Instructions for installing your QuiltCam on your Gammill quilt machine.
|
|
- Angel Hampton
- 6 years ago
- Views:
Transcription
1 Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video camera mounted in a holder with a stylus holder, see Figure 3 Stylus mounting bracket, see Figure 3 Video Monitor, See Figure 4 Video Monitor mounting bracket Cable clips Stylus Rod Screws and Nuts Figure 1 Figure 2 Figure 3 Figure 4
2 Step #1 Mounting the stylus To mount the stylus on your Gammill quilt machine you will need the large allen wrench that should have come with your quilt machine. On the side of the quilt machine you will find the stylus holder that came with the machine, see Figure 5. Using the allen wrench (5mm) remove both screws, save the screws as you will be reusing them. Figure 5 Slip one of the washers that came with the QuiltCam kit over each screw you just removed. Take the new stylus holder with the camera mounted into and position it in the same place you just removed the old holder from, see Figure 6. Replace the screws and tighten them with the allen wrench. Make sure the stylus is as level as you can get it side to side. I have found that the screw holes on the Gammill may not be level. Figure 6
3 Step #2 Mounting the control box The control box comes with two 3M command strips mounted on the back of it. Remove the paper off of the command strips and find a nice flat space on the back of the machine to place the control box that is not in the way of the thread path. I would recommend one side of the quilt machine close enough to reach the wires from the camera. Plug the wire from the video camera into the control box, the yellow plug goes into the yellow plug, and black plug goes to the red plug. The shorter cord runs to the video monitor. The longer cable coming out of the control box on the bottom is the power plug and you can run it along the power cord for your quilt machine. Do not plug it in yet. Step #3 Mounting the Video Monitor. The monitor mounts at the front on top of the head of the Gammill, see Figure 7. Figure 7 Find the monitor mount, see Figure 8 Figure 8
4 The mount uses double face tape to mount on top of the machine's head. I would recommend using some alcohol wipes to clean the top off before placing the mount, if you don't have any alcohol wipes, you can use finger nail polish remove and a paper towel. Once the surface is clean remove the paper off the bottom of the mount, see Figure 9. Figure 9 Carefully place the mount on top of the Gammill head, see figure 10. Press and hold the metal plate down onto the Gammill head for a few minutes to make sure the tape sticks Figure 10
5 Figure 11 Loosen the nut with the knob on the back of the black monitor mount just so the nut is loose. The nut on the monitor mount needs to slide into the grove on the back of the monitor see Figure 11. Once the nut is loose, slide the monitor over the nut and tighten the black knob. Figure 12 You can move the monitor up or down or change viewing angles by loosening one or the other black knobs on the monitor mounting bracket and adjusting the angle to suit your needs. Be sure to tighten both knobs when done making any adjustments Using the cable clips, run the cable from the monitor to the control box by placing the clips on the top or sides of the quilt machine making sure it is out of the way of the thread. The monitor cable plugs into the control box monitor cable, the plug is keyed so it should only fit one way. When placing the cable clips make sure they are out of the way of your thread pathway. Plug the power supply into the power cable coming out of the control box. Then plug the power supply into a power outlet. You may want to tape the power cable to your quilt machine's power cord to keep things clean. Your installation of the QuiltCam is complete and is now ready for you to use.
