General Specifications

Transcription

1 Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators eneral Specifications lectrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): Logic/Power Level (gold over silver): Other V C 0V 0V DC for 0V DC for all other circuits 0.V 8V C/DC maximum (pplicable Range 0.m ~ 0mV ~ 8V) Combines silver & gold ratings Note: ind additional explanation of dual rating & operating range in Supplement section. Contact Resistance: 0 milliohms maximum for silver; 0 milliohms maximum for gold Insulation Resistance:,000 megohms 00V DC Dielectric Strength:,000V C minimum between contacts for minute minimum;,00v C minimum between contacts and case for minute minimum Mechanical Life: 0,000 operations minimum lectrical Life:,000 operations minimum for silver; 0,000 operations minimum for gold; 0,000 operations minimum for silver V C ngle of Throw: Materials & inishes ctuator Clip & Mounting rame: Stainless Steel ody rame: Stainless steel Case: Diallyl phthalate resin (UL9V 0) Movable Contactor: Phosphor bronze with silver or gold plating Movable Contacts: Silver alloy (code W); copper with gold plating (code ); or silver alloy with gold plating (code ) Stationary Contacts: Silver with silver plating (code W); copper or brass with gold plating (code ); or silver with gold plating (code ) Terminals: Copper or brass with silver plating; or copper or brass with gold plating nvironmental Data Processing Operating Temp Range: Humidity: Vibration: Shock: Soldering: Cleaning: Standards & Certifications 0 C through +8 C ( through +8 ) 90 ~ 9% humidity for 9 0 C (0 ) 0 ~ Hz with peak-to-peak amplitude of.mm traversing the frequency range & returning in minute; right angled directions for hours 0 (90m/s ) acceleration (tested in right angled directions, with shocks in each direction) Wave Soldering (PC version) for old: See Profile in Supplement section. Manual Soldering for old: See Profile in Supplement section. Wave Soldering (PC version) for Silver: See Profile in Supplement section. Manual Soldering for Silver: See Profile in Supplement section. Note: ctuator must be in (center) position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution. lammability Standards: UL9V 0 for case UL: ile No. - Recognized only when ordered with marking on switch. dd /U or /CUL before first dash in part number to order UL recognized switch. ll models recognized V 0V C or 0.V 8V DC maximum. CS: ile No. 0_0_000 - Certified only when ordered with marking on switch. dd /C before first dash in part number to order CS certified switch. ll models certified V C 0V C or 0.V 8V maximum. //7

2 Miniature Rockers Series M Distinctive Characteristics Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PC. High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. The molded diallyl phthalate case has a UL 9V-0 flammability rating. poxy sealed terminals prevent entry of solder flux and other contaminants. Prominent external insulating barriers increase insulation resistance and dielectric strength. ias guard prevents misalignment of contacts; interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Clinching of the frame to the case well above the base and terminals provides,00v dielectric strength. ctual Size Snap-in Mount racket PC Mount lat rame Mount Page Page 7 Page 8 Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles

3 Snap-In Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators M0 Poles SPDT DPDT SPT Circuits N N () 8 () () 9 () * * () () * 7 () ( ) = Momentary * - circuits Mounting rame TJ Snap-in rame W Red.0 (.mm) SPDT -N- Circuit Solder Lug Terminals Terminals 0 Solder Lug 0 Quick Connect (.mm) Straight PC. (0.8mm) Wirewrap.70 (9.0mm) Wirewrap.9 (.mm) Wirewrap.0 (7.0mm) Wirewrap Contact Materials & Ratings Silver; V C 0V C old; Rated 0.V 8V C/DC max old over Silver; V C & 0.V 8V C/DC max S Rockers & Paddles TYPICL SWITCH TJ W 0 C DSCRIPTI OR TYPICL ORDRIN XMPL M0TJW0-C-.0 (.mm).0 (.mm) Wide Paddle. (.mm) alse Illluminated Rocker in lack only Rocker & Paddle Colors C H Snap-in rame Silver Contacts with mp Rating lack White Red Yellow reen lue ray lack ezel without LD

4 Snap-In Mount Miniature Rockers Series M ORDRIN XMPL Optional ezels ezel without LD Snap-in rame SPDT -N- Circuit H DSCRIPTI OR TYPICL ORDRIN XMPL Silver Contacts with mp Rating Solder Lug Terminals ezel Colors lack White Yellow reen lue ray ezel with Round LD lack ezel with Round LDs ezel with Rectangular LDs IMPORTNT: lack Switches are supplied without UL, culus & CS marking unless specified. UL, culus & CS recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the eneral Specifications page. Red.0 (.mm) M0TJW0-C--C C Red reen Top LD LD Colors LD LDs Top LD Red ottom LD reen lack ezel with Round LDs ottom LD C Red C Red Yellow Yellow reen reen Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles

5 Snap-In Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators Pole SP DP or Throw (-On) Connected Terminals & Schematic Pole Model Down Center Up Connection SP TJ (8.0).70 W Model M0 M0 M0 M08 M09 M0 M0 M07 Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics Down Center Up Down Center Up () () N N () () () M0 N M0 M0 N () M08 () () M09 () Snap-in rame (.).80 POLS & CIRCUITS - OPN OPN - - () () MOUNTIN RM Note: Terminal numbers are not actually on the switch. SPDT DPDT The SPT model utilizes a double pole base. connection must be made during field installation. Conn (COM) (COM) Panel Thickness without ezel:.09 ~. (.0mm ~.mm) Panel Thickness with ezel:.09 ~.098 (.0mm ~.mm) CTCT MTRILS & RTINS Silver over Silver Power V C 0V C old over rass or Copper Logic Level 0.V 8V C/DC maximum old over Silver Connection (in) (.) Dia.00 (.).70 Connection (in) Panel Cutout for Single Pole without ezel Note: See Supplement section to find complete explanation of operating range. Power Level or Logic Level Connection (in) Panel Cutout for Double Pole without ezel Common V C or 0.V 8V C/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. (.).9 (.9). (.). (.9).

6 Snap-In Mount Miniature Rockers Series M TRMINLS Solder Lug 0.0 (.mm) Straight PC poxy Seal (.0). (0.8mm) Wirewrap or xtended PC.70 (9.0mm) Wirewrap or xtended PC.9 (.mm) Wirewrap or xtended PC.0 (7.0mm) Wirewrap or xtended PC T0.0 (.mm) inish: Matte Colors vailable:,, C,,,, H S T. (.mm) alse Illuminated Rocker Cap Colors vailable: (9.9). (.).0 Thk = (0.8).0 (.0).7 (.0) poxy Seal (.) (.8).0.89 (.7).0 Thk = (0.8).0 poxy Seal Thk = (0.8).0 ROCKRS & PDDLS (.7).00 Rocker alse Illuminator Material: Polycarbonate crylonitrile utadiene Styrene inish: lossy Colors: lack White and Red lack White C Red.0 (.7mm) Wide Quick Connect (.8) Dia Typ.07 Single Pole Yellow If using as extended PC terminal, refer to the above footprints. Dimension = T.0 (.mm) Wide Paddle inish: Matte Colors vailable:,, C,,,, H When a bezel is selected with T, glossy polycarbonate T07 is supplied. (.).0 (7.) (.).80.8 (.8).07 (.8). reen poxy Seal Double Pole (8.).9 (.). Thk = (0.8).0 (.8).89 (.8) Dia Typ.07 (.).0 (.7).0 terminal lengths as shown beside the terminal codes at the left. (.).09 (.).0 lue (.). (.8). H (.). (.8) R.0 (.8). (7.7).0 (.8).07 ray (.8).07 Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 7

7 Snap-In Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators T07 ezel inish: Matte T08 ezel for T070 LD Material: Polycarbonate inish: lossy Contact factory for matte finish. T ezel for T7 LD Material: Polycarbonate inish: Semi-glossy T ezel for T8 LD Material: Polycarbonate inish: Semi-glossy. Pry out tab on bezel to a angle. Tab Tab (9.0).78 (.). (.). (8.0). (.0) Typ (8.0). OPTIL SNP-IN ZLS & ZL COLORS (.). (.) Dia. (0.0).9 (0.0).9 (.0) Dia Typ.8 (.0) Typ.97 (.8). (.0).7 (.).8 (0.).9 (.).087 (.8). (.0).7 (.0).7 (.0).7 (.).087. Insert switch frame under tab and snap on bezel. (.).087 (7.8).07 (.8). (.) Sq.8 (.).087 (7.8).07 (.8). (.) Sq.8 ezel ssembly lack White Yellow lack H lack lack reen lue ray LD colors & specifications on next page. Single Pole (.)mm.9 (.)mm. LD colors & specifications on next page. LD colors & specifications on next page. Double Pole (.)mm. (.)mm.8 (.9).. Push tab back into place.. Snap assembled bezel and switch into panel. Single Pole (.)mm.9 (.9). Single Pole (8.)mm.7 Single Pole (8.)mm.7 Double Pole (.)mm. (8.8) Dia. (.8). (.9). Double Pole (8.7)mm.7 (.9). Double Pole (8.7)mm.7 8

