AS-i Safety Output Module, IP20
|
|
|
- Alice Melissa Evans
- 6 years ago
- Views:
Transcription
1 a AS-i Safety Output Module Safe outputs and standard inputs in one module Protection category IP20 Figure Housing Inputs digital Outputs Safety, SIL3, cat.4 Input voltage (sensor supply) 1 Output voltage (actuator supply) 2 AS-i connection 3 AS-i address 4 Article no. 6x COMBICON 1- circuits, x fast electronic safe outputs out of AUX out of AUX clamps depending on number of circuits BWU236 1 Input voltage (sensor supply): inputs are supplied by AS-i or by AUX (auxiliary 24 V power). If supplied by AS-i, inputs shall not be connected to earth or to external potential. 2 Output voltage (actuator supply): outputs are supplied by AS-i or by AUX (auxiliary 24 V power). If supplied by AS-i, outputs shall not be connected to earth or to external potential. 3 AS-i connection: the connection to AS-i as well to AUX (auxiliary 24 V power) is made via yellow resp. black AS-i profile cable with piercing technology or via M12 socket (in IP20 via clamps). 4 AS-i Address: AB Slave (max. 62 AB Slaves/AS-i network), 2 AB Slaves (max. 31 modules with 2 AB Slaves), Single Slaves (max. 31 Single Slaves/AS-i network), mixed use allowed (upon request, slaves are available with specific AS- Slave profiles). We reserve the right to change any data Mannheim, page 1
2 Article no. BWU236 Connection Connection COMBICON plug Length of connector cable unlimited 1 AS-i Profile 1 loop resistance 150 Ω configuration slave: S-7.A.5 4I/4O slaves: S-7.A.7 diagnostics slaves: S-7.A.E depending on configuration Addresses Required Master profile M4 Since AS-i specification 3.0 Operating voltage 1 31,6 V Max. current consumption 200 ma AUX Voltage V (PELV) Max. current consumption A Inputs Number digital inputs Power supply out of AUX Input level U<5 V (low) U>15 V (high) Outputs Number circuits 1- circuits, configurable Number x fast electronic safe outputs Power supply out of AUX Max. output current 2 A per output, = max. A (see table Derating for output current ) Test pulse if output is switched on: minimum distance between two test pulses: 250 ms, pulse length 1 ms Display LED ASI (green) AS-i power LED FAULT/FLT (red) AS-i error LEDs I1 In (yellow) state of inputs I1 I4 LEDs SO1 SOn (yellow) state of safe outputs SO1 SO LED ALARM PLC reports alarm LED AUX (red) on: 24 V DC AUX on off: no 24 V DC AUX Environment Applied standards EN :2013 EN 6150:2010 EN 62061:2005/A1:2013 EN ISO :200/AC:2009 Operating altitude max m Ambient temperature 0 C +55 C Storage temperature -25 C +5 C Housing plastic, din-rail mounting Tolerable loading referring to humidity according to EN Protection category EN IP20 Voltage of insulation 500 V Weight 270 g Dimensions (W / H / D) in mm 22,5 / 99 / 114 page 2 Mannheim, We reserve the right to change any data
3 Derating for output current Installation with mounting distance 3 cm left/right I max. [A] 6 >50 mm >30 mm >30 mm T amb [ C] Installation without mounting distance I max. [A] >50 mm Diagnostic slave 1- (depending on number of circuits) setting of in- and outputs AS-i output AS-i input O0 P1=1 P1=0 I0 Diagnostic not used 1: output controlled by safety 0: inhibits output on irrespective of safety (see table ( Diagnostic (device colors") ) O1 not used I1 O2 not used I2 O3 inexistent I3 P2=0 P2=1 1: feedback for user: safety on 0: feedback for user: safety off In 1 Peripheral fault indicates unavailable AUX or overload on the outputs 1 state of the assigned input. T amb [ C] Release conditions Standard I/O slaves Standard I/O slaves Slave 1 Slave 2 P0 = 0 D n-1 =0 P0 = 1 D n-1 =1 P0 = 0 D n-1 =0 P0 = 1 D n-1 =1 Diagnostic slaves Slave 1 4s P1 = 1 P1 = 0 O0 = 0 O0 = 1 off off off off off Slave 5 s P1 = 1 P1 = 0 O0 = 0 O0 = 1 off off off off off We reserve the right to change any data Mannheim, page 3