6 To use your QuiltCam Make sure your QuiltCam in plugged in and make sure your quilt machine is turned on. On the front of the control box you will find a silver and green button, push the button to turn the system on, and push the button again to turn it off. A green light around the button will turn on when the system in on and powered up. If the light does not come on and the button is pushed in, make sure the power supply is plugged in at both locations. Once the control box is turned on, push the little silver button on the bottom right hand side of the video monitor to turn on the video monitor. Happy quilting. If you have any problems with installing your QuiltCam please contact us at: R&S Design Ron Moorehead rmooreh@rns-design.com
Q2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationInstalling the Server into a Rack
Installing the Server into a Rack Note These instructions apply to multiple models; illustrations may vary slightly. Rack Mount Kit Inventory Before installing the chassis on a standard 4-post rack, make
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationAssembly Instructions for #5630 Medication PalWOW
Assembly Instructions for #5630 Medication PalWOW Before assembling, please familiarize yourself with all the parts and check to make sure you have all the parts as listed below. A B A & B - The box in
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationFLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N
FLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N 5-0083-00 TOOLS REQUIRED - 3/4" SOCKET - 3/4" WRENCH - /3" WRENCH - PHILLIPS SCREW DRIVER - TORQUE WRENCH INSTRUCTION P/N 6-0083-00 ISSUED: 3//7 SHEET
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationHOW TO INSTALL NEST BOX CAMERAS IN SCHWEGLER NO. 17 SWIFT NEST BOXES
HOW TO INSTALL NEST BOX CAMERAS IN SCHWEGLER NO. 17 SWIFT NEST BOXES By Lynda and Chris Huxley natureofireland@eircom.net January 2015 1. The nest box cameras are colour in daylight, plus infrared in darkness
More informationInstallation Guide. Universal Camera Mount Bracket
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Universal Camera Mount Bracket The purpose of this guide is to describe the assembly and
More informationKRONOS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TABLE OF CONTENTS ENCLOSURE AND DONGLE ASSEMBLY 1 LIGHTED ENCLOSURES 2-10 2 SLIM ENCLOSURE 11-17 3 WIRED-ETHERNET DONGLE 18-25 4 REAR-OFFSET MOUNT 26-33 5 SIDE-MOUNT 34-41 6 SURFACE
More informationForeseesons Monitor Installation Instructions
Foreseesons Monitor Installation Instructions Visit the Merit Entertainment Web site http://www.meritind.com PM0626-04 Table of Contents Parts List... p. 1 Cabinet Identification... p. 1 Cabinets with
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationMPS-850 e-drum set. assembly instructions
MPS-850 e-drum set assembly instructions Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 16.10.2018,
More informationMotorola Moto G4 Plus Motherboard Replacement
Motorola Moto G4 Plus Motherboard Replacement Remove and replace your motherboard as a prerequisite to other guides. Written By: Andre Rives ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationNikon Focus Drive Manual
Nikon Focus Drive Manual PRIOR SCIENTIFIC INC., 80 RESERVOIR PARK DRIVE, ROCKLAND, MA 02370-1062 TELEPHONE 781-878-8442 FAX 781-878-8736 WWW.PRIOR.COM Table of Contents Safety Information...1 Unpacking
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More information3D SYSTEMS University CubeX 3D Printer
3D SYSTEMS University CubeX 3D Printer Lesson Leveling the Print Pad and Print Tips, Setting the Z-Gap Revision date: 10/22/13 1 1 2016 年 6 月 14 日 Objectives After completing this lesson you will: Be able
More informationSetup Information Panosaurus May 3, 2011
Setup Information Panosaurus 2.0 www.gregwired.com May 3, 2011 Please take the time to read all of the setup information to ensure success and ease of use of this tripod head. Much of the setup is a one
More informationColorMaxLP Label Roll Rewinder
ColorMaxLP Label Roll Rewinder 5/2017 INSTALLATION/OPERATOR MANUAL Included: Rewinder Base plate Power supply Power Cord Thumb screws Assembly instructions 1. Install base plate Lift front of printer and
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationCharging Cabinet Owner s Manual
