DVSD / DVSE6800+ Dual SDI / ASI Serial Digital Video Distribution Amplifiers

Transcription

1 Installation and Operation Manual DVSD / DVSE6800+ Dual SDI / ASI Serial Digital Video Distribution Amplifiers Edition C Delivering the Moment

2 Publication Information 2014 Imagine Communications Corp. Proprietary and Confidential. Imagine Communications considers this document and its contents to be proprietary and confidential. Except for making a reasonable number of copies for your own internal use, you may not reproduce this publication, or any part thereof, in any form, by any method, for any purpose, or in any language other than English without the written consent of Imagine Communications. All others uses are illegal. This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product. Trademarks 6800+, ADC, CCS Navigator, Channel ONE, ChannelView, ClipSync, Delay, D Series, D Series DSX, Deliver the Moment, Delivering the Moment, FAME, Farad, G8, G Scribe, HView, IconMaster, IconLogo, IconStation, IconKey, InfoCaster, InfoCaster Creator, InfoCaster Manager, InfoCaster Player, InstantOnline, Invenio, Live Update, mcapture, Magellan, Magellan CCS Navigator, Magellan Q SEE, MultiService SDN, NetPlus, NetVX, NewsForce, Nexio G8, Nexio AMP ChannelView, Nexio Channel ONE, Nexio ClipSync, Nexio Delay, Nexio Digital Turnaround Processor, Nexio Farad, Nexio G Scribe, Nexio IconKey, Nexio IconLogo, Nexio IconMaster, Nexio IconStation, Nexio InfoCaster, Nexio InfoCaster Creator, Nexio InfoCaster Manager, Nexio InfoCaster Player, Nexio InfoCaster Traffic, Nexio InstantOnline, Nexio mcapture, Nexio News- Force, Nexio NXIQ, Nexio Playlist, Nexio Remote, Nexio RTX Net, Nexio TitleMotion, Nexio TitleOne, Nexio Velocity ESX, Nexio Velocity PRX, Nexio Velocity XNG, Nexio Volt, OPTO+, Panacea, Platinum, Playlist, Predator II GRF, Predator II GX, Punctuate, Remote, RTX Net, QuiC, Q SEE, SD STAR, Selenio, Selenio 6800+, SelenioNext, Selenio X50, Selenio X85, Selenio X100, TitleMotion, TitleOne, Velocity ESX, Velocity PRX, Velocity XNG, Versio, Videotek SD STAR, X50, and X85 are trademarks of Imagine Communications or its subsidiaries. Altitude Express, Connectus, Enabling PersonalizedTV, ICE Broadcast System, ICE Illustrate, ICE Q algorithms, ICE- PAC, Imagine ICE, Inscriber, Inscriber Connectus, Invenio, NEO, Nexio, Nexio AMP, PersonalizedTV, Router- Works, Videotek, Videotek ASI STAR, Videotek GEN STAR, and Videotek HD STAR are registered trademarks of Imagine Communications or its subsidiaries. Microsoft and Windows are registered trademarks of Microsoft Corporation. HD BNC is a trademark of Amphenol Corporation. Some products are manufactured under license from Dolby Laboratories. Dolby and the double D symbol are registered trademarks of Dolby Laboratories. DTS Neural audio products are manufactured under license from DTS Licensing Limited. DTS and the Symbol are registered trademarks & the DTS Logos are trademarks of DTS, Inc DTS, Inc. All other trademarks and trade names are the property of their respective companies. Contact Information Imagine Communications has office locations around the world. For locations and contact information see: us/ Support Contact Information For support contact information see: Support Contacts: support/ ecustomer Portal: Imagine Communications Corp. Proprietary and Confidential

3 Preliminary Contents are proprietary and confidential. Do not photocopy or distribute. DVSD / DVSE6800+ Dual SDI / ASI Video Distribution Amplifiers Installation and Operation Manual Edition C March 2006

4

5 Contents Preface Manual Information... vii Purpose... vii Audience... vii Revision History... vii Writing Conventions... viii Obtaining Leitch Documents... viii Unpacking / Shipping Information... ix Safety Standards and Compliances...x Safety Terms and Symbols...x Restriction on Hazardous Substances (RoHS) Directive... xi Waste from Electrical and Electronic Equipment (WEEE) Directive... xii Chapter 1: Introduction Overview...1 Product Description...2 Typical Broadcast and Production Applications...2 Main Features...2 Module Descriptions...3 Front Module...3 Back Modules...4 Signal Flow...6 Chapter 2: Installation Overview...9 Maximum Frame Power Ratings...10 Unpacking the Module...11 DVSD / DVSE6800+ Installation and Operation Manual v