4 Diagnostic (device colors) Value Color Description State change LED SO1 SO 0 green output on on 1 green flashing 2 yellow restart inhibit auxiliary signal 2 1 Hz 3 yellow flashing 4 red output off off 5 red flashing waiting for "reset of error condition" auxiliary signal 1 Hz 6 gray internal error, such as "fatal error" only via "Power On" on device all LEDs flashing 7 green/yellow output d, but not switched on switching-on by setting of O0 off Programming instructions diagnostic slave (bit setting) P1 P1=1 safety output controlled by safety only P1=0 safety output controlled by safety and O0=1 P2 P2=1 input In 1 at AS-i bit I3 P2=0 feedback for user: on s P0, P3: not used 1 state of the assigned input. 4I/4O slave Programming 4I/4O slaves (bit setting) AS-i output AS-i output Slave 1 Slave 2 Slave 1 Slave 2 O0 SO1 SO5 I0 I1 I5 O1 SO2 SO6 I1 I2 I6 O2 SO3 SO7 I2 I3 I7 O3 SO4 SO I3 I4 I Programming instructions 4I/4O slave (bit setting) P0 P0=1 safety output controlled by safety and output bit = 1 P0=0 safety output controlled by safety only s P1, P2,P3: not used Configuration slave Programming hints AS-i output AS-i input O0, communication CTT2 I0, not used O1 I1 O2, LED ALARM I2, communication CTT2 O3 not used I3 Peripheral fault indicates unavailable AUX. page 4 Mannheim, We reserve the right to change any data
5 BWU236 Clamps Description I1 In digital inputs SO1 SOn safe outputs AS-i+, AS-i- connection to the AS-i bus AUX+ ext.in supply voltage out of external 24 V, positive pole AUX- ext.in supply voltage of external 24 V, negative pole ASI ALARM Diagnostics (device colors) Value Color Description State change LED SOn 0 green output on on 1 green flashing 2 yellow restart inhibit auxiliary signal 2 1 Hz 3 yellow flashing 4 red output off off 5 red flashing waiting for "reset of error condition" or AUX missing auxiliary signal 1 or connect AUX Hz 6 gray internal error, such as "fatal error" only via "Power ON" on device all LEDs flashing 7 green/yellow output d, but not switched on switching-on by setting of O0 off Block diagram F-Logik (F-Logic) Freigabe (Release) Freigabe (Release) Eingänge (Inputs) I 1 In Ausgang (Output) SO1 Ausgang (Output) SOn AS-i + AS-i - AS-i As long as the F-logic has - by means of the safe AS-i output slaves- d, the physical outputs can be switched via the data bits of the 4I/4O slaves via standard control. If the is omitted, the physical outputs will be switched off safely. All physical outputs can be d jointly by a safe AS-i output slave. However, it is also possible to install one safe AS-i output slave for each single physical output. Each intermediate setting is possible, e.g. one safe AS-i output slave for 2 physical outputs. We reserve the right to change any data Mannheim, page 5
AS-i Safety Output Module with Diagnostic Slave, 1 EDM input, 3I and 2O
ext. in ext. in Safety Output Module with Safety and standard I/O in one module Electronic safety output Additional 3 standard inputs, 1 EDM input, 2 outputs IEC 61508 SIL 3, EN ISO 13849-1 PLe Cat 4,
Digital Modules AS-i in IP20, 22,5 mm
Digital Modules AS-i in 22,5 mm Cost efficient solution in IP20 (Figure similar) Figure Type Housing s digital digital voltage (sensor supply) (1) Output voltage (actuator supply) (2) AS-i connection (3)
AS-i Safety Relay Output Module with Diagnostic Slave, 1 EDM, 1 x 2 channel Safe Input
ext. in ext. in AS-i Safety Relay Output Module with Safety + standard I/O in one module Safety relay output with galvanically isolated contact sets, approved up to 230 V Additionally 1 EDM input, 1 x
AS-i Safety Relay Output Module with Diagnostic Slave and 1 EDM Input
Safety + standard I/O in one module Safety relay output with galvanically isolated contact sets, approved up to 230 V IEC 61508 SIL 3, EN ISO 13849-1/PLe Kat 4, EN 62061 SIL 3 Protection category IP20
Article no. BWU2045: AS-i Safety Relay Output Module with Diagnostic Slave and 1 EDM Input 1.23 NC
Safety + standard I/O in one module AS-i Safety relay output with galvanically isolated contact sets, approved up to 230 V IEC 61508 SIL 3, EN ISO 13849-1/PLe Kat 4, EN 62061 SIL 3 Protection category
Analog Modules AS-i, IP67, M12
Analog Modules, M12 2 x 2 connectors for compact housing, IP67 (Figure similar) Figure Type Inputs analog Outputs analog M12 connection Input voltage (sensor supply) Output voltage (actuator supply) (2)
