE PROFILE DOCUMENT Vendor Name: DAQ Electronics. Device Name: DNP3 Master Station Server in the Callisto Computer. Date: June 8, 2000 Highest DNP Level Supported: For Requests: DNP-L3.

More information

GE MDS, LLC. NETio Series. Protocol Communications Supplement. March 2013 Part No A01, Rev. C

GE MDS, LLC. NETio Series. Protocol Communications Supplement. March 2013 Part No A01, Rev. C GE MDS, LLC. NETio Series Protocol Communications Supplement March 2013 Part No. 05-4672A01, Rev. C Modbus Protocol NETio Architectural Implementation As described in detail below, the Modbus RTU protocol

More information

Overcurrent and Earth-Fault Relay REJ 525. Technical Reference Manual

Overcurrent and Earth-Fault Relay REJ 525. Technical Reference Manual Overcurrent and Earth-Fault Relay MRS75094-MUM Issued: 4.09.998 Version: D/4..2005 Overcurrent and Earth-Fault Relay Contents. About this manual...5.. Copyrights...5.2. Trademarks...5.3. Guarantee...5.4.

More information

A36D/TPSD DNP 3.0 & Modbus SCADA INTERFACE

A36D/TPSD DNP 3.0 & Modbus SCADA INTERFACE SCADA INTERFACE INSTRUCTIONS - OPTION 21P / 21Q - FOR A36D/TPSD SYSTEMS A36D/TPSD DNP 3.0 & Modbus SCADA INTERFACE OPTION 21P / 21Q INSTRUCTIONS This manual is only valid for A36D/TPSD Chargers equipped

More information

Relion Protection and Control. 615/620 series ANSI Modbus Communication Protocol Manual

Relion Protection and Control. 615/620 series ANSI Modbus Communication Protocol Manual Relion Protection and Control 615/620 series ANSI Modbus 615 series Product version 2.0 620 series Product version 1.0 Document ID: 1MAC052634-MB Issued: 11/23/2010 Revision: D Copyright 2010 ABB. All

More information

COM600 Station Automation Series MNS is Connectivity (OPC) 3.2. User's Guide

COM600 Station Automation Series MNS is Connectivity (OPC) 3.2. User's Guide MNS is Connectivity 3.2 User's Guide 1MRS756569 Issued: 17.06.2008 Version: A/17.06.2008 User's Guide MNS is Connectivity 3.2 Contents: 1. About this manual... 5 1.1. Copyrights... 5 1.2. Trademarks...

More information

Relion 615 series Feeder Protection and Control REF615 Ver. 2.0 Technical Presentation

Relion 615 series Feeder Protection and Control REF615 Ver. 2.0 Technical Presentation Relion 615 series Feeder Protection and Control REF615 Ver. 2.0 Technical Presentation Distribution Automation May 13, 2010 1MRS756407 E Slide 1 Content REF615 Technical Presentation highlights May 13,

More information

DNP Points List and Implementation for the 6802 Vista Control

DNP Points List and Implementation for the 6802 Vista Control S&C 6800 Series Automatic Switch Control DNP Points List and Implementation for the 6802 Vista Control Table of Contents Section Page Section Page DNP Points List for 6802 Vista Control...1 6802 Status

More information

Relion Protection and Control. 615 series IEC Communication Protocol Manual

Relion Protection and Control. 615 series IEC Communication Protocol Manual Relion Protection and Control 615 series IEC 60870-5-103 Communication Protocol Manual Document ID: 1MRS756710 Issued: 2016-05-20 Revision: G Product version: 5.0 FP1 Copyright 2016 ABB. All rights reserved

More information

Content REF615 Technical Presentation

Content REF615 Technical Presentation Distribution Automation Relion 615 series Feeder Protection and Control Ver. 2.0 Technical Presentation March 30, 2010 1MRS756407 E Slide 1 Content Technical Presentation highlights March 30, 2010 Slide

More information

Relion 615 series. Line Differential Protection and Control RED615 Product Guide

Relion 615 series. Line Differential Protection and Control RED615 Product Guide Relion 615 series Line Differential Protection and Control Product Guide Contents 1. Description... 3 2. Standard configurations... 3 3. Protection functions...12 4. Application... 12 5. Supported ABB

