PowerFlex 700S and 700H Frame 11 Replacement Power Structures

Size: px
Start display at page:

Download "PowerFlex 700S and 700H Frame 11 Replacement Power Structures"

Transcription

1 Installation Instructions PowerFlex 700S and 700H Frame 11 Replacement Power Structures Introduction Use this document to install a replacement power structure on a PowerFlex 700S or 700H frame 11 drive. This document covers the following replacement power structures: Spare Module Catalog String PowerFlex 700H AC Input PowerFlex 700H DC Input PowerFlex 700S AC Input PowerFlex 700S DC Input SK-H1-PWRMOD-E460 20CE460 20CK460 20DE460 20DK460 20CF460 20CM460 20DF460 20DM460 SK-H1-PWRMOD-E502 20CE502 20CK502 20DE502 20DK502 20CF502 20CM502 20DF502 20DM502 SK-H1-PWRMOD-E590 20CE590 20CK590 20DE590 20DK590 20CF590 20CM590 20DF590 20DM590 SK-H1-PWRMOD-D590 20CC590 20CH590 20DC590 20DH590 20CD590 20CJ590 20DD590 20DJ590 SK-H1-PWRMOD-D650 20CC650 20CH650 20DC650 20DH650 20CD650 20CJ650 20DD650 20DJ650 SK-H1-PWRMOD-D730 20CC730 20CH730 20DC730 20DH730 20CD730 20CJ730 20DD730 20DJ730 What You Need to Do Step 1: Configure new power structure Step 2: Remove power from existing drive Step 3: Remove old power structure Step 4: Install new power structure Step 5: Connect new power structure to components in drive Step 6: Install product identification label on new power structure Step 7: Start drive

2 2 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Step 1: Configuring the New Power Structure Before configuring the power structure you must remove the protective covers from the drive. Refer to publication PFLEX-IN006, Installation Instructions - PowerFlex 700S and 700H High Power Drives, for assistance in removing these covers. Configuring a DC Input Drive Power structures are shipped from the factory pre-configured for DC input operation. Connecting an AC Input Drive Power structures are shipped from the factory pre-configured for DC input operation. When installing a replacement power structure on a drive with AC input, you must remove the X2 plug from it s protective sleeve and plug the cable into the ASIC and Rectifier board(s). Task A B C D E F Description Remove the cover from the ASIC board assembly. Disconnect the ASIC fan from the assembly by unplugging the cable from on the ASIC board (see Figure 1 on page 3 for location). Remove the cover from the connector on the loose cable (bundled with the flat gate driver board cables) and connect the cable to the X2 connector on the ASIC board (see Figure 1 on page 3 for location). Connect the other end of the cable connected to X2 on the ASIC board to the 3 connector for the Rectifier board(s) on the V Phase and W Phase (if present) power stack (see Figure 2 on page 3 for location). Connect the fan cable to the connector on the ASIC board. Install the cover on the ASIC board assembly.

3 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 3 Figure 1 ASIC Board Connections X9 5 H1 H2 H3 H4 H5 H6 H7 X6 Connect cable to X2 connector X2 connector H8 H9 H10 H11 H12 H13 X3 X4 X5 Figure 2 Rectifier Board Connectors Cable connected to X2 on ASIC board 3 connectors for Rectifier boards

4 4 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Configuring the EMC Filter Frame 11 size drives are equipped with common mode capacitors. To guard against drive damage, these capacitors should be disconnected depending upon the type of ground system on which the drive is installed. Installation on an Ungrounded Distribution System or High Resistive Ground If you are installing a 400/480V AC input drive on an ungrounded distribution system or high resistive ground, you: Must move the common mode jumper to the disconnected position - refer to Move the Common Mode Jumper to the Disconnected Position on page 6. Should insulate terminal X4 on the Rectifier circuit board- refer to Insulate Terminal X4 on the Rectifier Circuit Board on page 7. If you are installing a 600/690V AC input drive on an ungrounded distribution system or high resistive ground, you: Must move the common mode jumper to the disconnected position - refer to Move the Common Mode Jumper to the Disconnected Position on page 6. Must insulate terminal X4 on the Rectifier circuit board- refer to Insulate Terminal X4 on the Rectifier Circuit Board on page 7. Installation on a Grounded B Phase Delta System If you are installing a drive on a grounded B phase Delta system, you: Must move the common mode jumper to the disconnected position - refer to Move the Common Mode Jumper to the Disconnected Position on page 6. Must insulate terminal X4 on the Rectifier circuit board- refer to Insulate Terminal X4 on the Rectifier Circuit Board on page 7. Note: Refer to Wiring and Grounding Guidelines for Pulse Width Modulated (PWM) AC Drives - Installation Instructions, publication DRIVES-IN001, for additional information on an ungrounded distribution system or high resistive ground installation.

5 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 5 The jumper is located on the Rectifying Module(s). For drives with one Rectifying Module, it is located on the upper-right side of the middle power stack (V Phase). For drives with two Rectifying Modules, they are located on the upper-right side of the middle (V Phase) and right-side (W Phase) power stacks. Voltage Class Amps Number of Rectifying Modules 400/480V AC /690V AC Figure 3 Common Mode Jumper and Rectifier Circuit Board Location Common Mode jumper There is one jumper located on each Rectifying Module. The Rectifying Modules are located on the upper-right side of the center and right side power stack of the drive s power structure. Front View of Assembly Rectifier Circuit Board

6 6 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Move the Common Mode Jumper to the Disconnected Position 1. Follow the lettered steps below to move the common mode jumper to the disconnected position (refer to Figure 3 on page 5 for jumper location). Task A B C D Description Loosen the upper screw. Remove the lower screw. Move the jumper to the horizontal position. Install and tighten the screws. A Front View of Power Structure D C B Rectifying Circuit Board

7 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 7 Insulate Terminal X4 on the Rectifier Circuit Board 1. Follow the lettered steps below to insulate terminal X4 on the Rectifier circuit board (refer to Figure 3 on page 5 for jumper location). Task A B Description Remove the screw from the X4 connection on the Rectifier circuit board. Insulate the top and bottom of the X4 connection on the Rectifier circuit board. Important: Do not install the screw and washer that was removed from this connection. A Side View of Power Structure B X4 X4 X41 X41 Rectifier Circuit Board

