PMCG - MANUAL PMCG ORIGINAL INSTRUCTIONS. Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland

Size: px

Start display at page:

Download "PMCG - MANUAL PMCG ORIGINAL INSTRUCTIONS. Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland"

Logan Robinson
6 years ago
Views:

1 PMCG ORIGINAL INSTRUCTIONS Manufactured: Designed: Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland info@preservatech.eu Preservatech Inc Toronto, Canada info@preservatech.com 1

2 Table of Contents INTRODUCTION... 3 DIMMENSION... 4 Packing List... 4 INSTALLATION... 5 SETTING UP... 6 ALARM CONNECTION... 7 DATA LOGGER... 7 MASTER SLAVE CONFIGURATION... 8 A SETTING MODE... 8 B- FULL MASTER/SLAVE MODE... 9 Setting machine to be used as Master or Slave Setting Mode B. FULL MASTER/SLAVE MODE PROGRAMMING MANUAL USER MODE PROGRAMMING MODE PARAMETERS LIST SETTING DATE/TIME MODE DATE/TIME PARAMETERS LIST Network connection Shipping and storage LIMITED MICROCLIMATE GENERATOR WARRANTY Declaration of Conformity

INTRODUCTION Preservatech's PMCG generator is a miniature humidity control device for museum showcases and similar small sealed enclosures.

3 INTRODUCTION Preservatech's PMCG generator is a miniature humidity control device for museum showcases and similar small sealed enclosures. This unit can reliably control humidity for individual well sealed enclosures. When properly installed, this microclimate control system will typically maintain the relative humidity level in a sealed enclosure within two percent (or less) of an operator determined value. Depending upon the ambient temperature conditions and enclosure construction, relative humidity levels of less than twenty to over sixty percent can be attained. This unit will work only with high quality display cases with an air change rate of 0.2 per day or better. This manual will assist you in installing and setting up the unit as well, it contains complete instructions on operating the unit. Please note the cautions and warnings, as the unit may not provide optimum performance if all directions are not carefully followed 3

4 DIMMENSION PACKING LIST Every machine shipment consists of: 1. PMCG generator. (1 pc) 2. Silicone hose for connecting to display case (2 m) 3. Through wall air connector (2 pcs) 4. Humidity sensor. (1pc) 5. Power cord. (1 pc) Optional (not included in standard package) 6. External alarm cable and LED. 7. External booster fan 4

5 INSTALLATION The PMCG unit re-circulates air inside the case. Installation is very simple and includes: - Connection of the PMCG unit to the case, using two flexible hoses made of silicone (or other material approved by conservator), hoses outside diameter: 7/8-22 mm (included) - Hose connecting machine OUT port with the case should be as short as possible, input hose can be longer. - Installation of the RH sensor inside the case (to get most stable humidity inside the case, sensor should be located close to the air input but not directly in the air stream). - Connection to a standard, grounded power outlet VAC. WARNING: POWER OUTLET MUST BE PROPERLY GROUNDED. - Setting up proper RH level (see next chapter) DISPLAY CASE Distance between air fittings, should be as far away as possible SENSOR PMCG 5

(left bottom button) and "ALA" - out of range alarm deviation (center button). See detailed instruction below.

6 SETTING UP The machine is controlled by a microprocessor located at the front of the machine. Using 5 buttons, located on the right side of the display, it is possible to switch display between, "RH" - actual value of RH measured by machine sensor (left top button) "SET" - target RH value (left bottom button) and "ALA" - out of range alarm deviation (center button). See detailed instruction below. For more comprehensive instruction of microprocessor programming, please see our "PMCG - Programming Manual". Shows actual RH value measured by machine sensor RH-measured humidity-read only SET-target humidity Target RH value. Press GREY button, change value using up/down buttons, save with GREY button INCREASE/DECREASE VALUE ALA-out of range alarm Value offset for OUT OF RANGE ALARM. INCREASE/DECREASE VALUE Alarm will be triggered when RH>(SET+ALA) and/or when RH<(SET-ALA) 6

ALARM CONNECTION PMCG machines have an alarm connector on the back of the machine. Optionally the machine can be shipped with 2 meters of cable and a small red LED light.