More information

COM600 Station Automation Series External OPC Client Access 3.1. User's Guide

COM600 Station Automation Series External OPC Client Access 3.1. User's Guide COM600 Station Automation Series External OPC Client Access 3.1 1MRS755564 Issued: 10.03.2005 Version: C/21.12.2007 COM600 Station Automation Series External OPC Client Access 3.1 Contents: 1. About this

More information

Feeder Protection REF615 ANSI. Product Guide

Feeder Protection REF615 ANSI. Product Guide Product Guide Contents 1 Description............................. 3 2 Standard configurations................ 3-4 3 Protection functions................... 4-5 4 Application.......................... 6-7

More information

Generator and interconnection protection REG615 Compact and versatile solution for utility and industrial power distribution systems

Generator and interconnection protection REG615 Compact and versatile solution for utility and industrial power distribution systems Relion 65 series Generator and interconnection protection REG65 Compact and versatile solution for utility and industrial power distribution systems Compact generator and extensive interconnection protection

More information

Relion 615 series. Transformer Protection and Control RET615 Product Guide

Relion 615 series. Transformer Protection and Control RET615 Product Guide Relion 615 series Transformer Protection and Control Product Guide Contents 1. Description... 3 2. Standard configurations... 3 3. Protection functions...14 4. Application... 15 5. Supported ABB solutions...

More information

Relion Protection and Control. 615 series ANSI Modbus Communication Protocol Manual

Relion Protection and Control. 615 series ANSI Modbus Communication Protocol Manual Relion Protection and Control 615 series ANSI Modbus Document ID: 1MAC052634-MB Issued: 01/20/2010 Revision: C Product version: 2.0 Copyright 2010 ABB. All rights reserved Copyright This document and

More information

Protection System Simulator SIM600. Installation Manual

Protection System Simulator SIM600. Installation Manual Protection System Simulator SIM600 1MRS756102 Issued: 08.12.2008 Version: B Protection System Simulator SIM600 Contents: 1. About this manual... 5 1.1. Copyrights... 5 1.2. Trademarks... 5 1.3. Guarantee...

More information

Relion 620 series. Feeder protection and control REF620 Flexibility for utility and industrial power distribution systems

Relion 620 series. Feeder protection and control REF620 Flexibility for utility and industrial power distribution systems Relion 60 series Feeder protection and control REF60 Flexibility for utility and industrial power distribution systems Compact protection and control for a wide variety of feeder applications REF60 is

More information

RELION PRODUCT FAMILY Grid Automation Recloser Protection and Control RER615 Product Guide

RELION PRODUCT FAMILY Grid Automation Recloser Protection and Control RER615 Product Guide RELION PRODUCT FAMILY Recloser Protection and Control RER615 Product Guide Contents 1. Description... 3 2. Standard configurations... 3 3. Protection functions...10 4. Application... 10 5. Supported ABB

More information

Relion Protection and Control. REF615R DNP3 Communication Protocol Manual

Relion Protection and Control. REF615R DNP3 Communication Protocol Manual Relion Protection and Control REF615R DNP3 Document ID: 1MRS240048-IB Issued: 2016-10-24 Revision: B Product version: 4.1 Copyright 2016 ABB. All rights reserved Copyright This document and parts thereof

More information

Content FPC 200. USER MANUAL Mar Feeder F1 and F3 Motor M1 and M3 Busbar B2 and B3 Transformer T1 and T3

Content FPC 200. USER MANUAL Mar Feeder F1 and F3 Motor M1 and M3 Busbar B2 and B3 Transformer T1 and T3 Content FPC 200 USER MANUAL Mar 2017 Feeder F1 and F3 Motor M1 and M3 Busbar B2 and B3 Transformer T1 and T3 1 USER MANUAL FPC 200-3/2017 Content Preface Copyright Copyright Iskra d.d. Ljubljana, Slovenia

More information

Relion 615 series. Generator and Interconnection Protection REG615 Product Guide

Relion 615 series. Generator and Interconnection Protection REG615 Product Guide Relion 615 series Generator and Interconnection Protection Product Guide Contents 1. Description... 3 2. Standard configurations... 3 3. Protection functions...9 4. Application... 9 5. Supported ABB solutions...

