PowerWAVE 5000/TP. (10 50 kva) Technical Specification

Transcription

1 PowerWAVE 5000/TP (10 50 kva) Technical Specification 13

2 DOCUMENT CONTROL PDF ISSUE DATE REVISION SUMMARY TS_657_00 20/06/15 Initial published copy TS_657_01 20/0/17 Output current specification error corrected TS_657_02 19/02/19 Kohler rebranding Useful Contacts Kohler Uninterruptible Power Ltd. web site Service department booking service, fault reporting etc. Technical queries Hardware sales Extended warranty agreements etc All product, product specifications and data are subject to change without notice to improve reliability, function, design or otherwise. Kohler Uninterruptible Power Ltd. has taken every precaution to produce an accurate, complete and easy to understand specification document and will assume no responsibility nor liability for direct, indirect or accidental personal or material damage due to any misinterpretation of, or accidental errors, in this manual Kohler Uninterruptible Power Ltd. This manual may not be copied or reproduced without written permission of Kohler Uninterruptible Power Ltd.

3 POWERWAVE 5000/TP SYSTEM DESCRIPTION The availability of protected and continuous power is essential in today s dynamic IT and process-related environments, where demands can change rapidly through the introduction of new server technologies, migration and centralisation. In environments such as these, not only must the power protecting equipment be reliable but it must also be resilient and easily adaptable to suit changing load requirements attributes that are readily apparent in the PowerWAVE 5000/TP series Uninterruptible Power Supply (UPS). The PowerWAVE 5000/TP represents a completely new generation of mid-range, 3 phase UPS systems, incorporating the latest technological developments in power engineering. Its advanced double conversion, Voltage and Frequency Independent (VFI), topology fully satisfies the highest availability and environmentally-friendly requirements compliant with IEC (VFI-SS-111) standards. High reliability, upgrade ability, low operating costs and excellent electrical performance are just some of the highlights of this innovative UPS solution. The PowerWAVE 5000/TP is designed to respond to the most stringent safety, EMC and other important UPS standards. PowerWAVE 5000/TP is a stand-alone UPS module available in seven power ranges: 10, 15, 20, 25, 30, 40 & 50 kva. Each PowerWAVE 5000/TP module can operate as a stand-alone UPS, or up to 20 units can be connected in parallel to operate as a multi-module UPS system. A parallel system configuration is generally chosen either to increase the system s total output power capacity, or to provide module redundancy to enhance the overall system reliability. When operating in a parallel system, each UPS module can assume the paralleling control leadership role which avoids a single point of failure in the parallel chain and ensures the highest level of reliability. Note: Although the UPS single/multi configuration can be modified in the field it is generally specified on ordering so that the module can be configured and fully tested in the factory prior to despatch. The most demanding IT infrastructures begin with low power requirements which gradually increases as it builds up to full capacity. To avoid putting the load at risk, it is essential to be able to increase the amount of available power as the infrastructure grows. The modular design of the PowerWAVE 5000/TP system allows the parallel configuration to be expanded to cater for increasing load demands without interrupting the load or temporarily transferring it to an unprotected bypass supply. This Technical Specification provides detailed technical information on the mechanical, electrical and environmental performance of the PowerWAVE 5000/TP that can support and give answers to tender and end user requirements. KEY FEATURES Best-in-class efficiency Compact size, small foot print Blade-server-friendly power; full power from 0.9 lead to 0.73 lag Very low input current harmonic distortion THDi = load Input Power Factor near unity Energy-Operational cost savings (TCO) Expensive floor space savings No de-rating required with leading PF loads Gen-set power and installation cost savings Cost savings during installation and the entire life cycle (TCO) TS_ PW5000/TP Technical Specification 19/2/19 1

