HYDRA2 DIGICO ORANGE BOX INTERFACE
|
|
- Margery Foster
- 6 years ago
- Views:
Transcription
1 HYDRA2 DIGICO ORANGE BOX INTERFACE calrec.com Putting Sound in the Picture
2 ORANGE BOX HYDRA 2 INTERFACE ORANGE BOX - FRONT VIEW The Orange Box provides audio format conversion between any two of the ten available interfaces using DMI (DiGiCo Multichannel Interface) modules The DMI-HYDRA 2 module interface for the Orange Box is shown right. It currently provides up to 56 Inputs and 56 Outputs when format converted to MADI using the DMI-MADI-B / DMI-MADI-C modules. DMI-HYDRA2 MODULE - FRONT PANEL The DMI-MADI module is connected to the DiGiCo console allowing I/O to be passed between Calrec and DiGiCo domains along with exchange of labels in either direction. The DMI bus interface carries up to 128 channels of audio in both directions and allows modules to be plugged in with power applied. Module Enclosure The DMI-HYDRA 2 Module fits into one of the module slots in the Orange Box. Hydra2 network connection A pair of front mounted SFP slots provide primary and secondary connections for a Hydra2 redundant network. Various fibre and copper SFP modules can be supplied for medium to long distances over Singlemode or Multimode fibre or CAT5e over Copper up to 90m. Both Primary and Secondary interfaces show connectivity and active data status using LED indication on the front of the modules. Fitting Modules Currently the DMI-HYDRA 2 Module has to be fitted in the right hand slot (DMI 2) of the Orange Box for sync purposes and as a consequence the DMI-MADI Module is fitted in the left hand slot (DMI 1) of the Orange Box. Calrec Programming The DMI-HYDRA 2 Module interfaces to the Hydra2 network via the Calrec US6235 H2M-PRO module which is plugged into connector CN7 on the DiGiCo P16189 Hydra 2 PCB. See DMI-HYDRA2 MODULE - BOARD VIEW on page 3. for module layout. The H2M-PRO can be seen in the Program Updater and Calrec Firmware and Software can be updated like any other Hydra2 I/O unit. Note: the Calrec software must be compatible with the DiGiCo software running on the DMI card. DiGiCo programming The DMI-HYDRA 2 Module contains DiGiCo Firmware and FPGA code. This is supplied by DiGiCo and is configured using the Orange Box Controller software for DMI card firmware and FPGA update. It is programmed via the USB REMOTE port on the front of the Orange Box. H2 Orange Box Interface
3 DMI-HYDRA2 MODULE - BOARD VIEW CALREC H2M PRO Module US6235 SECONDARY SFP PRIMARY SFP DiGiCo DMI-Hydra 2 Module P16189 Module Product Advisories Fitting the H2M PRO modules in the wrong host hardware, can cause FPGA failure. It is suspected that physical damage could be caused to the FPGA if they have the wrong flash image for the hardware they are being used in. due to incorrect PIN assignments. Unprotected serial debugging can also cause FPGA failure. A serial port is fitted for development purposes only. The header will be removed for production models. There little protection between the header and the FPGA. DMI BUS CONNECTOR General ESD handling. Care must be taken when handling and fitting the H2 Module and static protection wristbands are to be worn to prevent ESD failures. Note that this requires V3.2 software or later to work correctly. CALREC Putting Sound in the Picture 3
4 Orange Box Control Interface Once the USB cable is connected from a PC into the front of the Orange Box and the OrangeBoxController.exe file is running, the window shown on the right appears. This shows the control status of both DMI 1 & 2 (MASTER and SLAVE) modules in the Orange Box. ORANGE BOX CONTROLLER PAGE FOR DMI 1-HYDRA2 MODULE-CONTROL For the DMI-Hydra 2 Module in DMI 2 the control page shows H2 and also shows the internal module temperature, sample rate and sync source. Also on this page the user can select the COM port that the USB is communicating through. This page also allows the user to set the Hydra ID (HID) so that the ports on the Orange Box can be addressed over the HYDRA 2 network. Note that the User must select a HID that is not already in use on the network. The other module in DMI 1 is typically a DMI-MADI module connected to a DiGiCo product such as an SD9 which acts as the Master clock source and channel 57 of the MADI stream is used for Label Exchange and other control data. Orange Box Update Code Interface In order to update the code operating on the DiGiCo P16189 Hydra 2 PCB the user clicks on the Update Code page as shown on the right. ORANGE BOX CONTROLLER PAGE FOR DMI 1-HYDRA2 MODULE-UPDATE CODE This page again shows the card type but now shows the firmware and fpga versions that are running on the left column. If the firmware code digico_dmi.bin and the fpga code digico_h2_fpga.bit files are in the same folder as the OrangeBoxController.exe file then these available versions are shown on the right column. Clicking on the Update if required button when new code is available will program the devices on the DiGiCo P16189 Hydra 2 PCB. The individual Update Code and Update FPGA buttons allows the firmware and FPGA code to be altered should a rollback to a previous version be required. Orange Box Interface
