Work Instruction IP Card Reader - Upgrade. IP Card Reader Upgrade. Product Version: Rev. 3. Version of this manual: 2.0.3

Transcription

1 IP Card Reader Upgrade Work Instruction IP Card Reader Upgrade Product Version: Rev. 3 Version of this manual: Inepro B.V. All rights reserved

2

3 IP Card Reader Upgrade The most versatile card reader solution Congratulations on your selection of Inepro card readers. We are certain you will be pleased with your purchase of one of the flexibele solutions of the market. We want to help you get the best result from your Inepro Back Office Suite. This manual contains information on how to do that; please read it carefully. Due to continuous product improvements this manual is subject to changes without notice. We strongly recommend you read the license agreement to fully understand its coverage and your responsibilities of ownership. Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your questions and your concerns. Best wishes, Inepro BV.

4 IP Card Reader Upgrade All rights reserved. No parts of this work may be reproduced in any form or by any means graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems without the written permission of the publisher. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document. Version created: July 2016 in NieuwVennep. Publisher Inepro B.V. Managing Editor K. de Graaf Technical Editors P. Blom P. Grimmerink Cover Design H. Wagenaar K. de Graaf Team Coordinator R. Groen Production Inepro B.V.

5 Table of Contents Introduction Package Content Software Installation Hardware Installation Programming Instructions Troubleshooting

6

7 Directives ATTENTION!! Read this manual carefully before installing the Card Reader! Mains connection Before connecting the appliance to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate of the adapter. If the mains voltage is different, consult your supplier. Guarentee No guarantee can be given if safety regulations are not followed. Changes and/or mdodifications Changes and/or modfications whch have not been approved by the responsible party can void the user's authorty to operate the equitement. Security Always disconnect the power supply before handling anything inside the device. Indoor User Only This device may only be used indoors. FCC Federal Communications Commission US This device is complies with part 15 of the FCC rules, operation is subject to two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, includng interference that may cause undesired operation. CE Conformité Europeène (Conform European Norm) This device is in conformity with the EMC directive and lowvoltage directive. Conformité d Industrie Canada Appareil concernés: MCR708, MCR708G, DCR708, DCR708G Confirm Canada Industries Relevant Devices: MCR708, MCR708G, DCR708, DCR708G Le présent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes : (1) l appareil ne doit pas produire de brouillage, et (2) l utilisateur de l appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. This device complies with Industry Canada s licenceexempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. End of life directives Inepro is paying a lot of attention to environmentallyfriendly production. Your new device contain materials which can be recycled and reused. At the end of its life specialised companies can dismantle the discarded device to recycle the reusable materials and to minimise the amount of materials to be disposed of. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Version I

8

9 Introduction I Part

10 Introduction This short manual will guide you trough the upgrade process of the Inepro IP Card Reader. Please follow the instructions closely. 2 IP Card Reader Upgrade

11 Package Content II Part

12 Package Content Inepro IP Card Reader Interface Package 1. Flat cable for communication between the programmer and interface board 2. USB cable for connection with the PC 3. Melabs U2 Instruction Sheet 4. Melabs U2 Setup CD 5. Melabs U2 Programmer Unit 4 IP Card Reader Upgrade

13 Software Installation III Part

14 Software Installation 1. First setup the Melabs programmer software application. 2. Please insert the installation CD. 3. Choose 'Execute Setup.exe' 6 4. Click 'Next' 5. Choose 'I accept the agreement' 6. Click 'Next' 7. Click 'Next' 8. Click 'Install' IP Card Reader Upgrade

15 Software Installation 9. Wait for the installation to finish 10. Click 'Next', ticking the boxes is optional 11. Read the information, and click 'Next' 12. Finish the installation Version

16

17 Hardware Installation IV Part

18 Hardware Installation 1. Screw the Inepro IP Card Reader box open and take out the Interface connector board. 10 IP Card Reader Upgrade

19 Hardware Installation 2) Connect the USB cable to the PC you installed the software on and the programmer unit. 3) Connect the black connector of the flat cable to the programmer unit in such a way that the red side of the cable is on the left side (this is the same side as pin 1 on the diagram on the programmer). The cable will be running away from the programmer unit. Make sure you fit the cable correctly as it can fit in more then one way! Failing to do so may result in a defective programmer unit or a defective Interface board! Repairing the resulting problems will not be covered by the guarantee! Connect the other end with the red side of the cable to the closest short edge of the connector board, the connector should only fit in one way, with the plastic rims gliding along the socket. Version

20 4) To supply power use one of the following options: a) Connect the power adaptor to the black socket next to the network connectors. b) Connect a Power over Ethernet (PoE) network cable to the PoE connector on the board. The Power over Ethernet option requires the implementation of Power over Ethernet in your network, otherwise no power can be supplied. The power adapter was supplied together with the Inepro IP Card Reader. 12 IP Card Reader Upgrade

21 Programming Instructions V Part

22 Programming Instructions To program the Inepro IP Card Reader, you need a hexfile. This file should be supplied by Inepro and is customized to meet your requirements. 1. Start the meprog.exe executable. 2. Choose 'File' > 'Open'. 3. Open the hexfile that Inepro supplied. The selected hex filename will be shown in the title bar of the application window. Double check if this name is correct. 14 IP Card Reader Upgrade

23 Programming Instructions 4. Set all the ticks in the 'Options', 'More Options' and 'Program' submenu's as shown in the image above. Version

24 5. Tick all the options in the 'Verify' menu, as shown in the image above. 16 IP Card Reader Upgrade

25 Programming Instructions 6. Tick all the options in the 'Blank Check' menu, as shown in the image above. Version

26 7. Tick all the options in the 'Erase' menu, as shown in the image above. 18 IP Card Reader Upgrade

27 Programming Instructions 8. Choose 'Program' > 'Determine Target Device' to connect the device to the application. Make sure that you remove the card reader from the 9. interface board, to prevent errors! 10. Choose 'Program' > 'Program' Version

28 11. The board will now be programmed. When the interface board is busy programming, all the LED's will be off, when it has power and it has been programmed the appropriate LED's will blink. 12.The Interface board has now been programmed and is ready for use. If you disconnected a reader at step 9, you may now reconnect it again. 20 IP Card Reader Upgrade

29 Troubleshooting VI Part

30 Troubleshooting Q A 1) Something is detected but it is not the correct device a) Check the power supply. b) Choose 'Program' > 'Determine Target Device' to attach the connected device to the software. For more information see page 19 c) Try to execute the program procedure on page 14 2) The board is empty or defect. a) Replace the interface board. Q A 1) There is no programmer detected a) Check the cables. 22 IP Card Reader Upgrade

31 Troubleshooting <This page is intentionally left blank> Version

32