Matrix Trident installation tutorial (v1.1) SLIM XBOX360 TUTORIAL
|
|
- Roger Fisher
- 6 years ago
- Views:
Transcription
1 Matrix Trident installation tutorial (v1.1) SLIM XBOX360 TUTORIAL This tutorial will guide you in the process of installing your Matrix Trident into a Slim or Fat Xbox360 with 16Mb NAND. Once correctly installed the Trident will offer you three independent banks of NAND that can behave exactly like the original one and can be flashed with any SPI NAND programmer like the Matrix NAND programmer. Using the external switch it will than be possible to select which NAND to activate at the boot of the Xbox360. Matrix Trident also implements a reset feature that resets the Xbox360 every time a new bank is selected thus ensuring a corruption free NAND if bank switching is done when the Xbox360 console is already on. Users can keep their original NAND safe into the machine, while using the external NAND banks to load a custom Dashboard/Kernel or alternative OS in any of the other two banks. The possibilities are endless. The Trident is a stand alone NAND expansion solution, meaning it can work with ANY Glitch chip available on the market to date. Using it with a Glitcher II chip is of course highly suggested!
2 REQUIREMENTS: Required Hardware: A SLIM Xbox360 with a Glitch chip installed and working (Matrix Glitcher II suggested). Matrix NAND Programmer or any other USB SPI NAND programmer to dump/flash the NAND banks. Soldering Material. Required Software: NandPro V 2.0e o NandPro V 3.0 or any other software compatible with your SPI NAND programmer.
3 INSTALLATION PROCEDURE: 1) Open the Xbox 360 and remove the motherboard from the inside. There are many online tutorial to guide you through this steps. 2) Prepare the Trident as follows: a) Place the Black and Blue stickers on top of the connectors: b) Insert the black 4 pins cable for the external switch connector. Insert the white 4 pins cable (only if you have a Matrix Glitcher II and want to disable the glitcher when the original NAND is selected)
4 3) Carefully place the Matrix Trident in position so that all 16 red soldering points are aligned with the corresponding pads on the Xbox360 motherboard. Before soldering, make sure to secure the Trident with some tape to avoid it moving around. We suggest to begin by soldering the point in the lower left corner (the one closet to the number zero on the Trident pcb). Once this is done, make sure that the pcb seats flat on the surface of the motherboard and that the alignment with the other pads is still correct. You can then proceed to solder all the other points until all 16 pads are done.
5 4) Using the installation diagram, finish soldering the B and H wires to the corresponding points on the Xbox360 motherboard. 5) If you are using a Matrix Glitcher II, connect the white 4 pins cable.
6 6) If you have an old Matrix Glitcher I or a different glitcher brand you can use the Trident onboard power switch to disable the glitcher when the original NAND is selected. Remove the wire powering your glitcher pcb (vcc/3v3) and use the following diagram to connect the Trident to your glitcher s vcc/3v3 pad.
7 7) Put the mainboard back in the cage, and proceed to close the XBOX. When closing the box, also use some duct tape to protect the flat cable from cuts of the metal cage to avoid any damage. Leave out the screw in the corner to not put too much pressure on the cable. The best way to bring outside the black flat cable is to have it pass from the back of the the Xbox 360. Here are some pictures to better explain:
8 You can than position the external switch it in any place you like, on the top or side or back of the Xbox360, there is plenty of cable to choose the position you prefer best. Use the piece of double adhesive tape that you will find inside the bag to fix into the chosen position the external switch. Congratulation, your Matrix Trident is now installed and ready to use.
