DIN Rail. user manual Models , & INT /503556/ UM
|
|
- Julius Griffith
- 5 years ago
- Views:
Transcription
1 DIN Rail Power Supply user manual Models , & INT /503556/ UM
2 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS DIN Rail Power Supply, Model (45 W / 2 A), Model (75 W / 3.2 A) or Model (120 W / 5 A). This series of industrial power supplies provides reliable DC power for any industrial Ethernet 24 V DC media converter or switch. Presenting a rugged design, incorporating all international standards and approvals, and offering short circuit, overload, over-voltage and over-temperature protection, these high-quality power supplies have passed a 100% full-load burn-in test and are UL/cUL listed, TUV/CB certified and CE marked. Easy-to-follow instructions in this user manual help make installation of the switch quick and simple, so you ll also soon be enjoying the benefits of these additional features: Universal AC input ( V AC) DC-compatible input ( V DC) Simple snap-on installation for TS35/7.5 or TS35/15 DIN rails Free-air cooling convection Built-in EMI filter and low ripple noise Lifetime Warranty mounting/installation Prior to installation, make sure that the power supply will be properly ventilated for adequate heat dissipation. Do not cover the top or bottom surfaces of the unit. When installing multiple units, leave enough space between them for cooling. Forcing air over the unit(s) improves heat dissipation. Each of these DIN Rail Power Supply models will attach to TS35/7.5 or TS35/15 DIN rails. 1. Insert the upper part of the DIN rail clip on the power supply into the DIN rail track.
3 2. Pull down the plastic DIN rail lock beneath the clip and push the bottom of the clip into the track. 3. Release the lock and check that the clip is securely positioned in the track. wiring/connections Model (45 W / 2 A) Connecting to DC Output: Insert the positive and negative wires into the +V terminal contact (Pin 6 or 7) and V terminal contact (Pin 4 or 5), then tighten the terminal screws to prevent the wires from becoming loose. NOTE: Always make sure that DC wiring is connected with the correct polarity. Connecting to AC Input: Insert the AC power lines into the Pin 1 and Pin 2 terminal contacts, then tighten the terminal screws to prevent the AC wires from becoming loose. Connecting to Ground: Connect the frame ground (Pin 3) of the power supply to any nearby reliable ground with a thick wire to help ensure safety and prevent system noise. Pin 1 Pin 9 Pin No. Assignment 1 AC/ L 2 AC/ N 3 Ground 4/5 DC Output V 6/7 DC Output +V 8 LED 9 +V Adj.
4 Model (75 W / 3.2 A) & (120 W / 5 A) Connecting to DC Output: Insert the positive and negative wires into the +V terminal contact (Pin 1 or 2) and V terminal contact (Pin 3 or 4) of Terminal Board 2, then tighten the terminal screws to prevent the wires from becoming loose. NOTE: Always make sure that DC wiring is connected with the correct polarity. Connecting to AC Input: Insert the AC power lines into the Pin 2 and Pin 3 terminal contacts of Terminal Board 1, then tighten the terminal screws to prevent the AC wires from becoming loose. Connecting to Ground: Connect the frame ground (Pin 1) of Terminal Board 1 of the power supply to any nearby reliable ground with a thick wire to help ensure safety and prevent system noise. Pin 1 Terminal Board (TB) 2 Terminal Board 2 Pin No. Assignment 1/2 DC Output +V 3/4 DC Output V Terminal Board 1 Pin No. 1 Ground 2 AC/ N 3 AC/ L Assignment Pin 1 Terminal Board (TB) 1
5 specifications Model General Power supply: - Input voltage: V AC, V DC - Output: 45 W, 24 V DC, 2 A Output voltage tolerance: +/- 1% Output rated current: 2 A Output current range: 0 2 A Ripple and noise: 480 mvp-p Line regulation: +/- 1% Load regulation: +/- 1% Efficiency: 80% DC voltage adjust: +/- 10% Setup, rise and holdup time: 800 ms, 60 ms and 50 ms / 230 V Operation Protection Inrush current: cold start at 30 A / 115 V or 60 A / 230 V Leakage current: < 1 ma / 240 V AC Withstand voltage: - Between input & output: 3 kv AC - Between input & frame ground: 1.5 kv AC - Between output & frame ground: 0.5 kv AC Isolation resistance: between input & output / input & frame ground / output & frame ground: 500 V DC / 100 Ohms Overload protection: %; type: constant current limiting; reset: auto recovery Over-voltage protection: V DC LEDs Power Environmental Dimensions: 78 x 96 x 67 mm (W x H x D) (3.0 x 3.8 x 2.6 in.) Weight: 400 g (0.9 lbs.) Operating temperature: C ( F) Operating humidity: 5 90% RH, non-condensing Storage temperature: C ( F) Regulatory Approvals EMC: - CISPR22 (EN55022) Class B - EN EN EN EN EN EN EN EN EN ENV50204 Safety: - UL508 - CE/EN60950
