Perle PoE/PoE+ 10/100 Ethernet Media Converters
|
|
- Leslie Annis Long
- 6 years ago
- Views:
Transcription
1 Perle PoE/PoE+ 10/100 Ethernet Media Converters Installation Guide S-110-P S-110PP S-110P-SFP S-110PP-SFP S-110P-XT S-110PP-XT S-110P-SFP-XT S-110PP-SFP-XT Part# (Rev B)
2 Overview This document contains instructions necessary for the installation and operation of the Perle Standalone PoE/PoE+ 10/100 rate converting Media Converters (S-110P). These products have the ability to convert 10/100Base-T cable connections (copper) to 100Base-X connection (fiber). The Perle media converters function as a PoE switch, and support a variety of port configurations. These media converters function as Power Sourcing Equipment (PSE) and can power up one Powered Device (PD) using standard UTP cables that carry Ethernet data. The S-110P models are compatible with Powered Devices that comply with the IEEE 802.3af standard and the S-110PP models are compatible with Powered Devices that comply with both the IEEE 802.3af and the 802at-2009 standards. The fiber connection can be either single mode () or multimode (MM) and can operate over different wavelengths and distances, depending on the model selected (see table below). POE/POE+ PoE (P) PoE+ (PP) Connector (xx) Mode Distance Wavelength (TX/RX) S-110P-M2xx2 S-110PP-M2xx2 S-110P-M1xx2U S-110PP-M1xx2U S-110P-M1xx2D S-110PP-M1xx2D S-110P-S2xx20 S-110P-S2xx20 S-110P-S2xx40 S-110PP-S2xx40 S-110P-S2xx80 S-110PP-S2xx80 S-110P-S2xx120 S-110PP-S2xx120 S-110P-S1ST20U S-110PP-S1ST20U S-110P-S1ST20D S-110PP-S1ST20D SC/ST SC/ST SC/ST SC/ST SC/ST SC/ST ST ST ST MM 2 km/1.2 mi. MM 2 km/1.2 mi. MM 2 km/1.2 mi. 20 km/12.4 mi. 40 km/24.9 mi. 80 km/49.7 mi. 120 km/ km/12.4 mi. 20 km/12.4 mi nm 1310/1550 nm 1550/1310 nm 1310 nm 1310 nm 1550 nm 1550 nm 1310/1550 nm 1550/1310 nm 2
3 PoE (P) PoE+ (PP) S-110P-S1SC40U S-110PP-S1SC40U S-110P-S1SC40D S-110PP-S1SC40D S-110P-SFP S-110PP-SFP Connector (xx) SC SC Mode Distance 40 km/24.9 mi. 40 km/24.9 mi. SFP NOTE 1 Wavelength (TX/RX) 1510/1590 nm 1590/1510 nm Extended Temperature Models PoE (P) PoE+ (PP) S-110P-M2xx2-XT S-110PP-M2xx2-XT S-110P-S2xx20-XT S-110P-S2xx20-XT S-110P-S1SC20U-XT S-110PP-S1SC20U-XT S-110P-S1SC20D-XT S-110PP-S1SC20D-XT S-110P-SFP-XT S-110PP-SFP-XT Connector (xx) SC/ST SC/ST SC SC Mode Distance MM 2 km/1.2 mi. 20 km/12.4 mi. 20 km/12.4 mi. 20 km/12.4 mi. SFP NOTE 1 Wavelength (TX/RX) 1310 nm 1310 nm 1310/1550 nm 1550/1310 nm Note 1: Fiber characteristics will depend on the SFP fiber module selected. Installation The default DIP switch settings (all switches in the UP position) will work for most installations. These are the steps required to configure the Perle S-110P Ethernet media converter: 1. Insert SFP Module (SFP Model only). 2. Set the DIP switch settings (if required). 3. Set the Powering Option Jumpers (if required). 4. Install and connect the fiber cable. 5. Install and connect the copper cable. 6. Install the Power cord Relief clip (optional). 7. Power up the media converter. 3
4 Power Sourcing Pinouts When Power Sourcing is enabled on a copper port, the S- 110P will provide power to the connected PD device over the Ethernet cable (see PSE function on Dip Switch configurations). The wire pairs on the cable used for delivering power will depend on the device. The following options are available. RJ-45 PoE Option Alternative A Alternative B Legacy 1 positive 2 positive 3 negative 4 positive negative 5 positive negative 6 negative 7 negative positive 8 negative positive UTP (copper) Power PoE PoE+ IEEE 802.3af (PoE) up to 15.4 Watts for the UTP port. IEEE 802at-2009 (PoE+) Up to 30 Watts on UTP port PoE+ models will also support 802.3af PDs (Type 1) and PoE+ PDs (Type 2) 4
5 Powering Options Jumper Settings Note: The factory settings for Power Sourcing Pinouts will work for most installations as 802.3a and 802at-2009 ( POE/POE+) devices will detect and sync to the correct POE option. However, in the rare case that you need to modify the settings, the procedure is below. In order to select a powering option, the Power Options Jumper settings must be set. Each copper port has a set of Power Option jumpers. To access the Powering Options Jumper settings, unscrew the six side screws on the case and remove the cover plate. Locate the Power Option jumper set and strap the option pins as detailed below. DIP Switches The DIP switches for Bank 1 are accessible through the opening in the side of the enclosure. Bank 1 5
6 Bank 2 To access the DIP switches for Bank 2, unscrew the six side screws on the case and remove the cover plate. Locate the jumper set as detailed below. Bank 2 Note: All switch changes take effect immediately. Switch changes will cycle power to the PD only if the PD Reset switch is set to On or you make changes to the PSE Power switches. 6
7 DIP Switch Settings Bank 1 Auto-negotiation (copper) (Switch 1) Switch Position Copper Port Up (default) Down Auto Off Note: Auto-negotiation should only be turned off, if the copper link partner does not support Auto-negotiation and fixed settings are required by the copper link partner. Auto: When enabled, the media converter will negotiate with its link partner to determine the most optimal parameters for this connection. The S-110P will advertise capabilities of 10 and 100 Mbps, full and half duplex as well as pause to the link partner. If the copper link partner does not support Auto-negotiation, the S-110P will parallel detect to 10 or 100 Mbps and force Half Duplex mode as per IEEE specifications. Off: When the Auto-negotiation switch is set to the OFF position, the media converter will not negotiate the Ethernet parameters with the copper link partner. The parameters used by the media converter will be determined by the Copper Speed (Bank 2 - switch 1) and Duplex Copper (Bank 2 - switch 2) DIP switch settings. Pause receive and send will be disabled. Link Pass-Through Mode (Switch 2) Switch Position Mode Up (default) Down Standard Mode Link Pass-Through Mode 7
