Floppy Disk To USB. Converter Installation and. Operation Manual
|
|
- Kenneth Turner
- 6 years ago
- Views:
Transcription
1 Floppy Disk To USB Converter Installation and Operation Manual Kit Price $ Plus Shipping
2 Why Should I Change My Floppy Drive To A USB Drive? You won't ever need floppies anymore and yet you'll be able to secure a guaranteed long-term future for your instrument. Disadvantages of legacy diskettes: The old floppy disk drive is slow and takes several seconds to transfer data Hardly available at retailers anymore Sensitive to o Magnetic fields o Dust, oil and other adverse environmental conditions o Mechanical wear and tear Low memory capacity Most salient features: The old floppy disk drive is replaced 1:1. The connections are identical, so no additional changes have to be made to the instrument. The USB Stick at the USB Floppy Converter replaces the old diskette entirely. USB memory components have long life spans and high capacities (Same as 100 floppy disks). The new USB floppy drives and USB memory components are practically immune to impacts, magnetic fields, dust or shock. The contents of 100 floppies can easily be placed on one single USB Stick. That saves a lot of time looking for the correct floppy. The cost to upgrade is considerably less than the cost to purchase a new instrument. The time required to install the upgrade is usually less than an hour on most instruments. Page I
3 Once your new USB Drive is installed, you will be able to plug in your pre-formatted Flash Drive and start saving your presets or recorded music just like they do on the newer instruments. That's Right! Page II We are including, in the cost of the conversion kit, a pre-formatted matching Flash Drive FREE! In Addition: All contact information will be supplied with each kit, so if you have any questions, all you need to do is look at your Flash Drive. The phone number is printed in each one. We don t have a automated phone system, so you will be talking to a real person (American) who speaks and understands the English language. We do not however, speak or understand Spanish. If you have existing floppy disks that you would like to have placed on your Flash Drive, send them to us before we ship your kit and for $1.00 per disk they will be placed on the Flash Drive. Your floppy disks will be returned with your kit. Shipping cost will be as close to the actual cost as possible. It will take approximately 3 weeks to fill your order. If you supply an address or a phone number, we will provide you order status information if a problem developes. works best, as we only have one phone line.
4 Page 1 Above is a picture of my Lowrey Royale (SU-500) powered up with a working 1.4 Meg floppy disk installed. Close up, showing the floppy disk in the working drive. Make sure your disk system works before you start the replacement.
5 Page 2 The back is removed by loosening the five screws across the top with a 1/4 nut driver. The five screws along the bottom must be completely removed. The three screws on each side and the two screws in the middle must also be removed. I suggest you store the loose hardware in a small dish. The right side speaker can easily be removed by disconnecting the two wires on the spade terminals and removing the four 5/16 screws that hold the wooden block in place. Store it in a safe place until it is ready to be re-installed. Pay close attention to the location of the colored wires. The orange wire went to the red dot. (reversing the wires will cause a phase shift). Next unscrew and remove the roll-top stop bumper using an offset Phillips screw driver. A 1/4 nut driver and a 5/16 nut driver were used to remove all other screws.
6 Page 3 Directly under the drive is a 1 hole and the 1/4 screw holding the drive in place. Using a 1/4 nut driver remove this screw.
7 Page 4 Remove the 34 pin data cable and the 4 pin power plug from the back of the floppy drive. Position the cables out of the way and carefully pull the floppy drive up and out of its cage. Pay close attention to the orientation of the red strip on the data cable. It should be replaced on the same side on the new drive. On computer systems the red strip goes to pin 1 of the connector, but on my Royale the cable was installed backwards (on right).
8 Page 5 Place the drives on a flat surface as shown. and remove the four Phillips screws that hold the mounting plate to the floppy drive. Place the removed screws back in the floppy drive (not used). Use the four screws supplied with the USB drive to fasten the mounting plate on the bottom of the new USB Converter.
9 Page 6 Pictured below is the USB Converter connectors. The four pin power connector is on the left and the 34 pin data cable is on the right. Make sure you place the female connector on the male pins, so that each pin goes into its own socket. Caution should be used when installing the power cable to assure that all of the pins are totally seated. Its is obvious, but power should be off during the installation process.
10 Page 7 In this photo you can see the USB Converter has been inserted into the drive cage. It tends to hang-up on the front edge, so make sure it has cleared the front edge and is seated against the felt pads on the front of the drive mounting plate. If it is seated correctly, you will see the hole for the mounting screw when you look up from below the drive location.