6 Contents Preparing for Installation Checking the Packing List Setting Jumpers Installing Modules Required Frames and Back Module Connector Types Installing DVSD / DVSE6800+ Modules Removing DVSD / DVSE6800+ Modules Making Connections Chapter 3: Operation Overview Understanding Jumper Controls Introducing Jumper Control Types P1 Jumpers P2 / P3 Jumpers Understanding Parameter Types Adjustable Parameters Read-Only Parameters Operating Notes Setting Remotely-Controlled Parameters Changing Parameter Settings Recalling Default Parameter Settings Reading the Software Version Reading the Hardware Version LEDs and Alarms Module Status Indicator LED Alarms Other LED Descriptions Chapter 4: Specifications Overview Inputs Outputs Power Consumption Propagation Delay Temperature Start-Up Time Index Keywords vi DVSD / DVSE6800+ Installation and Operation Manual

7 Preface Manual Information Purpose Audience Revision History This manual details the features, installation procedures, operational procedures, and specifications of the DVSD / DVSE6800+ dual SDI / ASI video distribution amplifier. This manual is written for engineers, technicians and operators responsible for the installation, setup, and / or operation of the DVSD / DVSE6800+ dual SDI / ASI video distribution amplifier. Table P-1. Manual Revision History Edition Date Revision History A September 2005 Initial release B September 2005 Added information concerning 6800 / 7000 frames Updated information in Maximum Frame Power Ratings section Added note concerning unused input termination C March 2006 Removed information concerning 6800 / 7000 frame Added information concerning SDO1, SDO2, and LOS DVSD / DVSE6800+ Installation and Operation Manual vii

8 Preface Writing Conventions To enhance your understanding, the authors of this manual have adhered to the following text conventions: Table P-2. Manual Style and Writing Conventions Term or Convention Bold Italics CAPS Description Indicates dialog boxes, property sheets, fields, buttons, check boxes, list boxes, combo boxes, menus, submenus, windows, lists, and selection names. Indicates addresses, the names of books or publications, and the first instances of new terms and specialized words that need emphasis. Indicates a specific key on the keyboard, such as ENTER, TAB, CTRL, ALT, or DELETE. Code Indicates variables or command-line entries, such as a DOS entry or something you type into a field. > Indicates the direction of navigation through a hierarchy of menus and windows. hyperlink Internet address Note Indicates a jump to another location within the electronic document or elsewhere Indicates a jump to a Web site or URL Indicates important information that helps to avoid and troubleshoot problems. Obtaining Leitch Documents Leitch documents can be viewed or downloaded from the Leitch Web site at (go to Support>Documentation). Alternatively, contact your Leitch customer service representative to request a document. viii DVSD / DVSE6800+ Installation and Operation Manual

9 Preface Unpacking / Shipping Information Leitch has carefully inspected, tested, and calibrated this product before shipment to ensure years of stable and trouble free service. 1. Check equipment for any visible damage that may have occurred during transit. 2. Confirm that you have received all items listed on the packing list. 3. Contact your Leitch dealer if any item on the packing list is missing. 4. Contact the carrier if any item is damaged. 5. Remove all packaging material from the product and its associated components before you install the unit. Keep at least one set of original Leitch packaging, in the event that you need to return a product for servicing. If the original packaging is not available, you can purchase replacement packaging from Leitch at a modest cost or supply your own packaging as long as it meets the following criteria: Withstands the weight of the product Holds the product rigid within the packaging Leaves at least two inches of space between the product and the container Protects the corners of the product Ship products back to Leitch for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, Leitch will return the product prepaid after servicing. DVSD / DVSE6800+ Installation and Operation Manual ix

10 Preface Safety Standards and Compliances Safety Terms and Symbols See the Safety Instructions and Standards Manual to find the safety standards and compliances for this series product. A safety manual is shipped with every FR6802+ Frame Installation and Operation Manual and can be downloaded from the Leitch Web site at Alternatively, contact your Leitch customer service representative for a copy of this safety manual. This product manual uses the following safety terms and symbols to identify certain conditions or practices. See the Safety Instructions and Standards Manual for more information. Table P-3. Safety Terms and Symbols WARNING: Identifies conditions or practices that can result in personal injury or loss of life high voltage is present. Uninsulated dangerous voltage within the product s enclosure may be sufficient to constitute a risk of electric shock to persons. CAUTION: Identifies conditions or practices that can result in damage to the equipment or other property. Important operating and maintenance (servicing) instructions are included in the literature accompanying the product. x DVSD / DVSE6800+ Installation and Operation Manual