5 Setting up the HID The DMI-HYDRA 2 Module like all other Hydra2 interfaces needs a HID so that the ports can be addressed. This is setup using the Orange Box Controller as seen on the previous page. DMI-HYDRA2 MODULE HARDWARE ID SET TO 1 Once received the Orange Box requires a reset (power off and on again) in order to be correctly addressed on the Hydra2 network. The image to the right shows when the Orange Box HID set to 1. It appears with a HID of 1 on the Hydra Options page and can be added to the required list ready to be made available to the Hydra Network. Console Compatibility Any Calrec consoles connecting to the Orange Box must be running version 3.2 software or later. Any DiGiCo consoles connecting to the Orange Box must be running a version of software that supports the Hydra 2 interface. Label Exchange The DMI-HYDRA 2 Module allows the exchange of labels between DiGiCo and Calrec systems. The image to the right shows the I/O ports page for this module in the Hydra2 network which are defined as Type= HydraModule. The Ports that have not had labels exchanged in this case all the Output ports are defined as HID number - Port Number, therefore is the first port on HID 01 i.e. the Orange Box. This goes up to for the last port on that box. When labels are exchanged as can be seen on the Input Ports, the label changes format to Socket:Desk:PortNo:PortLabel. DMI-HYDRA2 MODULE FRONT VIEW The image to the right shows as an example that these have come from Socket 3: on a SD9 DiGiCo console for Ports 1-56 and in the case highlighted Ports 13 and 14 are a Stereo Output Pair from the SD9 console labelled calrec i.e. 3:SD9 13: calrec has been exchanged as a label from the SD9 console. CALREC Putting Sound in the Picture 5
6 ( Iss.2)
DiGiCo Optocore V221 For SD Rack Optocore Operation
DiGiCo Optocore V221 For SD Rack Optocore Operation Issue C - July 2011 1-1 1-2 Contents 1.1 Introduction......4 1.1.1 System Overview......4 1.1.2 Opto V220 (DiGiRacks) and Opto V221 (SD Racks)......5
More informationUser Guide V1023+ October 2018
User Guide V1023+ October 2018 This guide is intended to be read in conjunction with the: SD Software Reference Manual and SD Software Reference Appendix available at: https://www.digico.biz/docs/about/manuals_1.shtml
More informationWAVES. MultiRack SETUP GUIDE V9.7
WAVES MultiRack SETUP GUIDE V9.7 1 Table of Contents 1. Overview... 3 2. Basic Requirements... 3 3. Software... 4 4. Required Waves Licenses... 4 5. Installing MultiRack... 5 MultiRack Native/SoundGrid
More informationSD12 SETTING A NEW STANDARD
SD12 SETTING A NEW STANDARD Dual Screen New LED METERS Integrated Light Bar HEADPHONE SUPPORT www.digico.biz 02 SD12 Introducing Project Vulcan... Introduction In 2015, DiGiCo launched its compact S-Series,
More informationDMI Waves. User Guide
DMI Waves User Guide TABLE OF CONTENTS Introduction... 3 About SoundGrid and the DMI Waves Audio Interface... 3 Typical Uses... 4 Native/SoundGrid Comparison Table... 6 1. Hardware and Connectors... 7
More informationUser Guide. for TAHOE 8622
User Guide for TAHOE 8622 TAHOE 8622 User Guide REV: 01 07/27/2017 PAGE 1 OF 37 TABLE OF CONTENTS 1. INTRODUCTION... 5 1.1 PRODUCT DESCRIPTION... 5 1.2 STANDARD FEATURES... 5 1.3 FUNCTIONAL DIAGRAM...
More informationUpgrade & Setup Waves SoundGrid V9.5 for DiGiCo
Upgrade & Setup Waves SoundGrid V9.5 for DiGiCo 1 Table of Contents 1. What Do I Need... 3 2. Connecting Your Console to the SoundGrid Network... 4 3. Disabling ReadyOn... 6 4. Extracting to USB Flash
More informationWAVES. MultiRack SETUP GUIDE V9.80
WAVES MultiRack SETUP GUIDE V9.80 1 Table of Contents 1. Overview... 3 2. Basic Requirements... 3 3. Software... 4 4. Required Waves Licenses... 4 5. Installing MultiRack... 5 MultiRack Native/SoundGrid
More informationVersion 4 Software. Version 4 - Supplement. Issue A, August 2007 for Version 4.0+ Software. D5 V4 Supp 1-1
Version 4 - Supplement Issue A, August 2007 for Version 4.0+ Software D5 V4 Supp 1-1 D5 V4 Supp 1-2 Contents 1.0 Introduction... 1-4 1.1 Hardware Configuration Options... 1-4 1.2 Audio Sync Options...