11 Page 8 The drive is seated properly and the screw can now be installed in to the bottom of the drive plate. See the photo below.
12 Page 9 Replace the right side speaker using the four 5/16 screws that you removed earlier. Be careful not to over tighten them. They should be snug, but you can strip them if you over tighten them. Next replace the wires that go on the speaker terminals, making sure they are installed on the same terminals they came from. Finally, Using the offset Phillips screw driver, re-install the stop bumper for the roll-top. Do not replace the back until you have double checked your connections with a good strong light. If everything looks correct, you can apply power and turn on the instrument. You should see a double zero appear on the front of new USB Converter. You should also see a period at the bottom and to the right of each digit.
13 Page 10 This is what you should see when power is applied, the red button is pushed in, and there is not a Flash Drive inserted. The two red dots are status indicators. When they go out it is an indication that the Flash Drive has been initialized. Your pre-formatted Flash Drive has 100 floppy disks on it (00-99). Each virtual floppy will operate exactly the same as a physical floppy, except, much faster. The RED button should be out before you insert the Flash Drive in to it s slot. After inserting the Flash Drive, Press the Red button in. The Green light will come on, indicating that the drive is ready.
14 Page 11 The virtual floppy disk can not be changed with the Red button pressed in. To advance to the next desired virtual floppy, make sure no disk activity is taking place. Then press and release the Red button. It will stick out. To move to the next virtual floppy press the Right Black button one time. The display should read 01. Continuously pressing the right button will sequence the right display digit 2, 3, 4, 5, 6, 7, 8, 9, and back to 0. Performing this action on the Left Black button will sequence the left digit in the same way. Once the desired virtual floppy has been selected, the Red button must be pressed in to allow the Flash Drive to transfer data. The Green light will come back on, indicating that the selected virtual floppy is ready to be used.
15 Page 12 In this photo the converter is telling us what has occurred. The Green light is lit, so we know that the drive is ready to transfer data. We know that while the Red button was depressed, the Right Black button was depressed five times and the Left Black button was pressed twice. Thus, the 25 shown on the display. Now, as soon as the dots go out, with the Red button pressed in, and the Green Ready light lit, the drive is ready for data to be transferred between virtual floppy 25 and the instrument. Before the Flash Drive can be removed, all data transfer activity needs to have been completed and the Red button needs to be in the Out position. That can be verified by observing that the Green light in NOT lit. When data is being transferred, the Flash Drive light blinks at a fast rate. Once the transfer has been completed, the light will slowly go back and forth from bright to dim. Remove the Flash Drive when the light is dim. NOTE: CAUTION - CAUTION - CAUTION Removing the Flash Drive during data transfer may cause the Flash Drive to be damaged. No damage to the USB Converter will occur if the Flash Drive is removed during a data transfer.
imac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationNov. 07, 2013 p. 5 - changed the B axis unit value to from Changed by Randy per Frank s request.
Correction notes Nov. 07, 2013 p. 5 - changed the B axis unit value to 45.1389 from 40.0000. Changed by Randy per Frank s request. Jan. 22, 2018 p. 5 - changed the B axis unit value and corresponding picture
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationinto the EMU E4 Classic and E4 Platinum Samplers
Installing the CF-CARD SCSI Card Reader/Writer Drive into the EMU E4 Classic and E4 Platinum Samplers Thank you for purchasing the CF-CARD Internal Card Reader Drive Installation Kit from SCSICardReaders.com.
More informationFloat Pod Installation Manual
Float Pod Installation Manual TABLE OF CONTENTS What to do before receiving the pod..page 3 Receiving the pod...page 5 Installing UV..Page 9 Control Box. Page 12 Intercom....Page 14 Audio.. Page 16 Pod
More informationAdding or Replacing a PCI Card
Caution There are static-sensitive electronics inside the unit. Before you handle any parts, make sure you are working at a static-controlled workstation and that you are properly grounded. Three PCI cards
More informationFRU Installation Notes Virtuo Monitor Glass Replacement
January 2016 900975-001 Rev 00 FRU Installation Notes Virtuo Monitor Glass Replacement Purpose How to replace the touch screen glass on a Virtuo This document is for these components or categories Expected
More informationWORDSYNC ADDENDUM to the SupraDrive Operator s Manual
WORDSYNC ADDENDUM to the SupraDrive Operator s Manual Congratulations on your purchase of a SupraDrive Hard Card or WordSync Interface Kit for your Amiga 2000 computer. Your new hard drive system will
More informationInstructions for installing your QuiltCam on your Gammill quilt machine.
Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video
More informationAssembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #
Assembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #7521002 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how
More informationReplacing the Encoder Strip
6-1-11. Replacing the Encoder Strip The following describes the procedure for replacing the Encoder Strip. Refer to the diagram below for identifying the parts and their positions. (The numbers shown in
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationRevised: Page 1
Brought To You By And Designed By: Revised: 2017-05-07 Page 1 Features Of The Universal PSU Kit: Fits all standard Apple II and /// Power Supply Enclosures. (all parts included, user supplies household
More informationWritten By: Ben Eisenman
iphone 3GS Rear Panel Replacement Replace a broken rear case on your iphone 3GS. Written By: Ben Eisenman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION The plastic rear half of the iphone.
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More information*E * E E0606
75000 SERIES B Instrument BASIC Installation Note Copyright Agilent Technologies, Inc., 1990-2006 *E1300-90020* E1300-90020 E0606 Manual Part Number: E1300-90020 Printed: June 2006 Edition 1 Rev 2 Microfiche
More informationTIVO UPGRADE INSTRUCTIONS (c) , Adberg Consulting LLC. All rights reserved.
TIVO UPGRADE INSTRUCTIONS (c) 2001-2003, Adberg Consulting LLC. All rights reserved. Instructions for Series 1 DirecTV/TiVo GXCEBOT TWO-DRIVE REPLACE upgrade Color instructions are also available at http://www.weaknees.com/upgrade_instructions.php
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationTRC-190 User s Manual
User s Manual Edition 3.2, May 2017 www.moxa.com/product 2017 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used only
More informationMacBook Core 2 Duo Display Replacement
MacBook Core 2 Duo Display Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION Change out the entire display assembly, including the inverter, Airport antennas, hinges
More informationField Update Guide. for Raven Viper Pro
Field Update Guide for Raven Viper Pro Introduction The field update kit (P/N 117-0171-467) is designed to allow the Raven Viper Pro to utilize the automatic power down feature without returning the console
More informationRoyal RVV-500 (B) Retrofit Kit
Optipay BV/RC/CC into a Non-Fascia Vending Machine This document contains information for installing and configuring the JCM Optipay DBV-01 Bill Validator, RC-10 Bill Recycler and A-66 Coin Changer into
More informationControl Box Setup - PRSalpha
888-680-4466 ShopBotTools.com Control Box Setup - PRSalpha Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Parts List: Hooking Up a PRSalpha Gantry Tool Powering the
More informationBL-FLOWSTN-P FlowStation Module Installation Guide
Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationPandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006
Pandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how to
More informationRemoval and Replacement of the Serrano and Corsica Boards
Removal and Replacement of the Serrano and Corsica Boards 1. Purpose The purpose of this procedure is to document the removal and replacement of the Serrano and Corsica board of the Deko/Thunder Assemblies.
More informationOwner s s Manual. G5 SATA Double Drive Internal Mounting Kit. Apple Macintosh G5. Add 2 SATA drives to the G5
Owner s s Manual Add 2 SATA drives to the G5 G5 SATA Double Drive Internal Mounting Kit Apple Macintosh G5 SATA (Serial ATA) 2 Internal Drive System Table of Contents User Guide Page How SATA (Serial ATA)
More informationimac Intel 27" Retina 5K Display CPU Replacement
imac Intel 27" Retina 5K Display CPU Replacement Replace or upgrade the CPU in your imac Intel 27" Retina 5K Display. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION
More informationTRC-190 User s Manual
First Edition, November 2008 www.moxa.com/product 2008 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. The software described in this manual is furnished under a license agreement
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More informationInstalling the Server into a Rack
Installing the Server into a Rack Note These instructions apply to multiple models; illustrations may vary slightly. Rack Mount Kit Inventory Before installing the chassis on a standard 4-post rack, make
More informationHow To Install: C4000 EMV Upgrade Kit
How To Install: C4000 EMV Upgrade Kit IMPORTANT: Before proceeding with installation please verify you have the current card reader bezel in the kit. Correct bezel will have a small eject pin hole below
More informationHP Pavilion 15 P Series Hard Drive Replacement
HP Pavilion 15 P Series Hard Drive Replacement This guide will show you how to to replace the hard drive in your HP Pavilion P Series laptop. Written By: Nick ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationMac Mini Mid 2011 SSD Dual Drive Installation
Mac Mini Mid 2011 SSD Dual Drive Installation Install a second hard drive in your mid 2011 Mac Mini. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 19 INTRODUCTION Use this guide to install
More informationEnglish. Exchanging the Main Board grandma full size up to s/n 903
Service nual English Exchanging the Main Board grandma full size up to s/n 903 Exchanging the Main Board The following work must be performed of trained and qualified personal only! Disobeying the instructions
More informationIoline CrystalPress. Quick Start Guide
Ioline CrystalPress Quick Start Guide The Quick Start Guide is intended to help a new user of the Ioline CrystalPress get everything setup and running quickly. Please note that there are important notices,
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationANIxx. Installation Manual.