11 Preface Restriction on Hazardous Substances (RoHS) Directive Directive 2002 / 95 / EC commonly known as the European Union (EU) Restriction on Hazardous Substances (RoHS) sets limits on the use of certain substances found in electrical and electronic equipment. The intent of this legislation is to reduce the amount of hazardous chemicals that may leach out of landfill sites or otherwise contaminate the environment during end-of-life recycling. The Directive takes effect on July 1, 2006, and it refers to the following hazardous substances: Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr-V1) Polybrominated Biphenyls (PBB) Polybrominated Diphenyl Ethers (PBDE) In accordance with this EU Directive, all Leitch Technology products sold in the European Union will be fully RoHS-compliant and lead-free. (See the Leitch Web site, for more information on dates and deadlines for compliance.) Spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation. Leitch equipment that complies with the EU directive will be marked with a RoHS-compliant symbol, as shown in Figure P-1. Figure P-1. RoHS Compliance Symbol DVSD / DVSE6800+ Installation and Operation Manual xi

12 Preface Waste from Electrical and Electronic Equipment (WEEE) Directive The European Union (EU) Directive 2002 / 96 / EC on Waste from Electrical and Electronic Equipment (WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. Effective August 13, 2005, producers or users will be required to recycle electrical and electronic equipment at end of its useful life, and must not dispose of the equipment in landfills or by using other unapproved methods. (Some EU member states may have different deadlines.) In accordance with this EU Directive, Leitch Technology International, Inc. and other companies selling electric or electronic devices in the EU will affix labels indicating that such products must be properly recycled. (See the Leitch Web site, for more information on dates and deadlines for compliance.) Contact your local Leitch sales representative for information on returning these products for recycling. Leitch equipment that complies with the EU directive will be marked with a WEEE-compliant symbol, as shown in Figure P-2. Figure P-2. WEEE Compliance Symbol xii DVSD / DVSE6800+ Installation and Operation Manual

13 Chapter 1 Introduction Overview This chapter introduces the DVSD / DVSE6800+, and includes the following topics: Product Description on page 2 Module Descriptions on page 3 Signal Flow on page 6 DVSD / DVSE6800+ Installation and Operation Manual 1

14 Chapter 1: Introduction Product Description The DVSD / DVSE6800+ dual distribution amplifiers provide two channels of SD-ASI video distribution; the DVSE6800+ also provides cable equalizing and reclocking. The DVSD / DVSE6800+ dual distribution amplifiers provide four outputs for each input (two 1 4s), and provide a method that allows for a single channel distribution amplifier with 8 outputs (one 1 8). DVSD / DVSE6800+ dual distribution amplifiers feature high video performance, low cost, and remote indication of signal presence and alarms. They feature high video performance, low cost, remote control, and diagnostic capability in Leitch's control system. The DVSD6800+ can distribute any Mb / s data within the amplitude limitation. The DVSE6800+ can handle 143 Mb / s, 177 Mb / s, 270 Mb / s, 360 Mb / s and 540 Mb / s serial digital video signals; and SMPTE 310 and ASI signals. You can set up, control, and monitor a DVSD / DVSE6800+ locally via card-edge jumper or remotely on a PC. For remote control, you can use either a serial RS-232 or optional ICE6800+ Ethernet connection. Typical Broadcast and Production Applications Main Features The DVSD / DVSE6800+ dual amplifier can be used in broadcast, cable, production, educational, and auditorium applications where a low cost method of distributing SDI / ASI video signals is required. DVSD / DVSE6800+ Two inputs, four outputs per input (two 1 4s) or one input, eight outputs (one 1 8) Identical polarity between input and outputs (ASI compliance) Automatic cable equalization Automatic bypass if the signal cannot be reclocked Manual (force ) bypass option Input signal presence detect Auto cable EQ Alarm output 2 DVSD / DVSE6800+ Installation and Operation Manual

15 Chapter 1: Introduction DVSE6800+ Only Module Descriptions Auto / manual reclock (19.4 / 143 / 177 / 270 / 360 / 540 Mb / s) Reclocking status report Auto bypass Front Module Figure 1-1 is a generic top-front view of a typical DVSD / DVSE6800+ module and shows the general location of standard LEDs, controls, and jumpers. See page 23 for descriptions of the control and monitoring LEDs. See page 16 for descriptions of the jumpers. Figure 1-1. DVSD / DVSE6800+ Dual Distribution Amplifier Module DVSD / DVSE6800+ Installation and Operation Manual 3

16 Chapter 1: Introduction Back Modules FR6802+ Frame Back Module Figure 1-2 shows the double-width back connector module used by the Note DVSD / DVSE6800+ when installed in an FR6802+ frame. Distribution amplifiers with unused inputs should have the input terminated. Not doing so may cause erroneous readings of a valid input signal that can be induced from adjacent slots. Figure 1-2. Back Module for FR6802+ Frame 4 DVSD / DVSE6800+ Installation and Operation Manual