8 Snap-In Mount Miniature Rockers Series M T070 LD or ezel T08 with LD (+) (+) (-) Top LD ottom LD Top LD ottom LD T070 T7 T8 Color Red reen Red Yellow reen Red Yellow reen Maximum orward Current I M m 0m 0m 0m m m 0m m Typical orward Current I 0m 0m 0m 0m 0m 0m 0m 0m orward Voltage V.8V.V.0V.V.V.V.V.V Maximum Reverse Voltage V RM V V V V V V V V Current Reduction Rate 0. bove C I m/ C mbient Temperature Range (when used with a bezel) (-) (.08) Dia.00 (7.7).0 LD COLORS & SPCIICTIS ezel Orientation on Switch T7 LD or ezel T with Round LDs 0.0 m/ C 0.0 m/ C 0.0 m/ C T8 LD or ezel T with Rectangular LDs Note: Lead lengths may differ from manufacturing lot to lot. The longer lead is the anode (+). C 0. m/ C 0. m/ C 0.0 m/ C 0 ~ +70 C ~ +70 C ~ +70 C The electrical specifications shown are determined at a basic temperature of C. LD circuit is independent of switch operation. LD is colored in state. If the source voltage is greater than the rated voltage of the LD, a ballast resistor must be connected in series with the lamp. The ballast resistor calculation and more lamp detail are shown in the Supplement section. (+) C LNDS (.0) Dia.8 NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Print Method: Pad Print poxy based ink is recommended. (.0).97 Suggested Printable rea for Cap T0 (-) (.) Typ.77 (0.7) Typ.00 C (9.9).90 (.).0.0 (0.7) Typ.00 (+) (.) Typ. (.0).97 Shaded areas are printable areas. (-) (7.0).7 0. m/ C Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 9

9 Snap-In Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators Snap-in rame Solder Lug M0TJW0-C Snap-in rame Solder Lug M0TJW0-C Snap-in rame Solder Lug M0TJW0-C Snap-in rame Solder Lug M0TJW0-C (8.0).709 (8.0).709 (8.0).709 (8.0).709 (.).0 (.).80 (.).0 (.).80 (.).0 (.).80 (.).0 (.).80 TYPICL SWITCH DIMNSIS (.).09 (.).09 Single Pole (.).0 (.9).9 (.8).0 (0.).00 (7.).79 Double Pole (.).0 (.9).9 Single Pole (.8). (.7).9 Double Pole (.8). (.7).9 (.8).0 (.8).0 (0.).00 (7.).79 (.8).0 (0.).00 (7.).79 (9.).7 (0.).00 (7.).79 (.).77 (9.).7 (.).77 (9.).7 (.) x (.0) Typ.0 x.0 (0.).00 (9.).7 (.) x (.0) Typ.0 x.0 (0.).00 (.).77 (.).77 (.) x (.0) Typ.0 x.0 (0.).00 (.) x (.0) Typ.0 x (0.).00.0 (7.9). (.8).89 (7.9). (.7).00 (.8).89 (.7).00 (.0). (.0) Typ (.0). (.0) Typ (.0). (.0) Typ (.0). (.0) Typ 70

10 Snap-In Mount Miniature Rockers Series M (.0).7 (.).8 (0.).90 (8.0). (.0) Dia Typ.8 (8.0). (.0) Typ.97 (.0) (.08) Dia.00 (.0).7 (.).0 (.8). (.). (.).0 (.8). (.). (0.0).9 (7.8).07 (.).0 (.8). (.) Sq.8 (0.0).9 (7.8).07 (.).0 (.8). (.) Sq.8 (.0).8 (9.0).78 (.). (.0).7 (.0).7 (.). (.).9 (.).087 (.). (.0).8 (.0).8 (.0).8 (.). (.). TYPICL SWITCH DIMNSIS Single & Double Pole (9.).7 (.).77 Double Pole (.9).9 (.) Min.0 (.).9 (.).087 (.). Single Pole (.).9 (.).087 (.). (0.).00 Double Pole (.).9 (.).087 (.). (.) x (.0) Typ.0 x.0 (9.).7 (9.).7 (.).77 (9.).7 (.).77 (.).77 (0.) Sq.0 (.) x (.0) Typ.0 x.0 (0.).00 (.) x (.0) Typ.0 x (0.).00.0 (.) x (.0) Typ.0 x (0.).00 (7.9)..0 (.0) Snap-in rame T07 ezel Solder Lug (.0). (.0). M0TJW0-C- Snap-in rame T08 ezel Solder Lug (.8).89 (.7).00 (.).098 (.0). (.0). (.0) Typ M0TJW0-C--C Snap-in rame T ezel Solder Lug (7.9). (.0) (.0). (.0). M0TJW0-C--C Snap-in rame T ezel Solder Lug (.8).89 (.7).00 (.8).89 (.0) Typ (.7).00 (.0). (.0). (.0). (.0). (.0) Typ M0TJW0-C--C Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 7

