SMARTSTART MOTOR STARTERS

Transcription

1 SMARTSTART MOTOR STARTERS MCG 1

2 AT A GLANCE Covers all line voltages from V AC, single or three phase Transformer supplies a 24V AC coil voltage, no matter the line voltage 12V AC/DC - 250V AC/DC still accepted for outside control signal Wide overload range: 1-40A (up to 30HP at 480V AC line voltage) 2 Standard start/stop and remote (HOA) Pilot lights included True line-in and load-out installation Easy integration of remote and automation components Life-time technical support MCG 400 NW. ENTERPRISE DR. (2ND FLOOR), PORT SAINT LUCIE, FL

3 MCG SMARTSTART INDUSTRIAL STARTERS One starter. One part number. One solution. All-inclusive starter that reduces inventory by eliminating the need to purchase loose components. SMARTSTART Control Module integrates wide range overload, up to 600V AC voltage input, keypad, and automation I/O WHAT IS SMARTSTART? The patented SMARTSTART control module is an integrated, seamless solution that incorporates operator control, superior motor protection, and automation system compatibility in a rugged, compact unit. It offers a wide-range overload and an extensive array of automation and control features that vary between models. Some of these features include emergency shutdown, damper or valve control, status (proof of flow), fault and shutdown, and more. The SMARTSTART module also accepts an incoming voltage range from V AC. This is true plug and play; no changing transformers, no messing with terminal blocks. HOW DOES SMARTSTART WORK? SMARTSTART takes an active role in protecting your motor by measuring the motor inrush current and using it to gauge a safe operating range for your motor. In this way it intelligently detects if your motor overload isn t set correctly, protects against locked rotor, cycle fault, stall conditions, and more. The unique functionality of SMARTSTART saves time, labor, and stocking units. It also provides superior motor protection. This is why some of the top manufacturers in America trust SMARTSTART to protect and control their motors. MCG 3

4 SMARTSTART FEATURES RELIABLE AND COST-EFFECTIVE INSTALLATION Power failure reset options Direct V AC connection SmartStart 1-40A electronic protection Automation compatible Integrated keypad with remote Fully compatible with most automation systems Dry inputs - remote run, two external pilot devices, and limit switch input Wet inputs (12-250V AC) - remote run, shutdown Relay output - fault, proof of flow 24V DC output - power actuator Motor Inrush 6-10x FLA Current (amps) Locked Rotor Trip Stall Trip Max Time to Start Trip Wide range of programmable failure modes Pre-select behavior after power failure - restart last mode (no delay), restart with 10 second delay, and restart off FLA Standard Start Curve Start Time (seconds) Locked Rotor Current Motor Never Reaches FLA Typical Motor Stall Current Standard Motor Starting Current 4 MCG 400 NW. ENTERPRISE DR. (2ND FLOOR), PORT SAINT LUCIE, FL

5 INDUSTRIAL START/STOP WITH SMARTSTART MOTOR PROTECTION 30, 200~600V AC, 1-40A, AUTOMATION SYSTEM READY Easy integration into existing automation systems Comprehensive input/outputs for building management systems Reduced installation times Patent-pending motor protection Electronic protection including locked rotor, cycle fault, and maximum time to start FLA calibration indicators - ensures overload is correctly calculated Blackbox fault logging Records last 10 start conditions, including FLA setting, max inrush, run current, time to start, and safety start mode Retrievable in factory Included disconnect* Motor circuit protection disconnect provides short-circuit protection No fuses required Proactive alarms Alarms proactively react to preserve motor when operating out-of-range or during failed start-ups Active monitoring Active current monitoring trips faster than standard inverse trip curves, resulting in superior protection against locked rotor and stall conditions UL type 1, 4, and 3R enclosures Lockable enclosures 3R includes lockable keypad cover *Only for Combination version NEMA Sized MCG 5