9 HOW TO SELECT THE DIFFERENT NAND BANKS. The external switch of the Trident has three positions and three leds on board. With the switch totally on the right (GREEN LED), the ORIGINAL NAND is selected. In this position any glitcher chip connected to the Trident (white flat cable in case of Glitcher II or Y pad for any other glitcher chip) is also disabled. The Xbox360 will behave like an original untouched console. With the switch in the middle position (BLUE LED), Trident NAND bank 1 is activated. With the switch all to the left position (RED LED), Trident NAND bank 2 is activated. Please note that every time a different bank is selected with the external switch, the Trident will also reset the Xbox360 console to avoid any data corruption on the selected bank. We always suggest to change NAND bank from the standby state. Once a bank is selected, it can be read and written to just like the original onboard nand. As a first step it is suggested to connect your SPI programmer, place the switch in the GREEN position and make a backup copy of your original NAND. Do the same for the BLUE and RED banks on your Matrix Trident (these are currently blank but a backup is needed to preserve any bad block information that might be present on those banks). Once this is done you can use each different bank like an independent NAND. Please refer to the software usage manual for full instructions.
Cygnos360 V2 Installation Manual
VERSION 1.0. - OKTOBER, 2009 www.cygnos360.com Contents: 1. What you need...2 1.1. Tools...2 2. Preparation...3 2.1. Preparing the solder points...3 3. Installing in your Xbox360...4 3.1. Installing the
More informationCygnos360 V2 Installation Manual
VERSION 1.03 - JANUARY, 2010 www.cygnos360.com Contents:... 1 1. What you need... 2 1.1. Tools... 2 2. Preparation... 3 2.1. Preparing the solder points... 3 3. Installing in your Xbox360... 4 3.1. Installing
More informationCygnos360 V2 Installation Manual
Cygnos360 V2 Installation Manual VERSION 1.04. - MARCH, 2010 www.cygnos360.com Contents: Cygnos360 V2 Installation Manual... 1 1. What you need... 2 1.1. Tools... 2 2. Preparation... 3 2.1. Preparing the
More informationThis tutorial was written by Team Xecuter. If you use anything from this tutorial please give credits and also a direct link to this page. Also if we have made any mistakes or left anything out please
More informationOpen Desktop WorkStation System Components Items Labeled in RED are ESD Sensitive
Page 1 of 21 Open Desktop WorkStation System Components Items Labeled in RED are ESD Sensitive Back Plane Pegasos IDE Cable Hard Drive Video Card G4 CPU IDE Cable CDROM Page 2 of 21 Remove top of case
More informationApplication Note: AN0106. On-Board SPI Programming with Dediprog tools: End User Version
4F., No.7, Ln. 143, Xinming Rd., Neihu Dist., Taipei City 114, Taiwan Application Note: AN0106 On-Board SPI Programming with Dediprog tools: End User Version (This document is provided to help users who
More informationOpenSprinkler v2.2u Build Instructions
OpenSprinkler v2.2u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationTHE LITE-ON DG16D5S AND HITACHI DLN10N 0500/0502* SOLUTION FROM THE MATRIX TEAM
QUICK INSTALL GUIDE FOR MATRIX CRYPTOCOP ADDON + FREEDOM LITE PCB: THE LITE-ON DG16D5S AND HITACHI DLN10N 0500/0502* SOLUTION FROM THE MATRIX TEAM BEFORE YOU BEGIN This solution provides the option to
More informationPanasonic DMP-BD60/BD80
Panasonic DMP-BD60/BD80 Region switching guide With the mod. chip fitted the player will automatically play DVD's from all regions (1-6), but for Blu-ray disc playback the region must be manually selected.
More informationColecovision 5v Memory Mod Installation
Colecovision 5v Memory Mod Installation The Colecovision suffers from common failure points: the power supply, power switch, and 4116 DRAM. The power supply suffers from poor soldering, the power switch
More informationReflowing Xbox 360 Motherboard
Reflowing Xbox 360 Motherboard Reflow the solder on your Xbox 360's motherboard. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Use this guide to reflow the solder
More informationPanasonic DMP-BD35/BD55
Panasonic DMP-BD35/BD55 Region switching guide With the mod. chip fitted the player will automatically play DVD's from all regions (1-6), but for Blu-ray disc playback the region must be manually selected.
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationZero2Go. User Manual (revision 1.03) Wide Input Range Power Supply for Your Raspberry Pi. Copyright 2017 UUGear s.r.o. All rights reserved.
