Electrical Power Supply Matrix Systems

Transcription

1

2 Electrical Power Supply Matrix Systems A.Yu. Goncharov, PhD in Technical Sciences - AEPS-GROUP President Distributed electrical power supply systems consisting of a specified set of modules may be easily arranged at a drawing s horizontal surface as a schematic image in order to analyse and optimize the system structure. Recently, however, distributed electrical power supply system consumers have appeared, whose schematic images have a strongly expressed spatial matrix structure consisting of lines and columns with electrical power supply modules located at their crossing points. Electrical power supply systems for active phased array radars and those for supercomputers are typical examples of these rapidly developing structures. The author is the first to suggest using the term "distributed electrical power supply matrix systems" (DEPSMS) to identify such systems. Our companies, united under the brand of AEPS-GROUP, deal exactly with such electrical power supply systems. The APAR DEPSMS key element is transmitting-receiving module (TRM) which determines as much as 90% of the APAR price, weight and performance. Nowadays, the number of aircraft APAR TRM exceeds 2,000 and reaches 10,000 or more units in ground equipment. A typical modern TRM consists of UHF components (transmitter, receiver, phase shifter) and a controlling / signal conditioning microprocessor. An LF component ergonomically located in the TRM is also included. This is the bank of energy storage capacitors providing intermittent energization for the UHF transmitter (pulsed power supply modes - hundreds of nanoseconds to milliseconds duration, tens to 4-5 duty ratio). It is extremely important to miniaturize the TRM as its width and height (the average length being 150 to 250 mm) together with the liquid and air cooling components (denoting the conventional side of the square formed with the TRM width and height as L) may not exceed the emitted APAR half-wave length. i.e. L. Table 1 shows the typical values of L accounting for the actual sizes of the cooling element for different APAR frequency ranges. Table 1 Range symbol Emission frequency, GHz Wave length, mm L, mm S C X Nowadays, we have learned to accommodate UHF microcircuits in a 9-11 mm wide strip. Taking into account the necessity of a metal case to screen TRM UHF radiation from the adjacent TRMs (the EMC

3 problem) with walls at least 0.5 mm thick (the heat removal problem), it can be affirmed that the UHF portion of the TRM with L = mm will be implemented soon. One of the obstacles on the way towards miniaturization of the TRM (i. e. weight and APAA price reduction and EMC improvement) is the extremely difficult miniaturization of the electrical power supply modules and their energy storage capacitors. Reducing the dimensions of transformers and throttles for electrical power supply modules operating at frequency ranges 10,000 times less than those of the UHF portion, is an extremely difficult task. For example, the best AEPS-GROUP DC/DC and AC/DC type modules for APAR have a L exceeding 21.5 mm and 47 mm (Figs. 1, 2, 3, 4). This means that, as yet, it is impossible to create a completely decentralized (which is desirable from the overall APAR reliability point of view) C and X range DEPSMS using AEPS-GROUP modules time and expensive research are required. Fig. 1. DC/DC module JETD25, a module prototype accommodated in the TRM, width L=21.5 mm, dimensions=23x33x10 mm. Fig. 2. DC/DC module JETD50, a module prototype accommodated in the TRM, width L=21.5 mm, dimensions=23x51x10 mm.

4 Fig. 3. AC/DC module JETA60, a module prototype with PFC for APAR TRM, width L=47 mm, dimensions=101x51x18 mm. Fig. 4. AC/DC / DC/DC module TESAV50 with two alternative input voltage circuits without/with PFC (option), dimensions w/o external capacitor = 83x53x13 mm. That is why only 4 to 6 GHz max. frequency decentralized APAR DEPSMSs based on single-channel TRMs are currently feasible. Nowadays, proven technical solutions able to bypass the prohibition for APAR dimensions exceeding the emitted half-wave length can be used for APAA operating frequencies above 6 GHz. These are multichannel TRMs. Their 2-channel or 4-channel TRM common case accommodates 2 electrical power supply modules connected in series or in parallel providing for elementary (with all the following consequences) electrical power supply module back-up. In this case we obtain a decentralized DEPSMS with a very close to 1 reliability coefficient, but we face a complicated TRM and worse EMC. Manufacturing large quantities of complicated and expensive multichannel type modules instead of single-type simple TRMs adapted for robotic production, is hardly a promising business.

5 The cons also include the forced necessity of using AC/DC type centralized electrical power supply sources for these systems, e.g., inverter-based with backed-up JETA2000 PFC (Fig. 5). The result is a twostaged inversion structure with low duty ratio efficiency. Fig. 5. AC/DC module with JETA2000 PFC, dimensions=250x140x38 mm. Data published in American magazines is an excellent example of how difficulties of miniaturizing DEPSMSs consisting of more than 2,000 TRMs hamper 3D APAR implementation on the F22 RAPTOR fighter (Fig. 6). Fig. 6. Picture of APAR within the F22 fighter With all SLAR volume/weight = 565 dm 3 /553 kg and APAR DEPSMS power = 16,530 W, the DEPSMS volume/weight is 40%/45% of the total volume/weight. It should be noted here that a virtually centralized DEPSMS is used in this example. It possesses critically low reliability and has a high share in the weight of the TRM feeder-type electrical power supply system, but it is lighter than the decentralized system. The following are examples of some typical ground and airborne APAR DEPSMS implementation, and how the transistor technology used for the TRM UHF part, impacts the decentralized DEPSMS energy key indices. Design 1 (Fig. 7) was developed on the basis of GaAs UHF transistors with their typical 10 V power voltage and 0.2 efficiency. An energy storage capacitor of 3.14 nominal units volume is available (differential power voltage and efficiency are considered when comparing Designs 1 and 2).