8 Standard Mode: In this mode, links on the fiber and copper sides can be brought up and down independently of each other. A loss of link on either the fiber or copper port can occur without affecting the other connection. Link Pass-Through Mode: In this mode, the link state on one connection is directly reflected through the media converter to the other connection. If link is lost on one of the connections, then the other link will be brought down by the media converter. If the installation has a media converter on both ends of the fiber link and both are set-up for Link Pass-Through, then a loss of copper link on the far end device will propagate through both media converters and will result in a loss of link at the near end device. Link Pass-Through Behaviour (A) Remote Media Converter setup for Far End Fault Enabled, Auto-negotiation OFF and Link Mode Standard. (B) Local Media Converter setup for Far End Fault enabled, Link Pass-Through On and Auto-negotiation - OFF (A) Loses fiber connection on its receiver. (A) Sends FEF. (B) Detects FEF signal and shuts down the fiber link. (B) Drops link on copper connection because Link Pass- Through is configured. (A) Link on copper connection is not affected because Link Pass-Through Mode is set to Standard. 8
9 Far End Fault (Switch 3) Switch Position Fiber Port Up (default) Down Enabled Disabled Enabled: If the media converter detects a loss of signal on the fiber receiver, it will immediately disable its fiber transmitter signal on the same port. This, in effect, notifies the fiber link partner that an error condition exists on the fiber connection. If the remote media converter is set up for Far End Fault(FEF) and the local media converter is set up with Link Pass-Through, a loss of fiber link on either the transmit or receive line will be passed through to the local copper connection thus notifying the connected device. If the media converter has been set to Link Pass-Through mode, the effect will be the same as FEF, since the link loss on the fiber receiver will result in bringing down the copper link, which will in turn cause the transmit fiber link to be brought down. Note: This feature only takes affect if Auto-negotiation (Switch 1) has been turned Off. Disabled: The media converter will not monitor for or generate Far End Fault. 9
10 PSE Enable Copper (Switch 4 and 5) Switch Position 4 Switch Position 5 Type Up (default) Up Down Up (default) Down Up PSE enabled normal detection PSE enabled High capacitance detection PSE enabled Legacy device detection Down Down PSE disabled These switches must be set in order to enable the power sourcing function and to indicate the type of device detection required. If the device type is unknown, the default should be used as per IEEE802.3af/at standards. Enabled: When enabled, the media converter will perform Power Sourcing Equipment (PSE) functions as per IEEE802.3af (POE) or 802.3at-2009 (POE+) standards. Disabled: When disabled the media converter will not perform PSE functions. PD Power Reset (Switch 6) Switch Position Mode Up (default) Down Disabled Enabled Disabled: When disabled, the loss of fiber link has no effect on PSE power to the PD device. Enabled: When enabled, if the media converter detects loss of link on the fiber port it will turn off PSE output power to the PD device connected to the copper port. After 2 seconds, the media converter will restore power to the PD and the power will remain on until the fiber link transitions from a link up to link down state. 10
11 Loopback Fiber (Switch 7) Switch Position Mode Up (default) Down Disabled Enabled Disabled: The loopback feature is disabled. This is default position for normal operation. The switch must be set to this position in order for data to pass through the media converter. Enabled: This is a test mode. All data received on the receive (RX) fiber connection is looped back to the transmit (TX) fiber connection. The data link will be disabled; however power to the powered devices will be maintained. This mode will override all other switch settings. Bank 2 Speed Copper (Switch 1) Switch Position Up (default) 100 Down 10 Copper port 100: When Switch 1 is in the Up position, the S-110P will force the speed to 100 Mbps. 10: When Switch 1 is in the Down position the media converter will force the speed to 10 Mbps. Duplex Copper (Switch 2) Switch Position Copper port Up (default) Down Full Duplex Half Duplex 11
12 Full Duplex: In the Up switch position; the media converter will be set to Full Duplex mode. Half Duplex: The media converter will be set to Half Duplex mode. Duplex Fiber (Switch 3) Switch Position Copper port Up (default) Down Full Duplex Half Duplex Note: When Auto-negotiation (SW1) is set to Off, the media converter will use this Duplex setting for the copper port. Full Duplex: In the Up switch position; the media converter will be set to Full Duplex mode. Half Duplex: The media converter will be set to Half Duplex mode. Auto/MDIX (Switch 4) Switch Position Copper port Up (default) Down Auto MDIX Auto: In the Up switch position; the media converter will automatically detect the Ethernet cable s polarity. MDIX: The S-110P will operate as a MDIX device. Installing the SFP Fiber Module 1. SFP models only. 2. Locate the appropriate fiber module and insert the SFP into the opening on the front of the media converter. 12
13 3. Ensure the SFP module is properly seated. The release latch of the SPF fiber transceiver must be in the closed (up) position before insertion. 4. The SFP module may be inserted before or after applying power to the media converter. 5. Proceed with cable connections. Installing the Duplex Fiber Cable 1. Locate a 100Base-X compliant duplex (2 strands) fiber cable with appropriate connectors. 2. Connect the fiber cables from one media converter to the other media converter/switch/fiber device ensuring that the RX and TX are reversed (crossed) at the opposite end. Installing the Simplex Fiber Cable 1. Locate a 100BASE-X compliant simplex (1 strand) fiber cable with appropriate connectors. Ensure that the TX wavelength matches the RX wavelength at the other end and the RX wavelength matches the TX wavelength at the other end. 2. Connect the fiber cable from one media converter to the other media converter/switch/fiber device. Installing the Copper Cable 1. Locate 10/100Base-T compliant copper cables with the appropriate connectors. 2. Connect the RJ-45 cable between the Perle media converter and the device. 13