More informationIXIUM. DVR Mini Camera. User Manual
IXIUM DVR Mini Camera User Manual Contents Package Contents... 2 Before You Start... 2 Overview... 3 Controls... 4 SD Card Slot (TF)... 4 USB: Syncing and Charging... 4 Microphone... 4 On/Off... 4 Video
More informationEcho Digital Audio Corporation AudioFire 2 AudioFire 4 AudioFire 8 AudioFire 12 Release 4.6 for Mac OS X
Echo Digital Audio Corporation AudioFire 2 AudioFire 4 AudioFire 8 AudioFire 12 Release 4.6 for Mac OS X DISCLAIMER... 2 RELEASE INFORMATION... 2 SUPPORTED OPERATING SYSTEMS... 2 CHANGES... 3 KNOWN ISSUES...
More informationPreliminary Information
Preliminary Information S21: Rewriting the rule book Since it s inception in 2002, DiGiCo has always tried to innovate and push technology to deliver more in terms of flexibility and audio quality. There
More informationEcho Digital Audio Corporation AudioFire 2 AudioFire 4 AudioFire 8 AudioFire 12 Release for Mac OS X
Echo Digital Audio Corporation AudioFire 2 AudioFire 4 AudioFire 8 AudioFire 12 Release 3.1.1 for Mac OS X DISCLAIMER... 2 RELEASE INFORMATION... 2 SUPPORTED OPERATING SYSTEMS... 2 CHANGES... 3 KNOWN ISSUES...
More informationTABLE OF CONTENTS 1. INTRODUCTION 2. SPECIFICATION 3. HARDWARE INSTALLATION 6EX 1.1. PREFACE KEY FEATURES PERFORMANCE LIST...
6EX TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE...1-1 1.2. KEY FEATURES...1-1 1.3. PERFORMANCE LIST...1-2 1.4. BLOCK DIAGRAM...1-3 1.5. INTRODUCE THE Pentium II Processor & AGP...1-4 1.6 What is AGP?...
More informationPart Number: PCB-STM32-F4B1 (unpopulated PCB with Discovery module sockets, no other parts) STM32-F4B1 (assembled board, not presently available)
PCB-STM32-F4B1 Development baseboard for the STMicro Discovery-F4 module (STMicro part# STM32F4DISCOVERY) PCB Rev 1.00 shown. PCB Rev 1.20 has on-board RS232 drivers. Part Number: PCB-STM32-F4B1 (unpopulated
More informationHYDRA2 TECHNICAL Overview
HYDRA TECHNICAL Overview Gigabit Ethernet Networking calrec.com Putting Sound in the Picture Calrec Audio Ltd Nutclough Mill Hebden Bridge West Yorkshire England UK HX EZ Tel: + (0) Fax: + (0) Email: enquiries@calrec.com
More informationDANTE CERTIFICATION PROGRAM LEVEL 2
DANTE CERTIFICATION PROGRAM LEVEL 2 THE DANTE CERTIFICATION PROGRAM Level 2: Intermediate Dante Concepts Delivered in-person Larger systems (approx. 12 devices) Clocking options Understanding unicast &
More informationConnecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide
What is an igaging DigiMAG Scale? The igaging DigiMAG are digital linear scales that are easily connectable to the Caliper2PC interface. They consist of two parts, the encoder and the readout unit. The
More informationAL361A-EVB-A1. Multi-channel Video Processor EVB. Datasheet. (HDMI/AHD-to-HDMI) 2017 by AverLogic Technologies, Corp. Version 1.0
AL361A-EVB-A1 Multi-channel Video Processor EVB (HDMI/AHD-to-HDMI) Datasheet Version 1.0 INFORMATION FURNISHED BY AVERLOGIC IS BELIEVED TO BE ACCURATE AND RELIABLE. HOWEVER, NO RESPONSIBILITY IS ASSUMED
More informationINSTALLATION INSTRUCTIONS. ACB-100 Audio Control Board. This document describes the installation procedure for the ACB-100 Audio Control Board.
INSTALLATION INSTRUCTIONS MicroComm DXI -00 Audio Control Board. Intent & Scope This document describes the installation procedure for the -00 Audio Control Board. 2. Description The -00 Audio Control
More informationHDx TDM Record/Playback Option Guide
HDx TDM Record/Playback Option Guide Version 1.0 for D-Show Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support (USA) tel: 650 731
More informationURSA Mini SSD Recorder
Blackmagic is an optional module which attaches to the rear of URSA Mini Pro 4.6K. This recorder allows you to record footage, including 4.6K RAW files, to high capacity and inexpensive solid state drives,
More informationRemote Bus Extender Slave Module
Triguard SC300E MRB01XS Remote Bus Extender Slave Module (MRB01XS) Issue 4 October 2005 INTRODUCTION AND TECHNICAL DATA PURPOSE A Remote Bus Extender Slave Module MRB01XS (Figure 1-1 ) is located in each
More informationCPU fan has a power connector which needs to be connected to CPU fan power socket on your motherboard as shown on the image above.