LED light is powered by 12 VDC and LED's leads should be DATA LOGGER Some of the machines are equipped with a built-in data logger.

Data written on the SD card, can be read in our free software or in any other software able to read CSV files (eg.

7 ALARM CONNECTION PMCG machines have an alarm connector on the back of the machine. Optionally the machine can be shipped with 2 meters of cable and a small red LED light. LED can be located away from the machine, to indicate "RH OUT OF RANGE" status. connected properly: RED to BROWN and BLACK to BLUE. LED light is powered by 12 VDC and LED's leads should be DATA LOGGER Some of the machines are equipped with a built-in data logger. The data logger records the actual measurements on a SD card (not included). Time intervals can be changed between 1 and 60 minutes in 1 minute increments, please see "Programming Manual". Data written on the SD card, can be read in our free software or in any other software able to read CSV files (eg. Excell) IMPORTANT: SD Card used in our data loggers must be formatted as FAT32 file systems. Other file systems are not compatible with data loggers. For properly working data logger, Date and Time as well as LOG parameter, must be properly set. Please see pages for instruction how to set Time, Date and LOG parameters. LOG represents interval between writing data od SD Card in minutes. LOG = 0 Data logger is turned off. 7

8 MASTER SLAVE CONFIGURATION PMCG machines can be set in Master-slave configuration. There are two possible Master/Slave modes: A SETTING MODE IN THIS MODE, ANY PMCG AND/OR MINI ONE UNITS CAN BE CONNECTED TOGETHER. One machine is set as a Master unit then connected to the remaining machine(s) by Ethernet cable using cable splitters. Slave units (receiving units) have their own sensors. The Master unit only sends a signal of the set value to the slave controllers. MASTER SLAVE SLAVE SLAVE Ethernet This mode is good if there are many PMCG s (or Mini Ones) and all of them should be set to the same value. Master units work as a remote: setting all other units to the same humidity value. 8

9 B- FULL MASTER/SLAVE MODE IN THIS MODE, ONLY SAME MODEL MACHINES CAN BE CONNECTED. One machine is set as Master and one is set as Slave. Slave unit doesn t have a sensor and works exactly as the Master unit. MASTER SLAVE Ethernet This mode is best if two machines are working with a single, larger display case. 9

10 SLAVE MASTER PMCG - MANUAL Setting machine to be used as Master or Slave Any machine can be set as Master or Slave. To set a machine to work as Master/Slave, few parameters in the controller software must be changed. Setting Mode 1. All machines to be part of master/slave configurations need to be connected using standard Ethernet cables and cable splitters (easily available in any computer store). Connector is located on the back wall of the machine and is marked as NETWORK. All machines are connected to the cases in the same way as in independent mode. 2. Master unit need to be reprogrammed as follows: Parameter Value to be set Factory set value Notes Slave unit(s) needs to be reprogramed as follows: Parameter Value to be set Factory set value Notes Each slave unit needs to have own unique address. 0 0 No change to factory set 0 0 No change to factory set 0 0 No change to factory set 10

The Slave unit will receive all readings from the Master unit and mimic the Master unit operation. Controller on the Slave unit will not work and sensor on slave unit is disconnected.

