3M DSLAM Mounting Bracket Kit J0746
|
|
|
- Margaret Richard
- 6 years ago
- Views:
Transcription
1 3M DSLAM Mounting Bracket Kit J0746 Instructions July
2 Contents 1.0 3M DSLAM Mounting Bracket J Installation DSLAM Installation, Nokia Accessory Kit, Cable Addition Shroud J0747 for DSLAM Mounting Kit Cable Routing...7 2
3 1.0 3M DSLAM Mounting Bracket J Installation 1.1 Unpack DSLAM Mounting Bracket. Note: Nokia configuration shown. 1.2 DSLAM cables can be routed through the base of the cabinet below the isolation plate and/or above it through the blanking plate holes. 1.3 Cable Routing Below Isolation Plate: Using a Green-lee punch, punch two, 2" holes in center of the base as shown below. Punch two, 2" holes 11.5" above grade. 1.4 Cable Routing Above Isolation Plate: Punch two, 2" holes 11.5 and 14" from baseline as shown. 1.5 Lower DSLAM Mounting Bracket Mounting Bolts: Drill four, 7/16" holes 19-5/8" and 21-3/8" above baseline as shown. 3
4 1.6 Remove cap bolts, lifting bracket bolt and carriage bolts plugging top mounting holes for 3M DSLAM Mounting Bracket. 1.7 Mount DSLAM mounting bracket on the side panel of the expanded cabinet. 1.8 Secure base with four self drilling screws through the two base cable ports and into 3M Cross- Connect Cabinet 4220G upright. two screws per side. 1.9 Install the top two and bottom four retaining bolts to secure the DSLAM mounting bracket to the cabinet side panel with ¼ bolt(s), lock washer(s) and flat washer(s). 4
5 2.0 3M DSLAM Mounting Bracket Installation, Nokia 2.1 Remove adapter ring and cover plate. 2.2 Remove side and lower access panels. 2.3 Remove RDAC lifting brackets. 2.4 Clean the side of the RDAC to be mated to the expanded cabinet. Remove liner from 2.5 x black rubber gasket. Align 3/8 holes in gasket with the two holes in the RDAC. Apply gasket. This gasket will prevent any water running down the walls between the RDAC and DSLAM mounting bracket. 2.5 Lift DSLAM onto mounting base. Using pallet anchor bolts secure DSLAM base. 2.6 Install upper mounting bolts. 2.7 Run a bead of RTV sealant along seams between cabinet and DSLAM mounting bracket and between RDAC and DSLAM mounting bracket. 5
6 3.0 Accessory Kit, 3M Cable Addition Shroud J0747 for 3M DSLAM Mounting Bracket Kit In situations where there isn t a free cable duct for fiber feed cable it will be necessary to install a cable addition shroud. 3.1 Remove lower and side access panels. 3.2 Place base panel and floating duct panel over cable duct. 3.3 Center floating panel around duct, secure in place with self-drilling/tapping screws. 3.4 Slide duct housing into place as shown. 3.5 Re-install side access panels with ¼ hardware. 6
7 4.0 Cable Routing Note: Pictures are of a 3M Cross-Connect Cabinet 4200G2K-DSL expansion 4.1 Below Isolation Plate. 4.2 Above Isolation Plate. 7
8 3M is a trademark of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Communication Markets Division 3M Telecommunications 6801 River Place Blvd. Austin, TX Please Recycle. Printed in USA. 3M All Rights Reserved.
3M Cross-Connect Cabinet Riser Installation Guide
3M Cross-Connect Cabinet Riser Installation Guide Installing riser in stake, hand hole and pad-mount applications Instructions October 2016 78-0015-3063-9-B 2 October 2016 78-0015-3063-9-B Contents 1.
