Installation and Operating instructions for Built-in Industrial PC C6525

Size: px
Start display at page:

Download "Installation and Operating instructions for Built-in Industrial PC C6525"

Transcription

1 Installation and Operating instructions for Built-in Industrial PC C6525 Version: 1.0 Date:

2

3 Table of contents Table of contents General Notes 3 Notes on the Documentation 3 Liability Conditions 3 Description of safety symbols 3 Basic safety measures 4 Operator s obligation to exercise diligence 5 Operator requirements 5 Product Description 6 Appropriate Use 6 Access to the Hard Disk, the CF-Slot and the Battery 6 Interfaces 7 Serial interface 7 DVI (Digital Visual Interface) 7 USB-Interfaces 7 Network connection 7 Power Supply 7 Additional plug-in cards (optional) 7 Ground connection 7 Installation Instructions 8 Transport and Unpacking 8 Transport 8 Unpacking 8 Installation of the PC in the control cabinet 9 Earthing measures 9 Mounting of the Industrial PC 10 Power Supply Connection 11 Beckhoff power supply technology 11 Pin assignment of the connector 12 Fitting the cable 13 Material for assembling the connectors 13 Assembling the connectors 13 Connecting Power Supply 14 Cable Cross Sections 14 Configuration for shutting down the PC 14 PC_ON and Power Status functions 14 UPS output 14 UPS output function 14 Wiring diagram 15 Connecting devices 16 Connecting cables 16 Check voltage rating and connect 16 Fastening the cables 16 Operating Instructions 17 Switching the Industrial PC on and off First switching on and driver installation Maintenance 18 Cleaning the Industrial PC 18 Replacing the battery on the motherboard 18 Servicing 18 Shutting down Disposal UPS Software Components (optional) 19 Installation on the PC 19 Help files

4 Table of contents Troubleshooting 20 Fault correction 20 Beckhoff Support & Service 21 Beckhoff branches and partner companies 21 Beckhoff Headquarters 21 Beckhoff Support 21 Beckhoff Service 21 Assembly dimensions 22 Appendix 23 Technical data 23 Approvals 23 FCC: Federal Communications Commission Radio Frequency Interference Statement FCC: Canadian Notice

5 General Notes General Notes Notes on the Documentation This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards. It is essential that the following notes and explanations are followed when installing and commissioning these components. Liability Conditions The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards. The documentation has been prepared with care. The products described are, however, constantly under development. For that reason the documentation is not in every case checked for consistency with performance data, standards or other characteristics. None of the statements of this manual represents a guarantee (Garantie) in the meaning of 443 BGB of the German Civil Code or a statement about the contractually expected fitness for a particular purpose in the meaning of 434 par. 1 sentence 1 BGB. In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation. This documentation is copyrighted. Any reproduction or third party use of this publication, whether in whole or in part, without the written permission of Beckhoff Automation GmbH, is forbidden. Description of safety symbols The following safety symbols are used in this operating manual. They are intended to alert the reader to the associated safety instructions. i Note Danger Warning This symbol is intended to highlight risks for the life or health of personnel. This symbol is intended to highlight risks for equipment, materials or the environment. This symbol indicates information that contributes to better understanding

6 General Notes Only switch the PC off after closing the software Basic safety measures Before the Industrial PC is switched off, software that is running must be properly closed. Otherwise it is possible that data on the hard disk is lost. Please read the section on Switching the Industrial PC on and off. Warning Switch off all parts of the equipment, then uncouple the fieldbus! Before opening the housing of the PC, and whenever the PC is being used for purposes other than plant control, such as during functional tests following repair, all parts of the equipment must first be switched off, after which the Industrial PC can be uncoupled from the plant. Pulling out the fieldbus connection plug uncouples the PC (optional). Items of equipment that have been switched off must be secured against being switched on again. The Industrial PC s power supply unit must be supplied with 24 V DC. Warning Do not exchange any parts when under power! When components are being fitted or removed, the supply voltage must be switched off. Fitting work on the Industrial PC can result in damage: If metal objects such as screws or tools fall onto operating circuit boards. If connecting cables internal to the PC are removed or inserted during operation. If plug-in cards are removed or inserted when the PC is switched on

7 General Notes Operator s obligation to exercise diligence The operator must ensure that the Industrial PC is only used for its intended use (see also Product Description chapter). the Industrial PC is in a sound condition and in working order during operation. the operation manual is in good condition and complete, and always available for reference at the location of the Industrial PC. the Industrial PC is operated, maintained and repaired only by sufficiently qualified and authorized personnel. the personnel is instructed regularly about relevant occupational safety and environmental protection aspects, and is familiar with the operating manual and in particular the safety notes contained herein. none of the safety and warning notes attached to the Industrial PC are removed, and that all notes remain legible. National regulations depending on the machine type Depending on the type of machine and plant in which the Industrial PC is being used, there will be national regulations for the control of such machines and plant that the operator must observe. These regulations cover, amongst other things, the intervals between inspections of the controller. The operator must initiate such inspections in good time. Warning Only trained persons may open the Industrial PC housing! The operator is responsible for ensuring that only trained electrical staff opens the housing of the Industrial PC. Procedure in the event of a fault Read the operating instructions Software knowledge In the event of a fault in the Industrial PC, appropriate measures can be determined with the aid of the list in the Fault correction section. Operator requirements Every user of the Industrial PC must have read these operating instructions. Every user must be familiar with any of the functions of the software installed on the PC that he can reach

8 Product Description Product Description View form the top Appropriate Use The 6525 Industrial PC is designed for mounting in control cabinets or in the rear panel of a control or console housing for machine and plant engineering applications. The heat sink of the IPC is thereby fed to the outside through a suitable cut-out in the panel of the control cabinet. This ensures that the power dissipation of the processor and chipset is given off directly to the surroundings. Configuration Removing the cover plate The 6525 is a fanless Industrial PC with passive cooling and can hence be constructed completely without rotating parts. Integrated seals provide for an IP 67 closure. Access to the Hard Disk, the CF-Slot and the Battery A 2½-inch SATA hard disk (optional), the CF-slot and the battery are located behind the cover plate on top of the Industrial PC. 1 2 Access to the hard disk, the CF-slot and the battery After loosening the two screws (1) and (2) the cover plate can be removed. 2½-inch SATA hard disk CF-slot battery

9 Product Description Interfaces Interfaces to the Industrial PC X102 X103 X106 X105 X108 X107 X109 X110 X111 RS 232 COM1 DVI-I USB1 USB4 Network 10/100BASE-T Network 10/100/1000BASE-T Power supply Serial interface The Industrial PC has one serial interfaces, COM1 (X102), using the type RS232, which is brought to a 9 pin SUB-D plug connector. DVI (Digital Visual Interface) The DVI connection (X103) is used for transferring the video signal. DVI-I standard is supported. USB-Interfaces The four USB interfaces (X105 X108) are used for connecting peripheral devices with USB connection. USB2.0 standard is supported. Network connection The RJ-45 connector (X109) allows the PC to be connected to a 10/100BASE-T Local Area Network (LAN). The RJ-45 connector (X110) allows the PC to be connected to a 10/100/1000BASE-T Local Area Network (LAN). Power Supply The power supply for the Industrial PC is established via the socket (X111). Type plate Additional plug-in cards (optional) There is a type plate on the top of the Industrial PC which provides information about the hardware configuration of the Industrial PC at the time it was supplied. Ground connection Ground connection stud bolt The Industrial PC is grounded via the stud bolt