11 racket PC Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators M0 SPDT DPDT SPT Poles PDT (used only with terminal codes 0 & & frame code TX) PDT DPT (used only with terminal code & frame code TX) SPDT -- Circuit TX rame with. (9.7mm) Wide Red Rocker Circuits N N () 8 () () 9 () * * () () * 7 () ( ) = Momentary * - circuits TX TZ TX Mounting rames Narrow rame for Small ctuator Wide rame for Large ctuator DSCRIPTI OR TYPICL ORDRIN XMPL M0TX-DC W old Contacts with 0.V Rating TYPICL SWITCH Contact Materials & Ratings Silver; V C 0V C old; Rated 0.V 8V C/DC max old over Silver; V C & 0.V 8V C/DC max.0 (.8mm) Vertical PC Terminals with Support 7

12 racket PC Mount Miniature Rockers Series M ORDRIN XMPL 7 D C Terminals or TX & TZ rames Straight PC with racket (- Pole only).0 (.mm) Straight PC with. (.8mm) racket. (0.8mm) Straight PC with.0 (.0mm) racket.9 (.mm) Straight PC with.0 (9.mm) racket Straight PC with Reinforced racket (- Pole only).0 (.mm) Straight PC with. (.8mm) racket. (0.8mm) Straight PC with.0 (.0mm) racket.70 (9.0mm) Straight PC with.9 (.mm) racket Terminals or TX rame Only Right ngle PC with Support (- Pole only) 0.0 (.8mm) Right ngle PC Vertical PC with Support (- Pole).0 (.8mm) Vertical PC TZ rame with.9 (.mm) Wide Red Rocker DPDT -N- Circuit D J H Rockers & Paddles Small ctuators (TX rame). (9.7mm). (9.7mm) Wide Paddle.0 (.mm).0 (.mm) Wide Paddle Large ctuators (TZ rame).9 (.mm).9 (.mm) Wide Paddle DSCRIPTI OR TYPICL ORDRIN XMPL M0TZ-JC IMPORTNT: old Contacts with 0.V Rating.0 (.mm) Straight PC Terminals with Reinforced racket C H Rocker & Paddle Colors lack White Red Yellow reen lue ray Switches are supplied without UL & CS marking unless specified. UL & CS recognized only when ordered with marking on the switch. Specific models, ratings and ordering instructions are noted on the eneral Specifications page. Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 7

13 racket PC Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators Pole SP DP P P Model M0 M0 *M0 M08 *M09 M0 M0 *M0 M08 *M09 M0 M0 *M0 M08 *M09 M0 M0 *M0 M08 *M09 Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics Down Center Up Down Center Up () () () () N N N N N N N N () () () () () () () () () () () () POLS & CIRCUITS - OPN OPN OPN OPN or Throw (-On) Connected Terminals & Schematics Note: Terminal numbers are not actually on the switch. * Reverse circuits available for vertical mount SP & DP upon request. SPDT DPDT PDT PDT (COM) 8 (COM) (COM) 9 (COM) Pole Model Down Center Up Down Center Up SP DP M0 M0 M07 M0 M0 M07 () () The SPT model utilizes a double pole base. connection must be made during field installation. () () () () Conn Connection (in) Connection Connection (in) 8 (in) Common (in) Connection (in) Connection Connection (in) 8 (in) The DPT model utilizes a four pole base. connection must be made during field installation. Conn Common (in) Connection (in) Connection Connection (in) 8 (in) 0 Common (in) 7

14 racket PC Mount Miniature Rockers Series M TX W (8.0). TZ MOUNTIN RMS Narrow Mounting rame for Small ctuators with Straight PC Terminals (codes,, 7,,, & ) or with ngle PC Terminals (codes 0 & ) Straight PC Mounting Right ngle PC Mounting Vertical PC Mounting (.) Dia.00 (.).8 Small ctuators & Panel Cutouts for TX rame (actuator details on the following pages) T8 T9 T0 T Wide Mounting rame for Large ctuators with Straight PC Terminals (codes,, 7,,, & ) CTCT MTRILS & RTINS Silver over Silver Power V C 0V C old over rass or Copper Logic Level 0.V 8V C/DC maximum old over Silver (.) Dia.00 (.).8 (0.).98 (7.8).70 (.08).00 (.) Typ.0 Direction of ctuation T Note: See Supplement section to find complete explanation of operating range. Power Level or Logic Level (0.) Typ.0 (.08).00 Large ctuators & Panel Cutouts for TZ rame (actuator details on the following V C or 0.V 8V C/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. (.) Dia.00 (.7).7 T7 (.) Dia.00 (.0).0 (.).90 (.7).08 (.0). (.7).00 (8.). (.7).00 Direction of ctuation Direction of ctuation Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 7

