Light Industrial Unmanaged Ethernet Switches. Unmanaged. Technical Details

Transcription

1 SL Unmanaged The SL series Industrial Unmanaged Ethernet es provide advanced performance that enables you to achieve real-time deterministic operation. These ruggedized switches are hardened to provide superior reliability. They require no user setup and immediately start operating as soon as you power them up. Sixnet switches are designed to make your job easier, ensuring your system will keep running for many years to come. Technical Details Type Ethernet isolation Flow control MAC addresses 1024 Memory bandwidth Typical latency Functions Speed MDI / MDIX Polarity Speed Duplex-operation Devices Standards Power input voltage Unmanaged 1500 Vrms 1 minute Full duplex operation 3,2 Gbit/s General data 5 μs at 100 Mbps (plus frame time) 16 μs at 10 Mbps (plus frame time) Store & forward, wire-speed switching, non-blocking, Ethernet ports Auto-negotiation for 10 or 100 Mbps Auto- MDI/MDIX-crossover for either cable type Auto-polarity corrects for crossed +/- signals Fiber ports (if existing) 100 BaseFX (100 Mbps) Full duplex Ethernet compliance IEEE Ethernet supports legacy devices All IEEE standards supported Power input Transient protection: 15,000 watts peak Protection Spike protection: 5,000 watts (10 times for 10 μs) Environmental Storage temperature -40 ~ +85 C Humidity 5 to 95% RH (non-condensing) Vibration and shock IEC bis 6, -27 und -32 1

2 Technical Details Electrical safety EMC Standards compliance UL508/CSA C22.2/14; EN , CE FCC part 15, ICES-003, EN55022, EN , CE MTBF >1,000,000 hours typical per MIL-HDBK-217F2 Ground Benign at 35 C Hazardous locations Maritime RoHS and WEEE Packaging Mounting Protection class IP 30 Type 1 Type 2 Warranty UL1604/CSA C22.2/213 (Class I, Div. 2); EN (Zone 2, Category 3), CE (ATEX) Rated for marine & offshore per ABS RoHS (Pb free) and WEEE compliant Mechanical Lexan plastic (UL94V0) Slim-Style for Din-rail or direct panel mounting 107 x 25 x 95 mm, 110 g 107 x 38 x 95 mm, 170 g Warranty 5 years on design and manufacturing defects Ordering guide SL series (total) 10/100 Ethernet 100 Fiber Type Connector Operating range Operating temperature range SL-5ES watts -10 ~ +60 C 1 SL-5ES-2SC Multimode SC 4 km 3 watts -10 ~ +60 C 1 SL-5ES-2ST Multimode ST 4 km 3 watts -10 ~ +60 C 1 SL-5ES-3SC Singlemode SC 20 km 3 watts -10 ~ +60 C 1 SL-5ES-3ST Singlemode ST 20 km 3 watts -10 ~ +60 C 1 SL-5ES-3SCL Singlemode SC 40+ km 3 watts -10 ~ +60 C 1 SL-5ES-3STL Singlemode ST 40+ km 3 watts -10 ~ +60 C 1 SL-6ES-4SC Multimode SC 4 km 5 watts -40 ~ +60 C 2 SL-6ES-4ST Multimode ST 4 km 5 watts -40 ~ +60 C 2 SL-6ES-5SC Singlemode SC 20 km 5 watts -40 ~ +60 C 2 SL-6ES-5ST Singlemode ST 20 km 5 watts -40 ~ +60 C 2 SL-6ES-5SCL Singlemode SC 40+ km 5 watts -40 ~ +60 C 2 SL-6ES-5STL Singlemode ST 40+ km 5 watts -40 ~ +60 C 2 SL-8ES watts -40 ~ +60 C 2 SL-9ES-2SC Multimode SC 4 km 5 watts -40 ~ +60 C 2 SL-9ES-2ST Multimode ST 4 km 5 watts -40 ~ +60 C 2 SL-9ES-3SC Singlemode SC 20 km 5 watts -40 ~ +60 C 2 SL-9ES-3ST Singlemode ST 20 km 5 watts -40 ~ +60 C 2 SL-9ES-3SCL Singlemode SC 40+ km 5 watts -40 ~ +60 C 2 SL-9ES-3STL Singlemode ST 40+ km 5 watts -40 ~ +60 C 2 Power consumption Packaging type 2

3 Accessories - power supply Model AD F AD FS AD F Power input 24 V DC 24 V DC 24 V DC Output current 1 A (24 W) 2 A (48 W) 5 A (120 W) Input current 100 ~ 240 V AC 100 ~ 240 V AC 100 ~ 240 V AC SL-5/8/9ES connectors Single DC Supply Dual DC Supplies Chassis GND (panel) Chassis GND (panel) Front of (connectors) P2 P1 P2 P1 Back of (DIN rail) Single DC Power Redundant DC Power SL-6ES connectors Single DC Supply Dual DC Supplies Alarm Output Load (opt.) Alarm Output Load (opt.) Front of (connectors) P2 P1 OK Chassis GND is made through the DIN rail mounting P2 P1 OK Back of (DIN rail) Single DC Power Redundant DC Power 3

4 Mounting 1 2 Recommended DIN rail mounting steps: 1. Hook the top back of the DIN rail clip on the unit over the din rail. 2. Push the bottom of the unit towards the DIN rail until it snaps into place. Removal B A Recommended DIN rail removal steps: A. Push the whole unit down to free the bottom of the DIN rail clip. B. Pull the bottom of the unit away from the DIN rail, unhook the top of unit and remove it from the DIN rail. 4

5 `Dimensions (cm) Removable Screw Block 0.40" (1.02 cm) Typical for SC or ST fiber 2.90" [7.35 cm] Snaps to standard DIN rail EN50022 (35 mm) 2/3/5 6/8/9 1.01" [2.57 cm] 1.98" [5.02 cm] 3.95" [10.03 cm] 4.20" [10.67 cm] Dia. 0.15" (0.38 cm) Use for direct panel mounting to a flat surface 1.98" [5.02 cm] 1.01" [2.57 cm] 1.00" [2.54 cm] 1.50" [3.81 cm] Packaging type 1 Packaging type " [8.28 cm] 0.06" [0.15 cm] Zum Hagenbach 7 D Laer info@welotec.com Fon: +49 (0)2554/ Fax: +49 (0)2554/ WEL-SL-unmanaged-V1-EN ed. 05/12 Welotec GmbH Welotec is using a ISO 9001:2008 certified quality management system All specifications are subject to change 5