10 Installation Instructions Installation Instructions Please also refer to chapter General Notes. Transport and Unpacking The specified storage conditions must be observed (see chapter Technical data). Transport Despite the robust design of the unit, the components are sensitive to strong vibrations and impacts. During transport, your Industrial PC should therefore be protected from excessive mechanical stress. Therefore, please use the original packaging. Warning Danger of damage to the unit! If the device is transported in cold weather or is exposed to extreme variations in temperature, make sure that moisture (condensation) does not form on or inside the device. Prior to operation, the unit must be allowed to slowly adjust to room temperature. Should condensation occur, a delay time of approximately 12 hours must be allowed before the unit is switched on. Unpacking Proceed as follows to unpack the unit: 1. Remove packaging. 2. Do not discard the original packaging. Keep it for future relocation. 3. Check the delivery for completeness by comparing it with your order. 4. Please keep the associated paperwork. It contains important information for handling the unit. 5. Check the contents for visible shipping damage. 6. If you notice any shipping damage or inconsistencies between the contents and your order, you should notify Beckhoff Service

11 Installation Instructions Installation of the PC in the control cabinet The 6525 Industrial PC is designed for mounting in control cabinets for machine and plant engineering applications. The ambient conditions specified for operation must be observed (see chapter Technical data). Preparation of the control cabinet The control cabinet must be provided with the relevant cutout (see chapter Assembly dimensions). i Note The clearance above and below the housing must be at least 200 mm in order to ensure adequate ventilation of the PC. Warning Extreme environmental conditions should be avoided as far as possible. Protect the PC from dust, moisture and heat. The ventilation slots of the PC must not be covered. Earthing measures Earthing measures Earthing connections dissipate interference from external power supply cables, signal cables or cables to peripheral equipment. Establish a low-impedance connection from the earthing point on the PC housing to the central earthing point on the control cabinet wall, in which the computer is being installed. The earthing connection is located beside the power supply connector of the Industrial PC (see chapter Ground connection)

12 Installation Instructions Mounting of the Industrial PC with clamping levers Mounting of the Industrial PC The Industrial PC is mounted with clamping levers. Clamping levers Release clamping levers, For installation the Industrial PC proceed as follows: Insert the Industrial PC into the cutout. Release the clamping levers with a No. 2.5 Allen key. folding them out Turn the clamping levers to the side through 90, and retighten them. and retighten the screws

13 Installation Instructions Supplied mains power unit i Note Danger Power Supply Connection The Industrial PC is fitted with a 24 V DC power supply unit. When the Industrial PC is provided with a power supply unit with integrated UPS (order option) you can realize an uninterruptible power supply (UPS) using the battery pack C9900-U330. Danger of Explosion if using other battery packs! Beckhoff power supply technology Schematic diagram of power supply unit wirings Innovative solution for shutting down Industrial PCs Industrial PCs equipped with a UPS are in actual use frequently switched off by simply turning off the supply voltage. In this case the PC shuts down via the battery. However, over time this reduces the service life of the battery. The new Beckhoff power supply technology approach addresses this problem and now offers the user the option of switching the PC off without the need for using the battery, thereby reducing the load on the battery. In addition to the main switch this innovative solution uses an ON/OFF switch for the machine. Basically, the main switch remains switched on and provides the power supply for the PC during shutdown. Once the PC has shut down, the PC power supply unit issues a signal to indicate that the process is complete and that the main voltage can be switched off. This can be done manually via a signal lamp connection or via a contactor. With this solution the main switch generally only has to be switched off if the control cabinet has to be opened

14 Installation Instructions In order to maintain a screen display for the Industrial PC in the event of a power failure, the power supply unit is equipped with a UPS output for connecting a Control Panel. This enables a power failure to be visualised and displayed to the user. Once the PC has shut down, the UPS output is switched off in order to avoid total discharge of the battery. For a detailed functional description please refer to section Connecting Power Supply. Pin assignment of the connector The power supply and the external circuit for switching the Industrial PC on and off are connected via the 8-pole plug connector. Pin assignment for connecting the switch, the power supply and the battery pack (optional) Pin Function 1 - Battery Pack 2 + (with UPS only) 3 UPS+ (Output) V DC 6 + Power Supply 7 PC_ON 8 Power-Status

15 Installation Instructions Fitting the cable Wiring in accordance with wiring diagram Fit the cables for the power supply of the Industrial PC, the connection of the battery pack as well as the connection of the power-switch in accordance with the wiring diagram, using the included material for assembling the connectors. Material for assembling the connectors Material for assembling the connectors Plug connector 8-pole, Strain relief housing with lacing cord Conductive cross-section Fitting the connector to the cable Assembling the connectors The connector is specified for 16 A and can lift conductive cross-sections until 1.5 mm 2. So the connector is fitted to the cable: 1. Strip insulation from the cable ends (Length of stripped conductor is 8 9 mm). 2. Screw together the cable ends in the 8-pole plug connector in accordance with wiring diagram. Applying the strain relief Thread the lacing cord into that lower part of the strain relief housing. Putting in the plug connector Put the plug connector into that lower part of the strain relief housing. Tighten the lacing cord and pinch off the plastic strap. Fixing the upper part of the strain relief housing Fix the upper part of the strain relief housing by snapping it onto the lower part

16 Installation Instructions Connecting Power Supply The external wiring consists of the connection of the power supply, the battery pack (optional) and the connection of customised components for shutting down the PC. Note cable cross sections, avoid voltage drop! Cable Cross Sections For the connection of the power supply, wiring with a cable-cross-section of 1.5 mm 2 must be used. With bigger distances between voltage source and PC, you take the voltage drop as a function of the cable-cross-section as well as voltage fluctuations of your distribution voltage into account, so that is secured that the voltage doesn't fall under 22 V at the power supply. Insert Fuse The power supply must be protected with maximum 16 A. Configuration for shutting down the PC The connections for shutting down the Industrial PCs are established via the PC_ON input and the Power Status output. PC_ON and Power Status functions If the PC_ON input is connected to 24 V via a switch, the PC shuts down according to the rules. The PC_ON signal is inverted, i.e. the PC shuts down if the 24 V connection is live. If the PC_ON input is NOT connected by the user, the PC can be booted in the familiar way by connecting the supply voltage and shut down via the battery by switching off the supply voltage. Warning This procedure significantly reduces the service life of the rechargeable battery and should therefore not be used. Once the PC has shut down, the Power Status output is switched from 24 V to 0 V. Via this output a signal lamp can be connected or a contactor for de-energising the whole system. The maximum load for the Power Status output is 0.5 A and a suitable fuse should be provided. UPS output In order to maintain a screen display for the PC in the event of a power failure, the power supply unit is equipped with a UPS output for connecting a Control Panel. The maximum load for the output is 2.0 A. UPS output function The 24 V DC connection at the UPS output is live even after a power failure. The maximum load is 2.0 A. Once the PC has been de-energised via the UPS software, the UPS output is switched to 0 V. Any connected panel is thus switched off, and total discharge of the rechargeable battery is prevented

17 Installation Instructions Wiring diagram Wiring diagram external switch and power supply Wiring according to the wiring diagram (the circuit of PC_ON and Power- Status is symbolical): i Note The battery pack can only be connected when the Industrial PC is provided with an integrated UPS (order option)