3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs)
3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs) Instructions August 2011 3 78-8130-2330-1-C 1.0 General 1.1 The 3M Add-On Terminals 4220P-100, 4220P-200, 4220P-300 and 4220P-400 are designed to expand
Mounting Bracket for 8 in. Charles Industries Pedestal for use with 3M Fiber Dome Terminal Closure FDT 08
Mounting Bracket for 8 in. Charles Industries Pedestal for use with 3M Fiber Dome Terminal Closure FDT 08 Instructions October 2006 78-8135-6184-8-A 1.0 Introduction This kit mounts a 3M Fiber Dome Terminal
3M I/O Connector Mounting Options and Hardware
M I/O Connector Mounting Options and Hardware Hardware Guide Date Modified: July 20, 2009 Part Number Type Mounting Hardware Applications - Table 1 Mini D Ribbon (MDR) Conn. s D Sub Conn. s D Ribbon Conn.
3M Serial Advanced Technology Attachment (SATA) Connector Signal Plug, Boardmount, Surface Mount Right Angle and PTH Vertical
7-position supports motherboard signal requirements EMLB contacts for hot swap Blind mate polarization for easy cable attach Through-hole and surface mount options PCB retention clip aids manufacturing
Indoor Protected Entrance Terminal 4588 Series
Indoor Protected Entrance Terminal 4588 Series Instructions Underwriters Laboratories (UL) Listed September 2003 78-8135-1209-8-A 1.0 General The 3M Indoor Protected Entrance Terminal (PET) 4588 Series
3M Compact Coarse Wave Division Multiplexer (CCWDM) Module Installation
3M Compact Coarse Wave Division Multiplexer (CCWDM) Module Installation Instructions June 2010 3 Contents 1.0 Introduction...3 2.0 Kit Contents...3 3.0 Preparation and Installation of One and Two 3M Compact
3M SLiC Fiber Splicing Workstation with Cleaver Arm
3M SLiC Fiber Splicing Workstation with Cleaver Arm Terminal Closure 530 Closures 533, 547 and 733 Instructions September 2016 78-8135-7148-2-D 2 September 2016 78-8135-7148-2-D 1.0 General 1.1 The 3M
3M Indoor Protected Building Entrance Terminal 4588V-QCS Series
3M Indoor Protected Building Entrance Terminal 4588V-QCS Series with 3M Quick Connect System 2811 Dry Flame Retardant Block Instructions Underwriters Laboratories (UL 348X) Listed April 2010 3 78-0013-1813-4-A
3M Passive Optical Splitter Shelves and Modules
Communication Markets Division 3M Passive Optical Splitter Shelves and Modules 3M offers a robust portfolio of passive optical fiber splitter products made to enable easy configuration, design, ordering,
3M Fiber Dome Closure FDC 08S-A. 3M Fiber Dome Closure FDC 08S-B. Constructed of highly chemicalresistant
The new, compact 3M Fiber Dome Closure FDC 08S is a hermetically sealed fiber dome closure for aerial, buried above-grade, and buried below-grade applications. This closure is designed to meet the needs
3M Pak 100 Wiremount Plug Series
Pak 100 Wiremount Plug Shrouded to protect against physical and chemical pin damage Open or closed end covers available Optional ejector latches Accepts flat cable or discrete wire Military (with 3518
3M Indoor Building Entrance Terminal (IBET) 4790V and 4790VL Series
3M Indoor Building Entrance Terminal (IBET) 4790V and 4790VL Series with 3M Quick Connect System (QCS) 2811 Dry Flame-Retardant Block and RJ-11 Test Ports Instructions Underwriters Laboratories (UL 348X)
3M Indoor Protected Building Entrance Terminal (IBET) 4688V Series
3M Indoor Protected Building Entrance Terminal (IBET) 4688V Series Instructions Underwriters Laboratories (UL 348X) Listed February 2017 78-0013-6127-4-B 2 February 2017 78-0013-6127-4-B 1.0 General The
3M I/O Connector Mounting Options and Hardware
M I/O Connector Mounting Options and Hardware Hardware Guide Date Modified: January 14, 2008 Part Number Type Mounting Hardware Applications - Table 1 Mini D Ribbon (MDR) Conn. s D Sub Conn. s D Ribbon
3M Duplex Polishing Machine 6851-E with Universal Dual Holder Instructions
3M Duplex Polishing Machine 6851-E with Universal Dual Holder Instructions Safety Information Read, understand and follow all safety information contained in these user instructions prior to use of the
3M Indoor Protected Building Entrance Terminal 4788V-QCS Series
