XW3B. Connector Terminal Boxes. Ratings and Specifications. Compatible Connectors. Materials and Finish

Transcription

1 es XWB Series Includes New Lightweight, Low-profile Connector Terminal Boxes for Use Outside of Control Boxes to Centralize I/O with Reduced Labor and Greater Environmental Resistance Tough model with a significantly lower profile satisfies IP. Available for Photoelectric s, Proximity s, and es with I/O (M). Increased rated current, with added ground terminal, and compatible with valves and solenoids. Incorporates power and operation indicators. Uses a single mounting method regardless of the number of ports, which ensures easy system expansion. / Ratings and Specifications Rated current A/port (signal lines) A/box (power lines) Rated voltage 0 to 0 VDC Contact resistance 0 MΩ max. (with 00 ma max., 0 mv max.)* Insulation resistance 00 MΩ min. (at 00 VDC) Dielectric strength 00 VAC for min (leakage current: ma max.)* Degree of protection IP (IEC) Cable retention force N/ s Insertion tolerance 00 times Operating temperature to 0 C *. The contact resistance of the Connector. *. The dielectric strength of the Connector. Compatible / /XW XWB XS G W H Connector Plug Assemblies (crimping, soldering, or screw-on) on cable ends (Sockets or Plugs) on one cable end (Plugs) Materials and Finish Item Part name Materials and finish Anchor Brass/nickel plated Contacts Brass/nickel base, 0.-μm gold plating Cable Cable Sheath color: gray Core size: AWG/AWG * Case PBT resin (ULV-0)/light gray Case Bushing Rubber PCB Glass-epoxy board Seal resin Urethane resin * The positive power supply, negative power supply, and ground lines are AWG. Signal lines are AWG.

2 XWB XWB Dimensions (Unit: mm) (Four Input Ports) indicator (green LED) Operation indicator (red LED). Three,. dia.. dia. L dia. Internal connection indication. 0 XWB-P@-@ (Six Input Ports) indicator (green LED) Operation indicator (red LED). Three,. dia.. dia L / XWB-P@-@ (Eight Input Ports)... dia. dia. dia. Internal connection indication indicator (green LED) Operation indicator (red LED). 0 Three,. dia.. dia. L dia. dia.. dia. Internal connection indication 0 / /XW XWB XS

3 XWB Ordering Information type and connections -wire DC /-wire DC - -wire DC-/ without polarity - -wire DC /-wire DC - Actuator connections Actuator connections - Actuator connections - No. of ports Cable length (m) Model Model Model XWB-P-G XWB-P-G XWB-P-G XWB-P-G XWB-P-G XWB-P-G XWB-P-G XWB-P-G XWB-P-G Note: Here - and - are connector pin numbers. Connection Diagrams Standard Japanese Specification XWB-P@-@ for -wire DC, -wire DC (without polarity -), and Actuator (-) -WIRE Japanese Specification European Specification XWB-P@-@ for -wire DC XWB-P@-@ for -wire DC, (with polarity -, without polarity -) -wire DC (with polarity -), and Note: Cannot be used with -type Photoelectric and Actuator (-) Proximity s. Cannot be used with Proximity s with polarity -. -WIRE -WIRE Positive power supply (Brown) indicator (Green LED) Negative power supply (Blue) Ground (Green/Yellow) Connector pin number Positive power supply (Brown) indicator (Green LED) Negative power supply (Blue) Ground (Green/Yellow) Connector pin number Positive power supply (Brown) indicator (Green LED) Negative power supply (Blue) Ground (Green/Yellow) Connector pin number / Signal (White) Lead color Signal (Green) Signal (Yellow) Operation indicator (Red LED) Signal (White) Lead color Signal (Green) Signal (Yellow) Operation indicator (Red LED) Signal (White) Lead color Signal (Green) Signal (Yellow) Operation indicator (Red LED) Signal (Gray) Signal (Pink) Signal (Red) Signal (Black) Signal (Purple) Signal (Gray) Signal (Pink) Signal (Red) Signal (Black) Signal (Purple) Note:. The above wiring diagrams are for eight-port use.. Figures in parentheses indicate lead colors.. The expression white/red means white and red stripes.. Here - and - are pin numbers. Signal (Gray) Signal (Pink) Signal (Red) Signal (Black) Signal (Purple) / /XW XWB XS