4 GENERAL SPECIFICATIONS MECHANICAL CHARACTERISTICS UPS CABINET A (without battery enclosure) Dimensions (WxHxD) mm 345 x 720 x 710 Weight without battery kg Weight with 4x7/9Ah battery kg Weight with standard packaging kg +4 Colour Black (RAL 9005) UPS CABINET B (without battery enclosure) Dimensions (WxHxD) mm 345 x 1045 x 710 Weight without battery kg Weight with 96x7/9Ah battery kg Weight with standard packaging kg +5 Colour Black (RAL 9005) UPS CABINET C (without battery enclosure) Dimensions (WxHxD) mm 440 x 1420 x 910 Weight (7/9Ah cab without battery) kg Weight (2Ah cab without battery) kg Weight with 144x7/9Ah battery kg Weight with 4x2Ah battery kg Weight with standard packaging kg +5 Colour Black (RAL 9005) INPUT CHARACTERISTICS Input Voltage V 3x30/220V+N, 00V/230V+N, 15/240V+N Input Voltage Tolerance (ref to 00/230V) for Loads in %: V (-23%/+15%) 3x30/177 V to 60/264 V for <100% load (-30%/+15%) 3x20/161 V to 60/264 V for < 0% load (-40%/+15%) 3x240/13 V to 60/264 V for < 60% load Input Frequency Hz Input Power Factor 100% load Inrush Current A max. In Input Distortion THDi Sine-wave THDi = 100% load Max. Input Power with rated output power and charged battery (output pf = 0.9) Max. Input Current with rated output power and charged battery (output pf = 0.9) kw A TS_ PW5000/TP Technical Specification 19/2/19

5 Max. Input Power with rated output power and discharged battery (output pf = 0.9) Max. Input Current with rated output power and discharged battery (output pf = 0.9) kw A OUTPUT CHARACTERISTICS Output Rated Power kva Output rated kva (400 V) A Output Rated Power KW Output rated kw (400 V) A Output Rated Voltage V 3x30/220V or 00/230V or 15/240V Output Voltage Stability % Static: < ±1% Dynamic (Step load 0%-100% or 100%-0%) < ±4% Output Voltage Distortion % With Linear Load < 2% With Non-linear Load (EN :2001) < 4% Output Frequency Hz 50 Hz or 60 Hz Output Frequency Tolerance Bypass operation Deg. Synchronized with mains < ±2% (selectable for bypass operation) or < ±4% Free running ±0.1% At input voltage of 00 V ±15%, or 196 V to 264 V ph-n Permissible Unbalanced Load (All 3 phases regulated independently) % 100% Phase Angle Tolerance (With 100% Unbalanced load) Deg. ±0 deg. Overload Capability on 0. p.f. % 125% load 10 min. 150% load 1 min. Overload Capability on 0.9 p.f. % 110% load 10 min. 130% load 1 min. Output short capability (RMS) A Inverter: up to 3 x In during 40 ms Bypass: 10 x In during 10 ms Crest - Factor 3: 1 HEAT DISSIPATION (Non-linear Loads) Heat Dissipation with 100% Non-linear Load per range (EN ) Heat Dissipation with 100% Non-linear Load per range (EN ) Airflow (25 C - 30 C) with 100% Nonlinear Load per range (EN ) W BTU/h m³/h Heat Dissipation without load W TS_ PW5000/TP Technical Specification 19/2/19 3

6 BATTERY CHARACTERISTICS Cabinet Type A B A B A B B C C C C Maximum Battery Charger Current 4A 6A Battery Charging Curve Ripple free; IU (DIN 41773) Temperature compensation ready Battery Test Battery Type Standard (temp. sensor optional) Automatic and periodically (adjustable) Maintenance free VRLA or NiCd Min/Max Number of 12V Battery Blocks per string 22-50* 32-50* 32-50* 40-50* 24-50* 32-50* 40-50* * Depending on the effective load in kw used by the system (numbers shown are for pf only) Description 10kVA 15kVA Cabinet Type A B A B Maximum Power [kw] Minimum number of battery blocks per string Maximum No. 7/9Ah battery blocks in cabinet Description 20kVA 25kVA Cabinet Type A B B C Maximum Power [kw] Minimum number of battery blocks per string Maximum No. 7/9Ah battery blocks in cabinet Maximum No. 2Ah battery blocks in cabinet N/A N/A N/A Description 30kVA 40kVA 50kVA Cabinet Type C C C Maximum Power [kw] Minimum number of battery blocks per string Maximum No. 7/9Ah battery blocks in cabinet Maximum No. 2Ah battery blocks in cabinet 4 TS_ PW5000/TP Technical Specification 19/2/19