AS-i Safety Input Modules (M12), IP67
Input Modules (), IP67 Input Modules (), IP67 for opto, floating contacts or complementary switch Applications up to category 4/PLe/SIL 3 (Figure similar) Figure Type Inputs, SIL 3, cat. 4 4 x, 4 x, 4
Active Distributors AS-i Safety, Active Distributors AS-i
Active Distributors Safety, Active Distributors x connectors for Periphery connection via, M cable sockets or push in terminals (Figure similar) Figure Type Inputs Safety, SIL, Cat. x 9 mm, -channels Safety
Encoder signal/ Sensor signal. Number of monitored axes. sine/cosine, SSI, TTL (1) up to 2 independent axes. sine/cosine. up to 2 independent axes
w AS-i Speed Monitor for sine/cosine encoder for HTL encoder for SSI encoder for TTL encoder for sensors for 2 fast electronic safe outputs 128 devices Supplied out of AS-i and external 24 V (figure similar)
AS-i / IO-Link Module, IO-Link Master with 4 IO-Link Ports
/ IO-Link Module, /IO-Link Module, IO-Link Master with 4 s fourfold IO-Link Master in one housing Power supply of s (or ) (Figure similar) Figure Type Inputs digital 4 x + 4 x + 4 x Outputs digital M12
AS-i 3.0 PROFINET-Gateways with integrated Safety Monitor
AS-i 3.0 PROFI Gateways with Master, 1 PROFI Slave Up to 32 release circuits up to 6 safe output circuits on the Monitor safe relays or fast electronic safe outputs up to 32 independent AS-i outputs Multiple
AS-i / IO-Link Module, IO-Link Master with 4 IO-Link Ports
/ IO-Link Module, /IO-Link Module, IO-Link Master with 4 s fourfold IO-Link Master single in one housing Power supply of s out of AUX (or ) Figure Type Inputs digital 8x M 8x M 4 x + 4 x + Outputs digital
AS-i 3.0 Sercos Gateways with integrated Safety Monitor
AS-i 3.0 Sercos Gateways with Safety on Sercos and Safe Link in one device up to 456 Devices Safely monitoring safety drives with Safety on Sercos 2 / 1 AS-i master, Sercos slave switch integrated (figure
AS-i 3.0 PROFIBUS Gateways with integrated Safety Monitor
AS-i 3.0 Gateways 2 / 1 AS-i Master, Slave 1 AS-i Safety Monitor for 2 s Operation using a single Monitor! Monitor processes safety slaves on two s Coupling between the two networks superfluous Up to 32
AS-i 3.0 PROFIBUS Gateways with integrated Safety Monitor
AS-i 3.0 Gateways 2 AS-i Masters, 1 PROFIBUS Slave Up to 32 release circuits up to 6 CAT4, SIL 3 safe output circuits on the Monitor safe relays or fast electronic safe outputs up to 32 independent AS-i
Active Distributors ASi Safety, IP67
x connectors for profile cable Periphery connection via M8 cable sockets M cable sockets (Figure similar) Figure Type Inputs, SIL 3, Cat. 4 9 mm 9 mm 9 mm 9 mm channels channels channels channels Inputs
AS-i Safety Analog Input Module, IP20
2 safe inputs in one module: 4... 20 ma or 0... 10 V or Pt100 or thermocouple (type J / K / N / R / S) Applications up to category 4/PLe/SIL 3 (figure similar) The AS-i Safety Input Module for analog inputs
AS-i 3.0 motor module
3.0 motor module 3.0 motor module for two 4 V motorized rollers Itoh Denki (PM00ME/XE/XP, PM60ME/XE/XP) with 4 binary and analog outputs Mixed input/output slave Speed setting of parameter Protection category
Digital Modules AS-i, IP67, M12
Digital Modules, IP67, M1 x connectors for color LEDs per output, state (yellow), overload (red) BWU487 / BWU547 / BWU55 / BWU594 / BWU60 / BWU713 / BWU75 / BWU78 (Figure similar) BWU617 / BWU619 / BWU66
AS-i 3.0 EtherNet/IP + Modbus TCP-Gateways with integrated Safety Monitor
AS-i 3.0 -Gateways 2 / 1 AS-i Master, -Slave (1) switch integrated Up to 64 release circuits up to circuits SIL 3, cat. 4 on the Monitor, relays or fast Safe AS-i outputs are supported up to 32 independent
AS-i 3.0 Gateways, PROFIsafe via PROFIBUS or PROFINET
safe via BUS or NET AS-i 3.0 Gateways, safe via NET or BUS safe and Safe Link in one device up to 450 devices 2 / 1 Master, NET / BUS Slave AS-i Safety input slaves report via safe AS-i Safety output slaves
AS-i 3.0 Gateways, PROFIsafe via PROFIBUS or PROFINET