15 racket PC Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators.0 (.mm) Terminal with. (.8mm) racket 0 D T8. (9.7mm) inish: Matte Cap Colors vailable: or TX and TZ - Pole Straight PC Mount with racket TRMINLS 7. (0.8mm) Terminal with.0 (.0mm) racket T0.0 (.mm) inish: Matte ROCKRS & PDDLS OR TX MOUNTIN RMS lack PC footprints are on the following Typical Switch Dimension pages. or TX - Pole Right ngle PC Mount.0 (.8mm) Right ngle PC (9.7). (.).0 (7.9). (.). (8.) (.) (.mm) Terminal with.0 (9.mm) racket (.87). (.9). White (.8). (9.9). C (7.7).0 (8.8). (.).8 (.).8 Red.0 (.mm) Terminal with. (.8mm) racket T9. (9.7mm) Wide Paddle inish: Matte or TX and TZ - Pole Straight PC Mount with Reinforced racket Yellow. (0.8mm) Terminal with.0 (.0mm) racket T.0 (.mm) Wide Paddle inish: Matte or TX - Pole Vertical PC Mount.0 (.8mm) Vertical PC reen (9.7). (.).0 lue.70 (9.0mm) Terminal with.9 (.mm) racket (8.8).70 (.). H (.).08 (.8). (.8). (.).09 ray (.9). (.8). (8.) R. (.).8 (.8) R.0 (.).8 7

16 racket PC Mount Miniature Rockers Series M J T.9 (.mm) inish: Matte (.).9 Cap Colors vailable: (8.) (.).. ROCKRS & PDDLS OR TZ MOUNTIN RMS (.78).0 lack T0- ccommodates.07 ~.090 (. ~.mm) panel thickness inish: Matte Color: lack Mounted separately from switches Cutout Tolerances: Dimension :.797 ~.80 (0. ~ 0.mm) Dimension :.9 ~.0 (.7 ~.8mm) T0- ccommodates.07 ~.090 (. ~.mm) panel thickness inish: Matte Color: lack Mounted separately from switches Cutout Tolerances: Dimension :.9 ~.0 (. ~.7mm) Dimension :.9 ~.00 (.7 ~.7mm) (.0).90 White (.0). (.).8 C Red Yellow OPTIL SNP-IN PNL RMS H T7.9 (.mm) Wide Paddle inish: Matte (.). (.).9 Used with T8 Rocker and T9 Paddle T0- ccommodates.0 ~. (.7 ~.8mm) panel thickness Used with T0 Rocker and T Paddle T0- ccommodates.0 ~. (.7 ~.8mm) panel thickness (9.8).7 reen (.). (.). (7.9).70 (.8). T0 nlarged Detail (.8).0 (.8). T0 nlarged Detail (.).09 (.8).0 lue (.7).87 (9.).7 (.) R. H (.0).7 (7.).87 (.).8 (9.9).90 (.0).98 ray (.).090 (.).090 T0 nlarged Detail Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 77

17 racket PC Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators Straight PC racket M0TX-DC Terminal Code: Straight PC Reinforced racket M0TX-DC Terminal Length: TYPICL SWITCH DIMNSIS racket Length:.0 (.mm). (.8mm). (0.8mm).0 (.0mm) 7.9 (.mm).0 (9.mm) Terminal Code: Terminal Length: (.). (.).8 TRMINL LNTH (0.) Typ.00.0 (.). (.).8 TRMINL LNTH (0.) Typ.00.0 racket Length:.0 (.mm). (.8mm). (0.8mm).0 (.0mm).70 (9.0mm).9 (.mm) (.8). (9.0).70 (8.8). (8.8). Single Pole (.) Typ.0 (7.9) Typ. (.7) Typ.0 (.7) Typ.0 (.8) Dia Typ.07 (.) Dia Typ.09 Single Pole (.8) Typ. (.7) Typ.0 (.7) Typ.0 (9.) Typ.7 (.8) Dia Typ.07 (.) Dia Typ.09 (8.0). (9.).8 (.7).00 (.7).00 Double Pole RCKT LNTH (.8) Typ.89 (.8).89 (.) Typ. (.) Typ.0 (.) Typ.09 (7.9) Typ. (.8) Dia Typ.07 (.) Dia Typ.09 Double Pole RCKT LNTH (.8) Typ.89 (.) Typ.0 (.8).89 (.) Typ.09 (.8) Typ. (9.) Typ.7 (.8) Dia Typ.07 (.) Dia Typ.09 C L C L 78

