Index. End Launch Connector Series. End Launch Connectors (67 GHz)... Page. Installation Procedure End Launch Connector Dimensions...
|
|
|
- Toby Willis
- 6 years ago
- Views:
Transcription
1 Connector Series Index (67 GHz).... Page Specifications Introduction Procedure Connector Dimensions Connector Numbers Typical Test Data
2 Specifications Applications Transition Block Standard 3/8 Square Flange Connector Board Design Assistance Available. Contact Factory. Grounded Coplanar Clamp Plates Microstrip with Top Ground Electrical: Mode Free Through: 27.0 GHz (SMA) 40.0 GHz () 50.0 GHz () 67.0 GHz (1.85 mm) Low VSWR Low Insertion Loss Materials / Construction: Connector: (see appropriate connector section for materials & construction) Transition Block & Clamp Plates: Housing: Brass Alloy UNS C36000 Per ASTM B16, Nickel Plate Per ASTM 2404B Transition Pin: Beryllium Copper (BeCu) Per UNS C36000 Per ASTM B16, Gold Plate Per MIL-G or ASTM B488 Dielectric: Virgin PTFE Fluorocarbon Per ASTM D1710 Fasteners: Per ANSI B
3 Introduction Southwest Microwave s High Performance are designed to provide Low VSWR, wideband response to 67 GHz for single-layer or multi-layer printed circuit boards where the microwave layer is on top. They are ideally suited for high frequency chip set evaluation/demo boards, test fixtures and board characterization. Features: Now available in: SMA (27 GHz), (40 GHz), (50 GHz) and 1.85 mm (67 GHz) Multiple launch configurations to optimize match to circuit Optimum performance when board launch geometry is grounded coplanar (CPWG) or top ground microstrip Unique clamping mechanism accommodates a wide range of board thicknesses (up to.110 ) while providing a continuous ground connection between end launch and circuit board. overhang that allows ground to be picked up close to the launch point Universal, robust & reusable No soldering required ship fully assembled (board not included) Examples of Applications Chip set evaluation demo boards. Board characterization. Internal board launch (not limited to perimeter board edge). Custom flanges available. 52
4 Procedure (2) # 1-72 Clamping Screws Overhang Allows Ground to be Picked Up Close to Point Step 1: Step 2: Step 3: Mount the end launch connector on the board in the desired position. Ensure the launch pin is centered on the trace. Ensure the transition block is tight against the board. Step 4: Tighten the 1-72 mounting screws until the connector is secured. Steps 5 7 (Optional) Pin Centered on Trace Via Step 5: Solder the launch pin to the trace. (Optional) (Note: Be sure the solder flows the entire length of the launch pin/trace contact area.) Step 6: Remove any excess solder. (Optional) (Note: Excess solder will affect performance.).020 Overhang Tight Against Board Step 7: Clean any flux or other residue from around (Optional) the solder joint. Circuit Trace Centered Between Mounting Holes Ground Stitching Kept Close to Ground Edge Test Boards: 1 1 Microstrip Test Board 8 mil, RO4003 Board No. B4003-8M-* GCPWG Test Board 8 mil, RO4003 Board No. B4003-8C-* Contact factory for pricing and availability. Board launch design assistance available. Contact factory. Ø.078 Thru.375 * Boards vary by maximum frequency. Contact factory for specific versions. 1 GCPWG Test Board 30 mil, RO4350 Board No. B C-* 53
5 Connector Dimensions Dimensions Field Replaceable.375 Square Flange are Available in Male or Female Configurations. Standard Profile (4) # 0-80 SHCS (2) # 1-72 SHCS Low Profile (4) # 0-80 SHCS (2) # 1-72 SHCS 54
6 Pin Diameter (27 GHz) Dim A Dim B Dim C Board Pin Internal Dielectric Dia Standard Profile A A A A A A A A-5 Pin Diameter Dielectric Dia. Standard Profile Board Pin Internal A A A A-5 (40 GHz) Dim A Dim B Dim C A A A A-5 Pin Diameter (50 GHz) Dim A Dim B Dim C Dielectric Dia. Standard Profile Board Pin Internal A A A A A A A A-5 Low Profile A A A A A A A A-6 Low Profile A A A A A A A A-6 Low Profile A A A A A A A A mm Pin Diameter (67 GHz) Dim A Dim B Dim C Dielectric Dia. Standard Profile Low Profile Board Pin Internal A A A A A A A A-6 Circuit Board Ground Plane Center Pin 55
7 Coplanar Test Data on a Coplanar Board Below are test results to 50 GHz for two A-5 end launch connectors on a.008" Rogers RO4003 coplanar board. The plot shows both VSWR and insertion loss for the test board and the two connectors. Similar boards are used for the other launch geometries. Coplanar Test Data Connector No A-5 on a Coplanar Board (Connector No A-5) S11 (VSWR) S21 (db) Frequency (GHz) is the maximum for two A-5 on a SMI Microstrip test board using.008 Rogers RO4003 coplanar board. 56
8 Microstrip Test Data on a Microstrip Board Below are test results to 67 GHz for two A-5 end launch connectors on a.008" Rogers RO4003 microstrip board with top ground launch. The plot shows both VSWR and insertion loss for the test board and the two connectors. This is not a standard test board. Connector No A-5 Microstrip Test Data on a Microstrip Board (Connector No A-5) S11 (VSWR) Frequency (GHz) is the maximum for two A-5 on a SMI microstrip test board using.008 Rogers RO4003 microstrip board S21 (db) 57
End Launch Connector Series. Introduction Specifications Model Numbers Installation Procedures... 63
End Launch Connector Series Index End Launch Connectors (to 50 GHz).... Page Introduction... 60 Specifications... 61 Model Numbers... 62 Installation Procedures... 63 Test Data (Grounded Coplanar)... 64
Southwest Microwave, Inc. Tempe, Arizona, USA +1 (480) mm (V) Series DC to 67.