The Network of Networks. 3M Indoor Protected Building Entrance Terminal 4788V-QCS Series with 3M Quick Connect System (QCS) 2811 Dry Flame Retardant Block for Field-Terminated Building Cables Instructions
3M Mini-Clamp Socket 2 mm Boardmount, Straight Solder Tails 372 Series
2 mm Boardmount, Straight Solder Tails 72 Series Compact design saves board space High number of mating cycles Mating latch features provide a reliable interconnection in demanding applications Enables
3M 4-Wall, Tripolarized Header.050".100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle 810 Series
Tripolarized for robust alignment when mating to 820 series socket 50 mil 100 mil halves the connector length vs. traditional 100 mil x 100 mil products Latching Ejector for rugged high performance applications
3M Boardmount Socket 2 mm x 2 mm Straight Surface Mount, Straight and Right Angle Plated Through-Hole 1502 Series
M Boardmount Socket High Temperature Insulator Reflow Solder ompatible Low height helps minimize PB stack height End Stackable Thru-hole versions are side stackable SMT parts are available in tape and
Model 1100B CHG Terminator. Operating Instructions
Model 1100B CHG Terminator Operating Instructions 1 Contents: 1.0 Safety Information... 3 2.0 General Introduction... 3 3.0 Operation... 4 2.8 2.1 2.7 V 2.2 2.9 2.2 2.10 2.11 2.11 2.3 2.4 2.5 2.5 2.6 2
3M Cross-Connect Cabinets for Midspan Applications
Communication Markets Division 3M Cross-Connect Cabinets for Midspan Applications 3M Cross-Connect Cabinets for midspan applications are low-count cabinets available in configurations that can accommodate
3 Angled Connector Housing (MC) Installation
Angled Connector Housing (MC) Installation Instructions July 1999 4-7047-2554-7 MC Frame Figure 1 Angled Connector Housing (MC) General This document describes the installation of the stubbed MC Angled
3M Connectors for Embedded Systems Connectors for AdvancedTCA, CompactPCI and MicroTCA Systems from 3M
3M Connectors for Embedded Systems Connectors for AdvancedTCA, CompactPCI and MicroTCA Systems from 3M 3M 2011. All Rights Reserved. Introduction Purpose To explain the features and benefits of the connectors
3M Quick Connect System (QCS) 2814
Communication Markets Division 3M Quick Connect System (QCS) 2814 Designed for your broadband network The 3M Quick Connect System 2814 is a terminal/cross-connect system featuring integrated protection
3M Quick Connect System (QCS) 2811
Communication Markets Division 3M Quick Connect System (QCS) 2811 Designed for your broadband network The 3M Quick Connect System (QCS) 2811 is an insulation displacement connector (IDC) termination system
3M Textool BGA Test & Burn-In Sockets 1.00 mm, Types 0, I, II and III Open Top
Textool BGA Test & Burn-In Sockets 1.00 mm, Types 0, I, II and III Open Top Double-beam normally-closed contact delivers balanced, opposing forces to solder ball with minimal shear stress Contact tips
3M SLiC Fiber Aerial Terminal Closure 530 Internal for Direct Spliced Drop Terminations. 3M External Cable Assembly Module (ECAM) 12mm Drop Entry Kit
3M SLiC Fiber Aerial Terminal Closure 530 Internal Drop Terminations for Direct Spliced Drops The 3M SLiC Fiber Aerial Terminal Closure 530 with Internal Drop Termination is an aerial, strand-mount, free-breathing
Product Discontinuation Notice 3M Assorted Japan Sourced Connectors
Product Discontinuation Notice 3M Assorted Japan Sourced Connectors Issue Number: 756 Date: March 26, 2010 Product Discontinuance Effective June 1, 2010, 3M will exit a few assorted low volume Japanese
Dynatel Advanced Modular System 965AMS ADSL2+ Service Module
3 Dynatel Advanced Modular System 965AMS ADSL2+ Service Module User s Guide Future-Proof Testing Platform May 2006 78-8135-5269-8 Contents ADSL2+ Service Module...5 Module Installation...5 Hook-Up...6
3M Fiber Dome Terminal Closures FDTC 08M and FDTC 08S External Drop Termination
3M Fiber Dome Terminal Closures FDTC 08M and FDTC 08S External Drop Termination The compact 3M Fiber Dome Terminal Closures FDTC 08M and FDTC 08S are hermetically sealed fiber dome terminal closures for
Dynatel.Advanced.Modular.System. 965AMS.VDSL2.Service.Module.