17 Chapter 1: Introduction Signal Input / Output Connections for FR6802+DM Frames Figure 1-3 shows the signal input / output connections used by the Note DVSD / DVSE6800+ when installed in an FR6802+DM frame. Distribution amplifiers with unused inputs should have the input terminated. Not doing so may cause erroneous readings of a valid input signal that can be induced from adjacent slots. Figure 1-3. Back Module for FR6802+DM Frame DVSD / DVSE6800+ Installation and Operation Manual 5

18 Chapter 1: Introduction Signal Flow Figure 1-4. DVSD6800+ Signal Flow Diagram 6 DVSD / DVSE6800+ Installation and Operation Manual

19 Chapter 1: Introduction Figure 1-5. DVSE6800+ Signal Flow Diagram DVSD / DVSE6800+ Installation and Operation Manual 7

20 Chapter 1: Introduction 8 DVSD / DVSE6800+ Installation and Operation Manual

21 Chapter 2 Installation Overview Caution Before installing this product, read the Series Safety Instructions and Standards Manual shipped with every FR6802+ Frame Installation and Operation Manual or downloadable from the Leitch Web site at This safety manual contains important information about the safe installation and operation of series products. This chapter describes the DVSD / DVSE6800+ installation process, including the following topics: Installing DVSD / DVSE6800+ Modules on page 14 Making Connections on page 14 Maximum Frame Power Ratings on page 10 Removing DVSD / DVSE6800+ Modules on page 14 Required Frames and Back Module Connector Types on page 14 Setting Jumpers on page 12 Unpacking the Module on page 11 See the FR6802+ Frame Installation and Operation Manual for information about installing and operating an FR6802+ frame and its components. The DVSD / DVSE6800+ cannot be installed in a 6800 / 7000 series frame. DVSD / DVSE6800+ Installation and Operation Manual 9

22 Chapter 2: Installation Maximum Frame Power Ratings Power consumption information is listed in Chapter 4: Specifications, on page 27. Table 2-1 describes the maximum allowable power ratings for frames.note the given maximums before installing any modules in your frame. DVSD / DVSE6800+ modules can be installed in FR6802+ frames. They cannot be installed in 6800 / 7000 series frames. Table 2-1. Maximum Power Ratings for Frames Frame Type FR6802+DM (frame without fans) FR6802+DMF (frame with fans) FR6802+X (frame without fans) FR6802+XF (frame with fans) FR6802+DM48 (frame without fans) FR6802+DMF48 (frame with fans) FR6802+X48 (frame without fans) FR6802+XF48 (frame with fans) Power Supply Type Max. Frame Power Dissipation Number of Usable Slots AC 50 W 10 5 W AC 120 W W AC 50 W W AC 120 W 20 6 W DC 50 W W DC 105 W W DC 50 W W DC 105 W W Max. Power Dissipation Per Slot 10 DVSD / DVSE6800+ Installation and Operation Manual

23 Chapter 2: Installation Unpacking the Module Preparing for Installation Note Contact your Leitch customer service representative if parts are missing or damaged. Checking the Packing List Before you install the DVSD / DVSE6800+, perform the following: Check the equipment for any visible damage that may have occurred during transit. Confirm receipt of all items on the packing list. See Checking the Packing List for more information. Remove the anti-static shipping pouch, if present, and all other packaging material. Retain the original packaging materials for possible re-use. See Unpacking/ Shipping Information on page ix for information about returning a product for servicing. Table 2-2. DVSD / DVSE6800+ Packing List Ordered Product Content Description DVSD / DVSE6800+ One DVSD / DVSE6800+ front module One DVSD / DVSE6800+ Installation and Operation Manual DVSD / DVSE6800+D One DVSD / DVSE6800+ front module One standard double-slot back connector One DVSD / DVSE6800+ Installation and Operation Manual DVSD / DVSE6800+DR One standard double-slot back connector DVSD / DVSE6800+ Installation and Operation Manual 11

24 Chapter 2: Installation Setting Jumpers Note You need to configure modules for local or remote operation before power-up. To change the configuration, first remove power from the module, reset the jumper, and then reapply power. The DVSE6800+ module has three standard jumpers; the DVSD6800+ has one standard jumper. (The DVSD6800+ only uses the P1 jumper set.) Follow this procedure to set the jumper for the proper signal: 1. Locate jumper sets on the module. Figure 2-1 shows the standard location of the P1, P2, and P3 jumper sets. Figure 2-1. Location of the Jumper Sets 2. Place a jumper on the P1 pin that corresponds to the setting that you want. See Figure 2-2. Figure 2-2. P1 Jumper Set Settings See P1 Jumpers on page 16 for more information about P1 jumper set settings. 12 DVSD / DVSE6800+ Installation and Operation Manual