The Performance Leader in Microwave Connectors 1.85 mm (V) Series DC to 67.0 GHz Connectors Supplement to Catalog Southwest Microwave, Inc. Tempe, Arizona, USA +1 (480) 78-0201 infompd@southwestmicrowave.com
Vertical Launch Connectors
Microwave Farm s Vertical Launch Connectors are specially designed for solderless vertical PCB launch on test & measurement board. These connectors have excellent electrical transition performance up to
Vertical Launch Connectors
Microwave Farm s are specially designed for solderless vertical PCB launch on test & measurement board. These connectors have excellent electrical transition performance up to 26.5 GHz, 40 GHz,50 GHz &
2.92mm (SMK) Connectors
2.92mm (SMK) Connectors Catalog belfuse.com/cinch The Johnson 2.92mm Connector provides an excellent solution for demanding applications requiring high frequency transmission. Although similar to the SMA
Series PC 3.5 precision subminiature connectors
Series PC 3.5 precision subminiature connectors Description Content HUBER+SUHNER PC 3.5 connectors are precision connectors for use in microwave applications up to 26.5 GHz. They are especially suitable
Type SMP Connectors Product Catalog
Type SMP Connectors Product Catalog Connectivity for SMP Connectors Table of Content Connectivity for Table of Contents PAGE Introduction....................................3-4 Specifications...................................5-8
Connectors. High Performance to 65 GHz. Applications. PDF Volume 1. Click Here for Table of Contents Click Here for Specifications
SMP/SMPM Applications DELTA ELECTRONICS MANUFACTURING CORP. Connectors High Performance to 65 GHz PDF Volume 1 Click Here for Table of Contents Click Here for Specifications (978) 927-1060 FAX (978) 922-6430
SMA Series. Specification. Description. Applications Civil & Military Telecommunication Instrumentation SMA SMA. Interface Mating Dimensions
Series Specification 50 ohm 0-18 GHZ connectors are adaptable to interconnection requirements of both systems and components. S-Conn offers a wide variety of cable connectors, receptacles, feed thrus,
High Performance SMA Connector Data Sheet
: PSF-S00-000 (SMA 4-Hole Panel Mount Jack) Technical Data Max. Frequency 50 Ω 26.5 GHz Min. 5 GΩ Material Surface Plating Material Data Center Contact Body BeCu Brass Insulator PTFE Captivation Low Loss
SMA SERIES COAXIAL CONNECTORS
General Information Features Part Number Index Applications Coupling types and interface mating dimensions Semi-rigid conformable cable connectors Flexible cable connectors Connectors for modules Bulkhead
MCX Connectors. Alphabetical Index. Johnson Components P.O. Box 1732 Waseca, MN Fax:
MCX Connectors Alphabetical Index 133-3701-201 3 133-3701-206 3 133-3701-211 3 133-3701-216 3 133-3701-221 3 133-3701-226 3 133-3701-231 4 133-3701-236 4 133-3701-301 5 133-3701-306 5 133-3701-311 5 133-3701-316
SMA - 50 Ohm Connectors