safe via BUS or NET AS-i 3.0 Gateways, safe via NET or BUS safe and Safe Link in one device up to 450 devices 2 / 1 Master, NET / BUS Slave AS-i Safety input slaves report via safe AS-i Safety output slaves
AS-i 3.0 Gateways, PROFIsafe via PROFIBUS or PROFINET
safe via BUS or NET AS-i 3.0 Gateways, safe via NET or BUS 2 / 1 Master, NET / BUS Slave AS-i Safety input slaves report via safe AS-i Safety output slaves switch via safe Up to 32 release circuits up
AS-i 3.0 EtherNet/IP + Modbus TCP-Gateways with integrated Safety Monitor
AS-i 3.0 -Gateways 2 / 1 AS-i Master, -Slave 1 switch integrated up to 32 release circuits up to 6 release circuits SIL 3, cat. 4 on the Monitor Safe AS-i outputs are supported up to 32 independent AS-i
Analog Modules AS-i IP65, M12
Plug and Play as simply as digital AS-i I/O BWU1361 / BWU1362 / BWU1722 / BWU1853 / BWU1917 / BWU1363 / BWU2532 / BWU1359 / BW1360 / BWU1893 BWU1894 BWU1895 BWU1963 BWU1964 Housing, construction: IP65,
AS-i 3.0 PROFIBUS Gateways with integrated Safety Monitor
AS-i 3.0 Gateways AS-i 3.0 Gateways 2 / 1 AS-i Master, Slave 1 AS-i Safety Monitor for 2 AS-i networks Operation using a single Monitor configuration! Monitor processes safety slaves on two AS-i networks
AS-i 3.0 Motor modules
AS-i 3.0 motor modules for two 4 V motorized rollers e.g. Interroll (EC00, EC300, EC310) or RULMECA (RDR BL-) or Itoh Denki (PM00ME/XE/XP, PM60ME/XE/XP) slaves in one module 1 Single Slave with - s - digital
AS-i 3.0 motor modules
AS-i 3.0 4I/4O modules for two 4 V motorized rollers e.g. Interroll (EC00, EC300 or EC30) or RULMECA (RDR BL-) or Rollex (type 840) with binary and analog outputs Mixed input/output slave Speed setting
AS-i 3.0 Gateways, PROFIsafe via PROFIBUS or PROFINET
via PROFI or PROF AS-i 3.0 Gateways, via PROF or PROFI 22 / 1 Master, PROF / PROFI Slave AS-i Safety input slaves report via AS-i Safety output slaves switch via Up to 32 release circuits up to 6 CAT4,
AS-i 3.0 PROFIBUS Gateways with integrated Safety Monitor
AS-i 3.0 Gateways AS-i 3.0 Gateways 2 / 1 AS-i Master, Slave 1 AS-i Safety Monitor for 2 s Operation using a single Monitor! Monitor processes safety slaves on two s Coupling between the two networks superfluous
AS-i 3.0 Gateways, PROFIsafe via PROFIBUS or PROFINET
safe via or AS-i 3.0 Gateways, safe via or 2 / 1 Master, / Slave AS-i Safety input slaves report via safe AS-i Safety output slaves switch via safe Up to 32 release circuits up to 6 CAT4, SIL 3 safe output
AS-i Safety Relay Output Module with Diagnostic Slave
AS-i Safety Relay Output Module with Diagnostic Slave User Manual Revision date: 2013-01-30...supports the requirements for AS-i Safety up to SIL3 Subject to modifications without notice. Generally, this
AS-i 3.0 EtherCAT Gateways with integrated Safety Monitor
AS-i 3.0 EtherCAT Gateways with 2 / 1 Master, EtherCat Slave 1 Safety Monitor for 2 s Operation using a single Monitor! Monitor processes safety slaves on two s Coupling between the two networks superfluous
PCB AS-i modules, board based solutions
Special variants on request (Figure similar) PCB modules, board based solutions Circuit Inputs board dimensions digital Inputs analog Outputs digital Connection Coated LED status display 4 Input voltage
AS-i 3.0 PROFIBUS Gateways with integrated Safety Monitor
AS-i 3.0 Gateways AS-i 3.0 Gateways 2 / 1 Master, Slave 1 AS-i Safety Monitor for 2 AS-i networks Operation using a single Monitor configuration! Monitor processes safety slaves on two AS-i networks Coupling
AS-i Safety Relay Output Module with Diagnostic Slave
AS-i Safety Relay Output Module with Diagnostic Slave User Manual...supports the requirements for AS-i Safety up to SIL3 Revision date: 2016-03-9 Subject to modifications without notice. Generally, this
System manual AS-i safety monitor AC041S /00 05/2013
System manual AS-i safety monitor AC041S UK 7390926/00 05/2013 Contents 1 Preliminary note...4 1.1 Symbols used...4 2 Safety instructions...5 3 Items supplied...6 4 Functions and features...6 5 Structure
AS-Interface I/O Module