6 Model General Power supply: - Input voltage: V AC, V DC - Output: 76.8 W, 24 V DC, 3.2 A Output voltage tolerance: +/- 1% Output rated current: 2 A Output current range: A Ripple and noise: 480 mvp-p Line regulation: +/- 0.5% Load regulation: +/- 1% Efficiency: 80% DC voltage adjust: V Setup, rise and holdup time: ms, 60 ms, 50 ms / 230 V ms, 60 ms, 10 ms / 115 V Operation Protection Inrush current: cold start at 30 A / 115 V or 60 A / 230 V Leakage current: < 1 ma / 240 V AC Withstand voltage: - Between input & output: 3 kv AC - Between input & frame ground: 1.5 kv AC - Between output & frame ground: 0.5 kv AC Isolation resistance: between input & output / input & frame ground / output & frame ground: 500 V DC / 100 Ohms Overload protection: %; type: constant current limiting; reset: auto recovery Over voltage protection: V DC Over temperature protection: 85 C +/- 5 C, power shutdown LEDs DC OK Environmental Dimensions: 55.5 x x 100 mm (W x H x D) (2.2 x 4.9 x 3.9 in.) Weight: 550 g (1.2 lbs.) Operating temperature: C ( F) Operating humidity: 20 90% RH, non-condensing Storage temperature: C ( F) Regulatory Approvals EMC: - CISPR22 (EN55022) Class B - EN EN EN EN EN EN EN EN EN ENV50204 Safety: - UL508 - CE/EN60950
7 Model General Power supply: - Input voltage: V AC / V AC by switch or V DC - Output: 120 W, 24 V DC, 5 A Output voltage tolerance: +/- 1% Output rated current: 2 A Output current range: A Ripple and noise: 80 mvp-p Line regulation: +/- 0.5% Load regulation: +/- 1% Efficiency: 84% DC voltage adjust: V Setup, rise and holdup time: ms, 70 ms, 30 ms / 230 V and 115 V Operation Protection Inrush current: cold start at 30 A / 115 V or 60 A / 230 V Leakage current: < 3.5 ma / 240 V AC Withstand voltage: - Between input & output: 3 kv AC - Between input & frame ground: 1.5 kv AC - Between output & frame ground: 0.5 kv AC Isolation resistance: between input & output / input & frame ground / output & frame ground: 500 V DC / 100 Ohms Overload protection: %; type: constant current limiting; reset: auto recovery Over voltage protection: V DC Over temperature protection: 90 C +/- 5 C, power shutdown LEDs DC OK Environmental Dimensions: 65.5 x x 100 mm (W x H x D) (2.5 x 4.9 x 3.9 in.) Weight: 650 g (1.4 lbs.) Operating temperature: C ( F) Operating humidity: 20 90% RH, non-condensing Storage temperature: C ( F) Regulatory Approvals EMC: - CISPR22 (EN55022) Class B - EN EN EN EN EN EN EN EN EN ENV50204 Safety: - UL508 - CE/EN60950
8 INTELLINET NETWORK SOLUTIONS offers a complete line of active and passive networking products. Ask your local computer dealer for more information or visit Copyright INTELLINET NETWORK SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners.
Ripple & Noise (max) (See Note 2) 5V output: 100mVp-p; 12V - 27V outputs: 150mVp-p; 48V output: 200mVp-p
FEATURES 3 Year Warranty 100% Full Load Burn-In Tested Universal AC Input / Full Range Built-In Remote Sense Function Built-In Remote ON/OFF Control Current Sharing up to 2000W (3+1) Forced Air Cooling
More informationgigabit industrial ethernet user manual Models , ,
gigabit industrial ethernet Switch user manual Models 503495, 503532, 503570 Model shown: 503495 INT-503495/503532/503570-UM-0308-01 introduction Thank you for purchasing this INTELLINET NETWORK SOLUTIONS
More informationVP ELECTRONIQUE MASSY - Tel
KEY FEATURES Switching Power Module for PCB Mountable Fully Encapsulated Plastic Case Universal Input Range 90-264VAC, 47-440 Hz Regulated Output Low Ripple and Noise Screw Terminal For Optional CE, UL,
More informationModel No. ( Single Output ) ATC-3.3S ATC-5S ATC-12S ATC-15S ATC-24S Max Output Wattage (W) 10W 10W 10W 10W 10W VAC or VDC
KEY FEATURES Switching Power Module for PCB Mountable Fully Encapsulated Plastic Case Universal Input Range 90-264VAC, 47-440 Hz Regulated Output Low Ripple and Noise Screw Terminal For Optional CE, UL,
More informationVoltage Current Front-mounting bracket
Switching Power Supply S8PS Compact DIN-Rail Mounting Industrial Power Supplies with Capacities Up to 600 W Models range from 0 W to 600 W. Universal input: voltage range 0 to 240 VAC. Power Factor Correction