14 Attaching the Power Cord Strain Relief Clip 1. Remove the screw from the chassis that is closest to the power cord connector. 2. Feed the power cord through the opening in the power cord relief clip. 3. Attach the power cord relief clip to the chassis and secure with the provided screw. 4. Plug the power cord into the AC power connector at the rear of the chassis. 5. Plug the other end of the power cord into an appropriate power outlet. Powering up the Perle Media Converter 1. Connect the Perle supplied power adapter to the media converter. 2. Connect the power adapter to a power source. 3. Check that the PWR LED is lit. 14
15 Extended Temperature models supplied with a PluggableTerminal Block 1. Unplug the terminal block from the Media Converter. 2. Ensure the Power Source is off. 3. Strip both wires 5mm (3/16th inch) 4. Loosen the terminal block screws and connect Positive (+) wire to the left terminal. Connect the Negative (-) wire to the right terminal. Tighten Terminal screws (0.22Nm- 0.25Nm torque). 5. Plug the terminal block into the Media Converter 6. Turn on power source. 7. Check that the PWR LED light is lit. 8. For extra power cable strain relief, attach the strain clip to the case as shown below, and thread the power cable through the clip in either one or two loops. 15
16 Operation Status LED The Perle PoE/PoE+10/100 Rate converting Media converters have status LEDs located on the front panel of the unit. PWR On Power is applied to the unit Blinking (slow) Loopback mode - fiber interface is in loopback mode Blinking (fast) Power On failure. See LED Pattern to determine pattern combination and failure cause LED Pattern LKF LKC 100 PSE Off Off On On SFP incompatible Internal hardware All other LED patterns failure LKF- (Status on Fiber Link) On Fiber link is present Off No fiber link present Blinking (fast) Fiber link up and receiving data 100- (Copper Port) On 100 Mbps (valid link and detected speed is 100 Mbps) Off 10 Mbps (if link is currently established) 16
17 LKC- (Link Status on Copper port) On Copper link is present Off No copper link present Blinking (fast) Copper link up and receiving data PSE Solid Green (Active) The PSE has successfully detected a compliant PD and is applying power over UTP. Solid Orange (Inactive) The PSE is not active. The PSE has been configured to provide power, however a compliant PD not detected - no power applied a PSE has turned off power for Reset function Off (Disabled) The PSE function is disabled in the configuration. Error conditions A blinking red light is an error condition. The led light will cycle with a 3 second stop interval between the error condition code. PSE-LED 1 blink PD Capacitance too high 2 blinks PD Resistance too low or short circuit 3 blinks PD Resistance too high 17
18 Other Features Auto-MDIX Auto-MDIX (automatic medium-dependent interface crossover) detects the signalling on the 10/100BASE-T interface to determine the type of cable connected (straightthrough or crossover) and automatically configures the connection. Pause (IEEE 802.3xy) Integrated Pause signalling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed with data. The Perle media converter can generate and respond to Pause messages. If Auto negotiation is set to On, the media converter will advertise symmetrical and asymmetrical pause. If Auto negotiation is set to Off, the Pause receive and send will be disabled. 18
19 Troubleshooting General 1. Ensure power is supplied to the media converter. Only the Perle provided power supply may be used. 2. Ensure the remote device s fiber connection type is compatible with the media converter. If using a simplex fiber connection, ensure that you have both an Upstream (U) and Downstream (D) media converter. 3. Ensure all cabling is of the correct type and is in good working order. 4. For duplex fiber connections, ensure the RX and TX has been reversed between the two media converters. No connectivity If unable to get full connectivity with all DIP switches in the UP position, this procedure is recommended for troubleshooting. Method 1 1. Set the Link Pass-Through mode to Standard on both media converters. Leave all other switches in the Up position. 2. Connect the copper device to the copper port on the media converter. The LKC LED light indicates good copper connection. If the LKC LED is not lit, then check the copper cable and the attached device. 3. Repeat for the far end media converter. 4. Connect the fiber cable to both media converters. The LKF LED indicates good fiber connection. If no LKF LED then check the fiber cabling. Ensure the transmitter and receiver pairs are crossed. 5. Return units to desired configuration. 19
20 Method 2: The fiber connection can also be verified by configuring the remote media converter for loopback mode. The LKF LEDs on both media converters should be lit. Data should pass through the local converter, over the fiber connection to the remote media converter. At the remote media converter, the data will be looped back and passed through the fiber, back to the local converter and passed to the copper link. No Power to the PD 1. Ensure that the PD is compatible with the S-110P. If the PD is a POE+ device then a POE+ media converter must be used (S-110PP) 2. Ensure that the power supply being used is the one provided with the product 3. If the PD does not support Alternative A (including Legacy PD s), the Power Option Jumpers must be set accordingly. Also ensure the correct pin out for the device. 4. For proper detection of different classes of devices, the dip switches must be set correctly. 20
21 Technical Specifications Power Input Voltage: S-110P models: 46V DC to 57V DC S-110PP models: 52V DC to 57V DC Power consumption : Operating Temperature: (Extended Temp Models): Storage Temperature: (Extended Temp Models): Operating Humidity: Storage Humidity: Operating Altitude: Dimensions: all models : 3.5 watts 0 C to 50 C (32 F to 122 F) -40 C to 75 C (-40 F to 167 F) -25 C to 70 C (-13 F to 158 F) -40 C to 85 C (-40 F to 185 F) 5% to 90% non-condensing 5% to 95% non-condensing Up to 3,048 m (10,000 ft) 120 mm by 80 mm by 26 mm MTBF No Power Adapter PoE (including Power Adapter) PoE+ (including Power Adapter) 1 SFP / 1 copper port 437,237 hours 229,220 hours 81,386 hours 1 SFP / 1 copper port (extended Temp models) 446,216 hours N/A N/A 1 SC/ST / 1 copper port 385,526 hours 214,161 hours 79,404 hours 1 SC/ST / 1 copper port (extended Temp models) 392,490 hours N/A N/A Fiber Cabling Requirements: MM: : 50/125 microns or 62.5/125 microns 9/125 microns Ethernet Copper Cabling Requirements: Category 5 UTP or STP AWG Straight through or Ethernet crossover Note: Please refer the product page on the Perle website for the most up to date models and specifications. 21
