Equipment Operating Procedure. Model Number: Dage-Series-4000PA Machine Name: Shear Tester Date: 8/17/2013 Serial Number:
|
|
- Teresa Conley
- 6 years ago
- Views:
Transcription
1 Equipment Operating Procedure Manufacturer: Dage Precision Location: PRC Assembly Laboratory Industries Model Number: Dage-Series-4000PA Machine Name: Shear Tester Date: 8/17/2013 Serial Number: Manufacturer Contact Information: The 4000 Project Team Dage Precision Industries Caxton Court Newcomen Way, Colchester Essex C04 4TG, England U.S.A. Tel: (510) U.S.A. Fax: (510) Machine Description/Overview: The Dage shear tester tests the strength of bonds between dies and substrates. The tool has the ability to do the following tests: Die Shear Test Heavy duty shearing. This is generally used for shearing off large chips. Ball Shear Test Precision shearing at a pre-set height above substrate. This is generally for shearing off a single ball bond. 1
2 Table of Contents Section Page 1. Setup 2 2. Operation 4 3. Shutdown 9 4. Clean up Troubleshooting 10 Procedure Results 1. Setup a. Turn on the main power by flipping the switch on the right side of the tool. The green light above the power button will turn on. The computer will begin booting. (if the computer does not boot, turn on the computer) b. Turn on the microscope light to the left of the machine. The microscope illuminator will turn on. c. The Dage series 4000 software will automatically start when the computer boots. If it doesn t, start it by double clicking on the Icon on the desktop. d. Turn on the air supply located under the desk. The valve handle should be parallel to the wall that the regulator is mounted to when turned on. (Picture There may be a hiss of air as the tool air lines fill. 2
3 below) e. Ensure that the stage is free of obstructions. Press the OK button to initialize the axes and home the stage. The stage will home and the Machine Initialization screen will close. f. Select the cartridge you wish to use. There are 3 choices: i. DS100: Die Shear for testing full dies or chips. The maximum force is 100 Kg. 3
4 ii. BS250: Ball Shear for testing individual solder balls or stud bumps. The maximum force is 250 g. iii. BS5KG: Ball Shear for testing individual solder balls or stud bumps. The maximum force is 5 Kg. g. The extra cartridges are stored on the left side of the machine. They slide out toward the front of the machine. h. To remove the currently installed cartridge, loosen the black thumb wheel above the cartridge and slide the assembly to the left. Store the cartridge on a rack on the left side of the machine. i. To install a new cartridge, slide the cartridge along the metal track from right to left. Press the cartridge to the left to seat the electrical connections. Tighten the black thumb wheel to hold the cartridge in place. 2. Operation a. Select the Test Group tab on the right side of the screen. 4
5 b. Select a test group from the drop down menu or type a new name. c. Select the Cartridge being used and set a range for the test. d. Set the following parameters for your test. Leave them as the default settings if unsure. i. Test type: 1. Destruct: the tool will increase the load until the sample fails or the maximum range is reached. 2. Non- Destruct: A known load will be applied for a given amount of time while the machine checks for sample failures. ii. Test Speed: the horizontal speed at which the sheer is performed iii. Test Load: This is the test load to be applied for a nondestructive test. This 5
6 is a set point above which tests are considered passing in destruct mode. iv. Land Speed: This is the speed at which the tool head is lowered. A low speed is recommended for fragile samples. v. Shear Height: This is the height that the tool head rebounds to after touching the board. The shear test is performed at this height. vi. Overtravel: The distance the shearing head will move after destructing the part. This can clear the part from the pad to inspect the sheared pad. vii. Fallback: leave this setting at Normal viii. Turn Vac 2 on before test: leave checked. e. Click the save button to save the parameters. f. Select the New Sample tab. Enter descriptive values in the Batch and Product fields to make finding data later easier. Do not change the operator. 6
