Principal LED Qwik Stik Fluorescent Bulb Replacements
|
|
- Gyles Richards
- 6 years ago
- Views:
Transcription
1 Principal LED Qwik Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician. To prevent death, injury or damage to property this product must be installed in accordance with the National Electric Code in the USA or Canadian Electrical Code (CSA22.1) in Canada. Save These Instructions Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. Prepare Electrical Wiring Electrical Requirements Limited to use in dry and damp locations. The grounding and bonding of the LED Driver shall be done in accordance with National Electric Code (NEC) Article 600. Follow all National Electric Codes (NEC) and local codes. These products are only suitable for connection to a circuit from a Class 2 power source. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. *This Class [A] RFLD complies with the Canadian standard ICES-003. This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications. Conforms to the following standards: Principal LED LLC Venture Drive San Angelo, TX info@p-led.com REV
2 Hardware Wire Wire Connectors Zip Ties Electrical Tape Wire Strippers Drill Screwdriver Drill bits Driver bits Tape Measure Multimeter Screws as required Components (PL-QSYY-XX-SS, PL-QSYY-XX-DS, PL-QSYY-XX-TS, PL-QSYY-XX-SH)* *YY: Length of Stik in inches; XX: Color Temperature (See Spec Sheets Attached), MW SS: Single-Sided, DS: Double-Sided, TS: Three Sided, SH: Shallow 360 (Four Sided) Class 2 Power Supply Specifications LED PS Model/ Cat Nos. Input Output per Circuit Max. Power Load PL-PS VAC - 240VAC / 1.2A 12VDC / 5A 60W PL U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL MU 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL PCM-U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL U 100VAC - 277VAC / 2.2A A 12VDC / 5A * 2 (Dual Output) 120W PL-QB1-MV60-S 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W PL-QB1-MV120-S 100VAC - 277VAC / 2.2A A 12VDC / 5A * 2 (Dual Output) 120W VLP U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W VLP MU 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W VLP U 100VAC - 277VAC / 2.2A A 12VDC / 5A * 2 (Dual Output) 120W VLP PCM-U 100VAC - 277VAC / 1.1A A 12VDC / 5A 60W
3 Fluorescent to LED Prior to installation, survey the site for information regarding power and accessibility inside and outside the building. Ensure that the branch circuit supplying the existing transformer or ballast will be within the voltage ratings of the new LED power supply, and have a current rating not exceeding 20A, or that permitted by applicable local, state, or country electrical codes (whichever is less). If removal of the existing lighting equipment (see Step 2) eliminates the disconnect switch, as required by applicable local, state, or country electrical codes; a new disconnect switch must be installed. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state, and country electrical codes. Make sure the removal of lighting equipment does not compromise the integrity of the sign body. Fill in all holes with the appropriate amount of rated sealant as needed (excluding weep holes). Lamp Ballast 1. Ensure no power is going to the sign and disconnect the existing power ballast and gain access to lighting fixtures in sign. Remove existing T12 HO fluorescent bulbs Inspect existing sockets and replace as needed. and ballast. 4. Install Principal LED Qwik Stiks into existing T12 sockets. Position stiks so that the LED s are facing the sign faces and continue replacing the T12 lamps. 5. If installing multiple LED drivers, keep them at least 2 apart end to end and 4 apart along the sides. Mount power supplies with screws for to ensure it s secure. Live Black to Black Neutral White to White Red (+) Red (+) Black (-) Black (-) to LEDs Primary AC wire to sign Green to Green Ground 6. Wire AC line to LED driver(s) in accordance with the applicable local, state, and country electrical codes. Connect black to black or brown, white to white or blue, and green to green. 7. On the secondary (12V) side of the power supply, connect the red wires (+) from the Qwik Stiks to the red wire (+) on the power supply using wire connectors and do the same for black wires (-). Do not place more Stiks on a power supply than is recommended by the Stik specifications.