7 COMMUNICATION OPTIONS STANDARD ITEMS Power Management Display (PMD) LCD display and mimic diagram showing UPS operational status JD1 RS232 on Sub-D9 port For monitoring and integration in network management X1 Customer Interfaces: Inputs (DRY PORTS) 1 Remote Shut down [EMERGENCY OFF (Normally closed)] 1 GEN-ON (Normally open) 1 Programmable Customer's Inputs (Normally open) 1 Battery Temperature Sensor for enhanced battery charging control 1 12Vdc source (max. 250mA) to supply remote monitor JR1 RJ45 port For multidrop purpose (optional) OPTIONAL ITEMS Relay card +USB Including: X2 Customer Interfaces: Outputs (DRY PORTS) RS232 on USB Port SNMP Card (slot already included) Common Alarm Load on Bypass Battery Low Load on Inverter Mains Failure For remote signalling and automatic computer shutdown For monitoring and integration into network management ENVIRONMENTAL Audible Noise with 100% / 50% Load dba 55/49 55/49 57/49 57/49 5/50 59/50 59/50 Operating temperature C 0-40 Battery temperature C 20 Battery Storage Time Max. 6 months Max. altitude (above sea level) m 1000m (3300ft) without de-rating De-rating factor for use at altitudes above 1000m sea level according (IEC ) ALL MODULES Metres above sea level (m / ft) De-Rating Factor for Power 1500 / / / / Relative Air-humidity Positional Clearances Accessibility (Operator) Max. 95% (non-condensing) Front: A minimum of 900mm should be allowed for free passage. Side: 600mm left and right side access is required for service. Rear: A minimum of 200mm is required for cooling air circulation and the unit should be cabled such that it can be pulled forward to allow 600mm rear clearance for service/maintenance. 10kVA 25kVA in type A or B cabinets require front/rear access 25kVA 50kVA in type C cabinets require front access only TS_ PW5000/TP Technical Specification 19/2/19 5

8 ENVIRONMENTAL Input and Output Power Cabling Efficiency AC-AC up to (at pf=1.0) (depending on UPS power) 10kVA 25kVA in type A or B cabinets are cabled at the rear 25kVA 50kVA in type C cabinets are cabled at the front Load: 100% 75% 50% 25% Efficiency: 95.5% 95.5% 95% 94.5% ECO Mode efficiency at 100% load % 9% STANDARDS Safety Electromagnetic Compatibility IEC/EN :2003, IEC/EN :2001/A11:2004 IEC/EN :2005, IEC/EN :2000, IEC/EN :2001, EMC Classes C2 domestic or industrial In < 16A C3 industrial In >16A Performance Product certification C2 IEC/EN :2001 CE C3 Degree of protection IP 20 6 TS_ PW5000/TP Technical Specification 19/2/19