AS-Interface I/O Module Construction The AS-Interface I/O module is designed as a compact, robust field module. It is composed of an electronic module (top) and a coupler module (base). Connectors (standard
Operating instructions AS-i SmartLine module AC3200 AC /00 06/2016
Operating instructions AS-i SmartLine module AC3200 AC3201 80237876/00 06/2016 Contents 1 Preliminary note...3 1.1 Symbols used...3 1.2 Warnings used...3 2 Safety instructions...3 2.1 General...3 2.2 Target
XPSMF40. Main. Safety module name. Monitoring safety detection discrete input Monitoring safety dialogue discrete output
Product datasheet Characteristics XPSMF4000 Preventa safety PLC compact - Safe Ethernet Main Range of product Product or component type Safety module name Safety module application Preventa Safety automation
Operating instructions ClassicLine module AC5204 / AC5209 / AC5212 AC5235 / AC5236 / AC5237 AC /00 07/2017
Operating instructions ClassicLine module AC5204 / AC5209 / AC5212 AC5235 / AC5236 / AC5237 AC5274 7390889/00 07/2017 Contents 1 Functions and features...3 2 Operating and display elements...3 3 Installation...4
Original operating instructions Safety relay with relay outputs G1501S / / 2016
Original operating instructions Safety relay with relay outputs G50S UK 8023637 / 00 02 / 206 Contents Preliminary note...4. Symbols used...4 2 Safety instructions...5 3 Items supplied...6 4 Functions
XPSMCMDO Digital output pairs expansion modules with screw term
Characteristics 2 Digital output pairs expansion modules with screw term Main Range of product Product or component type Device short name Electrical connection [Us] rated supply voltage Number of inputs
Operating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
4 non-safe digital I/O channels 2 IO-Link Master V1.1 slots. Figure 1. Figure 2. Type designation. TBPN-L1-FDIO1-2IOL Ident-No
PROFINET slave Integrated Ethernet switch 100 Mbps supported 2 x M12, 4-pin, D-coded, Ethernet fieldbus connection Glass fiber reinforced housing Shock and vibration tested Fully potted module electronics
XPSMF35. Product data sheet Characteristics. Preventa safety PLC compact - Profibus DP protocol. Main. Complementary. Safety module name
Product data sheet Characteristics XPSMF3542 Preventa safety PLC compact - Profibus DP protocol Main Range of product Product or component type Safety module name Safety module application Nov 13, 2018
Compact Coded Magnetic Safety Interlock Switch and Control Units
C Conforms to EN292, EN60204-1, EN954-1, EN1088, EN60947-5-3, EN947-5-3, EN50081, EN50082, EN61000-6-2 UL and C-UL listed, TUV certified Description R US Compact Coded Magnetic Safety Interlock Switch
VersaPoint I/O Module
Output 24VDC Positive Logic 0.5A 14 Points Module is used to output 24VDC digital signals. Module Specifications Housing dimensions (width x height x depth) Connection style Operating temperature 48.8mm
RSTI-EP Slice I/O. Digital Output Module
GFK-2959B December 2015 RSTI-EP Slice I/O Digital Output Modules EP-2214, EP-2614, EP-2634, EP-2218, EP-225F Relay Output Module Solid-state Relay Output Module EP-2814 Module Status LED Channel Status
VersaMax IP I/O Module
Module accepts four digital input signals and provides four digital outputs. It connects to a local bus that is interfaced to a Profibus-DP / PROFINET network by a Profibus Interface Unit (IC677PBI001)
Product and functional description. Application Program. instabus EIB Technical product information. April (6 x AC 230 V / 0,05 A)
Product and functional description also functions if the bus cable is not connected or if the bus communication fails. After a long push button action (> 2 s), the other valve group is selected. The yellow
XPSMCMMX inputs 2 output pairs expansion module with screw term
Characteristics 8 inputs 2 output pairs expansion module with screw term Main Range of product Product or component type Device short name Electrical connection [Us] rated supply voltage Number of inputs
GS202 Encoder Switch
GS202 Encoder Switch 20:2 encoder switch 20 encoder inputs (TTL / RS422 standard) Input signals A, /A, B, /B, Z, /Z on each encoder input 2 x 6 control inputs (HTL / PNP) 2 encoder outputs (TTL / RS422