More information

Substation Automation Products. Line differential protection RED670 Relion 670 series

Substation Automation Products. Line differential protection RED670 Relion 670 series Substation Automation Products Line differential protection RED670 Relion 670 series For maximum reliability of your power system The RED670 IED (Intelligent Electronic Device) is designed for protection,

More information

PXM 4/6/8K DNP3 PXM 4/6/8K DNP3 Ethernet Communications User Manual

PXM 4/6/8K DNP3 PXM 4/6/8K DNP3 Ethernet Communications User Manual PXM 4/6/8K DNP3 PXM 4/6/8K DNP3 Ethernet Communications User Manual Contents Contents 1. INTRODUCTION... 1 2. DNP3 PROTOCOL PRIMER... 1 2.1 Why DNP3?...1 2.2 Link Layer Responsibility...5 2.3 Static and

More information

Relion 615 series Line Differential Protection and Control RED615 Ver. 2.0 Technical Presentation

Relion 615 series Line Differential Protection and Control RED615 Ver. 2.0 Technical Presentation Relion 615 series Line Differential Protection and Control RED615 Ver. 2.0 Technical Presentation ABB Oy Distribution Automation July 1, 2009 1MRS756504 B Slide 1 Contents RED615 Technical Presentation

More information

Relion 611 series. Feeder Protection and Control REF611 Modbus Point List Manual

Relion 611 series. Feeder Protection and Control REF611 Modbus Point List Manual Relion 611 series Feeder Protection and Control REF611 Modbus Document ID: 1MRS757463 Issued: 2016-02-22 Revision: B Product version: 2.0 Copyright 2016 ABB. All rights reserved Copyright This document

More information

Feeder protection relay SPAA 121 C. Product Guide

Feeder protection relay SPAA 121 C. Product Guide Issued: April 1999 Status: Updated Version: C/06.03.2006 Data subject to change without notice Features Two-phase low-set phase overcurrent unit with definite time or inverse time characteristic Two-phase

More information

DNP3 Communication User's manual

DNP3 Communication User's manual MV Network Management Fault tracking Monitoring and Control Merlin Gerin Easergy Range T200 P, T200 I DNP3 Communication User's manual Summary General...2 Functionnalities...2 Characteristics...2 Connection

More information

Relion 620 series. Feeder Protection and Control REF620 Product Guide

Relion 620 series. Feeder Protection and Control REF620 Product Guide Relion 620 series Feeder Protection and Control Product Guide Contents 1. Description... 3 2. Default configurations...3 3. Protection functions...9 4. Application... 10 5. Supported ABB solutions... 19

More information

Protection relays.

Protection relays. Protection relays www.vamp.fi Vamp Ltd Vamp Ltd, with a strong experience of designing devices, is an independent supplier of relays and monitoring equipment. The company has an established reputation

More information

Substation Automation Products. Distributed busbar protection REB500 Communication Protocol Manual, IEC 61850

Substation Automation Products. Distributed busbar protection REB500 Communication Protocol Manual, IEC 61850 Substation Automation Products Communication Protocol Manual, IEC 61850 Document ID: 1MRK 511 342-UEN Issued: May 2015 Revision: - Product version: 8.10 Copyright 2015 ABB. All rights reserved Copyright

More information

COM600 series, Version 5.0 Modbus Serial Slave (OPC) User's Manual

COM600 series, Version 5.0 Modbus Serial Slave (OPC) User's Manual CO600 series, Version 5.0 odbus Serial Slave (OPC) User's anual 1RS756913 Issued: 9.10.2009 Version: E/24.5.2017 CO600 series, Version 5.0 odbus Serial Slave (OPC) User's anual Contents: 1. About this

More information

350 Feeder Management System

350 Feeder Management System Title page GE Digital Energy Multilin 350 Feeder Management System Feeder Protection and Control Communications Guide SR350 revision: 1.20 Manual P/N: 1601-9087-A2 GE publication code: GEK-113511B Copyright

More information

Station Automation COM Logic Processor User's Manual

Station Automation COM Logic Processor User's Manual Station Automation COM600 3.4 1MRS756738 Issued: 13.2.2009 Version: B/06.11.2009 Station Automation COM600 3.4 Contents: 1. About this manual... 5 1.1. Copyrights... 5 1.2. Trademarks... 5 1.3. General...