25 Chapter 2: Installation 3. (For DVSE6800+ only) Place a jumper on the P2 and / or P3 pin that corresponds to the reclocker output setting that you want. See Figure 2-3. Figure 2-3. P2 / P3 Jumper Set Settings See P2 / P3 Jumpers on page 17 for more information about P2 and P3 jumper set settings. DVSD / DVSE6800+ Installation and Operation Manual 13

26 Chapter 2: Installation Installing Modules Required Frames and Back Module Connector Types Note DVSD / DVSE6800+ modules with unused inputs should have the input terminated. Not doing so may cause erroneous readings of a valid input signal that can be induced from adjacent slots. The DVSD / DVSE6800+ modules have double-width back connectors that can be installed in an FR6802+X(F) frame. See the FR6802+ Frame Installation and Operation Manual for details on installing back connectors in an FR6802+ frame. Installing DVSD / DVSE6800+ Modules These modules require no specialized installation procedures. See the FR6802+ Frame Installation and Operation Manual for information about installing and operating an FR6802+ frame and its components. Removing DVSD / DVSE6800+ Modules Making Connections These modules require no specialized removal procedures. See the FR6802+ Frame Installation and Operation Manual for information about removing components in an FR6802+ frame. Once you have installed your DVSD / DVSE6800+ modules, you can connect them to the appropriate input and outputs. 14 DVSD / DVSE6800+ Installation and Operation Manual

27 Chapter 3 Operation Overview This chapter describes how to operate the DVSD / DVSE6800+ using card-edge controls only. See the following Leitch documents for information on how to operate this product remotely: +Pilot Lite User Manual for serial control interface CCS Navigator, Pilot, CoPilot, or RCP-CCS-1U Remote Control Panel Installation and Operation Manual for Ethernet control interface The following topics are discussed in this chapter: Changing Parameter Settings on page 22 LEDs and Alarms on page 23 Operating Notes on page 19 Setting Remotely-Controlled Parameters on page 21 Understanding Jumper Controls on page 16 DVSD / DVSE6800+ Installation and Operation Manual 15

28 Chapter 3: Operation Understanding Jumper Controls Introducing Jumper Control Types Figure 3-1. Location of the Jumper Sets and Status Indicators P1 Jumpers Note Both DVSD6800+ and DVSE6800+ modules use the P1 jumper set. You can use the P1 jumper set to select the following items: SDO1 and SDO2 Loss of signal switch (LOS) Remote control SDO1 / SDO2 SDO1 and SDO2 allow you to select where to direct output. By using SDO1 and SDO2, you can configure the module to operate as either 1 8 (SDO1) or dual 1 4 (SDO2). When the shunt is installed on the jumper the noted output is fed from input 2. When SDO1 is selected, the distribution amplifier functions as a 1 8 with all 8 outputs fed from input 1. LOS enabled will allow input 2 to serve as a backup to input 1. When SDO2 is selected, the distribution amplifier functions as a dual 1 4 with each input driving 4 outputs. Input 2 can be used in conjunction with the LOS enabled to provide a backup input. 16 DVSD / DVSE6800+ Installation and Operation Manual

29 Chapter 3: Operation Loss of Signal Switch Remote Control P2 / P3 Jumpers Note DVSD6800+ modules do not use the P2 and P3 jumper sets. When the Loss of Signal (on input 1) switch is enabled, the module automatically switches the output MUX to select input 2 when input 1 has lost its input signal. When the input 1 signal returns, the output mux will return input 1 to its previous output state. When the jumper is set to the remote position, the reclocker setting is handled by +Pilot Lite only. You may select the three setting modes (automatic, manual, and bypass) remotely via +Pilot Lite. You can use the P2 (for input 1 rate control) or P3 (for input 2 rate control) jumper on the DVSE6800+ to select local control reclock setting operation mode. Figure 3-1 on page 16 illustrates the location of these jumpers. Local Control Note Leitch recommends that you use the available software control options (serial / local or Ethernet / remote) to aid in viewing, setting, and confirming parameter values. In the local control reclock setting operation mode, all of the settings data status information appears on the +Pilot Lite control screen; however, you cannot change any setting in this mode via +Pilot Lite. To control the reclocking setting mode via +Pilot Lite, set the jumper to the remote control reclock setting operation mode. For local control, P2 / P3 is used to determine reclocking mode: Table 3-1. P2 / P3 Local Control Reclock Modes Reclock Mode AUTO Description Automatically detects the rate 143 / 19.4 Forces channel to lock to a 143 Mb / s or a 19.4 Mb / s signal Set the jumper on the pin that allows the reclocker to handle 143 Mb / s or 19.4 Mb / s data only If the reclocking is successful, the 143 Mb / s 19.4 Mb / s LED will be green, and the Reclock status LED indicator next to HI (for 143 Mb / s) or next to LO (for 19.4 Mb / s) will be green If the reclocking is not successful, the 143 Mb / s 19.4 Mb / s LED will be off, the Reclock status LED indicator will be off, and un-reclocked data will be present at output DVSD / DVSE6800+ Installation and Operation Manual 17

