DF PROFI II PC/104-Plus

Transcription

1 DF PROFI II PC/104-Plus Installation Instructions V Project No.: 5302 Doc-ID.: DF PROFI II PC/104-Plus COMSOFT

2 d:\windoc\icp\doku\hw\dfprofi ii\installation\pc104+\version_1.4\df profi ii pc 104+ e.doc Revision History Version Date Description V Technical data table extended V Document-Adjustment V PC/104-Plus extension V Extension for using DF PROFI II as Slave V Initial Version COMSOFT GmbH Wachhausstraße 5a D Karlsruhe Phone Fax Copyright 2009 by COMSOFT GmbH This document is protected by copyright. Reproduction, duplication, publishing, transfer or disclosure of the contents of this document are only permitted after prior written agreement has been obtained from COMSOFT GmbH.

3 DF PROFI II PC/104-Plus - Installation Instructions Contents Contents 1 Installation of the Board Pin Assignment X2, PROFIBUS connector (SUB-D 9 pin) X3, Ethernet connector X4, External Ethernet LEDs X6, External PROFIBUS LEDs X X Technical Data CE-Conformity Declaration...9 COMSOFT V1.4 / i

4 Contents DF PROFI II PC/104-Plus - Installation Instructions List of Figures Figure 1: DF PROFI II PC/104-Plus Board...2 Figure 2: PROFIBUS-Terminator...3 List of Tables Table 1: Table 2: Table 3: Table 4: Table 5: Table 6: Rotary Switch Settings...1 Pin Assignment PROFIBUS SUB-D...3 X3 Pin assignment Ethernet...4 X4 Pin assignment Ethernet LEDs...5 X6 Pin assignment PROFIBUS LEDs...5 Technical Data...8 ii V1.4 / COMSOFT

5 DF PROFI II PC/104-Plus - Installation Instructions Installation of the Board 1 Installation of the Board The DF PROFI II PC/104-Plus is a Plug&Play-compatible board for 32-Bit PCI-Slots. The configuration entirely takes place by means of the delivered software or the BIOS of your PC respectively. Notice, before mounting the board you must select a board number via switch S1 (details see PC/104-Plus specification and table below). Switch Position (S1) Module Slot 0 or or or or 7 4 Table 1: Rotary Switch Settings To mount the board, please proceed as follows: Switch off your system and disconnect it from the power supply. Install the DF PROFI II PC/104-Plus board according to the safety instructions. If necessary, please refer to the operating instructions of your system. Note: Please follow the safety instructions for electronic modules against electrostatic charge. COMSOFT V1.4 /

6 Installation of the Board DF PROFI II PC/104-Plus - Installation Instructions Figure 1: DF PROFI II PC/104-Plus Board 2 V1.4 / COMSOFT

7 DF PROFI II PC/104-Plus - Installation Instructions Pin Assignment 2 Pin Assignment X2, PROFIBUS connector (SUB-D 9 pin) Pin Number Signal Function Direction 1 - shielding 3 RxD/TxD-P Data+ Input/Output 5 0V (potential free 80 Feeding of bus terminator Input ma) 6 5V (potential free 80 ma) Feeding of bus terminator Output 8 RxD/TxD-N Data- Input/Output Table 2: Pin Assignment PROFIBUS SUB-D Remark: To assure correct operation of the PROFIBUS, a terminating resistor must be mounted at each bus end (Purchase No.: H). Cable type A 390 Ω 220 Ω 390 Ω Cable type B +5V Data+ Data- 390 Ω 150 Ω 390 Ω 0V Figure 2: PROFIBUS-Terminator COMSOFT V1.4 /

8 Pin Assignment DF PROFI II PC/104-Plus - Installation Instructions X3, Ethernet connector This connector can be used to connect to Ethernet (TCP/IP). Pin Number Signal 1 TX+ 2 TX- 3 RX RX Chassis Ground 10 Chassis Ground Table 3: X3 Pin assignment Ethernet 4 V1.4 / COMSOFT

9 DF PROFI II PC/104-Plus - Installation Instructions Pin Assignment X4, External Ethernet LEDs This connector can be used to connect external LEDs inidicating the Ethernet status. The connector of the LED must be connected to Pin 1. Pin Number Signal 1 Ground 2 Link, green LED 3 TxD, red LED 4 100MBit, yellow LED Table 4: X4 Pin assignment Ethernet LEDs X6, External PROFIBUS LEDs This connector can be used to connect external LEDs indicating the PROFIBUS status. The + connector of the LED must be connected to Pin 1. The meaning of the LEDs is described in the GettingStarted documentation. Pin number Signal 1 3,3V 2 LED 1, green 3 LED 2, yellow 4 LED 3, red Table 5: X6 Pin assignment PROFIBUS LEDs COMSOFT V1.4 /

10 Pin Assignment DF PROFI II PC/104-Plus - Installation Instructions X5 This connector is reserved for internal use and must not be connected X7 This connector is reserved for internal use and must not be connected. 6 V1.4 / COMSOFT

11 DF PROFI II PC/104-Plus - Installation Instructions Description of the LED's 3 Description of the LED's Green LED: On: Firmware loaded and started Off: Firmware not loaded Yellow LED: On: PROFIBUS started Off: PROFIBUS stopped Red LED: On: PROFIBUS-Failure (min. one slave not connected to the bus or with external diagnosis) Off: No PROFIBUS-Failure COMSOFT V1.4 /

12 Technical Data DF PROFI II PC/104-Plus - Installation Instructions 4 Technical Data Processor Net+Arm 40, 33 MHz PROFIBUS Controller ASPC2, 48 MHz Memory 1 Mbyte SRAM 2 Mbyte Flash Memory PROFIBUS interfaces 1 * Sub-D 9 pins Interface physics RS485 (isolated) LAN interfaces (optional) 1 * RJ45 Interface physics Ethernet 10/100 Mbit/s PROFIBUS data rates 9600 Bit/s Bit/s Data Size of Process Image max. 8 KByte PROFIBUS Isolation Voltage 500 VDC Power consumption +5V / 1100 ma Ambient Temperature Range 0 55 C Dimensions 95 mm * 90 mm Table 6: Technical Data 8 V1.4 / COMSOFT

13 DF PROFI II PC/104-Plus - Installation Instructions CE-Conformity Declaration 5 CE-Conformity Declaration We herewith declare that the PC-interface DF PROFI II PC 104+ corresponds to the requirements stated in the EU standards 89/336/EEC. The interface corresponds to the following standards: EN 55024, issue EN 55022, issue Manufacturer: COMSOFT GmbH Wachhausstr. 5a D Karlsruhe COMSOFT V1.4 /