The first thing you should do is unpack your ATX case. Take off the cover of your case so that you can access the inside. Place the case on a desk so that you are looking down towards the open case. Your
More informationKNJN I2C bus development boards
KNJN I2C bus development boards 2005, 2006, 2007, 2008 KNJN LLC http://www.knjn.com/ Document last revision on December 5, 2008 R22 KNJN I2C bus development boards Page 1 Table of Contents 1 The I2C bus...4
More informationDiGiCo S21 Getting Started
DiGiCo S21 Getting Started Version D for Software Version 1.0.1 Copyright 2015 Digico UK Ltd All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
More informationINTERMEDIATE DANTE CONCEPTS. Dante Certification Program Level 2
INTERMEDIATE DANTE CONCEPTS Dante Certification Program Level 2 LEVEL 2 TOPICS Clocking options in Dante Understanding latency in networks Dante Flows and Multicast Creating backup devices with Dante names
More information32 x 32 Modular Matrix Switch
32 x 32 Modular Matrix Switch The Modular Matrix Switch offers advanced access and real-time control of multiple local and remote A/V input devices and displays from a single chassis. The allows users
More informationBB-303 Manual Baseboard for TMCM-303
BB-303 Manual Baseboard for TMCM-303 Trinamic Motion Control GmbH & Co. KG Sternstraße 67 D 20357 Hamburg, Germany http://www.trinamic.com BB-303 Manual (V1.04 / Jul 9th, 2007) 2 Contents 1 Features...
More informationS2C K7 Prodigy Logic Module Series
S2C K7 Prodigy Logic Module Series Low-Cost Fifth Generation Rapid FPGA-based Prototyping Hardware The S2C K7 Prodigy Logic Module is equipped with one Xilinx Kintex-7 XC7K410T or XC7K325T FPGA device
More informationTechnical Documentation
SD-Card Adapter 2 Technical Documentation 1 Introduction SD-Card Reader The SD Memory Card provides application designers with a low cost mass storage device, implemented as a removable card, that supports
More informationGP-2301S/L->GP4000M Series Replacement Guidebook
GP-2301S/L->GP4000M Series Replacement Guidebook 1/45 Third Edition Jul. 2012 Copyright 2012.7 Digital Electronics Corporation. All Rights Reserved. Preface This guidebook introduces the procedures to
More informationSingle Channel Video Insert Unit with Bi-directional Data Channel for a Dual Redundant fibre ring
AMG3613DRSF Instruction Manual Single Channel Video Insert Unit with Bidirectional Data Channel for a Dual Redundant fibre ring The AMG3613DRSF is a standalone single channel video insert unit designed
More informationSMT166-FMC User Guide
Sundance Multiprocessor Technology Limited Product Specification Unit / Module Description: Unit / Module Number: Document Issue Number: Issue Date: Original Author: SMT166-FMC User Guide Revision History
More informationCOSMOS COLLECTOR X10 COSMOS X10 DATA COLLECTION AND REPORTING SYSTEM. User manual
User manual COSMOS COLLECTOR X10 COSMOS X10 DATA COLLECTION AND REPORTING SYSTEM - The data from the source device is collected with Modbus / TCP and S7 protocols via the X10 s Ethernet interface - The
More informationRKP08 Component List and Instructions
RKP08 Component List and Instructions PCB layout Constructed PCB RKP08 Scematic RKP08 Project PCB Page 1 Description The RKP08 project PCB has been designed to use PIC microcontrollers such as the Genie
More informationUSER GUIDE 1 of 26 STAGEGRID 4000 User Guide rev.01 abr-18
USER GUIDE 1 of 26 STAGEGRID 4000 User Guide rev.01 abr-18 SUMÁRIO About... 2 STAGEGRID 4000... 2 SoundGrid... 3 System Requirements... 3 Hardware... 4 Package Contents... 4 Rack Installation... 5 Setups...
More informationEVB-USB2250 User Manual Revision B
Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
More informationsolutions for teaching and learning
RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers
More informationHYDRA2 INSTALLATION MANUAL
HYDRA2 INSTALLATION NUAL Gigabit Ethernet Networking calrec.com Putting Sound in the Picture Calrec Audio Ltd Nutclough Mill Hebden Bridge West Yorkshire England UK HX7 8EZ Tel: +44 (0)422 84259 Fax: +44
More informationAL362B-EVB-A1. AHD-to-HDMI Quad Box Development Kit by AverLogic Technologies, Corp. Version 1.0
AL362B-EVB-A1 AHD-to-HDMI Quad Box Development Kit Version 1.0 INFORMATION FURNISHED BY AVERLOGIC IS BELIEVED TO BE ACCURATE AND RELIABLE. HOWEVER, NO RESPONSIBILITY IS ASSUMED BY AVERLOGIC FOR ITS USE,
More informationGLOG V2. Quick Guide
GLOG V2 Portable RS232 Serial Data Logger Quick Guide (c) 2015 - Geomatics USA, LLC GLOG V2 is a battery-powered compact device that logs data from RS232 serial devices. It records the logged bytes (in
More informationUSER GUIDE 1 INTRODUCTION 2 GENERAL DESCRIPTION. A) Mbed enabled MCU Board. B) Shield Board. Quad SPI Evaluation Kit
1 INTRODUCTION The from Winbond Electronics is consist of Mbed enabled MCU board which has an Arduino UNO R3 compatible terminal and Shield Board, Daughter Board. This document describes how to use the.