More informationSeries AME25-JZ 25 Watt AC-DC / DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Series AME-JZ I/O Isolation 000VAC Low Ripple and Noise Operating Temp: -0 C to +70 C Over Voltage Protection Over current Protection Up to
More informationAC-DC POWER SUPPLY UNIVERSAL INPUT, DESK TOP, WATTS MEDICAL APPLICATIONS MUI310-A Series
AC-DC POWER SUPPLY UNIVERSAL INPUT, DESK TOP, 230-310 WATTS MEDICAL APPLICATIONS MUI310-A Series 2MOPP Medical FEATURES Universal Input Range 4000Vac Input/Output Isolation 2 X MOPP Class l Protection
More informationSPECIFICATIONS: PSAK650
FEATURES RoHS Compliant Power OK Signal (Power Good, Logic low) Intelligent LED Indicators Remote On/Off and Remote Sense Function High Efficiency up to 91% Forced Current Sharing at Parallel Operation
More informationPage Housing Plastic Metal Mounting DIN Rail or surface mount Panel or bracket mount Wattage Range 10W to 240W 7.5W to 240W 10W to 300W
Selection Guide Selection Guide PS5R Slim Line PS5R PS3L Operator Interfaces Communication & Networking PLCs NEW Models Appearance Automation Software Page 107 113 118 Housing Plastic Metal Mounting DIN
More informationChrome DIN Rail Power Supply 12V 9.96W 1 Phase (Class II & NEC Class 2) / DRC-12V10W1A
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More information12-15VDC (12V±5%) 24-28VDC (24V±5%)
Features Description Universal AC input (85-264VAC) Long 7 year warranty Protections: SCP, OVP, OCP, OTP 1% full load burn-in test DC OK indicator LED with relay contacts cooling by free air convection,
More informationSPECIFICATIONS. Input Output Agency Approvals 0 ~ 62.5A. toll-free (603)
Technical Data Sheet 750 Watt, 12 Volt, Single Output Power Supply With PFC, Voltage & Current Trim Functions UNIT CODE PS-RSP 750-12 DESCRIPTION 750 Watt 12 Volt, Single Output Power Supply with PFC plus
More informationAPM-40 SERIES FEATURES PRODUCT OVERVIEW. Model Selection Guide. Input Specifications. AC/DC Power Module 40W, Industrial & Medical Safety
FEATURES Fully encapsulated Plastic Case 3 Mounting Versions: - PCB Mounting with Solder Pins - Chassis Mounting with Screw Terminals - DIN-Rail Mounting Package Dimension 88.9x63.5x30.0 mm (PCB Version)
More informationConstant Voltage Mode
FEATURES: AC Input 1~277VAC Built-in Active PFC Function Protection: SCP / OVP / OTP Flicker Free High Operating Ambient Temp.: -3 ~+6 Surge protection: L-N 4KV, L-FG/N-FG 8KV Safety: UL 875 / PSE EMI:
More information3000W Programmable Single Output AEK AEK AEK AEK
000W Programmable Single Output Features: Universal AC input / Full range Programmable output Voltage (0% ~ 05%) Programmable output Current (0% ~ 05%) High power density 6.W / inch³ Forced current sharing
More informationKUANTECH (SHEN ZHEN) COMPANY LIMITED KSAFD W1UK
1 GENERAL... 2 1.1 Description... 2 2 INPUT REQUIREMENTS... 2 2.1 Input Conditions... 2 2.2 AC Inrush Current... 2 3 OUTPUT REQUIREMENTS... 2 4 MECHANICAL... 3 4.1 Enclosure And Layout... 3 4.2 Input and
More informationSeries AMEL10-MJZ 10 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com Models Single output Model Input Voltage (VAC/Hz) FEATURES: Input Voltage (VDC) Max Output wattage (W) Output Voltage (V) Output Current max (A) Maximum
More informationChrome DIN Rail Power Supply 5V 7.5W 1 Phase (Class II & NEC Class 2) / DRC-5V10W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationDVI KVM Switch user manual Model
DVI KVM Switch user manual Model 156066 INT-156066-UM-0808-01 introduction Thank you for purchasing the INTELLINET NETWORK SOLUTIONS DVI KVM Switch, Model 156066. This convenient device lets you control
More informationDDR-120 series. 120W DIN Rail Type DC-DC Converter
is a DIN Rail type DC-DC converter with main features including DIN rail-type easy installation, : SPECIFICATION MODEL OUTPUT INPUT PROTECTION OTHERS NOTE DDR-120A-12 DDR-120A-24 DC VOLTAGE RATED CURRENT
More informationSeries AME60-MJZ 60 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com Models Single output Model Input Voltage (VAC/Hz) FEATURES: I/O Isolation VAC Continuous Short circuit protection Input under-voltage protection Low
More informationPower Supply. Users Guide PRODUCT MANUAL. WESTELL.COM Westell Technologies MNL rd