ABB i-bus KNX Analogue Input, 4-fold, MDRC AE/S , 2CDG110190R0011
Technical Data 2CDC504084D0201 ABB i-bus KNX Product description The device is used to record analogue data. Four conventional sensors can be connected to the device. The connection to the bus is established
4 non-safe digital I/O channels 2 IO-Link Master V1.1 slots. Figure 1. Figure 2. Type designation. TBPN-L1-FDIO1-2IOL Ident no
PROFINET slave Integrated Ethernet switch 100 Mbps supported 2 x M12, 4-pin, D-coded, Ethernet fieldbus connection Glass fiber reinforced housing Shock and vibration tested Fully potted module electronics
E-STOP relays, safety gate monitors
Safety relay for monitoring E-STOP pushbuttons, safety gates and light barriers. Approvals Block diagram Unit features Positive-guided relay outputs: 6 safety contacts (N/O), instantaneous 4 auxiliary
Original operating instructions Safety relay with relay outputs with and without delay G1502S / / 2016
Original operating instructions Safety relay with relay outputs with and without delay UK G50S 803638 / 00 0 / 06 Contents Preliminary note...4. Symbols used...4 Safety instructions...5 3 Items supplied...6
SECTION 16 LED DIAGNOSTIC FEATURES: EXPANSION UNITS: SCR-31P-i. SCR-73-i. SEU-31-i. SCR-31-42TD-i. SEU-31TD-i
SECTION 16 VIPER Safety Relays Type: SCR-i (with added diagnostics) SAFETY RELAY FUNCTION: IDEM s VIPER SCR-i range of Safety Relays have been designed in accordance with EN60204-1 for safety circuits
Installation Instructions Temperature transmitter TAA /00 06/2011
Installation Instructions Temperature transmitter TAA431 706042/00 06/2011 Contents 1 Functions and features...3 2 Installation...4 2.1 Addressing...4 2.2 Mechanical installation...4 2.3 Connection to
CM Series. Most Diverse and Flexible Line of Coded Magnetic Safety Interlock Switches and Controllers. Description. Safety Interlock Switches
R Safety Interlock Switches CM Series CM For full product information, visit www.sti.com. Use the SpeedSPEC Code for quick access to the specific web page. Most Diverse and Flexible Line of Coded Magnetic
Operating instructions ClassicLine module AC5203 / AC5205 AC5208 / AC5211 AC5213 / AC5214 AC5215 / AC5233 AC /00 02/2015
Operating instructions ClassicLine module AC5203 / AC5205 AC5208 / AC5211 AC5213 / AC5214 AC5215 / AC5233 AC5294 80226775/00 02/2015 Contents 1 Preliminary note...3 2 Safety instructions...3 3 Functions
Safety control unit B1 / B1. for 2 to 16 machine safety sensors. Use. Types. + PLd according to EN ISO
Safety control unit for 2 to 16 machine safety sensors 470 121 B1 / 470 125 B1 + PLd according to EN ISO 13849-1 + two safety outputs and external contactor monitoring + for sensors with N.O./N.C. system
PSR-PC50. SIL 3 coupling relay for safety-related switch on. Data sheet. 1 Description
SIL 3 coupling relay for safety-related switch on Data sheet 105818_en_01 PHOENIX CONTACT 2014-08-18 1 Description The PSR-PC50 SIL coupling relay can be used for power adaptation and electrical isolation
Line Coupler, MDRC LK/S 3.1, GH Q R0001
, GH Q605 0067 000 The coupler can be used as a line The coupler is installed in the distribution board on the data rail of the coupler or a backbone coupler. CDC 07 0 F000 As a line coupler, it links
Operating instructions valve control box AS-i
THIS LEAFLET SHOULD BE KEPT IN A SAFE PLACE FOR REFERENCE Operating instructions valve control box AS-i 1 System description The Norgren Herion valve control box is used for controlling pneumatic swivel
PSR-MS60. Safety relay for emergency stop, safety door and light grid monitoring. Data sheet. 1 Description
SILCL IEC 62061 Safety relay for emergency stop, safety door and light grid monitoring Data sheet 106171_en_01 PHOENIX CONTACT 2015-05-19 1 Description Intended Use The PSR-MS60 safety relay can be used
Solid State Remote Power Controller E /627
Solid State Remote Power Controller E--623/62 Description The E-T-A Solid State Remote Power Controllers E--623/62 are electronic control modules suitable for inductive loads such as electromagnetic valves
AS-i Safety. Two-wire bus system.