142-0701-621 4 142-0701-626 4 142-0701-631 4 142-0701-636 4 142-0701-701 7 142-0701-706 7 142-1701-011 5 142-1701-016 5 142-1701-031 4 142-1701-036 4 142-1701-041 5 142-1701-046 5 142-1701-121 5 142-1701-126
Test Fixture Mainframe Up to DC 40 GHz Connector Options:
Adjustable Mainframe Test Fixture Test Fixture Mainframe Up to DC 40 GHz Connector Options: APC-7, APC-3.5, Super-SMA, SMA, K, 2.4 mm Interchangeable Transitions RF-in / RF-out offset adjustable Extended
SMA Connectors. RF Coax Connectors. Product Facts
SMA Connectors Product Facts Performance to 12.4 GHz and beyond Available in various base metal options, including stainless steel, brass and zinc diecast Uses industry standard crimp tools and processes
Microwave Gilbert Push-on Interconnects
Microwave Gilbert Push-on Interconnects Table of Contents Table of Contents Connect to Precision and Performance 4 Custom Designs 5 Corning Optical Communications RF LLC 6 Reference Guide 8 GPO Products
BGA Socketing Systems
DATA BOOK BGA-TECH04 (REV. 3/04) BGA Socketing Systems Search for a footprint or build a part number online at www.bgasockets.com Solutions for Virtually Any BGA Application BGA Socket Adapter System Designed
Our Most Important Connection is with You. SECTION 3. Board-to-Board: MMBX / SMP-MAX R223 / R222M
SECTION 3 Board-to-Board: MMBX / R223 / R222M Contents MMBX Introduction... 3-4 Interface... 3-5 Characteristics... 3-6 Plugs... 3-7 PCB receptacles... 3-7 to 3-8 Adapters... 3-9 Demo board... 3-10 Panel
Prices, specifications, statement of warranty, and other terms and conditions are subject to change without notice by Lighthorse Technologies, Inc.
Section Index Connectors Specifications... 93 Flexible Cable... 95 Panel Mount... 99 Bulkhead... 100 PCB Mount... 101 In Series Adaptors... 103 Other Information Assembly Instructions... 176 Cable Assembly...
GMS Interconnect Series Product Information
GMS Interconnect Series Product Information Microwave Products Product Features: Frequency range: DC up to 23 GHz, Force to engage/disengage: 10 ounces min./2.5 pounds max., Male connectors have full self-centering
The Custom Interconnect Leader
SC Series.337.307.040.003.085.194 MIN FLARE TO MEET GAGE TEST.276 MIN.549.781 ELECTRICAL Nominal Impedance: Frequency Range: Voltage Rating: Dielectric Withstanding Voltage: Insulation Resistance: VSWR:
RF & MW Connectors RF & MW Adapters RF Connectivity. RF & MW Connectors
RF & MW Connectors - 2.4 mm Connectors - 2.92 mm(k) Connectors - Hermetic Seal (0.02 Glass Bead) - SMP Connectors - BMA Connectors - High Performance End Lanch Connectors - High Performance SMA Connectors
SMA - 50 Ohm Connectors
Alphabetical Index 142-0701-201 4 142-0701-206 4 142-0701-231 4 142-0701-235* 4 142-0701-236 4 142-0701-301 5 142-0701-306 5 142-0701-335* 6 142-0701-421 5 142-0701-426 5 142-0701-491 5 142-0701-496 5
Modular FLATPAQ. provided, and Elcon will provide samples, typically within one week.