22 Fiber Optic Specifications: PoE (P) PoE+ (PP) S-110P-M2xx2 (-XT) S-110PP-M2xx2 (-XT) S-110P-M1SC2U S-110PP-M1SC2U S-110P-M1SC2D S-110PP-M1SC2D S-110P-M1ST2U S-110PP-M1ST2U S-110P-M1ST2D S-110PP-M1ST2D S-110P-S2SC20 (-XT) S-110PP-S2SC20 (-XT) S-110P -S2ST20 (-XT) S-110PP -S2ST20 (-XT) S-110P -S2xx40 S-110PP -S2xx40 S-110P-S2xx80 S-110PP-S2xx80 S-110P-S2xx120 S-110PP-S2xx120 S-110P-S1SC20U (-XT) S-110PP-S1SC20U(-XT) S-110P-S1SC20D (-XT) S-110PP-S1SC20D(-XT) S-110P-S1ST20U S-110PP-S1ST20U S-110P-S1ST20D S-110PP-S1ST20D S-110P -S1SC40U S-110PP -S1SC40U S-110P -S1SC40D S-110PP -S1SC40D S-110P-SFP (XT) S-110PP-SFP (XT) Mode MM MM MM MM MM Wave length (nm) TX: 1310 RX: 1310 TX: 1310 RX: 1550 TX: 1550 RX: 1310 TX: 1310 RX: 1550 TX: 1550 RX: 1310 TX: 1310 RX: 1310 TX: 1310 RX: 1310 TX: 1310 RX :1310 TX: 1550 RX: 1550 TX: 1550 RX: 1550 TX: 1310 RX: 1550 TX: 1550 RX:1310 TX: 1310 RX: 1550 TX: 1550 RX:1310 TX: 1310 RX:1550 TX: 1550 RX:1310 NOTE 1 TX Power (db) Min: -20 Max: -12 Min: -15 Max: 0 Min: -15 Max: -0 Min: -15 Max: -8 Min: -15 Max: -8 Min: -18 Max: -7 Min: -15 Max: -8 Min: -5 Max: 0 Min: -5 Max: 0 Min: 0 Max: 5 Min: -14 Max: -8 Min: -14 Max: -8 Min: -15 Min: -15 Min: -8 Min: -8 RX Power (db) Min: -31 Max: -14 Min: -28 Max: -8 Min: -28 Max: -8 Min: Min: Min: -32 Min: -32 Min: -34 Min: -34 Min: -35 Min: -32 Min: -32 Min: -3 4 Min: -3 4 Min: -33 Min: -33 Budget (db) Note 1: Fiber characteristics will depend on the SFP fiber module selected. 22
23 Warranty / Registration Perle s standard Lifetime Warranty provides customers with return to factory repairs for Perle products that fail under the conditions of the warranty coverage. Details at: Contacting Technical Support Contact information for the Perle Technical Assistance Center (PTAC) can be found at the link below. A Technical Support Query may be made via this web page. Compliance Information FCC This product has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this Guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense. EN 55022, Class A WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. EN 55024, Class A Laser Safety IEC :2007 This product meets Class I Laser safety requirements per IEC :2007 standard and complies with FDA/CDRH 21 CFR and 21CFR WARNING: Visible and invisible laser radiation may be present when cables are not connected. Do not stare into the beam or view the beam directly with optical instruments. Failure to observe this warning could result in an eye injury or blindness. WARNING: Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. Copyright 2015 Perle Systems Limited : All rights reserved. No part of this document may be reproduced or used in any form without written permission of Perle Systems Limited 23
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converters
Perle PoE/PoE+ 10/100/1000 Ethernet Media Converters S-1110P S-1110PP S-1110DP S-1110DPP S-1110P-XT S-1110PP-XT P/N 5500317-13 (Rev C) Overview This document contains instructions necessary for the installation
Perle 10/100 Ethernet Media Converter Module. Installation Guide. P/N (Rev C)
Perle 10/100 Ethernet Media Converter Module Installation Guide C-110-XXXXX CM-110-XXXXX Unmanaged Module Managed Module P/N 5500307-15 (Rev C) Overview This document contains instructions necessary for
Perle Gigabit Media Converters
Perle Gigabit Media Converters Installation Guide S-1000-XXXXXX S-1000-SFP P/N 5500300-19 (Rev A) Overview This document contains instructions necessary for the installation and operation of the Perle
Perle Gigabit Media Converter Module. Installation Guide P/N
Perle Gigabit Media Converter Module Installation Guide Unmanaged Managed C-1000-M2SC05 C-1000-M2LC05 C-1000-S2LC10 C-1000-S2SC10 C-1000-S2LC40 C-1000-S2SC70 C-1000-S2LC70 C-1000-S1SC10U C-1000-S1SC10D
Perle S-10GRT-SFP Media Converter Installation Guide
Perle S-10GRT-SFP Media Converter Installation Guide P/N 5500432-10 (Rev-E) Overview This document contains instructions necessary for the installation and operation of the Perle S-10GRT-SFP Standalone
Perle 10GT Media Converters
Perle 10GT Media Converters Installation Guide S-10GT-SFP S-10GT-XFPH Part#5500336-10(Rev B) OverView This document contains instructions necessary for the installation and operation of the Perle S-10GT
Perle Advanced Powered Ethernet Extenders Installation Guide
Perle Advanced Powered Ethernet Extenders Installation Guide 10/100 10/100/1000(Gigabit) exp-xs110l exp-xs110e exp-xs1110l exp-xs1110pe exp-xs1110e Part# 5500332-11 (Rev A) Overview This document contains
Perle SMI Media Converter Installation Guide
Perle SMI Media Converter Installation Guide P/N 5500316-10 Introduction Perle SMI Media Converters provide seamless high-speed managed integration of Ethernet to Fiber networks. Overview This guide contains
Perle SMI Media Converter Installation Guide
Perle SMI Media Converter Installation Guide P/N 5500316-14 Overview This guide contains instructions necessary for the installation and operation of the Perle SMI Media Converter. This media converter
Perle SMI Media Converter Installation Guide
Perle SMI Media Converter Installation Guide Part# 5500316-16 Introduction Perle SMI Media Converters come in two different models. The 100/110 and the 1000/1110 Media Converters provide high-speed managed
Perle 10GT Media Converter Modules
Perle 10GT Media Converter Modules Installation Guide C-10GT-SFP CM-10GT-SFP C-10GT-XFPH CM-10GT-XFPH P/N 5500337-10 (Rev B) Overview This document contains instructions necessary for the installation
Perle 10G Media Converter Modules
Perle 10G Media Converter Modules Installation Guide CM-10G-STS C-10G-STS CM-10G-XTS C-10G-XTS CM-10G-XTX C-10G-XTX CM-10G-XTSH C-10G-XTSH CM-10G-XTXH C-10G-XTXH P/N 5500326-10 (Rev C) Overview This document
Perle Protocol Transparent Media Converter Modules
Perle Protocol Transparent Media Converter Modules Installation Guide C-4GPT-DSFP CM-4GPT-DSFP Part#5500335-10 (Rev A) Overview This document contains instructions necessary for the installation and operation
Perle 10G Media Converter Modules
Perle 10G Media Converter Modules Installation Guide CM-10G-STS C-10G-STS CM-10G-XTS C-10G-XTS CM-10G-XTX C-10G-XTX CM-10G-XTSH C-10G-XTSH CM-10G-XTXH C-10G-XTXH P/N 5500326-10 Overview This document contains
Perle Cx-10GR-STS Media Converter Modules
Perle Cx-10GR-STS Media Converter Modules Installation Guide C-10GR-STS CM-10GR-STS P/N 5500435-10 (Rev G) Overview This document contains instructions necessary for the installation and operation of the
Perle MCR200 Installation Guide
Perle MCR200 Installation Guide P/N 5500322-10 Introduction The Perle MCR200 Chassis is a 2 slot chassis able to accommodate up to 2 Perle Media Converter modules or 1 Media Converter Module and an MCR-MGT
Perle 10/100/1000 Ethernet Extender Modules. 10/100 10/100/1000 (Gigabit)
Perle 10/100/1000 Ethernet Extender Modules 10/100 10/100/1000 (Gigabit) ex-1c/cm110-rj ex-1c/cm110-bnc ex-1c/cm110-tb ex-1c/cm1110-rj ex-1c/cm1110-bnc ex-1c/cm1110 -TB Part# 5500331-11(Rev A) Version:
LNP-0602 series. 6-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 2*100Fx. User Manual
LNP-0602 series 6-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 2*100Fx User Manual FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A
10/100TX to 100FX w/ 1 PoE Injector Industrial Media Converter User Manual
10/100TX to 100FX w/ 1 PoE Injector Industrial Media Converter User Manual v1.02 FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to
Perle IDS-108F(XT) Unmanaged 10/100 Ethernet Switches. Installation Guide. P/N (Rev G)
Perle IDS-108F(XT) Unmanaged 10/100 Ethernet Switches Installation Guide P/N 5500339-10 (Rev G) Overview This document contains instructions necessary for the installation and operation of the Perle IDS-108F
exp-s1110pe PoE+ Gigabit Ethernet Extenders
perle.com https://www.perle.com/products/10-100-1000-poe+-ethernet-extender.shtml exp-s1110pe PoE+ Gigabit Ethernet Extenders 10/100/1000 PoE+ Ethernet Copper Extenders Extends 10/100/1000Base-T up to
4-port 10/100TX + 1 or 2-port 100FX Industrial Switch. User Manual
4-port 10/100TX + 1 or 2-port 100FX Industrial Switch User Manual Rev.1.03 Sep-2010 FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541 PoE Model: KSD-541-P. Installation Guide
Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports Basic Model: KSD-541 PoE Model: KSD-541-P Installation Guide DOC.080104-1- (C) 2008 KTI Networks Inc. All rights reserved.
1 10/100TX FX w/ 1 PoE Injector Industrial Switch. User Manual
1 10/100TX + 1 100FX w/ 1 PoE Injector Industrial Switch User Manual CE Mark Warning This is a Class-A product. In a domestic environment this product may cause radio interference in which case the user
IEC-0101FT Industrial 10/100TX to 100M-FX Slim Type Converter User Manual
Lantech IEC-0101FT Industrial 10/100TX to 100M-FX Slim Type Converter User Manual FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
4 10/100/1000T Mini-GBIC with 4 IEEE 802.3at High Power PoE Industrial Wide Temperature Switch. User Manual SISTP LRT
4 10/100/1000T + 2 1000 Mini-GBIC with 4 IEEE 802.3at High Power PoE Industrial Wide Temperature Switch User Manual V1.0 September-2013 FCC Warning This Equipment has been tested and found to comply with
KSD-800 Series. Installation Guide. Industrial 8-Port Fast Ethernet Switches with Fiber Connectivity DOC A -1-
KSD-800 Series Industrial 8-Port Fast Ethernet Switches with Fiber Connectivity Installation Guide DOC.110516A -1- (C) 2005 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced
8-port 10/100TX + 2-Port 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Ethernet Switch User Manual
8-port 10/100TX + 2-Port 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Ethernet Switch User Manual FCC Warning This Equipment has been tested and found to comply with the limits for a
LNP series. 5-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 1*10/100Tx, 12~36VDC Input.
LNP-0500-24 series 5-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 1*10/100Tx, 12~36VDC Input User Manual FCC Warning This Equipment has been tested and found to comply with
IMC-21A Quick Installation Guide
IMC-21A Quick Installation Guide Moxa Industrial Media Converter Edition 5.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777
General and Copyright Notice Warranty OmniConverter Limitation of Warranty Environmental Notices User Manual
OmniConverter GPoE+/Sx Unmanaged 8-Port PoE/PoE+ Switch User Manual General and Copyright Notice This publication is protected by U.S. and international copyright laws. All rights reserved. The whole or
10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter. AMG9011G-H (-40 to 75C) User Manual
10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter AMG9011G-H (-40 to 75C) User Manual www.amgsystems.com Content Overview...1 Introduction... 1
100Base-FX to 10/100Base-TX. PoE. Media Converter. FCU-1802Px. User s Manual
100Base-FX to 10/100Base-TX PoE Media Converter FCU-1802Px User s Manual Trademarks Copyright Antaira Technologies 2013. Contents subject to revision without prior notice. Antaira is a registered trademark
Lantech. IPES /100TX with 4 PoE Injectors 24~48VDC Industrial Switch. User Manual
Lantech IPES-0008-4 8 10/100TX with 4 PoE Injectors 24~48VDC Industrial Switch User Manual V1.00 Jun 2010 FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital
OmniConverter GPoE+/M Managed 4 and 8-Port PoE/PoE+ Switch. Quick Start Guide
OmniConverter GPoE+/M Managed 4 and 8-Port PoE/PoE+ Switch Quick Start Guide General and Copyright Notice This publication is protected by U.S. and international copyright laws. All rights reserved. The
Industrial 5-Port Fast Ethernet Switches. with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541. PoE Model: KSD-541-HP. Installation Guide
Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports Basic Model: KSD-541 PoE Model: KSD-541-HP Installation Guide DOC.141201-1- (C) 2014 KTI Networks Inc. All rights reserved.
IMC-21GA Quick Installation Guide
IMC-21GA Quick Installation Guide Moxa Industrial Media Converter Edition 4.0, June 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777
5 10/100TX w/ 4 PoE Injector Industrial Switch. User Manual
5 10/100TX w/ 4 PoE Injector Industrial Switch User Manual V1.01 Nov-2010 CE Mark Warning This is a Class-A product. In a domestic environment this product may cause radio interference in which case the
Hypercable injecteur HPOE - Industrial IEEE 802.3at Gigabit PoE Injector. User Manual. v.1.0 Jun Mail :
Industrial IEEE 802.3at Gigabit PoE Injector User Manual v.1.0 Jun-2011 FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
IMC-21 Quick Installation Guide
IMC-21 Quick Installation Guide Moxa Industrial Media Converter Edition 5.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777
Lantech. IPGS-0204DSFP 4 10/100/1000T PoE at/af + 2 Dual Speed SFP Industrial Unmanaged Switch
Lantech IPGS-0204DSFP 4 10/100/1000T PoE at/af + 2 Dual Speed SFP Industrial Unmanaged Switch IGS-0204DSFP 4 10/100/1000T + 2 Dual Speed SFP Industrial Unmanaged Switch User Manual V1.00 Jul-2016 Content
BLACKBOX NETWORK SERVICES. one source for worldwide infrastructure services
BLACKBOX NETWORK SERVICES one source for worldwide infrastructure services 24 Port 10/100Mbps plus 2 Gigabit TX/FX Auto-MDIX Modular Gigabit Ethernet Switch User s Manual FCC Warning This device has been
ex-s1110-xt Gigabit Ethernet Extenders
ex-s1110- Gigabit Ethernet Extenders perle.com/products/10-100-1000-industrial-ethernet-extender.shtml 10/100/1000 Industrial Temperature Copper Extender Extends 10/100/1000Base-T Ethernet up to 10,000
IFS MC201-1P/1FS User Manual
IFS MC201-1P/1FS User Manual P/N 1076525 REV A ISS 07FEB12 Copyright Trademarks and patents Manufacturer Version Certification FCC compliance ACMA compliance European Union directives 2012 UTC Fire & Security
PoE Powered Gigabit Ethernet Media Converters 1000BASE-T TO 1000BASE-SX/LX. KGC-352 Series. Installation Guide
PoE Powered Gigabit Ethernet Media Converters 1000BASE-T TO 1000BASE-SX/LX KGC-352 Series Installation Guide DOC.070820-KGC-352-1- (C) 2007 KTI Networks Inc. All rights reserved. No part of this documentation
PoE Powered 10/100BASE-TX to 100BASE-FX Media Converters. KC-351 Series. Installation Guide
PoE Powered 10/100BASE-TX to 100BASE-FX Media Converters KC-351 Series Installation Guide -1- DOC.070820-KC-351 (C) 2007 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced
Entry Line Industrial Gigabit Ethernet Bridging Converter, PoE+ optional 1x 10/100/1000Base-T, 1x 100/1000 SFP
Entry Line Industrial Gigabit Ethernet Bridging Converter, PoE+ optional 1x 10/100/1000Base-T, 1x 100/1000 SFP General The IP protocol has already left the in-house environment and is going to take all
General. 5 and 8 port Fast Ethernet switches. 6 and 8 Port Gigabit Ethernet switches. Switches with fiber uplink
Entry Line Industrial Gigabit Ethernet Switch 4x 10/100/1000Base-T with PoE+, 1x 10/100/1000Base-T or 100/1000Base-X Combo Port, 1x 100/1000Base X SFP Slot General The IP protocol has already left the
USER S MANUAL. 10/100/1000Base-T 1000Base-SX/LX Gigabit Ethernet Converter GEP-5300TF-C GEP-5400TF-C
For full coverage of your warranty, be sure to register your product using the enclosed registration card. 10/100/1000Base-T 1000Base-SX/LX Gigabit Ethernet Converter GEP-5300TF-C GEP-5400TF-C 1000Base-T/SX
MF727xS INDUSTRIAL 10/100BASE-TX TO 100BASE-FX MEDIA CONVERTER. Installation Guide
1 INDUSTRIAL 10/100BASE-TX TO 100BASE-FX MEDIA CONVERTER Installation Guide October 2008 VERSITRON, Inc. 83C Albe Drive Newark, DE 19702 800-537-2296 2 PROPRIETARY DATA All data in this manual is proprietary
LevelOne FSW PoE Fast Ethernet Switch User Manual
LevelOne FSW-0809 4+4 PoE Fast Ethernet Switch User Manual v1.0-0706 Safety FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to
16/24 Port 10/100 Auto-Sensing Dual Speed Ethernet Switch
12 Omnitron Systems Technology, Inc. Omnitron Systems Technology, Inc. 1 FlexSwitch TM 600X 16/24 Port /0 -Sensing Dual Speed Ethernet Switch User s ual 27 Mauchly #201, Irvine, CA 92618 (949) 250-65 Fax:
10/100BASE-TX TO 100BASE-FX MEDIA CONVERTERS EM4000 EM4001. Installation Guide
10/100BASE-TX TO 100BASE-FX MEDIA CONVERTERS EM4000 EM4001 Installation Guide DOC.050523-EM400X -1- The information contained in this document is subject to change without prior notice. Copyright (C) All
Gigabit Ethernet Copper-to-Fiber Media Converter - SM LC - 10 km
Gigabit Ethernet Copper-to-Fiber Media Converter - SM LC - 10 km Product ID: ET91000SM10 This Gigabit Ethernet to fiber media converter is a cost-effective way to extend your network, or extend the distance
MF BASE-T to 1000BASE-X INDUSTRIAL MEDIA CONVERTER WITH SFP SUPPORT INSTALLATION GUIDE
1000BASE-T to 1000BASE-X INDUSTRIAL MEDIA CONVERTER WITH SFP SUPPORT INSTALLATION GUIDE September 2006 VERSITRON, Inc. 83 Albe Drive - Suite C Newark, DE 19702 2 PROPRIETARY DATA All data in this manual
ST-POEAF-S16-RM. 16 port PoE switch. User Guide
ST-POEAF-S16-RM 16 port PoE switch User Guide IMPORTANT This user s guide contains information on the limitations regarding product use and function and information on the limitations as to liability of
Lantech. IPGS-0005T /100/1000T PoE at T Industrial Unmanaged Switch. User Manual
Lantech IPGS-0005T-4 4 10/100/1000T PoE at + 1 1000T Industrial Unmanaged Switch User Manual V1.00 Jan-2018 Content Overview... 1 Introduction... 1 Features / Model List... 2 Packing List... 3 Safety Precaution...
INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS. KCD-400 Series. Installation Guide
INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS KCD-400 Series Installation Guide DOC.060227-KCD-400-1- (C) 2005 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced
10/100Base-TX to 100Base-TX Mini Converter. Operation Manual
10/100Base-TX to 100Base-TX Mini Converter Operation Manual COPYRIGHT All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by
Industrial 3-Port Fast Ethernet Media Converter Switches
Industrial 3-Port Fast Ethernet Media Converter Switches KSD-103-A series KSD-103-B series Installation Guide DOC.081111 1/20 (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation
5-Port 10/100Mbps with 4-Port PoE. Industrial Fast Ethernet Switch ISW-504PT / ISW-514PT / ISW-514PT15 / ISW-514PTF. User's Manual
5-Port 10/100Mbps with 4-Port PoE Industrial Fast Ethernet Switch ISW-504PT / ISW-514PT / ISW-514PT15 / ISW-514PTF User's Manual Trademarks Copyright PLANET Technology Corp. 2010 Contents subject revision
LNP-0501 Series. User Manual. 5-Port Industrial PoE+ Unmanaged Ethernet Switches with 4*10/100Tx (30W/Port) + 1*10/100Tx
LNP-0501 Series 5-Port Industrial PoE+ Unmanaged Ethernet Switches with 4*10/100Tx (30W/Port) + 1*10/100Tx User Manual Version 2.2 i Copyright 2018 Antaira Technologies, LLC All Rights Reserved This document
Copyright PLANET Technology Corp Contents subject to revision without prior notice.
Copyright Copyright PLANET Technology Corp. 2004. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject
6 10/100/1000TX + 2G Fiber Industrial Ethernet Switch User Manual
6 10/100/1000TX + 2G Fiber Industrial Ethernet Switch User Manual FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the
Hardened Ethernet to VDSL2 Extender. User Guide. Revision History. Industrial Ethernet to VDSL2 Extender with Wide Operating Temp. Rev.1.
Hardened Ethernet to VDSL2 Extender User Guide Revision History Rev.1.03 Dec 2009 Industrial Ethernet to VDSL2 Extender with Wide Operating Temp. Document Release Date Revision Initials 1.00 Jun 04, 2009
Industrial 8-Port 10/100TX 802.3at PoE+ + 2-Port Gigabit TP/SFP Combo Ethernet Switch IFGS-1022HPT. User s Manual
Industrial 8-Port 10/100TX 802.3at PoE+ + 2-Port Gigabit TP/SFP Combo Ethernet Switch IFGS-1022HPT User s Manual Table of Contents 1. Package Contents... 3 2. Hardware Introduction... 4 2.1 Physical Dimensions...
Installation Guide. 100BASE-TX/100BASE-FX Fast Ethernet Media Converter NC-200FT/FC. -1-iIiNC-200FT/FC P/N:
Installation Guide 100BASE-TX/100BASE-FX Fast Ethernet Media Converter NC-200FT/FC -1-iIiNC-200FT/FC P/N:750-0166-001 Table le of Contents General Description...3 Specifications...4 Connectors & Cables...5
PTC-101-M12 Hardware Installation Guide
PTC-101-M12 Hardware Installation Guide Moxa Industrial Media Converter Third Edition, May 2014 2014 Moxa Inc. All rights reserved. P/N: 1802001016021 Overview The PTC-101-M12 industrial media converter
Multi-Power Miniature Media Converter 10/100/1000 JUNE 2007 LGC322A-NPS LGC320A-NPS, LGC321A-NPS,
Copyright 2006. Black Box Corporation. All rights reserved 1000 Park Drive * Lawrence, PA. 35055-1018 * 724-746-5500 * Fax 724-746-0746 56-80830BB-00 Rev A1 June 2007 JUNE 2007 LGC320A, LGC321A, LGC322A,
M727xS 10/100BaseTX-FX Selectable Media Converter Installation Guide
M727xS 10/100BaseTX-FX Selectable Media Converter Installation Guide Copyright January 2004 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 A010430357 The information contained in this document
Industrial Ultra Power over Ethernet Splitter IPOE-171S
Industrial Ultra Power over Ethernet Splitter IPOE-171S User s Manual Table of Contents 1. Package Contents... 3 2. Product Features... 4 3. Product Specifications... 5 4. Hardware Introduction... 8 4.1
MDI/MDIX) FEP-32005T-2
TM Mico-Switch/5 5 Port 10/100Base-TX Switch (Auto MDI/MDIX) FEP-32005T-2 U SER S M ANUAL (Auto MDI/MDIX) FEP-32005T-2 TM TM Package Contents Package contents include the following: Micro-Switch/5; 5 Port
MC100FX-TX-PoE Media Converter User Manual
GE Security MC100FX-TX-PoE Media Converter User Manual P/N 1069178 REV 1.0 ISS 22FEB10 Copyright Disclaimer Trademarks and patents Intended use FCC compliance 2010 GE Security, Inc. This document may not
Features and Benefits. Certifications
EDS-P206A Series 6-port unmanaged Ethernet switches with 4 IEEE 802.3af/at PoE+ ports Features and Benefits IEEE 802.3af/at compliant PoE and Ethernet combo ports Up to 30 W output per PoE port 12/24/48
Lantech IPGC-0101DSFP. User Manual. 10/100/1000T (PoE at) to 100/1000M SFP Industrial Switch Converter
Lantech IGC-0101DSFP IPGC-0101DSFP 10/100/1000T (PoE at) to 100/1000M SFP Industrial Switch Converter User Manual Dec 2016 Recommendation for Shielded network cables STP cables have additional shielding
Fast Ethernet Converter. User Guide MICROSENS
Fast Ethernet Converter User Guide MICROSENS Rev.1.25 Jan-2010 Content Introduce... 1 Features... 2 Package Contents... 3 Hardware Description... 4 Front Panel... 4 Ports... 5 LED Indicators... 5 DIP-switch...