30 Chapter 3: Operation Table 3-1. P2 / P3 Local Control Reclock Modes (Continued) Reclock Mode Description 177 Forces channel to lock to a 177 Mb / s signal Set the jumper on the pin that allows the reclocker to handle 177 Mb / s data only If the reclocking is successful, the 177 Mb / s LED will be green If the reclocking is not successful, the 177 Mb / s LED will be off and un-reclocked data will be present at output 270 Forces channel to lock to a 270 Mb / s signal Set the jumper on the pin that allows the reclocker to handle 270 Mb / s data only If the reclocking is successful, the 270 Mb / s LED will be green If the reclocking is not successful, the 270 Mb / s LED will be off and un-reclocked data will be present at output 360 Forces channel to lock to a 360 Mb / s signal Set the jumper on the pin that allows the reclocker to handle 360 Mb / s data only If the reclocking is successful, the 360 Mb / s LED will be green If the reclocking is not successful, the 360 Mb / s LED will be off and un-reclocked data will be present at output 540 Forces channel to lock to a 540 Mb / s signal Set the jumper on the pin that allows the reclocker to handle 540 Mb / s data only If the reclocking is successful, the 540 Mb / s LED will be green If the reclocking is not successful, the 540 Mb / s LED will be off and un-reclocked data will be present at output LO RANGE Selects either 143 Mb / s or 19.4 Mb / s signal If the Reclock status LED indicator next to LO is green, then 19.4 Mb / s signal is selected. If the Reclock status LED indicator next to HI is green, then 143 Mb / s signal is selected. See Figure 3-1 on page 16 for the location of the reclock status indicators. Bypass Forces channel to bypass the reclocker 18 DVSD / DVSE6800+ Installation and Operation Manual

31 Chapter 3: Operation Understanding Parameter Types Adjustable Parameters Read-Only Parameters Operating Notes Most DVSD / DVSE6800+ parameters are adjustable, and can be set using either card-edge controls (see Introducing Jumper Control Types on page 16) or a software application. However, there are some parameters that are considered read-only and cannot be changed. Indicated by the abbreviation [RO], these parameters provide status and feedback information only. Two types of adjustable parameters can be changed using the card-edge controls: Numerical parameters which require you to select a value within a numerical range Selectable parameters which require you to select a specific option Both numerical and selectable parameter changes are immediate. Use the available software controls (serial/ local or Ethernet / remote network) to view and monitor parameter selections. Many of the read-only parameters are also represented by LEDs on the front of the module s card edge. See Figure 3-1 on page 16 for the location of these LEDs. When setting the control parameters on the DVSD / DVSE6800+, observe the following: When you change a parameter, the effect is immediate. However, the module requires up to 20 seconds to save the latest change. After 20 seconds, the new settings are saved and will be restored if the module loses power and must be restarted. When setting the control parameters on the DVSE6800+, observe the following: DVSD / DVSE6800+ Installation and Operation Manual 19

32 Chapter 3: Operation When the module is set to remote control, the reclocking mode is controlled by the CCS control software application. When the module powers up with remote selected, the reclocking mode is set to the last known value. When the module is set to local control, the reclocking mode is controlled by adjusting the card-edge jumper to the appropriate setting. Reclocking mode selections are reflected in the CCS control software application. Any remote attempts to adjust the reclocking mode will have no effect. If a card-edge jumper is not installed the reclocking mode is set to Auto. Modules with unused inputs should have the input terminated. Not doing so may cause erroneous readings of a valid input signal that can be induced from adjacent slots. 20 DVSD / DVSE6800+ Installation and Operation Manual