Modular FLATPAQ Modular FLATPAQ connectors provide custom solutions to hot pluggable AC and DC power needs in a board-to-board format. By using off-the-shelf modular components, power and signal modules,
Product Specification. Mezza-pede SMT Connector Low Profile 1.0mm Pitch
Mezza-pede SMT Connector Low Profile 1.0mm Pitch Rev. 1 December 7, 2016 1.0 Scope This product specification applies to 1.0mm pitch Mezza-pede SMT Connectors, designed for the mating and unmating of a
MAXIMUM SOLUTIONS (2/14 -- PR606) Mill-Max Mfg. Corp. 190 Pine Hollow Road, Oyster Bay, NY Fax:
MAXIMUM SOLUTIONS Mill-Max Series 854 Single Row and 855 Double Row Pitch Surface Mount and Through-Hole Spring-Loaded Connectors and Mating Target Connectors Mill-Max has developed high density, (1,27
Applications & Features, Type SSMP When using blind mate connectors in an application, careful consideration has to be given to choosing the right con
SSMP Push-On Connectors & Adapters THE SSMP (Sub-Sub-Miniature-Push-On) is a 1.7 mm connector, using solid dielectric interface. The connector is 70% of the size of the SMP and therefore allows even higher
Getting Started. 1.3 X-MWsystem Vocabulary. X-MWprobe X-MWanchor X-MWjumper. X-MWblock RF. X-MWblock Bias and Control. X-MWprotoplate X-MWwall X-MWlid
1. X-Microwave System (X-MWsystem) 1.1 Overview RF and Microwave design and product development is an incredibly interesting and challenging field. The Craft is truly an art and it takes years to learn
The Custom Interconnect Leader
7-16 Series.354.276.843.811 ELECTRICAL Nominal Impedance: Frequency Range: Voltage Rating: Dielectric Withstanding Voltage: Insulation Resistance: VSWR: Intermodulation: 50 ohms DC to 7 GHz 2,700 volts
HIGH REPEATABILITY BROADBAND TO-5 RELAYS DPDT RELAY TYPE PERFORMANCE FEATURES
RF & MICROWAVE HIGH REPEATABILITY BROADBAND TO-5 RELAYS DPDT SERIES SERIES DESIGNATION RELAY TYPE Repeatable RF relay Sensitive, repeatable RF relay INTERNAL CONSTRUCTION PERFORMANCE FEATURES UPPER STATIONARY
SECTION 12 SSMA/SSMB/SSMC R121/R203/R202 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 12 SSMA/SSMB/SSMC R121/R203/R202 SIMPLIFICATION IS OUR INNOVATON Visit www.radiall.com for more information Contents SSMA Introduction... 12-4 Characteristics... 12-4 Plugs... 12-5 Receptacles...
RF Connectors Technical Data Sheet. Gold over Nickel Plated Brass Contact. Size 0.5 in [12.7 mm] . Weight lbs [2.27 g].
![RF Connectors Technical Data Sheet. Gold over Nickel Plated Brass Contact. Size 0.5 in [12.7 mm] . Weight lbs [2.27 g].](/thumbs/76/74366494.jpg "RF Connectors Technical Data Sheet. Gold over Nickel Plated Brass Contact. Size 0.5 in [12.7 mm] . Weight lbs [2.27 g].")
RP SMA Female Connector Solder Attachment for PE-SR402AL, PE-SR402FL, PE-SR402FLJ, PE- SR402TN, RG402, Gold Plated Brass Body RF Connectors Technical Data Sheet PE44723 Configuration SMA Female Reverse
Mating Interfaces 1,63 (.064) 3,45 (.135) Ø3,71 (.146) MAX Ø6,61 (.260) MAX Ø3,71 (.146) MAX
SMB / SMC Cannon's SMB Snap-on and SMC Screw-on subminiature coaxial connectors have been specifically engineered for high performance and high reliability applications in both military and commercial
SMK Connectors. General Description. Contents (Click on any line to go to the indicated page) Test Data
SMK Connectors General Description These high-performance SMK (2.92 mm) connectors feature maximum VSWR for cable connectors of 1.15:1 from DC to 18 GHz, and 1.3:1 from 18 to 40 GHz. The maximum VSWR for
Hybrid Couplers 3dB, 90º Type PC2025A2100AT00
GENERAL DESCRIPTION The PC2025A2100AT00 is a RoHS compliant low profile wideband 3dB hybrid coupler which can support mobile applications, including PCS and DCS applications. The power coupler series of
Cannon 50 Ohm Connectors
SMB / SMC Cannon's SMB Snap-on and SMC Screw-on subminiature coaxial connectors have been specifically engineered for high performance and high reliability applications in both military and commercial
PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 X3X 10X R 516 _ 1 0 _
PAGE 1/6 ISSUE 13-08-18 SERIES Micro-SPDT PART NUMBER R516 X3X 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT TECHNOLOGY
Operating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and gold plated contacts available High
Operating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and contacts available High performance insulation material General characteristics and technical
Corona 70,000 Ft. Permeability Risetime Degradation (Mated Pair) 2.0 max MH z