6 Design 2 (Fig. 8) was developed on the basis of transistors with 28 V power voltage and 0.5 efficiency typical for GaN technology. An energy storage capacitor of 1 nominal unit volume is available. The following parameters are common for both designs: radiated pulse power of each TRM = 10 W, the max. frequency = 6 GHz, electrical power supply module efficiency = 0.88, TRM number = 2,000, pulse duty ratio = 5. Fig. 7. DEPSMS for APAR (GaAs). Fig. 8. DEPSMS for APAA (GaN). GaAs-based DEPSMS total volume is 10,280 nominal units or approximately 56 dm 3, and together with the centralized backed-up inverter including 18 JETA2000 type modules w/ PFC connected in parallel

7 (each one of 1,200 nominal units volume) - 21, ,280 = 31,880 nominal units or approximately 174 dm 3. GaN-based DEPSMS total volume is 4,000 nominal units or approximately 21.7 dm 3, and together with 9 centralized inverter JETA2000 type modules w/ PFC connected in parallel - 10, ,000 = 14,800 nominal units or approximately 80.4 dm 3. Comparison of Design 1 (GaAs) and Design 2 (GaN) parameters: Parameters GaAs GaN Total volume of DEPSMS 10,280 units 4,000 units DEPSMS total volume 56 dm dm3 Total volume of DEPSMS with centralized backed-up inverter Total volume of DEPSMS with centralized backed-up inverter 31,880 units 14,800 units 174 dm dm3 Energy storage capacitor 3.14 nominal units (volume) 1 nominal unit (volume) Power supply voltage 10 V 28 V Transistor efficiency Average power consumption of all TRM UHF portions 20,000 W 8,000 W Average power consumption of APAR with centralized inverter 25,244 W 10,111 W Thermal power dispersion in APAR, excluding antenna 86,855 W 10,251 W

8 Conclusions: 1. The results show that using GaN technology compared with GaAs technology can allow for gaining up to 2.5 times for APAR power consumption, more than 8 times for thermal power dispersion and more than 2 times for volumes and weights of all components. 2. Even today, in , the industry would be able to manufacture APARs based on singlechannel GaN TRM operating in S, C and partially in X ranges, with 20,000 W total output UHFpower. 3. JETD25, JETD50, JETA2000 modules produced in series by AEPS-GROUP, could be used as prototypes of electrical power supply modules for APAR and supercomputers. 4. AEPS-GROUP TESAV50 modules without/with PFC and JETA60 modules with PFC are rather promising for supercomputers and compact APAR systems direct operation from 220 V or 3х380 V generators without a centralized inverter becomes possible, dramatically improving dimensional and weight parameters and considerably reducing thermal power dispersion. The author will be grateful for questions and remarks on this material. Communication is via All the data of this article has been taken from open Internet sources.

9 New products from AEPS-GROUP 9 kw AC/DC Electrical Power Supply Unit for use with diesel generators Input voltage: VAC 3-phase Output power: up to 9,000 W Output current: up to 316 A Parallel operation function Current overload, short circuit, output overvoltage, thermal protection Remote start/shutdown Output voltage adjustment Built-in aluminium heatsink Built-in cooling fans Built-in outlet isolation diodes

10 3.6 kw AC/DC Electrical Power Supply Unit Input voltage: V Output power: up to 3,600 W Output current: up to A Parallel operation function Power factor correction. Current overload, short circuit, output overvoltage, thermal protection Remote shutdown Output voltage adjustment by means of external voltage control Possibility of operation from an accu battery in float mode Built-in aluminium heatsink Built-in cooling fans Built-in outlet isolation diodes

11 EVA JETA Demonstration Devices The EVA-JETA device is a demonstration set consisting of JETA series electrical power supply modules connected in parallel and designated for developing, under your specific conditions, technical solutions for creating powerful electrical power supply systems based on air cooled AC/DC inverters connected in parallel (with fan cooling as an option). The EVA-JETA is equipped with the relevant cooling system, indication, monitoring and alarm devices, it enables the development of both 2+1 backed-up electrical power supply systems (with the possibility of hot swapping one of its modules) and power boost systems consisting of several modules connected in parallel. The EVA-JETA demonstration set is a completely finished product and it can be used not only for developing parallel module connection, but also as a separate electrical power supply system for your projects. The set is overheat, overload and short-circuit protected.