7 g. Select the Data Output tab. Enter a path to a folder on the C: drive. Example: C:\DageTests\(your name)/(your file). h. Make sure the CSV Enable box is checked. Now select the Results tab. i. Place the sample on the stage and clamp it into place. Do not over tighten the clamp (2). The stage is stepped to allow for different size substrates. 2 j. Position the stage rotationally by sliding it around. Ensure that the sample is lined up with the tool head. Use the right joystick to lower the tool head to just above the sample to allow for alignment. 7
8 k. Align the part such that the tool is just to the rear of the part. This is shown below. This is a view from the right side of the machine. The tool head does not need to be touching the substrate. Ensure that the edge of the tool head is parallel to the edge of the chip. l. Ensure that the stage is not hanging off the table top. Once the rough alignment is complete, press the V button on the control pad to lock the stage to the table top. (shown right) m. Use the microscope to aid in alignment. The knob at the top left of the tool adjusts the microscope up and down. The knob on the upper right hand side of the tool loosens, so the microscope can be moved in and out and rotationally. 8
9 Lock it in place when satisfied. n. Adjust the sample for final alignment with the left joystick. The final alignment should look like the picture below step k. o. Ensure that you are wearing safety goggles during the test. p. Press the button at the bottom right of the screen to zero out the load cell. q. When ready to perform the test, press the Start button at the bottom right of the screen. Step back from the tool while the test is running since parts could fly across the room. The tool head will lower, then rebound to the shear height. The stage will then move to the rear of the tool as the tool head shears off the sample. r. The Results tab shows the force required to shear off the sample. It also shows a Pass or Fail designation. s. Press the sample complete button to save the file to the folder specified earlier. t. The button to the right of 3. Shutdown Print Sample will copy the data to the clip board if desired. a. Exit out of the software and 9
10 shut down the computer. b. Raise the tool head to the maximum height and remove any samples from the stage. c. Shut off the compressed air and turn off the microscope illuminator. d. Turn off the main power once the PC has shut down. The switch is on the right side of the tool. The computer and the green light above the power button will turn off. 4. Clean up a. Remove all test samples from the stage and work area. Wipe up any spills and clean up around the tool. b. Reinstall the Die Shear test fixture if it was removed. 5. Troubleshooting a. The stage slides with the shearing head instead of shearing off the chip. i. Ensure that Vac1 or 2 is on to hold the stage to the table. (check which tube is running to the black substrate holder. Might have to power cycle and reinitialize the tool if the vacuum will not turn on. b. Any other issues. i. Contact the lab manager for assistance. 10
11 Layout Microscope up and down adjustment Microscope in and out and rotational adjustment locking knob Additional Cartridge Microscope Cartridge Joystick for Z height Joystick XY direction Key Pad Keyboard 11
Prism Starter Guide 1.0 Hoskins Lab Last Modified 03/14/2017 Chris DeCiantis
Start Up: Upon entering the laser room turn on the wall mounted Laser Power Button by pulling it away from the wall. Turn on Shutter controllers (toggle switch on back of unit). There should be a U in
More informationRD-SDM02 Contact Angle Measurement Instrument. Operation Manual
RD-SDM02 Contact Angle Measurement Instrument Operation Manual The components of the RD-SDM02 system are not resistant against acids, bases or aggressive organic solvents. RD Support does not provide for
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationLECO LM247AT Microhardness Tester & Amh43 Software
Instrument Operation Instructions Department of Materials Science & Engineering Equipment: Location: Access: Contact: LECO LM247AT Microhardness Tester and Control Software 3355 Hoover Hall Open for undergraduate