8 8 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Step 2: Removing Power From the Existing Drive! ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before servicing the drive. Check the DC bus voltage at the Power Terminal Block by measuring between the +DC and -DC terminals, between the +DC terminal and the chassis, and between the -DC terminal and the chassis. The voltage must be zero for all three measurements. Remove power before making or breaking cable connections. When you remove or insert a cable connector with power applied, an electrical arc may occur. An electrical arc can cause personal injury or property damage by: sending an erroneous signal to your system s field devices, causing unintended machine motion causing an explosion in a hazardous environment Electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance. 1. Turn off and lock out input power. Wait five minutes. 2. Verify that there is no voltage at the drive s input power terminals. 3. Measure between the +DC and -DC terminals, between the +DC terminal and the chassis, and between the -DC terminal and the chassis. The voltage must be zero for all three measurements. L1 L2 L3 I O Step 3: Removing the Old Power Structure Refer to the PowerFlex 700H/S Frame 11 Hardware Service Manual, publication PFLEX-TG003, for information about removing the power structure. Step 4: Installing the New Power Structure Refer to the PowerFlex 700H/S Frame 11 Hardware Service Manual, publication PFLEX-TG003, for information about installing the power structure.

9 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 9 Step 5: Connecting the Power Structure to Components in the Drive You must connect the power structure to control components on the control frame. If the drive has DC input, you must also connect the precharge circuit. Connections to the 700S Control Frame When installing a power structure in a PowerFlex 700S drive, you must make the following connections between the ASIC and Fiber Optic Interface, Power Supply Voltage Feedback, Common Mode Filter and Rectifier boards. Connect this component: termination point in the Power Structure to ASIC Board: H1 ASIC Board: H2 ASIC Board: H3 ASIC Board: H4 ASIC Board: H5 ASIC Board: H6 ASIC Board: H7 ASIC Board: 0 ASIC Board: X2 Power Supply Voltage Feedback Board: J8 Power Supply Voltage Feedback Board: J5 Power Supply Voltage Feedback Board: J4 this component : termination point on the Control Frame Fiber Optic Interface Board: J8 Fiber Optic Interface Board: J9 Fiber Optic Interface Board: J10 Fiber Optic Interface Board: J11 Fiber Optic Interface Board: J12 Fiber Optic Interface Board: J14 Fiber Optic Interface Board: J13 Insulate and do not connect Rectifier Board: 3 (AC input drives only) Common Mode Filter Board: J5 Fiber Optic Interface Board: J6 Fiber Optic Interface Board: J7 Figure 4 Connections for 700S Drives with Phase II Control Make and verify these connections To 3 Connector for Rectifier Board (AC Input Drives Only) X2 ASIC Board RJ45 Connector Embedded P2 P1 EtherNet I/P Option Board H1 (Gate Enable) H2 (U Gate) H3 (V Gate) H4 (W Gate) TX RX P1 SynchLink Option Board RS232 H5 (ADconv) H6 (Vbus Tx) H7 (Vbus Rx) Comm Input P1 NetLinx Daughtercard CompactFlash Memory Compact I/O 80 Feedback Inputs P2 P2 P3 P1 Logix Expansion Board Feedback Option Board P1 P2 P3 Second Encoder or P3 Safe Off Option Board 700S Control Assembly (Phase II) P3 P10 P11 P12 P13 Main Control Board P4 TB1 P7 P5 TB2 P9 P2 P1 P6 P J1 J2 J3 J17 DriveLogix Battery M6 Control Pan Fan J8 J9 J10 J11 J12 J14 J V Iso +12 V -12 V +5V Fiber Optic Interface Board J18 M 2 J15 2 External 24V DC 1 = 24V 3 = Common (75W min) Fiber Optic Cables Common Mode Filter Board J5 2 J1 J5 8 J6 Tx J7 Rx 9 J4 J16 2 Fiber 9 2 X2 X4 9 8 X3 0 Inside Power Structure J8 +24V J5 Rx J4 Tx 20-VB00601 DPI Interface Board 20 DPI Comm Option 80W Power Supply Power Supply Voltage Feedback J2 PWR STS PORT MOD NET A NET B DPI Assembly J3 J2 DC- DC+ J1 -U -V -W DPI Bezel J1 HIM DOOR EXAMPLE: 20-HIM-A3 HIM EXTERNAL DPI

10 10 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Figure 5 Termination Points on the ASIC Board Fiber Optic connections to the Fiber Optic Interface board Connect to Pre-charge circuitry on DC input drives X9 5 H1 H2 H3 H4 H5 H6 H7 X6 X2 Connects to 3 connector for the Rectifier boards on the center and right side power stacks on AC input drives Connects to fan on ASIC assembly cover H8 H9 H10 H11 H12 H13 X3 X4 X5

11 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 11 Fiber Optic Interface Board Figure 6 Termination Points on 700S Boards Power Supply Voltage Feedback Board J4 J5 J8 J9 J10 J8 J11 J12 J14 J13 J6 J7 Common Mode Filter Board J1 J5 J5

12 12 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Connections to the 700H Control Frame When installing a power structure in a PowerFlex 700H drive, you must make eight connections between the ASIC and Fiber Optic Adapter and Rectifier boards. Connect this component: termination point in the Power Structure to ASIC Board: H1 ASIC Board: H2 ASIC Board: H3 ASIC Board: H4 ASIC Board: H5 ASIC Board: H6 ASIC Board: H7 ASIC Board: 0 ASIC Board: X2 this component : termination point on the Control Frame Fiber Optic Adapter Board: H1 Fiber Optic Adapter Board: H2 Fiber Optic Adapter Board: H3 Fiber Optic Adapter Board: H4 Fiber Optic Adapter Board: H5 Fiber Optic Adapter Board: H6 Fiber Optic Adapter Board: H7 Fiber Optic Adapter Board: X2 Rectifier Board: 3 Figure 7 Connections Between the Power Structure and Control Frame (700H Drives) Make and verify these connections 0 H1 H2 H3 H4 ASIC Board To 3 Connector for Rectifier Board (AC Input Drives Only) H5 H6 H7 X2 Fiber Optic Cables Inside Power Structure X2 H1 H2 H3 H4 H5 H6 H7 Fiber Optic Adapter Board X3 +24V 1 Common 2 37 X2 (Slot A) 20C-DA1-A (24V dc Digital Input w/ Analog I/O) or 20C-DA1-B (115V ac Digital Input w/ Analog I/O) X3 (Slot B) 20C-DO1 (Digital Output Option) 700H Control Board X4 X5 (Slot C) (Slot D) Option Option Board Board X6 (Slot E) 20C-DPI1 (DPI Communications Option) X3 X2 X7 (RS-232 Programming Port) X2 DPI Interface X4 X3 20 DPI COMM (Option) J2 PWR STS PORT MOD NET A NET B HIM Bezel J1 HIM J3 HIM 10 Analog I/O 8 / 10 Digital Inputs 3 3 Digital Digital Outputs Outputs DPI Assembly 700H Control Assembly