More information

Substation Automation Products. Bay control REC670/650 Relion 670 and 650 series

Substation Automation Products. Bay control REC670/650 Relion 670 and 650 series Substation Automation Products Bay control REC670/650 Relion 670 and 650 series For optimized control and reliable operation of your switchyard The REC670 and REC650 Bay control IEDs (Intelligent Electronic

More information

345 Transformer Protection System

345 Transformer Protection System GE Digital Energy 345 Transformer Protection System Transformer protection and control GE Digital Energy 650 Markland Street Markham, Ontario Canada L6C 0M1 TELEPHONE: Worldwide +1 905 927 7070 Europe/Middle

More information

Relion Protection and Control. 611 series Modbus Communication Protocol Manual

Relion Protection and Control. 611 series Modbus Communication Protocol Manual Relion Protection and Control 611 series Modbus Document ID: 1MRS757461 Issued: 2016-02-22 Revision: B Product version: 2.0 Copyright 2016 ABB. All rights reserved Copyright This document and parts thereof

More information

DNP V3.00 Protocol Assignments

DNP V3.00 Protocol Assignments E Electro Industries / GaugeTech "The Leader in Web Accessed Power Monitoring and Control" DNP V3.00 Protocol Assignments For Nexus 1250, 120 and 1270 Power Monitors Revision 1.5 November 7, 2002 Doc #

More information

RELION PROTECTION AND CONTROL 615 series ANSI Modbus Communication Protocol Manual

RELION PROTECTION AND CONTROL 615 series ANSI Modbus Communication Protocol Manual RELION PROTECTION AND CONTROL 615 series ANSI Modbus Communication Protocol Manual Document ID: 1MAC057386-MB Issued: 2018-02-26 Revision: A Product version: 5.0 FP1 Copyright 2018 ABB. All rights reserved

More information

NOTE The documentation and/or manuals provided by the IEDs vendors must be read and understood thoroughly prior to configuration.

NOTE The documentation and/or manuals provided by the IEDs vendors must be read and understood thoroughly prior to configuration. ConfigWiz Addendum This is the DNP3.0 client addendum. This addendum describes the pop-up window tabs, fields, and ranges of valid parameters for entry in those fields. NOTE The documentation and/or manuals

More information

Feeder protection relay SPAA 341 C. Product Guide

Feeder protection relay SPAA 341 C. Product Guide Issued: April 1999 Status: Updated Version: D/07.03.2006 Data subject to change without notice Features Comprehensive numerical feeder protection relay consisting of two multi-function protection relay

More information

Earth-fault Relay SPAJ 110 C. Product Guide

Earth-fault Relay SPAJ 110 C. Product Guide Issued: April 1999 Status: Updated Version: C/12.04.2006 Data subject to change without notice Features Low-set neutral overcurrent stage with definite time or inverse time characteristic High-set neutral

More information

Feeder protection relay

Feeder protection relay Page 1 Issued: April 1999 Status: New Data subject to change without notice Features Comprehensive numerical feeder protection relay consisting of two multi-function protection relay modules and a flexible

More information

Substation Automation Products. High impedance differential busbar protection REB650 Relion 650 series

Substation Automation Products. High impedance differential busbar protection REB650 Relion 650 series Substation Automation Products High impedance differential busbar protection REB650 Relion 650 series One IED for a wide range of high impedance differential protection applications ABB introduces a new,

More information

MiCOM P122C Time-Overcurrent Protection

MiCOM P122C Time-Overcurrent Protection Protection Relays 01 MiCOM P122C Time-Overcurrent Protection Customer Benefits 1A/5A software setting 4 function keys Compact unit for flush and wall-surface mounting Comprehensive measurements Disturbance

More information

Relion 615 series. Transformer Protection and Control RET615 Modbus Point List Manual

Relion 615 series. Transformer Protection and Control RET615 Modbus Point List Manual Relion 615 series Transformer Protection and Control RET615 Modbus Document ID: 1MRS756878 Issued: 2016-05-20 Revision: G Product version: 5.0 FP1 Copyright 2016 ABB. All rights reserved Copyright This

More information

Content FPC 400. USER MANUAL Apr Feeder F3 Motor M4 Busbar B3 Transformer T4

Content FPC 400. USER MANUAL Apr Feeder F3 Motor M4 Busbar B3 Transformer T4 Content FPC 400 USER MANUAL Apr 2017 Feeder F3 Motor M4 Busbar B3 Transformer T4 1 USER MANUAL FPC 400-4/2017 Content Preface Copyright Copyright Iskra d.d. Ljubljana, Slovenia 2016. All rights reserved.

More information

RELION PROTECTION AND CONTROL 615 series ANSI Engineering Manual

RELION PROTECTION AND CONTROL 615 series ANSI Engineering Manual RELION PROTECTION AND CONTROL 615 series ANSI Document ID: 1MAC108982-MB Issued: 2018-02-26 Revision: E Product version: 5.0 FP1 Copyright 2018 ABB. All rights reserved Copyright This document and parts

More information

DNP3 Field Device Profile. for

DNP3 Field Device Profile. for DNP3 Field Device Profile for Document Name: Eaton DNP3 XML File Revision History Date Time ion Reason for change Edited by 2012-01-11 2015-04-16 1 Initial ion Joerg Katzer 15:00:00 2 First updates Joerg

More information

Relion product family. Grid Automation Remote Monitoring and Control REC615 IEC /104 Point List Manual

Relion product family. Grid Automation Remote Monitoring and Control REC615 IEC /104 Point List Manual Relion product family Grid Automation Remote Monitoring and Control REC615 IEC 60870-5-101/104 Document ID: 1MRS757808 Issued: 2015-03-06 Revision: C Product version: 1.1 Copyright 2015 ABB. All rights

More information

Electrical Integration with Smart Communication

Electrical Integration with Smart Communication Electrical Integration with Smart Communication New possibilities with Industrial Ethernet ABB Group September 24, 2009 Slide 1 Unified Integration Approach MES and Business Systems Knowledge Portals as

More information

DNP3 Device Profile. Device Profile Template. Data Dictionary. Release 2.0. January 30, 2001

DNP3 Device Profile. Device Profile Template. Data Dictionary. Release 2.0. January 30, 2001 Reclosers Kyle Form 4C Recloser Control Serial Communications Reference Information R280-90-1 DNP3 Device Profile Device Profile Template Data Dictionary Release 2.0 January 30, 2001 For Use With Cooper

More information

Relion 620 series. Motor Protection and Control REM620 Product Guide

Relion 620 series. Motor Protection and Control REM620 Product Guide Relion 620 series Motor Protection and Control Product Guide Contents 1. Description... 3 2. Default configuration...3 3. Protection functions...9 4. Application... 9 5. Supported ABB solutions... 14 6.

More information

Relion product family. Grid Automation Remote Monitoring and Control REC615 Modbus Communication Protocol Manual

Relion product family. Grid Automation Remote Monitoring and Control REC615 Modbus Communication Protocol Manual Relion product family Grid Automation Remote Monitoring and Control REC615 Modbus Document ID: 1MRS757803 Issued: 2015-03-06 Revision: B Product version: 1.1 Copyright 2015 ABB. All rights reserved Copyright

More information

DNP Points List and Implementation

DNP Points List and Implementation S&C 6800 Series Automatic Switch Control DNP Points List and Implementation Table of Contents Section Page Section Page DNP Points List for 6801 Controls...1 6801 Status Points...2 6801 Double-bit Status

More information

Bay protection functions REB500 Application Manual

Bay protection functions REB500 Application Manual png Substation Automation Products Application Manual Document ID: 1MRK 505 353-UEN Issued: March 2016 Revision: A Product version: 8.2 Copyright 2016 ABB. All rights reserved Copyright This document

More information

MiCOM P124 T&D. Self and Dual Powered Overcurrent Relays

MiCOM P124 T&D. Self and Dual Powered Overcurrent Relays PROTECTION MiCOM P124 Self and Dual Powered Overcurrent Relays MiCOM P124 are numerical relays designed to offer complete overcurrent protection without requiring any external auxiliary supply. They can

More information

Sensitive Earth-fault Relay SPAJ 111 C. Product Guide

Sensitive Earth-fault Relay SPAJ 111 C. Product Guide Issued: April 1999 Status: Update Version: C/12.04.2006 Data subject to change without notice Features Sensitive low-set neutral overcurrent stage with definite time characteristic High-set neutral overcurrent

More information

MicroSCADA Pro SYS

MicroSCADA Pro SYS MicroSCADA Pro SYS 600 9.2 1MRS756170 Issued: 02.03.2007 Version: B/28.03.2008 MicroSCADA Pro SYS 600 9.2 Contents Copyrights...15 1. Introduction...17 1.1. This Manual...17 1.2. Use of symbols...17 1.3.