4 Qwik Stik Single-Sided Recommended for deep cabinets. 18" 15.91" A PL-QS18-XX-SS 24" 21.91" A PL-QS24-XX-SS 30" 27.91" A PL-QS30-XX-SS 36" 33.91" A PL-QS36-XX-SS 42" 39.91" A PL-QS42-XX-SS 48" 45.91" 1, A PL-QS48-XX-SS 60" 57.91" 1, A PL-QS60-XX-SS 64" 61.91" 1, A PL-QS64-XX-SS 72" 69.91" 1, A PL-QS72-XX-SS 84" 81.91" 1, A PL-QS84-XX-SS 96" 93.91" 2, A PL-QS96-XX-SS 108" 105.9" 2, A PL-QS108-XX-SS 117" " 2, A PL-QS117-XX-SS 120" " 2, A PL-QS120-XX-SS Qwik Stik Double-Sided Recommended for deep cabinets. 18" 15.91" A PL-QS18-XX-DS 24" 21.91" A PL-QS24-XX-DS 30" 27.91" 1, A PL-QS30-XX-DS 36" 33.91" 1, A PL-QS36-XX-DS 42" 39.91" 1, A PL-QS42-XX-DS 48" 45.91" 2, A PL-QS48-XX-DS 60" 57.91" 2, A PL-QS60-XX-DS 64" 61.91" 2, A PL-QS64-XX-DS 72" 69.91" 3, A PL-QS72-XX-DS 84" 81.91" 3, A PL-QS84-XX-DS 96" 93.91" 4, A PL-QS96-XX-DS 108" 105.9" 4, A PL-QS108-XX-DS 117" " 4, A PL-QS117-XX-DS 120" " 5, A PL-QS120-XX-DS *XX = PW (6300K Pure White), MW (4300K Medium White), WW (3500K Warm White) Note: Maximum units per 20A branch circuit is derated to 80% full load. Do not load more than 10A total in series (daisy chained) from unit to unit. If the total number of Stiks exceeds 10A, split the load by splicing back to input power. See installation instructions for details. Troubleshooting Tips Make sure output wiring is connected correctly. Turn off power and check wiring polarity. If so, reverse wires and illuminate. Make sure LED driver has the correct input voltage (VAC). Make sure there is no exposed wiring that could cause a short circuit. Make sure wire is in electrical contact at the UL listed connector. If the maximum number of Stiks has exceeded the sign or luminaire the Stiks may blink or not turn on. Count the Stiks and confirm the number of Stiks is within the maximum number listed in spec sheets attached.
5 Qwik Stik Three-Sided Recommended for shallow cabinets. 18" 15.91" A PL-QS18-XX-TS 24" 21.91" A PL-QS24-XX-TS 30" 27.91" 1, A PL-QS30-XX-TS 36" 33.91" 1, A PL-QS36-XX-TS 42" 39.91" 1, A PL-QS42-XX-TS 48" 45.91" 1, A PL-QS48-XX-TS 60" 57.91" 2, A PL-QS60-XX-TS 64" 61.91" 2, A PL-QS64-XX-TS 72" 69.91" 2, A PL-QS72-XX-TS 84" 81.91" 2, A PL-QS84-XX-TS 96" 93.91" 3, A PL-QS96-XX-TS 108" 105.9" 3, A PL-QS108-XX-TS 117" " 4, A PL-QS117-XX-TS 120" " 4, A PL-QS120-XX-TS Qwik Stik Shallow 360 Recommended for shallow cabinets. 18" 15.91" A PL-QS18-XX-SH 24" 21.91" A PL-QS24-XX-SH 30" 27.91" 1, A PL-QS30-XX-SH 36" 33.91" 1, A PL-QS36-XX-SH 42" 39.91" 1, A PL-QS42-XX-SH 48" 45.91" 2, A PL-QS48-XX-SH 60" 57.91" 2, A PL-QS60-XX-SH 64" 61.91" 2, A PL-QS64-XX-SH 72" 69.91" 3, A PL-QS72-XX-SH 84" 81.91" 3, A PL-QS84-XX-SH 96" 93.91" 4, A PL-QS96-XX-SH 108" 105.9" 5, A PL-QS108-XX-SH 117" " 5, A PL-QS117-XX-SH 120" " 5, A PL-QS120-XX-SH *XX = PW (6300K Pure White), MW (4300K Medium White), WW (3500K Warm White) Note: Maximum units per 20A branch circuit is derated to 80% full load. Do not load more than 10A total in series (daisy chained) from unit to unit. If the total number of Stiks exceeds 10A, split the load by splicing back to input power. See installation instructions for details. Troubleshooting Tips Make sure output wiring is connected correctly. Turn off power and check wiring polarity. If so, reverse wires and illuminate. Make sure LED driver has the correct input voltage (VAC). Make sure there is no exposed wiring that could cause a short circuit. Make sure wire is in electrical contact at the UL listed connector. If the maximum number of Stiks has exceeded the sign or luminaire the Stiks may blink or not turn on. Count the Stiks and confirm the number of Stiks is within the maximum number listed in spec sheets attached.