9 COMMUNICATION OPTION DETAILS Power management display (PMD) Mimic LED Indicators Power Management Display (PMD) Mimic LED Indicators Alarm & Reset The user-friendly Power Management Display provides access to all monitoring information and operator controls. Mimic Diagram The mimic diagram contains multi-coloured LEDs that change between Green, Red and Off to indicate the UPS operation and power flow status. LEDs LINE 1 and LINE 2 indicate the availability of the input mains and bypass mains power supplies respectively, and are both Green during normal operation. The INVERTER and BYPASS LEDs indicate which of the two power sources is providing the critical load supply. These LEDs illuminate Green to indicate which is the active supply source. The BATTERY LED indicator is a solid Green when the battery is being charged and flashes when the battery is discharging e.g. when it is providing the load power following a mains failure. The ALARM LED, located at the lower-centre area of the PMD, is a visual indication of any monitored internal or external alarm condition. When activated, it is accompanied by an audible alarm that can be cancelled by pressing the RESET button. LCD Display Panel The 2 x 20 character multi-function LCD Display is menu-driven using the UP, DOWN and ENTER keys. It provides a simple communications interface that enables the operator to monitor important UPS operating parameters and alarm warnings, and effect various control operations such transferring the load between the inverter and bypass. LCD Display Panel summary: Displays the input and output voltage, current, frequency and power Displays an Event register which stores a date/time stamped history of the 99 most recent alarms Enables battery run time monitoring Enables selection of commands such as UPS Start-up and Shut-down, Load transfer from inverter to bypass and vice-versa Provides diagnostic facilities (service mode only) In conjunction with the operator keys, provides UPS adjustments and testing facilities (service mode only) JD1 Smart Port Serial RS 232 and USB Port Menu Navigation & Selection Buttons Module ON/OFF Control Buttons JD1is a standard D-Type, 9-pin, female socket, and the USB is a standard USB port. The SMART PORT is an intelligent RS 232 serial port that allows the UPS to be connected to a computer. When used in conjunction with the optional SMART PORT software, WAVEMON, it enables the computer to continuously monitor the mains voltage and UPS-status, and display a message in the event of any UPS system changes. TS_ PW5000/TP Technical Specification 19/2/19 7

10 X1 Dry Port (volt-free contacts) All the input and output interface connections to X1 are made to Phoenix terminals (cable 0.5mm²) Connection of Remote Shut down facilities, Generator Operation, Customers specials. Terminal Contact Signal Function X1/1 In +12Vdc GENERATOR OPERATION X1/2 Gnd Gnd (NC = Generator ON) X1/3 In +12Vdc Customer IN 1 X1/4 Gnd Gnd (Function on request, to be defined) X1/5 In +3.3Vdc BATTERY TEMPERATURE X1/6 Gnd Gnd If connected, the battery charger current is temperature dependent X1/7 In +12Vdc REMOTE SHUTDOWN X1/ Gnd Gnd Do not remove the factory mounted bridge until an external remote shut down is connected X1/9 In +12Vdc 12Vdc SOURCE X1/10 Gnd Gnd Max 200mA load (e.g. used to power remote indicator panels) JR1 RS45 Interface for multidrop The Computer Interface JR1 is an intelligent RS45 serial port that allows system information to be gained from all modules that are connected in parallel using the Multidrop connection kit. The connector JR1 is a standard RJ45 socket. X2 Dry Port Optional output interfaces terminal block (X2) All the input and output interface connections to X2 are made to Phoenix terminals (cable 0.5mm²) X2 provides status and alarm signal outputs that can be used to initiate orderly shutdown of servers, AS400 or automated building management systems. All signals are provided via voltage free contacts are rated 60 VAC / 500 ma maximum. Pin Contact Signal Function 1 NO Alarm MAINS_OK Mains Present 2 NC Mains Not Present 3 Com Common 4 NO Message LOAD_ON_INV Load On Inverter 5 NC Load Not On Inverter 6 Com Common 7 NO Alarm BATT_LOW Battery Low NC Battery OK 9 Com Common 10 NO Message LOAD_ON_MAINS Load On Mains 11 NC Load Not On Mains 12 Com Common 13 NO Alarm COMMON_ALARM Common Alarm 14 NC No Alarm Condition 15 Com Common TS_ PW5000/TP Technical Specification 19/2/19