18 racket PC Mount Miniature Rockers Series M (.). (.8). (.) Typ.0 (.08).00 (.). (.8). (.) Typ.0 (.08).00 (8.8). (.8). (.) Typ.0 (.08).00 Shown in Down Position Shown in Down Position Shown in Down Position (9.7). (9.7). (9.7). (.). (8.8). (.). (8.8). Pivot Pivot (0.).0 (.) (.). (8.8). Pivot TYPICL SWITCH DIMNSIS Single Pole.7 (.0).7 Double Pole (0.) Typ.0 (.0).7 (.7).00 (.7).00 Three Pole (0.).0 (.).77 (.). (.7).00 (.7) Typ.00 (.8).0 (.7) Typ.00 (.8) Typ.0 (.0). (.0) (.0). (7.9). (.).9.0 (.7).00 (.).9.0 (7.).89 (.) (.8mm) Right ngle PC (.8) Dia Typ.07 (.) Typ.00 M0TX0-DC.0 (.8mm) Right ngle PC (.7).00 (.8).0 (.7).00 (.) Typ.00 (.8) Dia Typ.07 M0TX0-DC.0 (.8mm) Right ngle PC 8 7 (.8) Typ.0 (.). (.) Typ.00 (.8) Dia Typ.07 M0TX0-DC Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 79

19 racket PC Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators TYPICL SWITCH DIMNSIS.0 (.8mm) Vertical PC Single Pole M0TX-DC.0 (.8mm) Vertical PC Double Pole M0TX-DC.0 (.8mm) Vertical PC Three Pole M0TX-DC.0 (.8mm) Vertical PC our Pole M0TX-DC (0.) Typ.0 (.08).00 (0.) Typ.0 (.08).00 (0.) Typ.0 (.08).00 (0.) Typ.0 (.08).00 (9.7). (9.7). (9.7). (9.7). (9.).0 (.7).08 Shown in Down Position (9.).0 (.7).08 Shown in Down Position (9.).0 (.7).08 Shown in Down Position (9.).0 (.7).08 Shown in Down Position (8.8). (8.8). (.). (.97). (8.8). (.). (.97). (8.8). (.). (.). (.97). (.97). (.).8 (.).8 (.).8 (.).8 (.7).00 (.7).00 (.7).00 (.7).00 (.7).00 (.). (.7).00 (.). (.8)..0 (.8) Typ.0 (.8)..0 (.8) Typ.0 (.8)..0 (.8) Typ.0 (.8)..0 (.8) Typ.0 0 (.8) Typ.89 (7.9). 9 (.8).89 (.7) (.8) Typ.89 (7.) (.).878 (.0). (.7).00 (.0). (.7) Typ.00 (.0). (.7) Typ.00 (.0). (.7) Typ.00 (.) Typ.00 (.8) Dia Typ (.) Typ.00 (.8) Dia Typ.07 (.) Typ.09 (.8) Typ.0 (.) Typ.00 (.8) Dia Typ.07 7 (.8) Typ.0 (.7).00 (.) Typ.00 (.8) Dia Typ.07 (.7).00 (.8) Typ.89 (.8) Typ.0 (.). (.8) Typ.89 (.8) Typ.0 (.). 80

20 racket PC Mount Miniature Rockers Series M (.).0 (.).0 (.).8 TRMINL LNTH (.).8 (0.) Typ.0.0 TRMINL LNTH (0.) Typ.00.0 (.) Typ.0 (7.9) Typ. (.8) Dia Typ.07 (.) Dia Typ.09 (.8) Typ. (.8). (9.0).70 (9.) Typ.7 (.8) Dia Typ.07 (.) Dia Typ.09 (.0). (.0). TYPICL SWITCH DIMNSIS Single Pole (.) Typ.0 (.) Typ.09 (7.9) Typ. (.8) Dia Typ.07 (.) Dia Typ.09 Single Pole (.) Typ.09 (.8) Typ. (9.) Typ.7 (.8) Dia Typ.07 (.) Dia Typ.09 (.7) Typ.0 (.7) Typ.0 C L (.7) Typ.0 (.7) Typ.0 C L (8.0). (9.).8 (.7).00 Terminal Code: (.7).00 RCKT LNTH (.8) Typ.89 (.8).89 (.) Typ. RCKT LNTH (.8) Typ.89 (.) Typ.0 (.8).89 Double Pole Double Pole Terminal Length: Straight PC racket M0TZ-JC racket Length:.0 (.mm). (.8mm). (0.8mm).0 (.0mm) 7.9 (.mm).0 (9.mm) Terminal Code: Straight PC Reinforced racket Terminal Length: M0TZ-JC racket Length:.0 (.mm). (.8mm). (0.8mm).0 (.0mm).70 (9.0mm).9 (.mm) Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 8

21 racket PC Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators (.9) Typ.7 (0.7) Typ.00 LNDS NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable rea for Cap T8 T0 (7.7).0 (9.7)..0 (.7) Typ.7 (0.7) Typ.00 (.) Typ.77 (0.7) Typ.00 (9.9).90 (.).0 Shaded areas are printable areas. Recommended Print Method: Pad Print.0 (0.7) Typ.00 (.) Typ. poxy based ink is recommended. (.8) Typ.0 (0.7) Typ.00 T (.9). (.).9.0 (0.0) Typ.9 (0.7) Typ.00 8