11 Every time, set value on MASTER UNIT will change, all slave units will change their own set value to match master value. PLEASE SEE PROGRAMMING CHAPTER FOR EXACT INSTRUCTION HOW TO ENTER PROGRAMMING MODE. B. FULL MASTER/SLAVE MODE In this configuration, only one pair of machines can be connected (one Master, one Slave). The Slave unit will receive all readings from the Master unit and mimic the Master unit operation. Controller on the Slave unit will not work and sensor on slave unit is disconnected. Display on Slave unit will change to S. Machines can be connected to the controlled case in series or parallel. In Series Hose from the case is connected to the Air from case connector on the Master unit, Air to case on Master is connected to the Air from case on the Slave unit and Air to case on Slave is connected to the display case. (Display case needs a total of two air connectors 1 per unit) Parallel Both machines are connected to the display case same way as single machine. (Display case needs a total of 4 air connectors 2 per unit) Both machines need to be connected together using standard Ethernet cable. Connector is located on the back wall of the machine and is marked as NETWORK. ONLY MASTER UNIT NEEDS SENSOR CONNECTED. 11

12 SLAVE MASTER PMCG - MANUAL 1. Master unit needs to be reprogrammed as follows: Parameter Value to be set Factory set value Notes This number must be same as parameter Adr on slave unit Slave unit(s) needs to be reprogramed as follows: Parameter Value to be set Factory set value Notes No change to factory set 0 0 No change to factory set 1 0 When the controller displays S the machine is working as a full slave unit. In this mode, both machines are controlled by master unit. PLEASE SEE PROGRAMMING CHAPTER FOR EXACT INSTRUCTION HOW TO ENTER PROGRAMMING MODE. 12

13 PROGRAMMING MANUAL USER MODE Shows actual RH value measured by machine sensor RH-measured humidity-read only SET-target humidity Target RH value. INCREASE/DECREASE VALUE ALA-out of range alarm Value offset for OUT OF RANGE ALARM. Alarm will be trigered when RH>(SET+ALA) and/or when RH<(SET-ALA) INCREASE/DECREASE VALUE 13

Entering programming mode Hold 2 buttons about 3 sec SELECTING PARAMETERS MOVE THROUGH PARAMETERS LIST BACK TO USER MODE EDIT

14 PROGRAMMING MODE Under normal circumstances, there is no need to make any changes to this portion of the controller software. Please be careful before making any changes. Please contact for help. Entering programming mode Hold 2 buttons about 3 sec SELECTING PARAMETERS MOVE THROUGH PARAMETERS LIST BACK TO USER MODE EDIT PARAMETER EDITING PARAMETER INCREASE/DECREASE VALUE BACK TO PARAMETER SELECT WITHOUT SAVING VALUE SAVE VALUE AND BACK TO PARAMETER SELECT 14

PARAMETERS LIST Measured Temperature READ ONLY Measured

(target humidity) same as "SET" in user mode Out Of Range alarm

for replacement sensors) Control Mode 1- DH 2- DD 3- HH

Entering Setting Time mode See next page for more info Value: 0

See Operation Manual: Master Slave Configuration Value: 0-99

See Operation Manual: Master Slave Configuration Value : 0 or 1

15 PARAMETERS LIST Measured Temperature READ ONLY Measured HumidityREAD ONLY Same as "RH" in user mode Humidity preset (target humidity) same as "SET" in user mode Out Of Range alarm offset same as "ALA" in user mode Calibration data 1 lower number noted on RH sensor label. (only for replacement sensors) Calibration data 2 higher number noted on RH sensor label. (only for replacement sensors) Control Mode 1- DH 2- DD 3- HH Calibration Offset Can be set to minimise difference between machine reading and third party probe. Network Address Logging interval in minutes 0=logger is off Entering Setting Time mode See next page for more info Value: 0 or 1 Sets Master mode. See Operation Manual: Master Slave Configuration Value: 0-99 Sets Master mode. See Operation Manual: Master Slave Configuration Value : 0 or 1 Sets Slave mode See Operation Manual: Master Slave Configuration THIS PARAMETER MUST BE SET ACCORDING TO THE MODEL, PRINTED ON THE BACK WALL OF THE MACHINE. Software version READ ONLY 15

selected sets TIME/DATE and goes back to programming mode EDIT PARAMETER INCREASE/DECREASE