NDL Ultraminiature Triaxial Connectors Connector Specifications Interface Dimensions Ø.020 Ø.082 Ø.168 Ø.162 Electrical Specifications Dielectric Center contact to intermediate contact: 1000 Vrms min Withstanding
HD Series. Signal Connector DIN Applicable Markets: Mil-Aero Space Marine
Signal Connector DIN 41612 HDC and HDD interchangeable with DIN41612 C and D 0.6 mm and 1.0 mm Hypertac contacts, in a two or three row format Up to 192 positions HDT style offers mixed arrangements with
SMP. Description. Compatibility. Content. Interface dimensions (mm/inches) SMP female. Interface dimensions conformable to the following standards:
Description Compatibility HUBER+SUHNER Astrolab connectors provide a robust, proven and fully compatible plug-in solution for applications up to 40 GHz. HUBER+SUHNER Astrolab connectors have been MIL-SPEC
11525A 11524A
8 Typical Configuration 11900A 11901A 11904A 8059A 1250-1159 1250-1748 85058-60007 11900C 11901C 11901D 11904C 11904D 8059C 1250-1462 85058-60009 1190A 1250-166 1250-174 11525A 11524A 11852B 11852B Option
Elcon CROWN EDGE Card Edge-style High Current Connectors
Elcon CROWN EDGE Card Edge-style High Current Connectors CROWN EDGE is a board-to-board power interconnect solution that uses Elcon high performance Crown contact technology configured to mate directly
SECTION 1 IMP / UMP R107
1 SECTION 1 / UMP R107 Contents Introduction... 1-4 to 1-6 Characteristics...1-7 Board to board connectors...1-8 Receptacle packaging...1-9 Assembly instructions... 1-9 to 1-10 UMP Characteristics...1-11
Series SMPM-T. Description. Compatibility. Content. Interface dimensions (mm/inches) SMPM-T male (pin contact), smooth bore
Series Description The is the smallest threaded open source connector on the market. Its unique and innovative combination of a MIL- STD-348 SMPM female interface connector together with a retractable
CONNECTORS & RECEPTACLES
STRAIGHT CORD PLUG with Extended Barrel TYPE 12BL6M TYPICAL Male plug with ground key-rib. Nickel-plated diecast handle. Contact friction coupling. Flexible black strain relief. Heavy duty cable clamp.
HIGH REPEATABILITY, NORMALLY OPEN, BYPASS RF RELAYS RELAY TYPE PERFORMANCE FEATURES
RF & MICROWAVE HIGH REPEATABILITY, NORMALLY OPEN, BYPASS RF RELAYS SERIES SERIES DESIGNATION Repeatable, RF, N.O. bypass relay RELAY TYPE Sensitive, repeatable, RF, N.O. bypass relay INTERNAL CONSTRUCTION
INCHES (MILLIMETERS) CUSTOMER DRAWINGS AVAILABLE ON REQUEST
TNC Connectors Flexible Cable... 3 In-Series Adapters... 4 Specifications... 2 RF Adapter Kit Adapters... 6 N Connectors Panel Mount and In-Series Adapters... 10 Flexible Cable... 8 Specifications... 7
In-Series and Between-Series Adapters SMA
Adapters SMA In-Series and Between-Series Adapters SMA If your choice of SMA Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not
HIGH POWER HOT PLUGGABLE INTERCONNECTION SYSTEM. US Patent # 6,299,492 B1 2. POWER, RIGHT ANGLE EARLY 3. POWER, RIGHT ANGLE EARLY
HIGH POWER HOT PLUGGABLE INTERCONNECTION SYSTEM US Patent # 6,299,492 B1 The HOTMATE board to board interconnection system provides a unique method of transferring hot pluggable power requirements within
Miniature Push-Pull Series Atto Miniature Push-Pull
J Miniature Push-Pull Series Atto Miniature Push-Pull Technical Data Panel connector Cable connector Coupler connector Panel connector, cable connector and coupler connector circular housing Locking Push-Pull,
Board-to-Board connections
Board-to-Board connections MBX/MFBX/MMBX connectors Edition 2014/08 Innovative connections Your partner for system solutions The HUBER+SUHNER Group is a leading global supplier of components and systems
Ganged Board to Board SMP Solutions. Catalog. belfuse.com/cinch
Ganged Board to Board SMP Solutions Catalog belfuse.com/cinch SMP CONNECTORS One of the key benefits of the SMP connector interface is its use in high frequency blind-mate applications. The design of the
Han PCB termination. Han-Fast Lock PCB adapter for Han DD PCB adapter for Han DDD module
Han termination Contents Page Han-Fast Lock... 20.11 adapter for Han DD... 20.13 adapter for Han DDD module... 20.16 adapter for Han 40 A Axial module... 20.18 adapter for Han E... 20.20 adapter for Han
Product Performance Specification Mini Coaxial Connector
Product Performance Specification Mini Coaxial Connector 1. Scope 1.1 Content This specification covers the performance, tests and quality requirements for the Mini Coaxial connector and connector system.