Principal LED Street Stik Fluorescent Bulb Replacements
Principal LED Street Stik Fluorescent Bulb Replacements LED Retrofit Guide (PL-RT1-001) WARNING Installation must only be performed by a licensed electrician. To prevent death, injury or damage to property
More informationWARNING. General Information
Principal LED Sign Retrofit Installation Manual Kit Model: PL RT1 001 WARNING Retrofit Installation must only be performed by qualified personnel in accordance with the National Electric Code in the USA
More informationPEREGRINE SERIES RETROFIT INSTALLATION GUIDE
06.05.17 HanleyLED H100W-PPS524V Spec Sheet SOLUTIONS THAT MAKE SENSE PEREGRINE SERIES RETROFIT INSTALLATION GUIDE Light Up New Markets Your Local Distributor: Grimco US www.grimco.com 800.542.9941 Canada
More informationBoxLED DS Plus (Double Side) BX-DS-PL; BX12BA-W4F Signage Lighting System INSTALLATION GUIDE
www.osram-americas.com/signage BoxLED DS Plus (Double Side) BX-DS-PL; BX12BA-W4F Signage Lighting System INSTALLATION GUIDE WARNING: ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION TO AVOID ELECTRICAL
More informationOSRAM ReliaSys TM D15 LED Retrofit Kit INSTALLATION GUIDE
www.osram-americas.com S90655 OSRAM ReliaSys TM D15 LED Retrofit Kit INSTALLATION GUIDE OSRAM ReliaSys TM Outdoor LED Retrofit Kit is an alternative to high-intensity discharge (HID) lamps up to 400W (MH)
More informationHomePro ZRF113. Z-Wave Radio Frequency (RF) Controlled, 120 VAC, Isolated Contact Fixture Module, Series 200, Release 2.2
RF Home Automation ZRF113 Z-Wave Radio Frequency (RF) Controlled, 120 VAC, Isolated Contact Fixture Module, Series 200, Release 2.2 Note: This module must be Included in the Network only where it will
More informationCHANNEL LETTER LIGHTING UNIQUE LIGHTING SOLUTIONS RETROFIT INSTALLATION GUIDE
UNIQUE LIGHTING SOLUTIONS LIGHTING WARNING -Installation must only be performed by a licensed electrician. -To prevent death, injury or damage to property this product must be installed in accordance to
More information3-Phase, Dual-Input 6-Slot Power Supply System STARTUP GUIDE
3-Phase, Dual-Input 6-Slot Power Supply System STARTUP GUIDE -ST-01 Page 1 of 10 November 2016 2016 Copyright Lite-On Technology Corporation ALL RIGHTS RESERVED. Lite-On is a trademark of Lite-On Technology
More informationAcquiSuite Ally 12 & 48 Advanced Multi-Circuit Meter
AcquiSuite Ally 12 & 48 Advanced Multi-Circuit Meter Install Guide Revision C (12/18) DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Revision C (12/18) Turn off all power supplying equipment
More informationUser Guide CPSMP VAC Power Supply Module: PointSystem CPSMC Accessory CPSMC Accessory. Contents.