AS-i Safety Two-wire bus system Contents Page 1 Why should I use the bus system at component level? 3:2 AS-i Safety from ABB Jokab Safety 3:4 Pluto AS-i 3:6 Why should you use safety node Urax? 3:11 Safety
General Data. Ambient Conditions - Operating temperature: -25 C C - Storage temperature: -40 C C - Humidity: up to 95%, non-condensing
558 General Data Type Reference: Description: Approvals: ASI_BZ, ASI_BZL5 AS-Interface-Slave ASI, ccsaus, GOST-R, UkrSepro Communication - AS-Interface Specification: V2.11 - Slave profile: S-B.A.E - Connection:
E-STOP relays, safety gate monitors
Safety relay for monitoring E-STOP pushbuttons and safety gates. Approvals Unit features Positive-guided relay outputs: 5 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Connection
Communications & Networking
is a type of field bus that is primarily intended to be used to control sensors and actuators. is a network system that is compatible with the IEC62026 standard. A master device can communicate with slave
STBEHC3020KC counter kit STB - 1 CH Hz - 2 I
Characteristics counter kit STB - 1 CH - 0..40000 Hz - 2 I Main Range of product Product or component type Number of channels 1 Complementary Kit composition Counting input number 2 Counting frequency
SIMOCODE 3UF Motor Management and Control Devices
Technical specifications General data applicable to the basic units, current measuring modules, current/voltage measuring modules, expansion modules, decoupling module and operator panel Permissible ambient
Operating instructions. Speed monitor D / / 2014
Operating instructions Speed monitor D200 80005257 / 00 05 / 2014 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5 2.2 Target group...5
Operating instructions Diagnostic electronics for vibration sensors VSE002 / VXE002 / VXE003 VYE001 / VYE002 / VYE003 / VYE /01 05/2015
Operating instructions Diagnostic electronics for vibration sensors VSE00 / VXE00 / VXE00 VYE00 / VYE00 / VYE00 / VYE0 80677/0 05/05 Contents Preliminary note... Safety instructions... Functions and features...
SITOP in the SIMATIC Design
Siemens AG 2017 /2 Introduction /3 1-phase, 24 V DC (for S7-300 and ET 200M) /9 1-phase, 24 V DC (for S7-1200) /11 1-phase, 24 V DC (for S7-1500 and ET 200MP) /14 3-phase, 24 V DC (ET 200pro) Siemens KT
Original operating instructions. Fail-safe SmartPLC with Profinet slave interface AC402S /00 06/2016
Original operating instructions Fail-safe SmartPLC with Profinet slave interface AC402S UK 80237419/00 06/2016 Contents 1 Preliminary note...4 1.1 Notes on this document...4 1.2 Symbols used...4 2 Safety
Making Hazardous Operations Safe and Productive
NEW Safety Guard Switching Unit G9SX-GS Making Hazardous Operations Safe and Productive Making Hazardous Operations Safe and Productive This new addition to the model of Flexible Safety Unit G9SX series
PSR-SCP- 24DC/SDC4/2X1/B PSR-SPP- 24DC/SDC4/2X1/B
PSR-SCP- 24DC/SDC4/2X1/B PSR-SPP- 24DC/SDC4/2X1/B Safety Relay for Emergency Stop and Safety Door Circuits INTERFACE Data Sheet 102858_02_en PHOENIX CONTACT - 12/2006 Description The PSR-...- 24DC/SDC4/2X1/B
Iso DIN. User Manual. 1 channel Earth Fault Monitoring
Page 1 of 5 2017 03 20 User Manual Iso DIN Iso DIN User Manual 1 channel Earth Fault Monitoring Megacon AB Ranhammarsvägen 20 S 168 67 Bromma Sweden Tel: 08 402 42 50 sales@megacon.se www.megacon.se eee
Safety System CES-FD. Non-contact safety system CES-FD- Direct connection to decentralized peripheral systems (e.g. ET200pro) PLC
Non-contact safety system CES-FD- Evaluation of signals in the field Connection of CES read heads Connection to the ET200s and ET200pro Familiar EUCHNER AP interface Functional description Field evaluation
LXM28AU07M3X motion servo drive - Lexium 28 - single and three phase V W
Characteristics motion servo drive - Lexium 28 - single and three phase 200...230 V - 750 W Main Range of product Lexium 28 Product or component type Device short name Format of the drive Line current
PSR UC/ESAM4/3X1/1X2/B
Safety relay for emergency stop and safety door monitoring Data sheet 105318_en_02 PHOENIX CONTACT 2014-06-13 1 Description The safety relay can be used in safety circuits according to EN 60240-1 and IEC
Can be configured in the PNOZmulti Configurator Semiconductor outputs: or 4 safety outputs in accordance with EN 954-1, Cat. 3
Products Expansion Gertebild mo1p modules PNOZmulti Verwendung/Bildunterschrift_multi_Modul Expansion module for connection to a base unit from the configurable control system PNOZmulti Approvals Unit
G9SX-GS. Safety Guard Switching Unit. A Safety Measure for Hazardous Operations That Does Not Lower Productivity. Auto Switching Function
Safety Guard Switching Unit CSM DS_E_6_1 A Safety Measure for Hazardous Operations That Does Not Lower Productivity Two functions support two types of application: Auto switching: For applications where
ISO SINAMICS G110D FAQ
Cover sheet Safe Torque Off (STO) of an AS-idriven SINAMICS G110D with SIL 3 in compliance with IEC 62061 or PL e in compliance with ISO 13849-1 SINAMICS G110D FAQ November 2012 Service & Support Answers
Pluto AS-i Safety. Simplify construction of systems! Provides a flexible system! Allows easy expansion of the system!