BROADBAND HIGH REPEATABILITY TO-5 RELAY SPDT DC 8 GHz
BROADBAND HIGH REPEATABILITY TO-5 RELAY SPDT DC 8 GHz SERIES RF311 RF331 SERIES DESIGNATION RF311 RF331 RELAY TYPE SPDT RF TO-5 relay Sensitive, SPDT RF TO-5 relay INTERNAL CONSTRUCTION UNI-FRAME ARMATURE
APPLICATION NOTES. Connectors for LED Lighting Applications. Co-Planar Board Mating FIG. 1
APPLICATION NOTES Connectors for LED Lighting Applications Mill-Max addresses the connector needs of the growing field of LED lighting applications with products such as receptacles and sockets suitable
TXC ULTRA-MINIATURE COAXIAL CONNECTORS. Ultra-Miniature Coaxial Connectors. Features. Materials/Finish. Specifications
ULTRA-MINIATURE COAXIAL CONNECTORS TXC Ultra-Miniature Coaxial Connectors Features 1: Ultraminiaturization provided by using hermetic beads. 2: The low profile and narrow flange leads to high density mounting.
D-SUBMINIATURE PIN-IN-PASTE CONNECTORS
INPUT/OUTPUT CONNECTORS D-SUBMINIATURE PIN-IN-PASTE CONNECTORS OVERVIEW The D-Subminiature connectors are one of the most popular I/O solutions, addressing segments such as Telecommunications, Industrial,
ELECTRICAL SPECIFICATIONS** Frequency. Power Handling. Directivity. .064±.013 [1.64±0.33] Pin ±.004 [3.05±0.10] Pin 3
![ELECTRICAL SPECIFICATIONS** Frequency. Power Handling. Directivity. .064±.013 [1.64±0.33] Pin ±.004 [3.05±0.10] Pin 3](/thumbs/89/100344529.jpg "ELECTRICAL SPECIFICATIONS** Frequency. Power Handling. Directivity. .064±.013 [1.64±0.33] Pin ±.004 [3.05±0.10] Pin 3")
Pico Xinger 20dB Directional Coupler Description The 1P620 Pico Xinger is a low profile, miniature 20dB directional coupler in an easy to use surface mount package designed for MMDS and WLAN applications.
Model XDL S Rev A
Delay Line DESCRIPTION The XDL15-3-030S can be used in amplifier linearization applications from 135 2700Mhz. Small form factor of XDL15-3-030S is ideal for cascading to obtain longer delay. The Xinger
Custom Connectors Overview
Company Overview March 12, 2015 Custom Connectors Overview Tuesday, October 03, 2017 CONNECTOR OVERVIEW Engineering Manufacturing Connector Products HiLo FlexFrame Custom Connectors Standard Connectors
Standard Series Standard
Standard Series Standard Technical Data Coupler connector, cable connector and coupler connector rectangular housing Locking screw connection Protection IP 50 to IP 54 with conexil in the housing, flat-gasket
Board Mount Connector Footprint Design Process
Board Mount Connector Footprint Design Process STEP 1: Connector Selection Series Force to Engage (Max) Max SB LD FD Freq. SMP 2.0 lbs 10 lbs 15 lbs 40 GHz SMPM 3.5 lbs N/A 8.0 lbs 65 GHz SMPS 3.0 lbs
Ø 11,4 21,5. M9 x 0,5 Ø 12 Ø 11,4. M9 x 0,5 Ø 12. M9 x 0,5
Subminiature 7 series Screw termination M9 8 contacts Degree of protection IP7 Solder termination Moulded versions Diameter, mm Male angled connector 8,, Ø,, Contacts Cable outlet Ordering-No. 99 00 70
SMA. Precision 26.5GHz Connectors
SMA Precision 26.5GHz Connectors SMA Precision Connectors SMA subminiature connectors are 50 ohm precision connectors initially designed for performance through 18GHz, however the standard interface is
Directory chapter 05. D-Sub Filter subminiature D connectors, 2.54 mm pitch
F Directory chapter 05 D-Sub Filter subminiature D connectors, 2.54 mm pitch New Page General information.............................................. 05.02 Technical characteristics..........................................