13 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 13 Figure 8 Termination Points on Fiber Optic Adapter Board (700H Drives) Back View H7 H6 H5 H4 H3 H2 H1 X2

14 14 PowerFlex 700S and 700H Frame 11 Replacement Power Structures Pre-Charge Connections on Drives with DC Input You must connect the ASIC board connectors X9 and 5 to the X50 terminal block for the pre-charge circuit. The X50 terminal block is located on the Control Frame. Refer to the Installation Instructions - PowerFlex 700S and 700H High Power Drives, publication PFLEX-IN006, for information regarding the pre-charge circuit. X50 Terminal Block Connections ASIC Board Connector Terminal to X50 Terminal Pre-Charge Circuit Connection Description X Pre-charge Complete Signal (+24V DC) Pre-charge Complete Signal (Common) Charge Relay Contact Charge Relay Contact Figure 9 Sample Pre-charge Wiring Diagram Customer Connections - External precharge circuitry is shown as dashed lines. Terminal Block Drive Connections F1 M R1 CR2 DC+ M X X ASIC Board Precharge Complete DC Source Charge Relay* CR1 Pilot Relay M DC- F2 R2 CR2 CR1 M Main DC Contactor *Refer to the ASIC Board Charge Relay Contact Ratings table below. M CR2 Precharge Important: For DC Input Only. Do Not Install on AC Input Drives ASIC Board Charge Relay Contact Ratings Load Resistance load (cos φ = 1) Rated load 8 A at 250 VAC: 5 A at 30 VDC Rated carry current 8 A Max. switching voltage 250 VAC; 30 VDC, (400 VAC) Max. switching current AC 8 A; DC 5 A Max. switching power 2,000 VA; 150 W Failure rate (reference value) 5 VDC 10 ma (for gold plating 0.35 µ min.)

15 PowerFlex 700S and 700H Frame 11 Replacement Power Structures 15 Step 6: Installing the Product Identification Label on New Power Structure All frame 11 replacement power structures are shipped from the factory without a product identification label on the drive. If you are installing the power structure in a 700S drive, you should label it with the accompanying PowerFlex 700S label. If you are installing the power structure in a 700H drive, you should label it with the accompanying PowerFlex 700H label.! DANGER Risk of electric shock and death. Disconnect power, wait 5 minutes and verify DC bus voltage before servicing. Follow instructions in manual before use. Earth ground required. OR! DANGER Risk of electric shock and death. Disconnect power, wait 5 minutes and verify DC bus voltage before servicing. Follow instructions in manual before use. Earth ground required. Step 7: Starting the Drive 1. Install the protective covers on the drive. Refer to publication PFLEX-IN006, Installation Instructions - PowerFlex 700S and 700H High Power Drives, for assistance in installing these covers. 2. Start up the drive. Refer to the Start Up procedures in the appropriate publication: User Manual - PowerFlex 700S Drives with Phase II Control, 20D-UM006. Programming Manual - PowerFlex 700H Drives, 20C-PM001.

16 Reference Materials Allen-Bradley publications are available on the internet at The following manuals are recommended for general drive information: Title Publication Wiring and Grounding Guidelines for Pulse Width Modulated Drives DRIVES-IN001 Industrial Automation Wiring and Grounding Guidelines Preventive Maintenance of Industrial Control and Drive System Equipment DRIVES-TD001 Safety Guidelines for the Application, Installation and Maintenance of Solid SGI-1.1 State Control A Global Reference Guide for Reading Schematic Diagrams Guarding Against Electrostatic Damage The following manuals are recommended for detailed PowerFlex 700H and 700S information: Title Reference Manual - PowerFlex 700S Drives with Phase II Control User Manual - PowerFlex 700S Drives with Phase II Control Programming Manual - PowerFlex 700H Drives Installation Instructions - PowerFlex 700S and 700H High Power Drives Hardware Service Manual - PowerFlex 700S and 700H Frame 11 Drives Publication PFLEX-RM003 20D-UM006 20C-PM001 PFLEX-IN006 PFLEX-TG003 For Allen-Bradley Drives Technical Support: Title Online at... Allen-Bradley Drives Technical Support Power, Control and Information Solutions Headquarters Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI USA, Tel: (1) , Fax: (1) Europe/Middle East/Africa: Rockwell Automation, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium, Tel: (32) , Fax: (32) Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) , Fax: (852) Publication PFLEX-IN011C-EN-P - August P03 Supersedes PFLEX-IN011B-EN-P - March 2006 Copyright 2008 Rockwell Automation. All rights reserved. Printed in the U.S.A.

PowerFlex 700S and 700H Frame 13 Replacement Power Structures

PowerFlex 700S and 700H Frame 13 Replacement Power Structures Installation Instructions PowerFlex 700S and 700H Frame 13 Replacement Power Structures Introduction Use this document to install a replacement power structure on a PowerFlex 700S or 700H frame 13 drive.