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationEuphonix Max Air QUICK System Reboot Procedures CNN Los Angeles Updated:2/17/2012
**SAVE TITLE IF NEEDED** **ALL UNSAVED INFORMATION WILL BE LOST** 1) Restart the System Computer a) Hit the SYSTEM button on the right side of the Max Air Application b) Within the SYSTEM page, go to the
More informationIBM. Rack Installation Instructions
IBM Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following:
More informationPrepulse Inhibition (PPI) Boxes
Prepulse Inhibition (PPI) Boxes Always calibrate the PPI boxes prior to testing on each day See print manual for more information Calibration: 1) Turn on the boxes by switching on the surge protector on
More informationDYNAVISION D2 TM INSTALLATION MANUAL
DYNAVISION D2 TM INSTALLATION MANUAL Rev 12 Dynavision International 8800 Global Way, West Chester, Ohio 45069 USA EMAIL:info@dynavisiond2.com, WEBSITE: www.dynavisiond2.com, FAX: (905) 294-6327 Unpacking
More informationTV Brackets by equip The perfect solution to securely mount your TV
TV Brackets by equip The perfect solution to securely mount your TV No matter what s the size, if you want your TV in a fix position or want it to tilt, we have the solution you re been looking for. intro
More informationOPERATING INSTRUCTIONS:
List OPERATING INSTRUCTIONS: Preparation For Installation, Product Identification Charging The Batteries ing And Adjusting The Lift Mounting Head s Brackets Mounting Clamps And Quick-Locking Arms Installation
More informationUser Operation Manual: Motorized Valve Controller for Valved Sources
User Operation Manual: Motorized Valve Controller for Valved Sources Table of Contents BEFORE YOU BEGIN...2 Safety Precautions...2 Product Concerns...2 Specifications...3 Support...3 INTRODUCTION...4 Product
More informationVisual Physics Introductory Lab [Lab 0]
Your Introductory Lab will guide you through the steps necessary to utilize state-of-the-art technology to acquire and graph data of mechanics experiments. Throughout Visual Physics, you will be using
More informationOperating Procedure for Horiba Raman Microscope
Operating Procedure for Horiba Raman Microscope SAFETY Be aware of Laser radiation at all times! Do not remove the covers of the instrument. Components are supplied with 110V electric source. Do not touch
More informationINSTALLATION INSTRUCTIONS for the Kodak ADAPTIVE PICTURE EXCHANGE (APEX) 26, 48, 74, and 122
{InstallationInstructs}{Production}{KodakServiceSupport}{None} Publication No. II3337-2 10FEB09 INSTALLATION INSTRUCTIONS for the Kodak ADAPTIVE PICTURE EXCHANGE (APEX) 26, 48, 74, and 122 Important Qualified
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following: v Two
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationUser Manual. Binocular Zoom Stereo Microscope with Boom Stand. MicroscopeNet.com
User Manual Binocular Stereo Microscope with Boom Stand Model W42C1 Series MicroscopeNet.com Table of Contents i. Caution.. 1 ii. Care and Maintenance... 1 1. Component Illustration... 2 2. Installation...3
More informationInspiron Service Manual. 2-in-1. Computer Model: Inspiron Regulatory Model: P69G Regulatory Type: P69G001
Inspiron 13 5000 2-in-1 Service Manual Computer Model: Inspiron 13-5378 Regulatory Model: P69G Regulatory Type: P69G001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps
More informationGV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000
GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000 Instruction Manual D2-3390-2 The information in this manual is subject to change without notice. Throughout this manual, the
More informationV40 Videoboom MAIN OPERATING INSTRUCTIONS INDEX 5. SPECIFICATIONS V40 1. INTRODUCTION 2. LIST OF FUNCTIONS AND PARTS
MAIN OPERATING INSTRUCTIONS V40 Videoboom INDEX 1. INTRODUCTION 2. LIST OF FUNCTIONS AND PARTS 3. INSTRUCTIONS V40 3.1 ASSEMBLY & SETTING UP 3.2 WEIGHT SYSTEM 3.3 MOUNTING THE VIDEO CAMERA 4. USING THE
More informationskyline 70 Fluid Head OPERATOR S MANUAL #1050 Skyline 70 Fluid Head