PRODUCT MANUAL Power Supply Westell Technologies. 960-1152-MNL rd DISCLAIMER All information and statements contained herein are accurate to the best of Westell Technologies knowledge. Westell Technologies
More informationRTU500 series Data Sheet Power Supply CP-E 24/2.5
Data Sheet Power Supply CP-E 24/2.5 Power Supply CP-E 24/2.5 Application The primary switch mode power supply offers two voltage input ranges. This enables the supply with AC or DC. Furthermore it is equipped
More information12-15VDC (12V±5%) 24-28VDC (24V±5%)
Features DIN Rail Description Universal AC input (85-264VAC) Long 7 year warranty Protections: SCP, OVP, OCP, OTP 1% full load burn-in test DC OK indicator LED with relay contacts cooling by free air convection,
More information< 50 A max. (115 VAC) / < 70 A max. (230 VAC)
KEY FEATURES U Bracket Switching Power Supply Universal Input: 90-264 VAC Active P.F.C. Function, PF>0.95 300W Convection without FAN 480W Convection with 18CFM FAN Protections: Over Load / Over Voltage
More informationOutput Current Input Current Max. capacitive Load
AB4S/D Series AC/DC Power Module 4W, Industrial & Medical Safety FEATURES Fully encapsulated Plastic Case 3 Mounting Versions: - PCB Mounting with Solder Pins - Chassis Mounting with Screw Terminals -
More informationINJ-24A Series Quick Installation Guide
INJ-24A Series Quick Installation Guide Moxa High-Power PoE+ Injector Edition 4.1, August 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777
More informationSeries AME10-VZ 10 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com FEATURES: Picture Coming Soon I/O Isolation 000VAC Continuous Short circuit protection Operating Temp: -0 C to + C Energy Star compliant Input: -VAC,
More informationSeries AME5-CJZ 5 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com FEATURES: I/O Isolation 000V Continuous Short circuit protection Operating Temp: -2 C to 0 C Energy Star compliant Input: -26V, -6Hz, or 20-0VDC pact
More informationChrome DIN Rail Power Supply 24V 10W 1 Phase (Class II & NEC Class 2) / DRC-24V10W1A
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationElectrical Specification for: efo Wide range AC/DC Single 12V Output 400W Power Supply Telkoor Part Number: CUSTOMER SIZE CAGE CO
Electrical Specification for: efo400-112 Wide range AC/DC Single 12V Output 400W Power Supply Telkoor Part Number: 900-4136-0000 GENERAL SCALE RELEASE DATE PRELIMINARY SHEET 1 OF 5 REVISION HISTORY Rev
More informationSPECIFICATIONS. Input Output Agency Approvals 0 ~ 100A
Technical Data Sheet 50 Watt, 5 Volt, Single Output Power Supply With PFC, Voltage & Current Trim Functions UNIT CODE -PFC 50-5 DESCRIPTION 50 Watt 5 Volt, Single Output Power Supply with PFC plus Voltage
More informationDDR-120 series. 120W DIN Rail Type DC-DC Converter
DIN Rail Type DC-DC Converter + is a DIN Rail type DC-DC converter with main features including DIN rail-type easy installation, : DIN Rail Type DC-DC Converter SPECIFICATION MODEL OUTPUT INPUT PROTECTION
More informationSwitch Mode Power Supply S8VT 120/240/480/960 W Models
Switch Mode Power Supply 120/240/480/960 W Models Natural Cooling Three-phase Power Supply Range from 5A up to 40A with Output Voltage of 24VDC 3 phase 400 to 500 VAC 5, 10, 20 and 40 A; 24 VDC output
More informationChrome Class II DIN Rail Power Supply 24V 10W 1 Phase (NEC Class 2 & Household) / DRC-24V10W1HZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Household appliance approvals IEC/EN 60335-1 4kV Electrical Fast Transient / Burst Universal AC input voltage
More informationStandards VDE: EN60950; UL1950; C-UL: CSA C22.2 No.234; IEC950; VDE0805
AC/DC Power Supply Multi-output Wide range input for world-wide use (85 264 Vac). This series is a 3ch output model. Features Wide input voltage range: 85-264Vac 110-370Vdc High efficiency & reliability
More informationOutput Voltage* (nom.)(adjustable)
Industrial Power Supplies TBLC Series, 6 90 W Low profile case, module depth only 55 mm Suitable for mounting in domestic installation panels Very high efficiency and low standby power -> compliance to
More informationAC-DC POWER SUPPLIES UNIVERSAL INPUT, 65 WATT MEDICAL APPLICATIONS MUI65 SERIES
AC-DC POWER SUPPLIES UNIVERSAL INPUT, 65 WATT MEDICAL APPLICATIONS 2MOPP Medical FEATURES Universal Input Range Operating Temperature Range: -25º to 80ºC (with derating) Compact Package: 2.00 3.00 1.16
More informationOrdering Information. Three-phase Input Switch Mode Power Supply S8VT S8VT. Model Number Legend