More informationVector 3D printer complete wire list including extruder PWA listing
Vector 3D printer complete wire list including extruder PWA listing Conventions Pin numbering for connectors It is normal practice in print circuit board (PCB) layout to denote pin 1 of a PCB mounted connector
More informationIXIUM. Spy Key Fob. User Manual
IXIUM Spy Key Fob User Manual Contents Package Contents... 2 Before You Start... 2 Overview... 3 Controls... 3 SD Card Slot (TF)... 3 USB: Syncing and Charging... 3 Power On/Off... 4 Turn On... 4 Turn
More informationHD/SD H.264 Capture Device (H.264 Video Encoder + Decoder) User s Manual Model 2226 Rev.A March 2010
HD/SD H.264 Capture Device (H.264 Video Encoder + Decoder) User s Manual Model 2226 Rev.A March 2010 Table of Contents TABLE OF CONTENTS...2 LIMITED WARRANTY...4 SPECIAL HANDLING INSTRUCTIONS...5 INTRODUCTION...6
More informationCHAPTER 1 Introduction of the tnano Board CHAPTER 2 tnano Board Architecture CHAPTER 3 Using the tnano Board... 8
CONTENTS CHAPTER 1 Introduction of the tnano Board... 2 1.1 Features...2 1.2 About the KIT...4 1.3 Getting Help...4 CHAPTER 2 tnano Board Architecture... 5 2.1 Layout and Components...5 2.2 Block Diagram
More informationUSB HD Audio/Video Codec Model 2263 Hardware Manual Ver October 2013
USB HD Audio/Video Codec Model 2263 Hardware Manual Ver.1.0.1 October 2013 Table of Contents LIMITED WARRANTY...3 SPECIAL HANDLING INSTRUCTIONS...4 INTRODUCTION...5 SYSTEM REQUIREMENTS...5 BLOCK DIAGRAM...6
More informationPLX USB Development Kit
870 Maude Avenue Sunnyvale, California 94085 Tel (408) 774-9060 Fax (408) 774-2169 E-mail: www.plxtech.com/contacts Internet: www.plxtech.com/netchip PLX USB Development Kit PLX Technology s USB development
More informationChipScope Inserter flow. To see the Chipscope added from XPS flow, please skip to page 21. For ChipScope within Planahead, please skip to page 23.
In this demo, we will be using the Chipscope using three different flows to debug the programmable logic on Zynq. The Chipscope inserter will be set up to trigger on a bus transaction. This bus transaction
More informationUpdate Instructions for V4.9.x.xxx V Vi1 and Vi2/4/6 consoles
Update Instructions for V4.9.x.xxx V1.1 22-08-2017 Vi1 and Vi2/4/6 consoles Note that although a common file is used for upgrading Vi1, 2, 4 and 6 consoles, the update procedure for Vi1 differs from the
More informationEcho Digital Audio Corporation AudioFire 2 AudioFire 4 AudioFire 8 AudioFire 12 AudioFire 8a AudioFirePre8 Gibson RIP Release 5.7.
Echo Digital Audio Corporation AudioFire 2 AudioFire 4 AudioFire 8 AudioFire 12 AudioFire 8a AudioFirePre8 Gibson RIP Release 5.7.1 for Mac OS X DISCLAIMER... 2 RELEASE INFORMATION... 2 SUPPORTED OPERATING
More informationPENTA. Routing and I/O. Professional I/O solutions and router infrastructure for analogue, digital and embedded audio systems
PENTA Routing and I/O Professional I/O solutions and router infrastructure for analogue, digital and embedded audio systems NTP Technology About NTP Technology NTP was founded in 1958. Since 2003 NTP Technology
More informationUser Manual. cmt-iv5 Startup Guide
User Manual cmt-iv5 Startup Guide v 2.2 JAN 8, 2016 Table of Contents Chapter1. Overview... 1 1.1. Specification... 1 1.2. Dimensions... 2 1.3. Ethernet port... 3 1.4. CR1225 battery... 3 1.5. Power connection...
More informationMADI-PC MADI RECORDING SYSTEM
MADI-PC MADI RECORDING SYSTEM USER MANUAL V1.0 1 P a g e Table of Contents INTRODUCTION... 3 IMPORTANT SAFETLY PRECAUTIONS... 4 General Safety... 4 Caution... 4 Power Safety... 5 Installation Notes...
More informationThis shield connects to Arduino with long-wire headers, which keeps the pin layout intact and allows another shield to be stacked on top.