3 Dynatel.Advanced.Modular.System. 965AMS.VDSL2.Service.Module. User s.guide Future-Proof Testing Platform October 2007 78-8135-7673-9 Contents VDSL2 Service Module...5 Introduction...5 Module Installation...6
3M Sensored Cable Accessories for Underground Medium Voltage Distribution System
3M Sensored Cable Accessories for Underground Medium Voltage Distribution System 3M Electronics & Energy Business 1 Introduction The focus on enhancing reliability and efficiency of the power grid has
3M Constant Monitors WSMONITOR1, WSMONITOR 2, WSMONITOR3
3M Constant Monitors WSMONITOR1, WSMONITOR 2, WSMONITOR3 User s Guide WSMONITOR1 WSMONITOR2 WSMONITOR3 Table of Contents Section Page SAFETY INFORMATION...3 Introduction...5 Installation...6 Operation...9
A significantly increased capacity compared to other techniques is achieved with the compact SID-C module.
3 Quante SID System With the SID-C product family, 3M is setting the standard for high-density IDC termination combined with improved handling. The main applications are in telecommunications and data
Volition. VF-45 Singlemode Socket and Patch Cords. 3Innovation IT'S AS EASY AS PLUGGING IN AN RJ-45.
Volition VF-45 Singlemode Socket and Patch Cords IT'S AS EASY AS PLUGGING IN AN RJ-45. The Volition VF-45 Singlemode Socket and Patch Cords from 3M are the latest duplex, fiber optic interconnect products
3M Textool Open-Top Test and Burn-In Sockets for Ball Grid Array Packages
3M Textool Open-Top Test and Burn-In Sockets for Ball Grid Array Packages 3Innovation Table of Contents Product Advantages...1 Durability...1 Reliability...2 Micro-Wiping and Solder Ball Deformation...3
For more information, visit: 3M Cold Shrink QS-III Splice a one-piece joint with wide range and geometric stress control
for Medium Voltage Grid Automation Visibility inreal Time An effective solution for monitoring your underground distribution system 3M is a global technology company, manufacturing over 50,000 products
Volition. Multimode VF-45 Socket and Patch Cords. 3Innovation
Volition Multimode VF-45 Socket and Patch Cords It's as easy as plugging in a rj-45. The Volition VF-45 Socket and Patch Cords from 3M are the latest duplex, fiber optic interconnects for affordable, high
3M Fiber Distribution Units 8400 Series
Communication Markets Division 3M Fiber Distribution Units 400 Series Flexible options to meet growing needs in limited spaces 3M offers a full line of patch panel designs to simplify your cable management
Volition. Multimode VF-45 Socket and Patch Cords. 3Innovation
Volition Multimode VF-45 Socket and Patch Cords O b D s oc ol e um te en t It's as easy as plugging in a rj-45. The Volition VF-45 Socket and Patch Cords from 3M are the latest duplex, fiber optic interconnects
A Full Range for Different Applications The STG2000 modules offer three different types of IDC circuits. The Network of Networks
The Network of Networks 3M High Density Cross-Connect Modules STG2000 Series The 3M High Density Cross-Connect Modules STG2000 Series are IDC copper cross-connects that can be used in a wide variety of
3M Fibrlok II Angle Fiber Splice 2529-AS 3M Fibrlok 250 µm Angle Fiber Splice 2540-AS
3M Fibrlok II Angle Fiber Splice 2529-AS 3M Fibrlok 250 µm Angle Fiber Splice 2540-AS Instructions January 2009 78-8140-1580-2-C Contents 1.0 Summary...3 2.0 Splicing Set-up...4 3.0 Fiber Preparation...4
New Product Release Summary for 3M Authorized Sales Reps and Distributors 3M Industrial M12 Wiremount Connectors, 3N104 and 3N304 Series