ANIxx Installation Manual www.audac.eu Introduction WaveDynamics Dante audio network interface The ANIxx are Dante audio network interfaces for use with WaveDynamics supporting amplifiers, supporting two
More informationSSD Dual Drive Installation
SSD Dual Drive Installation Replace the optical drive in your imac Intel 21.5". Written By: Dozuki System 2017 guides.crucial.com Page 1 of 18 INTRODUCTION imac won't read disks? Use this guide to replace
More informationINSTALLING ColorDMD LED DISPLAY IN BALLY GAMES WITH DISPLAY ON LAMP BOARD
INSTALLING ColorDMD LED DISPLAY IN BALLY GAMES WITH DISPLAY ON LAMP BOARD These instructions are for mounting a ColorDMD LED display in a Bally game that has the display mounted on the swinging backbox
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationProcedure to Replace a TCD DPM with an IS TCD DPM in a Maxum or Maxum II Analyzer
Procedure to Replace a TCD DPM with an IS TCD DPM in a Maxum or Maxum II Analyzer Difficulty Level: Medium Estimated time to execute: 1 Hour Revision History Issue Date Reason 001 1/31/2017 Initial Issue
More informationToshiba Satellite A215 S4697 Screen
Toshiba Satellite A215 S4697 Screen Replacement When your computer screen is cracked or does not work anymore, it may need a new screen. Written By: Carlos ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15
More informationTURN-O-MATIC INSTALLATION GUIDE
TURN-O-MATIC INSTALLATION GUIDE WIRELESS SYSTEM WIRELESS SYSTEM (1) Dispenser (1) Dispenser Mounting Bracket (3) Large Slotted Screw (2) Large Slotted Bolt (2) Nut (1) Display Wall Mount Bracket (1) Wireless
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationMacBook Core 2 Duo Clutch Cover
MacBook Core 2 Duo Clutch Cover Replacement Replace the clutch cover on your MacBook Core 2 Duo. Written By: Ben Eisenman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Replace the curved
More informationTABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION
S6 USER S MANUAL TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION SECTION 4 SLIDE CONFIGURATION ACCESSORIES SECTION 5 RACK MOUNT
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationPRODUCT MANUAL Duet DMX & Wireless RGB-W Controller
Product Description Solid Apollo LED s new wall mounted Duet DMX & RGB-W LED Controller has been created to control LED light fixtures in three different ways. Users can independently control DMX enabled
More informationCPU fan has a power connector which needs to be connected to CPU fan power socket on your motherboard as shown on the image above.
The first thing you should do is unpack your ATX case. Take off the cover of your case so that you can access the inside. Place the case on a desk so that you are looking down towards the open case. Your
More informationHP UPS R/T3000 G2. Overview. Precautions. Kit contents. Installation Instructions
HP UPS R/T3000 G2 Installation Instructions Overview The HP UPS R/T3000 G2 features a 2U rack-mount with convertible tower design and offers power protection for loads up to a maximum of 3300 VA/3000 W
More informationInstalling PRO/DGX or Pro Soloist MIDI interface. R Grieb 9/08/2017
Installing PRO/DGX or Pro Soloist MIDI interface. R Grieb 9/08/2017 Please read these instructions before purchasing the MIDI interface, to make sure you are comfortable performing the necessary steps.