More information

PowerFlex 700S Phase II Drives DriveLogix Option Card Battery Extension Cable

PowerFlex 700S Phase II Drives DriveLogix Option Card Battery Extension Cable Installation Instructions PowerFlex 700S Phase II Drives DriveLogix Option Card Battery Extension Cable!!!!! ATTENTION: To avoid an electric shock hazard, ensure that all power to the drive has been removed

More information

PowerFlex 700L Liquid-to-Liquid Heat Exchanger Control Board Replacement

PowerFlex 700L Liquid-to-Liquid Heat Exchanger Control Board Replacement Installation Instructions PowerFlex 700L Liquid-to-Liquid Heat Exchanger Replacement ATTENTION: To avoid an electric shock hazard and prevent thermal damage, ensure that all power to the drive power module

More information

PowerFlex DC Drive - Frame A Switching Power Supply Circuit Board

PowerFlex DC Drive - Frame A Switching Power Supply Circuit Board Installation Instructions PowerFlex DC Drive - Frame A Switching Power Supply Circuit Board ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan or implement

More information

Ferrite Core for Internal DPI Cables on PowerFlex 700S Frame 3 and 4 Drives

Ferrite Core for Internal DPI Cables on PowerFlex 700S Frame 3 and 4 Drives Installation Instructions Ferrite Core for Internal DPI Cables on PowerFlex 700S Frame 3 and 4 Drives ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged

More information

PowerFlex DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board

PowerFlex DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Installation Instructions PowerFlex DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board!!! ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should

More information

DriveGuard. Safe-Off Option for PowerFlex 70 AC Drives. User Manual.

DriveGuard. Safe-Off Option for PowerFlex 70 AC Drives. User Manual. DriveGuard Safe-Off Option for PowerFlex 70 AC Drives User Manual www.abpowerflex.com Important User Information Solid state equipment has operational characteristics differing from those of electromechanical

More information

PowerFlex 700 Power Jumpers

PowerFlex 700 Power Jumpers PowerFlex 700 Power Jumpers Installation Instructions The PowerFlex 700 drive contains protective s and Common Mode Capacitors referenced to ground (see below). To guard against unstable operation and/or

More information

SynchLink Board for PowerFlex 700S Drives with Phase II Control

SynchLink Board for PowerFlex 700S Drives with Phase II Control Installation Instructions SynchLink Board for PowerFlex 700S Drives with Phase II Control ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before

More information

PowerFlex DC Stand-Alone Regulator (SAR) Switching Power Supply Circuit Board

PowerFlex DC Stand-Alone Regulator (SAR) Switching Power Supply Circuit Board Installation Instructions PowerFlex DC Stand-Alone Regulator (SAR) Switching Power Supply Circuit Board ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan

More information

PowerFlex DC Stand-Alone Regulator (SAR) Power Interface Circuit Board

PowerFlex DC Stand-Alone Regulator (SAR) Power Interface Circuit Board Installation Instructions PowerFlex DC Stand-Alone Regulator (SAR) Power Interface Circuit Board ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan or implement

More information

PowerFlex DC Stand-Alone Regulator (SAR) Field Circuit Board

PowerFlex DC Stand-Alone Regulator (SAR) Field Circuit Board Installation Instructions PowerFlex DC Stand-Alone Regulator (SAR) Field Circuit Board ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan or implement the

More information

PowerFlex DC Stand-Alone Regulator (SAR) In-Rush Limiting Resistor

PowerFlex DC Stand-Alone Regulator (SAR) In-Rush Limiting Resistor Installation Instructions PowerFlex DC Stand-Alone Regulator (SAR) In-Rush Limiting Resistor ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan or implement

More information

ControlNet Comm Glass Fiber Adapter Kit

ControlNet Comm Glass Fiber Adapter Kit ControlNet Comm Glass Fiber Adapter Kit Instruction Manual D2-3565 ControlNet Comm Glass Fiber Adapter Kit Supplemental Information The following information is designed to supplement the ControlNet Adapter

More information

PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board

PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board Service Bulletin PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board Contents This publication provides instructions for replacing the gate power board for PowerFlex 400 Frame G and

More information

DriveTools SP v4.03 Software Patch

DriveTools SP v4.03 Software Patch Release Notes DriveTools SP v4.03 Software Patch This release note describes major revision 4, minor revision 3 of software for DriveTools SP. This patch is not a complete installation and only installs

More information

PowerFlex DC Drive Frame B Pulse Transformer Circuit Board

PowerFlex DC Drive Frame B Pulse Transformer Circuit Board Installation Instructions PowerFlex DC Drive Frame B Pulse Transformer Circuit Board ATTENTION: Only qualified personnel familiar with DC drives and associated machinery should plan or implement the installation,

More information

Drive Software Wizards v2.3

Drive Software Wizards v2.3 Release Notes Drive Software Wizards v2.3 This release notes describes major revision 2, minor revision 3 of drive software wizards for DriveExplorer (v5.02 and higher), DriveTools SP (v4.01 and higher)

More information

1203-SSS Smart Self-powered Serial Converter Firmware v3.007

1203-SSS Smart Self-powered Serial Converter Firmware v3.007 Release Note 1203-SSS Smart Self-powered Serial Converter Firmware v3.007 This release note describes major revision 3, minor revision 7 of firmware for the 1203-SSS converter. Important: Any firmware

More information

PowerFlex 700S Power Jumpers Frames 1 6

PowerFlex 700S Power Jumpers Frames 1 6 PowerFlex 700S Power Jumpers s 1 6 Installation Instructions The PowerFlex 700S drive contains protective s and ommon Mode apacitors referenced to ground (see below). To guard against unstable operation

More information

PowerFlex 755 Common DC Input Drives, Frames Interlock Assembly and Precharge Assembly Left-front Cover Retrofit Kit

PowerFlex 755 Common DC Input Drives, Frames Interlock Assembly and Precharge Assembly Left-front Cover Retrofit Kit Installation Instructions PowerFlex 755 Common DC Input Drives, Frames 8...10 Interlock Assembly and Precharge Assembly Left-front Cover Retrofit Kit Catalog Numbers 20G14x, 21G14x Topic Page General Precautions

More information

PowerFlex 700H Drive Firmware (Revision )

PowerFlex 700H Drive Firmware (Revision ) Release Notes PowerFlex 700H Drive Firmware (Revision 67.001) These release notes correspond to revision 67.001 of firmware for PowerFlex 700H drives. This document describes the differences between firmware

More information

PowerFlex 400 Drive Firmware Version 7.01

PowerFlex 400 Drive Firmware Version 7.01 Release Notes PowerFlex 400 Drive Firmware Version 7.01 Catalog Number 22C These release notes correspond to major version 7, minor version 1 of firmware for the PowerFlex 400 drive. The following information

More information

PowerFlex 755 Transition Section and Splicing Kit for Floormount Drives and CENTERLINE 2100 Motor Control Centers

PowerFlex 755 Transition Section and Splicing Kit for Floormount Drives and CENTERLINE 2100 Motor Control Centers Installation Instructions PowerFlex 755 Transition Section and Splicing Kit for Floormount Drives and CENTERLINE 2100 Motor Control Centers Topic Page Introduction, Compatibility 1 Additional Resources

More information

Allen-Bradley Drives

Allen-Bradley Drives (Cat. No. 1771-IE) Product Data The Analog Input Module (8-bit) (cat. no. 1771-IE) measures analog signals at its inputs and converts this data to 3-digit BCD values (0-255) for transfer to a PC processor.