Description SLD-000012 SIM900 GPRS/GSM shield for Arduino With the help of this shield and an SIM card, your Arduino could join your local mobile service provider s cell phone network. This shield allows
More informationQuick Start Guide. TWR-MPC8309 PowerQUICC Processor with Industrial Connectivity and Protocol Off-Load Engine TOWER SYSTEM
TWR-MPC8309 PowerQUICC Processor with Industrial Connectivity and Protocol Off-Load Engine TOWER SYSTEM -P23345-TWR-MPC8309-o1v6.indd 1 Get to Know the TWR-MPC8309 Display Header RS232 Header SD Slot (bottom)
More informationSTM32 F4xx Discovery Board Setup Guide
STM32 F4xx Discovery Board Setup Guide Audio Weaver November 2016 Copyright Information 2014 DSP Concepts, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express
More informationD IGIGRID MG B / MG O 1 1
1 1 Table of Contents Introduction 3 About SoundGrid and the DiGiGrid MGB and MGO Audio Interfaces 3 Using DiGiGrid MGB/MGO with a Console 6 1. Hardware and Connectors 7 2. Installation and Configuration
More informationTechnical Specifications: Dell OptiPlex GX150 System
Technical Specifications: Dell OptiPlex GX150 System Processor Microprocessor type Internal cache Intel Pentium III or Celeron microprocessor 32-kilobyte (KB) first-level (16-KB data cache; 16-KB instruction
More informationBlack Box Micro HD. User s Guide. Page 1 BrickHouse Security User s Guide
Black Box Micro HD User s Guide Page 1 BrickHouse Security User s Guide Black Box Micro HD The Black Box Micro HD is a fully functional and customizable video recording system in a compact case. Use the
More informationTABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE KEY FEATURES PERFORMANCE LIST BLOCK DIAGRAM...
TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE... 1-1 1.2. KEY FEATURES... 1-1 1.3. PERFORMANCE LIST... 1-3 1.4. BLOCK DIAGRAM... 1-4 1.5. INTRODUCE THE PCI - BUS... 1-5 1.6. FEATURES... 1-5 2. SPECIFICATION
More informationEVB-USB2240-IND User Manual Revision B
Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
More informationWBD-222. Hardware Manual. Revision September Copyright 2010 WILIGEAR
WBD-222 Hardware Manual Revision 1.2 15 September 2010 Copyright 2010 WILIGEAR www.wiligear.com Copyright 2010 WILIGEAR This user s guide and the software described in it are copyrighted with all rights
More informationChapter 3: Computer Assembly
Chapter 3: Computer Assembly IT Essentials v6.0 ITE v6.0 1 Chapter 3 - Sections & Objectives 3.1 Assemble the Computer Build a Computer. 3.2 Boot the Computer Explain how to verify BIOS and UEFI settings.
More informationBlack Box HD. User s Guide. BrickHouse Security User s Guide
Black Box HD User s Guide Page 1 Black Box HD The Black Box HD is a fully functional and customizable video recording system in a compact case. Use the preset recording mode, or program custom settings
More informationPCM-4153-A2 PC/104+ SBC w/amd LX800, VGA, LCD, Dual LAN, USB 2.0, On-board Flash and Memory Startup Manual
PCM--A PC/0+ SBC w/amd LX800, VGA, LCD, Dual LAN, USB.0, On-board Flash and Memory Startup Manual Packing List Specifications Before you begin installing your card, please make sure that the following
More informationMMX Enhanced. 586 GXM-AV Main Board. Trademarks and / or Registered trademarks are the properties of their respective owners.
586 GXM-AV Main Board Trademarks and / or Registered trademarks are the properties of their respective owners. User s Manual Version 1.1 The Information presented in this publication has been carefully
More informationThe watchdog is connected to the internal USB header and reset switch header on the majority of motherboards.
BitBox Product Description The BitBox USB watchdog receives commands from PC application software via a virtual COM port that tell it if the PC is running. When there has been no command from the PC for
More informationTABLE OF CONTENTS 1. INTRODUCTION 2. SPECIFICATION 3. HARDWARE INSTALLATION 6EM 1.1. PREFACE KEY FEATURES PERFORMANCE LIST...
6EM TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE...1-1 1.2. KEY FEATURES...1-1 1.3. PERFORMANCE LIST...1-2 1.4. BLOCK DIAGRAM...1-3 1.5. INTRODUCE THE Pentium II Processor & AGP...1-4 1.6 What is AGP?...1-6
More informationTABLE OF CONTENTS 1. INTRODUCTION 2. SPECIFICATION 3. HARDWARE INSTALLATION 6BA
6BA TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE...1-1 1.2. KEY FEATURES...1-1 1.3. PERFORMANCE LIST...1-2 1.4. BLOCK DIAGRAM...1-3 1.5. INTRODUCE THE Pentium II / III Processor...1-4 1.6. What is AGP?...1-5
More informationT Z JA WARNING: To avoid bus contention, plug in only ONE board (Ozy or Janus) when running loop-back tests in Test Fixture 1.