User Guide CPSMP-205 110 240 VAC Power Supply Module: PointSystem CPSMC1800-200 Accessory CPSMC1900-100 Accessory Contents Contents...1 Description...1 Cautions and Warnings...2 Definitions...2 Power supply
More informationDual Relay Luminaire Control Module Wiring and installation manual Light is OSRAM
www.osram.us/extend Dual Relay Luminaire Control Module Wiring and installation manual Light is OSRAM Overview The Dual Relay Luminaire Control Module interfaces between the ENCELIUM EXTEND Networked Light
More informationAnswer Modular Power. Page 1 of Rev V. Power Kits. Change of Height Harness. Receptical Covers
Answer Modular Power Change of Height Harness Power Kits Receptical Covers NOTE: Unused modular electrical connector openings are not required to be capped. NOTE: The electrician can cut conduit and wire
More informationBefore you get started
Installation Guide Before you get started If you ve installed light switches before and are comfortable with high voltage wiring, installing a Noon switch is easy. If not, we highly recommend hiring a
More informationSignBOX II. Retrofit Guide for (X)WS201 and (X)WD201
Scope: This procedure is designed to aid in the installation of SloanLED s SignBOX II illumination product and power supply products. Skilled tradespeople familiar with general construction, electrical
More informationENCELIUM EXTEND Manager Wiring and installation manual Light is OSRAM
www.osram.us/extend ENCELIUM EXTEND Manager Wiring and installation manual Light is OSRAM Overview The ENCELIUM EXTEND Manager is a gateway that interfaces to both IT equipment (servers, LAN, etc) and
More informationENERCEPT H8035/H8036 DANGER NOTICE CAUTION. Networked Power Transducer (Modbus RTU) INSTALLATION GUIDE QUICK INSTALL TABLE OF CONTENTS
POWER MONITORING ENERCEPT Networked Power Transducer (Modbus RTU) DANGER US Patent No. 6,373,238 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Follow safe electrical work practices. See NFPA 70E in
More informationHandset Charging Rack OpenStage WL 3 / OpenStage WL3 Plus. Installation Guide A31003-M2000-J
Handset Charging Rack OpenStage WL 3 / OpenStage WL3 Plus Installation Guide A31003-M2000-J102-2-7631 Our Quality and Environmental Management Systems are implemented according to the requirements of the
More informationLinearray PD Retrofit Kit
Linearray Retrofit and Installation Instructions 1. Scope All Installations should be performed by qualified personnel and all electrical work should be performed in accordance to NEC and local code. These
More informationModified Sinewave Series. Power Inverter 1000/1500 MW 1210, MW1215. True Sinewave Power Inverter 1000/2000 SW 1210, SW 1220.
Modified Sinewave Power Inverter 1000/1500 MW 1210, MW1215 True Sinewave Power Inverter 1000/2000 SW 1210, SW 1220 Owner s Manual Modified Sinewave Series True Sinewave Series 1. INTRODUCTION Thank you
More informationETC Installation Guide
Unison Foundry Overview The Unison Foundry provides fully-rated 20A relays for switched power control with 0 10V dimming for compatible fluorescent ballasts and LED drivers. The provides two outputs of
More information4100/ VDC Converter Installation Instructions
4100/4120-0156 8 VDC Converter Installation Instructions Introduction This publication describes the installation procedure for the 8 VDC Converter. Related Documentation Field Wiring Diagram for 4100
More informationWireless Fixture Adapter (WFA100-SN) Installation Instructions
Installation Instructions The Daintree Wireless Fiture Adapter () forms part of Daintree s Controlscope Manager (CSM) in commercial and industrial buildings. It transmits and receives messages over the
More informationBluetooth Enabled Access Control MODEL BG-FE. Operating Instructions
BlueGuard FE Bluetooth Enabled Access Control MODEL BG-FE Operating Instructions CAUTION AND SAFETY INFORMATION IMPORTANT: If the equipment is used in a manner not specified in this manual, the protection
More informationPV Rapid Shutdown device
PV Rapid Shutdown device Installation and Operation Manual Solis-RSD-1G(1:1) Solis-RSD-1G(2:2) Manufacturer: Ginlong (Ningbo) Technologies Co.,Ltd., Ningbo, Zhejiang, P.R.China US Office: 565 Metro Pl.
More informationRack Input Module Installation Instructions
Rack Input Module Installation Instructions DOC. #560105000 A 7/30/04 PRINTED IN U.S.A. Regulatory Compliance Safety This device has been tested and found to be in compliance with the requirements set
More informationMC 11 EB-2 Power supply cabinet with external bus, AC version
MC 11 EB-2 Power supply cabinet with external bus, AC version USER/MAINTENANCE MANUAL 1 SLOT 0 SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 5 SLOT 6 SLOT 7 SLOT 8 SLOT 9 SLOT 10 SLOT 11 EB-2 (a) MC11 (b) (c) Figures
More informationSatellite INSTALLATION GUIDE
N3 Satellite INSTALLATION GUIDE ! WARNING! Shock Hazard. May result in serious injury or death. Turn power OFF at circuit breaker or remove fuse. Damage to this product caused by wiring with power on voids
More informationUSB 3.1 CAT6A/7 EXTENDER
USER MANUAL ICU504A USB 3.1 CAT6A/7 EXTENDER 24/7 AT OR VISIT BLACKBOX.COM Power Mode Config Status Link Video USB 2 USB 3 Power Mode Config Status Link Video USB 2 USB 3 TABLE OF CONTENTS PRODUCT OPERATION
More informationUser Manual. Smart Dimmer Switch. Part 1: General Specification Main Features... 2
1 User Manual Smart Dimmer Switch Contents Part 1: General... 2 1.1. Specification... 2 1.2. Main Features... 2 Part 2: Installation and Wire Connection... 3 Part 3: Connect the Smart Dimmer Switch to
More informationInstruction Bulletin. Fiber Optic Switch Packs. SLSPSP101 and SLSPSP102 for use with Luminaires INTRODUCTION CONTENTS OF THE BOX
Instruction Bulletin 63249-500-04A3 07/2010 Fiber Optic Switch Packs SLSPSP101 and SLSPSP102 for use with Luminaires INTRODUCTION SLSPSP101 Single Input Switch Pack SLSPSP102 Dual Input Switch Pack The
More informationPlease read this safety information carefully and keep this user manual for later reference.