More informationFitting An Emulator into the Yamaha AR Organ
Fitting An Emulator into the Yamaha AR Organ As performed by Les White and Frank Kemplay May 2011 On the upper rear panel remove the top line of 3 screws to allow removal of the top board assemblywhich
More informationiphone 3G Headphone Jack Replacement Replace a broken audio port in an iphone 3G. Written By: irobot ifixit CC BY-NC-SA
iphone 3G Headphone Jack Replacement Replace a broken audio port in an iphone 3G. Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION No audio? Replace the headphone jack! TOOLS:
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationimac Intel 21.5" EMC 2389 Stand Replacement
imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION
More informationEasyBuild- Assembly Manual. Enclosure for Desktop CNC /3D Systems STEPCRAFT 300/ 420
EasyBuild- Assembly Manual Enclosure for Desktop CNC /3D Systems STEPCRAFT 300/ 420 Original assembly manual date of 01.07.2017 Dear customer, thank you very much for purchasing our high-quality kit of
More informationRevision History E F G H J K Revision Description: K > Allegion Rebranding.
Notes: Enter any notes here. These notes must include: how many sides of the paper are printed ink color (usually black, may also be one or two specific colors, such as a Pantone value, or 17.000 8.500
More informationProcedure to Upgrade from B&W Maintenance Panel to TIB Color Touchscreen Door in a Working Maxum or Maxum II Analyzer Equipped With a SYSCON2
Procedure to Upgrade from B&W Maintenance Panel to TIB Color Touchscreen Door in a Working Maxum or Maxum II Analyzer Equipped With a SYSCON2 Difficulty Level: High Estimated time to execute: 3 Hours Revision
More informationGetting Started. Here's how to get started using your Zip 250 drive: 1. Unpack the Zip 250 drive and accessories.
Getting Started IMPORTANT! Before installing or using your Zip 250 drive, read and follow the USB guidelines to ensure reliable performance of your USB devices. Here's how to get started using your Zip
More informationFigure 4-29 Removing the CPU compartment cover
4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment
More informationWhitebox TM Developer s Guide
Whitebox TM Developer s Guide Revision 1.0 April 22, 2016 c 2016 Arx Pax Labs, Inc. 1 Contents 1 Introduction 3 2 Equipment Not Included 3 3 How to Disassemble the Whitebox 4 4 ESC Programming 9 5 Teensy
More informationPackard Bell Vibe 300 Disassembly Manual
Packard Bell Vibe 300 Disassembly Manual 1 Table of Contents Overview 2 Technician Notes 2 Disassembly Instructions 2 Reassembly Instructions 2 Required Tools 2 Removing the Bottom Cover 3 Removing the
More informationUR51 Industrial Cellular Router
UR51 Industrial Cellular Router Quick Start Guide 1 Ursalink Technology Co., Ltd. Welcome Thank you for choosing Ursalink UR51 industrial cellular router. This guide describes how to install the UR51 and
More informationWritten By: senordingdong
Installation of the UniMac V4 adapter into the Apple imac Intel 17". This enables the usage of non OEM LCD panels, and offers an otherwise unavailable Full HD upgrade. This used for repair of the common
More informationIPC194. ipconv Protocol Converter
IPC194 General Operating, Maintenance and Installation Manual ipconv Protocol Converter D-91056 Erlangen Phone: +49 9131 7677 47 Fax: +49 9131 7677 78 Internet: http://www.ipcomm.de Email: info@ipcomm.de
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationDell Inspiron Mini 10 RAM Replacement
Upgrade or replace RAM to boost speed and performance. Written By: Danielle Jarecki ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION This guide will give step-by-step instructions on how to
More informationLED Maintenance Instructions
Chapter 5 LED Maintenance Instructions This guide describes the maintenance procedures for the LED portion of your DayStar or TekStar sign. 1.800.237.3928 stewartsigns.com Rev1802 Intentionally Left Blank
More informationInstallation, Usage and Maintenance Guide for Kit 1
Installation, Usage and Maintenance Guide for Kit 1 July 2013 WARNING Read this document before installing or using Data East/Sega Speaker Light Mod by Pinballtoppers Improper installation, improper use,
More informationADD-ON INSTALLATION GUIDE XEN-LS. apricot MITSUBISHI ELECTRIC
ADD-ON INSTALLATION GUIDE XEN-LS apricot MITSUBISHI ELECTRIC Intel is a registered trademark, and 80386SX, 80387SX, 80486SX and 80487SX are trademarks, of Intel Corporation. AT is a trademark of International
More informationMacBook Unibody Model A1278 SSD Dual Drive
MacBook Unibody Model A1278 SSD Dual Drive Installation Use this guide to install a second hard drive in place of the optical drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 13 INTRODUCTION
More informationP160 User s Manual Manuel de l utilisateur Anwenderhandbuch Manuale per l operatore Manual del usuario