skyline 70 Fluid Head OPERATOR S MANUAL #1050 Skyline 70 Fluid Head Features and Controls Sliding Plate Lock Sliding Plate Pan Handle Clamp Tilt Lock Pan Handle Safety Lock Knob Pan Lock Threaded Stud
More informationTitan Media Cart. Installation and Operation Manual
Titan Media Cart Installation and Operation Manual Table of Contents INTRODUCTION SERVICE AND SUPPORT... 1 PRODUCT RETURNS... 1 UNPACKING... 1 TITAN SINGLE MEDIA CART... 2 TITAN DUAL MEDIA CART... 2 BEFORE
More information24KO VARIO INSTRUCTION FOR MOBILE PROJECTION SCREENS VARIO 32 AND VARIO 64
24KO VARIO INSTRUCTION FOR MOBILE PROJECTION SCREENS VARIO 32 AND VARIO 64 CENTRE SUPPORT Consists of plug in elements with interlocking and safety bolts. Adaptable to any frame size FOLDABLE LEGS Standard
More informationINTEGRATION SOLUTIONS
INTEGRATION SOLUTIONS .TOTAL Flexibility.TOTAL Control The very foundation of inc.jet s printing solutions is thermal inkjet technology (TIJ). inc.jet offers ready-to-run, high-resolution, variable data
More informationDell Edge Gateway. Service Manual Series
Dell Edge Gateway 5000 Series Service Manual Computer Model: Dell Edge Gateway 5000/5100 Regulatory Model: N01G/N02G Regulatory Type: N01G001/N02G001 Notes, cautions, and warnings NOTE: A NOTE indicates
More information6 x 6 Peltier-Thermostatted Multicell Holder Series II Accessory
6 x 6 Peltier-Thermostatted Multicell Holder Series II Accessory Overvoltage Category II Pollution Degree 2 Equipment Class III Safety information Introduction Before using this accessory, you must read
More informationSKI TYPE A SKI TYPE B SKI TYPE A
INTEGRATION SOLUTIONS 15 User Interface (5019311G) The User Interface (UI) is a Windows XP Embedded, 15" touch screen computer which provides print job design, printer configuration, control and monitoring
More information5mW Class 3R Laser Alignment
Name of SOP 5mW Class 3R Laser Alignment Effective Date 4 June 2009 Author Mark Mihaljevic Reason for SOP Check All that Apply: Safety of the operator, people around and equipment Procedure/Process could
More informationReplacing the SATA PCI Controller Card
Replacing the internal controller PCI card may be performed by a single administrator; no tools are necessary. Caution There are static-sensitive electronics inside the unit. Before you handle any parts,
More informationZeiss AxioImager.Z2 Fluorescence Protocol
Zeiss AxioImager.Z2 Fluorescence Protocol 1) System Startup Please note put sign-up policy. You must inform the facility at least 24 hours beforehand if you can t come; otherwise, you will receive a charge
More informationFurther Information can be found at
Below is a step by step guide to assembling the Hurricane-Rig. Remember that this is a precision optical instrument. Excessive force can bend critical parts. If treated well it should give many years of
More informationDell Inspiron N5110 Service Manual
Dell Inspiron N5110 Service Manual Regulatory model: P17F Regulatory type: P17F001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationMAKE SURE TO TURN OFF YOUR TRS-80 BEFORE ATTACHING NEWKEY/80 KEYBOARD RIBBON CABLE AND POWER CABLE.
NEWKEY/80 User's Guide v1.4 TRS80 Keyboard Adapter 12/10/2018 Plaid Vest Software, LLC. www.plaidvest.com/newkey80 IMPORTANT NOTE: MAKE SURE TO TURN OFF YOUR TRS-80 BEFORE ATTACHING NEWKEY/80 KEYBOARD
More informationPerkinElmer Series 200 HPLC: Operating Procedure
PerkinElmer Series 200 HPLC: Operating Procedure Chem Eng 5503 Version 1.01 Last Update 8/9/07 This document outlines the basic operating procedure for the PE series 200 HPLC, UV/Vis and SEDEX Light Scattering
More informationInspiron 22. Service Manual Series. Regulatory Model: W17B Regulatory Type: W17B001
Inspiron 22 3000 Series Service Manual Regulatory Model: W17B Regulatory Type: W17B001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationCRESCENDO /7200 G3. Quick Start Guide for Crescendo /7200. Processor Upgrade Card for Power Macintosh 7200/8200 Computers
CRESCENDO /7200 G3 Processor Upgrade Card for Power Macintosh 7200/8200 Computers Quick Start Guide for Crescendo /7200 System Compatibility At this printing, processor upgrade cards are compatible with
More informationWritten By: Walter Galan
imac Intel 21.5" EMC 2428 CPU Replacement Replace the CPU in your imac Intel 21.5" EMC 2428. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION Use this guide to upgrade