3M Industrial M12 Wiremount Connectors, 3N104 and 3N304 Series Issue Number: 838 Date: December 12, 2012 Product Description The 3M Industrial M12 Wiremount Connectors are an expansion of 3M s extensive
Conductive Pressure Sensitive Cover Tape 2666
3 Conductive Pressure Sensitive Cover Tape 2666 Technical Data January, 2007 Product Description 3M Conductive Pressure Sensitive Cover Tape 2666 is a transparent, conductive polyester film tape with a
3M Connectors for CFast Cards The Next Generation of Removable CompactFlash Storage
3M Connectors for CFast Cards The Next Generation of Removable CompactFlash Storage 3M 2011. All Rights Reserved. Introduction Purpose To explain the features and benefits of the 3M Connectors for removable
Choose the Right Interconnect Solutions for FTTH Drop Cable Installations
Choose the Right Interconnect Solutions for FTTH Drop Cable Installations Business White Paper The Network of Networks Jerry D. Jackson Marketing Manager 3M Communication Markets Division Introduction
3M SlimLine 85ohm Cable Assembly
Product Specifications May 2017 78-5102-0240-7, Rev B Scope This document summarizes test methods, test conditions, and product performance requirements for 3M SlimLine 85ohm Cable Assembly. Reference
Paoloni Rip Kit Installation Instructions
Paoloni Rip Kit Installation Instructions Please note this installation kit is designed for installation only on Paoloni P150, P260, P300 Sliding Table Saws, rip fence. Accurate Technology manufactures
3M Data Center Solutions. Innovation. is the. Solution
3M Data Center Solutions Innovation is the Solution Biometric Physical Security Multi-factor biometric access control reader for data center physical security needs. Air Filtration Filters help provide
General Process Specification for Reflow Soldering of Boardmount 3M Pak Connectors, 3M CF Card Headers and 3M PCMCIA Sockets and Headers
General Process Specification for Reflow Soldering of Boardmount 3M Pak Connectors, 3M CF Card Headers and 3M PCMCIA Sockets and Headers Technical Report November 2004 78-8136-1133-8-A Table of Contents
Paoloni Rip Kit Installation Instructions
Paoloni Rip Kit Installation Instructions Please note this installation kit is designed for installation only on Paoloni P320, P30N, and P30NP Sliding Table Saws, rip fence. Accurate Technology manufactures
3 710 Splicing System 1
3 710 Splicing System 1 3M 710 Splicing System Modules are available for straight, half-tap and bridge splicing Several splice module configurations allow multiple options when designing a communications
MPP200 User s Manual
2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.
3M Workstation Monitor Checker CTE701A User s Guide
3M Workstation Monitor Checker CTE701A User s Guide Table of Contents Section Page Intended Use...3 1.0 Quick Tour of your 3M Workstation Monitor Checker CTE701A...4 2.0 Basics...5 3.0 Metal Ground...5
3M 100G QSFP28 Direct Attach Copper Cable Assemblies, 9Q Series
Product Specifications June 2017 78-5102-0262-1, Rev A 3M 100G QSFP28 Direct Attach Copper Cable Assemblies, 9Q Series Scope This document summarizes test methods, test conditions, and product performance
Crimplok ST* and SC Non-Adhesive Fiber Optic Single & Multi-mode Connectors
Crimplok ST* and SC Non-Adhesive Fiber Optic Single & Multi-mode Connectors Instructions July 2002 78-8073-7660-9-F 1 Contents 1.0 Warnings and Recommendations... 3 2.0 Tool Kit Contents... 4 3.0 Termination...