33 Setting Remotely-Controlled Parameters Table 3-2. Remotely Controlled Parameters Name Range Description Loss of Signal Switch Ch. 1 / 2 Signal Present [RO] Ch. 1 / 2 Output Select Ch. 1 / 2 Loss of Input Alarm DVSE6800+ Only Ch. 1 / 2 Loss of Lock Alarm Ch. 1 / 2 Re-clocking Mode 0 = Disable* 1 = Enable 0 = No 1 = Yes 0 = Input 1* 1 = Input 2 0 = Disabled* 1 = Enabled 0 = Disabled* 1 = Enabled 0 = Auto 1 = = = = = = = Bypass Chapter 3: Operation Table 3-2 describes DVSD / DVSE6800+ parameters that are accessible remotely. See your CCS control software application manual or online help for more information on setting and monitoring the following parameters remotely. Items marked with an asterisk (*) are the default values. Loss of signal (on input 1) switching enable, automatically switch both output MUXs to select input 2 when input 1 has lost its input signal. If LOSen is enabled: Input 1 is monitored; if Input 1 is lost, all outputs will be switched to Input 2 (applies to 1 8 Input 1 configuration and dual 1 4 configuration) If any of the outputs are already set to Input 2 (e.g., 1 8 Input 2), nothing changes Input 1 / 2 signal is present Ch. 1 / 2 output select; selects which input channel to output (used to configure the module to operate as either 1 8 or dual 1 4) Enables or disables the Loss of Input alarm for channel 1 or channel 2 Enables or disables the Loss of Lock alarm for channel 1 or channel 2 Determines reclocking mode DVSD / DVSE6800+ Installation and Operation Manual 21

34 Chapter 3: Operation Table 3-2. Remotely Controlled Parameters (Continued) Name Range Description Ch. 1 / 2 Locked Data Rate [RO] 0 = Unknown 1 = = = = = = = Bypass Changing Parameter Settings You can change DVSD / DVSE6800+ parameter settings locally with the card-edge jumper or remotely by selecting the Reclocking Mode parameter setting. Recalling Default Parameter Settings Reading the Software Version Reading the Hardware Version Input data rate feedback (NOTE: If an input loses lock, that channel will automatically go into Bypass mode.) You cannot recall default parameter settings for the DVSD / DVSE The current software version of your DVSD / DVSE6800+ module can be viewed using Pilot (via Ethernet control). See your CCS Pilot User Manual or Online Help for information on viewing software versions. The current hardware revision of your DVSD / DVSE6800+ module can be viewed using Pilot (via Ethernet control). See your CCS Pilot User Manual or Online Help for information on viewing hardware identifiers. 22 DVSD / DVSE6800+ Installation and Operation Manual

35 Chapter 3: Operation LEDs and Alarms Module Status Indicator LED The DVSD / DVSE6800+ module has a module status indicator LED that reports the state of the module. See Figure 3-1 on page 16 for the location of this LED, and Table 3-3 for a definition of the LED colors. Table 3-3. Status LED Descriptions LED Color Sequence Off Green Amber Meaning There is no power to the module; the module is not operational There is power to the module; the module is operating properly There is an alarm condition Alarms Alarms are usually logged and monitored within the available software control applications (for example, +Pilot Lite or Pilot). See the appropriate software control user manual or online help for more information. Other LED Descriptions Each module has a number of LEDs assigned to indicated varying states / functions. For DVSD / DVSE6800+ modules, these functions are listed in Table 3-4.See Figure 3-1 on page 16 for the location of these LEDs. Table 3-4. Module-Specific Status LEDs Name Color Function Status Off No power, module not operational Green Module operational Red / Green Module operational and there is an alarm 143 * / 19.4 * Green This rate selected in Manual mode OR This rate detected in Auto mode DVSD / DVSE6800+ Installation and Operation Manual 23

36 Chapter 3: Operation Table 3-4. Module-Specific Status LEDs (Continued) Name Color Function 177 * Green This rate selected in Manual mode OR This rate detected in Auto mode 270 * Green This rate selected in Manual mode OR This rate detected in Auto mode 360 * Green This rate selected in Manual mode OR This rate detected in Auto mode 540 * Green This rate selected in Manual mode OR This rate detected in Auto mode HI / LO * Green Indicates which rate is selected or deselected HI indicates 143 LO indicates 19.4 (This LED corresponds to P2 / P3 jumper LO RANGE reclock mode setting) LOCK * Green Signal is locked PRES Green Signal is present * DVSE6800+ modules only 24 DVSD / DVSE6800+ Installation and Operation Manual

37 Chapter 4 Specifications Overview The following specification tables appear in this chapter: Inputs on page 26 Outputs on page 26 Power Consumption on page 27 Propagation Delay on page 27 Start-Up Time on page 27 Temperature on page 27 Specifications and designs are subject to change without notice. DVSD / DVSE6800+ Installation and Operation Manual 25