11 Modem/Ethernet card / PowerREPORTER management software UPS systems Optional Interface Card MODEM SSL INTERNET Communication Interface (PLC s) 1.10 Management Station Alarm Situation Problem in the System Call back Modem GSM Modem Network interface (ethernet) MODEM Co mmunication Interface (PLC s) INTERNET PowerREPORTER PowerREPORTER is a remote monitoring and management service which is a part of the premium power protection concept. Two solution cards are available to enable connection between the UPS and the outside world: Modem/ Ethernet or Modem/GSM. PowerREPORTER : Provides affordable, continuous monitoring over mission-critical facilities and offers peace-of-mind by detecting and warning of any potential system problems before they become a crisis: Acquires key performance parameters and productivity information in real-time to enable you to better understand machine performance and faster troubleshoot downtime events. Gives total transparent information concerning all actions performed on the system, such as all critical status changes, coordination of equipment service, reporting of all alarms with priorities. Key Features Redundant and secure communication Alarm acknowledgment Priority driven Management (with escalation) Comprehensive Management System Reception and management of alarm calls from UPS Storage of UPS Data in a database exportable in a CSV-format for easy handling in Excel Unlimited number of UPS that can be managed User administration with passwords and permission-level Administration of Log file Data logging with statistical analysis and diagnostics, report Visualization of the UPS data Current status ( single and parallel operation) Measured values for single or three phase Recording function including graphs with zooming capabilities for selected measured values Display of event log file Display of UPS Parameters Web Server functionality, for data access from any Web Browser TS_ PW5000/TP Technical Specification 19/2/19 9

12 SNMP card/adaptor for network management/remote monitoring UPS External SNMP Adapter Ethernet Internal SNMP Card The Simple Network Management Protocol (SNMP) is a world-wide standardised communication-protocol that is used to monitor any device in a network via a simple control language. The UPS-Management Software (WAVEMON) provides data in this SNMP format with its internal software agent and can be used with any SNMP compatible operating system. We offer our software with SNMP functionality together with NetWare, OS/2, all Windows NT systems on INTEL and ALPHA. There are two types of SNMP-Adaptors available: External SNMP-Adaptor and Internal SNMP-Card (both have the same functionality). Both can manage a parallel system (N modules) and return either global values which are consistent for the whole parallel system or specific values from the individual modules. The SNMP adaptor requires a PC with terminal connections, and for normal operation at least one network connection (Ethernet) is also required. 10 TS_ PW5000/TP Technical Specification 19/2/19

13 INSTALLATION PLANNING The following guidelines should be taken into account when planning a suitable UPS location and environment. Location considerations summary The equipment must be installed and transported in a upright position The floor at the installed location and en-route from the off-loading point must be able to safely take the weight of the UPS and battery equipment The floor material where the UPS is to be located should be non-flammable Local fire protection standards must be respected Ensure that appropriate power supplies are available and that UPS cabling can be performed easily The location must be vibration free If the UPS is to be installed in bayed enclosures, partition walls must be installed. Environmental considerations summary Avoid high ambient temperature, moisture and humidity. Humidity (< 90% non-condensing) and temperature (+15 C / +25 C) are within prescribed limits A temperature of 20 C is recommended to achieve a long battery life. Any prescribed air cooling flow must be available. Ensure the air conditioning system can provide a sufficient amount of air cooling to keep the room at, or below, the maximum desired temperature. Ensure no dust or corrosive/explosive gases are present CLEARANCES X Y* V Y* X BATTERY CABINET (option) UPS Front Front Access Space V 600 mm X 600 mm Z Z Y* 200 mm Z 900 mm The above diagram illustrates the recommended clearances to be provided around the UPS and optional Battery Cabinet. Please read the following notes for clarification. Notes 1. The minimum 200mm space shown at the rear of the UPS [Y] is required to allow adequate cooling air flow; however, A and B UPS cabinets are cabled from the rear and the UPS power switches and fuses are located on the back panel. When installing A and B UPS cabinets you should allow sufficient slack in the cabling to pull the UPS cabinet forward or otherwise install the UPS with sufficient rear clearance to allow cable and switch access. 2. The above diagram shows 600mm clearance [V] between the UPS and optional Battery Cabinet. This is necessary to gain side access to the UPS for service repair. In the case of a type A or B UPS cabinet, if the cabling is sufficient to allow the cabinet to be pulled forward clear of the Battery Cabinet (see note 1 above) then it is not necessary to observe clearance [V], and the UPS and Battery Cabinets can be located immediately adjacent to each other. TS_ PW5000/TP Technical Specification 19/2/19 11