Three-phase Input Switch Mode Power Supply S8VT DIN-rail mounting, Power Supply with a range of 5 A to 40 A output current 3 phase 400 to 500 VAC 5, 10, 20 and 40 A; 24 VDC output Higher stability, lower
More informationChrome DIN Rail Power Supply 24V 30W 1 Phase (Class II & NEC Class 2) / DRC-24V30W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationVER05 Series. xxx Series. 5 Watt. AC-DC Power Supplies. Models & Ratings. Input. Output
5 Watt xxx Series Energy Efficiency Level VI Barrel Jack & USB Versions Interchangeable Mains Connectors Included Universal Input Output Voltages from 5.0 V to 12.0 V Class II Construction Low Cost B R
More informationefo Series Wide range AC/DC Single Output 1000W Rugged Power Supply Electrical Specification for: Telkoor Part Number:
Electrical Specification for: efo1000-124 Series Wide range AC/DC Single Output 1000W Rugged Power Supply Telkoor Part Number: 900-1124-1000 GENERAL SCALE RELEASE DATE 05/08/2012 SHEET 1 OF 6 Rev Level
More informationSPECIFICATIONS. Input Output Agency Approvals
Technical Data Sheet 1,500 Watt 12 Volt, Single Output Power Supply with PFC and Parallel Functions UNIT CODE PS-RSP 1500-12 DESCRIPTION 1,500 Watt, 12V, Single Output Power Supply with PFC and Parallel
More informationChrome DIN Rail Power Supply 24V 10W 1 Phase (Class II & NEC Class 2) / DRC-24V10W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage without power de-rating Efficiency > 80.0% @ 115Vac & 230Vac NEC Class 2 / Limited
More informationSwitching Power Supply S82J. Ordering Information. Open-Frame, Covered-Frame, or Enclosed-Frame Type with Capacity Up to 600 W
Switching Power Supply Open-Frame, Covered-Frame, or Enclosed-Frame Type with Capacity Up to 600 W Models range from 10 to 600 W UL 508 approval on 100-W 150-W, 300-W, and 600-W models Wide range of output
More informationTEP 100WIR Series, 100 Watt
TEP 100WIR Series, 100 Watt Features Compact metal package Ultra wide 4:1 input voltage ranges 8.5 36, 16.5 75, 43 160 VDC EN 50155 approval for railway applications Very high efficiency up to 92% No minimum
More informationAC/DC Power Supply Single Output
AC/DC Power Supply Single Output Open frame type power supply with AC input range 85-132 (-SA) and 170-264V (-SB). Simplified circuit design provides high cost effectiveness. Features Wide input voltage
More informationStandards VDE: EN60950; UL1950; C-UL: CSA C22.2 No.234; IEC950; VDE0805
AC/DC Power Supply Multi-Output Wide range input for world-wide use (85 264 Vac). This series is a 2ch output model. Features Wide input voltage range: 85-264Vac 110-370Vdc High efficiency & reliability
More informationSnaptec Australia Pty. Ltd.
KEY FEATURES Universal Input: 90-264 VAC With P.F.C. Function, PF>0.95 Remote ON/OFF Function Current Share Function Power Good Function High Efficiency up to 90~93% Protections: Over Load / Over Voltage
More informationHigh Efficiency. LED Status Indicator. IPX1 Rated. CEC Compliant
FWA180 Series 180 Watts ITE Desktop Power Supply High Efficiency High Power Density 5.9W/in3 5 Year Limited Warranty LED Status Indicator IPX1 Rated Hold up Time > 25ms at full load ITE Approval EN609501
More informationOver voltage protection: Output shutdown (V1 only) Weight: 730g
AC/DC Power Supply Multi-Output Wide range input for world-wide use (85 264 Vac). This series is a 2ch output model. Features Wide input voltage range: 85-264Vac 220-370Vdc High efficiency & reliability
More informationIndustrial Slim Type Fast Ethernet Rail Switch
Industrial Slim Type Fast Ethernet Rail Switch Version 1.0 May, 2008. Table of Content Overview...2 1.1 About the 505710 / 505628 unmanaged Industrial Switch...2 1.2 Hardware Features...2 Hardware Installation...3
More informationSPECIFICATIONS. Input Output Approvals
Technical Data Sheet,000 Watt Volt, Single Output Power Supply with PFC and Parallel Functions UNIT CODE PS-RSP 000- DESCRIPTION,000 Watt, V, Single Output, Enclosed Power Supply with PFC and Parallel
More informationPower Supplies. PS5R Standard Series Switching Power Supplies. Part Numbers. Part Number
Standard Series Key features: Wide power range: 7.W-24W Universal input : 7.W-W: 8-264V AC/1-37V DC 1W: 8-2V AC/17-264V AC 24-37V DC (selectable) W, W, 24W: 8-264V AC/11-3V DC Overcurrent/overvoltage protection
More information12W AC/DC interchangeable Adapter MU012-HA Series