Ozy/Janus Test Plan v5.0 5/9/2007 Copyright 2007 Scotty Cowling, WA2DFI 1 Serialization Boards will be serialized per the following: T Z JA 1-001 T=TAPR build sponsor Z=Zephyr build engineering Serial
More informationSTANDALONE INTERFACES USB-DMX 512 & 1024 CHANNELS V.1.1
STANDALONE INTERFACES USB-DMX 512 & 1024 CHANNELS V.1.1 SUMMARY Hardware technical specifications... 3 Front Face of the 512 / 1024 channels interfaces... 4 Side Faces of the 512 / 1024 channels interfaces...
More informationHDMI over IP Extender HP100FT HDMI KVM, USB, RS232, IR over IP - Transmitter HP100FR HDMI KVM, USB, RS232, IR over IP Receiver
HDMI over IP Extender HP100FT HDMI KVM, USB, RS232, IR over IP - Transmitter HP100FR HDMI KVM, USB, RS232, IR over IP Receiver HP100FT-front view HP100FR-front view HP100FT-rear view HP100FR-rear view
More informationDIGIGRID MGR. Table of Contents
1 1 Table of Contents Introduction 3 About SoundGrid and the DiGiGrid MGR Audio Interface 3 Using DiGiGrid MGR with a Console 6 1. Hardware and Connectors 7 2. Installation and Configuration Overview 9
More informationTABLE OF CONTENTS 1. INTRODUCTION 2. SPECIFICATION 3. HARDWARE INSTALLATION. Table Of Contents 1.1. PREFACE KEY FEATURES...
Table Of Contents TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE...1-1 1.2. KEY FEATURES...1-1 1.3. PERFORMANCE LIST...1-2 1.4. BLOCK DIAGRAM...1-3 1.5. INTRODUCE THE Pentium II Processor & AGP...1-4 1.6.
More information(The hard drive is in a cage that needs to be removed, and there is a converter covering the pins.)
Sabrent USB-DSC8 3.0 USB to SATA/IDE Hard Drive Adapter 2.5 Notebook IDE Hard Drive 1. Connect the short 2.5 IDE connector from the Sabrent adapter to the pins on your 2.5 Hard Drive. Note the keyed pin
More informationModel UD2A-EDID DVI Extender with EDID Management, Serial & GUI Control
Model UD2A-EDID DVI Extender with EDID Management, Serial & GUI Control UMA1148 Rev D Copyright 2008. Hall Research, Inc. All rights reserved. 1163 Warner Ave Tustin, CA 92780, Ph: (714)641-6607, Fax (714)641-6698
More informationUs U er e r G u G i u de d AX A 3 X DA D N A T N E T I/O / O Car a d r d
User Guide AX32 DANTE I/O Card IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS WARNING when using electric products, basic precautions should be followed, including the following: Read all
More informationVersatile configuration options
HDMI and USB over IP Distribution Kit - 1080p StarTech ID: ST12MHDLANU This HDMI over IP kit lets you extend an HDMI signal, as well as four USB peripheral device connections, over your network. You can
More informationSMT943 APPLICATION NOTE 1 APPLICATION NOTE 1. Application Note - SMT372T and SMT943.doc SMT943 SUNDANCE MULTIPROCESSOR TECHNOLOGY LTD.
APPLICATION NOTE 1 Application Note - SMT372T + SMT943 SMT943 SUNDANCE MULTIPROCESSOR TECHNOLOGY LTD. Date Comments / Changes Author Revision 07/07/10 Original Document completed CHG 1 Date 13/05/2010
More information256 MB RAM. 256 MB 32 bits RISC Cortex-A8 600MHz SD Card Slot. N/A USB Host. N/A USB Client
User Manual V1.0.0 Table of Contents Overview... 1 1.1. Specification... 1 1.2. Dimensions... 2 1.3. Connector pinouts... 3 1.4. Restoring factory default... 3 1.5. LED indicator... 3 1.6. CR1225 battery...
More informationQuick Start XLe Source Expansion Kit
Quick Start XLe Source Expansion Kit Caution: Before touching the supplied audio card, ground yourself by touching an unpainted metal surface. While working on your computer you should periodically touch
More informationAccessories Bus Terminals
Accessories s Connectors Lightbus Z1000 Z1010 Z1020 standard connector for 1,000 µm plastic fibre standard connector for 200 µm PCS fibre coupling for Z1000 PROFIBUS ZB3100 ZB3101 ZB3102 ZS1031-3000 ZS1031-3500
More informationPI Scanner User Guide
PI Scanner User Guide Table of Contents 1. Highlights 2. Overview 3. Installation 3.1. PI Scanner Software Installation 3.2. USB to Serial Interface Board Installation 3.3. Programming the PI Scanner IP
More informationVGA KVM Extender CATVision 7.2
CATVision KVM Extender Extender systems to bridge IT-distances Leading the way in digital KVM The company Leading the Way in digital KVM Guntermann & Drunck GmbH has been established in 1985 and is named
More information4 Channel Video Insert Unit with Ethernet for a Dual Redundant Single Fibre Ring
AMG3741EDRSF Instruction Manual 4 Channel Video Insert Unit with Ethernet for a Dual Redundant Single Fibre Ring The AMG3741EDRSF is a standalone four channel video insert unit designed to transmit 4 video
More informationTECHNICAL BULLETIN. Audio Noise in Systems mixing older 8-port Cards with TRIBUS / MADI / AIO-16s
TECHNICAL BULLETIN 11-Oct-2013 Audio Noise in Systems mixing older 8-port Cards with TRIBUS / MADI / AIO-16s Issue Severity: High: URGENT Immediate Action Required Medium: Bosch Security Systems, Inc.