More information

PowerFlex 7-Class Human Interface Module Series A Firmware v3.010

PowerFlex 7-Class Human Interface Module Series A Firmware v3.010 Release Note PowerFlex 7-Class Human Interface Module Series A Firmware v3.010 This release note describes major revision 3, minor revision 10 of firmware for the following: 20-HIM-A3 Series A 20-HIM-A5

More information

PowerFlex 700H AC Drive Safe Torque Off Option

PowerFlex 700H AC Drive Safe Torque Off Option User Manual PowerFlex 700H AC Drive Safe Torque Off Option Catalog Number 20C-DG01 Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical

More information

1203-SSS Smart Self-powered Serial Converter Firmware v3.006

1203-SSS Smart Self-powered Serial Converter Firmware v3.006 Release Note 1203-SSS Smart Self-powered Serial Converter Firmware v3.006 This release note describes major revision 3, minor revision 6 of firmware for the 1203-SSS converter. Important: Any firmware

More information

Drive Software Wizards v1.3

Drive Software Wizards v1.3 Release Notes Drive Software Wizards v1.3 These release notes describes major revision 1, minor revision 3 of drive software wizards for DriveExplorer (v5.02 and higher) and DriveTools SP (v4.01 and higher).

More information

20-COMM-M Modbus/TCP Adapter Firmware v2.001

20-COMM-M Modbus/TCP Adapter Firmware v2.001 Release Note 20-COMM-M Modbus/TCP Adapter Firmware v2.001 This release note describes major revision 2, minor revision 1 of firmware for 20-COMM-M Modbus/TCP adapters. Introduction The following information

More information

DriveGuard. Safe-Off Option for PowerFlex 700S Phase II AC Drives. User Manual.

DriveGuard. Safe-Off Option for PowerFlex 700S Phase II AC Drives. User Manual. DriveGuard Safe-Off Option for PowerFlex 700S Phase II AC Drives User Manual www.abpowerflex.com Important User Information Solid state equipment has operational characteristics differing from those of

More information

Drive Software Wizards v2.2

Drive Software Wizards v2.2 Release Notes Drive Software Wizards v2.2 This release notes describes major revision 2, minor revision 2 of drive software wizards for DriveExplorer (v5.02 and higher), DriveTools SP (v4.01 and higher)

More information

PowerFlex 400 AC Drive Guide Specification

PowerFlex 400 AC Drive Guide Specification PowerFlex 400 AC Drive Guide Specification Adjustable Frequency Drives with Bypass 3.0 50HP @ 208V AC 3.0 350HP @ 480V AC PART 1 GENERAL 1.01 Quality Assurance A. The manufacturer shall have minimum 5

More information

20-COMM-B BACnet MS/TP Adapter Firmware v1.002

20-COMM-B BACnet MS/TP Adapter Firmware v1.002 20-COMM-B BACnet MS/TP Adapter Firmware v1.002 Release Note This release note describes major revision 1, minor revision 2 of firmware for 20-COMM-B BACnet MS/TP adapters. Introduction The following information

More information

In this section we tell you how to initially handle your module, key your I/O chassis, install your module and make your wiring connections.

In this section we tell you how to initially handle your module, key your I/O chassis, install your module and make your wiring connections. Installation Data This document provides information on: important pre installation considerations power supply requirements installing the module connecting the wiring using the indicators on the module

More information

Embedded EtherNet/IP Option Card for DriveLogix 5730 Controllers

Embedded EtherNet/IP Option Card for DriveLogix 5730 Controllers Installation Instructions Embedded EtherNet/IP Option ard for DriveLogix 5730 ontrollers!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before

More information

This document provides information on: important pre-installation considerations installing the memory cartridge replacing the battery specifications

This document provides information on: important pre-installation considerations installing the memory cartridge replacing the battery specifications Installation Data This document provides information on: important pre-installation considerations installing the memory cartridge replacing the battery specifications The memory cartridge is shipped in

More information

Installation Data. The 1771 OB module can control the following output devices: dc motor starters indicators solenoids

Installation Data. The 1771 OB module can control the following output devices: dc motor starters indicators solenoids Installation Data This document provides information on: important pre installation considerations power supply requirements initial handling procedures installing the module using the indicators for troubleshooting

More information

Power Supply Chassis

Power Supply Chassis Power Supply Chassis Cat. No. 1771-PSC Installation Data This document contains information on: pre-installation considerations compatibility current limitations mounting considerations installation specifications

More information

Allen-Bradley 1397 L11 I/O Expansion Card

Allen-Bradley 1397 L11 I/O Expansion Card Installation Instructions IN Allen-Bradley 1397 L11 Expansion Card Cat. No. 1397-L11 What This Option Provides The Expansion Card is a drive mounted board that provides these additional signals. (5) Digital

More information

AB Spares. Installation Data

AB Spares. Installation Data Installation Data This document provides information on: important pre installation considerations power supply requirements initial handling procedures installing the module using the indicators for troubleshooting

More information

Allen-Bradley 1397 AC Tachometer Interface Card

Allen-Bradley 1397 AC Tachometer Interface Card Instructions Allen-Bradley 1397 AC Tachometer Interface Card Cat. No. 1397-AC Contents Topic Page What This Option Provides 1 Where This Option Is Used 1 What These Instructions Contain 1 Specifications

More information

Installation Instructions

Installation Instructions Installation Instructions Cat. No. 1771-IQ16 Series C This document provides information on: The dc isolated input module is shipped in static-shielded packaging to guard against electrostatic discharge