FEATURES Universal input Voltage: 90-264VAC, 50/60Hz DoE Level VI efficiency Over voltage, Over current, Short circuit protection Fully enclosed plastic case AC plug interchangeable Small wall-mounted
More informationCompactPCI SYSTEM POWER SUPPLIES. CPCI SERIES 150 to 350 Watts, Ac Input with PFC DPCI SERIES 150 to 350 Watts, 48 Vdc Input FEATURES:
CPCI SERIES 150 to 350 Watts, Ac Input with PFC DPCI SERIES 150 to 350 Watts, 48 Vdc Input FEATURES: EXECUTIVE MEMBER 150 W and 200 W in 3U x 8HP, 350 W in 6U x 8HP Fully compliant with PICMG CompactPCI
More informationCliQ DIN Rail Power Supply 24V 60W 1 Phase / DRP024V060W1AZ
7 Highlights & Features Universal AC input range Power will not de-rate for the entire input voltage range Power Boost of 150% for 3 seconds Rugged and compact design (Vibration 5G, Shock 30G) Wide operating
More informationFWA180 Series 220 Watts ITE Desktop Power Supply
Page 1 of 7 FWA180 Series 220 Watts ITE Desktop Power Supply High Efficiency High Power Density 5.9W/in3 5-Year Limited Warranty LED Status Indicator IPX1 Rated Hold-up Time > 25ms at full load ITE Approval
More information5W AC/DC interchangeable Adapter MU005-HA Series
FEATURES Universal input Voltage: 90-264VAC, 50/60Hz DoE Level VI efficiency Over voltage, Over current, Short circuit protection Fully enclosed plastic case AC plug interchangeable Small wall-mounted
More informationOutput Voltage* (nom.)(adjustable)
Industrial Power Supplies TBLC Series, 6 90 W Low profile case, module depth only 59,5mm Suitable for mounting in domestic installation panels Low output ripples and spikes Fully compliance to ECO-Standard
More informationArticle No. 6GK59230PS003AA2 6GK59240PS001AA2 Product Name. Power Supply SCALANCE PS924 PoE Input: 120/230V AC; Output: 54V/ 1.
Product Name Type of power supply Electrical data Input Waveform of the input Supply Power Supply SCALANCE PS924 PoE Input: 120/230V AC; Output: 54V/ 1.6A DC; NEC Class 2 single-phase AC Power Supply SCALANCE
More informationMPU-120S Series. Single Output, 180W Compact, U-Channel AC/DC Power Supplies. Key Features:
MPU-120S Series Single, 180W Compact, U-Channel AC/DC Power Supplies Key Features: 180W Power Universal 90-264 AC Power Factor Correction EN 60950 Approved Compact U-Channel Five Single Models Meets EN
More informationTEP160-WIRCM SERIES 160 Watt High Density Brick DC-DC Converter Measures: 2.40 x 2.28 x 0.50
Features Compact metal package Ultra wide 4:1 input voltage ranges 8.5 36, 16.5 75, 43 160 VDC EN 50155 approval for railway applications Very high efficiency up to 91% No minimum load Soft start Ajustable
More informationCPCI - 6U - DC - 350W
Electrical Specification for: CPCI - 6U - DC - 350W Telkoor Part Number: 900-6001-0000 Approvals Name Date Written by: S. Sadot 13/3/08 Engineering: M. Heller 13/3/08 Sales & Marketing: B. Steinfeld 13/3/08
More informationECF40 Series. 40 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details
40 Watts 40 W Convection Rating 1.5 by 3 Footprint Low 1.1 Profile High Efficiency Medical and ITE pprovals High Power Density Less than 0.15 W No Load Input Power 3 Year Warranty The ECF40 series is designed
More informationDPS240/12V Dimmable Power Supply Custom LitePad
Rosco s DPS240/12V Dimmable Power Supply is designed to complement larger Custom LitePad installations. The system comes with power supply and controller all pre-wired and ready to integrate with an array
More informationFeatures : High efficiency up to
Bauart gepruft S icherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 5000W Single Output Power Supply Forced air cooling by built-in DC with fan speed control fail Output voltage can be trimmed
More informationChrome DIN Rail Power Supply 24V 60W 1 Phase (Class II & NEC Class 2) / DRC-24V60W1A
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationPART NUMBER STRUCTURE. P-DUKE Technology Co., Ltd Page 1
Medical Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger PV Railway PART NUMBER STRUCTURE M A F 150 U S 12 B - Application Package Dimension Output Input Output Output Protection
More informationDALI Bus Power Supply. DLP- 04 series VAC
0 05 VAC Ⅱ,. { File Name: DLP-0-SPEC 08-08-6 SPECIFICATION MODEL DLP-0R DLP-0L OUTPUT RATED POWER SETUP, RISE TIME HOLD UP TIME (Typ.) 70ms/0VAC 6ms/5VAC at full load VOLTAGE RANGE 90 ~ 6VAC 0 ~ 70VDC