8Rectangular Pin and Socket Connectors
AMPLIMITE Connectors, Subminiature Series Connectors 109 (Continued) Introduction Product Facts Military qualified connectors conform to the latest amendments of MIL-DTL-24308 Industrial versions available
OSMP Microminiature Push-On Coaxial Connectors
Introduction Features Intermateable with Gilbert GPO Series Enhanced performance features Simplified ssembly etween Series dapters For OSMP etween Series dapters, see Page 438. OSMP microminiature push-on
VITA 67 Series. Ideal For Blind Mate Applications. Electrical, Mechanical & Environmental Specifications
VITA 67 Series Delta Electronics Manufacturing Corp. introduces 4 position (VITA 67.1) and 8 position (VITA 67.2) RF connector housings designed for 3U and 6U formats within the OpenVPX architecture. Ideal
ORDERING INFORMATION: P/N 5 2 M D - x x M x HALF PITCH (1.27MM) D-SUB. IDC TYPE CABLE MALE CONNECTOR WITHOUT HOOD C0201
HALF PITCH (1.27MM) D-SUB. IDC TYPE CABLE MALE CONNECTOR WITHOUT HOOD Cover & Holder: Plastic Thermoplastic UL94V-0, P.B.T. UL94V-0, Black A B C D 20 20.20 15.80 9.30 15.00 26 24.00 19.65 9.30 15.00 36
R Actuator Terminals: 0: Solder pins 5: D-Sub connector
Terminated and non Terminated up to 40 GHz SMA - SMA2.9 - QMA - DIN 1.6 / 5.6 COAXIAL RADIALL R573 & R574 multithrow coaxial switches are offered in many configurations (over 40,000 possible possible combinations)
The con ectors serve low durability cycle applications
Power Connectors & Interconnection Systems Introduction to High Current Card Edge Connectors Product Facts Contacts on.100 [2.54] Centerlines Selective gold plating of contacts for high performance at
Universal MATE-N-LOK Headers for UMNL II Connectors
for UMNL II Connectors PC Board Vertical Pin Headers [6.5] Centerline spacing,, and 5 Circuit, In-Line Housing Nylon Flammability ating UL9V-0 Contacts Phosphor bronze Solder tail diameter.06 [1.57] elated
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF S AND MODULES FOR 40 GHz COAXIAL S AND MODULES Table of Contents SECTION 1 INSTALLATION AND REMOVAL SECTION 2 MODULE INSTALLATION AND REMOVAL SECTION 3 CROSS REFERENCE
Test Development Validation Production. Micro-BGA Socketing Systems BGA Socket Adapter Systems Flip-Top BGA Sockets BGA Interposers
Test Development Validation Production Micro-BGA Socketing Systems BGA Socket Adapter Systems Flip-Top BGA Sockets BGA Interposers BGA Socket Adapter Systems Micro-BGA Socket Adapter System 0.50mm and
Test Development Validation Production. Micro-BGA Socketing System BGA Socket Adapter System Flip-Top BGA Socket BGA Interposer
Test Development Validation Production Micro-BGA Socketing System BGA Socket Adapter System Flip-Top BGA Socket BGA Interposer BGA Socket Adapter Systems Micro-BGA Socket Adapter System 0.50mm and 0.65mm
cpci Series (2mm) Connectors
cpci Series (2mm) s Interchangeable with cpci COTS Systems Hi-Rel and Space Grade Versions Standard 2mm Footprint of cpci PICMG 2.0 Immune to Shock and Vibration LCP Insulator meets NASA Outgassing Requirements
AXOMACH E-16. High data rate links for faster data transmission. Microwave coaxial cables. Panel mount connector QUASI-FLEX. Cable mount connector 2
AXOMACH High data rate links for faster data transmission AXON proposes AXOMACH, a range of high data rate links composed of low loss microwave coaxial cables and different connector types: AXOMACH Micro-D
Labs. Introduction. Application Notes
Introduction Application Notes Florida RF has provided an extensive collection of Application Notes in this section to help designers select and specify cable assemblies. These Application Notes cover
SSMP Interconnect Series
SSMP Interconnect Series INTRODUCTION Carlisle Interconnect Technologies (CarlisleIT) designed the SSMP connector product line to further improve package density of RF/Microwave systems. The SSMP interface
D-Series High Reliability Circular Connectors
D-Series High Reliability Circular Connectors Technology Company, Inc. integramate D-Series Circular Connectors QA Technology integramate D-Series Connectors are high quality, plastic circular connectors
BMA. 1. Applications & Features, Specifications & Interface Dimensions 2. Connectors of Type BMA 3. Adapters to BMA
CONTENT BMA INTRODUCTION to CONNECTORS & ADAPTERS Page 9 7/16 Page 15 N BMA Page 45 SBX SBY Page 61 Page 85 1. Applications & Features, Specifications & Interface Dimensions 2. Connectors of Type BMA 37
Extensive range of QPL standard and custom audio connectors trusted by our fighting forces for 35 years. MIL-DTL audio connectors
Extensive range of QPL standard and custom audio connectors trusted by our fighting forces for 35 years MIL-DTL-55116 audio connectors MIL-DTL-55116 solutions Eaton s MIL--DTL--55116 connectors and cable
SERIES MCX 50 MICRO MINIATURE CONNECTORS
SERIES MCX 50 MICRO MINIATURE CONNECTORS DESCRIPTION CONTENT PAGE HUBER+SUHNER MCX micro miniature snap-on connectors offer you an excellent blend of size, weight, durability and performance for applications
Labs. Introduction. Application Notes
Introduction Application Notes Florida RF has provided an extensive collection of Application Notes in this section to help designers select and specify cable assemblies. These Application Notes cover
PC Board Sockets. Specifications SOCKETS. Surface Mount, Single Piece construction. Throughboard, Two Piece construction. Materials.