3M Twin Axial Cable Assembly for Medical Electronics Packaging
3M Electronic Solutions Division 3M Twin Axial Cable Assembly for Medical Electronics Packaging Charlie Staley MEPTEC September 2012 Risers Cards and Extender Cables Sometimes system mechanical configurations
Delta Unifence Kit Installation Instructions
Delta Unifence Kit Installation Instructions Please note this installation kit is designed for installation on the Delta Commercial Unifence (units made between 1993 and current). Accurate Technology manufactures
QUICK START GUIDE. 1. How to register your Camera to Hubble account A. Setting Up the Camera - can be connected via WiFi or LAN
MODEL: FOCUS72 FOCUS72-2 FOCUS72-3 FOCUS72-4 FOCUS72-W FOCUS72-W2 FOCUS72-W3 FOCUS72-W4 QUICK START GUIDE For a full explanation of all features and instructions, please refer to the User s Guide. (available
3M Cold Shrink QS-III Inline Splice Kits 15 kv 5415A, 5416A, 5417A, 5417A-WG, 5418A and 5418A-WG
3M Cold Shrink QS-III Inline Splice Kits 15 kv Data Sheet July 2013 Jacketed Concentric Neutral (JCN) 5415A, 5416A, 5417A, 5418A Concentric Neutral (JCN) 5417A-WG and 5418A-WG! CAUTION Working around energized
Owner s Manual. TSD-ZDC Audio Impedance Combiner/Divider. TSD-ZDC Audio Impedance Combiner/Divider
Owner s Manual 1 Owner s Manual Description The Atlas Sound is a universal impedance divider/combiner for passively summing or splitting of mic or line level signals. Features include four balanced 10K
Everything in its place. OWNER S MANUAL. TRINITY 56 ROLLING WORKBENCH STAINLESS STEEL Model # TLS-4804 (Stainless Body) TLS-4805 (Black Body)
Everything in its place. OWNER S MANUAL TRINITY 56 ROLLING WORKBENCH STAINLESS STEEL Model # TLS-4804 (Stainless Body) TLS-4805 (Black Body) PARTS LIST Your TRINITY 56in Stainless Steel Workbench should
Volition. Modular Managed Switch. 3Innovation ETHERNET/FAST ETHERNET/GIGABIT ETHERNET
Volition Modular Managed Switch ETHERNET/FAST ETHERNET/GIGABIT ETHERNET Revolutionary and robust, the Volition VOL-5000 modular switch from 3M provides the high-speed interconnection needed by organizations
3M PURPLE CLEAN SANDING HOOKIT ABRASIVE DISC
3M PURPLE CLEAN SANDING HOOKIT ABRASIVE DISC Data Sheet Document Control 3M Part No.(s) 3M PRODUCT I.D. 740I or 745I for grades P40 - P80 734U P80 - P180 334U P220 - P800 3M Part Descriptor(s) Select grades
Holz-Her Sliding Table Saw Kit Installation Instructions: For 1243 Rip Kits
Holz-Her Sliding Table Saw Kit Installation Instructions: For 1243 Rip Kits Please note this installation kit is designed solely for installation on Holz-Her Sliding Panel Saws, Model 1243 (may also fit
Delta Unifence Kit Installation Instructions
Delta Unifence Kit Installation Instructions Please note this installation kit is designed for installation on the Delta Commercial Unifence (units made between 1993 and current). Accurate Technology manufactures
3M Cold Shrink QS-III Inline Splice Kits 25/28 kv 5456A, 5456A-WG, 5457A, 5457A-WG, 5458A and 5458A-WG
3M Cold Shrink QS-III Inline Splice Kits 25/28 kv 5456A, 5456A-WG, 5457A, 5457A-WG, 5458A and 5458A-WG Data Sheet July 2013 Jacketed Concentric Neutral (JCN) 5456A, 5457A and 5458A Concentric Neutral (JCN)
3M Fiber Distribution Units 8400 Series. The Network of Networks. Flexibility for. Networks. Growing
3M Fiber Distribution Units 8400 Series The Network of Networks Flexibility for Growing Networks Flexible options to meet growing needs in limited spaces 3M offers a full line of patch panel designs to