4 Mounting Holes XWB (Unit: mm) Three, M or. dia. ±0. ±0. Note: Mounting hole dimensions are always the same regardless of the number of ports. Safety Precautions Refer to Warranty and Limitations of Liability on page F-. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed Applicable product ratings. Connector Connection or Disconnection Before using a or, check this catalog and be sure that the or can be connected. Be sure to turn OFF the power supplied to the XWB before Connector connection or disconnection. Do not touch the engaged side of any Connector with a wet hand. If a Connector is wet with water, wipe the Connector and be sure that the connector is completely dry. Be sure that there is no metal plate or powder on the engaged side of any Connector. Cable Connection Be sure to wire the cable correctly according to the wiring diagram so that the blue wire will be connected to the negative power supply terminal and the brown wire will be connected to the positive power supply terminal. If there is any wiring mistake, the load will not operate or the operation indicator will not light. Be sure to connect a load to the signal lines to operate the and Actuator. Applicable are the G (assembly type), H (monoblock type), and W (monoblock type). After a Connector is engaged, tighten the Connector securely with a mounting bracket. Be sure to put the Z- Waterproof Cover or Z- Dust Cover on any Connector that is not used. Supply and Operation Indicators When power is supplied, the green power indicator will be lit. When the s and Actuators are operating, the corresponding red operation indicators will be lit. Only DC s and Actuators can be connected to the XWB. Do not connect AC s or Actuators. es are internally wired with or wires. The type is marked on the case. -WIRE -WIRE -WIRE / / /XW XWB XS

5 XWB Input Device Connections Using I/O Direct Connection Type Connection Type Pre-wired Type Proximity Photoelectric W Cable with connector Proximity Photoelectric Proximity Photoelectric G Connector Assembly (solderless/soldering type) XWB XWB XWB Input Using I/O / / /XW XWB XS Connector Terminal Box XWB-P@-G XWB-P@-G XWB-P@-G Cable W-D@-@-A W-D@-@-A -wire DC Proximity -wire DC Proximity () Photoelectric () Note: Use the G Connector assembly in combination with a pre-wired input device. *. Any of these models is available provided that only its SPST-NO contact is used. *. Any of these models is available provided that it uses an NO connection. Input devices using I/O EE-XD-MJ-T, EE-XD-MJ-T, EE-X0D-MJ-T EE-X@D-M EE-XE-M, EE-XE-M, EE-X0E-M EE-XME-M, EE-X0ME-M, EE-XME-M ES-AT, ES-AT, ES-AD, ES-AD, ES-AD, ES-AD, ES-AD, ES-AD, ES-AR, ES-AR WL@-@DKEJ@ *, WL@-@-MGJ *, DC-@0@@-DKEJ@ * W-D@-@-A WL@-@K *, DE-@@0N * W-D@-@-A W-D@-@-A W-D@-@-A -wire DC Proximity () Photoelectric () -wire DC Proximity W-D@-@-A EE-XF-M, EE-XF-M, EE-X0F-M EE-XMF-M, EE-X0MF-M, EE-XMF-M ES-AT, ES-AT, ES-AD, ES-AD, ES-AD, ES-AD, ES-AD, ES-AD, ES-AR, ES-AR EE-XD-MGJ, EE-XD-MJ-T, EE-XD-MGJ, EE-XD-MJ-T, EE-X0D-MGJ, EE-X0D-MJ-T EE-XMD-MGJ, EE-XMD-MGJ, EE-X0MD-MGJ EEQ-XD-MGJ, EEQ-XD-MGJ, EEQ-X0D-MGJ EE-XD-MG, EE-XD-MG, EE-X0D-MG EE-XMD-MG, EE-XMD-MG, EE-X0MD-MG WL@-@DKEJ@ *, WL@-@-MGJ *, DC-@0@@-DKEJ@ * WL@-@K *, DE-@@0N *, DCC-@@@@ *

6 XWB Attaching the G Connector to Pre-wired Input Device -wire DC () : +, :, : output -wire DC (with polarity) : +, : Input devices and connector pin number -wire DC (with polarity) :, : + -wire DC (with no polarity), -wire DC () : +, :, : output XWB-P@-G Yes No Yes Yes Yes No XWB-P@-G No Yes No No No Yes XWB-P@-G No Yes No Yes Yes No es for Input with I/O Photoelectric s Proximity s es Input device Type Connection method Model -wire DC -wire DC ES-AT/, ES-AR/, and ES-AD///// ES-AT/, ES-AR/, and ES-AD///// EE-X@D-MJ-T EE-X@D-MGJ and EE-X@D-MJ-T EE-X@MD-MGJ EEQ-X@D-MGJ EE-X@D-MG EE-X@MD-MG EE-X@D-M EE-X@E-M EE-X@ME-M EE-X@F-M EE-X@MF-M WL@-@DKEJ@ *, WL@-@-MJ *, and DC-@0@@-DKEJ@ * WL@-@K * and DE-@@0N * DCC-@@@@ * *. Any of these models is available provided that only its SPST-NO contact is used. *. Any of these models is available provided that it uses an NO connection. Cable W-D@-@-A See the models above for components that are compatible with I/O. Connector Terminal Box XWB-P@-G XWB-P@-G XWB-P@-G XWB-P@-G XWB-P@-G XWB-P@-G XWB-P@-G, XWB-P@-G XWB-P@-G / / /XW XWB XS Cat. No. G0-E-0 In the interest of product improvement, specifications are subject to change without notice.