18 Installation Instructions Connecting devices Warning The power supply plug must be withdrawn! Please read the documentation for the external devices prior to connecting them. During thunderstorms, plug connector must neither be inserted nor removed. When disconnecting a plug connector, always handle it at the plug. Do not pull the cable! Connecting cables The connections are located at the top of the Industrial PC and are documented in the product description chapter. When connecting the cables to the Industrial PC, proceed according to the following sequence: Switch off all the devices that are to be connected. Disconnect all the devices that are to be connected from the power supply. Connect all the cables between the Industrial PC and to the devices that are to be connected. Connect all data transfer cables (if present) to the appropriate plug-in receptacles of the data/telecommunication networks. Reconnect all devices to the power supply. Check voltage rating and connect Fitted with the 24 V DC power supply unit: 1. Check that the external power supply is providing the correct voltage. 2. Insert the power supply cable that you have assembled into the Industrial PC's power supply socket. Then connect it to your external 24 V power supply. Warning If a 24 V UPS is installed, the same type of rechargeable battery must be used. Fastening the cables Fastening the cables The connecting cables of the Industrial PC can be fastened with lacing cords. Therefore the pictured clips are mounted at the housing (see arrow)

19 Operating Instructions Operating Instructions Please also refer to chapter General Notes. Switch on Shutting down and switching off Switching the Industrial PC on and off The Industrial PC does not have its own mains switch. The Industrial PC will start when the equipment is switched on, or when it is connected to the power supply. When the plant is switched off, or when it is disconnected from its power supply, the Industrial PC will be switched off. Control software such as is typically used on Industrial PCs permits various users to be given different rights. A user who may not close software may also not switch the Industrial PC off, since data can be lost from the hard disk by switching off while software is running. Warning Warning First shut down, then switch off the PC! If the Industrial PC is switched off as the software is writing a file to the hard disk, the file will be destroyed. Control software typically writes something to the hard disk every few seconds, so that the probability of causing damage by switching off while the software is running is very high. When you have shut down the Industrial PC, you have to switch off power supply for at least 10 seconds before rebooting the system. After resetting power supply the PC will start booting automatically. First switching on and driver installation When you switch on the Industrial PC for the first time, the pre-installed operating system (optional) will be started. In this case, all the required drivers for any additional, optional hardware components ordered with the PC will already have been installed. If the PC was ordered without operating system, you have to install the operating system and the driver software for any auxiliary hardware yourself. Please follow the instructions in the documentation for the operating system and the additional devices

20 Operating Instructions Maintenance Please also refer to chapter General Notes. Cleaning the Industrial PC Danger Switch off the Industrial PC and all connected devices, and disconnect the Industrial PC from the power supply. The Industrial PC can be cleaned with a soft, damp cloth. Do not use any aggressive cleaning materials, thinners, scouring material or hard objects that could cause scratches. Replacing the battery on the motherboard A used battery on the motherboard has to be replaced according to the rules of the board manufacturer. See also chapter Product Description. Danger Danger of Explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Servicing The Industrial PC requires no maintenance. Shutting down Dismantling the Industrial PC Observe national electronics scrap regulations Disposal The device must be fully dismantled in order to dispose of it. The housing can be sent for metal recycling. Electronic parts such as disk drives and circuit boards must be disposed of in accordance with national electronics scrap regulations

21 UPS Software Components (optional) UPS Software Components (optional) Installing the UPS driver software For operating the power supply unit as a UPS, the UPS driver software and the associated UPS driver must be installed on the Industrial PC. On delivery of the Beckhoff Industrial PC with operating system the software is already installed. Should the software not be installed on your PC, the drivers can be installed from the driver CD provided. Installation Installation on the PC To install the UPS driver software, execute file Beckhoff_UPS_vx.xx.xx.exe from the subdirectory of UPS\ from the CD provided on the Industrial PC (Driver-archive for the Industrial-PC, C9900-S700-xxxx). The program is self-extracting and will guide the user through the installation routine. Beckhoff Information System Help files The driver software comes with a detailed help function. The help files can be called up either directly from the configuration register by clicking the Help button, or under via Start > Programs > Beckhoff > UPS software components

22 Troubleshooting Troubleshooting Please also refer to chapter General Notes. Fault correction Fault Cause Procedure Nothing happens after the Industrial No power supply to the Industrial Check power supply cable. PC has been switched on PC. Other cause. Call Beckhoff Service. The Industrial PC does not boot fully Setup settings are incorrect. Other cause. Check the setup settings. Call Beckhoff Service. Computer boots, software starts, but control does not operate correctly Cause of the fault is either in the software or in parts of the plant outside the Industrial PC. Call the manufacturer of the machine or the software. The Industrial PC functions only partially or only part of the time, e.g. no or dark picture, but disk drive responds when switching on Defective components in the Industrial PC. Call Beckhoff Service

23 Troubleshooting Beckhoff Support & Service Beckhoff and their partners around the world offer comprehensive support and service, guaranteeing fast and competent assistance with all questions related to Beckhoff products and system solutions. Beckhoff branches and partner companies Please contact your Beckhoff branch office or partner company for local support and service on Beckhoff products! The contact addresses for your country can be found in the list of Beckhoff branches and partner companies: You will also find further documentation for Beckhoff components there. Beckhoff Headquarters Beckhoff Automation GmbH Eiserstraße Verl Germany Phone: +49(0)5246/963-0 Fax: +49(0)5246/ info@beckhoff.com Beckhoff Support Beckhoff offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with wideranging services: worldwide support design, programming and commissioning of complex automation systems training program for Beckhoff system components Hotline: +49(0)5246/ Fax: +49(0)5246/ support@beckhoff.com Beckhoff Service The Beckhoff service center supports you in all matters of after-sales service: on-site service repair service spare parts service hotline service Hotline: +49(0)5246/ Fax: +49(0)5246/ service@beckhoff.com Quote the project number If servicing is required, please quote the project number of your product

24 Assembly dimensions Assembly dimensions Warning Industrial PC C6525 The assembly of the unit must take place with the orientation diagrammed here. All dimensions are in mm. rear view side view top view

25 Appendix Appendix Technical data Industrial PC 6525 Dimensions (W x H x D): 330 x 275 x 82 mm Weight: 4.74 kg Do not use the PC in areas The Industrial PC may not be used in areas of explosive hazard. of explosive hazard The following conditions must be observed during operation: Environmental conditions Ambient temperature: Outside: 0 to 45 C Inside: 0 to 55 C Atmospheric humidity: Maximum 95%, non-condensing Shock resistance Sinusoidal vibration: (EN ) 10 to 58 Hz: mm 58 to 500 Hz: 0.5 G (~ 5 m/ s 2 ) Impact: (EN / -29) 5 G (~ 50 m/ s²), duration: 30 ms Protection class Protection class: Outside: IP65 Inside: IP20 Power supply Supply voltage: 22 30V V DC 24 V DC power pack Power consumption: approx. 90 W (basic configuration) When operated with UPS: additional 30 W (while charging) additional 44 W (with UPS-output) Electromagnetic Compatibility (EMC) Transport and storage FCC Approval for USA FCC Approval for Canada Interference resistance: according to EN Emitted resistance: according to EN The same values for atmospheric humidity and shock resistance are to be observed during transport and storage as in operation. The shock resistance during transport can be improved by means of suitably packing the Industrial PC. The ambient temperature during storage and transport must be between -20 C and +65 C. Approvals FCC: Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC: Canadian Notice This equipment does not exceed the Class A limits for radiated emissions as described in the Radio Interference Regulations of the Canadian Department of Communications