Proliphix EPA-60 Installation Guide
Proliphix EPA-60 Installation Guide Rev 1.2 Page 2 of 5 Installation CAUTION THE EPA-60 SHOULD ONLY BE POWERED WITH THE PROLIPHIX POWER SUPPLY INCLUDED WITH THE EPA-60. DO NOT POWER THE EPA-60 WITH ANY
Shop Fox Fence Kit Installation Instructions:
Shop Fox Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Shop Fox Classic Fence. Accurate Technology manufactures kits for other saw fences
Instruction Sheet. PCS Series. Fiber\Cable Management Spool
Instruction Sheet PCS Series Fiber\Cable Management Spool THANK YOU! Thank you for purchasing the PCS Series Fiber\Cabling Management Spool. Please read these instructions thoroughly before installing
Biesemeyer Fence Kit Installation Instructions:
Biesemeyer Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Biesemeyer Commercial Fence. Accurate Technology manufactures kits for other saw
High Shear PSA Cover Tape
3 High Shear PSA Cover Tape Technical Bulletin January, 6 1. Scope End users of high speed pick and place feeders have experienced delamination of the cover tape from the carrier ( pop-off ) after a feeder
3M Fiber Dome Closure Family. Reliable. Fiber. Protection
3M Fiber Dome Closure Family Reliable Fiber Protection More flexibility for your complex fiber optic network A full line of closures and accessories designed to help protect fiber optic facilities in many
DSLR Camera Cage Carbon Fiber Shoulder Rig Kit ( FC-02-CF )
FILMCITY DSLR Camera Cage Carbon Fiber Shoulder Rig Kit 1 DSLR Camera Cage Carbon Fiber Shoulder Rig Kit ( FC-02-CF ) I N S T R U C T I O N M A N U A L All rights reserved. No part of this document may
3M Power Clamp System Power/Signal Distribution I/O Connector System
3M Power Clamp System Power/Signal Distribution I/O Connector System 3M 2011. All Rights Reserved. Introduction Purpose To explain the features and benefits of the 3M Power Clamp System Objectives Highlight
DSLR Camera Cage Shoulder Rig Kit (FC-03)
FILMCITY DSLR Camera Cage Shoulder Rig Kit 1 DSLR Camera Cage Shoulder Rig Kit (FC-03) I N S T R U C T I O N M A N U A L All rights reserved. No part of this document may be reproduced, stored in a retrieval
Extra Large Full Motion TV Mount for Televisions
8008981 TV Size Range: 47 ~ 84 Maximum Weight Capacity: 60 kg/132 lbs Maximum Mounting Pattern: 800 mm x 600 mm (31.4 x 23.6 ) Distance to the Wall: 5.5-45 cm Extra Large Full Motion TV Mount for 47-84
Owner s Manual. TSD-ZDC Audio Impedance Combiner/Divider. TSD-ZDC Audio Impedance Combiner/Divider. AtlasIED.com
Owner s Manual 1 AtlasIED.com Owner s Manual Description The AtlasIED is a universal impedance divider/combiner for passively summing or splitting of mic or line level signals. Features include four balanced
CC186 AND CC186/2 STAND-ALONE OR SYSTEM CLOCK
FN:CC186M2.DOC CC186 AND CC186/2 STAND-ALONE OR SYSTEM CLOCK DESCRIPTION The CC186 is a single sided clock with six, 1.8 inch high digits. The CC186/2 is a double sided clock with six, 1.8 inch high digits
3M Abrasive Systems Clean Sanding Discs and Sheets. Clean. and. Simple
3M Abrasive Systems Clean Sanding Discs and Sheets Clean and Simple When the dust clears, it s the cut that remains Discs cut and last longer when dust isn t loading the cutting surface of the abrasives.
Smart-Box Series. Electronic Lockbox User Manual. Model: 7000,
Smart-Box Series Electronic Lockbox User Manual Model: 7000, 7050 www.nuset.com Information in this document is subject to change without notice. 2010-2011 NuSet, Division of Loyal International, Inc..