Please read this safety information carefully and keep this user manual for later reference. This LED bulb is for indoor use only. Please disconnect this bulb from bulb holder before cleaning. Don t use
More informationSCROLL GAS PRICE DISPLAY SYSTEM ROS SERIES INSTALLATION MANUAL REV 3.0
SCROLL GAS PRICE DISPLAY SYSTEM ROS SERIES INSTALLATION MANUAL REV 3.0 Fax: (514) 683-0068 Rev : 3.0 www.novyc.com Page 1 of 11 WARNING The ROS Scroll Display System must be installed as per Novyc International's
More informationSAFETY WARNINGS AND GUIDELINES
1 SAFETY WARNINGS AND GUIDELINES Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the
More informationINSTRUCTION MANUAL DISTRIBUTION UNIT. Please read this manual thoroughly before use, and keep it handy for future reference.
INSTRUCTION MANUAL DISTRIBUTION UNIT Please read this manual thoroughly before use, and keep it handy for future reference. ISSUE 1 May 2006 LIMITATION OF LIABILITY THE INFORMATION IN THIS PUBLICATION
More informationMONOPRICE. Blackbird 4K HDMI 1x8 Splitter/Extender. User's Manual P/N 18787
MONOPRICE Blackbird 4K HDMI 1x8 Splitter/Extender P/N 18787 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS... 5 PRODUCT
More informationIntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide
IntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide *619751* P/N 619751 - Rev B IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS
More informationHi-lume Premier 0.1% EcoSystem LED Driver
Hi-lume Premier 0.1% EcoSystem LED Driver s provide a high performance solution for any space, in any application. They provide smooth, continuous dimming down to 0.1% of full output current, and fade
More informationEM-15 / EM-20 Energy Management Switch
Installation & Operator s Manual EM-15 / EM-20 Energy Management Switch WF-9900 Series Distributed in the U.S.A. and Canada by ARTERRA DISTRIBUTION Phone (877) 294-8997 Warranty: warranty@wfcoelectronics.com
More informationUSB Raven Port USB 3.1, 100m CAT 6a/7 Point-to-Point Extender System User Guide
USB 3-2-1 Raven 3104 4-Port USB 3.1, 100m CAT 6a/7 Point-to-Point Extender System User Guide Thank you for purchasing the USB 3-2-1 Raven 3104. Please read this guide thoroughly. This document applies
More informationUSER GUIDE. AXIS T8120 Midspan 15 W 1-port ENGLISH
USER GUIDE AXIS T8120 Midspan 15 W 1-port ENGLISH Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before
More informationCU USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date:
CU8860-0000 USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date: 2006-02-20 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions
More informationNT1-220 Rack. Installation Instructions. Specifications. Contents of Shipping Box. Important Safety Instructions. NT1-220 Rack
The NT1-220 Rack is designed to be used in conjunction with Tone Commander NT1U-220TC ISDN Network Terminations. A maximum of twelve NT1 units can be used in each rack. NT1-220 Rack Installation Instructions
More informationOmnitron Systems Technology, Inc. 1. iconverter. 19-Module Managed Power Chassis User s Manual
Omnitron Systems Technology, Inc. 1 iconverter 19-Module Managed Power Chassis User s Manual 27 Mauchly, #201, Irvine, CA 92618 Phone: (949) 250-6510; Fax: (949) 250-6514 2 Omnitron Systems Technology,
More informationSee instructions to download and install the latest version of LinkBoxLON and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationColourChaser Touch. Installation Guide
ColourChaser Touch Installation Guide Dimensions C I S 110 29 72 Ø 4.5 56 85 I 2 3 4 100 77 ColourChaser Touch - Dimensions in mm Bracket - Dimensions in mm 2 Philips ColourChaser Touch Manual Content
More informationWa r n i n g-wa r n i n g-wa r n i n g
Installation Instructions of the Power Analyzer Wa r n i n g-wa r n i n g-wa r n i n g Read and understand this manual before connecting device. Death, fire or serious injury can occur from using equipment
More informationMONOPRICE. Blackbird 4K Pro 1x2 Ultra Slim HDMI Splitter. User's Manual P/N 21612
MONOPRICE Blackbird 4K Pro 1x2 Ultra Slim HDMI Splitter P/N 21612 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety
More informationIntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures)
IntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
More informationControlKeeper 4. General Information. Connecting Relay Loads. Installation Sheet. Getting Started. Power Supply Wiring. Mounting the Cabinet
General Information ControlKeeper 4 Installation Sheet Model# CK4-120NO- Model# CK4-277NO The ControlKeeper-4 model is shipped in one package and is configured with either a 120V or a 277V transformer.