Zero2Go Wide Input Range Power Supply for Your Raspberry Pi User Manual (revision 1.03) Copyright 2017 UUGear s.r.o. All rights reserved. Table of Content Product Overview... 1 Product Details... 3 Package
More informationOpenSprinkler v2.1u Build Instructions
OpenSprinkler v2.1u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationThank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide. For Use on all Model 2 Consoles with SANYO Drives ONLY
Thank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide For Use on all Model 2 Consoles with SANYO Drives ONLY *NOTE* When attempting to play a backup after installation is done,
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationXeLL-HACK (XBR) XENON-ZEPHYR-FALCON-OPUS-JASPER
XeLL-HACK (XBR) XENON-ZEPHYR-FALCON-OPUS-JASPER In this tutorial I will describe how to flash your console with the XeLL-Homebrew-Hack / XBox-Rebooter-Kernel. 1.Which Xbox Revision do I have? By looking
More informationParts List: Assembly Instructions:
My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord
More informationPage
Page 2... 3... 4... 5-6... 7... 8... 9-11... 12... 13... 14-15... Index, Foreword Product Overview Preparation for Assembly Installing the Motherboard Installing Case Fan & Optional IRRC Wiring Diagram
More informationAnker Vertical Mouse - Fix Optical Unit (fixiing Wobbling Mouse Pointer) Replacement
Anker Vertical Mouse - Fix Optical Unit (fixiing Wobbling Mouse Pointer) Replacement Anker Vertical Mouce (98ANWVM-BA). If you encounter an moving mouse pointer just by holding up the mouse and "shaking"
More informationConnecting igaging DigiMAG Scales to the Caliper2PC Interface A step by step Guide
What is an igaging DigiMAG Scale? The igaging DigiMAG are digital linear scales that are easily connectable to the Caliper2PC interface. They consist of two parts, the encoder and the readout unit. The
More informationHow to Assemble a Desktop PC
How to Assemble a Desktop PC By Taylor Koch iii Table of Contents Introduction to Building a Desktop PC... 1 Preparation and Precautions... 3 PC Parts... 3 Basic Tools... 3 Safety Precautions... 3 Installing
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationPage. Foreword. We sincerely hope that you enjoy using our product! P2 - INDEX
Page 2... Index, Foreword 3... Product Overview 4... Preparation for Assembly 5-6... Installing the Motherboard 7... Installing the Passive CPU Cooler 8... Fitting the HDD/ODD 9... PCB Wiring Diagram 10...
More informationXbox 360 Motherboard Replacement
Xbox 360 Motherboard Replacement Motherboard replacement. Redigido por: Walter Galan ifixit CC BY-NC-SA pt.ifixit.com Página 1 de 29 INTRODUÇÃO Use this guide to completely strip down your motherboard.
More informationEmatic Genesis Screen Replacement
Screen replacement for the Ematic Genesis tablet Written By: Justin Rohrman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION If the screen is cracked or damaged it may need to be replaced. This
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationPCS-2. Universal Infrared Remote PC Power Switch
PCS-2 Universal Infrared Remote PC Power Switch General Description The PCS-2 allows you to switch your PC / HTPC on-off with your existing TV or universal infrared (IR) remote. Single button mode allows
More informationCPU fan has a power connector which needs to be connected to CPU fan power socket on your motherboard as shown on the image above.
The first thing you should do is unpack your ATX case. Take off the cover of your case so that you can access the inside. Place the case on a desk so that you are looking down towards the open case. Your
More informationglitchscience.com Alesis HR-16 Mod Guide
1 Table of Contents Safety... p.3 PCB Revision Illustrations... p.4-5 Battery Replacement Procedure... p.6-11 HR-16 to HR-16B Conversion Procedure... p.12-17 HR-16 / HR-16B Blue LCD Installation... p.18-22
More informationThank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide. For Use on all Model 1 Consoles Only
Thank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide For Use on all Model 1 Consoles Only *NOTE* When attempting to play a backup after installation is done, make sure to have
More informationTwisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual
Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual Document Part #: 040-0271-01 Rev. C Your cabinet has a new design with a Sintra Marquee, stand-alone
More informationUpgrading Einstein Using the Einstein 1.5 Upgrade Kit. An EAB board with Production Einstein 1.5 Software EEPROM Chips.
TECHNICAL BULLETIN Upgrading Einstein Using the Einstein 1.5 Upgrade Kit This bulletin explains how to use the components of the CPC Upgrade Kit to upgrade a pre-1.5 version Einstein unit to the latest
More informationEmax SE SCSI Port Emax Plus Retrofit Instructions (Fl360)
Emax SE SCSI Port Emax Plus Retrofit Instructions (Fl360) Tools needed: Exacto Knife, Vacuum Desoldering Tool, Soldering Iron, Solder, Phillips Screwdriver, Needle Nose Pliers, 1/2 Nut Driver, 5/8 and
More informationXbox 360 Optical Drive Replacement
Xbox 360 Optical Drive Replacement Optical drive replacement. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION This guide only demonstrates how to remove the optical
More informationS16T user guide. Origen
S16T user guide Origen S16T user guide Thank you for purchasing this Origen ae htpc enclosure. We recommend that you read this user guide thoroughly before installation. Origen ae has rapidly grown to
More informationINSTALLATION GUIDE FOR UBI SENSOR FRAME
INSTALLATION GUIDE FOR UBI SENSOR FRAME Ubi Interactive Inc. Contents INTRODUCTION... 2 WHAT IS IN THE PACKAGE... 2 HOW TO SET UP HARDWARE... 2 INTERACTION... 6 SETTING UP UBI APPS... 7 INTRODUCTION Ubi
More informationMAKE SURE TO TURN OFF YOUR TRS-80 BEFORE ATTACHING NEWKEY/80 KEYBOARD RIBBON CABLE AND POWER CABLE.
NEWKEY/80 User's Guide v1.4 TRS80 Keyboard Adapter 12/10/2018 Plaid Vest Software, LLC. www.plaidvest.com/newkey80 IMPORTANT NOTE: MAKE SURE TO TURN OFF YOUR TRS-80 BEFORE ATTACHING NEWKEY/80 KEYBOARD
More informationAladdin XT installation Guide
Aladdin XT installation Guide Thank you for purchasing! To begin the installation, you will need to first remove the motherboard from the Xbox. Step 1 Installing the Pin Header: Now that you have the motherboard
More informationihome ih9 Infrared Receiver Replacement
ihome ih9 Infrared Receiver Replacement Replace the chip for receiving data from the remote control Written By: Charlie Ross ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION To complete this
More informationinstructions for assembly Hard Drive & Hard Drive Doubler Parts list 2* hard drive doubler 12* 6-32 UNC panhead 1 x body 4* 6-32 hex standoff
Cubit 5 instructions for assembly Bag 3 Hard Drive & Hard Drive Doubler Parts list 2* hard drive doubler 12* 6-32 UNC panhead 1 x body 4* 6-32 hex standoff 1 x front plate 1 x back plate 1 x top tray 1
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationWasabi 360 Ultra User Guide
Wasabi 360 Ultra User Guide For firmware v1.2, document revision 0, 25/2/2012 Introduction Wasabi 360 Ultra the ultimate ODDE (Optical Disc Drive Emulator), allows you to emulate you Xbox 360 s optical
More informationapple Service Source Apple Cinema Display 22" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema Display 22" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema Display 22" LCD (ADC) 2003 Apple Computer,
More informationWritten By: StacyAnn Brown
Microsoft Surface Pro 4 Battery Replacement Removing and replacing Microsoft Surface Pro 4 Battery. Written By: StacyAnn Brown ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION How to remove
More informationDarksoft s Sega ST-V Multicart
Game selector for Darksoft s Sega ST-V Multicart Version 1.0 "1 Selector board Game selector board consists of Arduino Nano clone for the logic, two row LCD screen with buttons and main PCB with connectors
More informationWritten By: Andrew Bookholt
PlayStation 3 Slim Heat Sink Replacement Replace your PS3 Slim's heat sink and its integrated fan shroud. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION Use this
More informationWiring Classic MIDI Works Console Toe-Studs to the Classic MIDI Works Pedal Board (MKSC-4A encoder)
Wiring Classic MIDI Works Console Toe-Studs to the Classic MIDI Works Pedal Board (MKSC-4A encoder) The Classic MIDI Works Console Table comes with 16 brass toe-studs mounted 8 each on a slanted left and
More informationimac Intel 27" Retina 5K Display CPU Replacement
imac Intel 27" Retina 5K Display CPU Replacement Replace or upgrade the CPU in your imac Intel 27" Retina 5K Display. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION
More informationCRESCENDO /PB G3. Processor Upgrade Card for Macintosh PowerBook 1400 Series Computers. Quick Start Guide for Crescendo/PB G3
CRESCENDO /PB G3 Processor Upgrade Card for Macintosh PowerBook 1400 Series Computers G3 Macintosh PowerBook and Operating System Compatibility The Crescendo/PB G3 processor upgrade card is compatible
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationimac Intel 21.5" EMC 2389 Stand Replacement
imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION
More informationSamsung Galaxy Note5 Teardown
Written By: Sophia ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION Witrigs provides all of Samsung Galaxy Note 5 replacement parts. [video: https://www.youtube.com/watch?v=fyetted5ghk] TOOLS:
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationRAIDTech USER S MANUAL. Revised October 3, Features
RAIDTech USER S MANUAL Revised October 3, 2006 Features Simple, hardware-based RAID (levels 0 or 1) On-the-fly data protection: RAID 1 makes backing up as painless as possible. The data is mirrored in
More informationARGON2 User Manual 4th generation WII modchip Updatable via Internet Argonchannel legal software Solderless Control on data bus.
ARGON2 User Manual 4th generation WII modchip Updatable via Internet Argonchannel legal software Solderless Control on data bus. Quick Start Guide Release 1.0 Document Version 1.4 10/02/2009 Legal Notes
More informationSTANDALONE WALL INTERFACE USB-DMX SLIM V.1.5.0
STANDALONE WALL INTERFACE USB-DMX SLIM V.1.5.0 SUMMARY Hardware Technical Specifications... 2 General pinout and device's connector... 3 Bottom face of the interface... 3 15 external Contacts wiring and
More informationNvidia Shield Tablet K1 Micro USB Port Replacement
Nvidia Shield Tablet K1 Micro USB Port Replacement This is a guide for the removal and replacement of the Micro USB Port. Written By: Ryan Butler ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION
More informationFloppy Disk To USB. Converter Installation and. Operation Manual
Floppy Disk To USB Converter Installation and Operation Manual Kit Price $125.00 Plus Shipping Why Should I Change My Floppy Drive To A USB Drive? You won't ever need floppies anymore and yet you'll be
More informationXNUCLEO-F030R8, Improved STM32 NUCLEO Board
XNUCLEO-F030R8, Improved STM32 NUCLEO Board STM32 Development Board, Supports Arduino, Compatible with NUCLEO-F030R8 XNUCLEO-F030R8 Features Compatible with NUCLEO-F030R8, onboard Cortex-M0 microcontroller
More information3) Mount one screw and nut on bracket.
The following instructions and pictures are provided to assist you with the installation of the EVGA GTX 1080/GTX 1070 FTW Hybrid Cooling Kit on compatible GTX 1080/GTX 1070 FTW graphics cards. Please
More informationHGR-2488 Prism Installation Instructions
HGR-2488 Prism Installation Instructions These installation instructions are applicable to the following models: TASCAM 2488 MK1 (original model) TASCAM 2488 MK II TASCAM 2488 NEO Page 1 of 8 Important
More informationGetting to know your Cronus device
Getting to know your Cronus device 1. INPUT (USB Receptacle Type A) Connector for wired game controllers or wireless receivers. 2. OUTPUT (USB Plug Type A) To connect the Cronus device on game consoles
More informationMaxxyz Compact Retrofit Kit Installation Guide
Maxxyz Compact Retrofit Kit Installation Guide Introduction The new M-Series software and the Windows 7 Embedded OS require that the Maxxyz Compact and Cerebrum modules are upgraded to 2 GB RAM. This Retrofit
More informationMACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS
MACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS List of tools and materials needed: Modchip, flexible LED add-on board, 6 tac switches Microsoft wireless CG2 controller Soldering iron and thin
More informationATTiny84/85 AVR adapter kit building and usage instructions
ATTiny84/85 AVR adapter kit building and usage instructions Version date Author Comments 1.0 25/06/2013 Boris du Reau Initial version 1.1 30/09/2013 Boris du Reau Updated document 1 Goal... 2 2 Kit content...