More information

1203-EN1 EtherNet/IP-to-SCANport Module Firmware v1.005

1203-EN1 EtherNet/IP-to-SCANport Module Firmware v1.005 Release Note 1203-EN1 EtherNet/IP-to-SCANport Module Firmware v1.005 This release note describes major revision 1, minor revision 5 of firmware for 1203-EN1 EtherNet/IP-to-SCANport modules. Introduction

More information

20-COMM-E EtherNet/IP Adapter Firmware v4.001

20-COMM-E EtherNet/IP Adapter Firmware v4.001 Release Note 20-COMM-E EtherNet/IP Adapter Firmware v4.001 This release note describes major revision 4, minor revision 1 of firmware for 20-COMM-E EtherNet/IP adapters. Introduction The following information

More information

22-COMM-B BACnet MS/TP Adapter Firmware v1.003

22-COMM-B BACnet MS/TP Adapter Firmware v1.003 22-COMM-B BACnet MS/TP Adapter Firmware v1.003 Release Note This release note describes major revision 1, minor revision 3 of firmware for 22-COMM-B BACnet MS/TP adapters. Introduction The following information

More information

Second Encoder Option Card for PowerFlex 700S Drives with Phase II Control

Second Encoder Option Card for PowerFlex 700S Drives with Phase II Control Installation Instructions Second Encoder Option ard for PowerFlex 700S Drives with Phase II ontrol!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged

More information

Application Guide. Considerations for 32 Bit Integer Parameters in 16 Bit Processors. PowerFlex 700VC, PowerFlex 700S. Introduction.

Application Guide. Considerations for 32 Bit Integer Parameters in 16 Bit Processors. PowerFlex 700VC, PowerFlex 700S. Introduction. Topic: Drive Product: Introduction User Information Considerations for 32 Bit Integer Parameters in 16 Bit Processors PowerFlex 700VC, PowerFlex 700S An Application Guide provides generic information on

More information

In this section we tell you how to key your I/O chassis, install your module and make your wiring connections.

In this section we tell you how to key your I/O chassis, install your module and make your wiring connections. Installation Data This document provides information on: power supply requirements initial handling procedures installing the module using the indicators for troubleshooting replacing the fuses module

More information

You cannot install the module unless the connector is fully extended. ATTENTION: Allen-Bradley HMIs

You cannot install the module unless the connector is fully extended. ATTENTION: Allen-Bradley HMIs This module mounts on a 1794 terminal base unit. 1. Rotate keyswitch (1) on terminal base unit (2) clockwise to position as required for this type of module. 2. Make certain the flexbus connector (3) is

More information

The ac input module is shipped in a static shielded bag to guard against electrostatic discharge damage. Observe the following precautions when

The ac input module is shipped in a static shielded bag to guard against electrostatic discharge damage. Observe the following precautions when Installation Data This document provides information on: important pre installation considerations power supply requirements initial handling installing the module using the indicators for troubleshooting

More information

DriveTools SP v5.03 Software Patch

DriveTools SP v5.03 Software Patch Release Notes DriveTools SP v5.03 Software Patch This release note describes major revision 5, minor revision 3 of software for DriveTools SP. This patch is not a complete installation and only installs

More information

20-WIM-Nx DPI Wireless Interface Module Firmware v1.003

20-WIM-Nx DPI Wireless Interface Module Firmware v1.003 20-WIM-Nx DPI Wireless Interface Module Firmware v1.003 Release Note This release note describes major revision 1, minor revision 3 of firmware for 20-WIM-Nx wireless interface module. Introduction The

More information

RGU Main Control Board Replacement Firmware Version 3.01

RGU Main Control Board Replacement Firmware Version 3.01 Replacement Kit Instructions RGU Main Control Board Replacement Firmware Version 3.0 Contents This document shows how to remove and replace the main control board in a Regenerative DC Bus Supply Unit (RGU).

More information

PowerFlex 755. Adjustable Frequency AC Drive. Drive Description. Contents. Conformity to Standards

PowerFlex 755. Adjustable Frequency AC Drive. Drive Description. Contents. Conformity to Standards PowerFlex 755 Adjustable Frequency AC Drive Drive Designed for ease of integration, application flexibility and performance, the PowerFlex 755 AC drive provides greater functionality across your manufacturing

More information

PowerFlex 700S Drives with Phase II Control (4.002)

PowerFlex 700S Drives with Phase II Control (4.002) Release Notes PowerFlex 700S Drives with Phase II Control (4.002) These release notes correspond to major revision (4), minor revision (2) of firmware for PowerFlex 700S drives with Phase II control. Introduction

More information

PowerFlex 753 Drives (revision 9.002)

PowerFlex 753 Drives (revision 9.002) Release Notes PowerFlex 753 Drives (revision 9.002) These release notes correspond to major revision 9, minor revision 2 of firmware for PowerFlex 753 drives. Introduction The following information is

More information

Kinetix 6000 Axis Module and Shunt Module

Kinetix 6000 Axis Module and Shunt Module Installation Instructions Kinetix 6000 and Shunt Module Catalog Numbers 2094-AMxx, 2094-BMxx 2094-AMxx-S, 2094-BMxx-S 2094-BSP2 Topic Page About This Publication 1 Important User Information 2 Before You

More information

PowerFlex 753 Drives (revision 1.007)

PowerFlex 753 Drives (revision 1.007) Release Notes PowerFlex 753 Drives (revision 1.007) These release notes correspond to major revision 1, minor revision 7 of firmware for PowerFlex 753 drives. Introduction The following information is

More information

20-COMM-H RS485 HVAC Adapter Firmware Revision 2.010

20-COMM-H RS485 HVAC Adapter Firmware Revision 2.010 Release Note 20-COMM-H RS485 HVAC Adapter Firmware Revision 2.010 This release note describes major revision 2, minor revision 10 of firmware for 20-COMM-H RS485 HVAC adapters. Introduction The following

More information

20-COMM-H RS485 HVAC Adapter Firmware Revision 2.009

20-COMM-H RS485 HVAC Adapter Firmware Revision 2.009 Release Note 20-COMM-H RS485 HVAC Adapter Firmware Revision 2.009 This release note describes major revision 2, minor revision 9 of firmware for 20-COMM-H RS485 HVAC adapters. Introduction The following

More information

DriveLogix 5730 Controller

DriveLogix 5730 Controller DriveLogix 5730 Controller for PowerFlex 700S Drives with Phase II Control Firmware Version 13.XX User Manual Important User Information Solid state equipment has operational characteristics differing