More informationDTS 310. DIN Rail Mounted, Indoor Rated Revenue Grade Electrical Sub-meter. Page 1. Measurlogic MQ A
DTS 310 DIN Rail Mounted, Indoor Rated Revenue Grade Electrical Sub-meter Page 1 1 PRODUCT OVERVIEW... 3 1.1 SUPPLIED ITEMS... 3 1.2 DOCUMENT CONVENTIONS... 4 1.3 PRODUCT SPECIFICATION... 4 1.3.1 Current
More informationPRO-HC IRRIGATION CONTROLLER
PRO-HC IRRIGATION CONTROLLER Hydrawise Ready Quick Start Guide hunterindustries.com TABLE OF CONTENTS Installation 3 Connecting AC Power 5 Connecting Station Wires 7 Connecting Sensors or Flow Meters 8
More informationInstallation, Testing, and Operating Procedures 30 AMP PORTABLE AND PERMANENT SERIES GFCI SINGLE and MULTIPHASE
IMPORTANT! Please read all the information on this sheet. SAVE THESE INSTRUCTIONS! NOTICE BEFORE USING READ INSTRUCTIONS COMPLETELY. TO BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NATIONAL
More informationSafety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationFDS / FDS-R / FDS-PS
FDS / FDS-R / FDS-PS USER MANUAL For use with 120V 60Hz input. Output is 120V 60Hz at 5amps 600W MAX. switched. ETL LISTED Conforms to UL STD 1241 3091594 79-15167-00 REV. A www.fiberstars.com Page 1 of
More information1.3 Operating Conditions -40 F to 150 F (-40 C to 65 C) 0% to 90% Relative Humidity, non-condensing
The Keri NXT-6RK is a keypad reader typically used for card + PIN dual verification applications. It transmits keypad data in either 8-bit burst (default) or 26-bit Wiegand formats and can be used as a
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationATT2 Installation Guide for PQube 3
ATT2 Installation Guide for PQube 3 ATT2 Installation Manual Rev 0.2 Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.powersensorsltd.com Table of
More informationNature Power Inverters. Modified Sinewave 1000w/1500w True Sinewave 1000w/2000w. Owner s Manual
Nature Power Inverters Modified Sinewave 1000w/1500w True Sinewave 1000w/2000w Owner s Manual Modified Sinewave Series True Sinewave Series For safe and optimum performance, the Power Inverter must be
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationMONOPRICE. ShowPony 12-Watt LED Derby FX Light (RGBW) User's Manual P/N
MONOPRICE ShowPony 12-Watt LED Derby FX Light (RGBW) P/N 612900 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 FEATURES... 5 CUSTOMER SERVICE... 5 PACKAGE CONTENTS... 5 DIMENSIONS DIAGRAM...