More informationapple Service Source Apple Cinema Display 22" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema Display 22" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema Display 22" LCD (ADC) 2003 Apple Computer,
More information194B Dual LCD Arm Specifications
194B Dual LCD Arm Weight capacity: 6 kgs each screen up to 22 Meets with VESA 75*75 and 100*100mm. The two arms are easily adjustable for swinging into any position With C-Clamp for desktop mounting. 193B
More informationUser Manual. Trinocular Stereo Microscope
User Manual Trinocular Stereo Microscope Model V434 XV434 Series MicroscopeNet.com Table of Contents i. Caution.. 1 ii. Care and Maintenance... 2 1. Component Illustration... 3 2. Installation 4 3. Operation....6
More informationService Manual - Memory Upgrade
Inspiron 14 3000 Series Service Manual - Memory Upgrade Regulatory Model: P53G Regulatory Type: P53G002 Contents Before working inside your computer...3 Before you begin... 3 Safety instructions... 3 Recommended
More informationHaze 800 DMX. User Guide. English
Haze 800 DMX User Guide English Introduction Box Contents Haze 800 DMX Remote Control (wired) User Guide Safety & Warranty Manual Support For the latest information about this product (documentation, technical
More informationEVOLVE1-M MONITOR ARM
EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before
More informationUser Manual. Trinocular Stereo Microscope
User Manual Trinocular Stereo Microscope Model V436 XV436 Series MicroscopeNet.com Table of Contents i. Caution.. 1 ii. Care and Maintenance... 1 1. Component Illustration... 2 2. Installation 3 3. Operation....4
More informationBiology 105 Laboratory 1: Microscope
Biology 105 Laboratory 1: Microscope A. The Compound Microscope The microscope is a delicate, precision instrument. It must be treated gently, as the slightest bump or jar may damage the alignment of its
More informationCRESCENDO /PB G3. Processor Upgrade Card for Macintosh PowerBook 1400 Series Computers. Quick Start Guide for Crescendo/PB G3
CRESCENDO /PB G3 Processor Upgrade Card for Macintosh PowerBook 1400 Series Computers G3 Macintosh PowerBook and Operating System Compatibility The Crescendo/PB G3 processor upgrade card is compatible
More informationAdjust-O Magnet Squares
Adjust-O Magnet Squares The original magnet squares featuring On/Off switches. Patent No. US 7,009,480 B2 Adjust-O Magnet Squares The On/Off switch HEAVY DUTY HEAVY DUTY MSA45 MSA48-HD MSA53-HD Multiple
More informationkena TM Instruction Manual T-1050
kena TM Instruction Manual T-1050 2 Table of Contents Introduction / Package Contents 4 Diagram 4 Package Contents 5 Operational Requirements 5 Optional Accessories to Order 5 Specifications 6 Quick Start
More informationDUAL-ARM MONITOR MOUNT For in. ( cm) desktop computer monitors
LeviTouch DM-502 DUAL-ARM MONITOR MOUNT For 15 27 in. (38.1 68.6 cm) desktop computer monitors User Manual Thank you for choosing Gabor. The Gabor Dual-Arm Desktop Mount can securely support two monitors
More informationCondensed AFM operating instructions:
Condensed AFM operating instructions: 1. Log onto system at access controller 2. Take the parts you need to mount a probe out of the drawers. You need the appropriate probe holder, tweezers (these are
More informationkena Instruction Manual T-1050
kena Instruction Manual T-1050 2 Table of Contents Introduction / Diagram 4 Package Contents 5 Operational Requirements 5 Optional Accessories to Order 5 Specifications 6 Quick Start Guide 7 1. Install
More informationSAVE THESE INSTRUCTIONS
and Height Mounts Assembly, Installation and Operating Instructions Model Nos. QL, QLA, ARM250, QLM6 and QLAM6 NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact
More informationThank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com.
Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Please check out our ebay auctions for more great deals on Factory Service Manuals: servicemanuals4u Dell Latitude
More informationUnpacking and Installing the Flora 2512 UV Printer. Steps 1: Unscrew the 10mm bolts holding the top. Then remove the top and put in a safe place.