22 lat rame Mount Miniature Rockers Series M M0 Poles SPDT DPDT SPT PDT PDT DPT Circuits N N () 8 () () 9 () * * () () * 7 () ( ) = Momentary * - circuits TYPICL SWITCH ORDRIN XMPL TN W 0 TN TY W IMPORTNT: Mounting rames.7 (.9mm) Wide lat rame.0 (.8mm) Wide lat rame Red. (9.7mm) SPDT -N- Circuit Contact Materials & Ratings Silver; V C 0V C old; Rated 0.V 8V C/DC max old over Silver; V C & 0.V 8V C/DC max Switches are supplied without UL & CS marking unless specified. UL & CS recognized only when ordered with marking on the switch. Specific models, ratings and ordering instructions are noted on the eneral Specifications page. Terminals 0 Solder Lug 0.0 (.mm) Straight PC DSCRIPTI OR TYPICL ORDRIN XMPL Solder Lug Terminals M0TNW0-DC Rockers & Paddles Small ctuators (TN rame) D. (9.7mm). (9.7mm) Wide Paddle.7 (.9mm) Wide lat rame Silver Contacts with -mp Rating.0 (.mm).0 (.mm) Wide Paddle Large ctuators (TY rame) J H.9 (.mm).9 (.mm) Wide Paddle C H Rocker & Paddle Colors lack White Red D Yellow reen lue ray C Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 8

23 lat rame Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators Pole SP DP P P Model M0 M0 M0 M08 M09 M0 M0 M0 M08 M09 M0 M0 M0 M08 M09 M0 M0 M0 M08 M09 Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics Down Center Up Down Center Up () () () () N N N N N N N N () () () () () () () () () () () () POLS & CIRCUITS - OPN OPN OPN OPN or Throw (-On) Connected Terminals & Schematics Note: Terminal numbers are not actually on the switch. SPDT DPDT PDT PDT (COM) 8 (COM) (COM) 9 (COM) Pole Model Down Center Up Down Center Up SP DP M0 M0 M07 M0 M0 M07 () () The SPT model utilizes a double pole base. connection must be made during field installation. () () () () Conn Connection (in) Connection Connection (in) 8 (in) Common (in) Connection (in) Connection Connection (in) 8 (in) The DPT model utilizes a four pole base. connection must be made during field installation. Conn Common (in) Connection (in) Connection Connection (in) 8 (in) 0 Common (in) 8

24 lat rame Mount Miniature Rockers Series M TN.7 (.9mm) Wide lat rame Mounting hardware kit HK-, as shown on the following page, must be ordered separately. MOUNTIN RMS Small ctuators & Panel Cutouts for TN rame (actuator details on the following pages) T8 T9 T0 T TY.0 (.8mm) Wide lat rame Mounting hardware kit HK-, as shown on the following page, must be ordered separately. (.).8 (0.).0 (0.).98 (.). (.9).7 (.) Dia Typ. (7.8).70 (.8).97 (.) Dia Typ.0 (.8).0 Large ctuators & Panel Cutout for TY rame (actuator details on the following pages) T (.).8 (0.).0 (.0).0 (9.). (.8).97 (.) Dia Typ.09 T7 (8.). (.9).7 (.) Dia Typ.8 (.9).7 (.).90 (.7).00 (.8).97 (.) Dia Typ.0 Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 8

25 lat rame Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators W CTCT MTRILS & RTINS Silver over Silver Power V C 0V C old over rass or Copper Logic Level 0.V 8V C/DC maximum old over Silver Note: See Supplement section to find complete explanation of operating range. Power Level or Logic V C or 0.V 8V C/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. 0 0 ace Panel Mounting rame Solder Lug STND LNTH Optional Hardware Kits for Subpanel or ace Panel Mounting Panel Thickness.0 (.mm) Straight PC MOUNTIN RMS (CTINUD) Standoff Length (.8) Dia Typ.07 Hardware Kit Number TN rame. (.7mm). (.98mm) THK- TY rame. (.7mm). (7.9mm) THK- Hardware kits include: stainless steel screws, hex nuts, lockwashers, & standoffs poxy Seal (.) (.8).0.89 (.7).0 Thk = (0.8).0 lat frame devices may also be mounted to the face panel. Standoffs are used to recess the actuator and achieve an attractive front panel appearance. TRMINLS poxy Seal (.0) (.).0 Thk = (0.8).0 Subpanel Mounting (.0).7 (.0) (.8).89 (.8) Dia Typ.07 T0- T0- (.8) Typ (.8) Dia Typ.07 Single Pole Double Pole Three Pole our Pole 7 These devices are especially designed for subpanel mounting. When installed on a mounting plate behind the panel, hardware is completely concealed and the front panel retains a clean, attractive appearance. Optional Snap-in Panel rames urther details are shown in the previous bracketed PC mount subsection. 7 T0- T0- (.8) Typ (.8) Dia Typ.07 8