38 Chapter 4: Specifications Inputs Note DVSD / DVSE6800+ modules with unused inputs should have the input terminated. Not doing so may cause erroneous readings of a valid input signal that can be induced from adjacent slots. Table 4-1. DVSD / DVSE6800+ Input Specifications Item Specification Number of inputs 2 Signal type SDI, ASI Connector BNC (IEC169-8) Impedance 75Ω Return loss >18 db to 540 MHz Cable equalization 300 m Belden 1694 Outputs Table 4-2. DVSD / DVSE6800+ Output Specifications Item Number of outputs SDI ASI Signal type Connector Impedance Return loss Specification 8 (1 8 configuration) 4 (2 4 configuration) SDI, ASI BNC (IEC169-8) 75Ω >18 db to 540 MHz Signal level 800 mv ± 10% DC offset 0.0 V ± 0.5 V Rise and fall time ps (20% to 80% amplitude) Overshoot < 10% of amplitude Jitter <0.2 UI (740 ps) peak-to-peak 26 DVSD / DVSE6800+ Installation and Operation Manual

39 Chapter 4: Specifications Power Consumption Table 4-3. Power Consumption Specifications Item DVSD6800+ DVSE6800+ Specification +6.8 Vdc, 0.5 A, 3.5 W +6.8 Vdc, 0.8 A, 5.5 W Propagation Delay Table 4-4. Measured Propagation Delay Specifications Item DVSD6800+ (all bit rates) DVSE6800+ Bypass mode (all bit rates) 19.4 Mbps reclock 143 Mbps reclock 177 Mbps reclock 270 (525/ 625 / ASI) Mbps reclock 360 Mbps reclock 540 Mbps reclock Specification < 8.0 ns < 9.0 ns 48.0 ns 19.5 ns 17.4 ns ns 13.2 ns 11.4 ns Temperature Table 4-5. Temperature Specifications Item Specification Operating temperature 32 F to 122 F (0 50 C) Performance temperature 41 F to 104 F (5 40 C) Start-Up Time Start-up time for DVSD / DVSE6800+ modules is approximately 10 seconds. DVSD / DVSE6800+ Installation and Operation Manual 27

40 Chapter 4: Specifications 28 DVSD / DVSE6800+ Installation and Operation Manual

41 Index Keywords A-G Adjustable parameters 19 Alarms 23 Applications 2 Back connectors see Back modules Back modules 4 5, 14 Changing parameter settings 22 Controls control types 16 understanding controls Descriptions LEDs module descriptions back modules 4 5 front modules 3 product description 2 Directives Restriction on Hazardous Substances xi Waste from Electrical and Electronic Equipment xii Features 2 3 Front modules 3 H-K Hardware versions, reading 22 Input specifications 26 Installation back modules 14 installing modules 14 jumpers power ratings 10 preparing modules 11 removing modules 14 required frames 14 unpacking modules 11 Introduction applications 2 main features 2 3 module descriptions back modules 4 5 front module 3 product description 2 signal flow diagrams 6 7 Jumpers controls control types 16 local control 17 remote control 17 understanding jumper controls P1 12, P2 13, P3 13, setting jumpers DVSD / DVSE6800+ Installation and Operation Manual 29

42 Index L-Q LEDs descriptions module specific 23 remote status 23 Local control jumpers 17 Manual information vii viii Module specific LEDs 23 Modules back modules 4 5 front modules 3 installing modules 14 LEDs preparing modules 11 removing modules 14 unpacking modules 11 Operating temperature 27 Operation alarms 23 jumper control types 16 LEDs local jumper controls 17 operating notes 19 parameters changing settings 22 parameter types 19 recalling settings 22 setting parameters reading hardware versions 22 software versions 22 remote jumper controls 17 understanding jumper controls Output specifications 26 Parameters adjustable 19 changing settings 22 parameter types 19 read-only 19 recalling settings 22 setting parameters Performance temperature 27 Power consumption specifications 27 Power ratings 10 Power up time 27 Preparing for installation 11 Product description 2 Propagation delay 27 R-Z Read-only parameters 19 Remote control jumpers 17 Remote status LEDs 23 Removing modules 14 Restriction on Hazardous Substances (RoHS) directive xi Safety compliances x RoHS directive xi standards x symbols x terms x WEEE directive xii Setting jumpers Shipping information ix Signal flow diagrams 6 7 Software versions, reading 22 Specifications input 26 output 26 power consumption 27 propagation delay 27 start-up time 27 temperature 27 Start-up time 27 Temperature specifications 27 Unpacking modules ix, 11 Waste from Electrical and Electronic Equipment (WEEE) directive xii 30 DVSD / DVSE6800+ Installation and Operation Manual