6 SPECIFICATIONS Starter Type MCG - Industrial Start/Stop with SMARTSTART Across the line or Full Voltage Non-Reversing NEMA 1, 3R, OR 4 enclosed Voltage range: 3Ø, V AC Amperage range: 1-40A User Interface Start/Stop/Remote keypad with mode LEDs (N1 & 3R), Start/Stop/Remote switch & Run Pilot light (N4) Standard Control Operations Inputs Outputs Operational Environmental V Remote Apply V AC/DC to energize Dry Remote Shutdown Limit Switch Internal Pilot Device External Pilot Device Proof of flow current status Starter Fault Damper/Actuator Power fail modes N.O. Dry Contact Apply V AC/DC to energize N.O. Dry Contact N.O. Dry Contact (N1 & 3R only) N.O. Dry Contact (N1 & 3R only) N.O. Relay Contact Ratings: 110V DC, 0.3A Resistive, 125V DC, 0.5A GP 30V DC, 2.0A Resistive 120V AC 50/60Hz, 0.5A Resistive 125V AC 50/60Hz, 1.0A GP 240V AC 50/60Hz, 0.25A Resistive 24 V DC, 1A maximum Restart last mode, no delay (default) Restart with 10 second delay Restart Off - LED flashes last mode Ambient Operating Temp -5 to 140 F (-20 to 60 C) Ambient Storage Temp -5 to 185 F (-20 to 85 C) Relative Humidity 5% to 95% non-condensing (Nema 1) Motor Protection Adjustment / Description Default Setting Overload Current Setting Range 1-40A Per FLA Overload Trip Class Adjustable: Class 10 or 20, Trip current = 115% of FLA setting Class 10 Cycle Fault Trip if cycle rate exceeds 20 starts/minute Always On Stall Trips within 0.5 seconds (disabled during startup) Always On Smartstart Protection Adjustment / Description Default Setting Current Phase Unbalance Locked Rotor Out of Calibration On/Off Trips within 3 25% current unbalance. *Trip threshold changes to 80% unbalance when switched to Off Trips within 0.5 seconds Trips after 10 seconds if the FLA dial setting is incorrect (set above calculated FLA range), ie. Start current is outside of an acceptable range (fla setting * 5 < inrush < fla setting * 14). On Max Time to Start Regardless of FLA or I2t curve, always trip at start if starting current is outside of an acceptable range (inrush / 5) and still decreasing after 10 seconds. 6 MCG 400 NW. ENTERPRISE DR. (2ND FLOOR), PORT SAINT LUCIE, FL

7 UL TYPE 1 INDOOR ENCLOSURE STANDARD MOTOR STARTER - 3 PHASE, 200~600 V AC Three Phase HP Contactor 200V 230V 460V 600V NEMA Size Part Number MCG1-9/P MCG1-18/P MCG1-32/P P MCG1-40/P40 UL TYPE 1 INDOOR ENCLOSURE COMBINATION MOTOR STARTER - 3 PHASE, 200~600 V AC Three Phase HP Contactor NEMA Part Number 200V 230V 460V 600V Size 3/4 3/4 MCG1-9/P-G /2 1/ MCG1-9/P-G /4 3/ MCG1-9/P-G MCG1-9/P-G MCG1-9/P-G MCG1-18/P-G MCG1-18/P-G MCG1-18/P-G MCG1-32/P-G MCG1-32/P-G MCG1-32/P-G P MCG1-40/P-G40-40 UL TYPE 3R OUTDOOR ENCLOSURE STANDARD MOTOR STARTER - 3 PHASE, 200~600 V AC Three Phase HP Contactor NEMA Part Number 200V 230V 460V 600V Size MCG3R-9/P MCG3R-18/P MCG3R-32/P P MCG3R-40/P-40 UL TYPE 3R OUTDOOR ENCLOSURE COMBINATION MOTOR STARTER - 3 PHASE, 200~600 V AC Three Phase HP Contactor NEMA Part Number 200V 230V 460V 600V Size 3/4 3/4 MCG3R-9/P-G /2 1/ MCG3R-9/P-G /4 3/ MCG3R-9/P-G MCG3R-9/P-G MCG3R-9/P-G MCG3R-18/P-G MCG3R-18/P-G MCG3R-18/P-G MCG3R-32/P-G MCG3R-32/P-G MCG3R-32/P-G P MCG3R-40/P-G40-40 UL TYPE 4 INDOOR/OUTDOOR ENCLOSURE STANDARD MOTOR STARTER - 3 PHASE, 200~600 V AC Three Phase HP Contactor NEMxA Part Number 200V 230V 460V 600V Size MCG4-9/P MCG4-18/P MCG4-32/P P MCG4-40/P40 *Consult factory for NEMA 4X enclosure options MCG1-18/P-G17-40 Diconnect Amperage Overload Rating Contactor Size (9, 18, 32, etc.) Enclosure Rating (Type 1, 3R or 4) UL TYPE 4 OUTDOOR ENCLOSURE COMBINATION MOTOR STARTER - 3 PHASE, 200~600 V AC Three Phase HP 200V 230V 460V 600V 3/4 3/4 Contactor NEMA Size Part Number MCG4-9/P-G /2 1/ MCG4-9/P-G /4 3/4 2 3 MCG4-9/P-G MCG4-9/P-G MCG4-18/P-G MCG4-18/P-G MCG4-18/P-G MCG4-18/P-G MCG4-32/P-G MCG4-32/P-G MCG4-32/P-G P MCG4-40/P-G40-40 MCG 7