26 lat rame Mount Miniature Rockers Series M D T8. (9.7mm) inish: Matte (9.7). T0.0 (.mm) inish: Matte (.).0 J (7.9). (.). (8.) (.).9.8 (.87). (.9). (.8). (9.9). (7.7).0 T.9 (.mm) inish: Matte (.).9 Cap Colors vailable: (8.) (.).. (.78).0 lack (8.8). (.).8 (.).8 (.0).90 White (.0). ROCKRS & PDDLS (.).8 C or TN rame T9. (9.7mm) Wide Paddle inish: Matte or TY rame Red (9.7). T.0 (.mm) Wide Paddle inish: Matte H (.).0 Yellow (8.8).70 (.). reen (.).08 (.8). (.8). (.9). (.).09 (8.) R. (.8). T7.9 (.mm) Wide Paddle inish: Matte (.). (.).9 (9.8).7 (.).09 (.8).0 (.).8 (.8) R.0 (.).8 lue (.7).87 (.) R. (7.).87 (.).8 H ray Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 87

27 lat rame Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators TN rame Solder Lug M0TNW0-DC TN rame Solder Lug M0TNW0-DC TN rame Solder Lug M0TNW0-DC TN rame Solder Lug M0TNW0-DC (.) Dia Typ.09 (.8).97 (9.). (.8).97 (9.). (.8).97 (9.). (.8).97 (9.). (.) Dia Typ.09 (.) Dia Typ.09 (.) Dia Typ.09 TYPICL SWITCH DIMNSIS (.9).7 (9.7). (.9).7 (9.7). (.9).7 (9.7). (.9).7 (9.7). Single Pole Double Pole Three Pole our Pole (.).8 (7.9). (9.).80 (.).8 (7.9). (9.).80 (.).8 (7.9). (9.).80 (.).8 (7.9). (9.).80 (.).8 (0.).0 (0.).0 (.).77 (.).8 (0.).0 (0.).0 (.).8 (.).77 (0.).0 (.).88 (.).8 (.).77 (0.).0 (.).88 (.) x (.0) Typ.0 x (0.).00 (.) x (.0) Typ.0 x (0.).00 (.) x (.0) Typ.0 x.0 (0.).00 (.) x (.0) Typ.0 x.0 (0.).00 (.).77 0 (7.9) (.8).89 (.7) (7.).89 (.).878 (.0). (.0) (.0) Typ (.0). (.0) Typ (.0). (.8) Typ.89 (.0) Typ (.0). (.8) Typ.89 88

28 lat rame Mount Miniature Rockers Series M (.9).7 (.). (.9).7 (.). (.9).7 (.). (.) Dia Typ. (.8).0 (.).9 TYPICL SWITCH DIMNSIS Three Pole (.) Dia Typ. (.).7 (.).8 (.) Dia Typ. (.8).0 (.).9 (.8).0 (.).9 (.).7 (8.). (0.0).9 (.).8 (8.). (0.0).9 (.).7 (0.).0 (0.0).9 (8.). (0.0).9 (.).77 (0.).0 (.).7 our Pole (.).8 (0.).0 (.).7 (.) x (.0) Typ.0 x.0 (0.).00 (.).77 (.).77.0 (0.).00 Single Pole (.) x (.0) Typ.0 x (.) x (.0) Typ.0 x.0 (0.).00 (7.9). (.0) (.0) Double Pole (7.) (.).878 (.8).89 (.0) Typ (.0). (.8) Typ.89 (.0) Typ (.0). (.8) Typ.89 (.0). (.0) Typ Double pole has barrier between terminals. TY rame Solder Lug M0TYW0-JC TY rame Solder Lug M0TYW0-JC TY rame Solder Lug M0TYW0-JC Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Toggles 89

29 lat rame Mount Miniature Rockers Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators (.9) Typ.7 (0.7) Typ.00 LNDS NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable rea for Caps T8 T0 (7.7).0 (9.7)..0 (.7) Typ.7 (0.7) Typ.00 (.) Typ.77 (0.7) Typ.00 (9.9).90 (.).0 Shaded areas are printable areas. Recommended Print Method: Pad Print.0 (0.7) Typ.00 (.) Typ. poxy based ink is recommended. (.8) Typ.0 (0.7) Typ.00 T (.9). (.).9.0 (0.0) Typ.9 (0.7) Typ.00 90