More information

(Cat. No P1) Installation Data

(Cat. No P1) Installation Data (Cat. No. 1771-P1) Installation Data Use this publication to install a 1771-P1 system power supply. You perform these tasks: prepare to install the power supply - install batteries into the battery pack

More information

20-COMM-P Profibus Adapter Firmware v1.006

20-COMM-P Profibus Adapter Firmware v1.006 Release Note 20-COMM-P Profibus Adapter Firmware v1.006 This release note describes major revision 1, minor revision 6 of firmware for 20-COMM-P Profibus adapters. Important: For this adapter, firmware

More information

PowerFlex 700S Drives - Phase II Control (Frame Sizes 9-13)

PowerFlex 700S Drives - Phase II Control (Frame Sizes 9-13) PowerFlex 700S Drives - Phase II Control (Frame Sizes 9-13) 1 Quick Start PowerFlex 700S Drives - Phase II Control (Frame Sizes 9-13) Introduction This document is designed to guide you through the basic

More information

Block I/O Cat. No IOBA and -IOBB Series B User Manual

Block I/O Cat. No IOBA and -IOBB Series B User Manual User Manual Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary

More information

(Catalog Numbers 1394-FK10TS and -FK22TS)

(Catalog Numbers 1394-FK10TS and -FK22TS) Installation Instructions 1394 Fan Kit (Catalog Numbers 1394-FK10TS and -FK22TS) This publication provides installation instructions for the Allen-Bradley 1394 fan kit. The fan kit applies to the following

More information

PowerFlex 20-HIM-A6 and 20-HIM-C6S HIM Firmware Revision 1.006

PowerFlex 20-HIM-A6 and 20-HIM-C6S HIM Firmware Revision 1.006 Release Note PowerFlex 20-HIM-A6 and 20-HIM-C6S HIM Firmware Revision 1.006 This release note describes major revision 1, minor revision 6 of firmware for PowerFlex 20-HIM-A6 and 20-HIM-C6S HIMs (Human

More information

PowerFlex 755 Drives (revision 2.009)

PowerFlex 755 Drives (revision 2.009) Release Notes PowerFlex 755 Drives (revision 2.009) These release notes correspond to major revision 2, minor revision 9 of firmware for PowerFlex 755 drives. Introduction The following information is

More information

PowerFlex 753 Drives (revision 1.011)

PowerFlex 753 Drives (revision 1.011) Release Notes PowerFlex 753 Drives (revision 1.011) These release notes correspond to major revision 1, minor revision 11 of firmware for PowerFlex 753 AC drives. Introduction The following information

More information

Regulator Board Installation Instructions for WebPak 3000 Version 1.x Drives

Regulator Board Installation Instructions for WebPak 3000 Version 1.x Drives Regulator Board Installation Instructions for WebPak 3000 Version 1.x Drives M/N 920WK0011 Instruction Manual D2-3465! ATTENTION: Only qualified personnel familiar with the construction and operation of

More information

PowerFlex 753 Drives (revision 1.009)

PowerFlex 753 Drives (revision 1.009) Release Notes PowerFlex 753 Drives (revision 1.009) These release notes correspond to major revision 1, minor revision 9 of firmware for PowerFlex 753 drives. Introduction The following information is

More information

Installation Data. The 1771 IH module is compatible with the following 2 wire devices: pushbuttons limit switches float switches selector switches

Installation Data. The 1771 IH module is compatible with the following 2 wire devices: pushbuttons limit switches float switches selector switches Installation Data This document provides information on: important pre installation considerations power supply requirements initial handling procedures installing the module using the indicators for troubleshooting

More information

PCI Expansion Slot Kit for 6181P (1500P) Series D Integrated Display Computer

PCI Expansion Slot Kit for 6181P (1500P) Series D Integrated Display Computer Installation Instructions PCI Expansion Slot Kit for 6181P (1500P) Series D Integrated Display Computer Catalog Number 6189V-2PCI15R Topic Page About This Publication 1 Important User Information 2 Safety

More information

In this section we tell you how to key your I/O chassis, install your module and make your wiring connections.

In this section we tell you how to key your I/O chassis, install your module and make your wiring connections. Installation Data This document provides information on: important pre installation considerations power supply requirements initial handling procedures installing the module using the indicators for troubleshooting

More information

Block I/O Cat. No IOBA and -IOBB User Manual

Block I/O Cat. No IOBA and -IOBB User Manual User Manual Because of the variety of uses for this product and because of the differences between solid state products and electromechanical products, those responsible for applying and using this product

More information

Installation Instructions

Installation Instructions Installation Instructions (Cat. No. 1794-TBN) 6 1 5 9 4 2 3 10 6 7 8 Component Identification 1 Female flexbus connector 2 Terminal base unit (1794-TBN) 3 Male flexbus connector 4 Keyswitch Set to the

More information

PowerFlex 755 Drives (revision 4.002)

PowerFlex 755 Drives (revision 4.002) Release Notes PowerFlex 755 Drives (revision 4.002) These release notes correspond to major revision 4, minor revision 2 of firmware for PowerFlex 755 drives. Introduction The following information is

More information

PowerFlex 753 Drives (revision 1.010)

PowerFlex 753 Drives (revision 1.010) Release Notes PowerFlex 753 Drives (revision 1.010) These release notes correspond to major revision 1, minor revision 10 of firmware for PowerFlex 753 AC drives. Introduction The following information

More information

AB PLCs. (Cat. No E1, -E2, -E3)

AB PLCs. (Cat. No E1, -E2, -E3) (Cat. No. 1771-E1, -E2, -E3) Product Data Analog Input Expander Modules (cat. no. 1771-E1 -E2, -E3) are used with an Analog Input Module (12-bit) Assembly (cat. no. 1771-IF, series B). They provide a cost

More information

Altivar 61/71 Adjustable Speed Drives Heatsink Fan Kits VZ3V1212 and VZ3V1216

Altivar 61/71 Adjustable Speed Drives Heatsink Fan Kits VZ3V1212 and VZ3V1216 Altivar 61/71 Adjustable Speed Drives Heatsink Fan Kits VZ3V1212 and VZ3V1216 Instruction Bulletin 30072-452-48 Retain for future use. 30072-452-48 Altivar 61/71 Heatsink Fan Kits VZ3V1212 and VZ3V1216

More information

The 1784-KR is a half-slot module that resides in any available expansion slot in an IBM XT (except slot J8) or AT compatible computer.