Pluto AS-i Safety Simplify construction of systems! Provides a flexible system! Allows easy expansion of the system! Why should I use the Bus System at Component Level?... 3:2 How does the Bus System AS-interface
TXM1.8U TXM1.8U-ML. Universal modules TX-I/O
8 173 TX-I/O niversal modules TXM1.8 TXM1.8-ML Two fully compatible versions: TXM1.8: 8 inputs/outputs with LED signal / fault indication TXM1.8-ML: As TXM1.8, but with additional local override facility
ILBIB24DO16-DSUB. Inline Block IO Module for INTERBUS With 16 Digital Outputs; Bus Connection via D-SUB Connectors
Inline Block IO Module for INTERBUS With 16 Digital Outputs; Bus Connection via D-SUB Connectors AUTOMATIONWORX Data Sheet 7119_en_02 PHOENIX CONTACT - 03/2007 Description The ILB IB 24 DO16-DSUB module
Phone: Fax: Web: -
In automated systems, sensors and actuators must interact with one another functionally and safely. The necessary coordination is performed by the programmable Safety Controller. The controller monitors
The SMART Non-contact Safety Sensor SRF With an innovative diagnostic system
The SMART With an innovative diagnostic system Actual size shown Very compact: small in size, flexible in use Very Smart: suitable for Industry 4.0 with its intelligent diagnostic system Cost Saving: four-wire
Installation instructions Diagnostic electronics for vibration sensors VSE / / 2007
Installation instructions Diagnostic electronics for vibration sensors UK VSE00 70406 / 00 07 / 2007 Contents Safety instructions 3 Function and features 4 Mounting 4 Mounting of the sensors 5 Electrical
Binary output and supervision 520CSD01 Data sheet
RTU520 product line Binary output and supervision 520CSD01 Data sheet R01 C01 O01 R02 O02 RTU I/O bus ERR Microcontroller RAM Flash IOC Output register DC DC (1 out of n) check Output state monitoring
SMARTSCAN INFORMATION
SMARTSCAN INFORMATION RY4 SERIES SAFETY RELAYS HANDBOOK Smartscan Ltd, Pywell Road, CORBY, NN17 5XJ, UK, Tel: +44 (0) 1536 401313, Fax: +44 (0) 1536 268954, Email: sales@smartscan.com, www.smartscan.co.uk
VEO. V2UF230V10 Art.Nr.: TECHNICAL DATA
Continous voltage monitoring Mains fluctuation detection Detects voltage drop / short interruptions of at least 10ms Prevents undefined states in switching and control systems Generates reset pulse after
CONFIGURABLE SAFETY RELAYS
CONFIGURABLE SAFETY RELAYS The cycle control function of the configurable MSI allows efficient semi-automatic processes Special features Single or double-cycle operation with 0 s / 0 min time monitoring
Non-Contact Safety System CES-AZ
Evaluation unit CE-AZ-AE-01B/ CE-AZ-UE-01B 1) 2) 1 read head can be connected 2 safety outputs (relay contacts with 2 internally connected NO contacts per output) tart button and feedback loop can be connected
PSR DC/ESP4/2X1/1X2
PSR-...- 24DC/ESP4/2X1/1X2 Safety relay for emergency stop and safety door monitoring Data sheet 100516_en_05 PHOENIX CONTACT 2013-11-21 1 Description The safety relay can be used for emergency stop and
XPSMCMCO0000EM Modbus TCPIP diagnostic expansion module with screw term
Characteristics Modbus TCPIP diagnostic expansion module with screw term Main Range of product Product or component type Device short name [Us] rated supply voltage Complementary Power dissipation in W
02/11/2015
DIN Rail Mount 35 mm HSV Part number 84874320 Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - 3-wire PNP or NPN, Namur, voltage 0-30V or volt-free contact