P10 User s Manual Manuel de l utilisateur Anwenderhandbuch Manuale per l operatore Manual del usuario At Antec, we continually refine and improve our products to ensure the highest quality. So it's possible
More informationimac Intel 21.5" EMC 2389 SSD Dual Drive
imac Intel 21.5" EMC 2389 SSD Dual Drive Installation Use this guide to install a second SSD in place of the optical drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 17 INTRODUCTION There
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationSerial ATA Hot Swap Drive Cage Upgrade Kit for: Intel Server Chassis SC5200 Intel Server Chassis SC5250-E
Serial ATA Hot Swap Drive Cage Upgrade Kit for: Intel Server Chassis SC5200 Intel Server Chassis SC5250-E A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/Products Order Number:
More informationJuly Manual 10-slide disk outdoor viewer
Ing. J. de Wijs. Populierstraat 44, 4131 AR Vianen, the Netherlands Tel/Fax. +31 (0)347-372242 e-mail: info@dewijs-3d.com Website: www.dewijs-3d.com Design and production of stereoscopic instruments. July
More informationAssembly and Setup Manual
M-12 Series Copyboard / C-12 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-12 series Copyboard and C-12 series Captureboard. (The copyboard and/or
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More informationCygnos360 V2 Installation Manual
VERSION 1.0. - OKTOBER, 2009 www.cygnos360.com Contents: 1. What you need...2 1.1. Tools...2 2. Preparation...3 2.1. Preparing the solder points...3 3. Installing in your Xbox360...4 3.1. Installing the
More informationOpenSprinkler v2.1u Build Instructions
OpenSprinkler v2.1u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationA TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address
Requirements A TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address Power Up A Reader with an Ethernet adaptor installed and the network cable
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationimac Intel 20" EMC 2105 and 2118 SSD
imac Intel 20" EMC 2105 and 2118 SSD Installation Replace the hard drive in your imac Intel 20" EMC 2105 and 2118. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 15 INTRODUCTION Upgrade your
More informationThanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443
Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. PARTS LIST: 2 Metal Plate Stands 5 Greenery
More informationJippo Play - Installation Manual Page 1 INSTALLATION MANUAL. Intro Camera Operation Installation - Wrangler JK... 2
Jippo Play - Installation Manual Page 1 INSTALLATION MANUAL CONTENTS Intro... 1 Camera Operation... 2 Installation - Wrangler JK... 2 Jippo Play Configuration... 6 VES Installation... 7 Camera Installation...
More informationJBL Flip 2 Battery Replacement
JBL Flip 2 Battery Replacement This guide will walk you through replacing the battery for this device. Written By: Jonathan Wear ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION This guide will
More informationThank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com.
Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Please check out our ebay auctions for more great deals on Factory Service Manuals: servicemanuals4u Dell Latitude
More informationOpenSprinkler v2.2u Build Instructions
OpenSprinkler v2.2u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationPAA CNC Control Retrofit Kit for Flow Waterjet Pro 1313, 1318 and 2031 models with Higerman HI-800 controls
PAA CNC Control Retrofit Kit Contents Overview... 2 Kit Contents... 2 Hardware... 2 Software... 2 Miscellaneous Small Parts... 2 Installation... 2 Tools and Materials... 2 Preparation... 3 Operator s Station...
More informationH3C S7503-S7506-S7506R Ethernet Switches Power Distribution Box Installation Guide
H3C S7503-S7506-S7506R Ethernet Switches Power Distribution Box Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Manual Version: T2-08050R-20070521-C-1.01 Copyright 2006-2007,
More informationNvidia Shield Tablet K1 Micro USB Port Replacement
Nvidia Shield Tablet K1 Micro USB Port Replacement This is a guide for the removal and replacement of the Micro USB Port. Written By: Ryan Butler ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION
More informationimac Intel 27" EMC 2429 SSD Dual Drive
imac Intel 27" EMC 2429 SSD Dual Drive Installation Install the dual hard drive kit in an imac Intel 27" EMC 2429. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 22 INTRODUCTION This guide
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationInstructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only)
Instructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only) **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit Kit Contents PART NAME
More informationDell Latitude V710/V740 Service Manual
Dell Latitude V710/V740 Service Manual Dell Latitude V710/V740 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification System Components
More information