More informationVersion: 1.0 Public Effective from: 22 August 2017
Introduction TiVo units sold in Australia and New Zealand are being discontinued by Hybrid Television Services and TiVo Inc on October 31 2017. As the TiVo requires connectivity to a central server (known
More informationNFC NUTSHELL KIT. MCU Modules USER MANUAL REVISION GMMC GmbH Keywords Abstract. Document information
USER MANUAL REVISION 1.23 Document information Info Keywords Abstract Content User Manual GMMC This document describes how to use of the GMMC s NFC Nutshell KIT and its related tools GMMC GmbH www.gmmc-biz.com
More informationPage
Page 2... 3... 4... 5-6... 7-8... 9... 10... 11-12... 13... 14... 15... Index, Foreword Product Overview Preparation for Assembly Installing the Motherboard Installing the Passive CPU Cooler Installing
More informationTeensy 3.5/3.6 Breakout (Revision A, Standard)
Teensy 3.5/3.6 Breakout (Revision A, Standard) This is a breakout for the Teensy 3.5 and Teensy 3.6 development boards by PJRC. Included are all the pin headers you need to assemble it, a switch to select
More informationGospeed.Racer Hub Assembly for the Asus EEEpc
Gospeed.Racer Hub Assembly for the Asus EEEpc Before you begin: Please understand that these harnesses are all tested one at a time before I ship them. By installing this harness, you agree to assume any
More informationDiamond Cipher Drive Cartridge System (DCDC256S-C, DCDC256U-C)
Diamond Cipher Drive Cartridge System (DCDC256S-C, DCDC256U-C) www.addonics.com Technical Support If you need any assistance to get your unit functioning properly, please have your product information
More informationColorful Technology Website:
Colorful Technology Website: http://www.colorful.cn Thanks for purchasing our based on Intel B250 Chipset motherboard. The motherboard C.B250A-BTC PLUS V20 based on Intel B250 Express Chipset, support
More informationInstallation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect
Installation instructions DC Protection and Delay unit, Version 1.2 How does the unit work? Delay: Basically a capacitor is charged via a resistor, when the voltage of the capacitor reach a certain level,
More informationASUS D550MA-DS01 Motherboard
ASUS D550MA-DS01 Motherboard Replacement This guide will show you how to remove the motherboard from the laptop. Steps included in this process are removing the screws, disconnecting cables, and removing
More informationinto the EMU E4 Classic and E4 Platinum Samplers
Installing the CF-CARD SCSI Card Reader/Writer Drive into the EMU E4 Classic and E4 Platinum Samplers Thank you for purchasing the CF-CARD Internal Card Reader Drive Installation Kit from SCSICardReaders.com.
More informationHow to hardwire the Olympus D-370 and D-380 Digital Cameras
How to hardwire the Olympus D-370 and D-380 Digital Cameras Copyright, PixController http://www.pixcontroller.com, all rights reserved. This document covers in detail how to modify either the Olympus D-370
More informationPi PoE Switch HAT Quick Start And FAQ. Getting started. Kit contents
Pi PoE Switch HAT Quick Start And FAQ Getting started The Pi PoE Switch HAT is an add on board for the Raspberry Pi that brings the Switch technology together with PoE all in one fantastic package! You
More informationHuawei Ascend P6-U06 Motherboard Replacement
Huawei Ascend P6-U06 Motherboard Replacement Replace the Huawei Ascend P6-U06 motherboard. Written By: Victor Munoz ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION Replace the motherboard to
More informationWritten By: Jonathan Wear
JBL Flip 2 MicroUSB Port Replacement This guide will walk you through replacing the microusb port for this device. Written By: Jonathan Wear ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION
More informationA+ Guide to Hardware: Managing, Maintaining, and Troubleshooting, 5e. Chapter 6 Supporting Hard Drives
A+ Guide to Hardware: Managing, Maintaining, and Troubleshooting, 5e Chapter 6 Supporting Hard Drives Objectives Learn about the technologies used inside a hard drive and how data is organized on the drive
More informationBuild Your Own Home Security System
Build Your Own Home Security System Student Lab Guide Engineering Teaching Laboratory Name Date Lab Partner(s) NEW TERMS Electric Circuit: Electric circuits are paths for transmitting electric current,
More informationInstalling the upgrade memory kit in the G450 and G430 Media Gateway
Installing the upgrade memory kit in the G450 and G430 Media Gateway Important: Always check the Avaya Support Website for Product Support Notices at http://www.avaya.com/ support and select Communication
More informationInstalling TEAC CD-ROM Drives
D I G I T A L Installing TEAC CD-ROM Drives S O U N D Date: May 12, 2000 (updated) Document # TN-E211 We have used only two manufacturers of CD-ROM drives: Toshiba and TEAC. This procedure is to be used
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More information3D SYSTEMS University Cube 3D Printer
3D SYSTEMS University Cube 3D Printer Lesson Troubleshooting Machine Issues Revision date: 10/20/13 1 1 2016 年 6 月 14 日 Table of Contents Slide 3 Temperature Errors Slide 5 File Read Errors Slide 7 Filament
More informationTrueNAS Z SERIES NODE SATADOM REPLACEMENT KIT. August 2017 Edition
TrueNAS Z SERIES NODE SATADOM REPLACEMENT KIT August 2017 Edition Table of Contents Introduction... 1 Preparation... 1 Non-HA Systems Without Failover... 2 HA Systems with Failover... 2 Determine the Active
More informationJob Aid: Replacing the Field Replaceable Units (FRUs) for the Avaya G430 Media Gateway
Job Aid: Replacing the Field Replaceable Units (FRUs) for the Avaya G430 Media Gateway! Important: Important: Always check the Avaya Support Website for Product Support Notices at http:// support.avaya.com
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationThe GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.
Introduction 1 Welcome to the GENIE microcontroller system! The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationSilicon Graphics Fuel - ATX power supply adapter
Silicon Graphics Fuel - ATX power supply adapter Kuba Tyszko May 21, 2017 Disclaimer: I take no responsibility for any damages to your equipment, and will not take any warranty claims that were caused
More informationWritten By: Walter Galan
Replace a cracked screen on your iphone 4S. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this guide to replace the screen on your iphone 4S. After successfully
More informationComputer Chassis Installation Guide
Computer Chassis Installation Guide FC8 WESENA / STREACOM more infomations browse our web: www.streacom.com CONTENT FC8 overview------------------------------------------------------3 Open the Top panel-----------------------------------------------4
More informationWritten By: Brittany K
Nintendo DS Lite Motherboard Replacement Written By: Brittany K ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide has been updated by ifixit staff! Read the new, official guide here.
More informationSamsung Galaxy Tab G SIM Card Reader
Samsung Galaxy Tab 10.1 4G SIM Card Reader Replacement If you're having issues with your SIM card reader, this guide will help you replace the faulty reader with a new one. Written By: Ashley Stark ifixit
More informationAlesis MMT8 16x Memory Expansion Modification (Black model MMT8 s) Equipment. Components required. Other bits:
Alesis MMT8 16x Memory Expansion Modification (Black model MMT8 s) by Graham Meredith, 006 Revised 15 th January 009 gmeredith1@yahoo.com.au This modification expands the memory of the Alesis MMT8 to 16x
More information