Installation and Operating instructions for Control Cabinet PCs C63xx

Installation and Operating instructions for Control Cabinet PCs C63xx Installation and Operating instructions for Control Cabinet PCs C63xx - 0020 Version: 1.4 Date: 2009-08-20 Table of contents Table of contents 1. 2. 3. 4. 5. General instructions 3 Notes on the Documentation

More information

C9900-P223 and C9900-P224

C9900-P223 and C9900-P224 Installation and Operating instructions for C9900-P223 and C9900-P224 Power Supply Units Version: 1.2 Date: 2012-02-22 Table of contents Table of contents 1. Foreword 2 Notes on the Documentation 2 Liability

More information

Installation and Operating instructions for Industrial PC series C61xx

Installation and Operating instructions for Industrial PC series C61xx Installation and Operating instructions for Industrial PC series C61xx Version: 2.2 Date: 2007-02-09 Table of contents Table of contents 1. 2. 3. 4. General instructions 3 Notes on the Documentation 3

More information

Installation and Operating instructions for Control Cabinet PC C6915

Installation and Operating instructions for Control Cabinet PC C6915 Installation and Operating instructions for Control Cabinet PC C6915 Version: 1.2 Date: 2010-09-22 Table of contents Table of contents 1. 2. 3. 4. Foreword 3 Notes on the Documentation 3 Liability Conditions

More information

Installation and Operating instructions for. Control Cabinet PC C6210. Version: 1.4 Date:

Installation and Operating instructions for. Control Cabinet PC C6210. Version: 1.4 Date: Installation and Operating instructions for Control Cabinet PC C6210 Version: 1.4 Date: 2016-12-12 Table of contents Table of contents 1. 2. 3. 4. 5. 6. 7. General instructions 3 Notes on the Documentation

More information

C9900-P208 and C9900-P209

C9900-P208 and C9900-P209 Installation and Operating instructions for C9900-P208 and C9900-P209 Power Supply Units Version: 1.5 Date: 2012-02-22 Table of contents Table of contents 1. Foreword 2 Notes on the Documentation 2 Liability

More information

Installation and Operating instructions for Industrial PC series C61xx from Version: 3.0 Date:

Installation and Operating instructions for Industrial PC series C61xx from Version: 3.0 Date: Installation and Operating instructions for Industrial PC series C61xx from -0060 Version: 3.0 Date: 2018-02-16 Table of contents Table of contents 1. 2. 3. 4. 5. General instructions 3 Notes on the Documentation

More information

Installation and Operating instructions for. Control Cabinet PC C6240 from Version: 2.0 Date:

Installation and Operating instructions for. Control Cabinet PC C6240 from Version: 2.0 Date: Installation and Operating instructions for Control Cabinet PC C6240 from -0060 Version: 2.0 Date: 2018-02-16 Table of contents Table of contents 1. 2. 3. 4. 5. 6. 7. General instructions 3 Notes on the

More information

Installation and Operating instructions for Industrial PC series C61xx up to Version: 2.6 Date:

Installation and Operating instructions for Industrial PC series C61xx up to Version: 2.6 Date: Installation and Operating instructions for Industrial PC series C61xx up to -0050 Version: 2.6 Date: 2018-02-16 Table of contents Table of contents 1. 2. 3. 4. General instructions 3 Notes on the Documentation

More information

Installation and Operating instructions for C / Fanless Control Cabinet Industrial PC. Version: 1.0 Date:

Installation and Operating instructions for C / Fanless Control Cabinet Industrial PC. Version: 1.0 Date: Installation and Operating instructions for C6925-0020/-0030 Fanless Control Cabinet Industrial PC Version: 1.0 Date: 2016-05-27 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation

More information

Installation and Operating instructions for. Control Cabinet PC C6250 up to Version: 1.6 Date:

Installation and Operating instructions for. Control Cabinet PC C6250 up to Version: 1.6 Date: Installation and Operating instructions for Control Cabinet PC C6250 up to -0060 Version: 1.6 Date: 2018-02-16 Table of contents Table of contents 1. 2. 3. 4. General instructions 3 Notes on the Documentation

More information

Installation and Operating instructions for. Built-in Control Panel CP6608. Version: 1.0 Date:

Installation and Operating instructions for. Built-in Control Panel CP6608. Version: 1.0 Date: Installation and Operating instructions for Built-in Control Panel CP6608 Version: 1.0 Date: 2008-02-07 General Notes Table of contents 1. 2. 3. 4. 5. 6. General Notes 2 Notes on the documentation 2 Liability

More information

Installation- and Operating instructions for CU Ethernet Controller with USB Input. Version: 1.4 Date:

Installation- and Operating instructions for CU Ethernet Controller with USB Input. Version: 1.4 Date: Installation- and Operating instructions for CU8880-0010 Ethernet Controller with USB Input Version: 1.4 Date: 2018-04-12 Table of contents Table of contents 1. 2. 3. 4. 5. General instructions 2 Notes

More information

Installation- and Operating instructions for. Build-in Industrial PCs C3620, C3640 from Version: 3.0 Date:

Installation- and Operating instructions for. Build-in Industrial PCs C3620, C3640 from Version: 3.0 Date: Installation- and Operating instructions for Build-in Industrial PCs C3620, C3640 from -0060 Version: 3.0 Date: 2018-02-16 Table of contents Table of contents 1. 2. 3. 4. 5. General instructions 3 Notes

More information

Installation- and Operating instructions for CU Port USB 2.0 Hub. Version: 1.3 Date:

Installation- and Operating instructions for CU Port USB 2.0 Hub. Version: 1.3 Date: Installation- and Operating instructions for CU8005-0000 4-Port USB 2.0 Hub Version: 1.3 Date: 2018-04-27 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation 3 1.1.1 Liability

More information

Installation- and Operating instructions for CU Port USB 3.0 Hub. Version: 1.1 Date:

Installation- and Operating instructions for CU Port USB 3.0 Hub. Version: 1.1 Date: Installation- and Operating instructions for CU8006-0000 4-Port USB 3.0 Hub Version: 1.1 Date: 2018-04-27 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation 3 1.1.1 Liability

More information

Installation and Operating instructions for C Ultra compact Industrial PC. Version: 1.3 Date:

Installation and Operating instructions for C Ultra compact Industrial PC. Version: 1.3 Date: Installation and Operating instructions for C6015-0010 Ultra compact Industrial PC Version: 1.3 Date: 2018-04-12 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation 3 1.1.1

More information

Installation and Operating instructions for 19 Inch Rack Mount Industrial PC C5102 from -0060

Installation and Operating instructions for 19 Inch Rack Mount Industrial PC C5102 from -0060 Installation and Operating instructions for 19 Inch Rack Mount Industrial PC C5102 from -0060 Version: 3.0 Date: 2018-02-16 Foreword Table of contents 1. 2. 3. 4. 5. Foreword 4 Notes on the Documentation

More information

Installation and Operating instructions for. Panel-PC CP71xx. Version: 1.4 Date:

Installation and Operating instructions for. Panel-PC CP71xx. Version: 1.4 Date: Installation and Operating instructions for Panel-PC CP71xx Version: 1.4 Date: 2007-11-08 Table of contents 1. 2. 3. 4. 5. Table of contents General Notes 3 Notes on the documentation 3 Liability conditions

More information

Installation and Operating instructions for. Control Cabinet Industrial PC C from Version: 2.0 Date:

Installation and Operating instructions for. Control Cabinet Industrial PC C from Version: 2.0 Date: Installation and Operating instructions for Control Cabinet Industrial PC C6240-1007 from -0060 Version: 2.0 Date: 2018-02-16 Table of contents Table of contents 1. 2. 3. 4. Foreword 3 Notes on the Documentation

More information

Installation and Operating instructions for. CP27xx. Fanless multi-touch built-in Panel PC. Version: 1.0 Date:

Installation and Operating instructions for. CP27xx. Fanless multi-touch built-in Panel PC. Version: 1.0 Date: Installation and Operating instructions for CP27xx Fanless multi-touch built-in Panel PC Version: 1.0 Date: 2015-09-25 Table of contents Table of contents 1 Foreword 4 1.1 Notes on the Documentation 4

More information

CU USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date:

CU USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date: CU8860-0000 USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date: 2006-02-20 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions

More information

Installation and Operating instructions for. Economy built-in Panel PC CP62x9. Version: 1.0 Date:

Installation and Operating instructions for. Economy built-in Panel PC CP62x9. Version: 1.0 Date: Installation and Operating instructions for Economy built-in Panel PC CP62x9 Version: 1.0 Date: 2010-03-29 Foreword Table of contents 1. 2. 3. 4. Foreword 3 Notes on the Documentation 3 Liability Conditions

More information

Installation and Operating instructions for. Built-in Panel PC CP63xx. Version: 1.4 Date:

Installation and Operating instructions for. Built-in Panel PC CP63xx. Version: 1.4 Date: Installation and Operating instructions for Built-in Panel PC CP63xx Version: 1.4 Date: 2007-11-26 Table of contents Table of contents 1. 2. 3. 4. General Notes 3 Notes on the Documentation 3 Liability

More information

Control Cabinet Industrial PC C6640/ C6650 up to -0030

Control Cabinet Industrial PC C6640/ C6650 up to -0030 Installation and Operating instructions for Control Cabinet Industrial PC C6640/ C6650 up to -0030 Version: 1.6 Date: 2018-01-24 Table of contents Table of contents 1. 2. 3. Foreword 3 Notes on the Documentation

More information

CU port USB 2.0 hub. Version: 1.1 Date:

CU port USB 2.0 hub. Version: 1.1 Date: CU8004-0000 4 port USB 2.0 hub Version: 1.1 Date: 2006-08-11 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions of delivery

More information

19-inch slide-in Industrial PC C5210

19-inch slide-in Industrial PC C5210 Installation and Operating instructions for 19-inch slide-in Industrial PC C5210 Version: 1.2 Date: 2016-12-08 Table of contents Table of contents 1 Foreword 4 1.1 Notes on the Documentation 4 1.1.1 Liability

More information

Installation- and Operating instructions for CU CFast card adapter with USB connector. Version: 1.1 Date:

Installation- and Operating instructions for CU CFast card adapter with USB connector. Version: 1.1 Date: Installation- and Operating instructions for CU8871-0000 CFast card adapter with USB connector Version: 1.1 Date: 2013-12-06 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation

More information

Installation and Operating instructions for CP / CP Economy Built-in Panel PC. Version: 1.

Installation and Operating instructions for CP / CP Economy Built-in Panel PC. Version: 1. Installation and Operating instructions for CP6600-0001-0020/ CP6606-0001-0020 Economy Built-in Panel PC Version: 1.3 Date: 2017-12-05 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the

More information

CU Compact-Flash card adapter for USB. Version: 1.0 Date:

CU Compact-Flash card adapter for USB. Version: 1.0 Date: CU8870-0000 Compact-Flash card adapter for USB Version: 1.0 Date: 2007-06-15 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions

More information

Installation and Operating instructions for Build-in Industrial PC C33xx up to -0050

Installation and Operating instructions for Build-in Industrial PC C33xx up to -0050 Installation and Operating instructions for Build-in Industrial PC C33xx up to -0050 Version: 1.5 Date: 2018-01-31 Foreword Table of contents 1. 2. 3. 4. Foreword 3 Notes on the Documentation 3 Liability

More information

Installation- and Operating instructions for CU CP-Link 4 transmitter box The Two Cable Display Link. Version: 1.

Installation- and Operating instructions for CU CP-Link 4 transmitter box The Two Cable Display Link. Version: 1. Installation- and Operating instructions for CU8802-0000 CP-Link 4 transmitter box The Two Cable Display Link Version: 1.1 Date: 2015-08-27 Table of contents Table of contents 1 Foreword 3 1.1 Notes on

More information

Installation and Operating instructions for CP78xx Control Panel. Version: 1.8 Date:

Installation and Operating instructions for CP78xx Control Panel. Version: 1.8 Date: Installation and Operating instructions for CP78xx Control Panel Version: 1.8 Date: 2016-03-14 Table of contents Table of contents 1. 2. 3. 4. 5. 6. General Notes 2 Notes on the documentation 2 Liability

More information

Installation and Operating instructions for. Built-in Control Panel CP68xx. Version: 2.0 Date:

Installation and Operating instructions for. Built-in Control Panel CP68xx. Version: 2.0 Date: Installation and Operating instructions for Built-in Control Panel CP68xx Version: 2.0 Date: 2007-11-05 General Notes Table of contents 1. 2. 3. 4. 5. 6. General Notes 2 Notes on the documentation 2 Liability

More information

Installation and Operating instructions for. C inch slide-in Industrial PC. Version: 1.0 Date:

Installation and Operating instructions for. C inch slide-in Industrial PC. Version: 1.0 Date: Installation and Operating instructions for C5240 19-inch slide-in Industrial PC Version: 1.0 Date: 2019-02-08 Table of contents Table of contents 1 Foreword 4 1.1 Notes on the Documentation 4 1.1.1 Liability

More information

Installation and Operating instructions for CP / CP Economy Built-in Panel PC. Version: 1.

Installation and Operating instructions for CP / CP Economy Built-in Panel PC. Version: 1. Installation and Operating instructions for CP6700-0001-0050/ CP6706-0001-0050 Economy Built-in Panel PC Version: 1.1 Date: 2017-12-13 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the

More information

Operating instructions for AX5801. TwinSAFE drive option card for the AX5000 servo drive. Version: Date:

Operating instructions for AX5801. TwinSAFE drive option card for the AX5000 servo drive. Version: Date: Operating instructions for AX5801 TwinSAFE drive option card for the AX5000 servo drive Version: 1.2.0 Date: 2016-03-15 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the manual 3 1.1.1

More information

Installation and Operating instructions for. CP79xx Control Panel. Version: 1.5 Date:

Installation and Operating instructions for. CP79xx Control Panel. Version: 1.5 Date: Installation and Operating instructions for CP79xx Control Panel Version: 1.5 Date: 2011-06-27 Table of contents Table of contents 1. 2. 3. 4. 5. 6. Foreword 2 Notes on the Documentation 2 Liability Conditions

More information

Installation and Operating instructions for. CP79xx Control Panel. Version: 1.2 Date:

Installation and Operating instructions for. CP79xx Control Panel. Version: 1.2 Date: Installation and Operating instructions for CP79xx Control Panel Version: 1.2 Date: 2007-11-05 Table of contents Table of contents 1. 2. 3. 4. 5. 6. General Notes 2 Notes on the documentation 2 Liability

More information

Installation and Operating instructions for. CP37xx. Multi-touch Panel PC. Version: 1.2 Date:

Installation and Operating instructions for. CP37xx. Multi-touch Panel PC. Version: 1.2 Date: Installation and Operating instructions for CP37xx Multi-touch Panel PC Version: 1.2 Date: 2018-04-12 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation 3 1.1.1 Liability

More information

Installation and Operating instructions for. CP32xx. Multi-touch Panel PC. Version: 1.7 Date:

Installation and Operating instructions for. CP32xx. Multi-touch Panel PC. Version: 1.7 Date: Installation and Operating instructions for CP32xx Multi-touch Panel PC Version: 1.7 Date: 2016-11-07 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation 3 1.1.1 Liability

More information

Documentation EM2042. Sixteen Channel Digital Output Module with D-Sub Connector. Version: Date:

Documentation EM2042. Sixteen Channel Digital Output Module with D-Sub Connector. Version: Date: Documentation Sixteen Channel Digital Output Module with D-Sub Connector Version: Date: 2.0 2016-08-03 Table of contents Table of contents 1 Foreword... 4 1.1 Notes on the documentation... 4 1.2 Safety

More information

Installation and Operating instructions for Control Panel CP77xx. Version: 1.6 Date:

Installation and Operating instructions for Control Panel CP77xx. Version: 1.6 Date: Installation and Operating instructions for Control Panel CP77xx Version: 1.6 Date: 2007-10-29 General Notes Table of contents 1. 2. 3. 4. 5. 6. General Notes 2 Notes on the documentation 2 Liability

More information

CP29xx-0010 Multi-touch Control Panel with CP-Link 4 interface

CP29xx-0010 Multi-touch Control Panel with CP-Link 4 interface Installation and Operating instructions for CP29xx-0000 Multi-touch Control Panel with DVI/ USB Extended interface CP29xx-0010 Multi-touch Control Panel with CP-Link 4 interface Version: 1.8 Date: 2015-08-27

More information

Documentation KM2042. Sixteen channel digital output module with D-Sub Connector. Version: Date:

Documentation KM2042. Sixteen channel digital output module with D-Sub Connector. Version: Date: Documentation Sixteen channel digital output module with D-Sub Connector Version: Date: 2.0.0 2017-11-20 Table of contents Table of contents 1 Foreword... 5 1.1 Notes on the documentation... 5 1.2 Safety

More information

Installation and Operating instructions for. CP69xx. Built-in Control Panel with DVI/ USB Extended interface. Version: 2.

Installation and Operating instructions for. CP69xx. Built-in Control Panel with DVI/ USB Extended interface. Version: 2. Installation and Operating instructions for CP69xx Built-in Control Panel with DVI/ USB Extended interface Version: 2.4 Date: 2017-01-06 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the

More information

Documentation ZB8610. Fan cartridge for EtherCAT and Bus Terminals. Version: Date:

Documentation ZB8610. Fan cartridge for EtherCAT and Bus Terminals. Version: Date: Documentation Fan cartridge for EtherCAT and Bus Terminals Version: Date: 1.5 2017-08-07 Table of contents Table of contents 1 Foreword... 5 1.1 Notes on the documentation... 5 1.2 Safety instructions...

More information

Documentation. Mains filter AX2090-NF50. Version: Date:

Documentation. Mains filter AX2090-NF50. Version: Date: Documentation Mains filter AX2090-NF50 Version: Date: 1.1 2015-11-11 Table of content Table of content 1 Foreword... 4 1.1 Notes on the documentation... 4 1.2 Documentation issue status... 5 1.3 Appropriate

More information

Documentation. KM2604 and KM2614. Four channel relay module. Version: Date:

Documentation. KM2604 and KM2614. Four channel relay module. Version: Date: Documentation KM2604 and KM2614 Four channel relay module Version: Date: 2.1.0 2017-12-01 Tabel of contents Tabel of contents 1 Foreword... 5 1.1 Notes on the documentation... 5 1.2 Safety instructions...

More information

Installation and Operating instructions for. CP790x-140x. IP65 Stainless Control Panel. Version: 1.1 Date:

Installation and Operating instructions for. CP790x-140x. IP65 Stainless Control Panel. Version: 1.1 Date: Installation and Operating instructions for CP790x-140x IP65 Stainless Control Panel Version: 1.1 Date: 2013-01-17 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the Documentation 3 1.1.1

More information

Installation and Maintenance

Installation and Maintenance Installation and Maintenance TT1000 TT3000 TT4000 Version 1.3 e-data GmbH 01.2009 Version 1.3 1-1 1 Usage 1-3 1.1 Protection Class and Protection Type... 1-3 1.2 Safety Measures... 1-3 1.3 Before Commissioning...

More information

Operation Manual BK5000. Bus Coupler for CAN-CAL Version: 1.12

Operation Manual BK5000. Bus Coupler for CAN-CAL Version: 1.12 Operation Manual BK5000 Bus Coupler for CAN-CAL 2006-11-27 Version: 1.12 Table of Contents Table of Contents 1. Foreword 1 Notes on the documentation 1 Safety Instructions 2 2. Configuration of the Bus

More information

LVN5200A-R2, rev. 1, Hardware Installation Guide

LVN5200A-R2, rev. 1, Hardware Installation Guide LVN5200A-R2 LVN5250A-R2 LVN5200A-R2, rev. 1, Hardware Installation Guide Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical support

More information

MC 11 EB-2 Power supply cabinet with external bus, AC version

MC 11 EB-2 Power supply cabinet with external bus, AC version MC 11 EB-2 Power supply cabinet with external bus, AC version USER/MAINTENANCE MANUAL 1 SLOT 0 SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 5 SLOT 6 SLOT 7 SLOT 8 SLOT 9 SLOT 10 SLOT 11 EB-2 (a) MC11 (b) (c) Figures

More information

Broadband Automatic Disconnect Switch. User Manual

Broadband Automatic Disconnect Switch. User Manual Reset/Test Primary/ Primary Broadband Automatic Disconnect Switch User Manual Local Power Remote Pwer Local 63V Fault Secondary Select Secondary 220V Normal 990-1929 09/2004 Introduction Introduction

More information

CP39xx-0010 Multi-touch Control Panel with CP-Link 4 interface

CP39xx-0010 Multi-touch Control Panel with CP-Link 4 interface Installation and Operating instructions for CP39xx-0000 Multi-touch Control Panel with DVI/ USB Extended interface CP39xx-0010 Multi-touch Control Panel with CP-Link 4 interface Version: 2.2 Date: 2016-06-30

More information

Manual CX Audio interface for CX20x0. Version: Date:

Manual CX Audio interface for CX20x0. Version: Date: Manual Audio interface for CX20x0 Version: Date: 1.0 12/19/2013 Inhaltsverzeichnis Inhaltsverzeichnis 1 Foreword... 4 1.1 Notes on the documentation... 4 1.2 Safety instructions... 5 1.3 Documentation

More information

Emerson Network Power provides customers with technical support. Users may contact the nearest Emerson local sales office or service center.

Emerson Network Power provides customers with technical support. Users may contact the nearest Emerson local sales office or service center. Liebert PSA iton User Manual Version: V2.8 Revision date: November 14, 2005 Emerson Network Power provides customers with technical support. Users may contact the nearest Emerson local sales office or

More information

DS-1H05 Ethernet-over-Coax Extender. User Manual

DS-1H05 Ethernet-over-Coax Extender. User Manual DS-1H05 Ethernet-over-Coax Extender User Manual Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to DS-1H05-T,

More information

Description AX5805. List of permissible motors. Version: Date:

Description AX5805. List of permissible motors. Version: Date: Description AX5805 List of permissible motors Version: 1.6.0 Date: 2017-11-15 Table of contents Table of contents 1 Foreword 3 1.1 Notes on the manual 3 1.1.1 Intendent audience 3 1.1.2 Origin of the

More information

4170 POS System Installation Guide

4170 POS System Installation Guide 4170 POS System 4170 Installation Guide Thank you for selecting UTC RETAIL s innovative Model 4170 Point of Sale solution! This Installation Guide will help you efficiently install the 4170 POS. The document

More information

Manual Version: V1.00. Video Decoder Quick Guide

Manual Version: V1.00. Video Decoder Quick Guide Manual Version: V1.00 Video Decoder Quick Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. Copyright Copyright 2016 Zhejiang

More information

CPCI-PS24 24V-Power Supply

CPCI-PS24 24V-Power Supply 24V-Power Supply Hardware Manual to Product I.2301.21 esd electronic system design gmbh Vahrenwalder Str. 207 30165 Hannover Germany http://www.esd.eu Phone: +49 (0) 511 3 72 98-0 Fax: +49 (0) 511 3 72

More information

EL9820/EL9821 Evaluation Kit. Version: 1.3 Date:

EL9820/EL9821 Evaluation Kit. Version: 1.3 Date: EL9820/EL9821 Evaluation Kit Version: 1.3 Date: 2015-05-25 Table of contents Table of contents 1 Foreword 2 1.1 Notes on the documentation 2 1.1.1 Liability conditions 2 1.1.2 Delivery conditions 2 1.1.3

More information

icore Kiosk system Installation Guide

icore Kiosk system Installation Guide icore Kiosk system Installation Guide The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights,

More information

Documentation. KM10xx. Terminal Modules with Digital Inputs. Version: Date:

Documentation. KM10xx. Terminal Modules with Digital Inputs. Version: Date: Documentation KM10xx Terminal Modules with Digital Inputs Version: Date: 3.1.0 2017-01-23 Product overview KM10xx Product overview KM10xx KM1002, KM1012 [} 11] - 16 inputs, input filter 3 or 0.2 ms KM1004,

More information

Thank you for selecting UTC RETAIL s innovative Model 1170 Point of Sale solution!

Thank you for selecting UTC RETAIL s innovative Model 1170 Point of Sale solution! 1170 POS SYSTEM 1170 INSTALLATION GUIDE Thank you for selecting UTC RETAIL s innovative Model 1170 Point of Sale solution! This Installation Guide will help you efficiently install the 1170 POS. The document

More information

Operating and Installation Manual. EASYLAB Expansion modules Type EM-TRF for 230 V AC mains voltage

Operating and Installation Manual. EASYLAB Expansion modules Type EM-TRF for 230 V AC mains voltage Operating and Installation Manual EASYLAB Expansion modules Type EM-TRF for 230 V AC mains voltage Type EM-TRF-USV for 230 V AC mains voltage; provides uninterruptible power supply (UPS) The art of handling

More information

user manual AMOS-2000 Universal Compact, Chassis System, Supporting Nano-ITX Embedded Boards Revision

user manual AMOS-2000 Universal Compact, Chassis System, Supporting Nano-ITX Embedded Boards Revision Revision 0.20 020-10122009-1415 user manual AMOS-2000 Universal Compact, Chassis System, Supporting Nano-ITX Embedded Boards Copyright and Trademarks Copyright 2009 VIA Technologies Incorporated. All rights

More information

Model 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1

Model 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1 Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 2460-KIT Screw Terminal Connector Kit Description The Model 2460-KIT Screw Terminal Connector Kit

More information

Documentation. CU20xx, CU22xx. Ethernet Switch. Version: Date:

Documentation. CU20xx, CU22xx. Ethernet Switch. Version: Date: Documentation CU20xx, CU22xx Ethernet Switch Version: Date: 2.1 2017-12-18 CU20xx, CU22xx - Product overview 1 CU20xx, CU22xx - Product overview CU2005 [} 8] - 5 RJ-45-Ethernet-Ports CU2008 [} 8] - 8

More information

Documentation KM2002, KM2004, KM2008. Terminal modules with digital outputs, 24 V, 0.5 A. Version: Date:

Documentation KM2002, KM2004, KM2008. Terminal modules with digital outputs, 24 V, 0.5 A. Version: Date: Documentation KM2002, KM2004, KM2008 Terminal modules with digital outputs, 24 V, 0.5 A Version: Date: 3.2.0 2017-01-23 Table of contents Table of contents 1 Foreword... 4 1.1 Notes on the documentation...

More information

DC-D2212R / DC-D2212WR

DC-D2212R / DC-D2212WR Network Camera Quick Guide / DC-D2212WR Powered by Safety Precautions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

More information

Documentation KL channel Digital Output Terminal, 24 V DC, 2 x 4 A/1 x 8 A. Version: Date:

Documentation KL channel Digital Output Terminal, 24 V DC, 2 x 4 A/1 x 8 A. Version: Date: Documentation 2 channel Digital Output Terminal, 24 V DC, 2 x 4 A/1 x 8 A Version: Date: 1.0.0 2016-08-12 Table of contents Table of contents 1 Foreword... 4 1.1 Notes on the documentation... 4 1.2 Safety

More information

Obtaining Documentation and Submitting a Service Request, page xvii Safety Warnings, page xvii Safety Guidelines, page xx

Obtaining Documentation and Submitting a Service Request, page xvii Safety Warnings, page xvii Safety Guidelines, page xx Preface Obtaining Documentation and Submitting a Service Request, page xvii Safety s, page xvii Safety Guidelines, page xx Obtaining Documentation and Submitting a Service Request For information on obtaining

More information

BEETLE /Fusion Compact. Installation Guide

BEETLE /Fusion Compact. Installation Guide BEETLE /Fusion Compact Installation Guide The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights,

More information

Operating Instructions (Compact) SIMATIC. Industrial PC SIMATIC Microbox PC 420. Siemens. Release 11/2006 A5E

Operating Instructions (Compact) SIMATIC. Industrial PC SIMATIC Microbox PC 420. Siemens. Release 11/2006 A5E Operating Instructions (Compact) 1 SIMATIC Industrial PC Release 11/2006 A5E00344128-04 Siemens Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety,

More information

Display Panel BAT 100 LSN. en Operation Guide

Display Panel BAT 100 LSN. en Operation Guide Display Panel BAT 100 LSN en Operation Guide Display Panel Table of Contents en 3 Table of contents 1 Safety 4 2 Short information 4 3 System overview 5 4 Installation 6 5 Connection 11 6 Maintenance

More information

Installation manual plugs and connectors with screw connection (16/32 A)

Installation manual plugs and connectors with screw connection (16/32 A) EN Installation manual plugs and connectors with screw connection (16/32 60003213 Issue 04.2016 2016-04-01 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3

More information

SINAMICS G130. Terminal Module 150 (TM150) Operating Instructions 03/2013 SINAMICS

SINAMICS G130. Terminal Module 150 (TM150) Operating Instructions 03/2013 SINAMICS SINAMICS G130 Operating Instructions 03/2013 SINAMICS s Safety information 1 General information 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5

More information

PanelView Plus/VersaView CE Terminals and Display Modules

PanelView Plus/VersaView CE Terminals and Display Modules Installation Instructions PanelView Plus/VersaView CE Terminals and Display Modules (Catalog Numbers 2711P-xxxxxx, 6182H-xxxxxx) English Inside: Overview...2 For More Information...2 Modular Components...3

More information

Network Camera. Quick Guide DC-B1203X. Powered by

Network Camera. Quick Guide DC-B1203X. Powered by Network Camera Quick Guide DC-B1203X Powered by Safety Precautions English WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

More information

User Manual AIMB-C200. Economical Embedded Chassis for Mini-ITX Motherboard

User Manual AIMB-C200. Economical Embedded Chassis for Mini-ITX Motherboard User Manual AIMB-C200 Economical Embedded Chassis for Mini-ITX Motherboard Copyright The documentation and the software included with this product are copyrighted 2010 by Advantech Co., Ltd. All rights

More information

USER MANUAL. Uninterruptible Power Supply Line-interactive VCL Series UPS VA. GE Critical Power

USER MANUAL. Uninterruptible Power Supply Line-interactive VCL Series UPS VA. GE Critical Power Critical Power USER MANUAL Uninterruptible Power Supply Line-interactive VCL Series UPS 400 600 800 1000 1500 VA GE Consumer & Industrial SA General Electric Company CH 6595 Riazzino (Locarno) Switzerland

More information

PNOZ m ES RS232. Configurable Control System PNOZmulti. Operating Manual EN-01

PNOZ m ES RS232. Configurable Control System PNOZmulti. Operating Manual EN-01 PNOZ m ES RS232 Configurable Control System PNOZmulti Operating Manual-1002701-EN-01 This document is the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies

More information

Junos WebApp Secure 5.0 Hardware Guide

Junos WebApp Secure 5.0 Hardware Guide Junos WebApp Secure 5.0 Hardware Guide Junos WebApp Secure 5.0 Hardware Guide This document contains a specification for the MWS1000 hardware appliance, as well as instructions for installation into a

More information

Operating Manual -ENGLISH- Page 1 KWG-ISO

Operating Manual -ENGLISH- Page 1 KWG-ISO Page 1 KWG-ISO Operating manual English- Status May 2013 Page 2 Manufacturer address KW-Generator GmbH & Co.KG Bänglesäcker 24 73527 Schwäbisch-Gmünd / Lindach Phone: +49 (0) 7171 104 17 0 Fax: +49 (0)

More information

JanusRAID SA-6692J Hardware User Manual

JanusRAID SA-6692J Hardware User Manual JanusRAID SA-6692J Hardware User Manual 42-30000-5067 SATA II JBOD enclosure Version 1.1 SA-6692J SATA II JBOD enclosure Hardware User Manual Table of Contents Preface... i Chapter 1 System Requirements

More information

USER GUIDE. AXIS T8120 Midspan 15 W 1-port ENGLISH

USER GUIDE. AXIS T8120 Midspan 15 W 1-port ENGLISH USER GUIDE AXIS T8120 Midspan 15 W 1-port ENGLISH Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before

More information

PHOENIX CONTACT - 07/2006

PHOENIX CONTACT - 07/2006 Buffer module with maintenance-free capacitor-based power storage device INTERFACE Data sheet 102035_03_en PHOENIX CONTACT - 07/2006 Description Short-term mains interruptions are bridged by QUINT BUFFER,

More information

USP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10

USP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10 UniStream HMI Panel Installation Guide USP-070-B10, USP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10 Unitronics UniStream platform comprises control devices that provide robust, flexible solutions for

More information

dv/dt filter compact plus Voltage Peak Limiter SINAMICS SINAMICS G120P dv/dt filter compact plus Voltage Peak Limiter Safety information 1 General 2

dv/dt filter compact plus Voltage Peak Limiter SINAMICS SINAMICS G120P dv/dt filter compact plus Voltage Peak Limiter Safety information 1 General 2 dv/dt filter compact plus Voltage Peak Limiter SINAMICS SINAMICS G120P dv/dt filter compact plus Voltage Peak Limiter Operating Instructions Safety information 1 General 2 Mechanical installation 3 Electrical

More information

AURA SSD FOR MAC PRO. Installation Guide

AURA SSD FOR MAC PRO. Installation Guide AURA SSD FOR MAC PRO Installation Guide CONTENTS Introduction... 1 1.1 System Requirements 1.2 Package Contents 1.3 About This Manual Installation... 2 2.1 Preparing the Mac Pro 2.2 Installing the Aura

More information

Line reactors SINAMICS. SINAMICS G120P Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation 4

Line reactors SINAMICS. SINAMICS G120P Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation 4 Safety information 1 General 2 SINAMICS SINAMICS G120P Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.6 11/2013 A5E32845290B AA

More information

hp uninterruptible power system r12000 xr models installation instructions

hp uninterruptible power system r12000 xr models installation instructions hp uninterruptible power system r000 xr models installation instructions Overview These instructions show how to install an uninterruptible power system (UPS). For detailed information about the UPS, refer

More information

DC-D4213RX DC-D4213WRX

DC-D4213RX DC-D4213WRX Network Camera Quick Guide DC-D4213RX DC-D4213WRX Powered by Safety Precautions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

More information

VL BPC MINI. A configurable industrial computer platform Intel Atom Z510PT CMAT IPC Module Option [I28] AUTOMATION Data Sheet 2930_en_A.

VL BPC MINI. A configurable industrial computer platform Intel Atom Z510PT CMAT IPC Module Option [I28] AUTOMATION Data Sheet 2930_en_A. A configurable industrial computer platform Intel Atom Z0PT CMAT IPC Module Option [I8] AUTOMATION Data Sheet 90_en_A Description PHOENIX CONTACT 0-0-0 Features The VL BPC MINI is an embedded box PC and

More information

Redundancy unit CP-A RU

Redundancy unit CP-A RU 2CDC 271 010 F0t06 Features Decoupling of CP power supply units with 2 inputs, each up to 20 A per input / channel Output up to 40 A True redundancy by 100 % decoupling of two parallel connected power

More information

Perle MCR200 Installation Guide

Perle MCR200 Installation Guide Perle MCR200 Installation Guide P/N 5500322-10 Introduction The Perle MCR200 Chassis is a 2 slot chassis able to accommodate up to 2 Perle Media Converter modules or 1 Media Converter Module and an MCR-MGT

More information

Serial Module RS232C Standard. Technical Description

Serial Module RS232C Standard. Technical Description Computertechnik GmbH Serial Module RS232C Standard Technical Description Order number: 404.249010.000 6 ISA96 Serial Module RS323C standard Your contact: 2001 by Janich & Klass Computertechnik GmbH, Wuppertal

More information