Centroid ACORN CNC controller Specification and Use Guide Updated 8/3/17. Overview

Transcription

1 Centroid ACORN CNC controller Specification and Use Guide Updated 8//7 Overview ACORN is technically a CNC control breakout board for the BeagleBone Green or BeagleBone Black embedded computer the Beagle Bone. The Beagle Bone is the CNC control Motion Control CPU. When the Acorn CNC control kit is purchased directly from Centroid, the Beagle Bone is factory configured with Centroid CNC firmware and the Beagle Bone itself is preinstalled onto the Acorn Board and shipped ready to run. The remainder of this document will refer to the breakout board with the BeagleBone installed as ACORN. Features Function: Motion Control Processor, PLC, and Drive Interface Maximum number of Axes: Maximum pulse rate: 00kHz Control Interface: 00 Mb/s Ethernet to PC Drive Application: Drives with step and direction inputs Digital PLC Inputs: 8 Digital PLC Outputs: 8 Analog Output bits resolution: Dimensions (W*D*H): 5. *. * 0.7 inches svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page of 0

2 Typical Connections Connections Two connection methods are available. A female DB5 connector is available that can mate with many stepper control units with a straight through cable. The inputs and outputs are 5V compatible. Check the DB5 pinout and circuit descriptions to determine if it is compatible with a particular control unit. The DB5 provides the simplest and quickest connection method if it is compatible. Screw terminals are available for custom configurations. This allows for additional I/O and the most connection versatility. All input and output signals on the DB5 connector are available on the screw terminals except with V levels. Outputs and are open collector type on the DB5 and relay contacts at the screw terminals. Inputs may only be used on the DB5 or screw terminal, not both. For example, only screw terminal input or DB5 input may be connected at the same time. However, screw terminal input may be used at the same time as DB5 input. svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page of 0

3 DB5 (H) Signals Output Step Direction Step Direction Step Direction Step Direction Input Input Input Input Output Input 5 Output Output V COM Chassis GND Drive Interface Four sets of step, direction, and enable outputs are provided to control motor drives. The outputs are open collector type and can provide up to 00kHz step frequency. Motor Drive Connection Example ACORN Drive Outputs External Power Supply Stepper Drive COM COM EN DR Enable Direction Step H or H ST svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page of 0

4 PLC Section The ACORN has 8 digital inputs, 8 digital outputs, and one analog output. Check the ACORN I/O Map and ACORN Specifications sections to determine I/O type and capability. Outputs Two SPST relay outputs are available on board with a 0 amp rating, as well as 6 open collector outputs. Open Collector Output DB5 Connector Outputs +5 VDC Open Collector Outputs Relay Outputs Output Output Output Output Comm on Comm on Inputs ACORN uses optically isolated inputs. These inputs can be used with VDC sensors or switches. The VDC for inputs may be supplied from the ACORN logic supply. For improved isolation and noise immunity, a separate VDC may be used to power the inputs. Compare the specifications of sensors to the ACORN Specifications chart to ensure reliable operation. 5VDC Inputs DB5 Connector Inputs VDC Inputs +5 VDC.k INP UT INP UT 0 svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page of 0

5 Input Connection Examples External Power Supply Switch Wiring Example ACORN Inputs COM 5 H or H Sinking (NPN) Sensor Wiring Example ACORN Inputs External Power Supply COM Sensor COM 5 Notice: Do not use wire sensors. The voltage drop across wire sensors usually causes unreliable operation. If a wire sensor works when connected, it still may be unreliable for long term use. H or H svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page 5 of 0

6 Analog Output An analog output is provided for controlling spindle speed. The output voltage range is 0 to 0 VDC. Analog Output ANALOG - + Analog Output Analog COM Analog Output Calculations The analog output uses a bit digital to analog converter (DAC) to generate analog from the DAC request sent from the PLC program. The bit value allows a DAC request of 0 to 095, which corresponds to 0 to volts in the 0 to 0V range. Analog Output Wiring The analog output should be wired using a shielded twisted pair for best results. The analog output terminal is paired with a common terminal for direct wiring of the signal, common, and shield. In most cases, it is best to connect the shield to the common only at the ACORN. Routing analog cables away from power wires and other noise sources is also critical for good performance. See ACORN Connections section for terminal locations. svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page 6 of 0

7 ACORN I/O Map Input Specification Input Location Input Location Num Conn Pi Connec Function Type Type ber ector n tor Pin Logic w/ 5V H 5 Purpose Sourcing H6 0 Logic w/ 5V H Purpose Sourcing H6 Logic w/ 5V H Purpose Sourcing H6 H Logic w/ 5V H Purpose Purpose Purpose Purpose Purpose Sourcing Sourcing Sourcing Sourcing Sourcing H 5 H H H Logic w/ 5V H6 5 Output Specification Output Location Output Location Num Conn Pi Connec Function Type Type ber ector n tor Pin Relay, OC w/ 5V H7 Purpose SPST H6 Relay, OC w/ 5V H7 Purpose SPST H6 Open OC w/ 5V H5 H6 6 Open OC w/ 5V H5 H6 7 5 Open H5 6 Open H5 5 7 Open H5 7 8 Open H Analog out bit DAC H8 ACORN Specifications Characteristic Min. Typ. Max. Unit Volt Supply Current (Vsupply) A V Input Voltage (Vinp) - 6 VDC V Input On Voltage Vinp VDC V Input Off Voltage VDC V Input Operating current 9 5 ma Relay Output Current VAC Relay Output Current VDC svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page 7 of 0

8 Open Collector Output Current ma Open Collector Output Voltage 0 Vsupply VDC DB5 Input Voltage (internal) (VCC) VDC VCC x DB5 Input On Voltage VDC VCC x 0. VDC DB5 Input Off Voltage - - DB5 Output Voltage 0 5 VCC VDC DB5 Low Level Output Current 0 50 ma DB5 High Level Output Current 0 ma Analog Output Current 0 0 ma Analog Output Voltage 0-0 V Analog Output Resolution - - bits Size: 5. *. * 0.7 (W*D*H) Inches svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page 8 of 0

9 ACORN Connections Input 5 Input 6 Input 7 Input 8 Input VDC Step Direction Enable Step Direction Enable Step Direction Enable Step Direction Enable Output Output Input 5 Output Input VDC Input Input Input Input Input Input Input Input Direction Step Direction Step Direction Step Direction Step Output Output 8 Output 7 Output 6 Output 5 Output Output Relay NO Relay Relay NO Relay +5V +B +A +Index -B -A -Index Return N/C Encoder Input Analog Analog 0-0V Ethernet Chassis GND VDC VDC svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page 9 of 0

10 ACORN Mounting Footprint.800" (.9mm) 5.00" (7.mm).00" (06.7mm).600" (9.mm) svn:// /hardware/acorn/6050/docs/acorn_man.doc MRR Page 0 of 0

11 Acorn CNC control board Mounting Footprint Holes are clearence for 6- (.95 diameter) - 6- standoffs are recommended