14 UPS POWER CABLING Cabinets A & B (10-25kVA) All power cables are connected to terminals on the bottom of the UPS Power Board accessed through a removable panel on the lower back of the UPS. Ex. Batt. Earth Input Mains Bypass Mains UPS Output Earth + N PE 1L2 1N 2L2 2N 3L2 3N PE PE 1L1 1L3 2L1 2L3 3L1 3L3 PE Cabinet C (25-50kVA) All power cables are connected to terminal blocks mounted on a DIN rail located in the lower front of the UPS. + N 1L1 1L2 1L3 1N PE 3L1 3L3 PE PE 2L1 2L2 2L3 2N 3N 3L2 PE Terminal Connections Battery (+ / N / - / PE) Input Bypass (3 + N) Input Mains (3+N+PE) Output Load (3+N+PE) Max Cable Section Tightening Torque Cabinets A & B (10-25kVA) 4 x 16mm² 5 x 16mm² 16mm² 1.5 Nm Cabinet C (25-50kVA) 4 x 35mm² 5 x 35mm² 16mm² 3.5 Nm The UPS input/bypass terminals should be connected to the input mains/bypass supply through a LV-Distribution board and protected by a circuit breaker or fuse. This provides overload protection and also a means of isolating the UPS from the mains supply when required. Similarly, the UPS output terminals should be connected to the load equipment via a suitably fused load distribution panel. Note: It is the customer s responsibility to provide all external fuses, isolators and cables used to connect the UPS input and output power supplies. The UPS can be wired with a single feed input (standard), whereby the UPS input supply is internally connected to the UPS bypass circuit, or it can be wired with a dual feed input (shown above) where the UPS bypass circuit is connected to a dedicated bypass supply. Where a single feed is used, the Input Mains and Bypass terminals are linked together on the UPS power connector blocks. The following diagram identifies the UPS input/output cabling requirements and provides information regarding the necessary fuse and cable ratings, and cable sizing. 12 TS_ PW5000/TP Technical Specification 19/2/19

15 Fuses & Cables Quick Reference SINGLE INPUT FEED (standard) Fuse A Mains (3x30/220V, 00/230V, 15/240V) DUAL INPUT FEED Fuse B Fuse C Cable A Cable B Cable C FA1 FA2 FA1 FA2 FA3 (F1) Rectifier FA3 (F1) Rectifier FA4 Inverter FA4 Inverter EXTERNAL BATTERY CABINET (option) Internal Batts. Static Switch Output Switch IA2 Maint. Bypass IA1 EXTERNAL BATTERY CABINET (option) Internal Batts. Static Switch Output Switch IA2 Maint. Bypass IA1 Single input feed Load Cable D Load Cable D Power (kva) Fuse A (Agl/CB) (A) Cable A (mm²) Cable D (mm²) 10 3 x 20 5 x x x 32 5 x x x 40 5 x x x 40 5 x x x 63 5 x 10 5 x x 0 5 x 25 5 x x 0 5 x 25 5 x 25 Dual input feed Power (kva) Fuse B (Agl/CB)(A) Cable B (mm²) Fuse C (Agl/CB)(A) Cable C (mm²) Cable D (mm²) 10 3 x 20 5 x x 20 5 x x x 32 5 x x 32 5 x x x 40 5 x x 40 5 x x x 40 5 x x 40 5 x x x 63 5 x 10 3 x 63 5 x 10 5 x x 0 5 x 25 3 x 0 5 x 25 5 x x 0 5 x 25 3 x 0 5 x 25 5 x The fuse and cable rating details in the above tables are a recommendation only. 2. The UPS must be installed to prescribed IEC or local regulations (e.g. BS7671:200). 3. External DC Cables and Battery fuses are bespoke to the installation. TS_ PW5000/TP Technical Specification 19/2/19 13