by edugear Charging Cabinet Owner s Manual Before using, please read these operating instructions carefully. They contain important advice concerning the use and safety of your Charging Cabinet. The Charging
More informationCLIMB2 DUAL MONITOR SIT/STAND WORKSTATION
CLIMB2 DUAL MONITOR SIT/STAND WORKSTATION CLIMB2 Rev A 3/17 Model CLIMB2-SLV ASSEMBLY AND ADJUSTMENT CLIMB2 PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationCINTENNA ANTENNA REPAIR GUIDE
The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter
More informationFigure 4-29 Removing the CPU compartment cover
4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationInstallation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays
Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays Model: DS-VWT955-2X2 EXTENSION COLUMN (SOLD SEPARATELY) COMPATIBILITY Display width must be a minimum of 36"
More informationParts List: Assembly Instructions:
My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord
More informationReplacement Keyswitch Assembly
Installation Instructions Replacement Keyswitch Assembly (Catalog No. 2711E-NKSW1) Applicable Terminals Use this replacement keyswitch with PanelView Terminals 2711-KA1, -KC1, -TA1, -TC1, -TA4, -TC4 and
More informationEVOLVE1-M MONITOR ARM
EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before
More informationPrint Mechanism Maintenance Kit
Print Mechanism Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the print mechanism maintenance kit in the following printers: ZT0 ZT0 ZT0 Read
More informationCodonics Virtua Virtua-2 Optical Drive Replacement
Codonics Virtua Virtua-2 Optical Drive Replacement Technical Brief Overview This document describes the procedure for replacing an optical drive on a Codonics Virtua Medical Disc Publisher, Virtua-2 model.
More informationTECHKNOW, INC. Kiosk Order Confirmation System INSTALLATION MANUAL. Revision Date: July 11, 2012 Part # Version 3.2
document Page 1 of 18 TECHKNOW, INC Kiosk Order Confirmation System INSTALLATION MANUAL Revision Date: July 11, 2012 Part # Version 3.2 Techknow, Inc. 393 Mayfield Road Duncan, SC 29334 www.gotechknow.com
More informationNAV-1 Lens Support. NAV-2 Lens Support BEFORE YOU BEGIN
INSTALLATION Lens Support INSTRUCTIONS The Lens Support is compatible with any RPA projector mount. The readily adapts to the following ScreenStar Conversion Lens from Navitar: SSW08 and SST120. LENS SUPPORT
More informationFloppy Disk To USB. Converter Installation and. Operation Manual
Floppy Disk To USB Converter Installation and Operation Manual Kit Price $125.00 Plus Shipping Why Should I Change My Floppy Drive To A USB Drive? You won't ever need floppies anymore and yet you'll be
More informationSetting Up the Polycom Instructor FS HDX
Setting Up the Polycom Instructor FS HDX Version.5 February 008 Edition 75-7077-00/A Version.5 Trademark Information Polycom, the Polycom logo design are registered trademarks of Polycom, Inc. and Instructor
More informationSATALIGHT ASSEMBLY INSTRUCTIONS
SATALIGHT ASSEMBLY INSTRUCTIONS SATALIGHT STAND AND PROJECTOR INSTALLATION It is our recommendation, before installing the satalight, to have the IT staff install SMART Notebook software on the computer
More informationPFPDARM3 Product Illustration
PFPDARM3 Product Illustration page 1 of 15 PFPDARM3 Components & Fasteners 1x 1x 4x 4x 8x 4x 1 each TOOLS REQUIRED Phillips Screwdriver 1/2" Wrench 1/2" Socket Wrench 3/32" (2.38mm) 3/16" (4.76mm) 1/8"
More informationS Series Stand Assembly Instructions
S Series Stand Assembly Instructions Contents Stand Base Column Transducer holder Magnetic screwdriver, Allen bit & Phillips bit Grommets (4) Allen wrench 8mm Phillips-head screws (4) 12mm Allen-head screws
More informationReplacing the Encoder Strip
6-1-11. Replacing the Encoder Strip The following describes the procedure for replacing the Encoder Strip. Refer to the diagram below for identifying the parts and their positions. (The numbers shown in
More informationInstallation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio
Introduction The following instruction procedure is for the RGB interface to a GM 05 Nav Radio as part of the Webasto Product NAVCam Back-up Camera (VCP-0000220). In addition, an installer will need to
More informationMicroscopic Imaging Research Station (MIRS) Assembly Guide. Version 1.0.0