More informationWatts. xppower.com. General. Input. Environmental. EMC & Safety. Output. IT & Medical Approvals. Energy Efficiency Level V, CEC2008 & EISA 2007
AC-DC 85-50 Watts AHM Series IT & Medical Approvals xppower.com Energy Efficiency Level V, CEC008 & EISA 007
More informationOver voltage protection: Output shutdown Weight: 73g
AC/DC Power Supply Single Output The BW-series is an open frame board with an optional cover. Simplified circuit design enabled cost optimisation and miniaturization. Safety design is applied to UL, CUL
More informationSPECIFICATIONS. AC Input DC Output Approvals Universal AC input 85 ~ 264V 0 ~ 27A
Technical Data Sheet 648 Watt, 4 Volt, Medical Safety Certified Single Output Power Supply with PFC UNIT CODE MED-PS 600-4V DESCRIPTION 66 Watt, 4 Volt, Single Output, MOOP Level Medical Power Supply with
More informationSTEADYTEC Light Duty RJ45 Plug STX IP20 Light Duty RJ45 plug Cat.6, AWG22-26, Telegartner
STEADYTEC Light Duty RJ45 Plug STX IP20 Light Duty RJ45 plug Cat.6, AWG22-26, Telegartner Light Duty Field RJ-45 Plug Solid upper clip makes closely connection to the patch panels AWG22-26 CAT5E/CAT6 accepted
More informationVEL05 Series. xxx Series. 5 Watt. AC-DC Power Supplies. Models & Ratings. Input
5 Watt xxx Series Energy Efficiency Level VI Barrel Jack & USB Versions Fixed Mains Connectors Universal Input Output Voltages from 5.0 V to 12.0 V Class II Construction Low Cost B R A N D The VEL05 series
More informationCPCI - 6U - AC - 600W
Electrical Specification for: CPCI - 6U - AC - 600W Telkoor Part Number: 900-6115-0000 SCALE RELEASE DATE 13/12/08 SHEET 1 OF 7 REVISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective
More informationPower supply CP-E 48/1.25 Primary switch mode power supply
Data sheet Power supply CP-E 48/1.25 Primary switch mode power supply The CP-E range offers enhanced functionality while the number of different types has been considerably reduced. Now all power supply
More informationOutput Amps Model Number Output Voltage (max), (Note 2) Load Reg (max) Ripple & Noise pk-pk Efficiency typ.
Universal 90-264VAC Input High Efficiency Improved EMI Performance 3000VAC Isolation Single, Dual and Triple Outputs Full Safety Approvals As Small as 2.36 W x 3.41 L x 0.93 H (Single Output) Output Amps
More information750W Power Supply with Single Output. RSP-750 series. File Name:RSP-750-SPEC
750W Power Supply with Single Output File Name:RSP-750-SPEC 06-0-7 750W Power Supply with Single Output SPECIFICATION MODEL OUTPUT INPUT PROTECTION FUNCTION ENVIRONMENT SAFETY & EMC (Note 4) OTHERS NOTE
More informationPART NUMBER STRUCTURE. P-DUKE Technology Co., Ltd Page 1
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE T A H 450 U S 12 - F2 Application Package Dimension Output Input Output Output Protection
More informationSPECIFICATION M/N: MPD-F For SWITCHING POWER SUPPLY. Revision History
SPECIFICTION For SWITCHING POWER SUPPLY M/N: MPD-F3- Revision History REV. Jan. 7 th 200 REV. Mar. 4 th 200 REV. Mar. 7 th 200 REV. Mar. 28 th 20 REV. Nov. 25 th 20 REV. Jul. 5 th 202 REV. Jun. 4 th 203
More informationSeries AM1M-NZ 1 Watt DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Input Low Profile DIP case 1.5 and 3K V I/O Isolation Continuous Short circuit protection Max Input Current Full/No
More informationSafety Standards. Model Number:
PMC Highlights & Features Universal AC input range from 85Vac to 264Vac without power de-rating High operating ambient temperature, > 60 o C de-rating power High MTBF > 700,000 hrs. as per Telcordia SR-332
More informationREVISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective Approved By A 13/12/08 Specification Release 13/12/08 S. Sadot A1 13/02/09
Electrical Specification for: CPCI - 6U - DC - 600W Telkoor Part Number: 900-6113-0000 SCALE RELEASE DATE 13/12/08 SHEET 1 OF 7 REVISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective
More informationEnvironmental. Electrical Specifications at 25 O C E Output Constant Current
12 Watt - Model: Environmental Drive Mode: Constant Current or Constant Voltage Technology: PFC Off-Line Switch Mode : Max. Input Voltage: 120 to 277VAC, 47-63Hz Number of Outputs: One Output Voltages:
More informationMPO-120S Series. Single Output, 180W Compact, Open Frame AC/DC Power Supplies. Key Features:
MPO-120S Series Single, 180W Compact, Open Frame AC/DC Power Supplies Key Features: 180W Power Universal 90-264 AC Power Factor Correction EN 60950 Approved High Efficiency Five Single Models Meets EN
More information500Watts Medical Single Output
FEATURES Medical 60601-1 3 rd Edition approved U-Channel, End fan and Top fan types available Optional high efficiency OR-ing FET diode Current share function 2 year warranty ELECTRICAL SPECIFICATIONS
More informationEnvironmental. Electrical Specifications at 25 O C E Output Constant Current
17 Watt - LD Series LD Series Model: LD Series Environmental Drive Mode: Constant Current or Constant Voltage Technology: PFC Off-Line Switch Mode : Max. Input Voltage: 100 to 277VAC, 47-63Hz Number of
More informationMODEL: M5DY SEN TRONIC AG CURRENT LOOP SUPPLY. [2] POWER INPUT AC Power M: V AC (Operational voltage range V, Hz)
Super-mini Terminal Block Signal Conditioners M5-UNIT CURRENT LOOP SUPPLY Functions & Features Powering a 0 ma DC current loop Applicable to smart transmitters Isolation between the input and output Fast
More informationPART NUMBER STRUCTURE. P-DUKE Technology Co., Ltd Page 1
Medical Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger PV Railway PART NUMBER STRUCTURE M A H 450 U S 12 - F2 Application Package Dimension Output Input Output Output Protection
More informationPS5R Series Switching Power Supplies. The PS5R offers a sleek, compact, ergonomic design, worldwide approvals, and broad range of output capacities.
Switching Power Supplies The offers a sleek, compact, ergonomic design, worldwide approvals, and broad range of output capacities. With U 508 isting, additional savings in space and cost can be realized
More informationR S T-5000 s e ri es. 5000W Single Output Power Supply. Applications. Features
R S T-5000 s e ri es Bauar t ge pru ft Sicherheit eg elma ge od o s be wac g www. tuv.com ID 2000000000 Features 3 ψ 3-wire / 196~305VAC or 3 ψ 4-wire / Y 340~530VAC wide input range Built-in active PFC
More informationPower Supplies GLX40 GLX50 GLX60 GLX110-B GLX110-C GLX120 GLX140-C GLX140-CF GLX150-C GLX17Q-C GLX17S-C GLX200 GLX250-CEF GLX250-CF
3 Power Supplies GL Series: Single & Multi Output Switchers The new GL series provides a broad range of AC/DC power supply solutions that covers power ratings from 25 watts to 500 watts for use in various
More informationFirst of all, thank you for purchasing R2W series redundant power supply.
1.1 INTRODUCTION First of all, thank you for purchasing R2W series redundant power supply. The R2W series is a 1+1 hot-swappable / hot-pluggable redundant power supply. It consists of, 1) complete metal
More informationMOXA EtherDevice Switch EDS-205 Hardware Installation Guide
MOXA EtherDevice Switch EDS-205 Hardware Installation Guide 1 st Edition, May 2004 EDS-205 Installation Instructions TG200838 issue 1/A 09/12/04 Overview The MOXA EtherDevice Switches, EDS-205 series,
More informationChrome DIN Rail Power Supply 12V 25W 1 Phase (Class II & NEC Class 2) / DRC-12V30W1A
Highlights & Features Class II, Double Isolation (No Earth connection is required) Universal AC input voltage range and full power up to 55 C Power will not de-rate for the entire input voltage range Efficiency
More informationSAM Listed LED Optimized Drivers. Environmental. Electrical Specifications at 25 O C E Output Current. Voltage Accuracy
Model: LD40W480 UL SAM Series Drive Mode: Constant Voltage Technology: PFC Off-Line Switch Mode Power: 40W Max. Voltages: 1VDC or 4VDC Currents: 418mA - 3330mA Environmental 1. Operating temperature: Tc
More informationTTX400-3U-1S Watt, 3U, 1 Slot, 24VDC Input, CompactPCI Power Supply. CompactPCI POWER SUPPLY
350 Watt, 3U, Slot, 4VDC Input, CompactPCI Power Supply The TTX Series from Tracewell Power offers a wide variety of form factors, utilizing a new topology which provides excellent power density and efficiency.
More informationVEL05 Series. xxx Series. 5 Watt. AC-DC Power Supplies. Models & Ratings. Input
5 Watt xxx Series Energy Efficiency Level VI Barrel Jack & USB Versions Fixed Mains Connectors Universal Input Output Voltages from 5.0 V to 12.0 V Class II Construction Low Cost BRAND The VEL05 series
More information3.3V & 5V max 150W, total output max 300W
SDX-300-24 300W, 24V Input DC-DC for ATX System 150 x 1 x 86 mm 5.90 x 5.51 x 3.39 inch Features: * Input and output isolation * Soft start function, low inrush current * Input over voltage and under voltage
More information