8 MCG (1/3R) WIRING SCHEMATICS ISS(1/3R) CONTROL WIRING Remote Run Voltage Inputs Shut Down VAC/DC Input VAC/DC Input ISS STARTER POWER WIRING FLA (A) Overload Setting Relay Outputs Status Common Fault OL Keypad PCB Power Pilot Devices Dry Input Actuator Control Contactor Coil Start Remote Remote Run Motor Limit Switch A1 A2 Normally Closed Input Normally Open Input Normally Open Input 24VDC, 1A Output Normally Open Input M 24V Output to contactor coil MCP (Optional) H1 H VAC Input L1 L2 L3 M T1 T2 T3 AUX CONT MTR H1 H4 3PH UL TYPE 1 DIMENSIONS All dimensions are in inches 7 5/8 13 9/ /8 6 3/8 8 1/16 UL TYPE 3R DIMENSIONS All dimensions are in inches 7 5/8 13 9/ /8 6 3/8 8 1/16 8 MCG 400 NW. ENTERPRISE DR. (2ND FLOOR), PORT SAINT LUCIE, FL

9 MCG4 WIRING SCHEMATICS ISS4 CONTROL WIRING POWER WIRING Remote Run Voltage Inputs Shut Down VAC/DC Input VAC/DC Input FLA (A) Keypad PCB Power Overload Setting Relay Outputs Pilot Devices Dry Input Actuator Control Contactor Coil Start Remote Remote Run Motor Limit Switch A1 A2 Status Common Fault STOP START REMOTE G Normally Open Input Normally Open Input M X A+ A- 24V Output to contactor coil X 24VDC, 1A Output MCP (Optional) OL H VAC Input L1 H4 L2 L3 M T1 T2 T3 AUX CONT MTR 3PH H1 H4 UL TYPE 4 DIMENSIONS All dimensions are in inches NON-COMBINATION* 10 7/16 7 MTG. 12 5/16 11 MTG. COMBINATION* 6 11/16 7 5/8 6 11/16 8 3/8 *Consult factory for NEMA 4X enclosure options *Combination dimensions are the same as non-combination dimensions except for the depth (shown above, 8 5/8 ). MCG 9

10 MCG offers a wide variety of industrial control and automation products as well as custom-built lighting contactors, enclosures, and motor starters. Flexibility allows MCG to create custom solutions for virtually any application. 10 MCG 400 NW. ENTERPRISE DR. (2ND FLOOR), PORT SAINT LUCIE, FL

11 MCG 11

12 400 NW. ENTERPRISE DR. (2ND FLOOR) PORT SAINT LUCIE, FL MCG 400 NW. ENTERPRISE DR. (2ND FLOOR), PORT SAINT LUCIE, FL A DIVISION OF