More information

Substation Automation Products. Line distance protection REL670/650 Relion 670 and 650 series

Substation Automation Products. Line distance protection REL670/650 Relion 670 and 650 series Substation Automation Products Line distance protection REL670/650 Relion 670 and 650 series For maximum reliability of your power system REL670 and REL650 line distance protection IEDs (Intelligent Electronic

More information

The Multilin DGCV Voltage Regulator Controller

The Multilin DGCV Voltage Regulator Controller GE Digital Energy The Multilin DGCV Voltage Regulator Controller Multilin DGCV Revision: 1.10 Manual P/N: 1601-0263-A1 GE publication code: GEK-113581 Copyright 2011 GE Digital Energy Communications Guide

More information

Relion 605 series. Self-powered feeder protection REJ603 Application Manual

Relion 605 series. Self-powered feeder protection REJ603 Application Manual Relion 605 series Relion 605 series Relion 605 series Self-powered feeder protection REJ603 Document ID: 1MDU07221-YN Issued: 2017-10-30 Revision: D Product version: 3.0 Copyright 2017 ABB. All rights

More information

Relion. Substation Merging Unit SMU615 Product Guide

Relion. Substation Merging Unit SMU615 Product Guide Relion Substation Merging Unit Product Guide Contents 1. Description... 3 2. Application configurations...3 3. Communication... 5 4. Application... 5 5. Process bus... 7 6. Self-supervision... 7 7. Secondary

More information

Relion 615 series Transformer Protection and Control RET615 Ver. 2.0 Technical Presentation

Relion 615 series Transformer Protection and Control RET615 Ver. 2.0 Technical Presentation Relion 615 series Transformer Protection and Control RET615 Ver. 2.0 Technical Presentation Distribution Automation May 13, 2010 1MRS756901 A Slide 1 Content RET615 Technical Presentation highlights May

More information

7SR21 Non-Directional 7SR22 Directional Overcurrent Relay

7SR21 Non-Directional 7SR22 Directional Overcurrent Relay 7SR21 Non-Directional 7SR22 Directional Overcurrent Relay Document Release History This document is issue 2010/05. The list of revisions up to and including this issue is: 2010/05 Additional Comms module

More information

DNP Points List and Implementation for Universal Controls

DNP Points List and Implementation for Universal Controls S&C 6800 Series Automatic Switch Control DNP Points List and Implementation for Universal Controls Table of Contents Section Page Section Page DNP Points List for 6801 Universal Controls...1 6801 Status

More information

Substation Automation Products. Generator protection REG670/650 Relion 670 and 650 series

Substation Automation Products. Generator protection REG670/650 Relion 670 and 650 series Substation Automation Products Generator protection REG670/650 Relion 670 and 650 series A new protection standard for your valuable assets Based on ABB s extensive experience, REG670 and REG650 IEDs (Intelligent

More information

Feeder/ Motor Protection Relay VAMP 40

Feeder/ Motor Protection Relay VAMP 40 Feeder/ Motor Protection Relay Feeder/motor protection relay Main characteristics Complete protection Comprehensive selection of protection functions for distribution network overhead line feeders, cable

More information

IEC Protocol Interoperability List

IEC Protocol Interoperability List IEC 60870-5-104 Protocol Interoperability List Network configuration Point-to-point Multiple point-to-point Multipoint-party line Multipoint-star Physical layer Transmission speed (control direction) Unbalanced

More information

IntelliCAP PLUS Supplement for Landis & Gyr Telegyr 8979 Protocol

IntelliCAP PLUS Supplement for Landis & Gyr Telegyr 8979 Protocol IntelliCAP PLUS Supplement for Landis & Gyr Telegyr 8979 Protocol March 31, 2003 1135 Atlantic Avenue Alameda, California USA 1023-563 / 3-31-03 IntelliCAP PLUS Capacitor Control Proprietary Notice This

More information

COM600 series 5.0 Operator's Manual

COM600 series 5.0 Operator's Manual COM600 series 5.0 1MRS756705 Issued: 13.2.2009 Version: F/24.5.2017 COM600 series 5.0 Contents: 1. About this manual... 5 1.1. Copyright... 5 1.2. Disclaimer... 5 1.3. Conformity... 6 1.4. Trademarks...

More information

Substation Automation Products. Transformer protection RET670/650 Relion 670 and 650 series

Substation Automation Products. Transformer protection RET670/650 Relion 670 and 650 series Substation Automation Products Transformer protection RET670/650 Relion 670 and 650 series For reliable protection and control of all types of power transformers and reactors The RET670/650 IEDs (Intelligent

More information