The 1784-KR is a half-slot module that resides in any available expansion slot in an IBM XT (except slot J8) or AT compatible computer. This document shows you how to install the 1784-KR module. Do not attempt to install the module until you have read this document. It contains the following sections: The 1784-KR module provides an interface

More information

CompactBlock Guard I/O EtherNet/IP Safety Modules

CompactBlock Guard I/O EtherNet/IP Safety Modules Installation Instructions CompactBlock Guard I/O EtherNet/IP Safety Modules Catalog Numbers 1791ES-IB8XOBV4, 1791ES-IB16 Topic Page Important User Information 2 North American Hazardous Location Approval

More information

PowerFlex 523 AC Drive

PowerFlex 523 AC Drive PowerFlex 523 AC Drive PowerFlex 523 AC drives are designed to help reduce installation and configuration time with an innovative modular design while providing just enough control for your application.

More information

Digital ac/dc (24V) Input Module

Digital ac/dc (24V) Input Module Installation Instructions Digital ac/dc (24V) Input Module Catalog Number 1771-IND, Series C Topic Page Important User Information 2 Before You Begin 3 Power Requirements 3 Prevent Electrostatic Discharge

More information

Artisan Scientific is You~ Source for: Quality New and Certified-Used/Pre:-awned ECJuiflment

Artisan Scientific is You~ Source for: Quality New and Certified-Used/Pre:-awned ECJuiflment Looking for more information? Visit us on the web at http://www.artisan-scientific.com for more information: Price Quotations Drivers Technical Specifications. Manuals and Documentation Artisan Scientific

More information

In this section we tell you how to key your I/O chassis, install your module and make your wiring connections.

In this section we tell you how to key your I/O chassis, install your module and make your wiring connections. Installation Data This document provides information on: important pre installation considerations power supply requirements initial handling procedures installing the module using the indicators for troubleshooting

More information

Installing Your 1394 Drive Interface Module

Installing Your 1394 Drive Interface Module Installation Instructions Installing Your Drive Interface Module (Catalog Number -DIM) Introduction This publication provides installation instructions for adding the Drive Interface Module to your system.

More information

Logix5000 Control Systems: Connect a PanelView Plus Terminal over an EtherNet/IP Network

Logix5000 Control Systems: Connect a PanelView Plus Terminal over an EtherNet/IP Network Quick Start Logix5000 Control Systems: Connect a PanelView Plus Terminal over an EtherNet/IP Network Catalog Numbers Logix5000 Controllers, 2711P PanelView Plus Terminals Important User Information Solid-state

More information

Installation Instructions

Installation Instructions Installation Instructions This document provides information on: important pre-installation considerations power supply requirements initial handling procedures installing the module using the indicators

More information

1. Turn off power to the I/O chassis.

1. Turn off power to the I/O chassis. Installation Data This document provides information on: important pre installation considerations power supply requirements installing the module using the indicators for troubleshooting module specifications

More information

Kinetix 2000 Integrated Axis Module and Axis Module

Kinetix 2000 Integrated Axis Module and Axis Module Installation Instructions Kinetix 2000 Integrated Axis Module and Axis Module Catalog Numbers 2093-AC05-MP1, 2093-AC05-MP2, 2093-AC05-MP5, 2093-AMP1, 2093-AMP2, 2093-AMP5, 2093-AM01, 2093-AM02 Topic Important

More information

24/48/120 VAC Interface Card Instruction Manual

24/48/120 VAC Interface Card Instruction Manual 24/48/120 VAC Interface Card Instruction Manual Distributed by Ergonomic Partners Sales@ErgonomicPartners.com www.ergonomicpartners.com Tel: (314) 884-8884 April 2012 Part Number: -R2 Copyright 2012 Magnetek

More information

PowerFlex 70 Safe-Off Control EtherNet/IP Guard I/O Safety Module and GuardLogix Integrated Safety Controller

PowerFlex 70 Safe-Off Control EtherNet/IP Guard I/O Safety Module and GuardLogix Integrated Safety Controller Safety Application Example PowerFlex 70 Safe-Off Control EtherNet/IP Guard I/O Safety Module and GuardLogix Integrated Safety Controller Safety Rating: Category 3 (also see Achieving a Cat. 4 Safety Rating)

More information

Using TLS3-GD2 Guardlocking Interlock with ArmorBlock Guard I/O and SmartGuard Controller

Using TLS3-GD2 Guardlocking Interlock with ArmorBlock Guard I/O and SmartGuard Controller Safety Application Example Using TLS3-GD2 Guardlocking Interlock with ArmorBlock Guard I/O and SmartGuard Controller Guardlocking with On-machine Components Safety Rating: Category 3, according to EN954-1

More information

PowerFlex 700 Adjustable Frequency AC Drive

PowerFlex 700 Adjustable Frequency AC Drive Installation Instructions PowerFlex 700 Adjustable Frequency AC Drive Frames 7 10 160 500 kw (250 700 Hp) When reading this document, look for this symbol Step x to guide you through the 5 BASIC STEPS

More information

PowerFlex 753 Drives (revision )

PowerFlex 753 Drives (revision ) Release Notes PowerFlex 753 Drives (revision 11.001) These release notes correspond to major revision 11, minor revision 1 of firmware for PowerFlex 753 drives. Introduction The following information is

More information

Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout

Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Installation Instructions Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Catalog Numbers 2711-NR5T, 2711P-RAT12E2 Topic Page About This Publication 1 Important User Information 2 About

More information

GuardLogix: TLS Guardlocking Application

GuardLogix: TLS Guardlocking Application Safety Application Example GuardLogix: TLS Guardlocking Application Safety Rating: PLd, Cat. 3 to EN ISO 13849.1 2008 Introduction... 2 Important User Information... 2 General Safety Information... 3 Description...

More information

PowerFlex 525 AC Drive

PowerFlex 525 AC Drive PowerFlex 525 AC Drive PowerFlex 525 AC drives feature an innovative, modular design offering fast and easy installation and configuration. These cost-effective compact drives come with embedded EtherNet/IP

More information