16 SETTING DATE/TIME MODE for models with SD Logger ENTERING PROGRAMMING MODE PARAMETER SELECT MOVE THROUGH PARAMETERS LIST BACK TO PROGRAMMING MODE EDIT PARAMETER OR if "SET" parameter selected sets TIME/DATE and goes back to programming mode EDIT PARAMETER INCREASE/DECREASE VALUE BACK TO PARAMETER SELECTION WITHOUT SAVING BACK TO PARAMETER SELECTION 16

17 DATE/TIME PARAMETERS LIST YEAR MONTH DAY HOUR MINUTES SAVES ALL SET PARAMETERS 17

18 Network connection. For network connection and setup, please consult our Network Manual available from our download page. Shipping and storage. Product should be stored in clean area with temperature between 5 C 30 C and relative humidity below 80%. All cables, hoses and attachments must be disconnected and machine should be placed within a clear plastic bag. If shipping is necessary, original packing is the best solution. Otherwise, machine must be shipped in a box properly cushioned with bubble foil, styrofoam chips or other packing material preventing physical damage to the machine case. 18

19 LIMITED MICROCLIMATE GENERATOR WARRANTY This quality product is warranted to be free from manufacturer's defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer, and in accordance with the Requirements for Proper Operation as outlined in this Installation and Operating Manual. This warranty is available only to the client to whom the unit was originally sold by authorized distributor of Preservatech Inc or Preservatech Europe sp z o.o.., and is non-transferable. TERMS OF WARRANTY During the first two years, any electrical parts of this product found to be defective, including any sealed system units, will be repaired or replaced, at warrantor's option, at no charge to the ORIGINAL purchaser. To obtain service, contact Preservatech at the address below, who will provide you with instructions. Service must be performed by a qualified service technician, or with the express permission of Preservatech If service is performed on the units by anyone other than an authorized service depot or agent, all obligations of Preservatech under this warranty shall be at an end. EXCLUSIONS Save as herein provided by Preservatech, there are no other warranties, conditions, representations or guarantees, express or implied, made or intended by Preservatech or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Preservatech shall not be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and save harmless Preservatech from any claim for damages to persons or property caused by the unit. GENERAL PROVISIONS No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following: 1) Damage in transit or when moving the appliance. 2) Improper power supply such as low voltage, power surges, defective wiring or inadequate fuses. 4) Accident, alteration, abuse or misuse of the appliance such as an inadequate supply of cooling air, or abnormal operating conditions. 5) Use of a unit that has been optimized for a particular application in another application that has not been approved by Preservatech 6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc, 7) Service calls resulting in customer education. WARRANTY SERVICE Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present a facsimile of the cover of this document to our AUTHORIZED SERVICE DEPOT. Please contact our head office for service instructions. info@preservatech.com 19

Declaration of Conformity DECLARATION OF CONFORMITY Product: PMCG Humidity Generator Models: PMCG DH, PMCG-DD, PMCG-HH Description: Constant humidity generator designed for controlling relative

20 Declaration of Conformity DECLARATION OF CONFORMITY Product: PMCG Humidity Generator Models: PMCG DH, PMCG-DD, PMCG-HH Description: Constant humidity generator designed for controlling relative humidity inside a museum display cases. Manufacturer: Preservatech Europe sp z o.o. Rowna 1, Bydgoszcz Country of origin: Poland The above mentioned product complies with following regulation: EU Low Voltage Directive 2006/95/EC EU Electromagnetic Compatibility Directive 2004/108/EC Harmonised Standards: EN : A2:2008, EN : A1: 2011, EN : 2007 Signed DEC 11, 2015 in Bydgoszcz Jan Maternicki president 20

PMCG II - MANUAL PMCG ORIGINAL INSTRUCTIONS. Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland

PMCG II - MANUAL PMCG ORIGINAL INSTRUCTIONS. Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland PMCG ORIGINAL INSTRUCTIONS Manufactured: Designed: Preservatech Europe sp z o.o. Równa 1, 85-846 Bydgoszcz, Poland info@preservatech.eu Preservatech Inc Toronto, Canada info@preservatech.com 1 www.preservatech.com