More informationDVI KVM Extender FIBREVision 7.3
FIBREVision KVM Extender Extender systems to bridge IT-distances Leading the way in digital KVM The company Leading the way in digital KVM Guntermann & Drunck GmbH has been established in 1985 and is named
More informationData sheet GCM MOD GMM EC.1 Communications module Modbus for GMM EC
Data sheet GCM MOD GMM EC.1 Communications module Modbus for GMM EC ERP no.: 5206415 GCM MOD GMM EC.1 www.guentner.de Page 2 / 15 Contents 1 GCM MOD GMM EC.1...3 1.1 Functional description...3 1.2 Connections...
More informationHD/SD H.264 Capture Device (SDI HD/SD H.264 Video Encoder) User s Manual Model 2224 Rev.0 September 2013
HD/SD H.264 Capture Device (SDI HD/SD H.264 Video Encoder) User s Manual Model 2224 Rev.0 September 2013 Table of Contents TABLE OF CONTENTS...2 LIMITED WARRANTY...4 SPECIAL HANDLING INSTRUCTIONS...5 INTRODUCTION...6
More information1. Introduction 1.1.Product Overview
1. Introduction 1.1.Product Overview The multi-function panel is a new extreme 3-module product comes with multi-slot card reader, thermal indicator and multi I/O panel, user able to install in standard
More informationSmartEQ Pro+ with Go2Nova 8408 Hand Controller Firmware Upgrade
SmartEQ Pro+ with Go2Nova 8408 Hand Controller Firmware Upgrade The firmware of a SmartEQ Pro+ main board and Go2Nova 8408 hand controller can be upgraded by a customer. Please check ioptron s website,
More informationSpecification additions/changes for Yamaha CL5/CL3/CL1 V1.02
Specification additions/changes for Yamaha CL5/CL3/CL1 V1.02 Thank you for choosing a Yamaha CL series CL5/CL3/CL1 Digital Mixing Console. With the CL series firmware version 1.02, some specifications
More informationTABLE OF CONTENTS 1. INTRODUCTION 2. SPECIFICATION 3. HARDWARE INSTALLATION 6BXDS 1.1. PREFACE KEY FEATURES...1-1
6BXDS 1. INTRODUCTION TABLE OF CONTENTS 1.1. PREFACE...1-1 1.2. KEY FEATURES...1-1 1.3. PERFORMANCE LIST...1-2 1.4. BLOCK DIAGRAM...1-3 1.5. INTRODUCE THE Pentium II Processor...1-4 1.6. What is AGP?...1-6
More informationminidsp Kit USER MANUAL V1.5 Revision Description Date V1.0 User manual Initial version
minidsp Kit USER MANUAL V1.5 Revision Description Date V1.0 User manual Initial version 15-12-2009 V1.1 Layout re-organization Modification on synchronization process Added section about PEQ 10-02-2010
More information4.1 Design Concept Demonstration for Altera DE2-115 FPGA Board Demonstration for Cyclone III Development Board...
CONTENTS CHAPTER 1 INTRODUCTION OF THE AHA-HSMC... 1 1.1 Features...1 1.2 About the KIT...2 1.3 Getting Help...3 CHAPTER 2 AHA CARD ARCHITECTURE... 4 2.1 Layout and Components...4 2.2 Block Diagram of
More informationPart Number Density Product Type Operation Temperature. W25Q80NESNIG 8Mb 1.2V Serial NOR Flash Memory Industrial (-40 C to +85 C)
1. INTRODUCTION This describes how to use the. The mbed enabled MCU board, which has an Arduino UNO R3 compatible terminal, is used in this description. 2. GENERAL DESCRIPTION The from Winbond Electronics
More informationDigital Sample-to-Memory
Digital Sample-to-Memory The Digital Sample-to-Memory option for Synclavier PowerPC is a PCI hardware module and a collection of software drivers that let you record digital audio directly into the Sample-to-Memory
More informationHDMI and USB over IP Distribution Kit p
HDMI and USB over IP Distribution Kit - 1080p Product ID: ST12MHDLANU This HDMI over IP kit lets you extend an HDMI signal, as well as four USB peripheral device connections, over your network. You can
More information