Unpacking and Installing the Flora 2512 UV Printer Steps 1: Unscrew the 10mm bolts holding the top. Then remove the top and put in a safe place. Step 2: Unscrew 10mm bolts holding the end panels. On the
More informationPH 481/581 Physical Optics Winter 2018
PH 481/581 Physical Optics Winter 2018 Laboratory #1 Week of January 15 Read: Section 5.2 (pp.151-175) of "Optics" by Hecht Do: 1. Experiment I.1: Thin Lenses 2. Experiment I.2: Alignment Project 3. Experiment
More informationOperation Manual. 4Bank DMX
Operation Manual 4Bank DMX Part No. 3100070 Rev C 08-29-2017 Systems CFX-484 4ft 4Bank Fixture w/ Louver/HP, 90 CFX-244 2ft 4Bank Fixture w/ Louver/HP, 90 MTP-KW41 Kino 41K Mount Wing w/ 3/8 Pin (10mm)
More informationONYX 32 MULTIFUNCTIONAL POSITIONING AND SOLDERING SYSTEM
ONYX MULTIFUNCTIONAL POSITIONING AND SOLDERING SYSTEM MACHINES.0 APPLICATION: SMT ZEVAC-LINE: ONYX The complete ONYX product line documentation is composed of the following data sheets: MACHINES.0 ACCESSORIES.0,.0
More informationBFW Traveler: Assembly and Alignment Procedure Serial Number: BFW # / VC # / WC # / Base #
BFW Traveler: Assembly and Alignment Procedure Serial Number: BFW # / VC # / WC # / Base # NOTE - This document: 1. records the assembly and alignment steps for the LCLS Undulator Beam Finder Wire (BFW).
More informationABM's High Resolution Mask Aligner Features:
ABM's High Resolution Mask Aligner is a very versatile instrument with interchangeable light sources which allow Near-UV (405-365 nm) as well as Mid- and Deep-UV (254 nm, 220 nm) exposures in proximity
More informationM40 Microscope User s Manual
M40 Microscope User s Manual for M40 and M40RT Microscope Components: Trinocular Port Eyepieces Beam Splitter Field Diaphragm Adjustment Aperture Diaphragm Adjustment Filter Slots Analyzer Polarizer Hex
More informationC-pan arm USERS INSTRUCTIONS
C-pan arm USERS INSTRUCTIONS Designed 1 of 12 and made in Denmark Thanks for purchasing a 9.Solutions product. With great passion, we design our products to be as versatile as possible. We hope that our
More information1551 S. Harris Court,. Anaheim, CA Phone: Fax:
1551 S. Harris Court,. Anaheim, CA 92806 Phone: 714.978.1551... Fax: 714.978.0431 Model 4KE / 4KEH Series: Semi-Automatic, Motorized Y/Z Axes, Wedge-Wedge, Ball- Wedge Triple-Convertible Wire Bonders Last
More informationTable of Contents. 1 Welcome. 2 Install your Access Point-I. 3 Using the Access Point-I
Table of Contents 1 Welcome Introducing the Avaya Wireless LAN 1-1 About the Access Point-I 1-2 Finding Information 1-3 2 Install your Access Point-I Overview 2-1 Verify Kit Contents 2-2 Write Down Product
More informationminipcr Mobile App operation (Android devices) Appendix: maintenance and operating conditions
minipcr TM Thermal Cycler User s Guide Contents I. Loading your samples II. Setting up your minipcr TM thermal cycler III. Creating, storing, and editing protocols IV. Running and monitoring protocols
More informationPL200. Automatic Slide loader Manual Version 3.3
PL200 Automatic Slide loader Manual Version 3.3 Prior Scientific, Ltd Prior Scientific, Inc Prior Scientific, GmbH Prior Scientific, KK Cambridge, UK Rockland, MA. USA Jena, Germany Tokyo, Japan T. +44
More informationDS5/DS10/DS20 Fluid Head Operator s Manual. #180 DS5 Fluid Head #182 DS10 Fluid Head #184 DS20 Fluid Head
DS5/DS10/DS20 Fluid Head Operator s Manual #180 DS5 Fluid Head #182 DS10 Fluid Head #184 DS20 Fluid Head Features and Controls 1/4 and pin carriage Sliding camera plate Slide lock Tilt lock Tilt drag Pan
More informationAllworx 24x Service and Troubleshooting Guide
Allworx 24x Service and Troubleshooting Guide -PAGE INTENTIALLY LEFT BLANK- Table of Contents 1 Safety Instructions...1 1.1 Electrical...1 1.2 Electrostatic Discharge...1 2 Chassis Views...2 3 Exterior
More informationPrecautions The XRD uses x-ray radiation. The instrument is designed to prevent radiation exposure.
1 Operating Procedure for X-Ray Diffraction Purpose and Scope This document describes the procedures and policies for using the MSE Bruker D8 Focus XRD The scope of this document is to establish user procedures.
More informationworkstation acessories ErgoChair ergonomic chair designed for the factory worker
workstation acessories ErgoChair ergonomic chair ErgoChair ergonomic chair designed for the factory worker the backrest and seat foot ring adjustment ranges are designed to cover a large variety of production
More informationAPES-14 HD-6500 & HD-7000 Version Operator s Training Manual
APES-14 HD-6500 & HD-7000 Version Operator s Training Manual Issue A1 09/03 PDI Part # 900600 Performance Design Inc. 2350 East Braniff St. Boise Idaho 83716 This manual contains very important safety
More informationComputer Assembly Step by Step DRAFT
9781587132636_ch03.qxp 8/20/10 1:37 PM Page 79 CHAPTER 3 Computer Assembly Step by Step Objectives Upon completion of this chapter, you should be able to answer the following questions: How do I open the
More informationUser Manual. Revision B
User Manual TM Revision B Copyright 2014 Electronic Theatre Controls, Inc. All Rights reserved. Product information and specifications subject to change. Part Number: 7063M1220 Rev B Released: 2014-07
More informationInstallation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationD-SCOPE The indispensable analysis tool for all diamonds
www.hrdantwerp.be D-SCOPE The indispensable analysis tool for all diamonds The indispensable analysis tool for all diamonds HRD Antwerp has a long experience in research, examination and grading of diamonds.
More informationIEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine
IEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine The image below is our ARIX Milling machine. The machine is controlled by the controller. The control panel has several
More informationMobile Office System
Mobile Office System Sit Stand Car Desk User Guide The Sit Stand Car Desk turns the rear seat of virtually any four door vehicle into a comfortable working environment. The system is designed to safely
More informationHARMONi G3. Quick Start Guide for HARMONi G3. imac Processor/FireWire Upgrade
HARMONi G3 imac Processor/FireWire Upgrade imac and Operating System Compatibility The HARMONi G3 imac processor/firewire upgrade is compatible only with imac 233, 266, and 333 MHz models (Revisions A-D);
More informationDL1000 DURABILITY & LUBRICITY TEST SYSTEM
OakRiver Technology s DL1000 provides accurate, reliable measurement of the durability and lubricity of hydrophilic coatings on catheters and guidewires. Engineered with robust components and controls,
More informationAdding or Replacing a PCI Card
Caution There are static-sensitive electronics inside the unit. Before you handle any parts, make sure you are working at a static-controlled workstation and that you are properly grounded. Three PCI cards
More informationGardner-scrub Abrasion Tester
Measure what you see. Gardner-scrub Abrasion Tester Manual A member of Additives & Instruments Gardner-scrub Abrasion Tester Instruction Manual English 298 023 140 E 1507 BYK - Gardner USA 9104 Guilford
More informationPREFACE. Thank you for choosing Zen Space Desks. We hope your desk helps you find your zen when being used. Zen Space Desks Team
INSTRUCTION MANUAL PREFACE We are thrilled that you have chosen Zen Space. Congratulations, you have selected one of the most advanced and sophisticated Power Adjustable Workstations available today. Our
More informationReplacing/Upgrading Mac Pro Processors (Early 2008)
Replacing/Upgrading Mac Pro Processors (Early 2008) The steps in this procedure illustrate how to remove the lower processor (CPU B). The instructions are the same for removing the upper processor (CPU
More informationTriboIndenter Manual
Boston University Laboratory for Biomedical Materials Research TriboIndenter Manual Version 2.1 Date: April 2006 Authors: Ayyana Chakravartula, Dezba Coughlin, Donna Ebenstein & Cheng Li, Catherine Klapperich,
More informationProduct Overview. Features
APCF1 Model Tripod Product Overview The Ravelli APCF1 is a Professional Quality Carbon Fiber Tripod providing a solid base for high-end photographic equipment. This model is a mix of carbon fiber and magnesium
More informationFlexCam icam. Digital User Manual PAL
FlexCam icam Digital User Manual 910-171-102 910-171-102-PAL 5615 Raytown Road Kansas City, MO 64133 U.S.A. Tel.: 816-353-4787 Fax: 816-358-5072 email: flexcam@ken-a-vision.com www.ken-a-vision.com 800-171-102
More informationEBL (Elionix EBeam Lithography System) CAD Procedure
EBL (Elionix EBeam Lithography System) CAD Procedure Authors: Nigel Carroll & Akshara Verma Date: 12 April 2016 Version: 1.0 To create a pattern within a single field 1. Open CAD software 2. Click on Settting
More informationTitanUNIVERSAL STRENGTH TESTER
TitanUNIVERSAL STRENGTH TESTER Titan INNOVATION GUARANTEED The new Titan Universal Strength Tester comes from a family of innovative equipment, designed and manufactured by James H. Heal the World s Premier
More informationApplications : LA-51-1 LA-52-1 LA-51-2 LA Features : LA-51-3 LA-52-3 LCD SUPPORTER KEYBOARD ARM
Applications : It goes well with partition boards and tracks in an office, or Medicine table at a dentist, or Medical equipment at a clinic or mobile cart, or Industrial machinery or monitor system at
More informationSystem Storage EXP3000 Rack Installation Instructions
System Storage EXP3000 Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When you install the IBM System Storage EXP3000 in a
More informationFlip-Chip-Aligner-Bonder Model M-8HP
Flip-Chip-Aligner-Bonder Model M-8HP 1. Introduction DO NOT CHANGE THE SETTINGS OF THE VIDEO CAMERAS UNLESS YOU ARE AUTHORIZED TO CALIBRATE THE MACHINE AND KNOW WHAT YOU ARE DOING! The laminar flow hood
More informationXPS 15 2-in-1. Service Manual. Computer Model: XPS Regulatory Model: P73F Regulatory Type: P73F001
XPS 15 2-in-1 Service Manual Computer Model: XPS 15-9575 Regulatory Model: P73F Regulatory Type: P73F001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better
More informationWritten By: senordingdong
Installation of the UniMac V4 adapter into the Apple imac Intel 17". This enables the usage of non OEM LCD panels, and offers an otherwise unavailable Full HD upgrade. This used for repair of the common
More informationInterior Exploded View of Wavelength Series "A" in a Kiosk/Panel-Mounted
Interior Exploded View of Wavelength Series "A" in a Kiosk/Panel-Mounted Kiosk Interior VHB Adhesive Wavelength Touch Frame VHB Adhesive Tempered Glass (Glossy or A.R.) USB Controller Cable The touch screen
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. Before installing your server in a rack cabinet, review the following guidelines:
More informationOPERATING MANUAL. Gilson Rice Shaker SGA-5R & SGA-5RT
OPERATING MANUAL Gilson Rice Shaker SGA-5R & SGA-5RT Rev: 05/08/2018 PHONE: 800-444-1508 P.O. Box 200, Lewis Center, Ohio 43035-0200 FAX: 800-255-5314 740-548-7298 E-mail: customerservice@gilsonco.com
More informationFRDM Replacement Procedure
Operating Documentation Direction 5193574-800, Rev# 21 LightSpeed 7.X Service Methods Module Version 11.0, Version Date 3/20/14 FRDM Replacement Procedure (Click Here for Summary Version) 1 Overview This
More informationAlienware Area-51 R5 Service Manual
Alienware Area-51 R5 Service Manual Computer Model: Alienware Area-51 R5 Regulatory Model: D03X Regulatory Type: D03X002 Notes, cautions, and warnings NOTE: A NOTE indicates important information that
More information