Microscopic Imaging Research Station (MIRS) Assembly Guide www.adsyscontrols.com Adsys Controls, Inc.2012 Version 1.0.0 I. Assembly of the Adsys Controls MIRS system This document explains the assembly
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More informationMounting on the Ceiling Using Flush Mount (Face Down)
Mounting on the Ceiling Using Flush Mount (Face Down) Installation Guide 2014/02/14 Table of Contents Safety Information... 3 Installation Procedures... 5 Step 1: Drill a Hole on the Ceiling... 5 Step
More information13 MMC for PC Option Modules
Part Number M.1300.8684 MMC for PC Option Modules Manual V3.0 The information in this document is also available in the MMC for PC Hardware Manual. 13 MMC for PC Option Modules 13.1 General The MMC for
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationExtra Large Full Motion TV Mount for Televisions
8008981 TV Size Range: 47 ~ 84 Maximum Weight Capacity: 60 kg/132 lbs Maximum Mounting Pattern: 800 mm x 600 mm (31.4 x 23.6 ) Distance to the Wall: 5.5-45 cm Extra Large Full Motion TV Mount for 47-84
More informationDMD Extender. Application Note 1 Sega Large Screen LCD Replacement. V0.1 October 2013 Copyright 2013 Dr Pinball
DMD Extender Application Note 1 Sega Large Screen LCD Replacement V0.1 October 2013 Copyright 2013 Dr Pinball Important This document is a guide to installing an LCD panel to replace a plasma display in
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationRequired Tools. Ford Transit Connect J4075 with R16 Tracks TRANSIT CONNECT 69 RAIL IBI. Marker. 7/16 / 9/16 / 1/2 Wrench.
IBI Required Tools INSTRUCTION MANUAL Marker 7/16 / 9/16 / 1/2 Wrench Drill with 3/8 Drill Bit Allen Key Ford Transit Connect J075 with R16 Tracks Part # J075 Rails 96 Bars 55 [ ] BLACK WHITE SILVER [
More informationHow to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit
Instructional Video Series How to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit Skill Level: Challenging Time to Complete: Approximately 45 Minutes Required
More informationimac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationWritten By: Sam Lionheart
iphone 5c Front Panel Replacement Replace the Front Panel on your iphone 5c. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION For an easier repair, use our fix kit
More informationBreeze Film Shooting Equipment (P-W5P-BRZ) I N STR UC TI ON MANUAL
Breeze Film Shooting Equipment (P-W5P-BRZ) I N STR UC TI ON MANUAL All rights reserved No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any means,
More informationIf you are missing any of the following items, please contact Stanton Video immediately (602)
RIGHT ANGLE FOCUS Jan 03 If you are missing any of the following items, please contact Stanton Video immediately (602) 493-9505 1. Right Angle Focus Servo 2. Servo End Cap 3. Lens Gears (32 pitch, 48 pitch,.6
More informationCARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS
CARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS CAUTION: The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the printhead. Please
More informationAssembly Guide T9200, T9500, T9600, AND T9700 PLATFORM TREADMILLS
Assembly Guide T9200, T9500, T9600, AND T9700 PLATFORM TREADMILLS Assembly Guide T9200, T9500, T9600, AND T9700 PLATFORM TREADMILLS To avoid possible damage to this Platform Treadmill, please follow these
More informationDescription: Detailed procedure on removing old bushing and installing new Brake Bushing Replacement Kit 10447
Procedure: BRAKE BUSHING REPLACEMENT PROCEDURE Product: Document #: Rev: Page: MODEL 7000, 7000A, & 8000 GYRO 078 1 1 of 14 Description: Detailed procedure on removing old bushing and installing new Brake
More informationFurther Information can be found at
Below is a step by step guide to assembling the Hurricane-Rig. Remember that this is a precision optical instrument. Excessive force can bend critical parts. If treated well it should give many years of
More informationIBM. Rack Installation Instructions
IBM Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following:
More informationSF Studio Series Set-Up Instructions
SF Studio Series Set-Up Instructions Teleprompter Parts Step #1 Remove the quick-release plate from your tripod head. Set the plate on a flat surface (table, desk, etc) with anti-skid pads on top & camera
More informationLED Lighting Kit For Elara NanoEdge Fixed Frame. Installation Guide. Attention: Read this guide before assembling your screen.
