LED Driver Compact fixed output

Transcription

1 Driver LC 13W 3mA fixc C SNC ESSENCE series Product description Fixed output built-in LED Driver Constant current LED Driver Output current 3 ma output power 13 W Nominal life-time up to 5, h For luminaires of protection class I and protection class II Temperature protection as per EN C5e 5-year guarantee Properties Casing: polycarbonat, white Type of protection IP Functions Overload protection Short-circuit protection No-load protection Burst protection 1 kv Surge protection 1 kv (L to N) Surge protection 2 kv (L/N to earth) È Standards, page 3 Wiring diagrams and installation examples, page 4 1

2 Driver LC 13W 3mA fixc C SNC ESSENCE series Technical data Rated supply 2 2 V AC range V Mains frequency 5 / 6 Hz Over protection 3 V AC, 1 h Leakage current (at 23 V, 5 Hz, full load) < µa THD (at 23 V, 5 Hz, full load) < % Output current tolerance 3 ± 7.5 % Typ. current ripple (at 23 V, 5 Hz, full load) ± 3 % Turn on time (at 23 V, 5 Hz, full load).5 s Turn off time (at 23 V, 5 Hz, full load).5 s Hold on time at power failure (output) s Ambient temperature ta C Ambient temperature ta (at life-time 5, h) C Storage temperature ts C Dimensions L x W x H x x 21 mm Ordering data Type 3 D tc 37 Article number 21 4,3 31 carton low volume high volume Weight per pc. LC 13W 3mA fixc C SNC pc(s). 1, pc(s). 7, pc(s)..43 kg Specific technical data Type Output current 3 Input current (at 23 V, 5 Hz, full load) input power Typ. power consumption (at 23 V, 5 Hz, full load) Output power range Power Efficiency factor at at full full load 1 load 1 Power factor at min. load 1 Efficiency at min. load 1 Min. forward forward output output output peak current peak current at full load 2 at min. load 2 casing temperature tc LC 13W 3mA fixc C SNC 3 ma.72 A 15.5 W 15.2 W W.93C 85 %.9C 84 % 3.3 V 43.3 V 6 V 39 ma 39 ma 9 C 1 Test result at 23 V, 5 Hz. 2 The trend between min. and full load is linear. 3 Output current is mean value. 2

3 Standards EN 5515 EN EN EN EN EN EN Overload protection If the output range is exceeded the LED Driver will protect itself and LED may flicker. After elimination of the overload, the nominal operation is restored automatically. Short-circuit behaviour In case of a short circuit on the secondary side (LED) the LED Driver switches into hic-cup mode. After elimination of the short-circuit fault the LED Driver will recover automatically. No-load operation The LED Driver works in burst working mode to provide a constant output regulation which allows the application to be able to work safely when LED string opens due to a failure. Installation instructions The LED module and all contact points within the wiring must be sufficiently insulated against 3 kv surge. Air and creepage distance must be maintained. Glow-wire test according to EN with increased temperature of 85 C passed. Mounting of device torque for fixing:.5 Nm/M4 Storage conditions Humidity: 5 % up to max. 85 %, not condensed (max. 56 days/year at 85 %) Storage temperature: - C up to max. + C The devices have to be within the specified temperature range (ta) before they can be operated. Replace LED module 1. Mains off 2. Remove LED module 3. Wait for seconds 4. Connect LED module again Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs. Expected life-time Type ta C 5 C 6 C LC 13W 3mA fixc C SNC tc C 9 C x Life-time 5, h 3, h x The LED Drivers are designed for a life-time stated above under reference conditions and with a failure probability of less than %. Maximum loading of automatic circuit breakers Automatic circuit breaker type C C13 C16 C B B13 B16 B Inrush current Installation Ø 1.5 mm mm mm mm mm mm mm mm 2 Imax Time LC 13W 3mA fixc C SNC A 35 µs 3

4 Harmonic distortion in the mains supply (at 23 V / 5 Hz and full load) in % THD LC 13W 3mA fixc C SNC < < 7 < 7 < 5 < 3 < 3 Wiring diagram 2 2 V 5/6 Hz L N Wiring type and cross section The wiring can be done with a cross section of mm². Strip mm of insulation from the cables to ensure perfect operation of the push-wire terminals. wire preparation: mm² PRI Driver LC... C SNC LED + LED SEC Isolation and electric strength testing of luminaires Electronic devices can be damaged by high. This has to be considered during the routine testing of the luminaires in production. According to IEC Annex Q (informative only!) or ENEC 33-Annex A, each luminaire should be submitted to an isolation test with 5 V DC for 1 second. This test should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least 2 MΩ. + LED mm Wiring guidelines All connections must be kept as short as possible to ensure good EMI behaviour. Mains leads should be kept apart from LED Driver and other leads (ideally 5 cm distance) lenght of output wires is 2 m. Secondary switching is not permitted. Incorrect wiring can demage LED modules. The wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.). Release of the wiring Press down the push button and remove the cable from front. As an alternative, IEC Annex Q describes a test of the electrical strength with 15 V AC (or x 15 V DC). To avoid damage to the electronic devices this test must not be conducted. Additional information Additional technical information at Technical Data Guarantee conditions at Services Life-time declarations are informative and represent no warranty claim. No warranty if device was opened. 4

5 Diagrams LC 13W 3mA fixc C SNC Efficiency vs load Power factor vs load 1, 95,95 Efficiency [%] 9 85 Power factor,9,85 75, Input power vs load Input current vs load Input power [W] 15 5 Input current [ma] THD vs load 15 THD 5 5