M727xSP. PoE Powered. Ethernet Media Converter 10/100BASE-TX TO 100BASE-SX/LX. Installation Guide
M727xSP PoE Powered Ethernet Media Converter 10/100BASE-TX TO 100BASE-SX/LX Installation Guide September 2009 VERSITRON, Inc. 83 Albe Drive - Suite C Newark, DE 19702 www.versitron.com www.versitron.com
Preface. Manual Revisions. Trademarks
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions
KFC-200. Installation Guide
KFC-200 10/100BASE-TX to 100BASE-FX Media Converters Installation Guide DOC.121221-1- (C) 2011-2012 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or
Korenix JetNet 3000 Series Industrial Entry-Level Ethernet Rail Switch User s Manual
Korenix JetNet 3000 Series Industrial Entry-Level Ethernet Rail Switch User s Manual Fourth Edition, DEC, 2007 www.korenix.com Korenix JetNet 3000 Series Industrial Entry-Level Ethernet Rail Switch User
Features and Benefits. Certifications
EDS-P308 Series 8-port unmanaged Ethernet switches with 4 IEEE 802.3af PoE ports Features and Benefits 4 IEEE 802.3af-compliant PoE and Ethernet combo ports Up to 15.4 W output at 48 VDC per PoE port Intelligent
Product names mentioned in this manual may be trademarks or registered trademarks of those products and are hereby acknowledged.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
OmniConverterTM. OmniConverter FPoE/SL, FPoE/S and FPoE+/S 10/100 Media Converter with Power over Ethernet (PoE or PoE+) KEY FEATURES
OmniConverterTM 10/100 Media Converter with over Ethernet (PoE or PoE+) The are multiport media converters that convert 10/100BASE-T copper to 100BASE-X fiber and support -over-ethernet (PoE and PoE+).
ROCKETLINX ES7110 ES7110/ES7110-VB
ROCKETLINX ES7110 ES7110/ES7110-VB QUICK INSTALLATION GUIDE 2000550 Rev E Release Date - August 2015 INTRODUCTION The RocketLinx ES7110 series is an industrial Power over Ethernet (PoE) switch with eight
8-Port IP40 IEEE802.3af PoE Unmanaged Industrial Switch User s Manual
8-Port IP40 IEEE802.3af PoE Unmanaged Industrial Switch User s Manual Version 1.1 Content Overview... 1 Introduction... 1 Features... 2 Technical Specifications... 3 Packing List... 5 Safety Precaution...
ICPDAS FSM-510G Series Ethernet Management Switch Quick Start
ICPDAS FSM-510G Series Ethernet Management Switch Quick Start Version 1.0, Dec 2014 Overview The Management Ethernet Switch solutions are designed for supporting standard industrial applications. Managed
User Manual Entry Line Industrial Gigabit Ethernet High Power 60/95 W PoE Injector
User Manual Entry Line Industrial Gigabit Ethernet High Power 60/95 W PoE Injector Gigabit Ethernet Switch with PoE+ for Industrial Use Page 2/11 Table of Contents General... 3 Benefits... 3 Front View...
Signamax Connectivity Systems Gigabit Ethernet SFP Media Converter
Signamax Connectivity Systems Model - 065-1195SFP 065-1195SFPI User s Guide 1 Quick Start Guide This quick start guide describes how to install and use the Gigabit Ethernet SFP media converter. The converter
Moxa Industrial Media Converter PTC-101-M12 Hardware Installation Guide
Moxa Industrial Media Converter PTC-101-M12 Hardware Installation Guide First Edition, February 2012 2012 Moxa Inc. All rights reserved. P/N: 1802001016020 Overview Moxa Industrial Media Converter, which
Gigabit Ethernet Media Converter
Quick Start Guide This quick start guide describes how to install and use the Gigabit Ethernet media converter. The converter introduced here provides one channel media conversion solution. Physical Description
Flexible integration into mixed network environments. Gigabit Ethernet Copper-to-Fiber Media Converter - SM LC - 20 km. StarTech ID: ET91000SM20
Gigabit Ethernet Copper-to-Fiber Media Converter - SM LC - 20 km StarTech ID: ET91000SM20 This Gigabit Ethernet to fiber media converter is a cost-effective way to extend your network, or extend the distance
10/100BASE-TX TO 100BASE-FX MEDIA CONVERTERS. KC-300DM Series. Installation Guide
10/100BASE-TX TO 100BASE-FX MEDIA CONVERTERS KC-300DM Series Installation Guide -1- DOC.060215-KC-300D (C) 2003 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in
Ethernet 10Base-T Hub EH-500 EH-800A EH Rev. 3.0
Ethernet 10Base-T Hub EH-500 EH-800A EH-1600 Rev. 3.0 Trademarks Copyright PLANET Technology Corp. 1998. PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject
Industrial 1-Port Coax/UTP Long Reach PoE+ 4-Port. 10/100TX PoE Extender LRP-104CET. User s Manual
Industrial -Port Coax/UTP Long Reach + -Port 0/00TX Extender User s Manual Table of Contents. Package Contents.... Application Diagram.... Point to Multi-point..... LRP-0CH to..... LRP-0UH to... 5. Multi-Point
Alternative B Type Mid-Span Power Sourcing Equipment. User s Guide
Alternative B Type Mid-Span Power Sourcing Equipment User s Guide REGULATORY STATEMENTS FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device,
Quick Start Guide. Installation. User s Manual 1
Quick Start Guide This quick start guide describes how to install and use the Hardened Ethernet Extender. This is the Hardened Ethernet Extender of choice for harsh environments constrained by space. Installation
Owner s Manual. Media Converters Models: N SC & N ST
200605219 93-2565 N784 SMC OM.qxd 6/7/2006 3:54 PM Page 1 Warranty Registration Register online today for a chance to win a FREE Tripp Lite product! www.tripplite.com/warranty Owner s Manual Media Converters
OPERATOR MANUAL. OSD2053P SERIES MICRO 10/100Base-T to 100Base-X MEDIA CONVERTER. WITH PoE SOURCE
OPERATOR MANUAL OSD2053P SERIES MICRO 10/100Base-T to 100Base-X MEDIA CONVERTER WITH PoE SOURCE INDEX 1 1 TECHNICAL SUMMARY... 4 1.1 BRIEF DESCRIPTION... 4 1.1.1 OVERVIEW... 4 1.1.2 APPLICATIONS... 4
Gigabit Ethernet Fiber Media Converter - Compact - 850nm MM LC - 550m
Gigabit Ethernet Fiber Media Converter - Compact - 850nm MM LC - 550m Product ID: MCM1110MMLC This fiber media converter offers an easy, cost-effective way to extend your network over Gigabit fiber. It
LNX-0702G-SFP Series
LNX-0702G-SFP Series 7-Port Industrial Gigabit Unmanaged Ethernet Switches 5*10/100/1000Tx + 2*100/1000 SFP Slots User Manual Version 1.0 i Copyright 2014 Antaira Technologies, LLC All Rights Reserved