LED Lighting Kit For Elara NanoEdge Fixed Frame Installation Guide Attention: Read this guide before assembling your screen. INTRODUCTION GETTING STARTED WARNING - Sharp Edges This product may contain
More informationPowerBook G4 Aluminum 12" GHz Logic Board Replacement
PowerBook G4 Aluminum 12" 1-1.5 GHz Logic Board Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION This motherboard includes all ports except the DC-In board. TOOLS:
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following: v Two
More informationWide angle lens mods for Hubsan x4 h1207c
Wide angle lens mods for Hubsan x4 h1207c with HD camera I wanted a wide angle lens for this quad, so got a D-lens (120degree) lens module for 808 Keychain Camera off ebay for about 7. I followed a video
More informationInstalling 6 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing 6 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Overview...5 Installing the
More information25 Sport Scope Instruction Manual
25 Sport Scope Instruction Manual Dear Customer, We appreciate your business and value your support for our product. At Sport Scope, we strive to provide our customers with quality, easy to use, and affordable
More informationBL-FLOWSTN-P FlowStation Module Installation Guide
Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port
More informationINSTALLATION INSTRUCTIONS Version 2.4
INSTALLATION INSTRUCTIONS Version 2.4 11/12/2012 Patient Point, LLC 8230 Montgomery Road, Suite 300 Cincinnati, Ohio 45236 1-800-287-0908 TABLE OF CONTENTS System Overview 2 Tool List. 3 Installation Process
More informationLENS ATTACHMENT KIT INSTALLATION GUIDE
XM2 and XMU LENS ATTACHMENT KIT INSTALLATION GUIDE for Paladin and Phoenix lenses The XM2 Plate system attaches directly to many Epson, JVC and Sony home theater projectors OR it can be sandwiched between
More information2001 Dynojet Research, Inc. All Rights Reserved. CPU Module Installation Guide
2001 Dynojet Research, Inc. All Rights Reserved. This manual is copyrighted by Dynojet Research, Inc., hereafter referred to as Dynojet, and all rights are reserved. This manual, as well as the software
More informationMi50 Inverted Microscope User s Manual. Fein.
Mi50 Inverted Microscope User s Manual Fein info@feinoptic.com Mi50 Microscope Components Siedentopf Trinocular Head Stage Plate Mechanical Stage Locking Screw Hex Wrench Storage Beam Splitter Dust Protector
More informationHolz-Her Sliding Table Saw Kit Installation Instructions: For 1243 Rip Kits
Holz-Her Sliding Table Saw Kit Installation Instructions: For 1243 Rip Kits Please note this installation kit is designed solely for installation on Holz-Her Sliding Panel Saws, Model 1243 (may also fit
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS AUDIO UNIT P/N 08A70-MJN-A00 CTX1300/D MII 14925 Issue Date April 2014 PARTS LIST (11) (8) (2) TOOLS AND SUPPLIES REQUIRED Socket (10 mm)
More information21 TRACK MAINTENANCE GUIDE
Mountain Engineering II, Inc. 21 TRACK MAINTENANCE GUIDE 1233 Sherman Drive, Longmont, CO 80501-6133 303-651-0277 303-651-6371 (fax) www.mountainengineering.com Table of contents Table of contents...2
More informationThe Craftsmen (2) In (1) 500 Scooter/Wheelchair Carrier
The Craftsmen (2) In (1) 500 Scooter/Wheelchair Carrier Installation Manual LCI Toll Free: (866) 868-9694 Fax: (586) 232-4394 66 E Ten Mile Rd. Hazel Park Mi. 48030 PARTS LIST PART #: A101 BLACK SQUARE
More informationTASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS
TASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions. Save these instructions. The most up-to-date warnings and instructions are available at www.taser.com
More informationMac Mini Mid 2011 SSD Dual Drive Installation
Mac Mini Mid 2011 SSD Dual Drive Installation Install a second hard drive in your mid 2011 Mac Mini. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 19 INTRODUCTION Use this guide to install
More informationTyler - Middle Mount For Bell 407, 206 & 206L Series Helicopters FAA STC # SH3246NM
MIDDLE MOUNT 407 / JET RANGER / LONG RANGER INSTALLATION MANUAL Tyler - Middle Mount For Bell 407, 206 & 206L Series Helicopters FAA STC # SH3246NM PLEASE RETURN THIS MANUAL WITH EQUIPMENT This manual
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationReplacement Instructions
imac G5 Inverter, 20-inch Replacement Instructions Follow the instructions in this document carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Online
More informationSTEP-BY-STEP INSTRUCTIONS FOR BUILDING A MICHELSON INTERFEROMETER. TECHSPEC Optical Cage System
STEP-BY-STEP INSTRUCTIONS FOR BUILDING A MICHELSON INTERFEROMETER TECHSPEC Optical Cage System INTRODUCTION 2 What is a Michelson Interferometer? A Michelson Interferometer is a simple interferometric
More informationInstallation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit
Installation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter on Arm (page 2). 2.
More informationAssembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #
Assembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #7521002 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationRedEdge-M TM / DJI Inspire 1 Quick Mount INTEGRATION GUIDE
RedEdge-M TM / DJI Inspire 1 Quick Mount INTEGRATION GUIDE P/N: 900-00013 Rev 01 - Apr 2018 Table of Contents Thank you for your purchase! 1 What s inside? 1 What s Required? 2 Let s get started! 2 Assembling
More informationDual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines Installation Instructions (Kit # )
Please read thoroughly before starting installation and check that kit contents are complete. Items Included in Kit: Chassis Harness Power Harness with RCA connectors Camera mounted on license plate bracket
More informationOPERATING INSTRUCTIONS:
List OPERATING INSTRUCTIONS: Preparation For Installation, Product Identification Charging The Batteries ing And Adjusting The Lift Mounting Head s Brackets Mounting Clamps And Quick-Locking Arms Installation
More informationPowerBook G4 Aluminum 12" GHz Display Data Cable Replacement
PowerBook G4 Aluminum 12" 1-1.5 GHz Display Data Cable Replacement Written By: Matthew Newsom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 47 INTRODUCTION Replace a damaged display data cable to restore
More informationPowerBook G4 Aluminum 17" GHz Heat Sink & Fan Assembly Replacement
PowerBook G4 Aluminum 17" 1-1.67 GHz Heat Sink & Fan Assembly Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION The heat sink and fan together help to keep the
More informationReplacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638
Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638 This kit contains detailed instructions on removing a Galaxy II Daewoo monitor and replacing it with a 19 wide flat screen monitor.
More informationFitting An Emulator into the Yamaha AR Organ
Fitting An Emulator into the Yamaha AR Organ As performed by Les White and Frank Kemplay May 2011 On the upper rear panel remove the top line of 3 screws to allow removal of the top board assemblywhich
More informationimac Intel 27" EMC 2309 and 2374 Hard Drive
imac Intel 27" EMC 2309 and 2374 Hard Drive Replacement imac Intel 27" EMC 2309 and 2374 Hard Drive replacement. Escrito por: Andrew Bookholt ifixit CC BY-NC-SA es.ifixit.com Página 1 de 17 INTRODUCCIÓN
More information