Sockets Contents SMT PCB Sockets Sockets For Ø0.5mm Pin Sockets For Ø0.8mm Pin Sockets For Ø1mm Pin Sockets For Ø2mm Pin Test Sockets IC Socket Strip Dual Row IC Socket Surface Mount, Single Piece construction
PRODUCT SPECIFICATION CUSTOM CONFIGURABLE MODULAR POWER DOCK CONNECTOR SYSTEM
1.0 SCOPE This Product Specification covers the custom configurable modular printed circuit board (PCB) Dock Connector System with gold plating. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S)
SECTION 7 SMA/SMA-COM/BMA R125/R124/R128 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 7 /COM/BMA R125/R124/R128 SIMPLIFICATION IS OUR INNOVATON Visit www.radiall.com for more information Contents BMA Introduction... 74 Characteristics... 75 Plugs... 76 Jacks... 77 to 78 Receptacles...78
09. DIN CONNECTORS
. 41 612 CONNECTORS Connectors that comply with 41 612 have been in use for years for both board-to-board applications and cable-to-board applications. Their robustness and universality are legendary.
SINGLE ROW BREAKAWAY HEADER
SINGLE ROW REKWY HEDER 3986 SERIES SERIES. 3.96mm(0.156 ). Round Pin. For PC Solder! vailable in 1through 20 circuits! Mates with 3940, 3950, 3970, 3971 and 3972 series! Insulator Material: Nylon 6/6 UL
DETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-553/3F w/amendment 8 July 7 SUPERSEDING MIL-DTL-553/3F May 6 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: PLUG, STRAIGHT-THRU, 3 thru CONTACT POSITIONS,
RAMSES SERIES R 57. SPnT Terminated & non Terminated up to 40 GHz. Our Most Important Connection is with You.
SPnT Terminated & non Terminated up to 40 GHz SMA SMA 2.9 QMA - DIN 1.6 / 5.6 Radiall's R573 & R574 multithrow coaxial switches are offered in many configurations (over 40,000 possible combinations) including
TGL2206-SM GHz 100 Watt VPIN Limiter
Applications Receive Chain Protection Commercial and Military Radar 5 mm x 5 mm QFN Package Product Features Functional Block Diagram Frequency Range: 2.0 to 5.5 GHz Insertion Loss: < 1.0 db Peak Power
CONNECTORS & RECEPTACLES
TINI Q-G MINIATURE CONNECTORS DESIGN FEATURES STYLE Streamlined, miniaturized with nickel-plated metal and contrasting black plastic parts. Designed for light weight and unobtrusiveness. Also available
ODU MAC LC. Modular Attachable Connector System
Catalogue No. 1004 LC-a ODU MAC LC Modular Attachable Connector System ODU Steckverbindungssysteme GmbH & Co. KG, Pregelstr. 11, 84453 Mühldorf a. Inn, Germany Phone: +49/ 86 31/61 56-0, Fax: +49/ 86 31/61
2.6 GHz capable, 10 W carrying power (at 2.6 GHz), 50Ω/75Ω impedance and 1 Form C relays
.6 GHz capable, W carrying power (at.6 GHz), 5Ω/75Ω impedance and Form C relays RE RELAYS (ARE)..44..44 mm inch FEATURES Excellent high frequency characteristics (to.6ghz) Surface-mount type also available
FMCK1013 DATA SHEET. Features: Applications: Configuration. Mechanical Specifications
Short Open Load Thru (SOLT) Analyzer Calibration Kit with 3.5mm Male Connections in a portable 4-in-1 Design and Operating to 26.5 GHz Short Open Load Thru (SOLT) Analyzer Calibration Kit, part number
ELECTRICAL SPECIFICATIONS**
ico Xinger 1dB Directional Coupler Description The 161 ico Xinger is a low profile, miniature 1dB directional coupler in an easy to use surface mount package designed for MMDS and WLAN applications. The
SMPM Male Thru-Hole Printed Circuit Board Mount Connector
SMPM Male Thru-Hole Printed Circuit Board Mount Connector Application Specification 114-13212 17 JAN 13 i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are