More informationInstallation/User Manual
Installation/User Manual APsystems YC500-A Photovoltaic Grid-connected Inverter Version 4.1 8/15 APsystems 600 Ericksen Ave. NE Ste 200 Seattle, WA 98110 TEL: 844-666-7035 EMAIL: info@apsystems.com WEB:
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationNow with Picture Memory
Intrasonic Technology, Inc. Color Video Door Phone / Intercom Installer s Manual Model No.V304KIT-R Now with Picture Memory Please read this manual carefully before the products are installed.technical
More informationSuperBus 2000 Phone Interface/Voice Module Installation Instructions
SuperBus 2000 Module Installation Instructions Product summary The SuperBus 2000 (PIV) Module provides phone and voice functions for the Concord, Concord 4, and Concord Express (v4) panels. The PIV module
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationBroadband Automatic Disconnect Switch. User Manual
Reset/Test Primary/ Primary Broadband Automatic Disconnect Switch User Manual Local Power Remote Pwer Local 63V Fault Secondary Select Secondary 220V Normal 990-1929 09/2004 Introduction Introduction
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationWireless General Purpose Adapter (WGA100) Installation Instructions
(WGA100) Installation Instructions Daintree s WGA100 DT111 forms (Rev. part 12.8.17) of the Daintree ControlScope control solution for commercial and industrial buildings. It transmits and receives messages
More informationCU port USB 2.0 hub. Version: 1.1 Date:
CU8004-0000 4 port USB 2.0 hub Version: 1.1 Date: 2006-08-11 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions of delivery
More informationSafety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationCAUTION READ CAREFULLY
DOCKING DRAWER INSTALL MANUAL, 0230-00004 Rev 2 7/1/15 Applicable Models: 0290-00030, 0290-00031 JTech Solutions, Inc. 12893 Alcosta Blvd. Ste M San Ramon, CA 94583 www.jtechsolutions.us CAUTION READ CAREFULLY
More informationSySTIUM TECHNOLOGIES. Assembly Guide. Model 133i
Assembly Guide Model 133i Radio Frequency Interference Notice (USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules,
More informationZ-Wave enabled 3-Way 15 Amp In-Wall Switch User Manual For Model HA18WD
Z-Wave enabled 15 Amp In-Wall User Manual For Model Thank you for purchasing the Z-Wave Enabled 15 Amp In-Wall. Z-Wave products by Wayne- Dalton allow you to manage and control your home by remote control
More informationSAVE THESE INSTRUCTIONS
OUTDOOR HARDWIRE INSTALLATION INSTRUCTIONS Please read and save these instructions. Read carefully before using product. Protect yourself and others by observing all safety information, warnings and cautions.
More informationUSB 2.0 CAT5E/6/7 EXTENDER
USER MANUAL IC402A-R2 USB 2.0 CAT5E/6/7 EXTENDER 24/7 AT OR VISIT BLACKBOX.COM + + + + Mode Config Power Link Host Activity Power Link Host Activity TABLE OF CONTENTS PRODUCT OPERATION AND STORAGE... 3
More informationUSB Raven Port USB 3.1, 200m Multimode Fiber Point-to-Point Extender System User Guide
USB 3-2-1 Raven 3124 4-Port USB 3.1, 200m Multimode Fiber Point-to-Point Extender System User Guide Thank you for purchasing the USB 3-2-1 Raven 3124. Please read this guide thoroughly. This document applies
More informationStart Here. Features. Model DS108 Dual Speed Hub Installation Giude
Start Here The NETGEAR Model DS108 Dual Speed Hub is a network hub that enables users to mix and match 10 and 100 megabits per second (Mbps) devices on the same network. This capability eliminates the
More informationWireless Adapter (WA100-PM) i. Installation Instructions
i. Installation Instructions The Daintree WA100-PM Wireless Adapter forms part of the Daintree ControlScope wireless controls solution for smart commercial and industrial buildings. It transmits and receives
More informationQuickPanel View & QuickPanel Control
GE Fanuc Automation Operator Interface Products QuickPanel View & QuickPanel Control PCMCIA Adapter IC754PCMCIA001-A Hardware User s Guide, GFK-2368 June 2005 GFK-2368 PCMCIA Host Adapter GFL-002 Warnings,
More informationBCM2 Series Branch Circuit Monitors Quick Setup Guide
BCM2 Series Branch Circuit Monitors Quick Setup Guide Safety Information DANGER! HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Follow safe electrical work practices. See NFPA 70E in the USA, or applicable
More informationPowerLogic ION7300 Series
PowerLogic ION7300 Series Power and Energy Meter Advanced Field Retrofit Instructions August 2006 Danger This symbol indicates the presence of dangerous voltage within and outside the product enclosure
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More information- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV
OVERVIEW The STR9 ELV is a long run, low power, linear surface mount LED lighting system designed for exterior architectural lighting applications. This guide contains important information on planning
More informationTelephone Line Monitor USER GUIDE
Telephone Line Monitor USER GUIDE For Technical Assistance call the Manufacturers direct Ph 800 530 8645 8AM - 5PM West Coast Pacific Time NATCOMM USA LLC Responsible Supplier Code NC OPERATION Our Telephone
More informationChecker is the sensor. CheckMate is the software that runs on your PC. You use CheckMate to set up Checker mm mm 4.
Quick Reference About Checker Checker is the sensor. CheckMate is the software that runs on your PC. You use CheckMate to set up Checker. Minimum PC Requirements Microsoft Windows 2000 or Windows XP 400MHz
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationTHE CTB08D LIGHT CONTOLLER
THE CTB08D LIGHT CONTOLLER The CTB08D is a one of the components in the Hobbyist line of Light- O-Rama products. The CTB08D must be used in conjunction with the Light-O-Rama software package. This controller
More informationShoreTel IP Phone 655. Quick Install Guide & Warranty
ShoreTel IP Phone 655 Quick Install Guide & Warranty Document and Software Copyrights Copyright 1998-2012 by ShoreTel Inc., Sunnyvale, California, USA. All rights reserved. Printed in the United States
More informationrcc.1081 Installation Instructions
rcc.1081 Installation Instructions Table of Contents Introduction...1 Specifications...2 Mounting...3 Wiring...5 Wiring Method...7 BACnet Network Wiring...8 Setting BACnet Address...9 Setting the BACnet
More informationMAINTENANCE MANUAL. EDACS REDUNDANT POWER SUPPLY SYSTEM 350A1441P1 and P2 POWER MODULE CHASSIS 350A1441P3, P4, AND P5 POWER MODULES TABLE OF CONTENTS
MAINTENANCE MANUAL EDACS REDUNDANT POWER SUPPLY SYSTEM 350A1441P1 and P2 POWER MODULE CHASSIS 350A1441P3, P4, AND P5 POWER MODULES TABLE OF CONTENTS SPECIFICATIONS*... 2 INTRODUCTION... 3 DESCRIPTION...
More informationMulti-Messager USB by Nel-Tech Labs, Inc. Installation & User Manual
Multi-Messager USB by Nel-Tech Labs, Inc. Installation & User Manual Index: Introduction... 3 Multi-Messager USB Layout Summary... 4-5 Installation... 6-9 Message Programming & Operation... 10 Warranty
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More information888385_01 Install.book Page 1 Wednesday, November 11, :45 PM. SMDR6 Installation Guide
888385_01 Install.book Page 1 Wednesday, November 11, 1998 2:45 PM SMDR6 Installation Guide 888385_01 Install.book Page 2 Wednesday, November 11, 1998 2:45 PM 888385_01 Install.book Page i Wednesday, November
More informationSync Control. Installation/Operation Manual Rev. E
9 315 Sync Control Installation/Operation Manual 164201140 Rev. E ------------------------------------------------------------------------ ------------------------------------------------------------------------
More informationUser s Manual. LumiVision series. A Designer s X-ray film illuminator. Walnut, CA U.S.A. By LCD TV Technology
User s Manual A Designer s X-ray film illuminator By LCD TV Technology series Point A Technologies, Inc. Walnut, CA U.S.A. FCC RF INTERFERENCE STATEMENT NOTE: This equipment has been tested and found to
More informationM215 (M215-60) Safety
M215 QUICK INSTALL GUIDE M215 (M215-60) Safety Important Safety Information This document contains important instructions to use during installation and maintenance of the Enphase M215 Microinverter. To
More informationOperating instructions only for authorized, skilled electricians with EIB training
73-1 - 6122 25054 ABB i-bus EIB 1-fold Switching Actuator/Sensor 6110 U-500 GJB 000 6151 A0162 flush-mounted Operating instructions only for authorized, skilled electricians with EIB training Contents
More informationPriva Blue ID Digital input module DI4/DI8/DI16
Priva Blue ID Digital input module Modular design An Priva Blue ID DI4 Digital input module, Priva Blue ID DI8 Digital input module or Priva Blue ID DI16 Digital input module are used to take status and
More informationInstalling and Configuring Rialto Analytic Appliances
Installing and Configuring Rialto Analytic Appliances Important Safety Information This manual provides installation and operation information and precautions for the use of this camera. Incorrect installation
More information