SAVE THESE INSTRUCTIONS
and Height Mounts Assembly, Installation and Operating Instructions Model Nos. QL, QLA, ARM250, QLM6 and QLAM6 NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact
Outdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
90130, 90131, POP DISPLAY ASSEMBLY INSTRUCTIONS
90130, 90131, 90132 POP DISPLAY ASSEMBLY INSTRUCTIONS WARNING! Ensure ALL hardware is securely fastened using appropriate tools to prevent damage to the display unit, the products or any injury due to
i-series Videoconference Fixture
TM i-series Videoconference Fixture Operating Instructions 580 Mayer Street, Building #7, Bridgeville, PA 15017 phone 412.206.0106 fax 412.206.0146 www.brightlines.com 2013 Brightline, L.P. Safety To prevent
Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS DN Issue 02 Approval Date yyyy-mm-dd
Nokia Networks Installing and Cabling Flexi Zone Micro High Power 2x20 W BTS DN09229011 Issue 02 Approval Date yyyy-mm-dd Installing and Cabling Flexi Zone Micro High Power The information in this document
Start Here. All-in-One Printer. Print Copy Scan
Start Here All-in-One Printer Print Copy Scan Note: A USB 2.0 cable is required to connect your Kodak All-in-One printer to your Windows or Macintosh OS computer. Available in the Kodak online store or
Demo Kit Quick Start Guide
Near Field Imaging (NFI) Projected Capacitive Touch Screen Systems Read and understand all safety information contained in this document before using this product. Introduction This is intended to help
3M Ribbon Cable Socket and Header, Series 451 & " x.050" (1.27 mm x 1.27 mm)
1 of 8 3M Ribbon Cable Socket and Header, Series 451 & 452.050" x.050" (1.27 mm x 1.27 mm) Product Specification: 78-5102-0091-4 Revised: 05-01-2013 2 of 8 Page Cover Page..... 1 Contents 2 1. Scope......
Owner s Manual. TSD-DCPDV DC Power Distribution with Fixed & Variable Outputs. TSD-DCPDV DC Power Distribution. AtlasSound.com
Owner s Manual with Fixed & Variable Outputs 1 AtlasSound.com Owner s Manual Description The Atlas Sound Variable Block is designed to reduce cost and wiring clutter in installations where multiple DC
User Manual CARFIT Modular System Series CMK
User Manual CARFIT Modular System Series CMK Table of contents Contents CARFIT Modular System CMK Installation Instructions Using the Clamp Assembly as an Example 1 Mounting support 1 2 Mounting support
MPP1700 User s Manual
2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.
DSLR SHOULDER RIG I N S T R U C T I O N M A N U A L. For Demonstration only
DSLR SHOULDER RIG I N S T R U C T I O N M A N U A L For Demonstration only All rights reserved No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by
Dual Component Video Wall Plate 6-RCA AT80COMP6
Dual Component Video Wall Plate 6-RCA AT80COMP6 User Manual www.atlona.com TABLE OF CONTENTS 1. Introduction 2 2. Applications 2 3. Specifications 2 4. Installation 2 5. Safety Information 3 6. Warranty
Flex Pro Series Assembly Guide
ELECTRIC HEIGHT-ADJUSTED SIT TO STAND DESK Table of Contents CAUTION, USE & LIABILITY... 2 PARTS & HARDWARE LIST... 3 PARTS / COMPONENT DIAGRAMS... 3 ASSEMBLY INSTRUCTIONS... 5 BLUETOOTH... 10 TROUBLESHOOTING...
3M Wrist Strap and Ground Monitor 773. User s Guide
3M Wrist Strap and Ground Monitor 773 User s Guide Table of Contents Section Page Safety Information... 2 1 Description... 4 Overview... 4 Performance... 4 2 Installation... 5 Supplied Parts... 5 Wire
Vertical Cable Organizer with D-Ring Hooks - 40U
Vertical Cable Organizer with D-Ring Hooks - 40U CMVER40UD *actual product may vary from photos FR: Guide de l utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario
Instructions. RM3000 Rackmount Kit for TDS3000 Series Oscilloscopes
Instructions RM3000 Rackmount Kit for TDS3000 Series Oscilloscopes 071-0326-00 Copyright Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending.